RX-495/395. Natural Sound Stereo Receiver Ampli-syntoniseur stéréo de la série Natural Sound Receptor estéreo de Sonido Natural

Transcription

1 RX-95/95 Natura Sound Stereo Receiver Ampi-syntoniseur stéréo de a série Natura Sound Receptor estéreo de Sonido Natura Thank you for seecting this YAMAHA stereo receiver. Nous vous remercions pour avoir porté votre choix sur ce récepteur stéréo YAMAHA. Muchas gracias por haber adquirido este receptor estéreo YAMAHA. OWNER S MANUAL MODE D EMPLOI MANUAL DE INSTRUCCIONES

2 SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Expanation of Graphica Symbos The ightning fash with arrowhead symbo, within an equiatera triange, is intended to aert you to the presence of uninsuated dangerous votage within the product s encosure that may be of sufficient magnitude to constitute a risk of eectric shock to persons. The excamation point within an equiatera triange is intended to aert you to the presence of important operating and maintenance (servicing) instructions in the iterature accompanying the appiance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1 Read Instructions A the safety and operating instructions shoud be read before the unit is operated. Retain Instructions The safety and operating instructions shoud be retained for future reference. Heed Warnings A warnings on the unit and in the operating instructions shoud be adhered to. Foow Instructions A operating and other instructions shoud be foowed. 5 Water and Moisture The unit shoud not be used near water for exampe, near a bathtub, washbow, kitchen sink, aundry tub, in a wet basement, or near a swimming poo, etc. 6 Carts and Stands The unit shoud be used ony with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination shoud be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 Wa or Ceiing Mounting The unit shoud be mounted to a wa or ceiing ony as recommended by the manufacturer. 8 Ventiation The unit shoud be situated so that its ocation or position does not interfere with its proper ventiation. For exampe, the unit shoud not be situated on a bed, sofa, rug, or simiar surface, that may bock the ventiation openings; or paced in a buit-in instaation, such as a bookcase or cabinet that may impede the fow of air through the ventiation openings. 9 Heat The unit shoud be situated away from heat sources such as radiators, stoves, or other appiances that produce heat. 10 Power Sources The unit shoud be connected to a power suppy ony of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection Power-suppy cords shoud be routed so that they are not ikey to be waked on or pinched by items paced upon or against them, paying particuar attention to cords at pugs, convenience receptaces, and the point where they exit from the unit. 1 Ceaning The unit shoud be ceaned ony as recommended by the manufacturer. 1 Nonuse Periods The power cord of the unit shoud be unpugged from the outet when eft unused for a ong period of time. 1 Object and Liquid Entry Care shoud be taken so that objects do not fa into and iquids are not spied into the inside of the unit. 15 Damage Requiring Service The unit shoud be serviced by quaified service personne when: A. The power-suppy cord or the pug has been damaged; or B. Objects have faen, or iquid has been spied into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normay or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing The user shoud not attempt to service the unit beyond those means described in the operating instructions. A other servicing shoud be referred to quaified service personne. 17 Power Lines An outdoor antenna shoud be ocated away from power ines. 18 Grounding or Poarization Precautions shoud be taken so that the grounding or poarization is not defeated.

3 19 For US customers ony: Outdoor Antenna Grounding If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against votage surges and buit-up static charges. Artice 810 of the Nationa Eectrica Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the ead-in wire to an antenna discharge unit, size of grounding conductors, ocation of antenna discharge unit, connection to grounding eectrodes, and requirements for the grounding eectrode. EXAMPLE OF ANTENNA GROUNDING MAST GROUND CLAMP ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810 0) Engish Note to CATV system instaer: This reminder is provided to ca the CATV system instaer s attention to Artice 80-0 of the NEC that provides guideines for proper grounding and, in particuar, specifies that the cabe ground sha be connected to the grounding system of the buiding, as cose to the point of cabe entry as practica. ELECTRIC SERVICE EQUIPMENT NEC NATIONAL ELECTRICAL CODE GROUNDING CONDUCTORS (NEC SECTION 810 1) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 50. PART H) SPECIAL NOTES FOR FCC COMPOSITE DEVICE (for US customers ony) This device is a composite system. The digita device component may not cause harmfu interference. FCC INFORMATION (for US customers ony) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when instaed as indicated in the instructions contained in this manua, meets FCC requirements. Modifications not expressy approved by Yamaha may void your authority, granted by the FCC, to use the product.. IMPORTANT : When connecting this product to accessories and/or another product use ony high quaity shieded cabes. Cabe/s suppied with this product MUST be used. Foow a instaation instructions. Faiure to foow instructions coud void your FCC authorization to use this product in the USA.. NOTE : This product has been tested and found to compy with the requirements isted in FCC Reguations, Part 15 for Cass B digita devices. Compiance with these requirements provides a reasonabe eve of assurance that your use of this product in a residentia environment wi not resut in harmfu interference with other eectronic devices. This equipment generates/uses radio frequencies and, if not instaed and used according to the instructions found in the users manua, may cause interference harmfu to the operation of other eectronic devices. Compiance with FCC reguations does not guarantee that interference wi not occur in a instaations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, pease try to eiminate the probem by using one of the foowing measures: Reocate either this product or the device that is being affected by the interference. Utiize power outets that are on different branch (circuit breaker or fuse) circuits or insta AC ine fiter/s. In the case of radio or TV interference, reocate/reorient the antenna. If the antenna ead-in is 00 ohm ribbon ead, change the ead-in to coaxia type cabe. If these corrective measures do not produce satisfactory resuts, pease contact the oca retaier authorized to distribute this type of product. If you can not ocate the appropriate retaier, pease contact Yamaha Eectronics Corp., U.S.A Orangethorpe Ave, Buena Park, CA The above statements appy ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime (for US customers ony) YAMAHA and the Eectronic Industries Association s Consumer Eectronics Group want you to get the most out of your equipment by paying it at a safe eve. One that ets the sound come through oud and cear without annoying baring or distortion and, most importanty, without affecting your sensitive hearing. Since hearing damage from oud sounds is often undetectabe unti it is too ate, YAMAHA and the Eectronic Industries Association s Consumer Eectronics Group recommend you to avoid proonged exposure from excessive voume eves.

