AMERICOM. Digital Telephone System. System User s Guide

Transcription

1 AMERICOM Digita Teephone System System User s Guide

2 This user guide is appicabe for the foowing system and teephone modes: System Modes: DO408 Rev. A and ater DO8 16 Rev. C and ater D1632 Rev. Aand ater Teephone Modes: 701os-xx 7016S-XX 7 102X-Xx 711os-xx 7110x-xx 7116S-XX 7116X-Xx

3 TABLE OF CONTENTS Using This Guide... 1 Rnowing Your Teephone....2 Using Your Speakerphone....6 WhattbeLightsMean... WhattheRingsMean.... Using Your Teephone....9 Answering Cas....9 MakingCas Hoding Cas Transferring Cas Making Conference Cas Messaging Programming Your Teephone Autodia Programming Station Speed Dia Programming Response Message Programming Automatic Redia Programming Assist Button Programming U sing Misceaneous Features AccountCodeEntry Automatic Set Reocation Background Music Ca Forwarding Ca Override Features CaWaiting... 7 Departmenta Station Operation Dispay Contrast Adjustment Do Not Disturb MuteButton... 9 Paging Persona Ringing Tones Privacy PuseKone Switching Voice Announce Bocking I/

4 Tabe of Contents (continued) Gossary Index Figures 1.16-Line LCD Speakerphone , , o-line Monitor Teephone...,...., Tabes 1. Quick Reference Guide Dispay Summary iv

5 Using This Guide To hep you use your teephone to its fuest capacity, we have written a cear, comprehensive user guide. This guide is divided into eight sections, each of which is marked with a tab for easy access. These sections te you how to: Answer cas, Makecas, Hod cas, * Transfer outside cas, * Make conference cas, Leave messages, Program your teephone, and Perform misceaneous functions. For your convenience, a quick reference guide, a gossary and an aphabetica index are incuded in the back of this user guide. If you have an LCD speakerphone (Figure ), Tabe 3 gives you a summary of what you wi see in the dispay and when you wi see it.

6 Knowing Your Teephone The foowing features on your teephone are expained in terms of what they aow you to do. The teephones in Figures 1 and 2 are the same except for the additiona programmabe buttons and the dispay shown in Figure 1. Hod Button - Paces a ine on hod - Storespauses in number sequences whie programming - Used for programming and accessing second eve autodias Voume Contro - Reguates the voume of the speaker and the handset. Intercom Button (ITCM) - Seects an intercom ine - Initiates many of the features of the teephone Ringer Voume Contro (LO, HI, OFF) - Lets you vary ringer voume from ow to high to off TAP Button (must be preprogrammed for either function) - Recas dia tone, or - Activates host system features Transfer/Conference Button (TRANSKONF) - Transfers cas - sets up conference cas Mute Button - Keeps tire person on the ine from hearing your conversation - Adjusts the contrast of the dispay from ight to dark Speaker Button (SPKR) - Turns your speaker on or off - Disconnects a ca when your handset is on-hook - Ends or cances programming Message Waiting Light - Tes you that there is a message for you Continued on next page

7 Knowing Your Teephone (continued) Programmabe Buttons - Aow you to program your teephone for automatic diaing functions - Aow you to program your teephone for Direct Station Seection (DSS) - Show which ines are either in use or on hod (red ight) - Show which ines are in use by you (green ight) Dua-Line Aphanumeric Dispay - Dispays time, day and date - Keeps you apprised of the status of your teephone - Provides programming prompts Headset Jack (used ony with a 16-ine speakerphone) - Aows you to use your teephone privatey and handsfree - Heps improve operation of high-ca-voume businesses 3

8 -.-r -.,--.,.I.,.,,, (I. _.-_, _.^ Handset \i fz Ringer Voume I Dua Lamps (red and green) F Programmabe Buttons (Lines or DSS/BLF) fiansfer/ Conference Button Mute * Button L- / I I \ Message Waiting Voume Light Button Contro Button Figure Button LCD Speakerphone Programmabe Buttons t Programmabe Buttons (Lines or DSSIBLF) J -Auto Redia Button (Defaut) -Voice Announce Bock Button (Defaut) - Do Not Disturb Button (Defaut)

9 Keypad Buttons-, 1 Dua Lamps (Red and Green) f Programmabe Buttons (Lines or DSS/BLF) Transfer/Conference J I Message Waiting 7 HodJ Voume -Intercom Light Button Contro Button I I I / Figure 2. o-button Monitor Teephone

10 Using Your Speakerphone A speakerphone gives you the freedom to use your teephone without ifting the handset. After initia contact is made, you can carry on a teephone conversation and sti be free to do other things. Whenever the instructions Lift the handseto tak appear in this guide, they may be ignored if you have a speakerphone. During the course of a conversation you can aways switch from the speakerphone to the handset for privacy. To do this, just ift the handset and tak. To return to speakerphone use, press the SPKR button and hang up the handset. To manuay pace a ca using your speakerphone: I 1. Press the ine button or the 0 ITCM button. 2. Dia the number. 3. When party answers, tak. To autodia using your speakerphone, just press the programmed button and tak when your party answers. I To answer a ca with your speakerphone: 1. Press the ine button with fashing red ight. 2. When party answers, tak. To end a ca with your speakerphone, just press 0 SPKR.

