General terms and conditions... F-7 Glossary of terms / General precautions... P.1455~ / P panasonic.net/id/pidsx/global

Transcription

1 9 Digita Sensor FX- SERIES Reated Information Genera terms and conditions... F-7 Gossary of terms / Genera precautions... P.455~ / P.5 Sensor seection guide... P.3~ seection... P.5~ PHOTO PHOTO IGHT FOW PARTICUAR Conforming to EMC Directive isting SIMPE MEASURE ITY * The FX- series has been changed to Panasonic brand from production in and after Juy 2. * Cover opened state is shown. panasonic.net/id/pidsx/goba PNP output type avaiabe Automatic sensitivity Timer Test input Interference prevention ight intensity monitor PC Taking fiber sensors to the next eve VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Good dua digita dispay The threshod vaue and incident ight intensity can be both confirmed at the same time, bringing good operabiity when making changes of each. Commerciay-avaiabe connectors reduce ead time and spare part numbers Compatibe with commerciay-avaiabe connectors, so that processing costs and ead time required for processing after purchase can be greaty reduced. The connection parts same as the DP- series digita pressure sensors and the PM-64 series micro photoeectric sensors can be commony used. Commerciay-avaiabe crimping connectors are used, so that the processing costs for connection cabes can be greaty reduced. Conventiona (cabe type) Purchase and preqaration of sensor Harness processing by outside order Sensor instaation From now on (buit-in connector type) Purchase and preqaration of sensor Harness processing by outside order Sensor instaation Using cabes with connectors Customer Harness processor Conventiona ead time Harness processing by outside order is needed after sensor preparation. Harness processing can be done by outside order at the same time of sensor preparation. No need junction connector. Customer Sensor preparation Sensor instaation Harness processor Sensor preparation ead time from now on Harness processing ead time further reduced Harness processing Sensor instaation Reduced Threshod vaue Incident ight intensity Purchase and preqaration of sensors and cabe with connectors Sensor instaation Harness processing by outside order is not needed. ead time and spare part numbers can be reduced. Customer Sensor preparation Sensor instaation Reduced Reduced ead time Ramco Nationa nsaes@ramcoi.com

2 Digita Sensor FX- SERIES 2 Saving-space with a width of 9 mm.354 in Very sim body at ony 9 mm.354 in. This is much thinner than existing fiber sensors. This makes a very arge difference when using many units, even if the difference of one unit is sma. Simpe operation due to cear configuration system Improved stabiity over ong terms Utiizes Four-chemica emitting eement for ight emission. The ight emission is guaranteed to be stabe over ong periods of time. [Stabe sensing comparison] FX- ight-emitting amount ong-term stabiity Three-chemica emitting eement Continued to use the configuration system of digita pressure sensor DP- series, which has received high popuarity since its reease. We have separated the s into three eves: RUN mode, SET mode, and PRO mode, making operation simper and easier. Functions used during norma operation RUN mode Changing threshod vaues Key ock Quick s Code s Simpe Specia and detaied Incident ight intensity Threshod vaue 9 mm.354 in Time Functions used when initiaizing the sensor and carrying out maintenance SET mode Teaching -ON / D-ON Timer Emission amount Emission frequency Equipped with a fu compement of digita fiber sensor functions PRO mode Shift Reset ECO Threshod vaue margin Threshod vaue foow-up cyce Externa input GETA Inverting dispay Copy PHOTO PHOTO IGHT FOW PARTICUAR SIMPE MEASURE ITY PC VISUAIZATION Quick code input function Simpy imputing the defaut code (number) wi enabe sensor s. Even if the s are accidentay changed, imputing the code wi restore the defaut s. Confirmation can be carried out smoothy via teephone by simpy quoting numbers. This can be of great assistance when deaing with foreign country customers. Quick : Press and simutaneousy for 2 sec. Code : Press and simutaneousy for 4 sec. RUN mode Quick numbers (abstract) No Output Timer Emission amount operation Dark-ON Dark-ON Dark-ON Dark-ON ight-on ight-on ight-on ight-on None None OFF-deay ms OFF-deay ms ON-deay 4 ms ON-deay 4 ms ON-deay ms ON-deay ms OFF ON OFF ON ON OFF ON OFF Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Refer to Quick function and Code function in PRECAUTIONS FOR PROPER for detais. Ramco Nationa nsaes@ramcoi.com

3 2 Digita Sensor FX- SERIES PHOTO PHOTO IGHT FOW PARTICUAR SIMPE MEASURE ITY PC VISUAIZATION Teaching with ON / OFF keys SET mode Simpy press the ON key when an object is present, and OFF when it is not, and teaching is competed. There is no need to consider difference between ight-on and Dark-ON. <Setting exampe> Thru-beam type / Retrorefective type Refective type Object present ON Object present ON Object absent OFF Object absent OFF Teaching even without an object imit teaching function Threshod vaue can be set by performing teaching ony when an object is absent (when the incident ight amount is stabe). This is usefu when there are other objects in the background aso when defecting a minute objects. Teaching can aso be carried out using externa input. Resoves variation in incident ight intensity dispay GETA function PRO mode Even when performing the same sensing operation, there may be variances in the digita vaues of the fiber amp. There is no probem with the sensor itsef, but the operator may find it troubing. Given vaue can be corrected with the GETA function, so the apparent variation can be eiminated and the creation of operation manuas can proceed smoothy. Variations in the amount of ight received Unify at 5 using the GETA function Exampe of current incident ight intensity dispay of adjusted to 4, [digits] Incident ight intensity 5 current vaue 4, [digits], 5 Not dispayed is Because the origina vaue is 5, sensor dispays 5 for the ower imit vaue and 4, for the upper imit vaue. Threshod vaue foow-up cyce function PRO mode Emission amount function SET mode Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F This function performs automatic to threshod vaue by checking the incident ight intensity at desired intervas in order to foow the changes in the ight amount resuting from changes in the environment over ong periods (such as dust). Contributes to reduction in maintenance hours. * Effective when the output operation is set to Dark-ON, and when using thru-beam type or retrorefective type fibers. Incident ight intensity Threshod vaue Current vaue Incident ight intensity when an object is absent. Time Emission amount can be reduced in order to achieve stabe detection when the receiving ight eve is saturated, such as detection at cose range and detection of transparent or minute objects. Previousy, the emission amount eve was ony one, but from production in December 27, four eve (three eve + auto ) has become avaiabe. This function brings easier s than before. [ight receiving eve saturated] Actua digit difference: C A Upper dispay imit 4 B Incident ight intensity Saturated digit difference: D ight emitting amount decreased Incident ight intensity A, B, [Stabe sensing] Actua digit difference: C Ramco Nationa nsaes@ramcoi.com

