Operation Guide

Transcription

1 MO0806-E Getting cquainted Congratuations upon your seection of this CSIO watch. To get the most out of your purchase, be sure to carefuy read this manua and keep it on hand for ater reference when necessary. This watch does not have a time zone that corresponds to the Greenwich Mean Time differentia of 3.5 hours. Because of this, the radio-controed timekeeping and Word Time functions wi not dispay the correct time for Newfoundand, Canada. Keep the watch exposed to bright ight The eectricity generated by the soar ce of the watch is Bright Light stored by a buit-in battery. Leaving or using the watch where it is not exposed to ight causes the battery to run down. Make sure the watch is exposed to ight as much as Soar ce possibe. When you are not wearing the watch on your wrist, position the face so it is pointed at a source of bright ight. You shoud try to keep the watch outside of your seeve as much as possibe. Charging is reduced significanty if the face is ony partiay covered. The watch continues to operate, even when it is not exposed to ight. Leaving the watch in the dark can cause the battery to run down, which wi resut in some watch functions to be disabed. If the battery goes dead, you wi have to re-configure watch settings after recharging. To ensure norma watch operation, be sure to keep it exposed to ight as much as possibe. Battery charges in the ight. Battery discharges in the dark. Soar ce (Converts ight to eectrica power.) Bright Light Eectrica energy The actua eve at which some functions are disabed depends on the watch mode. Frequent dispay iumination can run down the battery quicky and require charging. The foowing guideines give an idea of the charging time required to recover from a singe iumination operation. pproximatey 5 minutes exposure to bright sunight coming in through a window pproximatey 50 minutes exposure to indoor fuorescent ighting Be sure to read Power Suppy for important information you need to know when exposing the watch to bright ight. If the digita dispay of the watch is bank... If the Power Saving indicator (PS) is fashing on the dispay, it means that the dispay is bank because the watch s Power Saving function has turned it off to conserve power. Power Saving automaticay turns off the dispay and enters a seep state whenever your watch is eft for a certain period in an area where it is dark. If the watch is kept in the dark for a onger period, the anaog hands wi aso stop moving after a few days. The initia factory defaut setting is Power Saving on. The watch wi recover from the seep state if you move it to a we-it area or if you press any button. See Power Saving Function for more information. bout This Manua Modue 3311 The operationa procedures for Modues 3311 and 5052 are identica. of the iustrations in this manua show Modue Button operations are indicated using the etters shown in the iustration. Each section of this manua provides you with the information you need to perform operations in each mode. Further detais and technica information can be found in the Reference section. LEVEL 1 LEVEL 2 LEVEL 3 Charge LEVEL 4 functions enabed LEVEL 1 LEVEL 2 Discharge LEVEL LEVEL 3 4 Some or a functions disabed Rechargeabe battery Modue 5052 Genera Guide Press C to change from mode to mode. In any mode, press B to iuminate the dispay. Battery Leve Indicator Word Time Mode Timekeeping Mode Press C. or Hand Setting Mode Stopwatch Mode arm Mode Radio-controed tomic Timekeeping Hour hand This watch receives a time caibration signa and updates Minute hand its time setting accordingy. The time caibration signa incudes both Standard Time and Dayight Saving Time (summer time) data. This watch is designed to pick up the time caibration signa transmitted in the United States (Fort Coins, Coorado) and the time caibration signas transmitted in Japan. The U.S. time caibration signa can be picked up by the watch whie in North merica.* * The term North merica in this manua refers to the Day area that consists of Canada, the continenta United Day of week States, and Mexico. Second hand Current Time Setting This watch automaticay adjusts its time setting in accordance with a time caibration signa. You can aso perform a manua procedure to set the time and date, when necessary. The first thing you shoud do after purchasing this watch is to set your Home City, which is the city where you wi normay use the watch. For more information, see To set your Home City beow. When using the watch outside the ranges of the U.S. and Japanese time signa transmitters, you have to adjust the current time setting manuay as required. See Timekeeping for more information about manua time setting. The anaog time of this watch is synchronized with the digita time. Because of this, the anaog time setting is automaticay adjusted whenever you change the digita setting. See naog Timekeeping for more information. To set your Home City Transmitter indicator 1. In the Timekeeping Mode, hod down unti the transmitter indicator (US) starts to fash, which indicates the The second hand wi move at high speed to the 12 o cock position, where it wi stop. 2. Press C once so the city code is fashing on the dispay. 3. Use D (east) and B (west) to scro through the city codes unti the one you want to use as your Home City is dispayed. HNL: Honouu NC: nchorage LX: Los ngees, San Francisco, Las Vegas, Seatte, Vancouver, Tijuana DEN: Denver, E Paso, Edmonton, Cuiacan CHI: Chicago, Houston, Daas/Fort Worth, New Oreans, Winnipeg, Mexico City NYC: New York, Detroit, Miami, Boston, Montrea TYO: cities in Japan SEL: Seou HKG: Hong Kong that this watch does not have a city code that corresponds to Newfoundand. 