RX-V492 RX-V392. Natural Sound AV Receiver Récepteur audiovisuel Son Naturel Receptor AV de Sonido Natural

Transcription

1 RX-V9 RX-V9 Natura Sound AV Receiver Récepteur audiovisue Son Nature Receptor AV de Sonido Natura Thank you for seecting this YAMAHA AV receiver. Nous vous remercions d avoir porté votre choix sur ce récepteur audiovisue YAMAHA. Muchas gracias por haber adquirido este receptor AV YAMAHA. OWNER S MANUAL MODE D EMPLOI MANUAL DE INSTRUCCIONES

2 SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Expanation of Graphica Symbos The ightning fash with arrowhead symbo, within an equiatera triange, is intended to aert you to the presence of uninsuated dangerous votage within the product s encosure that may be of sufficient magnitude to constitute a risk of eectric shock to persons. The excamation point within an equiatera triange is intended to aert you to the presence of important operating and maintenance (servicing) instructions in the iterature accompanying the appiance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1 Read Instructions A the safety and operating instructions shoud be read before the unit is operated. Retain Instructions The safety and operating instructions shoud be retained for future reference. Heed Warnings A warnings on the unit and in the operating instructions shoud be adhered to. Foow Instructions A operating and other instructions shoud be foowed. 5 Water and Moisture The unit shoud not be used near water for exampe, near a bathtub, washbow, kitchen sink, aundry tub, in a wet basement, or near a swimming poo, etc. 6 Carts and Stands The unit shoud be used ony with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination shoud be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 Wa or Ceiing Mounting The unit shoud be mounted to a wa or ceiing ony as recommended by the manufacturer. Ventiation The unit shoud be situated so that its ocation or position does not interfere with its proper ventiation. For exampe, the unit shoud not be situated on a bed, sofa, rug, or simiar surface, that may bock the ventiation openings; or paced in a buit-in instaation, such as a bookcase or cabinet that may impede the fow of air through the ventiation openings. 9 Heat The unit shoud be situated away from heat sources such as radiators, stoves, or other appiances that produce heat. 1 Power Sources The unit shoud be connected to a power suppy ony of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection Power-suppy cords shoud be routed so that they are not ikey to be waked on or pinched by items paced upon or against them, paying particuar attention to cords at pugs, convenience receptaces, and the point where they exit from the unit. 1 Ceaning The unit shoud be ceaned ony as recommended by the manufacturer. 1 Nonuse Periods The power cord of the unit shoud be unpugged from the outet when eft unused for a ong period of time. 1 Object and Liquid Entry Care shoud be taken so that objects do not fa into and iquids are not spied into the inside of the unit. 15 Damage Requiring Service The unit shoud be serviced by quaified service personne when: A. The power-suppy cord or the pug has been damaged; or B. Objects have faen, or iquid has been spied into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normay or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing The user shoud not attempt to service the unit beyond those means described in the operating instructions. A other servicing shoud be referred to quaified service personne. 17 Power Lines An outdoor antenna shoud be ocated away from power ines. 1 Grounding or Poarization Precautions shoud be taken so that the grounding or poarization is not defeated.

3 19 For US customers ony: Outdoor Antenna Grounding If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against votage surges and buit-up static charges. Artice 1 of the Nationa Eectrica Code, ANSI/NFPA 7, provides information with regard to proper grounding of the mast and supporting structure, grounding of the ead-in wire to an antenna discharge unit, size of grounding conductors, ocation of antenna discharge unit, connection to grounding eectrodes, and requirements for the grounding eectrode. EXAMPLE OF ANTENNA GROUNDING MAST GROUND CLAMP ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 1 ) Engish Note to CATV system instaer: This reminder is provided to ca the CATV system instaer s attention to Artice - of the NEC that provides guideines for proper grounding and, in particuar, specifies that the cabe ground sha be connected to the grounding system of the buiding, as cose to the point of cabe entry as practica. ELECTRIC SERVICE EQUIPMENT NEC NATIONAL ELECTRICAL CODE GROUNDING CONDUCTORS (NEC SECTION 1 1) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 5. PART H) SPECIAL NOTES FOR FCC COMPOSITE DEVICE (for US customers ony) This device is a composite system. The digita device component may not cause harmfu interference. FCC INFORMATION (for US customers ony) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when instaed as indicated in the instructions contained in this manua, meets FCC requirements. Modifications not expressy approved by Yamaha may void your authority, granted by the FCC, to use the product.. IMPORTANT : When connecting this product to accessories and/or another product use ony high quaity shieded cabes. Cabe/s suppied with this product MUST be used. Foow a instaation instructions. Faiure to foow instructions coud void your FCC authorization to use this product in the USA.. NOTE : This product has been tested and found to compy with the requirements isted in FCC Reguations, Part 15 for Cass B digita devices. Compiance with these requirements provides a reasonabe eve of assurance that your use of this product in a residentia environment wi not resut in harmfu interference with other eectronic devices. This equipment generates/uses radio frequencies and, if not instaed and used according to the instructions found in the users manua, may cause interference harmfu to the operation of other eectronic devices. Compiance with FCC reguations does not guarantee that interference wi not occur in a instaations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, pease try to eiminate the probem by using one of the foowing measures: Reocate either this product or the device that is being affected by the interference. Utiize power outets that are on different branch (circuit breaker or fuse) circuits or insta AC ine fiter/s. In the case of radio or TV interference, reocate/reorient the antenna. If the antenna ead-in is ohm ribbon ead, change the ead-in to coaxia type cabe. If these corrective measures do not produce satisfactory resuts, pease contact the oca retaier authorized to distribute this type of product. If you can not ocate the appropriate retaier, pease contact Yamaha Eectronics Corp., U.S.A. 666 Orangethorpe Ave, Buena Park, CA 96. The above statements appy ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime (for US customers ony) YAMAHA and the Eectronic Industries Association s Consumer Eectronics Group want you to get the most out of your equipment by paying it at a safe eve. One that ets the sound come through oud and cear without annoying baring or distortion and, most importanty, without affecting your sensitive hearing. Since hearing damage from oud sounds is often undetectabe unti it is too ate, YAMAHA and the Eectronic Industries Association s Consumer Eectronics Group recommend you to avoid proonged exposure from excessive voume eves. 1

