Adjustable Range Reflective Photoelectric Sensor.

Transcription

1 97 SER PHOTOEECTRIC PHOTOEECTRIC djustabe Range Refective Photoeectric EQ-3 SERIES Reated Information Genera terms and conditions...p. Gossary of terms...p.983~ seection guide...p.~ / P.9~ Genera precautions...p.98~ Conforming to EMC irective INUCTIVE PRTICUR MESURE CONTRO EVICES SER SUNX website PNP output type avaiabe Interference prevention Unaffected by coor or materia, m (.5 ft) distance adjustabe range refective sensing CX-4 EX- EX- EX-3 EX-4 EQ-3 EQ-5 -S PX- RT- Hardy affected by coor or background s the EQ-3 series is incorporated with a -segment photodiode as the receiving eement with a unique circuitry, it detects an at the same distance regardess of its coor or the background beyond the adjusted sensing range. However, when the background is specuar, it may be necessary to change the ange of the sensor. EQ-34: Correation between materia ( mm in) and sensing range (typica) range (m ft) m.5 ft m 3.8 ft. m.5 ft Gray nongossy (ightness: 5) Cardboard Pywood Back rubber These bars indicate the sensing range with the respective s when the distance adjuster is set at the sensing range of m.5 ft, m 3.8 ft and. m.5 ft ong, each, with white. ong sensing range m.5 ft The EQ-3 series can detect an m.5 ft away. It is suitabe for various appications, such as, sensing s or positioning s traveing on a wide assemby ine, etc. m.5 ft Two distances (far and near) can be set With, two sensing distances, Far (Main) and, can be set. Hence, one sensor can suffice where, earier, two were required. Far (Main) Near (Sub)

2 ORER GUIE P.99 SPECIFICTIONS P.3 I/O CIRCUIT IGRMS P.3 djustabe Range Refective Photoeectric EQ-3 SERIES 98 SENSING CHRCTERISTICS P.3~ PRECUTIONS FOR PROPER P.33~ IMENSIONS P.35~ PPICTIONS etecting traveing cardboard boxes etecting eve in hopper Upper imit ower imit SER PHOTOEECTRIC PHOTOEECTRIC ENVIRON RESISTNCE Insusceptibe to contamination on ens The fixed-focus sensing keeps the detectabiity better than diffuse refective type sensors even if the ens is contaminated by dirt, dust, mist, or smoke under an uncean environment. OPERBIITY Mechanica -turn adjuster with indicator It features a mechanica -turn distance adjuster with an indicator that shows the set distance at a gance. djuster indicator N E R F R istance adjuster (-turn) INUCTIVE PRTICUR MESURE CONTRO EVICES SER Waterproof It has IP7 protection. It can be used in paces spashed with water. Note: However, take care that if it is exposed to water spashes during operation, it may detect a water drop itsef. Principe of adjustabe range refective sensing with -segment photodiode Norma refective type sensors operate by sensing the variation in the amount of incident beam. However, the adjustabe range refective sensing type sensor incorporating the -segment photodiode operates by sensing the variation in the incident beam ange. Thus, the output is activated according to the distance of the from the sensor. This system heps the EQ-3 series in being unaffected by coor or a background, enabing stabe sensing. -segment photodiode Emitting E is based on the difference in the incident beam ange of the dotted ine and the soid ine in the above figure. MOUNTING / SIZE Compact It saves space, since a miniaturized housing of W H8 4 mm W.787 H in has been designed for the adjustabe range refective sensing sensor even though the adjustabe sensing range is m.5 ft ong. VRIETIES 4 mm.575 in 8 mm.77 in Pug-in connector type is avaiabe Pug-in connector type, which can be easiy disconnected for repacement is avaiabe. In case a probem occurs, anyone can repace the sensor in a minute. (Excuding ) ø4 mm ø.55 in Pug-in connector type EQ-34-J EQ-34-PN-J M connector (IEC conforming) Mating cabe CN-4 -C (Cabe ength: m.5 ft) CN-4 -C5 (Cabe ength: 5 m.44 ft) mm.787 in CX-4 EX- EX- EX-3 EX-4 EQ-3 EQ-5 -S PX- RT-