4. Press twice to exit the The first press of dispays the 12/24-hour Pressing again exits the The second hand wi advance at high speed to the correct position in accordance with seconds count of the digita time, and resume norma movement from there. Normay, your watch shoud show the correct time as soon as you seect your Home City Code. If it does not, it shoud adjust automaticay after the next auto receive (in the midde of the night). You can aso perform manua receive or you can set the time manuay. If you are in an area that does not use Dayight Saving Time (summer time), turn off the DST setting. To dispay the digita time and ast signa screen In the Timekeeping Mode, press to cyce through the digita time screens as shown beow. In the Timekeeping Mode, press D to dispay the ast signa screen. The ast signa screen shows the date and time of the ast successfu time caibration signa reception. Date Screen Receiving Indicator Day and Seconds Count Receiving indicator Day of week Last Signa Screen Press. Reception date Current Time Screen Seconds Hour : Minutes PM indicator Reception Time 1

2 Time Caibration Signa Reception There are two different methods you can use to receive the time caibration signa: auto receive and manua receive. uto Receive With auto receive, the watch automaticay picks up the time caibration signa five times a day at 0:00 a.m., 1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. For more information, see bout uto Receive. Manua Receive Manua receive ets you start time caibration signa reception with the press of a button. For more information, see To perform manua receive. Important! When getting ready to receive the time caibration signa, position the watch as shown in the nearby iustration, with its 12 o cock side facing towards a window. This watch is designed to receive a time caibration signa ate at night. Because of this, you shoud pace the watch near a window as shown in the iustration when you take it off at night. Make sure there are no meta objects nearby. When auto receive is turned on, the watch receives the caibration signa for two to seven minutes everyday when the time in the Timekeeping Mode reaches each of the five caibration times. Do not perform any button operation within seven minutes before or after any of the five caibration times. Doing so can interfere with correct caibration. Remember that reception of the caibration signa depends on the time kept in the digita dispay. The reception wi be performed whenever the dispay shows one of the five caibration times, regardess of whether or not the dispayed time is actuay the correct time. When two, three, four, or five receptions are successfu, the watch uses the data of the ast reception for caibration. When ony one reception is successfu, the watch uses the data of the successfu reception. bout the Receiving Indicator The receiving indicator shows the strength of the caibration signa being received. For best reception, be sure to keep the watch in a ocation where signa strength is strongest. Receiving indicator Resin Band Meta Band Weak Strong (Leve 1) (Leve 4) Make sure the watch is facing the right way. Proper signa reception can be difficut or even impossibe under the conditions isted beow. Inside or among buidings Inside a vehice Near househod appiances, office equipment, or a mobie phone Near a construction site, airport, or other sources of eectrica noise Near hightension power ines mong or behind mountains Signa reception is normay better at night than during the day. Time caibration signa reception takes from two to seven minutes. Take care that you do not perform any button operations or move the watch during this time. When within range of the appicabe transmitter, this watch can receive either the U.S. (Fort Coins, Coorado) or Japanese (Fukushima or Fukuoka/Saga) time caibration signa. The signa the watch wi attempt to pick up depends on its current Home City code setting as shown beow. Home City Code Transmitter Frequency HNL*, NC*, LX, DEN, Fort Coins, Coorado 60kHz CHI, NYC TYO**, SEL*, HKG* Fukushima 40kHz Fukuoka/Saga 60kHz * The areas covered by the SEL, HKG, HNL, and NC city codes are quite far from the time caibration signa transmitters, and so certain conditions may cause probems with signa reception. With TYO, you can specify either 40kHz or 60kHz. ** 600 mies 2,000 mies Fukuoka/Saga 1,000 kiometers Fort Coins 500 kiometers 500 kiometers Fukushima 1,000 kiometers Under good reception conditions, signa reception is possibe within a radius of about 2,000 mies (3,000 kiometers) from the Fort Coins transmitter. t distances further than about 600 mies (1,000 kiometers) from the Fort Coins transmitter, signa reception may not be possibe during certain times of year or times of day. Radio interferance may aso cause probems with reception. t distances further than about 500 kiometers from the Fukushima and Fukuoka/ Saga transmitter, signa reception may not be possibe during certain times of year or times of day. Radio interferance may aso cause probems with reception. Even when the watch is within the reception range of the transmitter, signa reception wi be impossibe if the signa is bocked by mountains or other geoogica formations between the watch and signa source. Signa reception is affected by weather, atmospheric conditions, and seasona changes. See the information under Signa Reception Troubeshooting