11 What the -Lights Mean. The ights on your teephone et you know the status of ines, features and the intercom. Next to a DSS/BLF button: Steady red = station is in use. Fashing red = station is receiving a ca. Fast fashing red = station-to-station messaging has been set. Next to a ine button: Steady green = this is your ine, either on-hook or off-hook, when the ine is active. Fashing green = your ine is on hod. Faster fashing green = your ine has been recaed from hod. Steady red = another station is using this ine. Fashing red = a ca is coming in on this ine. Faster fashing red = the ca has been paced on hod by another station. Next to a feature button: Steady red = the feature is on. Light off = the feature is off. Next to an intercom button: Steady red with a quick fash = you are using your intercom. Fast fashing red = auto-redia is in use. Fast.fashing red with repeated off periods = night mode is on. Steady fashing red = anlcd message is set on your teephone. What the Rings Mean Two short rings = intercom ca. Singe onger ring = outside ca. One short tone burst = voice announce. Three short tone bursts = ring back from a hed ca, caback from a queued ca. You can vary the ringing tone of your teephone, choosing from one of four different rings. This way, you can identify your ring even though you may not be cose to your teephone. Additionay, so you won t be disturbed when you re busy on a ca and another ca rings at your station, the ring voume is subdued automaticay. 7

12 Using Your Teephone Outside Cas Answering Cas To answer, Press button of ringing ine (fashing red ight). a Lift handset to tak. NOTE: Pressing a button is not necessary if Your ringing ine is your prime ine, or Your teephone has ringing ine preference. Intercom Cas To answer a voice ca, Speak toward the teephone. e Lift handset if privacy is desired. NOTE: Voice cas can be bocked. See the discussion tited Voice Announce Bocking for detais. To answer a tone ca, * Lift handseto tak. Ca Pickup To answer a ca that is ringing within your group, Lift handset. 0 Press ITCM. Continued on next page

13 Ca Pickup (continued) You can answer a ca that is ringing at any teephone if you know the extension of the ringing teephone, Lift handset. Press 0 TCM, o Dia Dia extension number of ringing teephone. Night Transfer After the attendant sets up the night transfer feature, an outside ca can be answered from any station within the system. Press TCM when you hear ringing. Dia Answer ca. Secure Off-Hook Voice Announce Your teephone can be set up for Secure Off-Hook Voice Announce (SOHVA). This feature aows an intercom caer to break into your outside ca with an announcementhrough your handset receiver. A Secure Off-Hook Voice Announce consists of both severa short tone bursts and an announcement in the handset receiver. The distant party cannot hear the announcement. To respond O Verbay: Press and hod MUTE button down and repy by speaking into handset. Distant party cannot hear response. * Non-verbay: If the announcing station has an LCD speakerphone, pressing a preprogrammed message response button causes a message to appear in their dispay and disconnects the announcing station. Continued on next page... 10

14 If your station is set up for station monitoring, when a BLF ight fashes (indicating station ringing), you can pick up the ca by pressing the DSS button. However, after you answer the ca and either put it on HOLD or begin to transfer it, the DSS ight wi go out. Press if you have to retrieve the ca. 11

15

16 Making Cas Outside Cas To dia outside cas manuay, Press button to seect ine. Listen for dia tone. Dia number. When party answers, 0 Lift handset to tak. NOTE: Seecting a ine is not necessary if a prime ine has been assigned to your teephone. For automatic diaing, just press the programmed button and ift handseto tak. If your system has ine groups, 0 * Press rtch4. * Dia ine group access code 9 = ine group 1.m 81= ine group 2 82 = ine group 3 83 = ine group 4 0 Listen for dia tone. Dia number. If a the ines in the group are busy, you can pace your station in a queue to await an ide ine. 0 Press rtcm. * Dia the ine group access code (9,81,82,83). Hear busy tone. Continued on next page. 13

17 Outside Cas (continued) Dia and hang up. When ine group is free, your teephone wi sound severa short tone bursts.. Lift handset, hear dia tone, and pace ca. To cance queuing, Press Q rtcm. Dia a (@ and hang up, When you share a ine with another station and the ine is busy, you can pace your station in a queue to await an ide ine. Whie on hook: Press HOLD. 0 0 Press ine button. Hear short tone. When ine is free, your teephone wi sound five short tone bursts teing you that you can use your ine. Intercom Cas Intercom cas may be diaed manuay or, using a programmed button (DSS), automaticay. To voice ca manuay, a Lift handset. 0 Press rtcm. 0 Dia extension number. 0 Tak. To voice ca automaticay (DSS), * Lift handset. Press DSS button. Tak. Continued on nexf page : : 1,::, 14