4 Digita Sensor FX- SERIES 22 Emission frequency mode SET mode Mutua interference is prevented for max. 3 units for standard type FX- and max. 4 units in case of ong sensing range type FX-2. During of interference prevention, emitter and output indicator both fash, so it is convenient to confirm which fiber is in the process at a gance. Emitter fashes even when an ampifier is not instaed cose together. * When the emission frequency is changed, a response time is aso changed. Aert function The emitter and output indicator fash at the same frequency. Externa input mode PRO mode When the amount ight received approaches the threshod vaue, the dispay can be made to bink in order to aert the operator. <When using at a shift amount of 2% and a threshod vaue of,> The amount of ight received ranges from about 9 to, when the digita indicator fashes. Incident ight intensity, approx. 9 approx. Range of the digita indicator fashing (margin: sma) PRO mode Externa input can be seected from emission hat, imit teaching / fu-auto teaching / 2-eve teaching, ECO or emission amount test. Threshod vaue set at each teaching is aso memorized. * 2-eve teaching, emission amount test and threshod vaue storing are avaiabe in ampifiers manufactured after December 27. (Brown) +V (Back) Output () Externa input (Bue) V Externa input ines are equipped as standard Digita dispay inversion Coor of ead wire of attached connector cabe PC etc. Threshod vaue of, PRO mode The viewing orientation of the digita dispay can be inverted in accordance with the direction of the ampifier. Previous products (without inversion function) FX- SERIES Turn OFF Turn ON Setting copy function to reduce man-hours and human error PRO mode By connecting a fiber sensor to the master fiber sensor, the master sensor s can be copied aong with data communications. When the same s are input to severa units, troube from errors can be prevented, aso changes to the work order wi be sma when equipment design is changed. <Wiring to copy s> Coor of ead wire of attached connector cabe Master side (Brown) +V (Back) Output () Externa input (Bue) V Save side (Brown) +V (Back) Output () Externa input (Bue) V + 2 to 24 V DC ± % These s can be copied Threshod vaue, output operation, timer operation, timer emission amount, shift, externa input, threshod vauestoring, ECO inverting digita dispay, and threshod vaue margin Without mounting bracket Seectabe either mounting on DIN rai or direct mounting with through hoe. Direct mounting brings stabiity even on a movabe parts or instaation of a singe unit. Avaiabe from standard type or ong sensing range type Standard type and ong sensing range type are avaiabe which has various response time and sensing range. The mode best meet appication needs can be seected. Mode No. Type Sensing range (FT-43) Response time FX- Standard type 35 mm 3.78 in Max. 25 μs FX-2 ong sensing range type 97 mm in Max. 2.5 ms Power consumption saving with ECO mode ø3.2 mm.26 in mounting hoes Can be mounted with M3 screws. ECO When there is no key operations in approximatey 2 seconds, digita dispay turns off and power consumption can be reduced to 6mW or ess (72mW in norma mode). PHOTO PHOTO IGHT FOW PARTICUAR SIMPE MEASURE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F The digita indicator fashes. Ramco Nationa nsaes@ramcoi.com

5 23 Digita Sensor FX- SERIES IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Ampifiers Standard type ong sensing range type ORDER GUIDE Type Appearance Mode No. M8 pug-in connector type M8 pug-in connector type Cabe set (Note ) M8 pug-in connector type M8 pug-in connector type Cabe set (Note ) FX- (Note 2) FX--Z (Note 3) FX-P (Note 2) FX-P-Z (Note 3) FX--CC2 FX-P-CC2 FX-2 (Note 2) FX-2-Z (Note 3) FX-2P (Note 2) FX-2P-Z (Note 3) FX-2-CC2 FX-2P-CC2 Emitting eement Red ED Output NPN open-coector NPN open-coector PNP open-coector PNP open-coector NPN open-coector PNP open-coector coector NPN open-coector NPN open-coector PNP open-coector PNP open-coector NPN open-coector PNP open-coector Accessory CN-4A-C2 Connector attached cabe * Ony incude cabe set type Notes: ) The connector attached cabe CN-4A-C2 is suppied with the ampifier. 2) Make sure to use the optiona connector attached cabe CN-4A(-R)-C or the connector CN-4A, or a connector manufactured by J.S.T. Mfg. Co., td. (contact: SPHD-T-P.5, housing: PAP-4V-S) 3) Make sure to use the optiona M8 connector attached cabe CN-24A-C. Designation Mode No. Description CN-4A-C m 3.28 ft Connector attached cabe CN-4A-C2 (Note) CN-4A-C3 3 m ft CN-4A-C5 5 m 6.44 ft CN-4A-R-C m 3.28 ft Connector CN-4A-R-C2 attached cabe (Fexibe type) CN-4A-R-C3 3 m ft CN-4A-R-C5 5 m 6.44 ft M8 connector CN-24A-C2 For M8 pug-in connector type attached cabe CN-24A-C5 5 m 6.44 ft Connector CN-4A Set of housings and 4 contacts Ampifier MS-DIN-4 mounting bracket MS-DIN-E End pates Two pcs. per set Mounting bracket for ampifier.2 mm 2 4-core cabtyre cabe with connector on one end Cabe outer diameter: ø3.7 mm ø.46 in The connector on one end Cabe outer diameter: ø4 mm ø.57 in When it moves depending on the way it is instaed on a DIN rai, these end pates ensure that a ampifiers are mounted together in a secure and fuy connected manner. Note: The connector attached cabe CN-4A-C2 is suppied with the cabe set type FX- -CC2. Recommended connector Contact: SPHD-T-P.5, Housing: PAP-4V-S (Manufactured by J.S.T. Mfg. Co., td.) Note: Contact the manufacturer for detais of the recommended products. Recommended crimping too Mode No.: YC-6R (Manufactured by J.S.T. Mfg. Co., td.) Note: Contact the manufacturer for detais of the recommended products. FC-FX- (Protection cover) * It have been attached from the production at Juy, 2. M8 connector attached cabe CN-24A-C ø9 ø.354 Ampifier mounting bracket MS-DIN-4 Connector attached cabe CN-4A(-R)-C Connector CN-4A ø4 ø.57 M8 connector attached cabe CN-24A-C Fixing ring Contact Housing Ramco Nationa nsaes@ramcoi.com