if you experience probems with time caibration signa reception. bout uto Receive When auto receive is turned on, the watch automaticay starts to receive the time caibration signa when the time in the Timekeeping Mode reaches 0:00 a.m., 1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. each day (caibration times). The watch wi aso perform an additiona auto receive at 5:00 a.m. if none of the reguary schedued auto receive are successfu. uto receive is performed ony if the watch is in the Timekeeping Mode or Word Time Mode when one of the caibration times is reached. It is not performed if a caibration time is reached whie an aarm is sounding, or whie you are configuring settings (whie settings are fashing on the dispay). When a reception starts, the second hand wi move at high speed to the 12 o cock position where it wi stop unti the reception is compete. uto receipt of the caibration signa is designed to be performed eary in the morning, whie you seep (provided that the Timekeeping Mode time is set correcty). Before going to bed for the night, remove the watch from your wrist, and put it in a ocation where it can easiy receive the signa. Even in an area where signa strength is strong, it takes about 10 seconds for signa reception to stabiize enough for the receiving indicator to indicate signa strength. Use the receiving indicator as a guide for checking signa strength and for finding the best ocation for the watch during signa reception. The Leve 4 receiving indicator appears on the Timekeeping Mode s Receiving Indicator and Seconds Count screen ony. The Leve 4 receiving indicator is not dispayed if signa reception was unsuccessfu or after manua adjustment of the current time setting. The Leve 4 receiving indicator indicates that at east one of the five caibration signa reception was successfu., however, that the Leve 4 receiving indicator is ceared from the dispay at 3:00 a.m. each day. To perform manua receive 1. Pace the watch on a stabe surface so its top (12 Receiving indicator o cock side) is facing towards a window. 2. In the Timekeeping Mode, hod down D for about two seconds unti the watch beeps. 3. Reease D and RC fashes to indicate that signa reception has started. When a reception starts, the second hand wi move at high speed to the 12 o cock position where it wi stop unti the reception is compete. Time caibration signa reception normay takes from two to seven minutes. In Japan, however, reception can take up to 14 minutes. Take care that you do not perform any button operations or move the watch during this time. fter signa reception is compete, the dispay of the watch changes to the ast signa screen. To interrupt a reception and return to the Timekeeping Mode, press D. If the reception is unsuccessfu, the message ERR appears on the dispay for about one or two minutes. fter that, the watch returns to the Timekeeping Mode. You can aso change from the ast signa or ERR screen to the norma timekeeping screen by pressing D. To turn auto receive on and off 1. In the Timekeeping Mode, hod down unti the transmitter indicator starts to fash, which indicates the On/off status The second hand wi move at high speed to the 12 o cock position, where it wi stop. 2. Press C three times to move the fashing to the auto receive on/off setting. 3. Press D to togge auto receive on ( ON) and off ( OF). If the current Home City setting is a city code that does not support auto receive, -- appears in pace of the on/off indicator. This means you cannot turn auto receive on or off. 4. Press twice to exit the The second hand wi advance at high speed to the correct position in accordance with the digita time seconds count, and resume norma movement from there. For information about city codes that support signa reception, see To set your Home City. Signa Reception Troubeshooting Check the foowing points whenever you experience probems with signa reception. Probem Cannot perform manua receive. uto receive is turned on, but the Leve 4 receiving indicator does not appear on the Timekeeping Mode dispay. Time setting is incorrect foowing signa reception. Probabe Cause The watch is not in the Timekeeping Mode. Your current Home City is not one of the foowing city codes: HNL, NC, LX, DEN, CHI, NYC, HKG, SEL, or TYO. You changed the time setting manuay. The watch was not in the Timekeeping or Word Time Mode, or you were performing some button operation during the auto receive. Even if reception is successfu, the Leve 4 receiving indicator disappears every day at 3 a.m. Time data (hour, minutes, seconds) ony was received during the ast reception. The Leve 4 receiving indicator appears ony when time data and date data (year, month, day) are both received. If the time is one hour off, the DST setting may be incorrect. The Home City code setting is not correct for the area where you are using the watch. What you shoud do Enter the Timekeeping Mode and try again. Seect HNL, NC, LX, DEN, CHI, NYC, HKG, SEL, or TYO as your Home City. Perform manua receive or wait unti the next auto receive is performed. Check to make sure the watch is in a ocation where it can receive the signa. Change the DST setting to uto DST. Seect the correct Home City code. For further information, see Important! under Time Caibration Signa Reception and Radio-controed tomic Timekeeping Precautions. 2