4 FEATURES RX-95 70W + 70W (8Ω) RMS Output Power, 0.0% THD, 0 0,000 Hz RX-95 5W + 5W (8Ω) RMS Output Power, 0.0% THD, 0 0,000 Hz High Dynamic Power, Low Impedance Drive Capabiity Continuousy Variabe Loudness Contro 0-Station Random Access Preset Tuning Automatic Preset Tuning Preset Station Shifting Capabiity (Preset Editing) IF Count Direct PLL Synthesizer Tuning System SLEEP Timer Remote Contro Capabiity RX-95 ony PURE DIRECT Switch to Reproduce the Purest Source Sound CONTENTS Safety Instructions... Features... Suppied Accessories... Caution... 5 Contros and Their Functions... 6 Connections Basic Operations... 1 Tuning Operations Preset Tuning Notes about the Remote Contro Transmitter... 1 Troubeshooting... Specifications... SUPPLIED ACCESSORIES After unpacking, check that the foowing parts are contained. Remote Contro Transmitter Indoor FM Antenna AM Loop Antenna RX-95 RX-95 Batteries (size AA, R6, UM-) Antenna adapter <U.S.A. and Canada mode ony>

5 CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, pease read this manua carefuy. Keep it in a safe pace for future reference. Insta this unit in a coo, dry, cean pace away from windows, heat sources, sources of excessive vibration, dust, moisture and cod. Avoid sources of humming (transformers, motors). To prevent fire or eectrica shock, do not expose the unit to rain or water. Do not operate the unit upside-down. It may overheat, possiby causing damage. Never open the cabinet. If something drops into the set, contact your deaer. IMPORTANT Pease record the seria number of this unit in the space beow. Seria No.: The seria number is ocated on the rear of the unit. Retain this Owner s Manua in a safe pace for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Engish 5 The openings on the cabinet assure proper ventiation of the unit. If these openings are obstructed, the temperature inside the cabinet wi rise rapidy. Therefore, avoid pacing objects against these openings, and insta the unit in we-ventiated condition. Make sure to aow a space of at east 10 cm behind, on the both sides and above the top pane of the unit. Otherwise it may not ony damage the unit, but aso cause fire. 6 Do not use force on switches, contros or connection wires. When moving the unit, first disconnect the power pug and the wires connected to other equipment. Never pu the wires themseves. 7 Do not attempt to cean the unit with chemica sovents; this might damage the finish. Use a cean, dry coth. 8 Aways set the VOLUME contro to before starting the audio source pay. Increase the voume graduay to an appropriate eve after the pay back has been started. 9 To prevent ightning damage, pu out the power cord and remove the antenna cabe during an eectrica storm. CAUTION (FOR CANADA MODEL) TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT. FOR CANADIAN CUSTOMER THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS. The apparatus is not disconnected from the AC power source as ong as it is connected to the wa outet, even if the apparatus itsef is turned off. FREQUENCY STEP switch (Genera Mode ony) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (ocated at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power pug of this unit from the AC outet. 10 Be sure to read the TROUBLESHOOTING section regarding common operating errors before concuding that the unit is fauty. 11 AC outet Do not connect audio equipment to the AC outet on the rear pane if that equipment requires more power than the outet is rated to provide. 1 Votage Seector (Genera Mode ony) The votage seector on the rear pane of this unit must be set for your oca main votage BEFORE pugging into the AC main suppy. Votages are /0 0V AC, 50/60 Hz. 5