6 Digita Sensor FX- SERIES 24 IST OF S Thru-beam type (one pair set) s are isted in aphabetic order. Refer to p.5~ Seection for detais of each fiber. Mode No. Sensing range (mm in) (Note ) Standard type FX- ong sensing range type FX-2 FT-4 4, , (Note 2) FT FT FT-3S FT-3W FT FT FT-42S FT-42W FT FT-45X Type / Ambient temperature Threaded, M4, ong sensing range, 4 to +7 C 4 to 58 F Super quaity, Threaded, M3, 55 to +8 C 67 to 76 F Threaded, M3, 55 to +8 C 67 to 76 F Seeve, Threaded, M3, 55 to +8 C 67 to 76 F Threaded, M3, 4 to +6 C 4 to 4 F Super quaity, Threaded, M4, 55 to +8 C 67 to 76 F Threaded, M4, 55 to +8 C 67 to 76 F Seeve, Threaded, M4, 55 to +8 C 67 to 76 F Threaded, M4, 4 to +6 C 4 to 4 F Threaded, M4, 55 to +8 C 67 to 76 F Threaded, M4, 55 to +8 C 67 to 76 F FT-A, , (Note 2) Wide beam, 4 to +7 C 4 to 58 F cabe ength : Free-cut Dimensions m ft P.5 P.5 P.5 P.5 P.5 P.5 P.5 P.5 P.5 P.5 m 3.28 ft P.52 FT-AW, , Wide beam, 4 to +55 C 4 to 3 F P.52 FT-A32 3, (Note 2) 3, (Note 2) Wide beam, 4 to +6 C 4 to 4 F P.52 FT-A32W 3, (Note 2) 3, (Note 2) Wide beam, 4 to +55 C 4 to 3 F P.52 FT-A Wide beam, 55 to +8 C 67 to 76 F P.52 FT-E FT-E FT-H3-FM FT-H2-J2-S (Note 3) FT-H2-J3-S (Note 3) Cyindrica, Utra-sma dia., ø3.8, 4 to +7 C 4 to 58 F Cyindrica, Utra-sma dia., ø3.8, 4 to +7 C 4 to 58 F Heat-resistant, 6 to +3 C 76 to 266 F Heat-resistant (joint), 6 to +2 C 76 to 392 F Heat-resistant (joint), 6 to +2 C 76 to 392 F m 3.28 ft P.52 P.52 P.52 P.52 2 mm in (Note 4) P.53 3 mm.8 in (Note 4) P.53 IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION FT-H2-J5-S (Note 3) Heat-resistant (joint), 6 to +2 C 76 to 392 F 5 mm in (Note 4) P.53 FT-H2-M Heat-resistant, 6 to +2 C 76 to 392 F m 3.28 ft P.53 FT-H2-VJ5-S (Note 3) FT-H2-VJ8-S (Note 3) Heat-resistant (joint), 6 to +2 C 76 to 392 F Heat-resistant (joint), 6 to +2 C 76 to 392 F 5 mm in (Note 4) P.53 8 mm in (Note 4) P.53 Seection s Ampifiers FT-H2W-M 3.8 FT-H3-MV-S (Note 5) FT-H35-M FT-H35-M2S FT-H8Y , Heat-resistant, 6 to +2 C 76 to 392 F Vacuum-resistant, 3 to +3 C 22 to 572 F Heat-resistant, 6 to +35 C 76 to 572 F Heat-resistant, 6 to +35 C 76 to 572 F Chemica-resistant, Meta-free, 4 to +5 C 76 to 239 F Notes: ) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) The fiber cabe ength practicay imits the sensing range. 3) Heat-resistant joint fibers and ordinary-temperature fibers (FT-42) are sod as a set. 4) This is the fiber ength (fixed ength) for heat-resistant fibers. The ordinary-temperature fibers are free-cut to. 5) Sod as a set comprising vacuum type fiber + photo-termina (FV-BR) + fiber at atmospheric side (FT-J8). 6) The aowabe cutting range is 5 mm in from the end that the ampifier inserted. m 3.28 ft P.53 P.53 P.53 P.53 (Note 6) P.53 FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Ramco Nationa nsaes@ramcoi.com

7 25 Digita Sensor FX- SERIES IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F IST OF S Thru-beam type (one pair set) s are isted in aphabetic order. Refer to p.5~ Seection for detais of each fiber. Mode No. Sensing range (mm in) (Note ) Standard type FX- ong sensing range type FX-2 Type / Ambient temperature FT-KS4 2, , (Note 2) Narrow Beam, 4 to +6 C 4 to 4 F FT-KV FT-KV4 2, , (Note 2) FT-KV4W 2, , (Note 2) FT-8Y, , Narrow Beam, Side-view, 4 to +6 C 4 to 4 F Narrow Beam, Side-view, 4 to +6 C 4 to 4 F Narrow Beam, Side-view, 4 to +6 C 4 to 4 F Chemica-resistant, Meta-free, 4 to +7 C 4 to 58 F FT-R Square, M3, 55 to +8 C 67 to 76 F Notes: ) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) The fiber cabe ength practicay imits the sensing range. 3) The aowabe cutting range is 5 mm in from the end that the ampifier inserted. cabe ength : Free-cut Dimensions P.54 P.54 P.54 P.54 (Note 3) P.54 FT-R Threaded, M4, Ebow, 55 to +8 C 67 to 76 F P.54 FT-R4W Square, M4, 4 to +6 C 4 to 4 F P.54 FT-R42W , Square, M4, 4 to +6 C 4 to 4 F P.54 FT-R Square, M4, 55 to +8 C 67 to 76 F P.54 FT-R44Y FT-R6Y , Oi-resistant, Square, M4, Cabe-protection type, 55 to +8 C 67 to 76 F Oi-resistant, Square, M6, Fu-protection type, 55 to +8 C 67 to 76 F FT-S Cyindrica,.39, 55 to +8 C 67 to 76 F 5 mm in P.55 FT-S Super quaity, Cyindrica,.5.59, 55 to +8 C 67 to 76 F P.54 P.55 P.55 P.55 FT-S Cyindrica,.5.59, 55 to +8 C 67 to 76 F P.55 FT-S2W Cyindrica,.5.59, 4 to +6 C 4 to 4 F P.55 FT-S Super quaity, Cyindrica, 3.8, 55 to +8 C 67 to 76 F FT-S3W Cyindrica, 3.8, 4 to +6 C 4 to 4 F P.55 FT-S32, , 8. Cyindrica, , 4 to +7 C 4 to 58 F P.55 FT-V FT-V24W FT-V FT-V FT-V4, , FT-V8Y Seeve, Cyindrica, Side-view, 2.79, 55 to +8 C 67 to 76 F Seeve, Cyindrica, Side-view, 2.79, 4 to +6 C 4 to 4 F Seeve, Cyindrica, Side-view, 2.79, 55 to +8 C 67 to 76 F Seeve, Cyindrica, Side-view, , 55 to +8 C 67 to 76 F Cyindrica, Side-view, 4.57, 4 to +6 C 4 to 4 F Chemica-resistant, Meta-free 4 to +7 C 4 to 58 F P.55 P.55 P.56 P.56 P.56 P.56 (Note 3) P.56 FT-Z2HBW Fat with boss, 4 to +6 C 4 to 4 F P.56 m 3.28 ft FT-Z2W Fat with boss, 4 to +6 C 4 to 4 F P.56 FT-Z , Fat, 4 to +6 C 4 to 4 F FT-Z3E, , Fat, 4 to +6 C 4 to 4 F P.56 FT-Z3EW, , Fat, 4 to +6 C 4 to 4 F P.57 FT-Z3H, , Fat, 4 to +6 C 4 to 4 F P.57 FT-Z3HW, , Fat, 4 to +6 C 4 to 4 F P.57 FT-Z3W , Fat, 4 to +6 C 4 to 4 F P.57 FT-Z4HBW Fat with boss, 4 to +6 C 4 to 4 F P.57 FT-Z4W , Fat with boss, 4 to +6 C 4 to 4 F P.57 FT-Z82Y , Chemica-resistant, to +6 C 32 to 4 F P.57 P.56 Ramco Nationa nsaes@ramcoi.com