3 Word Time City Code Current time in the seected city code The Word Time Mode digitay dispays the current time in 30 cities (29 time zones) around the word. Pressing in the Word Time Mode causes the appicabe city code to appear on the digita dispay for about two seconds. If the current time shown for a city is wrong, check your Home City time settings and make the necessary changes. The watch wi perform a signa reception even if it is in the Word Time Mode when a caibration time is reached. If this happens, the Word Time Mode time settings wi be adjusted in accordance with the Timekeeping Mode s Home City time. of the operations in this section are performed in the Word Time Mode, which you enter by pressing C. To view the time in another city Whie in the Word Time Mode, press D to scro through the city codes (time zones). For fu information on city codes, see the City Code Tabe. To togge a city code time between Standard Time and Dayight Saving Time 1. In the Word Time Mode, use D to dispay the city code (time zone) whose Standard Time/Dayight Saving Time setting you want to change. Pressing in the Word Time Mode causes the appicabe city code to appear on the digita dispay for about two seconds. 2. Hod down to togge Dayight Saving Time (DST indicator dispayed) and Standard Time (DST indicator not dispayed). DST indicator that you cannot use the Word Time Mode to change the DST setting of the Home City code you currenty have seected in the Timekeeping Mode. See To change the Dayight Saving Time (summer time) setting for information about turning the Home City code DST setting on and off. The DST indicator wi appear on the dispay whenever you dispay a city code for which Dayight Saving Time is turned on. that you cannot switch between Standard Time and Dayight Saving Time whie GMT is seected as the city code. that the DST/Standard Time setting affects ony the currenty dispayed city code. Other city codes are not affected. arms On/Off status You can set three independent Daiy arms. When an aarm is turned on, the aarm tone sounds when the aarm arm Mode number indicator time is reached. You can aso turn on an Houry Time Signa that causes the watch to beep twice every hour on the hour. The aarm and Houry Time Signa operate in accordance with the current digita time. The aarm number (L1 though L3) indicates an aarm screen. SIG appears in pace of the aarm number when the Houry Time Signa screen is shown. ternate at of the operations in this section are performed in the two-second arm Mode, which you enter by pressing C. interva Stopwatch 1/100 Seconds second More than one minute Minutes Seconds Spit Time Screen Spit indicator The stopwatch ets you measure eapsed time, spit times, and two finishes. The dispay range of the stopwatch is 99 minutes, seconds. The 1/100-second vaue appears whie the eapsed time operation is stopped or whie a spit time is frozen on the dispay. Eapsed Time Screen Eapsed time (Minutes : Seconds) Spit time (Minutes : Seconds) 1/100 second 1/100 second The stopwatch continues to run, restarting from zero after it reaches its imit, unti you stop it. Exiting the Stopwatch Mode whie a spit time is frozen on the dispay cears the spit time and returns to eapsed time measurement. The stopwatch measurement operation continues even if you exit the Stopwatch Mode. of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. To measure times with the stopwatch Eapsed Time D Start Spit Time D Start Two Finishes D Start Iumination D Stop Spit Spit First runner finishes. Dispay time of first runner. D D Re-start Stop Cear D Spit reease Stop Cear D Stop Spit reease Cear Second runner Dispay time of finishes. second runner. n LED (ight-emitting diode) and a ight guide pane iuminate the digita dispay for easy reading in the dark. See Iumination Precautions for other important information. arm time (Hour : Minutes) To set an aarm time 1. In the arm Mode, press D to seect the aarm whose time you want to set. To iuminate the dispay In any mode, press B to iuminate the dispay. You can specify 1.5 seconds or 2.5 seconds as the iumination duration. See To set the current digita time and date manuay for more information. L1 L2 L3 SIG 2. Hod down unti the hour setting of the aarm time starts to fash, which indicates the This automaticay turns on the aarm. 3. Press C to move the fashing between the hour and minute settings. 4. Whie a setting is fashing, use D (+) and B ( ) to change it. When setting the aarm time using the 12-hour format, take care to set the time correcty as a.m. (no indicator) or p.m. (P indicator). If you have 24-hour timekeeping seected in the Timekeeping Mode, the aarm time is aso dispayed in 24-hour format. 5. Press to exit the arm Operation The aarm sounds in a modes at the preset time for about 10 seconds, or unti you stop it by pressing any button. To test the aarm In the arm Mode, hod down D to sound the aarm. To turn an aarm and the Houry Time Signa on and off 1. In the arm Mode, press D to seect an aarm or the Houry Time Signa. 