6 FRONT PANEL RX-95 CONTROLS AND THEIR FUNCTIONS NATURAL SOUND STEREO RECEIVER TUNER CD POWER PRESET AM FM TAPE MONITOR 1 STEREO MHz MONITOR TAPE TAPE 1 AUX PHONO PURE DIRECT MEMORY ENTER AUTO TUNING SLEEP COPY PRESET STATIONS A/B/C/D/E 1 VOLUME TUNING MODE AUTO/MAN'L MONO FM/AM DOWN TUNING UP EDIT MEMORY MAN'L/AUTO FM PHONES SPEAKERS A B ON ON OFF OFF BASS 0 TREBLE 0 BALANCE 0 LOUDNESS FLAT -0dB I db L 5 5 R A B C D EF G H RX NATURAL SOUND STEREO RECEIVER TUNER CD POWER PRESET AM FM TAPE MONITOR 1 STEREO MHz TAPE MONITOR AUX PHONO MEMORY ENTER AUTO TUNING SLEEP PRESET STATIONS A/B/C/D/E 1 VOLUME TUNING MODE AUTO/MAN'L MONO FM/AM DOWN TUNING UP EDIT MEMORY MAN'L/AUTO FM PHONES SPEAKERS A B ON ON OFF OFF BASS 0 TREBLE 0 BALANCE 0 LOUDNESS FLAT -0dB I db L 5 5 R A B C D EF G H 6

7 1 POWER switch Press this switch to switch the power on. Press it again to switch the power off. * Standby mode <Austraia and Singapore modes ony> Whie the power is on, pressing the POWER key on the remote contro transmitter switches the unit to the standby mode. (In this mode, the power indicator is haf iuminated.) Remote contro sensor Receives signas from the remote contro transmitter. Dispay pane Shows station frequencies and various information. (Refer to the next page for detais.) FM/AM buttons Press this button to switch the reception band to FM or AM. 5 TUNING DOWN/UP button Used for tuning. Press the UP side to tune in to higher frequencies, and press the DOWN side to tune in to ower frequencies. 6 EDIT button This button is used to exchange the paces of two preset stations with each other. 7 MEMORY (MAN L/AUTO FM) button When this button is pressed, the MEMORY indicator fashes for about 5 seconds. During this period, press the desired PRESET STATIONS button to enter the dispayed station into the memory. When this button is pressed and hoded for about seconds, the automatic preset tuning begins. 8 Input seector buttons Seect a program source to isten to. When a button is pressed, the name of seected source ights up on the dispay. 9 PURE DIRECT switch RX-95 ony Press this switch to isten to a source in the purest sound. (Refer to page 16 for detais.) A SPEAKERS switches Set the switch A or B (or both A and B) for the speaker system (connected to this unit) you wi use to the ON position. Set the switch for the speaker system you wi not use to the OFF position. B TUNING MODE (AUTO/MAN L) button Press this button to switch the tuning mode to automatic or manua. To seect the automatic tuning mode, press this button so that AUTO TUNING ights up on the dispay. To seect the manua tuning mode, press this button so that AUTO TUNING goes off. C Tone contros BASS Used to increase or decrease the ow frequency response. The 0 position produces fat response. TREBLE Used to increase or decrease the high frequency response. The 0 position produces fat response. D BALANCE contro Adjusts the baance of the output voume to the eft and right speakers to compensate for sound imbaance caused by speaker ocation or istening room conditions. E A/B/C/D/E button Press this button to seect a desired group (A E) of preset stations. F PRESET STATIONS buttons Used to enter as many as 0 station frequencies into the memory. G Continuousy variabe LOUDNESS contro Used to compensate for the human ears oss of sensitivity to high and ow-frequency ranges at ow voume. H VOLUME contro Used to raise or ower the voume eve. Engish 0 PHONES jack When you isten with headphones, connect the headphones to the PHONES jack. When istening with headphones privatey, set both the SPEAKERS A and B switches to the OFF position. PHONES 7

8 DISPLAY PANEL 1 PRESET STEREO FM MHz MEMORY TAPE MONITOR AUTO TUNING SLEEP RX-95 RX-95 TAPE MONITOR TAPE MONITOR 1 1 Muti-information dispay Dispays various information, for exampe station frequency, preset station number and name of seected program source. STEREO indicator Lights up when an FM stereo broadcast with sufficient signa strength is received. Signa-eve meter Indicates the signa eve of the received station. If mutipath interfernce is detected, the indication decreases. MEMORY indicator When the MEMORY button is pressed, this indicator fashes for about 5 seconds. During this period, the dispayed station can be programmed to the memory by using the A/B/C/D/E button and one of the PRESET STATIONS buttons. 5 TAPE MONITOR indicator RX-95 Lights up when the tape deck is seected as the input source by pressing the TAPE MONITOR button. RX-95 When the first tape deck is seected as the input source by pressing the TAPE 1 button, TAPE MONITOR 1 ights up, and when the second tape deck is seected by pressing the TAPE button, TAPE MONITOR ights up. 6 AUTO TUNING indicator This indicator ights up when this unit is in the automatic tuning mode. 7 SLEEP indicator Lights up whie the buit-in SLEEP timer is functioning. 8