4 CONTENTS Safety Instructions...Inside the Front Cover Suppied Accessories... Features... Caution... Notes about the Remote Contro Transmitter...5 Profie of This Unit...6 Speaker Setup...7 Connections... Contros and Their Functions...1 Speaker Baance Adjustment... Basic Operations... Tuning Operations...6 Preset Tuning...7 Using Digita Sound Fied Processor (DSP)... Setting the SLEEP Timer... Troubeshooting...5 Specifications...6 SUPPLIED ACCESSORIES After unpacking, check that the foowing parts are incuded. Indoor FM Antenna Remote Contro Transmitter RX-V9 RX-V9 AM Loop Antenna TIME/ DELAY/CENTER LEVEL + /REAR TEST EFFECT DELAY TIME+ TEST EFFECT PROGRAM PROLOGIC ENHANCED ON/OFF PROGRAM PROLOGIC ENHANCED ON/OFF VCR TV/DBS DVD/LD VCR VIDEO DIR A DIR B REC/PAUSE PLAY DIR A DIR B REC/PAUSE PLAY A/B TAPE A/B TAPE PRESET + A/B/C/D/E TUNER PRESET + A/B/C/D/E TUNER DISC PLAY CD DISC PLAY CD PHONO PHONO SLEEP POWER VOLUME SLEEP POWER VOLUME Antenna adapter (U.S.A. and Canada modes ony) Batteries (size AA, R6, UM-)

5 FEATURES Engish 5 Speaker Configuration RX-V9 <U.S.A. and Canada modes> Main: 7W + 7W (Ω) RMS Output Power,.% THD,, Hz Center: 7W (Ω) RMS Output Power,.9% THD, 1 khz Rear: W + W (Ω) RMS Output Power,.7% THD, 1 khz <Austraia and Genera modes> Main: 65W + 65W (Ω) RMS Output Power,.% THD,, Hz Center: 65W (Ω) RMS Output Power,.9% THD, 1 khz Rear: W + W (Ω) RMS Output Power,.7% THD, 1 khz RX-V9 <U.S.A. and Canada modes> Main: 5W + 5W (Ω) RMS Output Power,.% THD,, Hz Center: 5W (Ω) RMS Output Power,.9% THD, 1 khz Rear: W + W (Ω) RMS Output Power,.7% THD, 1 khz <Austraia and Genera modes> Main: 5W + 5W (Ω) RMS Output Power,.% THD,, Hz Center: 5W (Ω) RMS Output Power,.9% THD, 1 khz Rear: W + W (Ω) RMS Output Power,.7% THD, 1 khz Digita Sound Fied Processor Doby Pro Logic Surround Decoder Theater-ike Sound Experience by the Combination of Doby Pro Logic and YAMAHA DSP Technoogy (CINEMA DSP) Automatic Input Baance Contro for Doby Pro Logic Surround Test Tone Generator for Easier Speaker Baance Adjustment Center Channe Modes (NORMAL/WIDE/PHANTOM) -Station Random Access Preset Tuning Automatic Preset Tuning Preset Station Shifting Capabiity (Preset Editing) IF Count Direct PLL Synthesizer Tuning System Video Signa Input/Output Capabiity SLEEP Timer Remote Contro Capabiity

6 CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, pease read this manua carefuy. Keep it in a safe pace for future reference.. Insta this unit in a coo, dry, cean pace away from windows, heat sources, sources of excessive vibration, dust, moisture and cod. Avoid sources of humming (transformers, motors). To prevent fire or eectrica shock, do not expose the unit to rain or water.. Never open the cabinet. If something drops into the set, contact your deaer.. Do not use force on switches, contros or connection wires. When moving the unit, first disconnect the power pug and the wires connected to other equipment. Never pu the wires themseves. 5. The openings on the cabinet assure proper ventiation of the unit. If these openings are obstructed, the temperature inside the cabinet wi rise rapidy. Therefore, avoid pacing objects against these openings, and insta the unit in weventiated condition. Make sure to aow a space of at east 1 cm behind, cm on the both sides and cm above the top pane of the unit. Otherwise it may not ony damage the unit, but aso cause fire. 6. Aways set the VOLUME contro to before starting the audio source pay. Increase the voume graduay to an appropriate eve after payback has been started. 7. Do not attempt to cean the unit with chemica sovents; this might damage the finish. Use a cean, dry coth.. Be sure to read the TROUBLESHOOTING section regarding common operating errors before concuding that the unit is fauty. 9. When not panning to use this unit for ong periods of time (ie., vacation, etc.), disconnect the AC power pug from the wa outet. IMPORTANT Pease record the seria number of this unit in the space beow. Seria No.: The seria number is ocated on the rear of the unit. Retain this Owner s Manua in a safe pace for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. FOR CANADIAN CUSTOMERS TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS. The apparatus is not disconnected from the AC power source as ong as it is connected to the wa outet, even if the apparatus itsef is turned off. FREQUENCY STEP switch (Genera Mode ony) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (ocated at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power pug of this unit from the AC outet. 1. To prevent ightning damage, disconnect the AC power pug and disconnect the antenna cabe when there is an eectrica storm. 11. Grounding or poarization Precautions shoud be taken so that the grounding or poarization of an appiance is not defeated. 1. AC outet Do not connect audio equipment to the AC outet on the rear pane if that equipment requires more power than the outet is rated to provide. 1. Votage Seector (Genera Mode ony) The votage seector on the rear pane of this unit must be set for your oca main votage BEFORE pugging into the AC main suppy. Votages are 11/1// V AC, 5/6 Hz.