2. When the aarm or the Houry Time Signa you want to set is seected, press to turn it on and off. Power Suppy This watch is equipped with a soar ce and a specia rechargeabe battery (secondary battery) that is charged by the eectrica power produced by the soar ce. The iustration shown beow shows how you shoud position the watch for charging. Exampe: Orient the watch so its face is pointing at a ight source. Soar ce The iustration shows how to position a watch with a resin band. that charging efficiency drops when any part of the soar ce is bocked by cothing, etc. You shoud try to keep the watch outside of your seeve as much as possibe. Charging is reduced significanty if the face is ony partiay covered. Important! Storing the watch for ong periods in an area where there is no ight or wearing it in such a way that it is bocked from exposure to ight can cause rechargeabe battery power to run down. Make sure that the watch is exposed to bright ight whenever possibe. This watch uses a specia rechargeabe battery to store power produced by the soar ce, so reguar battery repacement is not required. However, after very ong use, the rechargeabe battery may ose its abiity to achieve a fu charge. If you experience probems getting the specia rechargeabe battery to charge fuy, contact your deaer or CSIO distributor about having it repaced. Never try to remove or repace the watch s specia battery yoursef. Use of the wrong type of battery can damage the watch. The current time and a other settings return to their initia factory defauts whenever battery power drops to Leve 4 and when you have the battery repaced. Turn on the watch s Power Saving function and keep it in an area normay exposed to bright ight when storing it for ong periods. This heps to keep the rechargeabe battery from going dead. 3

4 To check the current battery eve In the Timekeeping Mode, press C once to dispay the battery eve indicator. The battery eve indicator shows the battery eve either as HI (Leve 1) or MID (Leve 2). If the battery eve drops beow Leve 2 (MID), a charge soon aert (Leve 3) is dispayed in a modes. Battery eve indicator Battery Leve Indicator and Charge Indicator The battery eve indicator shows you the current power eve of the rechargeabe battery. Leve Battery Leve Indicator (Charge Soon ert) Function Status functions enabed. functions enabed. uto and manua receive, aarm, houry time signa, iumination, and dispay are disabed. Though the hands of the watch do not move, time continues to be kept internay. functions, incuding timekeeping, disabed. The fashing charge indicator ( C ) at Leve 3 tes you that battery power is very ow, and that exposure to bright ight for charging is required as soon as possibe. t Leve 4, a functions are disabed and settings return to their initia factory defauts. Functions are enabed once again after the rechargeabe battery is charged, but you need to set the time and date, after the battery reaches Leve 2 after dropping to Leve 4. The Home City reverts to TYO (Tokyo), which means that the watch is configured to receive the Japanese time caibration signa, whenever battery power drops to Leve 4. If you are using the watch in North merica, you wi need to configure your Home City code setting whenever battery power recovers after dropping to Leve 4. Leaving the watch in direct sunight or some other very strong ight source can cause the battery eve indicator to temporariy show a reading that is higher than the actua battery eve. The correct battery eve indicator shoud appear after a few minutes. If you use the ight or aarms a number of times during a short period, the recover indicator ( R ) appears on the dispay and the foowing operations become disabed unti battery power recovers. Iumination Beeper tone Coordination between digita and anaog timekeeping Recover indicator Time caibration signa reception fter some time, battery power wi recover and the recover indicator wi disappear, indicating that the above functions are enabed again. Charging Precautions Certain charging conditions can cause the watch to become very hot. void eaving the watch in the areas described beow whenever charging its rechargeabe battery. so note that aowing the watch to become very hot can cause its iquid crysta dispay to back out. The appearance of the LCD shoud become norma again when the watch returns to a ower temperature. Warning! Leaving the watch in bright ight to charge its rechargeabe battery can cause it to become quite hot. Take care when handing the watch to avoid burn injury. The watch can become particuary hot when exposed to the foowing conditions for ong periods. On the dashboard of a car parked in direct sunight Too cose to an incandescent amp Under direct sunight Charging Guide fter a fu charge, timekeeping remains enabed for up to about 5 months. The foowing tabe shows the amount of time the watch needs to be exposed to ight each day in order to generate enough power for norma daiy operations. Exposure Leve (Brightness) Outdoor Sunight (50,000 ux) pproximate Exposure Time 5 minutes Sunight Through a Window (10,000 ux) 24 minutes Dayight Through a Window on a Coudy Day 48 minutes (5,000 ux) Indoor Fuorescent Lighting (500 ux) 8 hours Since these are the specs, we can incude a the technica detais. 5 months (from fu charge to Leve 3 when the watch is not exposed to ight) under the foowing conditions: 1 iumination operation (1.5 seconds) per day 10 seconds of aarm operation per day 5 times caibration reception per day 2 years under the foowing condition: Watch eft in the seep state Stabe operation is promoted by frequent charging. or Recovery Times The tabe beow shows the amount exposure that is required to take the battery from one eve to the next. Exposure Leve pproximate Exposure Time (Brightness) Leve 4 Leve 3 Leve 2 Leve 1 Outdoor Sunight (50,000 ux) 1 hour 10 hours 5 hours Sunight Through a Window (10,000 ux) Dayight Through a Window on a Coudy Day (5,000 ux) 4 hours 8 hours 48 hours 99 hours 22 hours 46 hours Indoor Fuorescent Lighting (500 ux) 76 hours The above exposure time vaues are a for reference ony. ctua required exposure times depend on ighting conditions. Timekeeping Use the Timekeeping Mode to set and view the current time and date. This section aso expains how to manuay