18 Intercom Cas (continued) To tone ca manuay, Lift handset. Press TCM. 0 Dia extension number. e Press 0 Tcy again. Caed teephone wi ring. NOTE: Some systems may be set up to tone signa as the first option. Pressing ITCM a second time is twt necessary in this case. To tone ca automaticay Lift handset. Press DSS button. Press 0 itcm. When intercom party answers, two-way conversation can take pace. Secure Off-Hook Voice Announce To make a voice announcement to another station that is off-hook or busy on a ca,.. Make intercom ca. o Hear severa quick tone bursts for a SOHVA. * Make announcement. When you hear a busy tone, this means the station is on the speakerphone and you cannot make an announcement. The person you are caing wi, however, hear a ring from his teephone. Wait on ine for repy. If announcing from an LCD speakerphone, caed station may send non-verba repy for dispay. As response is dispayed, the announcing station is disconnected. NOTE:.The caer cannot contro how the announcement is received. This depends upon the equipment used and cass of service programming. 15

19 Automatic Caback If the intercom station you have caed is busy, you can queue to the busy teephone. 1. Dia ( when you hear a busy signa Hang up. Your teephone wi ring with five short tone bursts when the one you caed becomes ide. After you ift the handset, the teephone you caed wi ring. If you don t ift the handset, the caback is canceed. To cance automatic caback before it rings: Hang up. Automatic Diaing (Autodia) This is one- or two-button diaing using programmabe buttons other than keypad buttons. To automaticay dia numbers, Press button programmed for desired number. If button is programmed on second eve (under DSS button), Press 0 HOLD and then press DSS button. Automatic Rediaing (Auto-Redia) If the ast number you have caed is busy or is not answering, use this feature. Once activated, it automaticay redias the number once a minute for 10 minutes. To activate automatic redia, Press button programmed for that purpose (that you have abeed auto-redia ). Number wi be diaed once a minute for 10 minutes. Continued on next page : ; : : -, 16

20 Automatic Rediaing (continued) If caed station is busy, * Press auto-redia button to begin rediacyce immediatey. (ITCM ight fashes.) To cance automatic redia, NOTE: Press auto-redia button and ift and repace handset, or press any station key. (ITCM ight goes out.) Using your teephone cances auto-redia. :.,:: Speed Diaing Speed diaing is autodiaing using the keypad buttons. Station numbers are persona numbers, i.e., business associates, trave agencies, etc., that are used ony by you. System numbers are pubic numbers, i.e., the corporate office, the company awyer, etc., that are accessed from every station. Make sure you have a ist of the system speed dia numbers. To speed dia station numbers if on-hook, Dia the keypad number (0 through 9) you have programmed into your teephone. ma If off-hook and on a ine, 0 0 Press OLD. * Press the keypad digit (0 through 9). To speed dia system numbers if on-hook, 0 Press a. 0 Dia the memory ocation numbers (01 through 99) you have programmed into the system. Em Continued on next page /. I. :: 17

21 Speed Diaing (continued) If off-hook and on a ine, Press OLD. 0. pus the memory ocation digits (01 through 99). i.:. I Last Number Rediaing The ast number diaed can be automaticay rediaed with a oneor two-button action. Press 0 #. (If on ine istening to dia tone, press 0 HOLD, then press 0 #.) Listen for ringing or busy tone. - Ringing tone: When party answers, pick up handset. - Busy tone: to disconnect. Saved Number Rediaing The first 16 digits of the ast manuay diaed number can be saved for ater redia. To save the number, Press button preprogrammed for this purpose. To dia a saved number, Lift handset. Press 0 OLD, then press preprogrammed button. NOTE: You can store ony one I6-digit number at a time. 18

22 i. -. :.... Manua Hod Hoding Cas To pace a ca on hod, 0 Press HoLD. To retrieve a hed ca, o Press ine button with fashing ight, or * Press 0 TAP if station does not have ine appearance. Excusive Hod This means that ony you can retrieve the hed ca on your teephone. To pace on excusive hod, e Press 0 HoLD twice. To retrieve excusive hod, o Press ine button with fashing ight. mu Press 0 TAP if station does not have ine appearance. Direct Station Hod (parking a ca to a station) To pace a ca on direct hod, 8 Whie on ine, press 0 rtcm. This paces the outside ca on hod. 8 pus the extension number of the station receiving park. To retrieve a direct hod ca, * From the hod receiving @. Continued on next page... 19

23 Direct Station Hod (continued) To cance a direct hod ca from station that paced ca on hod, Dia a@ p us extension number of the station hoding the ca. Doing this reconnects you to the outside Sine. i. T, I. Ca Park (parking a ca to an orbit) To park a ca in one of nine orbits, Whie on ine, Dia a park zone access code (91 through 99). To retrieve a parked ca, From any station, Dia the park zone access code (91 through 99). Hod Reca Feature After a preprogrammed ength of time, a ca paced on hod wi automaticay ring back to the teephone that paced it on hod. If the ca is on excusive hod, it wi revert to manua hod after the hod reca time period. The ca can then be retrieved by anyone with that ine appearance. E.. i-... i,..! : 20