7 NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery instaation Remote contro transmitter operation range Engish RX-V9 RX-V9 1 Remote contro sensor Within approximatey 6 m (19.7 feet) Battery repacement If you find that the remote contro transmitter must be used coser to the main unit, the batteries are weak. Repace both batteries with new ones. Notes Use ony AA, R6, UM- batteries for repacement. Be sure the poarities are correct. (See the iustration inside the battery compartment.) Remove the batteries if the remote contro transmitter wi not be used for an extended period of time. If batteries eak, dispose of them immediatey. Avoid touching the eaked materia or etting it come in contact with cothing, etc. Cean the battery compartment thoroughy before instaing new batteries. Notes There shoud be no arge obstaces between the remote contro transmitter and the main unit. If the remote contro sensor is directy iuminated by strong ighting (especiay an inverter type of fuorescent amp etc.), it might cause the remote contro transmitter not to work correcty. In this case, reposition the main unit to avoid direct ighting. 5

8 PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver an extremey sophisticated audio component. The Digita Sound Fied Processor (DSP) buit into this unit takes advantage of Yamaha s undisputed eadership in the fied of digita audio processing to bring you a whoe new word of istening experiences. Foow the instructions in this manua carefuy when setting up your system, and this unit wi sonicay transform your room into a wide range of istening environments movie theater, concert ha, and so on. In addition, you get incredibe reaism from sources encoded with Doby Surround using the buit-in Doby Pro Logic Surround Decoder. Pease read this operation manua carefuy and store it in a safe pace for ater reference. Digita Sound Fied Processing What is it that makes ive music so good? Today s advanced sound reproduction technoogy ets you get extremey cose to the sound of a ive performance, but chances are you sti notice something missing: the acoustic environment of the ive concert ha. Extensive research into the exact nature of the sonic refections that create the ambience of a arge ha has made it possibe for Yamaha engineers to bring you this same sound in your own istening room, so you fee a the sound of a ive concert. Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possibe to capture the acoustics of a variety of venues such as an actua concert ha, theater, etc. to aow you to accuratey recreate one of severa actua ive performance environments, a in your own home. Doby Pro Logic Surround This unit empoys a Doby Pro Logic Surround decoder simiar to professiona Doby Stereo decoders used in many movie theaters. By using the Doby Pro Logic Surround decoder, you can experience the dramatic reaism and impact of Doby Surround movie theater sound in your own home. Doby Pro Logic empoys a four channe five speaker system. The Pro Logic Surround system divides the input signa into four eves: the eft and right main channes, the center channe (used for diaog), and the rear surround sound channes (used for sound effects, background noise, and other ambient noises). The center channe aows isteners seated in even ess-than-idea positions to hear the diaog originating from the action on the screen whie experiencing good stereo imaging. Doby Surround is encoded on the sound track of pre-recorded video tapes, aser discs, and some TV/cabe broadcasts. When you pay a source encoded with Doby Surround on this unit, the Doby Pro Logic Surround decoder decodes the signa and distributes the surround-sound effects. This Doby Pro Logic Surround Decoder empoys a digita signa processing system. This system improves the stabiity of sound at each channe and minimizes crosstak between channes, so that positioning of sounds around the room is more accurate compared with conventiona anaog signa processing systems. In addition, this unit features a buit-in automatic input baance contro. This aways assures you the best performance without manua adjustment. Manufactured under icense from Doby Laboratories Licensing Corporation. Doby, the doube-d symbo and Pro Logic are trademarks of Doby Laboratories Licensing Corporation. Doby Pro Logic Surround + DSP Doby Surround sound system shows its fu abiity in a arge movie theater, because movie sounds are originay designed to be reproduced in a arge movie theater using many speakers. It is difficut to create a sound environment simiar to that of a movie theater in your istening room, because the room size, materias of inside was, the number of speakers, etc. of your istening room is much different from those of a movie theater. Yamaha DSP technoogy made it possibe to present you with neary the same sound experience as that of a arge movie theater in your istening room by compensating for ack of presence and dynamics in your istening room with its origina digita sound fieds combined with Doby Surround sound fied. The combination of Doby Pro Logic Surround and DSP is used on the sound fied program PRO LOGIC ENHANCED. CINEMA DSP The YAMAHA CINEMA DSP ogo indicates these programs are created by the combination of Doby Pro Logic and YAMAHA DSP technoogy. 6

9 SPEAKERS TO BE USED SPEAKER SETUP Engish This unit is designed to provide the best sound-fied quaity with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the -Speaker Configuration shown beow.) The main speakers are used for the main source sound pus the effect sounds. They wi probaby be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (diaog etc.) within programs encoded with Doby Surround. The center speaker needs to be equa in power to the main speakers, athough the rear speakers shoud not be equa. However, a the speakers shoud have high enough power handing to accept the maximum output of this unit. SPEAKER CONFIGURATION 5-Speaker Configuration This configuration is the most effective and recommended one. In this configuration, the center speaker is necessary as we as the rear speakers. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is seected, conversations wi be output from the center speaker and the ambience wi be exceent. Set the center channe mode to the NORMAL or WIDE position. (For detais, refer to page 1.) -Speaker Configuration The center speaker is not used in this configuration. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is seected, the center sound is output from the eft and the right main speakers. However, the sound effect of other programs can be the same as that of the 5-speaker configuration. Be sure to set the center channe mode to the PHANTOM position. (For detais, refer to page 1.) Front Main L Center Main Front R Front Main L Main Front R Diaogue Diaogue Surround sound Surround sound Rear L Rear R Rear L Rear R SPEAKER PLACEMENT The recommended speaker configuration, the 5-speaker configuration, wi require two speaker pairs: main speakers (your norma stereo speakers), and rear speakers, pus a center speaker. When you pace these speakers, refer to the foowing. Front Main R Center Main Front L TV set Main: In norma position. (The position of your present stereo speaker system.) Rear: Behind your istening position, facing sighty inward. Neary six feet (approx. 1. m) up from the foor. Center: Precisey between the main speakers. (To avoid interference with TV sets, use a magneticay shieded speaker.) Rear R Rear L 7