9 REMOTE CONTROL TRANSMITTER Engish The remote contro transmitter provided with this unit is designed to contro a the most commony used functions of the unit. If the CD payer and tape deck connected to this unit are YAMAHA components designed for remote contro compatibiity, then this remote contro transmitter wi aso contro various functions of each component. For Contro of This Unit 5 RX-95 TAPE RX-95 TAPE TAPE 1 1 Tuner keys Contros tuner. +: Seects higher preset station number. : Seects ower preset station number. A/B/C/D/E Seects the group (A E) of preset station numbers. SLEEP timer key The power to this unit is automaticay turned off one hour after this key is pressed (so that SLEEP ights up on the dispay). 1 1 YAMAHA HIFI SYSTEM REMOTE CONTROL TRANSMITTER DIR A DIR B REC/PAUSE PRESET + SLEEP POWER DISC PLAY A/B/C/D/E PLAY VOLUME A/B AUX TUNER CD PHONO 5 POWER key Turns the power on/off. * <Austraia and Singapore modes ony> Whie the power is on, pressing the POWER key on the remote contro transmitter switches the unit from the power-on mode to the standby mode, and vice versa. (In the standby mode, the power indicator on the front pane is haf iuminated.) VOLUME +/ keys Turns the voume eve up/down. 5 Input seector keys Seects input source. For Other Component Contro Identify the remote contro transmitter keys with your component s keys. If these keys are identica, their functions wi be the same. On each key function, refer to the corresponding instruction on your component s manua. 1 Tape deck keys Contros tape deck. * DIR A, B and A/B are appicabe ony to doube cassette tape deck. * For a singe cassette deck with automatic reverse function, pressing DIR A wi reverse the direction of tape running. CD payer keys Contros compact disc payer. * DISC is appicabe ony to compact disc changer. 9

10 CONNECTIONS Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure a connections are made correcty, that is to say L (eft) to L, R (right) to R, + to + and to. Aso, refer to the owner s manua for each component to be connected to this unit. * If you have YAMAHA components numbered as 1,,, etc. on the rear pane, connections can be made easiy by making sure to connect the output (or input) terminas of each component to the same-numbered terminas of this unit. RX-95 Turntabe Tape deck 1 Tape deck Speakers A OUTPUT GND LINE OUT LINE IN LINE OUT LINE IN Right Left (U.S.A. mode) GND FM ANT 75Ω UNBAL. SPEAKERS AC OUTLETS GND SWITCHED I0V 60Hz I00W MAX. TOTAL AM ANT or 5 or 6 TAPE REC TAPE REC PB OUT PB OUT A B PHONO CD 1 AUX TAPE 1 TAPE A OR B: 6ΩMIN./SPEAKER A B : ΩMIN./SPEAKER OUTPUT To AC outet AUDIO OUT Compact disc payer Video cassette payer, LD payer, etc. Right Speakers B Left : Refer to ABOUT THE ACCESSORY TERMINALS on page 1. 10

11 Engish RX-95 Turntabe Tape deck Speakers A OUTPUT GND LINE OUT LINE IN Right Left (U.S.A. mode) GND FM ANT 75Ω UNBAL. SPEAKERS AC OUTLETS GND SWITCHED I0V 60Hz I00W MAX. TOTAL AM ANT or 5 or 6 TAPE REC PB OUT A B PHONO CD 1 AUX TAPE A OR B : 6ΩMIN./SPEAKER A B : ΩMIN./SPEAKER To AC outet OUTPUT AUDIO OUT Compact disc payer Video cassette payer, LD payer, etc. Right Speakers B Left : Refer to ABOUT THE ACCESSORY TERMINALS on page 1. 11

12 CONNECTING SPEAKERS Connect the SPEAKERS terminas to your speakers with wire of the proper gauge, cut as short as possibe. If the connections are fauty, no sound wi be heard from the speakers. Make sure that the poarity of the speaker wires is correct, that is, + and markings are observed. If these wires are reversed, the sound wi be unnatura and wi ack bass. Do not et the bare speaker wires touch each other and do not et them touch the meta parts of this unit as this coud damage this unit and/or speakers. Notes One or two speaker systems can be connected to this unit. If you connect ony one speaker system, connect it to either the SPEAKERS A or B terminas. Use speakers with the specified impedance shown on the rear of this unit. <U.S.A., Canada, Austraia and Genera modes ony> Banana Pug connections are aso possibe. Simpy insert the Banana Pug connector into the corresponding termina. How to Connect: Red: positive (+) Back: negative ( ) 1 ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/ ) insuation from the speaker wires.] ➂ Tighten the knob and secure the wire. ABOUT THE ACCESSORY TERMINALS AC OUTLETS (SWITCHED) (U.S.A., Canada, Singapore and Genera modes)... SWITCHED OUTLETS (Austraia mode)... 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outets is controed by this unit s POWER switch or the provided remote contro transmitter s POWER key. These outets wi suppy power to any component whenever this unit is turned on. The maximum power (tota power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100 watts. GND termina (For turntabe use) Connecting the ground wire of the turntabe to the GND termina wi normay minimize hum, but in some cases better resuts may be obtained with the ground wire disconnected. Use one of the two GND terminas on the rear of this unit for the connection. Turntabe FM 75Ω ANT UNBAL or GND GND AM ANT Loosen Tighten 1