24 Transferring Cas When transferring a ca you can either identify the caer before you transfer (screened) or you can transfer the ca without identifying the caer (unscreened). Screened Transfer To screen and transfer a ca to another station in the system, Answer ca. c Press e Cafe. Ca is paced on hod automaticay. Dia extension number of party to be transferred to. Eia Press DSS button for one-button intercom caing. 0 When intercom party answers, announce ca. Hang up handset. If the caed party is busy or does not answer, * Press ce3 CONF to retrieve ca. Unscreened Transfer To transfer an unscreened ca to another station in the system, Answer ca. Press e3 CONF. Ca is paced on hod automaticay. Dia extension number of party to be transferred to. ma Press DSS button for one-button intercom caing. Continued on next page.. 27

25 Unscreened Transfer (continued) Hang up handset. NOTE: If the station to which unscreened transfers are made is busy, the transjierred cas wi camp-on at the station. Each ca wi automaticay ring the station when it becomes ide. If a transferred ca is not answered after a preprogrammed time, it wi ring back to your station. Answer by pressing fashing ine key. 22

26 ., :.:( Making Conference Cas Five-Party Conference Cas You can make conference cas that encompass up to five parties, incuding you as the originating station, in any combination of outside ines and inside stations. For exampe, you can conference three outside ines and two inside stations or four outside ines and one inside station or five inside stations - the combinations are up to you. To set up a conference ca that incudes either outside ines and inside stations, or just inside stations, 1. Make first ca. 2. Press et3 CoNF. (Ca is paced on hod automaticay.) 3. Make next ca. 4. Press e CONF to estabish conference. 5. Repeat steps 2-4 to add up to two more parties. NOTE: When setting up a conference ca with outside ines and inside stations, you must ca the outside ines first. To continue conversation with ast conferee after three outside ines have dropped out of conference, Press the ine button of the remaining party. To drop outside ines from the conference, Press HOLD to put a ines on HOLD before the caer hangs up. Not doing this wi resut in a tone sounding in the handset receiver, interrupting the remaining conferees. To retrieve ines from HOLD and bring them back into the conference, repeat steps 1-5 above. NOTE: if a the corgference circuits are busy, you wi not be abe to add a party to the conference. The message Conference Fu wi appear in your dispay. 23

27 Unsupervised Conference Cu Dropping out of a conference ca and eaving outside ines in the conference is known as an unsupervised conference ca. You can do this ony when you are invoved in a three-party conference ca. To drop out of a conference ca, dia 0 # and hang up. NOTE: Conference voiume eves are dependent upon the quaity of the externa ines. 24

28 Message Waiting Light Messaging If your station has been designated as a centra message desk, you can turn on the message waiting ight (above HOLD) of any teephone from your station to et the user know that a message awaits pickup. To receive a message at an aerted station, Observe fashing ight. Lift handset. Connection to station that eft message is automatic. To turn on the message waiting ight, Dia extension number of station to be aerted. The message waiting ight of caed station wi fash. To turn off the message waiting ight, Dia extension number of station that was aerted. The message waiting ight of caed station wi turn off. To turn off the message waiting ight during message-deivering conversation, * Press WA. 0 NOTE: Any station, ifprogrammed with Message Wait Originate, can have this messaging capabiity. 25

29 LCD Messaging System-suppied messages can be set at a station to be received or dispayed by a caing LCD speakerphone. These messages give information on the status of the teephone user. In the back of this guide there is a ist entited LCD Messages. Fi it in after the attendant gives you the ist of messages. To turn on message, Dia the desired code number from your message ist. The defaut messages of Back At and Ca may be used: For defaut message 1, which is Back At, dia time in tweve-hour format using the # as a coon. For defaut message 2 which is Ca, dia teephone number of where you wi Intercom ight fashes steadiy. To turn off message and your intercom ight, Response Messaging when you receive a secure off-hook voice announce or an intercorn ca, this feature ets you send a message back to the caing station s LCD. The response messages are preprogrammed and stored at individua stations. You may send them by pressing a programmabe button designated for sending response messages. Get a ist of the messages from the attendant. NOTE: When you send a response message, the caing party wi be disconnected.! j 26

30 Station-To-Station Messaging When a station-to-station ca is made and no one answers, the caer may eave a message by activating the BLF ight at the caed station if the caing station is stored as a DSS /BLF at the caed station. To turn on message ight, Make intercom ca. If there is no answer: BLF ight at caed station turns on. To turn off message ight, Press@@@. Dia extension number of station to turn off message ight. To answer messaging, Press DSS associated with ighted BLF ight. If the caing station is not stored as a DSS at the caed station, then the ca wi transfer to the centra message desk, if programmed. Then the centra message desk (usuay the attendant s station) can ight the message waiting ight of the originay caed station. Assist Button Messaging By using a programmed assist button on your teephone, you can send a message to your supervisor, asking for assistance. To send a message for assistance, Press ASSIST button. If you have not programmed the extension number of the station you need hep from, press the DSS button that is assigned to that station after pressing the ASSIST button If assisting station is ide, tone burst sounds and message appears in dispay. If it is busy, message appears when it becomes ide. 27