10 CONNECTIONS Never pug in this unit and other components unti a connections are competed. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure a connections are made correcty, that is to say L (eft) to L, R (right) to R, + to + and to. Aso, refer to the owner s manua for each component to be connected to this unit. * If you have YAMAHA components numbered as 1,,, etc. on the rear pane, connections can be made easiy by making sure to connect the output (or input) terminas of each component to the same-numbered terminas of this unit. RX-V9 Turntabe Monitor TV Video cassette recorder TV/Sateite tuner OUTPUT GND VIDEO IN VIDEO OUT AUDIO OUT VIDEO IN AUDIO IN VIDEO OUT AUDIO OUT * (U.S.A. mode) 75Ω UNBAL. GND VIDEO SIGNAL MONITOR OUT DVD/LD IN VCR OUT TV/DBS REAR IMPEDANCE SELECTOR REAR 6ΩMIN./SPEAKER OUTPUT CENTER SINGLE:6ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER MAIN A OR B:ΩMIN./SPEAKER A B:ΩMIN./SPEAKER CENTER REAR ΩMIN./SPEAKER FM ANT GND AM ANT CENTER C SINGLE DUAL CENTER MAIN D SINGLE:ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER A OR B:ΩMIN./SPEAKER A B:I6ΩMIN./SPEAKER SUB WOOFER A * 1 MAINS PHONO TAPE PB TAPE ( MD ) REC OUT DVD/LD AUDIO SIGNAL IN VCR OUT TV/DBS B MAIN 1 CD CAUTION SEE INSTRUCTION IV 6Hz MANUAL FOR CORRECT SETTING. IW MAX. TOTAL SWITCHED AC SPEAKERS OUTLETS To AC outet LINE OUT LINE IN VIDEO OUT AUDIO OUT OUTPUT Tape deck, MD recorder, etc. LD payer etc. CD payer * 1,* : See the next page.

11 RX-V9 Engish Turntabe Monitor TV Video cassette recorder OUTPUT GND 75Ω UNBAL. GND VIDEO SIGNAL MONITOR OUT VIDEO IN VCR OUT REAR IMPEDANCE SELECTOR REAR 6ΩMIN./SPEAKER OUTPUT CENTER SINGLE:6ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER MAIN A OR B:ΩMIN./SPEAKER A B:ΩMIN./SPEAKER CENTER REAR ΩMIN./SPEAKER FM ANT GND AM ANT CENTER C SINGLE DUAL CENTER MAIN D SINGLE:ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER A OR B:ΩMIN./SPEAKER A B:I6ΩMIN./SPEAKER SUB WOOFER A MAINS PHONO TAPE PB TAPE ( MD ) REC OUT VIDEO AUDIO SIGNAL IN VCR OUT B MAIN 1 CD CAUTION SEE INSTRUCTION IV MANUAL 6Hz FOR CORRECT SETTING. IW MAX. TOTAL SWITCHED AC SPEAKERS OUTLETS LINE OUT LINE IN VIDEO OUT AUDIO OUT OUTPUT VIDEO IN VIDEO OUT AUDIO OUT VIDEO IN AUDIO IN * (U.S.A. mode) * 1 To AC outet Tape deck, MD recorder, etc. LD payer etc. CD payer AC * 1 OUTLET(S) (SWITCHED) * (U.S.A., Canada and Genera modes)... SWITCHED OUTLETS (Austraia mode)... 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outets is controed by this unit s POWER switch or the provided remote contro transmitter s POWER key. These outets wi suppy power to any component whenever this unit is turned on. The maximum power (tota power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 1 watts. GND termina (For turntabe use) Connecting the ground wire of the turntabe to the GND termina wi normay minimize hum, but in some cases better resuts may be obtained with the ground wire disconnected. 9

12 CONNECTING SPEAKERS Rear speaker Rear speaker Subwoofer system Right Left Center speaker (U.S.A. mode) REAR CENTER OUTPUT CENTER IMPEDANCE SELECTOR REAR 6ΩMIN./SPEAKER CENTER SINGLE:6ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER MAIN A OR B:ΩMIN./SPEAKER A B:ΩMIN./SPEAKER REAR ΩMIN./SPEAKER CENTER SINGLE:ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER MAIN A OR B:ΩMIN./SPEAKER A B:I6ΩMIN./SPEAKER C DUAL D SUB WOOFER SINGLE A Left Main speakers B Right Right Left MAIN CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. B SPEAKERS Main speakers A Note Use speakers with the specified impedance shown on the rear of this unit. Note on main speaker connections: One or two speaker systems can be connected to this unit. If you use ony one speaker system, connect it to either the SPEAKERS A or B terminas. Note on center speaker connection: One or two center speakers can be connected to this unit. If you cannot pace the center speaker on or under the TV, it is recommended to use two center speakers and pace them on both sides of the TV to orient the center sound at the center position. For connecting two center speakers, foow the method shown beow. Note on a subwoofer connection: You may wish to add a subwoofer to reinforce ow frequencies. Connect the SUBWOOFER OUTPUT termina of this unit to the INPUT termina of the subwoofer ampifier, and connect the speaker terminas of the subwoofer ampifier to the subwoofer. With some subwoofers, incuding the Yamaha Active Servo Processing Subwoofer System, the ampifier and subwoofer are in the same unit. REAR CENTER C D DUAL SINGLE Center speaker Center speaker 1

13 How to Connect: Connect the SPEAKERS terminas to your speakers with wire of the proper gauge, cut as short as possibe. If the connections are fauty, no sound wi be heard from the speakers. Make sure that the poarity of the speaker wires is correct, that is the + and markings are observed. If these wires are reversed, the sound wi be unnatura and ack bass. Caution Do not et the bare speaker wires touch each other and do not et them touch any meta part of this unit. This coud damage this unit and/or speakers. Engish For connecting to the MAIN SPEAKERS terminas Red: positive (+) Back: negative ( ) For connecting to the REAR and CENTER SPEAKERS terminas Red: positive (+) Back: negative ( ) 1 ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/ ) insuation from the speaker wires.] ➂ Tighten the knob and secure the wire. ➀ ➂ ➀ Press the tab. ➁ Insert the bare wire. [Remove approx. 5mm (1/ ) insuation from the speaker wires.] ➂ Reease the tab and secure the wire. ➁ Banana Pug connections are aso possibe. Simpy insert the Banana Pug connector into the corresponding termina. 11