set the current date and time. When setting the time, you can aso configure settings for the iumination duration, the 12/24-hour format, and power saving on/off. of the operations in this section are performed in the Timekeeping Mode, which you can enter by pressing C. You can seect either Japanese (kanji) or Engish for the day of the week indicator. For more information, see To set the current digita time and date manuay. Day of the Week Indicators Sunday: SU/ Monday: MO/ Tuesday: TU/ Wednesday: WE/ Thursday: TH/ Friday: FR/ Saturday: S/ Date Screen Day of week Day Or Day of week Reception date Last Signa Screen Press. Receiving Indicator and Seconds Count Receiving indicator Current Time Screen Seconds Hour : Minutes PM indicator Reception Time Setting the Digita Time and Date Manuay Make sure you seect your Home City code before you change the current time and date settings. Word Time Mode times are a dispayed in accordance with the Timekeeping Mode settings. Because of this, Word Time Mode times wi not be correct if you do not seect the proper Home City code before setting the time and date in the Timekeeping Mode. To set the current digita time and date manuay 1. In the Timekeeping Mode, hod down unti the transmitter indicator starts to fash, which indicates the The second hand wi move at high speed to the 12 o cock position, where it wi stop. 2. Use or C to move the fashing in the sequence shown beow to seect other settings. Transmitter indicator Press C. / Press. Transmitter/ City Settings Time/Date Settings Transmitter 12/24-Hour Format Power Saving C C City Code uto Receive 3. Use C to dispay the transmitter screen. The transmitter indicator that appears indicates whether the currenty seected Home City code is one that supports time caibration signa reception. This indicator: Means this: The currenty seected Home City code supports signa reception. DST Seconds Hour Minutes Language Day Month Year The currenty seected Home City code does not support signa reception. appears for the trasmitter whie NYC, CHI, DEN, LX, NC, or HNL is seected as the Home City. In this case, there is not need to seect a transmitter. You can change the transmitter when HKG, TYO, or SEL is seected as the Home City. For detais, see To configure the transmitter seection mode setting. 4. Use C and to seect the other time and date settings, and change the settings as described above. 5. When the setting you want to change is fashing, use B and/or D to change it as described beow. 4

5 Transmitter/City Settings Screen: See City Code Tabe for a compete ist of avaiabe city codes. Time/Date Settings Screen: Change the year Change the month or day Togge the day of the week anguage between Japanese (kanji) and Engish Togge Power Saving on (ON) and off (OF) Use D (+) and B ( ). Use D (+) and B ( ). Use D (+) and B ( ). For information about settings other than the time and date, see the foowing. Iumination duration: Iumination Power Saving: Power Saving Function 6. Use to exit the If a Transmitter/City Setting screen is dispayed, press twice. If a Time/Date Setting screen is dispayed, press once. The second hand wi advance at high speed to the correct position in accordance with the digita time seconds count, and resume norma movement from there. When you exit the setting screen, the anaog hands are adjusted automaticay to match the digita time. See naog Timekeeping for more information. uto DST () can be seected ony whie HNL, NC, LX, DEN, CHI, NYC, HKG, TYO, or SELis seected as the Home City code. For more information, see Dayight Saving Time (DST) beow. The auto receive setting is used for time caibration signa reception ony. See bout uto Receive for detais. Dayight Saving Time (DST) Dayight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not a countries or even oca areas use Dayight Saving Time. The time caibration signa transmitted from Fort Coins incudes both Standard Time and DST data. When the uto DST setting is turned on, the watch switches between Standard Time and DST (summer time) automaticay in accordance with the Fort Coins signa. The time caibration signas transmitted from Fukushima and Fukuoka/Saga do not incude summer time data. The defaut DST setting is uto DST () whenever you seect HNL, NC, LX, DEN, CHI, NYC, TYO, SEL, or HKG as your Home City code. If you experience probems receiving the time caibration signa in your area, it is probaby best to switch between Standard Time and Dayight Saving Time (summer time) manuay. To change the Dayight Saving Time (summer time) setting 1. In the Timekeeping Mode, hod down unti the transmitter indicator starts to fash, which indicates the 2. Press C twice and the DST setting screen appears. 3. Use D to cyce through the DST settings in the sequence shown beow. uto DST () DST off (OF) DST on (ON) 4. When the setting you want is seected, press twice to exit the The DST indicator appears on the dispay to indicate that Dayight Saving Time is turned on. naog Timekeeping The anaog time of this watch is synchronized with the digita time. The anaog time setting is adjusted automaticay whenever you change the digita time. The hands for the anaog timepiece move to adjust to a new setting whenever any of the foowing occurs. When you change the digita time setting manuay When the digita time setting is changed by time caibration signa reception When you change the Home City code and/or DST setting If the anaog time does not match the digita time for any reason, use the procedure described under To adjust the anaog time to match the anaog