3 99 djustabe Range Refective Photoeectric EQ-3 SERIES SER EECTRIC EECTRIC ORER GUIE Type ppearance djustabe range (Note) Mode No. Output NPN output EQ-34 NPN open-coector transistor PNP output. to m.5 to.5 ft EQ-34-PN PNP open-coector transistor Two outputs Two NPN open-coector transistor outputs INUCTIVE PRTICUR CONTRO EVICES SER NOTE: Mounting bracket is not suppied with the sensor. Pease seect from the range of optiona sensor mounting brackets (two types). Note: The adjustabe range stands for the maximum sensing range which can be set with the adjuster. The sensor can detect an. m.38 ft, or more, away. However, the detectabe range of type of begins at. m.5 ft. Pug-in connector type (Not avaiabe for ) Pug-in connector type (standard: cabe type) is aso avaiabe. (excuding ) When ordering this type, suffix -J to the mode No. Pease order the suitabe mating cabe separatey. Mode No.: EQ-34-J, EQ-34-PN-J Non-detectabe range. m.38 ft ctua sensing range of the sensor. m.5 ft djustabe range CN-4-C m.5 ft Mating cabe Type Mode No. escription 43.5 mm.73 in ø4 mm ø.55 in CX-4 EX- EX- Straight Ebow CN-4-C CN-4-C5 CN-4-C CN-4-C5 ength: m.5 ft ength: 5 m.44 ft ength: m.5 ft ength: 5 m.44 ft.34 mm 4-core cabtyre cabe with connector on one end Cabe outer diameter: ø5 mm ø.97 in CN-4-C ø5 mm ø.97 in EX-3 EX-4 EQ-3 EQ-5 5 m.44 ft cabe ength type 5 m.44 ft cabe ength type (standard : m.5 ft) is aso avaiabe for NPN output type and two outputs type. When ordering this type, suffix -C5 to the mode No. Mode No.: EQ-34-C5, -C5 9 mm.4 in 3 mm. in ø4 mm ø.55 in ø5 mm ø.97 in -S PX- RT- esignation Mode No. escription mounting bracket MS-EQ3- MS-EQ3- Back anged mounting bracket Foot anged mounting bracket Note: The pug-in connector type does not aow use of some sensor mounting brackets because of the protrusion of the connector. mounting bracket MS-EQ3- Two M4 (ength 5 mm.984 in) screws with washers and two M4 nuts are attached. MS-EQ3- Two M4 (ength 5 mm.984 in) screws with washers and two M4 nuts are attached.