14 OUTPUT terminas (for driving speakers with externa ampifiers) OUTPUT CENTER SUB WOOFER CENTER OUTPUT termina This termina is for center channe ine output. There is no connection to this termina when you use the buit-in ampifier. However, if you drive a center speaker with an externa power ampifier, connect the input termina of the externa ampifier to this termina. SUBWOOFER OUTPUT termina This termina is for connecting with the input termina of an ampifier for driving a subwoofer. This termina outputs ony frequencies beow Hz from the main and center channes. Note Output eve of signas from these terminas are adjusted by the use of VOLUME contro on the front pane or VOLUME keys on the remote contro transmitter. IMPEDANCE SELECTOR switch Be sure to switch this ony when the power of this unit is turned off. Seect the position whose requirements your speaker system meets. IMPEDANCE SELECTOR REAR CENTER MAIN REAR CENTER MAIN 6ΩMIN./SPEAKER SINGLE:6ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER A OR B:ΩMIN./SPEAKER A B:ΩMIN./SPEAKER ΩMIN./SPEAKER SINGLE:ΩMIN./SPEAKER DUAL:ΩMIN./SPEAKER A OR B:ΩMIN./SPEAKER A B:I6ΩMIN./SPEAKER (U.S.A. mode) Rear: (Upper position) The impedance of each speaker must be 6Ω or higher. Center: If you use one center speaker, the impedance of the speaker must be 6Ω or higher. If you use two center speakers, the impedance of each speaker must be Ω or higher. Main: If you use one pair of main speakers, the impedance of each speaker must be Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be Ω or higher. (Lower position) Rear: The impedance of each speaker must be Ω or higher. Center: If you use one center speaker, the impedance of the speaker must be Ω or higher. If you use two center speakers, the impedance of each speaker must be Ω or higher. Main: If you use one pair of main speakers, the impedance of each speaker must be Ω or higher. <Except Canada mode> If you use two pairs of main speakers, the impedance of each speaker must be 16Ω or higher. 1

15 ANTENNA CONNECTIONS Each antenna shoud be connected to the designated terminas correcty, referring to the foowing diagram. Both AM and FM indoor antennas are incuded with this unit. In genera, these antennas wi probaby provide sufficient signa strength. Nevertheess, a propery instaed outdoor antenna wi give cearer reception than an indoor one. If you experience poor reception quaity, an outdoor antenna may resut in improvement. Engish Outdoor FM antenna Indoor FM antenna (incuded) Outdoor AM antenna 75-ohm/-ohm antenna adapter FM ANT 75Ω UNBAL. GND AM oop antenna (incuded) 75-ohm coaxia cabe GND AM ANT 75-ohm/-ohm antenna adapter -ohm feeder Ground Connecting the AM oop antenna 1 ➀ ➂ ➁ Orient so that the best reception is obtained. * The AM oop antenna shoud be paced apart from the main unit. The antenna may be hung on a wa. * The AM oop antenna shoud be kept connected, even if an outdoor AM antenna is connected to this unit. GND termina For maximum safety and minimum interference, connect the GND termina to a good earth ground. A good earth ground is a meta stake driven into moist earth. Notes When connecting the indoor FM antenna, insert its connector into the FM ANT termina firmy. If you need an outdoor FM antenna to improve FM reception quaity, either -ohm feeder or coaxia cabe may be used. In ocations troubed by eectrica interference, coaxia cabe is preferabe. 1

16 FRONT PANEL CONTROLS AND THEIR FUNCTIONS RX-V NATURAL SOUND AV RECEIVER RX V9 CINEMA DSP PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE STADIUM DISCO ROCK CONCERT CONCERT HALL EFFECT VOLUME 6 VCR TV/DBS DVD/LD POWER TAPE (MD) MONITOR TUNER PHONO CD 6 A/B/C/D/E PHONES SPEAKERS A B BASS TREBLE BALANCE FM/AM DOWN TUNING DELAY/ CENTER CENTER/REAR MODE TUNING MEMORY EDIT MODE TIME/LEVEL UP ON OFF L 5 5 R MAN'L/AUTO FM AUTO/MAN'L MONO 9 A B C D FG I J K E H RX-V9 1 5 NATURAL SOUND AV RECEIVER RX V9 CINEMA DSP VOLUME TAPE (MD) MONITOR VCR VIDEO 6 POWER TUNER PHONO CD 6 A/B/C/D/E PHONES SPEAKERS A B BASS TREBLE BALANCE FM/AM DOWN TUNING UP EFFECT CENTER MODE TUNING MEMORY EDIT MODE PROGRAM CENTER LEVEL REAR LEVEL ON OFF L 5 5 R MAN'L/AUTO FM AUTO/MAN'L MONO 1 9 A B C D FG I L K M N E H 7

17 1 POWER switch Press this switch to switch the power on. Press it again to switch the power off. Standby mode indicator (Except U.S.A. and Canada modes) Whie the power is on, pressing the SYSTEM POWER OFF key on the remote contro transmitter switches the unit to the standby mode. In this mode, this indicator is iuminated. SPEAKERS switches Set the switch A or B (or both A and B) for the main speaker system (connected to this unit) you wi use to the ON position. Set the switch for the main speaker system you wi not use to the OFF position. A A/B/C/D/E button Press this button to seect a desired group (A E) of preset stations. Engish Remote contro sensor Receives signas from the remote contro transmitter. Dispay pane Shows various information. (Refer to page 17 for detais.) 5 Input seector buttons Seect a program source to isten to or watch. When a button is pressed, the name of seected source appears on the dispay. 6 DSP program seector buttons RX-V9 ony Seect a DSP program. When a button is pressed, the name of seected program ights up on the dispay. 7 EFFECT button Switches on/off the digita sound fied processor (incuding the Doby Pro Logic Surround decoder). VOLUME contro Used to raise or ower the voume eve. 9 PHONES jack When you isten with headphones, connect the headphones to the PHONES jack. You can isten to the sound to be output from the main speakers through headphones. When istening with headphones privatey, set both the SPEAKERS A and B switches to the OFF position and switch off the digita sound fied processor (so that no DSP program name is iuminated on the dispay) by pressing the EFFECT button. B Preset station number seector buttons Seect a preset station number (1 to ). C Tone contros These contros are effective ony for the sound from the main speakers. BASS Used to increase or decrease the ow frequency response. The position produces fat response. TREBLE Used to increase or decrease the high frequency response. The position produces fat response. D BALANCE contro Adjusts the baance of the output voume to the eft and right speakers to compensate for sound imbaance caused by speaker ocation or istening room conditions. E FM/AM buttons Press this button to switch the reception band to FM or AM. PHONES 15