31 Programming Your Teephone Autodia Programming Autodia is a feature that ets you: Dia engthy numbers using one or two buttons. Store frequenty used feature codes. Autodia can be stored: At a bank programmabe button, or On a secondary eve under a DSS button. Before you begin programming, write down: The ine(s) you wi use to access the number. The number or feature code you are storing. As you program numbers, fi in the identification strips on your teephone. Write first eve numbers on the ID strips and secondary numbers on the index puout directory in the front of your teephone. Because the programming steps for outside numbers, intercom numbers and feature codes vary sighty, they appear here as separate steps. Prdgramming Outside Numbers Press programmabe button you want for storage. 3. Press your ine button or 0 (for ast ine used or prime ine, if assigned). 4. Dia the numbers to be stored: * You can enter up to 16 digits. A digits on the keypad are vaid. You may need a pause between numbers to compensate for differences in response time between your system and the host system. If you do, press the H9LD button to insert a pause. Then, continue diaing continued on next page. 29

32 Autodia Programming (continued) Programming Outside Numbers (continued) If your system is behind a host system that needs a hookfash to access a feature, press the TAP button. Then, continue diaing. 5. To continue storing, press the TFUNS/CONF button and repeat steps to end. You can store an autodia number under a DSS button. Just repeat steps 1-6, using the programmabe button mentioned in step 2. Programming Outside Numbers Using Line Groups Line groups are represented as 1,2,3, and 4 on the keypad. The tabe beow shows the ine group and its corresponding keypad number. To store a number using a ine group: Press programmabe button you want for storage. 3. Press either 1 (9), 2 (81), 3 (82), or 4 (83) on the keypad. 4. Dia the number you are storing. 5. To store another number, press the TRANS/CONP button and repeat steps to end. Confinued on nexf page 30

33 Autodia Programming (continued) Programming Intercom Numbers (DSS/BLF) Press the DSS button you want for storage. Dia the intercom number to be stored. To store another number, repeat steps 2 and Programming Feature Codes For convenience and quick access, you might want to store feature codes. Some exampes of these are: Ca Forwarding (on and off). CaPickup Automatic Rediaing To program feature codes, 1. Press@aaQJ. 2. Press programmabe button you are using for storage. 3. Enter the codes for the feature. Exampe: For Ca Forwarding to a specific extension, press@a@@ andextension of teephone you want cas forwarded to. 4. To store another code, press the TRANSKONF button and repeat steps 2 and Press@ end. NOTE: See Quick Reference Guide in back of this guide for compete feature code isting. 31

34 Station Speed Dia Programming Using the keypad digits, you may store frequenty used teephone numbers that ony you wi access. Before you begin, make a ist Of: 0 The storage ocation you are using (0 through 9 on the keypad). The ine the ca wi go over. The teephone numbers or feature codes you are storing. Use the directory in the puout index tray in front of your teephone to store the ist. To program station speed dia numbers,. 1. cir ) 2. Press a keypad button (0 through 9) that you are using for storage. 3. Choose the ine to be used: - 0 = ast ine used or prime ine (if assigned) - ine key - ITCM = intercom - 1 through 4 = ine groups 4. Dia the number to be stored (up to 16 digits); if you need a pause between numbers, press the HOLD button. 5. Press e3 =onf to continue entering numbers. 6. end. i Response Message Programming This program ets you set up a button to be used for making a non-verba response to a SOHVA or an intercom ca. The response appears in the dispay of the caing station. To assign a button for non-verba response: 2. Press the programmabe button you want to use for message access. Continued on next page 32

35 Response Message Programming (continued) Dia a message number (0 through 9). NOTE: The preprogrammed messages are created by the attendant. 5. end. Automatic Redia Programming To program a button on your teephone for rediaing cas you make that are either busv or do not answer, 1. Press@@aa. 2. Press programmabe button. 3. Press 0 #. 4. Press@ end. When you push this programmed button after having made a ca that is busy or doesn t answer, the system wi automaticay dia the number every minute for 10 minutes and ring the number for approximatey 30 seconds. To cance auto-redia, simpy ift and repace the handset. Assist Button Programming With this feature you can program an assist button on your teephone that wi et you send a message to an LCD speakerphone. By pushing this button you can et your supervisor know, with a tone and a station message dispay, that you need assistance with a probem caer. Then, after receiving the tone and the dispay message, your supervisor can join the ca or monitor it through executive override or service observing. Continued on next page... 33

36 Assist Button Programming (continued) II 2.. To program an assist button, Press programmabe button you want as assist button. Dia 0-9 to choose preprogrammed message. (See attendant for ist of messages.) Dia a to choose system-provided message. (System message = ASSIST pus name or extension number of station sending message. Name or extension is automaticay added by system.) If one particuar station must aways receive message, dia extension number of that station; otherwise, skip to step 6. Labe button. to end. j j 34