13 ANTENNA CONNECTIONS Each antenna shoud be connected to the designated terminas correcty, referring to the foowing diagram. Both AM and FM indoor antennas are incuded with this unit. In genera, these antennas wi probaby provide sufficient signa strength. Nevertheess, a propery instaed outdoor antenna wi give cearer reception than an indoor one. If you experience poor reception quaity, an outdoor antenna may resut in improvement. Engish Outdoor FM antenna Indoor FM antenna (incuded) Outdoor AM antenna GND AM oop antenna (incuded) FM ANT 75Ω UNBAL. 00-ohm feeder GND AM ANT PHONO CD 1 AUX 75-ohm coaxia cabe 75-ohm/00-ohm antenna adapter Ground Connecting the AM oop antenna 1 ➀ ➂ ➁ Orient so that the best reception is obtained. * The AM oop antenna shoud be paced apart from the main unit. The antenna may be hung on a wa. * The AM oop antenna shoud be kept connected, even if an outdoor AM antenna is connected to this unit. GND termina For maximum safety and minimum interference, connect the GND termina to a good earth ground. A good earth ground is a meta stake driven into moist earth. Notes When connecting the indoor FM antenna, insert its connector into the FM ANT termina firmy. If you need an outdoor FM antenna to improve FM reception quaity, either 00-ohm feeder or coaxia cabe may be used. In ocations troubed by eectrica interference, coaxia cabe is preferabe. 1

14 BASIC OPERATIONS 1, 6 7 TO PLAY A SOURCE 1 Seect the speakers to be used. SPEAKERS A B ON ON OFF OFF Set to the position. * If you use two speaker systems, press both the A and B switches. Turn the power on. POWER 5 Pay the source. (For detaied information on the tuning operation, refer to page 17.) 6 Seect the desired input source by using the input seector buttons. RX-95 Adjust to the desired output eve. TUNER CD MONITOR TAPE TAPE 1 AUX PHONO 7 If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS contros, etc. (refer to page 16). COPY RX-95 TUNER TAPE MONITOR AUX PHONO * The name of the seected input source wi appear on the dispay. * Note that pressing on each input seector button seects the source which is connected to the corresponding input terminas on the rear pane. CD Notes RX-95 ony If you seect AUX, TUNER, CD or PHONO, be sure that TAPE 1 and/or TAPE are not being seected. If you seect TAPE 1 and TAPE at the same time, the resut wi be the sound from the tape deck 1. For TAPE 1 and TAPE, whenever the button is pressed, the corresponding input source is seected or canceed aternatey. RX-95 ony Whenever the TAPE MONITOR is pressed, the tape deck is seected or canceed aternatey. If both TAPE MONITOR and another input seector button are seected, TAPE MONITOR takes priority of another input seector button. 1 To turn off the power Press the POWER switch again.

15 TO RECORD A SOURCE TO TAPE 1, Engish RX-95 RX-95 1 Seect the source to be recorded. 1 Seect the source to be recorded. TUNER CD TUNER CD MONITOR TAPE TAPE 1 AUX PHONO TAPE MONITOR AUX PHONO COPY * To dub from tape to tape, refer to the Notes shown beow. * When you seect AUX, TUNER, CD or PHONO, make sure that neither TAPE 1 nor TAPE is aso seected. Pay the source and then turn the VOLUME contro up to confirm the input source. (For detaied information on the tuning operations, refer to the page 17.) Begin recording on the tape deck. To monitor the audio signas being recorded, press the input seector button for the tape deck being used to make the recording. * When you seect AUX, TUNER, CD or PHONO, make sure that TAPE MONITOR is not aso seected. Pay the source and then turn the VOLUME contro up to confirm the input source. (For detaied information on the tuning operations, refer to the page 17.) Begin recording on the tape deck. To monitor the audio signas being recorded, press the TAPE MONITOR. TUNER CD TAPE MONITOR AUX PHONO TUNER CD MONITOR TAPE TAPE 1 AUX PHONO Notes COPY VOLUME, BASS, TREBLE, BALANCE, LOUDNESS contros and PURE DIRECT switch settings have no effect on the materia being recorded. To dub from tape to tape, seect TAPE by pressing it. Ony the foowing method of dubbing can be made by using this unit. Note VOLUME, BASS, TREBLE, BALANCE and LOUDNESS contro settings have no effect on the materia being recorded. SOURCE Tape deck connected to the TAPE terminas. RECORDER Tape deck connected to the TAPE 1 terminas. 15

16 Seecting the SPEAKER system Because one or two speaker systems can be connected to this unit, the SPEAKERS switches aow you to seect speaker system A or B, or both at once. SPEAKERS A B ON ON Using the PURE DIRECT switch RX-95 ony You can enjoy the purest possibe sound from your audio sources by pressing this switch inward. By doing so, the audio signa bypasses the BASS, TREBLE, BALANCE and LOUDNESS contros, eiminating any aterations to the audio signa. PURE DIRECT OFF OFF Adjusting the BALANCE contro Adjust the baance of the output voume to the eft and right speakers to compensate for sound imbaance caused by speaker ocation or istening room conditions. BALANCE 0 L 5 5 R Adjusting the continuousy variabe LOUDNESS contro This contro provides compensation for the human ears oss of sensitivity to high and ow-frequency ranges at ow voume. This contro is adjustabe to retain fu tona range at any voume eve. 1 LOUDNESS Adjusting the BASS and TREBLE contros FLAT 0 db Set to the FLAT position BASS TREBLE 0 0 VOLUME BASS : Turn this cockwise to increase (or countercockwise to decrease) the ow frequency response Set to the oudest istening eve that you woud isten to. TREBLE : Turn this cockwise to increase (or countercockwise to decrease) the high frequency response db 0 LOUDNESS FLAT 0 db 0 Turn unti the desired voume is gained