8 Digita Sensor FX- SERIES 26 IST OF S Retrorefective type s are isted in aphabetic order. Refer to p.5~ Seection for detais of each fiber. Mode No. Sensing range (mm in) (Note ) (Note 2) Standard type FX- ong sensing range type FX-2 Type / Ambient temperature FR-KZ22E 5 to 2.59 to 5 to to 4.73 Wafer mapping, 4 to +6 C 4 to 4 F cabe ength : Free-cut Dimensions FR-KZ5E 2 to to 2 to to 3.78 Narrow Beam, Side sensing, 4 to +6 C 4 to 4 F P.58 FR-KZ5H 2 to to 2 to to 3.78 Narrow Beam, Top sensing, 4 to +6 C 4 to 4 F P.58 FR-Z5HW to 55 to to 83 to With poarizing fiter, 25 to +55 C 3 to 3 F P.58 Notes: ) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. The sensing range of FR-KZ22E is specified for the attached refector. The sensing range of FR-KZ5E and FR-KZ5H is specified for the attached refector RF-3. The sensing range of FR-Z5HW is specified for the RF-3. 2) The sensing range is the possibe range for the attached refector. The fiber can detect an object ess than range for the refector. However, note that if there are any white or highy-refective surfaces near the fiber, refected incident ight may affect the fiber. If this occurs, adjust the threshod vaue of the ampifier unit before use. Refective type s are isted in aphabetic order. Refer to p.5~ Seection for detais of each fiber. Mode No. Sensing range (mm in) (Note ) (Note 2) / Description Standard type FX- ong sensing range type FX-2 Type / Ambient temperature Notes: ) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) The sensing range is specified for white non-gossy. 3) The aowabe cutting range is 5 mm in from the end that the ampifier inserted. cabe ength : Free-cut P.58 Dimensions FD Super quaity, Threaded, M3, 55 to +8 C 67 to 76 F P.59 FD Threaded, M3, 55 to +8 C 67 to 76 F P.59 FD-3W Threaded, M3, 4 to +6 C 4 to 4 F P.59 FD-32G Threaded, M3, 55 to +8 C 67 to 76 F P.59 FD-32GX Threaded, M3, 55 to +8 C 67 to 76 F m 3.28 ft (Note 3) P.59 FD Super quaity, Threaded, M4, 55 to +8 C 67 to 76 F P.59 FD Threaded, M4, 55 to +8 C 67 to 76 F P.59 FD-4S Seeve, Threaded, M4, 55 to +8 C 67 to 76 F P.59 FD-4SW Seeve, Threaded, M4, 4 to +6 C 4 to 4 F P.59 FD-4W Threaded, M4, 4 to +6 C 4 to 4 F P.59 FD-42G Threaded, M4, 55 to +8 C 67 to 76 F P.6 FD-42GW Threaded, M4, 4 to +6 C 4 to 4 F P.6 FD Super quaity, Threaded, M6, 55 to +8 C 67 to 76 F P.6 FD Threaded, M6, 55 to +8 C 67 to 76 F P.6 FD-6G Threaded, M6, 55 to +8 C 67 to 76 F P.6 FD-6S Seeve, Threaded, M6, 55 to +8 C 67 to 76 F P.6 FD-6W Threaded, M6, 4 to +6 C 4 to 4 F P.6 FD Threaded, M6, 55 to +8 C 67 to 76 F P.6 FD-64X Threaded, M6, 55 to +8 C 67 to 76 F m 3.28 ft P.6 FD-A Wide beam, 4 to +6 C 4 to 4 F P.6 FD-A Array, 55 to +8 C 67 to 76 F P.6 FD-E Cyindrica, Utra-sma dia., ø.5.59, 4 to +6 C 4 to 4 F P.6 m 3.28 ft FD-E Cyindrica, Utra-sma dia., ø3.8, 4 to +7 C 4 to 58 F P.6 FD-EG Threaded, M3, Utra-sma dia., 4 to +7 C 4 to 58 F 5 mm in P.6 FD-EG3S Seeve, Threaded, Utra-sma dia., M3, 4 to +7 C 4 to 58 F m 3.28 ft P.62 FD-EG Threaded, M3, Utra-sma dia., 2 to +6 C 4 to 4 F 5 mm in P.62 FD-F4 FD-F4 Appicabe pipe diameter: Outer dia. ø6 to ø26 mm ø.236 to ø.24 in transparent pipe [P (fuorine resin) or equivaenty transparent pipe, wa thickness mm.39 in] iquid absent: Beam received, iquid present: Beam interrupted Appicabe pipe diameter: Outer dia. ø6 to ø26 mm ø.236 to ø.24 in transparent pipe [PVC (viny choride), fuorine resin, poycarbonate, acryic, gass, wa thickness to 3 mm.39 to.8 in] iquid absent: Beam received, iquid present: Beam interrupted Pipe-mountabe type, iquid eve sensing, 4 to + C 4 to 22 F Pipe-mountabe type, iquid eve sensing, 4 to + C 4 to 22 F Ramco Nationa nsaes@ramcoi.com P.62 P.62 IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F