37 : Using Misceaneous Features Account Code Entry If you need to enter an account code for the SMDA report whie caing a number, you can do so using this feature. However, code entry is vountary, i.e. if you do not enter a code, the ca wi continue to go through. To enter account code: Seect ine. The dispay on the LCD speakerphones wi prompt for Account Code if programmed to do so. Press@@@@. Dia account code. Listen for dia tone. Dia number you are caing. NOTE: If you hear an error tone after step 3, check the account code for vaidity. j:. Automatic Set Reocation With this feature, if you move your teephone to another ocation, you wi be given a choice via the dispay prompt as to whether you want to keep the previous programming or use the programming in the new ocation. Background Music If suppied by your system, music can be set to pay through your teephone speaker. To turn music ON: 1. a a. Speakeright witumon 2. Adjust oudness of music with speaker voume contro. To turn music a. Speaker ight wi turn off. NOTE: Background music automaticay turns off during cas. : i. ; :. ::. 35

38 Ca Forwarding You can forward your cas to ring at another station. To forward intercom and prime ine cas to another teephone: Dia extension number of teephone to which cas are to be forwarded. 3. Hang up. To cance intercom and prime ine ca forwarding: andhangup. To forward a cas to another teephone: Dia extension number of teephone to which cas are to be forwarded. 3. Hang up. To cance a ca forwarding: Press@= (5;;> andhangup. NOTE: Your station wi ring with a short ring burst each time a ca is forwarded to remind you that your cas are being forwarded. Ca Override Features Executive Override If your teephone has this feature, you can break into a conversation at another station. When you make an intercom ca and hear a busy signa: 1. Severa short tone bursts wi sound at the caed station. 2. Join in-progress ca. Continued on next page. 36

39 Ca Override Features (continued) Service Observing For training purposes, this feature aows you, undetected, to monitor a conversation at another station. You can use this feature on-hook or off-hook. To monitor an in-progress ca: 2. Dia extension number of station you are going to monitor. 3. or@ to end..: Ca Waiting You can send a ca waiting tone to a busy station and wait for an answer. To activate ca waiting: 1. Make intercom ca and hear busy signa. 2. Dia Caed party wi hear tone. 3. Remain on ine, waiting for caed party response. To cance ca waiting, hang up handset. To answer ca waiting if you receive a ca waiting tone whie on a ca: 1. Hear short tone burst in receiver. 2. Either pace ca on hod or compete present ca and hang up. Waiting ca wi begin ringing. 3. Lift handseto answer. Departmenta Station Operation If your station is within a departmenta group of stations, you can pace your station in either an off-duty or a wrap-up mode. Off-duty mode is when you eave your station for unch or for an extended time period. Continued on next page... 37

40 Departmenta Station Operation (continued) To pace station in off-duty mode, press Do-Not-Disturb (DND) button. Cas wi ring at another departmenta station. To return to on-duty mode, press DND again. Wrap-up mode is when you may need time after a ca to perform paperwork, but you stay at your station. o To pace station in wrap-up mode, press HOLD DND buttons. Cas wi ring at another departmenta station. To return to on-duty mode, press HOLD DND again. * / Dispay Contrast Adjustment If your teephone has an LCD, you can adjust the contrast of the dispay by hoding down the MUTE button on your teephone. After five seconds, Contrast Leve and a number shows up in the dispay. Continue to depress the MUTE button; the dispay contrast changes. The numbers 0 through 7 representhe contrast from ight (0) to dark (7). When you have adjusted the dispay contrast to suit you, reease the MUTE button. Do Not Disturb This feature keeps cas from ringing at your station and makes your station appear to be busy to intercom cas. If your teephone has this feature, press the button arranged by cass of service programming for this purpose. The ight associated with this feature wi turn on when you are using Do Not Disturb. To cance this feature, press the button again. NOTE: Generay, this feature cannot be overridden by the caer; the caer wi hear two quick tone bursts every three seconds. Some stations, however, have the abiity to override Do Not Disturb. 38

41 Mute Button By using the MUTE button, you can bock transmission of your voice to the distant party. For exampe, if someone comes into your office to tak to you and you do not want to interrupt the distant party, just press the MUTE button. The MUTE button turns on and ocks when you press it and turns off when you press it again. Paging If you have an externa paging unit set up by the instaer, you can page over it: 1. Lift handset Dia paging access number, push ine button (if externa paging is on a ine) or, if hooked up to auxiiary paging port, Make announcement, 4. Hang up. You can aso page a stations through their intercoms (a-ca paging) or just some stations (zone paging). To do this: 1. Lift handset Press TCH. 3. Dia 87 for a-ca paging. Dia 84, 85, or 86 for zone paging. 4. Make announcement and stay on ine if waiting for an answer. 5. Hang up handset. You can answer an a-ca or zone page from any station in the system. To answer this page known as Meet-Me Page : 1. Lift handset of nearest station. 39