17 TUNING OPERATIONS Normay, if station signas are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possibe. However, if signas of the station you want to seect are weak, you must tune to it manuay (MANUAL TUNING). 1 Engish AUTOMATIC TUNING MANUAL TUNING 1 Seect the reception band (FM or AM) confirming it on the dispay. 1 Seect the reception band (FM or AM) confirming it on the dispay. FM/AM FM/AM FM or AM FM or AM TUNING MODE AUTO/MAN'L MONO TUNING MODE AUTO/MAN'L MONO Turn AUTO TUNING off. Tune to a desired station manuay. DOWN TUNING UP AUTO TUNING * To continue tuning search, press and hod the button. DOWN TUNING UP Note If you tune to an FM station manuay, it is received in monaura mode automaticay to increase the signa quaity. To tune to a higher frequency, press the right side once. To tune to a ower frequency, press the eft side once. * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signas of the station are weak), change to the MANUAL TUNING method. 17

18 MANUAL PRESET TUNING PRESET TUNING This unit can store station frequencies (seected by tuning operation) by using the PRESET STATIONS buttons. With this function, you can reca any desired station by ony pressing the corresponding PRESET STATIONS button. Up to 0 stations (8 stations x 5 groups) can be stored., 1, To store stations To reca a preset station 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) 1 Seect the group of preset stations. Seect a desired group (A E) of preset stations confirming it on the dispay. A/B/C/D/E PRESET A/B/C/D/E PRESET MEMORY Seect the preset station number. PRESET STATIONS 1 MAN'L/AUTO FM MEMORY Fashes on and off for about 5 seconds. Seect a preset station number where you want to program the station before MEMORY goes off from the dispay. PRESET PRESET STATIONS Notes A new setting can be programmed in pace of the former one. For presets, the setting of the reception mode (stereo or monaura) is stored aong with the station frequency. PRESET FM MHz Shows the dispayed station has been programmed to A1. * In the same way, program other stations to A, A... A8. * You can program more stations to preset station numbers on other groups in the same way by seecting other groups in step. Memory back-up The memory back-up circuit prevents the programmed data from being ost even if the POWER switch is set off or the power pug is disconnected from the AC outet or the power is cut due to temporary power faiure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simpy foowing the PRESET TUNING steps. 18

19 AUTOMATIC PRESET TUNING You can aso make use of an automatic preset tuning function for FM stations ony. By this function, this unit performs automatic tuning and stores FM stations with strong signas sequentiay. Up to 0 stations are stored automaticay in the same way as in the manua preset tuning method on page 18. Engish To store stations 1 FM/AM MEMORY MAN'L/AUTO FM FM Press and hod for about seconds. 1 When the automatic preset tuning is finished The dispay shows the frequency of the ast preset station. Check the contents and the number of preset stations by foowing the procedure of the section To reca a preset station on page 18. To reca a preset station Simpy foow the procedure of the section To reca a preset station on page 18. MEMORY AUTO TUNING Fashes. After 5 seconds, the automatic preset tuning begins from A1. Received stations are programmed to A1, A... A8 sequentiay. * If more than 8 stations are received, they are aso programmed to the preset station numbers on other groups (B, C, D and E) in that order. Notes If no station is received by the automatic preset tuning search, the search finishes after NOTHING fashes for about seconds on the dispay. You can repace a preset station by another FM or AM station manuay by simpy foowing the procedure of the section To store stations on page 18. If the number of received stations is not enough to be stored up to E8, the search wi be finished automaticay when it reaches the highest frequency after searching through a frequencies. With this function, ony FM stations with sufficient signa strength are stored automaticay. If the station you want to program is weak in signa strength, tune to it in monaura manuay and program it by foowing the procedure of the section To store stations on page 18. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for exampe, you want to store the first received station to C5, seect C5 by using the A/B/C/D/E button and the PRESET STATIONS buttons after pressing the MEMORY button in step before the automatic preset tuning begins. The first received station is stored to C5, and next stations to C6, C7... sequentiay. If stations are stored up to E8, the automatic preset tuning is finished automaticay. 19

20 EXCHANGING PRESET STATIONS You can exchange the paces of two preset stations with each other as shown beow., Exampe) If you want to shift the preset station on E1 to A5, and vice versa. 1 Reca the preset station on E1 (by foowing the method of To reca a preset station on page 18). EDIT EDIT MEMORY Shows the exchange of stations is competed. Fashes Next, reca the preset station on A5 by foowing the same method with step 1. MEMORY Fashes 0