setting to the digita setting. Whenever you need to adjust both the digita and the anaog time settings manuay, make sure you adjust the digita setting first. Depending on how much the hands have to move in order to adjust to the digita time, it may take some time before they stop moving. To adjust the anaog time 1. In the Timekeeping Mode, press C five times to enter the Hand Setting Mode. 2. Hod down unti starts to fash, which indicates the The second hand wi move at high speed to the 12 o cock position, where it wi stop. 3. If the second hand is not pointing precisey at 12 o cock at this time, use D to adjust its position. Each press of D causes the second hand to advance by one second. To do this: Change the city code Cyce between Dayight Saving Time (ON), Standard Time (OF), and uto DST () Togge between auto receive on (ON) and off (OF) To do this: Togge between 12-hour ( ) and 24-hour ( ) timekeeping Reset the seconds to Togge the iumination duration setting between 1.5 second ( ) and 2.5 seconds ( ) Change the hour or minutes Do this: Use D (east) and B (west). Do this: Press B. 4. Press C. This wi cause the time on the digita dispay to fash, which indicates that adjustment of hour and minute hands is seected. 5. Use D and B to adjust the anaog setting as described beow. When you want to do this: Move the hand setting forward 20 seconds Move the hand setting back 20 seconds Move the hand setting a short way forward at high speed Move the hand setting a short way back at high speed Move the hand setting a ong way forward at high speed Move the hand setting a ong way back at high speed Hod down D. Reease D when the hands reach the setting you want. Hod down B. Reease B when the hands reach the setting you want. Whie hoding down D to move the hands at high-speed, press B to ock the high-speed hand movement. To stop the hand movement, press any button. Hand movement stops automaticay if the hour hand makes one fu (12-hour) revoution. Whie hoding down B to move the hands at high-speed, press D to ock the high-speed hand movement. To stop the hand movement, press any button. Hand movement stops automaticay if the hour hand makes one fu (12-hour) revoution. 6. Press to exit the The minute hand wi be adjusted sighty to match the seconds when you exit the To return to the Timekeeping Mode, press C. Reference This section contains more detaied and technica information about watch operation. It aso contains important precautions and notes about the various features and functions of this watch. Power Saving Function When turned on, the Power Saving function automaticay enters a seep state whenever the watch is eft in an area where ighting is dim (ess than about 30 ux). The foowing shows how watch functions are affected when eft in a dark pace whie in the seep state. Power Saving indicator pproximate Period Functions in seep state 3 to 4 days LCD off arm, houry time signa, anaog timekeeping and auto receive enabed 8 days or more LCD off, aarm and houry time signa disabed naog timekeeping stopped at 12 o cock uto receive disabed The seep state is indicated by a bank screen with the Power Saving indicator ( PS) fashing on it. Wearing the watch inside the seeve of cothing can cause it to enter the seep state. To recover from the seep state Perform any one of the foowing operations. Move the watch to a we-it area. Press any button. To turn Power Saving on and off 1. In the Timekeeping Mode, hod down unti the transmitter indicator starts to fash, which indicates the The second hand wi move at high speed to the 12 o cock position, where it wi stop. 2. Press again. 3. Press C eight times unti the Power Saving on/off On/Off status screen appears. 4. Press D to togge Power Saving on (ON) and off (OF). 5. Press to exit the The second hand wi advance at high speed to the correct position in accordance with the digita time seconds count, and resume norma movement from there. The Power Saving indicator (PS) is on the dispay in a modes whie the Power Saving is turned on. Perform this button operation: Press B. uto Return Features If you eave the watch in the arm or Hand Setting Mode, or with the Battery Leve Indicator (HI or MID) dispayed for two or three minutes without performing any operation, it automaticay returns to the Timekeeping Mode. If you eave the watch with a fashing setting on the dispay for two or three minutes without performing any operation, the watch automaticay exits the Scroing The B and D buttons are used in various modes and setting screens to scro through data on the dispay. In most cases, hoding down these buttons during a scro operation scros through the data at high speed. Initia Screens When you enter the Word Time or arm Mode, the data you were viewing when you ast exited the mode appears first. 5