18 F MEMORY (MAN L/AUTO FM) button When this button is pressed, the MEMORY indicator fashes for about 5 seconds. During this period, seect a desired preset station number by pressing the corresponding preset station number seector button to enter the dispayed station into the memory. When this button is pressed and hed for about seconds, the automatic preset tuning begins. (Refer to page for detais.) G EDIT button This button is used to exchange the paces of two preset stations with each other. H TUNING DOWN/UP button Used for tuning. Press the UP side to tune in to higher frequencies, and press the DOWN side to tune in to ower frequencies. I TUNING MODE (AUTO/MAN L MONO) button Press this button to switch the tuning mode to automatic or manua. To seect the automatic tuning mode, press this button so that AUTO ights up on the dispay. To seect the manua tuning mode, press this button so that AUTO goes off. J DELAY/CENTER/REAR and TIME/LEVEL +/ buttons RX-V9 ony Adjust the deay time (DELAY), the rear channe output eve (REAR) and the center channe output eve (CENTER). Seect the item which you want to adjust by pressing the DELAY/CENTER/REAR button and adjust its time or eve by pressing the TIME/LEVEL +/ button. K CENTER MODE button Seects a center channe output mode (NORMAL, WIDE or PHANTOM). (For detais, refer to page 1.) L PROGRAM seector button RX-V9 ony When the buit-in digita sound fied processor (incuding the Doby Pro Logic Surround decoder) is on, this button changes the currenty seected DSP program whenever the right or eft side of this button is pressed. M CENTER LEVEL contro RX-V9 ony Adjusts the sound output eve of the center speaker. N REAR LEVEL contro RX-V9 ony Adjusts the sound output eve of the rear speakers. 16

19 DISPLAY PANEL Engish 1 56 PRESET MEMORY AUTO TAPE MON ms db khz MHz PRO LOGIC ENHANCED STEREO SLEEP NORM WIDE PHANTOM EFFECT OFF CONCERT MONO DISCO ROCK CONCERT VIDEO MOVIE STADIUM CONCERT HALL Muti-information dispay Dispays various information, for exampe station frequency, preset station number and name of seected input source. STEREO indicator Lights up when an FM stereo broadcast with sufficient signa strength is received. Signa-eve meter Indicates the signa eve of the received station. If mutipath interference is detected, the indication decreases. 9 TAPE MON indicator Lights up when the tape deck (or MD recorder etc.) is seected as the input source by pressing the TAPE (MD) MONITOR button. DSP program indicators The name of a seected DSP program ights up when the buitin digita sound fied processor and/or the Doby Pro Logic Surround decoder is on. SLEEP indicator Lights up whie the buit-in SLEEP timer is functioning. 5 Center channe mode indicators The name of a seected center channe mode ights up ony when a program which uses the Doby Pro Logic Surround decoder is seected. 6 EFFECT OFF indicator Lights up if neither the digita sound fied processor nor the Doby Pro Logic Surround decoder is on. In this state, sound output is -channe stereo. 7 AUTO indicator Lights up when this unit is in the automatic tuning mode. MEMORY indicator When the MEMORY button is pressed, this indicator fashes for about 5 seconds. During this period, the dispayed station can be programmed to the memory by using the A/B/C/D/E button and the preset station number seector buttons. 17

20 REMOTE CONTROL TRANSMITTER The remote contro transmitter provided with this unit is designed to contro a the most commony used functions of this unit. If the CD payer and tape deck connected to this unit are YAMAHA components designed for remote contro compatibiity, then this remote contro transmitter wi aso contro various functions of each component. RX-V9 RX-V TIME/ DELAY/CENTER LEVEL /REAR TEST EFFECT + PROGRAM PROLOGIC ENHANCED ON/OFF VCR TV/DBS DVD/LD 7 1 DELAY TIME+ TEST EFFECT PROGRAM PROLOGIC ENHANCED ON/OFF VCR VIDEO 7 1 DIR A DIR B REC/PAUSE PLAY A/B PRESET + A/B/C/D/E DISC PLAY TAPE TUNER CD PHONO 6 1 DIR A DIR B REC/PAUSE PLAY A/B PRESET + A/B/C/D/E DISC PLAY TAPE TUNER CD PHONO 6 SLEEP POWER VOLUME SLEEP POWER VOLUME 5 5 1

21 For Contro of This Unit 1 DELAY/CENTER/REAR and TIME/LEVEL +/ keys RX-V9 ony Adjust the deay time (DELAY), the rear channe output eve (REAR) and the center channe output eve (CENTER). Seect the item which you want to adjust by pressing the DELAY/CENTER/REAR key and adjust its time or eve by pressing the TIME/LEVEL +/ key. DELAY TIME +/ key RX-V9 ony Adjusts the deay time, or the time difference between the begining of source sound and the begining of effect sound. (For detais, refer to page.) Tuner keys Contros tuner. +: Seects higher preset station number. : Seects ower preset station number. A/B/C/D/E: Seects the group (A E) of preset station numbers. For Other Component Contro Identify the remote contro transmitter keys with your component s keys. If these keys are identica, their functions wi be the same. On each key function, refer to the corresponding instruction on your component s manua. 1 Tape deck keys Contros tape deck. * DIR A, B and A/B are appicabe ony to doube cassette tape deck. * For a singe cassette deck with automatic reverse function, pressing DIR A wi reverse the direction of tape running. CD payer keys Contros compact disc payer. * DISC is appicabe ony to compact disc changer. Engish SLEEP timer key This key is used to turn the buit-in SLEEP timer on and off, and to set the SLEEP time. (See page for detais.) POWER key Turns the power on/off. * (Except U.S.A. and Canada modes) Whie the power is on, pressing the POWER key on the remote contro transmitter switches the unit from the poweron mode to the standby mode, and vice versa. (In the standby mode, the standby mode indicator on the front pane is iuminated.) 5 VOLUME +/ keys Turns the voume eve up/down. 6 Input seector keys Seects input source. 7 Program seector keys PROGRAM: When the buit-in digita sound fied processor (incuding the Doby Pro Logic Surround decoder) is on, this key changes the currenty seected DSP program whenever the right or eft side of this key is pressed. PROLOGIC: Directy seects the ENHANCED: Directy seects the PRO LOGIC program. PRO LOGIC ENHANCED program. EFFECT ON/OFF key Switches on/off the digita sound fied processor (incuding the Doby Pro Logic Surround decoder). 9 TEST key Used for speaker baance adjustment. (For detais, refer to page.) 19