21 NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery instaation Remote contro transmitter operation range Engish 1 Remote contro sensor Within approximatey 6 m (19.7 feet) 0 0 Battery repacement If you find that the remote contro transmitter must be used coser to the main unit, the batteries are weak. Repace both batteries with new ones. Notes Use ony AA, R6, UM- batteries for repacement. Be sure the poarities are correct. (See the iustration inside the battery compartment.) Remove the batteries if the remote contro transmitter wi not be used for an extended period of time. If batteries eak, dispose of them immediatey. Avoid touching the eaked materia or etting it come in contact with cothing, etc. Cean the battery compartment thoroughy before instaing new batteries. Notes There shoud be no arge obstaces between the remote contro transmitter and the main unit. If the remote contro sensor is directy iuminated by strong ighting (especiay an inverter type of fuorescent amp etc.), it might cause the remote contro transmitter not to work correcty. In this case, reposition the main unit to avoid direct ighting. 1

22 TROUBLESHOOTING If the unit fais to operate normay, check the foowing points to determine whether the faut can be corrected by the simpe measures suggested. If it cannot be corrected, or if the faut is not isted in the SYMPTOM coumn, disconnect the power cord and contact your authorized YAMAHA deaer or service center for hep. Ampifier FM AM Remote contro Others transmitter The unit fais to turn on when the POWER switch is pressed. No sound. The sound suddeny goes off. Ony one side speaker outputs the sound. There is a ack of bass, and no ambience. Sound hums. Sound eve is ow. SYMPTOM CAUSE REMEDY The voume eve is ow whie paying a record. The voume eve cannot be increased, or sound is distorted. FM stereo reception is noisy. There is distortion and cear reception cannot be obtained even with a good FM antenna. A desired station cannot be tuned in with the automatic tuning method. Previousy preset stations can no onger be tuned in. A desired station cannot be tuned in with the automatic tuning method. There are continuous cracking and hissing noises. There are buzzing and whining noises (especiay in the evening). The remote contro transmitter does not work. The sound is degraded when istening with the headphones connected to the compact disc payer or cassette deck that are connected with this unit. Power cord is not pugged in or is not competey inserted. Incorrect output cord connections. Appropriate input seector button is not pressed. The SPEAKERS switches are not set propery. Speaker connections are not secure. The protection circuit has been activated because of short circuit etc. The SLEEP timer functioned. Incorrect setting of the BALANCE contro. Incorrect cord connections. The + and wires are connected in reverse at this unit or speakers. Incorrect cord connections. No connection from the turntabe to the GND termina. The LOUDNESS contro is functioning. The record is being payed on a turntabe with an MC cartridge. The power to the component connected to the REC OUT terminas of this unit is off. Because of the characteristics of FM stereo broadcasts, this is imited to cases where the transmitter is too far away or the antenna input is poor. There is mutipath interference. The station is too weak. The tuner has been unpugged for a ong period. Weak signa or oose antenna connections. Noises wi resut from igtning, fuorescent amps, motors, thermostats and other eectrica equipment. A teevision set is being used nearby. Direct sunight or ighting (of an inverter type of fourescent amp etc.) is striking the remote contro sensor of the main unit. The batteries of this remote contro transmitter are too weak. The power to this unit is off. Firmy pug in the power cord. Connect the cords propery. If the probem persists, the cords may be defective. Press the appropriate input seector button corresponding to the input source. Set the SPEAKERS switch that corresponds to the speakers to be used to the ON position. Secure the connections. Turning the unit off and then on wi reset the protection circuit. Cance the SLEEP timer function. Adjust it to the appropriate position. Connect the cords propery. If the probem persists, the cords may be defective. Connect the speaker wires in the correct phase (+ and ). Firmy connect the audio pugs. If the probem persists, the cords may be defective. Make the GND connection between the turntabe and this unit. Set the LOUDNESS contro to the FLAT position. The payer shoud be connected to the unit through an MC head ampifier (avaiabe separatey). Turn the power to the component on. Check the antenna connections. Try using a high quaity directiona FM antenna. Set the TUNING MODE button to the manua tuning mode. Adjust antenna pacement to eiminate mutipath interference. Use the manua tuning method. Use a high quaity directiona FM antenna. Repeat the presetting procedure. Tighten the AM oop antenna connections and rotate it for best reception. Use the manua tuning method. Use an outdoor antenna and a ground wire. This wi hep somewhat but it is difficut to eiminate a noise. Reocate this unit away from the TV. Change the position of the main unit. Repace the batteries with new ones. Turn the power to this unit on.