42 Persona Ringing Tones You can choose one of four different ring tones to easiy identify your station when it rings. To seect one of these rings: One of four ringing tones wi be seected and the next time your teephone rings, you wi hear the difference. Privacy By pressing a button designated a privacy button, you can aow another person to join you in a ca. This feature is preprogrammed by the instaer. Puse/Tone Switching If your oca teephone service is puse rotary), but you have to convert to tone whie diaing, press # b at the point in the diaing sequence where conversion to tone is required. The system wi switch back to puse diaing when you end your ca. You can program puse-to-tone switching by pressing 0 8 during autodia or speed dia number storage. Voice Announce Bocking You can prevent voice-signaed intercom cas from sounding through your station speaker. To bock voice cas: To un-bock voice cas: This feature aso bocks Secure Off-Hook Voice Announce cas. 40

43 , I A Grwpz,TCM 31 omup3 I ITCM 32

44 Tabe 2. Dispay Summary 91 Automatic Caback This preprogrammed message appears in dispay that it is sent to. Either a name or a station number can be entered. I Automatic Redia Dispay shows that feature is ac- -1 tive. Ca Costing When you push HOLD button Ca Forward Ca Messaging dispay. Dispay shows extension number of teephone to which ca is for- Dispay prompts for message. Entering a keypad digit (O-9) causes a message to be dispayed. 42

45 Tabe 2. Dispay Summary (continued) Dispay Type Ca Timer -1 Caing Station When Dispayed Begins during diaing and dispays for 10 seconds after hang-up. To reca dispay for ast competed ca, press HOLD key. The dispay shows extension number or name of caing teephone. 1 Conference Cas -1-1 When conferencing with ines, this shows up in dispay. When conferencing with other sta- Diaed Numbers c diaed codes. The dispay wi show a numbers or names aong with any Station: 1:,,1 E Er%;p ~q-igm A ccess Codes: wi show ub in the bottom I 43 I

46 Tabe 2. Dispay Summary (continued) Dispay Type When Dispayed 1 Dispay Contrast Adjustment v Dispay after hoding down Mute bu?f f;rfvueg.yds. Do Not Disturb -1 Dispay shows Do Not Disturb when feature is active. Hod Reca Feature When a timed hod reca occurs, Last Number When ast number diaed is redaed, dispay shows seected ine 9 and diaed number. Line Queuing 44

47 Tabe 2. Dispay Summary (continued) Dispay Type Line Seection FTII Mute jtue1 When Dispayed When ine is seected for cahing or when ringing ine is answered. Lines can be programmed to dispay numbers or names, i.e. WATS. Dispay shows when feature is active. paging (paging Dispay for a-ca page (paging Programming for Autodiaing and Station Speed Diaing v VI After you press ITCM +k S 1, this appears in the dispay. After you enter ocation, this appears in dispay. v After you enter ine, this appears in dispay. Dispay after you dia the number. 45

48 Tabe 2. Dispay Summary (continued) Dispay Type When Dispayed Saved Number Redia -1 Service Observing rpi%igq Station Identification mpyy When a number is saved, dispay shows that feature is active. When saved number is diaed, dispay shows seected ine, then shows diaed number. When using service observing, the names or extension numbers of two stations show up in dispay. Pressing SPKR or MNTR when your station is ide causes your extension number, port number and station name to show up in the dispay. X = extension number Y = port number Z = station name System Cock And Caendar Aways dispayed as top ine of 77 dispay. NOTE: Date and time are set by attendant as part of system programming. 46

49 A Gossary A-ca paging: Paging through the intercoms of a stations in the system. Assist button: A button that you can program that wi et you send a message requesting assistance to the LCD of another teephone. Automatic caback: System wi ring a caing teephone when a busy caed teephone becomes ide. Automatic diaing (or Autodiaing): Using programmabe buttons to store numbers for one- or two-button diaing. Automatic rediaing: Turning on a program that automaticay red& the ast number diaed once a minute for 10 minutes. C Ca forward: Designating another teephone to receive intercom cas normay directed to the user s teephone. Ca park: Pacing an active ca at a particuar teephone in system hod (park orbit) and retrieving it by any teephone. Ca pickup: Answering a ca at one teephone when it is ringing at another teephone. Ca transfer: Transferring a ca from one station to another. The-transfer can be screened, i.e., you find out who is caing and announce them to the party being caed; or unscreened, i.e., you transfer the ca without identifying the caing party to the caed pafy. Centra message desk: A station that has been assigned to contro message waiting ights and deiver messages to other stations in the system. Cass of Service programming: Customized programming of your system by the instaer that estabishes the basic operating parameters of the system and individua stations. D Departmenta station operation: The operation of stations that are organized into departments. Direct Inward Station Diaing (DISD): This feature aows an outside party to ca an intercom station directy without an attendant s assistance. 47