22 6 6 REC/PAUSE SPEAKER BALANCE ADJUSTMENT This procedure ets you adjust the sound output eve baance between the main, center, and rear speakers using the buit-in test tone generator. When this adjustment is performed, the sound output eve heard at the istening position wi be the same from each speaker. This is important for the best performance of the digita sound fied processor and the Doby Pro Logic Surround decoder. 1 RX-V9 5 RX-V9 5 TIME/ DELAY/CENTER LEVEL + /REAR TEST EFFECT DELAY TIME+ TEST EFFECT PROGRAM PROLOGIC ENHANCED ON/OFF PROGRAM PROLOGIC ENHANCED ON/OFF VCR TV/DBS DVD/LD VCR VIDEO DIR A DIR B PLAY DIR A DIR B REC/PAUSE PLAY A/B TAPE A/B TAPE PRESET + A/B/C/D/E TUNER PRESET + A/B/C/D/E TUNER SLEEP POWER DISC PLAY VOLUME CD PHONO SLEEP POWER DISC PLAY VOLUME CD PHONO 1 VOLUME 6 Seect the main speakers to be used. SPEAKERS A B ON OFF 6 Set to the position. Turn the power on. * If you use two main speaker systems, press both the A and B switches. BASS TREBLE BALANCE POWER L 5 5 R 5 TEST Set to the position.

23 6 6 RX-V9 RX-V9 Engish TIME/ DELAY/CENTER LEVEL + /REAR TEST EFFECT DELAY TIME+ TEST EFFECT PROGRAM PROLOGIC ENHANCED ON/OFF PROGRAM PROLOGIC ENHANCED ON/OFF VCR TV/DBS DVD/LD VCR VIDEO DIR A DIR B REC/PAUSE PLAY DIR A DIR B REC/PAUSE PLAY A/B TAPE A/B TAPE PRESET + A/B/C/D/E TUNER PRESET + A/B/C/D/E TUNER DISC PLAY CD DISC PLAY CD PHONO PHONO 6 7 SLEEP POWER VOLUME SLEEP POWER VOLUME Seect the center channe output mode suitabe for your speaker configuration. (Refer to SPEAKER CONFIGURATION on page 7.) 7 Turn up the voume. VOLUME 6 CENTER MODE NORMAL WIDE 6 PHANTOM On the feature of each mode, refer to the Note shown beow. Note In step 6, when you seect a center channe output mode, note the foowing. For 5 speaker configuration) NORMAL: Seect this mode when you use a center speaker that is smaer than the main speakers. In this mode, the bass tone wi be output from the main speakers. WIDE: Seect this mode when you use the center speaker approximatey same sized as the main speakers. For speaker configuration) PHANTOM: Seect this mode when you do not use the center speaker. The center sound wi be output from the eft and right main speakers. You wi hear a test tone (ike pink noise) from the eft main speaker, then the center speaker, then the right main speaker, and then the rear speakers, for about two seconds each. The dispay changes as shown beow. Main (L) Rear (L and R) Center Main (R) * The test tone from the eft rear speaker and the right rear speaker wi be heard at the same time. Adjust the BALANCE contro so that the effect sound output eve of the eft main speaker and the right main speaker are the same. BALANCE L 5 5 R CONTINUED 1

24 6 6 RX-V9 TIME/ LEVEL + 9 DELAY/CENTER /REAR TEST EFFECT PROGRAM PROLOGIC ENHANCED ON/OFF 1 RX-V9 DELAY TIME+ TEST EFFECT PROGRAM PROLOGIC ENHANCED ON/OFF 1 VCR TV/DBS DVD/LD VCR VIDEO DIR A DIR B REC/PAUSE PLAY DIR A DIR B REC/PAUSE PLAY A/B TAPE A/B TAPE PRESET + A/B/C/D/E TUNER PRESET + A/B/C/D/E TUNER DISC PLAY CD DISC PLAY CD SLEEP POWER VOLUME PHONO 9 SLEEP POWER VOLUME PHONO 9 Adjust the sound output eves of the center speaker and the rear speakers so that they become amost as same as that of the main speakers. 1 Cance the test tone. TEST RX-V9 Make the adjustment of each speaker output eve at your istening position with the remote contro transmitter. a) Press once or more so that CENTER or REAR appears on the dispay. * Seect CENTER to adjust the output eve of the center speaker, and seect REAR to adjust the output eve of the rear speakers. DELAY/CENTER /REAR/SWFR b) Adjust its eve. * Pressing the + side raises and the side owers the eve. TIME/ LEVEL + Notes Disappears. Once you have competed these adjustments, you can adjust whoe sound eve on your audio system by using the VOLUME contro (or the VOLUME keys on the remote contro transmitter) ony. If you use externa power ampifiers, you may aso use their voume contros to achieve proper baance. RX-V9 ony In step 9, if the center channe mode is in the PHANTOM position, the sound output eve of the center speaker cannot be adjusted. This is because in this mode, the center sound is automaticay output from the eft and right main speakers. RX-V9 CENTER LEVEL REAR LEVEL

25 6 6 TO PLAY A SOURCE BASIC OPERATIONS 1, 6 Engish 7 1 VOLUME 6 5 Pay the source. (For detaied information on the tuning operation, refer to page 6.) 6 VOLUME 6 6 Set to the position. 6 Turn the power on. POWER Adjust to the desired output eve. 7 If desired, adjust the BASS, TREBLE and BALANCE contros (refer to page 5), and use the digita sound fied processor. (Refer to page 1.) Seect the desired input source by using the input seector buttons. (For video sources, turn the TV/monitor ON.) TUNER PHONO * The name of the seected input source wi appear on the dispay. Seect the main speakers to be used. SPEAKERS A B CD Notes on using the input seector buttons Note that pressing on each input seector button seects the source which is connected to the corresponding input terminas on the rear pane. The seection of TAPE (MD) MONITOR cannot be canceed by pressing another input seector button. To cance it, press TAPE (MD) MONITOR again so that TAPE MON disappears from the dispay. When you seect a button other than TAPE (MD) MONITOR, make sure that TAPE MON is not iuminated on the dispay. If you seect the input seector button for a video source without canceing the seection of TAPE (MD) MONITOR, the payback resut wi be the video image from the video source and the sound from the audio tape (or MD etc.). Once you pay a video source, its video image wi not be interrupted even if the input seector button for an audio source is seected. ON OFF * If you use two main speaker systems, press both the A and B switches. To turn off the power Press the POWER switch again.