23 SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power per Channe 8 ohms, 0 Hz to 0 khz, 0.0% THD <RX-95>...70W+70W <RX-95>...5W+5W 6 ohms, 0 Hz to 0 khz, 0.06% THD <RX-95>...80W+80W <RX-95>...8W+8W Headphone Jack Rated Output/Impedance Output Leve (8 ohms, 0.0% THD) <RX-95>...0.8V <RX-95>...0.5V Impedance <RX-95>...90 ohms <RX-95>...0 ohms Engish Dynamic Power per Channe (by IHF Dynamic Headroom measuring method) <RX-95> 8/6// ohms...100/10/15/170w <RX-95> 8/6// ohms...68/75/85/95w DIN Standard Output Power per Channe ohms, 1 khz, 0.7% THD [Singapore mode ony] <RX-95>...100W <RX-95>...55W IEC Power 8 ohms, 1 khz, 0.0% THD [Singapore mode ony] <RX-95>...80W <RX-95>...50W Power Band Width <RX-95> 8 ohms, 5W, 0.08% THD...10 Hz to 50 khz <RX-95> 8 ohms,.5w, 0.08% THD...10 Hz to 50 khz Damping Factor 8 ohms, 0 Hz to 0 khz or more Maximum Output Power (EIAJ) [Genera mode ony] <RX-95> 8 ohms, 1 khz, 10% THD...100W <RX-95> 8 ohms, 1 khz, 10% THD...70W Input Sensitivity/Impedance PHONO MM...5 mv/7 k-ohms CD/TAPE/AUX mv/7 k-ohms Maximum Input Signa (1 khz, 0.0% THD) PHONO MM...90 mv Output Leve REC OUT mv Frequency Response (0 Hz to 0 khz) CD/TAPE/AUX...0±0.5 db RIAA Equaization Deviation PHONO MM...0±0.5 db Tota Harmonic Distortion PHONO MM to REC OUT 0 Hz to 0 khz, 1V...0.0% CD/TAPE/AUX to SP OUT 0 Hz to 0 khz, 5W/8 ohms...0.0% Signa-to-Noise Ratio (IHF-A Network) PHONO MM to REC OUT (5 mv Input Shorted)...8 db CD/TAPE/AUX to SP OUT (Input Shorted) db Residua Noise (IHF-A Network) µv Channe Separation (Vo. 0 db, EFFECT OFF) CD/TAPE/AUX (Input 5.1 k-ohms Terminated, 1 khz)...60 db Tone Contro Characteristics BASS: Boost/cut...±10 db (50 Hz) Turnover Frequency...(50 Hz) TREBLE: Boost/cut...±10 db (0 khz) Turnover Frequency...(.5 khz) Continuous Loudness Contro... 0 db (1 khz) (Leve reated equaization) FM SECTION Tuning Range [Austraia, Singapore and Genera modes] to MHz [U.S.A. and Canada modes] to MHz 50 db Quieting Sensitivity (IHF, 75 ohms) [Except Singapore mode] Mono µv (15.1 dbf) Stereo...1 µv (7.7 dbf)

24 Usabe Sensitivity (75 ohms) (0 db S/N Quieting, 1 khz, 100% mod.) [Except Singapore mode] µv (9. dbf) DIN, Mono (S/N 6 db) [Singapore mode ony] µv DIN, Stereo (S/N 6 db) [Singapore mode ony]... µv Image Response Ratio [Singapore mode ony]...80 db [Except Singapore mode]...5 db IF Response Ratio...80 db Spurious Response Ratio...70 db AM Suppression Ratio...55 db Capture Ratio db Aternate Channe Seectivity [Except Singapore mode]...85 db Seectivity (two signas, ±00 khz, 0 khz Dev.) [Singapore mode ony]...70 db Signa-to-Noise Ratio (IHF) Mono/Stereo [Except Singapore mode]...80 db/75 db (DIN-Weighted, 0 khz Dev.) Mono/Stereo [Singapore mode ony]...75 db/70 db Harmonic Distortion Mono/Stereo (1kHz, 0 khz Dev.)...0.1%/0.% Stereo Separation (1 khz, 0 khz Dev.)...50 db Frequency Response 0 Hz to 15 khz...0 ±1.5 db AM SECTION Tuning Range [Austraia and Singapore modes]...51 to 1,611 khz [U.S.A., Canada and Genera modes]...50 to 1,710 khz Usabe Sensitivity µv/m Seectivity... db Signa-to-Noise Ratio...50 db Image Response Ratio...0 db Spurious Response Ratio...50 db Harmonic Distortion (1 khz)...0.% AUDIO SECTION Output Leve/Impedance FM (100% mod., 1 khz) mv/. k-ohms AM (0% mod., 1 khz) mv/. k-ohms GENERAL Power Suppy [U.S.A. and Canada modes]...ac 10V, 60 Hz [Austraia mode]...ac 0V, 50 Hz [Singapore mode]...ac 0V, 50 Hz [Genera mode]...ac /0-0V, 60/50 Hz Power Consumption <RX-95> [U.S.A. mode]...160w [Canada mode]...60va, 10W [Austraia, Singapore and Genera modes]...15w <RX-95> [U.S.A., Singapore, Austraia and Genera modes]...10w [Canada mode]...170w AC Outets SWITCHED OUTLETS [U.S.A., Canada, Singapore and Genera modes]...100w max. tota 1 SWITCHED OUTLET [Austraia mode]...100w max. tota Dimensions (W x H x D)...5 x 16 x 08.5 mm (17-1/8 x 5-/ x 1-1/8 ) Weight <RX-95> kg (17 bs. oz.) <RX-95> kg (1 bs. 5 oz.) Accessories...AM oop antenna Indoor FM antenna Remote contro transmitter Batteries <U.S.A. and Canada mode ony> Antenna adapter Specifications are subject to change without notice.

25 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 9060, U.S.A. YAMAHA CANADA MUSIC LTD. 15 MILNER AVE., SCARBOROUGH, ONTARIO M1S R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. -, D-56 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 771 MARNE-LA-VALLEE CEDEX0, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 00 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 005, 00 VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17- MARKET ST., SOUTH MELBOURNE, 05 VIC., AUSTRALIA VU670