9 27 Digita Sensor FX- SERIES IST OF S IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Refective type s are isted in aphabetic order. Refer to p.5~ Seection for detais of each fiber. Mode No. FD-F4Y (Note 3) FD-F8Y FD-93 Sensing range (mm in) (Note ) (Note 2) / Description Standard type FX- ong sensing range type FX-2 ø4 mm ø.57 in Protective tube: Fuorine resin, ength 5 mm in (cuttabe) iquid surface not contacted: Beam received, iquid surface contacted: Beam interrupted ø6 mm ø.236 in Protective tube: Fuorine resin, ength, mm in (not cuttabe) iquid surface not contacted: Beam received, iquid surface contacted: Beam interrupted Appicabe pipe diameter: Outer dia. ø8 mm ø.35 in or more transparent pipe (When used with the tying bands: ø8 to ø8 mm ø.35 to ø3.5 in) [P (fuorine resin), incuding transucent] iquid absent: Beam received, iquid present: Beam interrupted Type / Ambient temperature Contact type, iquid eve sensing, Meta-free, 4 to +7 C 4 to 58 F Contact type, iquid eve sensing, 4 to +25 C 4 to 257 F Pipe-mountabe type, iquid sensing, 4 to +7 C 4 to 58 F cabe ength : Free-cut Dimensions P.62 (Note 6) P.62 FD-H3-FM Heat-resistant, Threaded, 6 to +3 C 76 to 266 F P.63 FD-H8-3 to to.394 to 25 to.984 Heat-resistant, Gass substrate detection convergent refective, 6 to +8 C 76 to 356 F FD-H Heat-resistant, Threaded, 6 to +2 C 76 to 392 F P.63 m 3.28 ft FD-H2-M Heat-resistant, Threaded, 6 to +2 C 76 to 392 F P.63 FD-H25-43 (Note 4) 4 to 6.57 to.63 4 to to.96 Heat-resistant, Gass substrate detection convergent refective, 2 to +25 C 4 to 482 F (Ordinary temp. side:-2 to +7 C 4 to 58 F) P.63 3 m ft FD-H25-45 (Note 4) 7 to to to to.496 Heat-resistant, Gass substrate detection convergent refective, 2 to +25 C 4 to 482 F (Ordinary temp. side:-2 to +7 C 4 to 58 F) P.63 FD-H3-KZV-S (Note 4, 5) 25 to to 3.5 to to 8.66 FD-H to 9.79 to.354 to 7 to.669 FD-H3-32V-S (Note 4, 5) 2.5 to to.256 to to.433 Vacuum-resistant, Refective, 3 to +3 C 22 to 572 F Heat-resistant, Gass substrate detection convergent refective, 6 to +3 C 76 to 572 F Vacuum-resistant, Convergent refective, 3 to +3 C 22 to 572 F P.62 P.63 m 3.28 ft P.64 P.64 3 m ft P.64 FD-H35-2S Heat-resistant, Threaded, 6 to +35 C 76 to 662 F m 3.28 ft P.64 FD-H35-M Heat-resistant, Threaded, 6 to +35 C 76 to 662 F P.64 FD-H35-M2S Heat-resistant, Threaded, 6 to +35 C 76 to 662 F P.64 FD-HF4Y (Note 3) ø4 mm ø.57 in Protective tube: Fuorine resin, ength 5 mm in (cuttabe) iquid surface not contacted: Beam received, iquid surface contacted: Beam not received Contact type, iquid eve sensing, Meta-free, 4 to +5 C 4 to 22 F FD- (Note 4) to 4.5 to.77 to 5.5 to.27 Gass substrate detection, 4 to +6 C 4 to 4 F P.65 FD- (Note 4) to 8 to.35 to 9 to.354 Gass substrate detection, 4 to +6 C 4 to 4 F P.65 FD-2W (Note 4) to to.77.5 to 7.2 to.276 Uta-sma, 4 to +6 C 4 to 4 F m 3.28 ft P.65 FD-2H 5 to 5.97 to.59 to 3.39 to.8 Genera purpose, 4 to +7 C 4 to 58 F FD-2 (Note 4) 3 to 5.8 to.59.5 to 6.59 to.63 Gass substrate detection, 4 to +6 C 4 to 4 F P.65 FD-2W (Note 4) 7 to to to 4.8 to.55 Gass substrate detection, 4 to +6 C 4 to 4 F P.65 FD-22A (Note 4) to 9 to.748 to 25 to.984 Gass substrate detection, to +7 C 32 to 58 F P.65 FD-23 (Note 4) to 28 to.2 to 3 to.8 Gass substrate detection, 2 to +7 C 4 to 58 F FD-3A (Note 4) to 4 to.575 to 5 to Gass substrate detection, to +7 C 32 to 58 F 3 m ft P.65 FD-3A (Note 4) 5 to 3.97 to.8 4 to to.299 Gass substrate detection, to +7 C 32 to 58 F P.65 FD-32H (Note 4) 6 to 3.63 to.8 to 5 to Gass substrate detection, 4 to +6 C 4 to 4 F 4 m 3.23 ft P.66 Notes: ) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) The sensing range of refective type is the vaue for white non-gossy (as for FD-H3-32 and FD-H mm in gass substrate). 3) iquid infow prevention joint, protective tube extension joint, fiber mounting joint are avaiabe. Pease refer to p.38 for detais. 4) The sensing range is specified for transparent gass t.7 mm t.28 in (FD-32H: R edge, FD-2 and FD-2W: t2 mm t.79 in) [FD-: siicon wafers mm in]. 5) Sod as a set comprising vacuum type fiber + photo-termina (FV-BR) + fiber at atmospheric side (FT-J8). 6) The aowabe cutting range is, mm in from the end that is inserted to the ampifier. P.64 P.65 P.65 Ramco Nationa nsaes@ramcoi.com

10 Digita Sensor FX- SERIES 28 IST OF S Refective type s are isted in aphabetic order. Refer to p.5~ Seection for detais of each fiber. Mode No. Sensing range (mm in) (Note ) (Note 2) Standard type FX- ong sensing range type FX-2 Type / Ambient temperature cabe ength : Free-cut FD-R3G Square, M3, 55 to +8 C 67 to 76 F P.66 FD-R32EG Square, M3, 4 to +7 C 4 to 58 F FD-R33EG Square, M3, 2 to +6 C 4 to 4 F 5 mm in P.66 FD-R34EG Square, M3, 4 to +7 C 4 to 58 F P.66 FD-R Square, M4, 55 to +8 C 67 to 76 F FD-R Threaded, M6, Ebow, 55 to +8 C 67 to 76 F P.66 FD-R6Y Oi-resistant, Square, M6, Cabe-proection type, 55 to +8 C 67 to 76 F P.66 FD-S Cyindrica, ø.5.59, 55 to +8 C 67 to 76 F m 3.28 ft P.66 FD-S Super quaity, Cyindrica, ø3.8, 55 to +8 C 67 to 76 F FD-S Cyindrica, ø3.8, 55 to +8 C 67 to 76 F Dimensions P.66 P.66 P.67 FD-S Cyindrica, ø3.8, 55 to +8 C 67 to 76 F P.67 FD-S32W Cyindrica, ø3.8, 4 to +6 C 4 to 4 F P.67 FD-S33GW Cyindrica, ø3.8, 4 to +6 C 4 to 4 F P.67 FD-S6Y FD-V FD-V3W FD-V Chemica-resistant, Chindrica, Meta-free, ø5.5.27, 4 to +7 C 4 to 58 F Seeve, Cyindrica, Side-view, ø3.8, 55 to +8 C 67 to 76 F Seeve, Cyindrica, Side-view, ø3.8, 4 to +6 C 4 to 4 F Seeve, Cyindrica, Side-view, ø5.97, 55 to +8 C 67 to 76 F P.67 (Note 3) P.67 FD-Z2HBW 2 to 3.79 to.8 to 9.39 to Fat with boss, 4 to +6 C 4 to 4 F P.68 m 3.28 ft FD-Z2W 2 to to.26 to 8.39 to 3.5 Fat with boss, 4 to +6 C 4 to 4 F P.68 FD-Z4HBW to 9.39 to to 24.2 to Fat with boss, 4 to +6 C 4 to 4 F FD-Z4W to to Fat with boss, 4 to +6 C 4 to 4 F P.68 FD-Z5HW to to to to Narrow Beam, ong range, 4 to +6 C 4 to 4 F P.68 Notes: ) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) The sensing range is specified for white non-gossy. 3) The aowabe cutting range is 5 mm in from the end that the ampifier inserted. P.67 P.67 P.68 P.68 IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Sensing range when FR-Z5HW is used in combination with a refector (optiona) Refector Mode No. Standard type FX- Sensing range (mm in) ong sensing range type FX-2 RF-23 to 2,4 to to 5, to RF-22 to,3 to 5.8 to 2,6 to RF-2 to 98 to to,3 to 5.8 Note: The sensing range is the possibe range for the refector. The fiber can detect an object ess than mm in. However, note that if there are any white or highy-refective surfaces near the fiber, refected incident ight may affect the fiber. If this occurs, adjust the threshod vaue of the ampifier unit before use. Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Ramco Nationa nsaes@ramcoi.com