26 TO RECORD A SOURCE TO TAPE (OR MD) RX-V9 RX-V Seect the source to be recorded. Begin recording on the tape deck (or MD recorder etc.) or VCR connected to this unit. TUNER PHONO CD If the tape deck (or MD recorder etc.) is used for recording, you can monitor the sounds being recorded by pressing TAPE (MD) MONITOR so that TAPE MON ights up on the dispay. Pay the source and then turn the VOLUME contro up to confirm the input source. (For detaied information on the tuning operations, refer to the page 6.) RX-V9 TV/DBS DVD/LD RX-V9 TAPE (MD) MONITOR VCR VOLUME 6 TAPE (MD) MONITOR PHONO CD TUNER PHONO 6 Note The settings of DSP and the VOLUME, BASS, TREBLE and BALANCE contros have no effect on the materia being recorded.

27 Seecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches aow you to seect speaker system A or B, or both at once. SPEAKERS A B Adjusting the BASS and TREBLE contros BASS 5 5 TREBLE 5 5 Engish ON OFF BASS : Turn this cockwise to increase (or countercockwise to decrease) the ow frequency response. Adjusting the BALANCE contro Adjust the baance of the output voume to the eft and right speakers to compensate for sound imbaance caused by speaker ocation or istening room conditions. BALANCE TREBLE : Turn this cockwise to increase (or countercockwise to decrease) the high frequency response. Note These contros are effective ony for the sound from the main speakers. L 5 5 R Note This contro is effective ony for the sound from the main speakers. 5

28 6 6 TUNING OPERATIONS Normay, if station signas are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possibe. However, if signas of the station you want to seect are weak, you must tune to it manuay (MANUAL TUNING). AUTOMATIC TUNING 1 MANUAL TUNING 1 Seect the reception band (FM or AM) confirming it on the dispay. 1 Seect the reception band (FM or AM) confirming it on the dispay. FM/AM FM/AM or or TUNING MODE TUNING MODE AUTO/MAN L MONO AUTO AUTO/MAN L MONO Turn AUTO off. DOWN TUNING UP Tune to a desired station manuay. DOWN TUNING UP To tune to a higher frequency, press the right side once. To tune to a ower frequency, press the eft side once. * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signas of the station are weak), change to the MANUAL TUNING method. * To continue tuning search, press and hod the button. Note If you tune to an FM station manuay, it is received in monaura mode automaticay to increase the signa quaity. 6

29 6 6 MANUAL PRESET TUNING PRESET TUNING Engish This unit can store station frequencies seected by tuning operation. With this function, you can reca any desired station by ony seecting the preset station number where it is stored. Up to stations ( stations x 5 groups) can be stored. To store stations, 1, To reca a preset station 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) 1 Seect the group of preset stations. A/B/C/D/E Seect a desired group (A E) of preset stations confirming it on the dispay. A/B/C/D/E PRESET Seect the preset station number MEMORY MAN L/AUTO FM MEMORY Fashes on and off for about 5 seconds. Seect a preset station number where you want to program the station before MEMORY goes off from the dispay PRESET AUTO MHz STEREO CONCERT HALL Notes A new setting can be programmed in pace of the former one. For presets, the setting of the reception mode (stereo or monaura) is stored aong with the station frequency. Memory back-up The memory back-up circuit prevents the programmed data from being ost even if the POWER switch is set off or the power pug is disconnected from the AC outet or the power is cut due to temporary power faiure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simpy foowing the PRESET TUNING steps. Shows the dispayed station has been programmed to A1. * In the same way, program other stations to A, A... A. * You can program more stations to preset station numbers on other groups in the same way by seecting other groups in step. 7

30 6 6 AUTOMATIC PRESET TUNING You can aso make use of an automatic preset tuning function for FM stations ony. By this function, this unit performs automatic tuning and stores FM stations with strong signas sequentiay. Up to stations are stored automaticay in the same way as in the manua preset tuning method on page 7. To store stations 1 1 FM/AM When the automatic preset tuning is finished The dispay shows the frequency of the ast preset station. Check the contents and the number of preset stations by foowing the procedure of the section To reca a preset station on page 7. MEMORY MAN L/AUTO FM Press and hod for about seconds. DOWN TUNING UP PRESET MEMORY AUTO Fashes. To reca a preset station Simpy foow the procedure of the section To reca a preset station on page 7. Notes You can repace a preset station by another FM or AM station manuay by simpy foowing the procedure of the section To store stations on page 7. If the number of received stations is not enough to be stored up to E, the search is finished automaticay after searching a frequencies. With this function, ony FM stations with sufficient signa strength are stored automaticay. If the station you want to program is weak in signa strength, tune to it in monaura manuay and program it by foowing the procedure of the section To store stations on page 7. To tune to higher frequencies, press right side once. To tune to ower frequencies, press eft side once. * If the TUNING button is not pressed, in a whie, the automatic preset tuning begins automaticay toward higher frequencies. The automatic preset tuning begins from the frequency currenty dispayed. Received stations are programmed to A1, A... A sequentiay. * If more than stations are received, they are aso programmed to the preset station numbers on other groups (B, C, D and E) in that order. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for exampe, you want to store the first received station to C5, seect C5 by using the A/B/C/D/E button and the preset station number seector buttons after pressing the MEMORY button in step. Then press the TUNING button. The first received station is stored to C5, and next stations to C6, C7... sequentiay. If stations are stored up to E, the automatic preset tuning is finished automaticay.