6 City Code Tabe Radio-controed tomic Timekeeping Precautions Strong eectrostatic charge can resut in the wrong time being set. The time caibration signa bounces off the ionosphere. Because of this, such factors as changes in the refectivity of the ionosphere, as we as movement of the ionosphere to higher atitudes due to seasona atmospheric changes or the time of day may change the reception range of the signa and make reception temporariy impossibe. Even if the time caibration signa is received propery, certain conditions can cause the time setting to be off by up to one second. The current time setting in accordance with the time caibration signa takes priority over any time settings you make manuay. The watch is designed to automaticay update the date and day of the week for the period January 1, 2000 to December 31, Setting of the date by the time caibration signa cannot be performed starting from January 1, This watch can receive signas that differentiate between eap years and non-eap years. Though this watch is designed to receive both time data (hour, minutes, seconds) and date data (year, month, day), certain signa conditions can imit reception to time data ony. Normay, the signa reception date shown by the ast signa screen is the date data incuded in the received time caibration signa. When ony time data is received, however, the ast signa screen shows the date as kept in the Timekeeping Mode at the time of signa reception. If you are in an area where proper time caibration signa reception is impossibe, the watch keeps time within ±15 seconds a month at norma temperature. If you have probems with proper time caibration signa reception or if the time setting is wrong after signa reception, check your current city code, DST (summer time), and auto receive settings. The foowing are the initia factory defauts for these settings. Setting Initia Factory Defaut City code TYO (Tokyo) DST (summer time) (uto switching) uto receive (uto receive) Configuring Transmitter Seection Mode Settings that the transmitter seection mode setting can be configured ony when TYO, SEL, or HKG is seected as the Home City. See the map for more information. To configure the transmitter seection mode setting 1. In the Timekeeping Mode, hod down unti the transmitter indicator starts to fash, which indicates the The second hand wi move at high speed to the 12 o cock position, where it wi stop. 2. Use D to seect the transmitter you want to use. Each press of D cyces through the avaiabe settings as described beow. Transmitter indicator T : The watch automaticay seects the frequency that has the strongest signa. : Receives the signa from Fukushima (40kHz). : Receives the signa from Fukuoka/Saga (60kHz). 3. Press twice to exit the Reception can take up to 14 minutes when the T option is seected. The second hand wi advance at high speed to the correct position in accordance with seconds count of the digita time, and resume norma movement from there. City Code HNL NC LX DEN CHI NYC CCS* RIO GMT LON PR BER TH CI JRS JED THR DXB KBL KHI DEL DC RGN BKK HKG SEL TYO DL SYD NOU WLG City Honouu nchorage Los ngees Denver Chicago New York Caracas Rio De Janeiro London Paris Berin thens Cairo Jerusaem Jeddah Tehran Dubai Kabu Karachi Dehi Dhaka Yangon Bangkok Hong Kong Seou Tokyo deaide Sydney Noumea Weington GMT Differentia Other major cities in same time zone Pago Pago Papeete Nome San Francisco, Las Vegas, Vancouver, Seatte/Tacoma, Dawson City, Tijuana E Paso, Edmonton, Cuiacan Houston, Daas/Fort Worth, New Oreans, Mexico City, Winnipeg Montrea, Detroit, Miami, Boston, Panama City, Havana, Lima, Bogota La Paz, Santiago, Port Of Spain Sao Pauo, Buenos ires, Brasiia, Montevideo Praia Dubin, Lisbon, Casabanca, Dakar, bidjan Mian, Rome, Madrid, msterdam, giers, Hamburg, Frankfurt, Vienna, Stockhom Hesinki, Istanbu, Beirut, Damascus, Cape Town Kuwait, Riyadh, den, ddis baba, Nairobi, Moscow Shiraz bu Dhabi, Muscat Mae Mumbai, Kokata, Coombo Jakarta, Phnom Penh, Hanoi, Vientiane Singapore, Kuaa Lumpur, Beijing, Taipei, Mania, Perth, Uaanbaatar Pyongyang Darwin Mebourne, Guam, Rabau Port Via Christchurch, Nadi, Nauru Isand Based on data as of March The rues governing goba times (GMT differentia and UTC offset) and summer time are determined by each individua country. * In December 2007, Venezuea changed its offset from 4.0 to 4.5. however, that this watch dispays an offset of 4.0 (the od offset) for the CCS (Caracas, Venezuea) city code. Timekeeping Resetting the seconds to 00 whie the current count is in the range of 30 to 59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are reset to 00 without changing the minutes. The day of the week is automaticay dispayed in accordance with the date (year, month, and day) settings. The year can be set in the range of 2000 to The watch s buit-in fu automatic caendar makes aowances for different month engths and eap years. Once you set the date, there shoud be no reason to change it except after you have the watch s battery repaced or when battery eve drops to Leve 4. The current time for a city codes in the Timekeeping Mode and Word Time Mode is cacuated in accordance with the Greenwich Mean Time (GMT) differentia for each city, based on your Home City time setting. GMT differentia is cacuated by this watch based on Universa Time Coordinated (UTC*) data. * UTC is the word-wide scientific standard of timekeeping. It is based upon carefuy maintained atomic (cesium) cocks that keep time accuratey to within microseconds. Leap seconds are added or subtracted as necessary to keep UTC in sync with the Earth s rotation. The reference point for UTC is Greenwich, Engand. 12-hour/24-hour Timekeeping Formats The 12-hour/24-hour timekeeping format you seect in the Timekeeping Mode is aso appied in a other modes. With the 12-hour format, the P (PM) indicator appears on the dispay for times in the range of noon to 11:59 p.m. and no indicator appears for times in the range of midnight to 11:59 a.m. With the 24-hour format, times are dispayed in the range of 0:00 to 23:59 without any indicator. Iumination Precautions The iumination provided by the ight may be hard to see when viewed under direct sunight. Iumination automaticay turns off whenever an aarm sounds. Frequent use of iumination shortens the battery operating time. 6