11 29 Digita Sensor FX- SERIES Refer to p.69~ for detais of ens dimensions. ens (For thru-beam type fiber) IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Designation Mode No. Description Sensing range (mm in) [ens on both sides] Mode FX- FX-2 FT-43 2, , (Note 2) Expansion ens (Note ) Superexpansion ens (Note ) Side-view ens Expansion ens for vacuum fiber (Note ) Vacuumresistant side-view ens (Note ) FX-E FX-E2 FX-SV FV-E FV-SV2 Increases the sensing range by 5 times or more. Ambient temperature: 6 to +35 C 76 to +662 F (Note 4) Beam dia: ø3.6 mm ø.42 in Tremendousy increases the sensing range with arge diameter enses. Ambient temperature: 6 to +35 C 76 to +662 F (Note 4) Beam dia: ø9.8 mm ø.386 in Beam axis is bent by 9. Ambient temperature: 6 to +3 C 76 to +572 F (Note 4) Beam dia: ø2.8 mm ø. in Sensing range increases by 4 times or more. Ambient temperature: 6 to +35 C 76 to +662 F (Note 4) Beam dia: ø3.6 mm ø.42 in Beam axis is bent by 9. Ambient temperature: 6 to +3 C 76 to +572 F (Note 4) Beam dia: ø3.7 mm ø.46 in FT-42 FT-42W 3, , (Note 2) FT-45X, (Note 2), (Note 2) FT-R4 3, , (Note 2) FT-R43, , (Note 2) FT-H35-M2 2, , (Note 2) FT-H2W-M,3 5.8, (Note 2) FT-H2-M, (Note 2), (Note 2) FT-H2-J5-S FT-H2-J3-S FT-H2-J2-S, , (Note 2) Sensing range (mm in) [ens on both sides] Mode FX- FX-2 FT-43 FT-42 3, (Note 2) 3, (Note 2) FT-42W FT-45X, (Note 2), (Note 2) FT-R4 3, (Note 2) 3, (Note 2) FT-R43 3, (Note 2) 3, (Note 2) FT-H35-M2 3, (Note 2) 3, (Note 2) FT-H2W-M FT-H2-M, (Note 2), (Note 2) FT-H3-FM2 3, (Note 2) 3, (Note 2) FT-H2-J5-S FT-H2-J3-S FT-H2-J2-S 3, (Note 2) 3, (Note 2) Sensing range (mm in) [ens on both sides] Mode FX- FX-2 FT , FT , FT-42W ,3 5.8 FT-45X , (Note 2) FT-R FT-H35-M FT-H2W-M FT-H2-M FT-H2-J5-S FT-H2-J3-S FT-H2-J2-S Sensing range (mm in) [ens on both sides] (Note 3) Mode FX- FX-2 FT-H3-MV-S , Sensing range (mm in) [ens on both sides] (Note 3) Mode FX- FX-2 FT-H3-MV-S , Notes: ) Be carefu sure to use it ony after you have adjusted it sufficienty when instaing the thru-beam type fiber equipped with the expansion ens, as the beam enveope becomes narrow and aignment is difficut. 2) The fiber cabe ength practicay imits the sensing range. 3) The fiber cabe ength for the FT-H3-MV-S is m 3.28 ft. The sensing ranges in FX-2 are specified considering the ength of the FT-J8 atmospheric side fiber. 4) Refer to IST OF S (p.24~) for the ambient temperature of fibers to be used in combination. Ramco Nationa nsaes@ramcoi.com