50 E K L Direct Station Seection/Busy Lamp Fied (DSSBLF): Using one button to pace intercom cas; the button is sometimes referred to as a DSS button. Busy amp fied or BLF is a term for a ight that identifies current ca status of DSS station. Do not disturb: A mode that disabes incoming ca ringing and intercom caing. M Dua Tone Mutipe Frequency (DTMF): The tones made by your teephone when you dia. Dynamic ine key: System temporariy assigns a normay unassigned ine to an ide ine button for certain ca handing operations. Excusive hod: Ony the teephone pacing the ca on hod can retrieve it. Executive override: Breaking into a conversation at a busy caed teephone. This intrusion is announced by severa quick tone bursts over the conversation. H Handsfree answer inhibit: A teephone can be set to bock voice cas sent to it over the speaker. Hookfash: Action that occurs when the TAP button is pressed. Needed for activating host system features. Hookswitch: The switch on a teephone which, when depressed manuay or by the handset, disconnects a ca. Keypad: Buttons 0 through 9, Jc and # used for diaing numbers. Last number rediaing: Automaticay diaing the ast number diaed. Messaging: Turning on a teephone amp to et the user know that amessage awaits pickup and eaving a message on the dispay of a teephone that gives information on your status. Mute: A fixed feature button that keeps a distant party from hearing your conversation. This button aso ets you adjust the teephone dispay contrast from ight to dark. 48

51 N P Night transfer: Transferring incoming cas to a particuar station(s) for off-hour answering. Persona ringing tones: A teephone can be arranged to ring in one of four distinctive tones. Prime ine: A ine designated to a particuar teephone and automaticay seected when the handset is ifted. Programmabe buttons: Each teephone or station has buttons that can be user-programmed for autodiaing numbers or feature codes, or other specia purpose diaing requirements. Puse/Tone switching: Changing from puse/rotary dia signas to tone/dtmf signas. R S Response messaging: Responding non-verbay to a caing station by pressing a programmed button that sends a message to the caing station s dispay. Ringing ine preference: An automatic connection to any outside ine ringing at the station when the station handset is taken off-hook. Saved number rediaing: Saving a ast manuay diaed number for ater autodiaing. Secure off-hook voice announce: A private announcementhat can be made to a busy party which they hear through the receiver of their handset. Speed diaing: Autodiaing using the keypad buttons. Speed diaing can be station cas (persona and accessed by ony one specific user) or system cas (numbers used and accessed by anyone in the system). T TAP: Depending on your system s programming, this button gives you a fresh dia tone or activates a hookfash. Tone ca: A ringing intercom ca. Trans/Confi A fixed feature button that aows you to transfer outside cas and set up conference cas. 49

52 V Z Voice ca: A verba intercom ca. Voice announce bocking: A teephone can be set to bock voice cas sent to it over the speaker. Zone paging: Paging through the intercoms of some stations or departments in the system. 50

53 Index A B Account code entry 35 A-ca paging 39 Answering cas Intercom 9 Night transfer 10 Outside 9 Pages 39 Secure off-hook voice announce 10 Assist button Programming 33 Using 27 Automatic caback 16 Automatic diaing Programming 29 Using 16 Automatic set reocation 35 Background music 35 c,. D Ca forwarding 36 Ca override features 36 Ca park 20 Ca pickup 9 Ca waiting 37 Conference cas Five-party cas 23 Unsupervised cas 24 Departmenta station operation 37 Direct station hod 19 51

54 E H I L M Dispay contrast adjustment 38 Do not disturb 38 Excusive hod 19 Executive override 36 Hod reca 20 Hoding cas Ca park 20 Direct station hod 19 Excusive hod 19 Manua hod 19 Intercom cas Answering 9 Making 14 Programming numbers 31 Last number rediaing 18 LCD messaging Turning off 26 Turning on 26 Making cas Conference 23 Intercom 14 Outside 13 Secure off-hook voice announce 15 Manua hod 19 Message waiting ight Receiving message 25 Turning off 25 Turning on 25 52

55 N 0 P Q Messaging LCD 26 Response 26 Station-to-station 27 Mute button 38 Night transfer Answering 10 Outside cas Answering 9 Making 13 Programming numbers 29 Paging A-ca 39 Answering ( Meet-me ) 39 Over PA system 39 Zone 39 Persona Ringing Tones 40 Privacy 40 Programming Assist button 33 Autodia numbers 29 Automatic rediaing 33 Feature codes 31 Intercom numbers 3 1 Outside numbers 29 Response messaging 32 Station speed dia numbers 32 Puse/Tone switching 40 Queuing Busy ine queuing 14 Line group queuing 13 Quick reference guide 41 53

56 R S T V z Response messaging Programming 32 Using 26 Ringing tones, persona 40 Saved number rediaing using 18 Secure off-hook voice announce (SOHVA) Making 15 Responding to 10 Service observing 37 Speakerphone operation 6 Speed diaing Programming 32 Station 17 System 17 Station speed dia programming 32 Station-to-station messaging Turning off 27 Turning on 27 Transferring cas Screened transfer 21 Unscreened transfer 21 Voice announce bocking 40 Zone paging 39 54