12 Digita Sensor FX- SERIES 3 Refer to p.69~ for detais of ens dimensions. ens (For refective type fiber) Designation Mode No. Description Pinpoint spot of ø.5 mm ø.2 in. Enabes detection of minute objects or sma marks. Pinpoint FX-MR Distance to foca point: 6 ± mm.236 ±.39 in Appicabe fibers: FD-42G, FD-42GW spot ens Ambient temperature: 4 to +7 C 4 to +58 F (Note) For refective type fiber Zoom ens Finest spot ens Finest spot ens Zoom ens side-view type FX-MR2 FX-MR3 FX-MR6 FX-MR5 Screw-in depth Distance to foca point Distance to foca point Distance to foca point Spot diameter Spot diameter Screw-in depth Spot diameter Note: Refer to p.26 for the ambient temperature of fibers to be used in combination. ens (For square M3 refective fiber) For Square M3 refective fiber For Square M3 refective fiber Type Type Finest spot ens Zoom ens Parae ight ens Spot diameter (mm in)(note) ø. ø.4 approx. ø.5 ø.6 approx. ø.2 ø.8 approx. ø.4 ø.6 approx. Distance to foca point (mm in)(note) 7 ± ±.2 The spot diameter is adjustabe from ø.7 to ø2 mm ø.28 to ø.79 in according to how much the fiber is screwed in. Appicabe fibers: FD-42G, FD-42GW Ambient temperature: 4 to +7 C 4 to +58 F (Note) Accessory: MS-EX3 (mounting bracket) Extremey fine spot of ø.5 mm ø.6 in approx. achieved. Appicabe fibers: FD-EG3, FD-EG3, FD-42G, FD-42GW, FD-32G, FD-32GX Ambient temperature: 4 to +7 C 4 to +58 F (Note) Extremey fine spot of ø. mm ø.4 in approx. achieved. Appicabe fibers: FD-EG3, FD-EG3, FD-42G, FD-42GW, FD-32G, FD-32GX Ambient temperature: 2 to +6 C 4 to +4 F (Note) FX-MR2 is converted into a side-view type and can be mounted in a very sma space. Appicabe fibers: FD-42G, FD-42GW Ambient temperature: 4 to +7 C 4 to +58 F (Note) ens Shape Mode No. (mm in) FX-MR7 Shape Sensing range for FX- series Screw-in depth Distance to foca point Spot diameter 7 mm.276 in 8.5 mm.728 in approx. ø.7 mm ø.28 in 2 mm.472 in 27 mm.63 in approx. ø.2 mm ø.47 in 4 mm.55 in 43 mm.693 in approx. ø2. mm ø.79 in Sensing range for FX- series mode No. Distance to foca point Spot diameter FD-EG3 7.5 ±.5 mm.295 in ±.2 in ø.5 mm ø.6 in approx. FD-EG3 7.5 ±.5 mm.295 in ±.2 in ø.3 mm ø.2 in approx. FD-42G/42GW FD-32G/32GX 7.5 ±.5 mm.295 in ±.2 in ø.5 mm ø.2 in approx. Sensing range for FX- series mode No. Distance to foca point Spot diameter FD-EG3 7 ±.5 mm.276 in ±.2 in ø. mm ø.4 in approx. FD-EG3 7 ±.5 mm.276 in ±.2 in ø.2 mm ø.8 in approx. FD-42G/42GW FD-32G/32GX 7 ±.5 mm.276 in ±.2 in ø.4 mm ø.6 in approx. Sensing range for FX- series mode No. Distance to foca point Spot diameter 8 mm.35 in 3 mm.52 in approx. ø.5 mm ø.2 in mm.394 in 5 mm.59 in approx. ø.8 mm ø.3 in 4 mm.55 in 3 mm.8 in approx. ø3. mm ø.8 in Emitting fiber core (mm in) Mode No. ø.25 ø.5 FD-R33EG ø.25 ø.5 FD-EG3 ø.75 ø.7 FD-R34EG ø.25 ø. FD-R32EG ø.25 ø. FD-EG3 ø.5 ø.2 FD-R3G ø.5 ø.2 FD-32G ø.5 ø.2 FD-32GX ø.5 ø.2 FD-42G ø.5 ø.2 FD-42GW ens Appicabe fibers Spot diameter Sensing range (mm in)(note) (mm in)(note) Shape Emitting fiber Mode No. Mode No. (mm in) core (mm in) ø.4 to ø2. ø.6 to ø.79 approx. 5 ø.25 ø.5 FD-R33EG, FD-EG3 ø.4 to ø2.2 ø.6 to ø.87 approx..59 to 3 ø.75 ø.7 FD-R34EG FX-MR8 ø.5 to ø2.5 ø.2 to ø.98 approx..394 to.8 ø5 ø.97 ø.25 ø. FD-R32EG, FD-EG3 ø.8 to ø3.5 ø.3 to ø.38 approx. ø.5 ø.2 FD-R3G, FD-32G, FD-32GX, FD-42G, FD-42GW ø4. ø.57 approx. to 3 to.8 ø5 ø.97 ø5 ø FX-MR9 Note: Spot diameter, distance to foca point and sensing range are specified for FX- series. ø.25 ø.5 FD-R33EG, FD-EG3 ø.75 ø.7 FD-R34EG ø.25 ø. FD-R32EG, FD-EG3 ø.5 ø.2 FD-R3G, FD-32G, FD-32GX, FD-42G, FD-42GW Ramco Nationa nsaes@ramcoi.com IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F

13 3 Digita Sensor FX- SERIES SPECIFICATIONS IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Type Standard type ong sensing range type Cabe set Cabe set NPN output FX-(-Z) (Note 5) FX--CC2 FX-2(-Z) (Note 5) FX-2-CC2 Item PNP output FX-P(-Z) (Note 5) FX-P-CC2 FX-2P(-Z) (Note 5) FX-2P-CC2 Suppy votage 2 to 24 V DC ± % Rippe P-P % or ess Mode No. Power consumption Output Output operation Short-circuit protection Externa input Response time Sensitivity Operation indicator Digita dispay Fine sensitivity adjustment function Timer function Norma operation: 72 mw or ess (Current consumption 3 ma or ess at 24 V suppy votage) ECO mode: 6 mw or ess (Current consumption 25 ma or ess at 24 V suppy votage) <NPN output type> <PNP output type> NPN open-coector PNP open-coector Maximum sink current: ma Maximum source current: ma Appied votage: 3 V DC or ess (between output and V) Appied votage: 3 V DC or ess (between output and +V) Residua votage:.5 V or ess (at ma sink current) Residua votage:.5 V or ess (at ma source current) <NPN output type> NPN non-contact input Signa condition High: +8 V to +V DC or Open ow: to +2 V DC (Source current.5 ma or ess) Input impedance: kω approx. Emission frequency : 25 µs or ess (factory defaut ) Emission frequency : 45 µs or ess Emission frequency 2: 5 µs or ess Emission frequency 3: 6 µs or ess Seectabe either ight-on or Dark-ON, at SET mode Incorporated <PNP output type> PNP non-contact input Signa condition High: +4 V to +V DC (Sink current.5 to 3 ma) ow: to +.6 V DC or Open Input impedance: kω approx. 2-point teaching / imit teaching / Fu-auto teaching Orange ED (ights up when the output is ON) 4 digits (green) + 4 digits (red) CD dispay Incorporated Emission frequency : 2.5 ms or ess (factory defaut ) Emission frequency 2: 2.8 ms or ess Emission frequency 3: 3.2 ms or ess Emission frequency 4: 5. ms or ess ON-deay / OFF-deay timer, switchabe either effective or ineffective [Timer period: ms, 5 ms, ms, 2 ms, 4 ms, 5 ms, ms, 5 ms,, ms] Emission amount function 3-eve + Auto (from production in December 27) Interference prevention function Environmenta resistance Ambient temperature Ambient humidity Ambient iuminance Incorporated Emission frequency seection method (Note 2) (Functions at emission frequency, 2 or 3) Incorporated Emission frequency seection method (Note 2) (Functions at emission frequency, 2, 3 or 4) to +55 C +4 to +3 F (If 4 to 7 units are mounted cose together: to +5 C +4 to +22 F, if 8 to 6 units are mounted cose together: to +45 C +4 to +3 F) (No dew condensation or icing aowed), Storage: 2 to +7 C 4 to +58 F 35 to 85 % RH, Storage: 35 to 85 % RH Incandescent ight: 3, x at the ight-receiving face Votage withstandabiity, V AC for one min. between a suppy terminas connected together and encosure (Note 3) Insuation resistance 2 MΩ, or more, with 25 V DC megger between a suppy terminas connected together and encosure (Note 3) Vibration resistance Shock resistance Emitting eement (moduated) Materia to 5 Hz frequency,.75 mm.3 in ampitude in X, Y and Z directions for two hours each 98 m/s 2 acceeration ( G approx.) in X, Y and Z directions for five times each Red ED (Peak emission waveength: 643 nm.25 mi) Encosure: Poycarbonate, Key switch: Poycarbonate, ock ever: PBT Connecting method Connector (Note 4) Cabe ength Weight Accessory Net weight: 5 g approx. Gross weight: 35 g approx. FC-FX- (Protection cover): pc. (Note 6) Tota ength up to m ft is possibe with.3 mm 2, or more, cabe. Net weight: 5 g approx. Gross weight: 75 g approx. FC-FX- (Protection cover): pc. (Note 6) CN-4A-C2 (Connector attached cabe, ong): pc. Net weight: 5 g approx. Gross weight: 35 g approx. FC-FX- (Protection cover): pc. (Note 6) Net weight: 5 g approx. Gross weight: 75 g approx. FC-FX- (Protection cover): pc. (Note 6) CN-4A-C2 (Connector attached cabe, ong): pc. Notes: ) Where measurement conditions have not been specified precisey, the conditions used were an ambient temperature of +23 C F. 2) When using the interference prevention function, set the emission frequencies for the ampifiers to be covered by the interference prevention function to different frequency vaues. However, the interference prevention function does not operate at emission frequency (factory defaut ) for the FX-(P)(-Z) / FX-(P)-CC2. 3) The votage withstandabiity and the insuation resistance vaues given in the above tabe are for the ampifier ony. 4) Connector attached cabe CN-4A-C2 is not attached to the modes that have no -CC2 at the end of the mode Nos. Make sure to use the optiona connector attached cabe CN-4A(-R)-C or the connector CN-4A, or a connector manufactured by J.S.T. Mfg., td. (contact: SPHD-T-P.5, housing: PAP-4V-S). 5) Mode Nos. having the suffix -Z are M8 pug-in connector type. Make sure to use the optiona M8 attached connector cabe CN-24A-C. 6) Protection cover FC-FX- has been attached from production in Juy, 2. Ramco Nationa nsaes@ramcoi.com

14 i r i t Digita Sensor FX- SERIES 32 I/O CIRCUIT AND WIRING DIAGRAMS FX- (-Z/-CC2) NPN output type I/O circuit diagram Termina No. Coor code of cabe with connector Termina arrangement diagram Connector type * Sensor circuit +8 V D Tr ZD Interna circuit (Brown) +V (Back) Output 2 (Bue) V 4 Users circuit ma max. () Externa input 3 oad Symbos D : Reverse suppy poarity protection diode ZD: Surge absorption zener diode Tr : NPN output Non-votage contact or NPN open-coector or High (+8 V to +V DC, or open): Ineffective ow [ to +2 V DC (source current.5 ma or ess)]: Effective * to 24 V DC ± % M8 pug-in connector type Termina No. Termina No. Function +V Output Externa input V Function +V Output Externa input V IGHT FOW PARTICUAR SIMPE ITY FX- P(-Z/-CC2) I/O circuit diagram u c r c o s n e S Tr D Z D Termina No. Coor code of cabe with connector (Brown) +V () Externa input 3 ma max. 2 (Back) Output oad (Bue) V 4 * to 24 V DC ± % Termina arrangement diagram Connector type Termina No. PNP output type Function +V Output Externa input V PC VISUAIZATION Interna circuit Users circuit * Symbos D : Reverse suppy poarity protection diode ZD: Surge absorption zener diode Tr : PNP output Non-votage contact or PNP open-coector or M8 pug-in connector type Termina No Function +V Output Externa input V Seection s Ampifiers FX-5 High [ +4 V to +V DC (sink current.5 to 3 ma)]: Effective ow ( to +.6 V DC, or open): Ineffective FX- FX-3 FX-4 FX-3-F7/ FX-3-F Ramco Nationa nsaes@ramcoi.com

15 33 Digita Sensor FX- SERIES SENSING CHARACTERISTICS (TYPICA) IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 FX- FX-3 FX-4 FX-3-F7/ FX-3-F Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) FT-3S Parae deviation FX-2 FX eft Center Right FT-43 Parae deviation, , FT-S2W Parae deviation FX-2 FX- FX-2, 5 5, eft Center Right FX eft Center Right FD-4S Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) FT-3W Parae deviation 25 2 FX FX eft Center Right FT-45X Parae deviation, FX , 5 5, eft Center Right FT-S3W Thru-beam type Parae deviation FX-2 FX FX eft Center Right Sensing fied Horizonta direction Vertica direction FX-2 FX- Thru-beam type Thru-beam type Thru-beam type non-gossy 2mm in eft Right eft Center Right Setting distance (mm in) Thru-beam type Thru-beam type Refective type FX-2 non-gossy 2mm in FX- 5 Up Down Down Center Up Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) FT-42S Parae deviation, FX-2 4 FX eft Center Right FT-A FD-32G Refective type Sensing fied eft non-gossy 2mm in Right FX-2 FX eft Center Right Setting distance (mm in) Setting distance (mm in) FT-42W Parae deviation FX-2 4 FX eft Center Right Parae deviation Horizonta direction Vertica direction 4, , 8. FX-2 FX- 2, 78.74, eft Center Right FD-4W Setting distance (mm in) 4, , 8. 2, 78.74, FD-32GX Sensing fied FX-2 FX- Refective type non-gossy 2mm in FX-2 FX- 8mm.35in Down Center Up eft Right eft Center Right Sensing fied Horizonta direction Vertica direction FX-2 FX- Thru-beam type non-gossy 2mm in eft Right eft Center Right Setting distance (mm in) 25 Thru-beam type Thru-beam type 2 FX-2 non-gossy mm FX- in 5 Up Down Down Center Up Ramco Nationa nsaes@ramcoi.com Refective type

16 Digita Sensor FX- SERIES 34 SENSING CHARACTERISTICS (TYPICA) Setting distance (mm in) Setting distance (mm in) Setting distance (mm in) FD-42G Sensing fied FX-2 FX- non-gossy 2mm in eft Right eft Center Right FD-6W Setting distance (mm in) FD-42GW Sensing fied FX-2 FX- non-gossy 2mm in eft Right eft Center Right Sensing fied Horizonta direction Vertica direction FX-2 FX- non-gossy 2mm in eft Right eft Center Right FD-64X Sensing fied Horizonta direction 25 2 Refective type 5 FX non-gossy FX- 2mm in 5 eft Right eft Center Right Setting distance (mm in) Setting distance (mm in) 25 2 FX-2 non-gossy mm FX- in 5 Up Down Down Center Up Setting distance (mm in) Setting distance (mm in) FD-6G Sensing fied FX-2 FX- eft Right eft Center Right FD-62 non-gossy 2mm in Sensing fied Horizonta direction Vertica direction FX-2 FX- non-gossy 2mm in eft Right eft Center Right FD-S32W Setting distance (mm in) FX-2 3 non-gossy.8 2mm FX- in 2 Up Down Down Center Up Sensing fied Vertica direction Horizonta direction Vertica direction 25 2 Refective type Refective type Refective type 5 FX non-gossy FX- 2mm in 5 Up Down eft Center Right Setting distance (mm in) Refective type FX-2 FX- non-gossy 2mm in eft Right eft Center Right Setting distance (mm in) Refective type Refective type non-gossy 2mm in FX-2 FX- Up Down Down Center Up IGHT FOW PARTICUAR SIMPE ITY PC VISUAIZATION Seection s Ampifiers FX-5 Setting distance (mm in) FD-S33GW Sensing fied Refective type FX-2 FX- non-gossy 2mm in eft Right eft Center Right Ramco Nationa nsaes@ramcoi.com FX- FX-3 FX-4 FX-3-F7/ FX-3-F