4 djustabe Range Refective Photoeectric EQ-3 SERIES 3 SPECIFICTIONS Type NPN output PNP output Two outputs Item Mode No. EQ-34 EQ-34-PN djustabe range (Note ) range with white at setting distance m.5 ft Hysteresis Repeatabiity Suppy votage. to m.5 to.5 ft. to m.38 to.5 ft % or ess of operation distance (With white ) Far (Main):. to m.5 to.5 ft : Refer to diagram in (Note 3) Far (Main):. to m.38 to.5 ft :. to m.5 to.5 ft [with distance for adjuster at max.] ong sensing axis: mm.394 in or ess, Perpendicuar to sensing axis: mm.39 in or ess (with white ) to 3 V C Rippe P-P % or ess Current consumption 5 m or ess 55 m or ess 9 m or ess Output Utiization category Output operation Short-circuit protection Response time Operation indicator NPN open-coector transistor Maximum sink current: m ppied votage: 3 V C or ess (between output and V) Residua votage: V or ess (at m sink current).4 V or ess (at m sink current) PNP open-coector transistor Maximum source current: m ppied votage: 3 V C or ess (between output and V) Residua votage: V or ess (at m source current).4 V or ess (at m source current) C- or C-3 Switchabe either etection-on or etection-off Incorporated ms or ess Red E (ights up when the output is ON) <Far (Main) output, output> NPN open-coector transistor Maximum sink current: m ppied votage: 3 V C or ess (between output and V) Residua votage: V or ess (at m sink current).4 V or ess (at m sink current) Far (Main) output: Red E ights up when the Far (Main) output is ON output: Red E ights up when the Near (Sub) output is ON Stabiity indicator Green E (ights up under stabe ight received condition or stabe dark condition) (Note 4) istance adjuster -turn mechanica adjuster with pointer Far (Main): -turn mechanica adjuster with pointer : Variabe adjuster utomatic interference prevention function Incorporated (Note 5) Poution degree 3 (Industria environment) Protection IP7 (IEC) (Refer to p.984 for detais of standards.) mbient temperature to 55 C 4 to 3 F (No dew condensation or icing aowed), Storage: 5 to 7 C 3 to 58 F mbient humidity 35 to 85 % RH, Storage: 35 to 85 % RH mbient iuminance Incandescent ight: 3, x at the ight-receiving face EMC EN Votage withstandabiity, V C for one min. between a suppy terminas connected together and encosure Insuation resistance MΩ, or more, with 5 V megger between a suppy terminas connected together and encosure Vibration resistance to 55 Hz frequency,.5 mm.59 in ampitude ( G max.) in X, Y and Z directions for two hours each Shock resistance 5 m/s acceeration (5 G approx.) in X, Y and Z directions for three times each Emitting eement Infrared E (Peak emission waveength: 88 nm.35 mi, moduated) Materia Encosure: Poyayate and Poyethyene terephthaate, ens: Poyayate Cabe.3 mm 3-core (: 4-core) cabtyre cabe, m.5 ft ong Cabe extension Extension up to tota m ft is possibe with.3 mm, or more, cabe. Weight Net weight: 5 g approx., Gross weight: g approx. ccessory djusting screwdriver: pc. Environmenta resistance Notes: ) Where measurement conditions have not been specified precisey, the conditions used were an ambient temperature of 3 ºC 73.4 F. ) The adjustabe range stands for the maximum sensing range which can be set with the adjuster. The sensor can detect an. m.38 ft, or more, away. However, the detectabe area of the type of the begins at. m.5 ft. Non-detectabe range. m.38 ft ctua sensing range of the sensor.m.5 ft djustabe range m.5 ft 3) The distance adjustabe range,, changes with the setting of the Far (Main) distance,, as shown in the tabe beow. distance adjustabe range.5 distance adjustabe range (m ft) Far (Main) setting distance (m ft) Far (Main) setting distance distance adjustabe range m.5 ft to m 3.8 to.5 ft.5 m 4.9 ft.85 to.5 m.789 to 4.9 ft m 3.8 ft.5 to m.33 to 3.8 ft.5 m.4 ft.35 to.5 m.48 to.4 ft. m.5 ft. m.5 ft SER EECTRIC EECTRIC INUCTIVE PRTICUR CONTRO EVICES SER CX-4 EX- EX- EX-3 EX-4 EQ-3 EQ-5 -S PX- RT- 4) Refer to PRECUTIONS FOR PROPER (p.33) for detais of the stabiity indicator. 5) etection may become unstabe depending on the setting conditions or the sensing s. fter setting up this product, make sure to check operations using actua sensing s.

5 3 djustabe Range Refective Photoeectric EQ-3 SERIES SER EECTRIC EECTRIC INUCTIVE PRTICUR EQ-34 I/O CIRCUIT N WIRING IGRMS I/O circuit diagram circuit Tr Interna circuit Z Coor code / Connector pin No. of the pug-in connector type (Brown / ) V oad (Back / 4) Output m max. (Bue / 3) V Users circuit Symbos : Reverse suppy poarity protection diode Z: Surge absorption zener diode Tr : NPN output transistor to 3 V C Wiring diagram Brown / Back / 4 Bue / 3 oad Connector pin position (Pug-in connector type) Not connected V Connector pin No. NPN output type to 3 V C CONTRO EVICES EQ-34-PN I/O circuit diagram Coor code / Connector pin No. of the pug-in connector type 3 V Wiring diagram 4 Output PNP output type SER circuit Tr Z (Brown / ) V m max. (Back / 4) Output oad (Bue / 3) V to 3 V C Brown / Back / 4 Bue / 3 oad to 3 V C Interna circuit Users circuit Connector pin position (Pug-in connector type) CX-4 EX- Symbos : Reverse suppy poarity protection diode Z: Surge absorption zener diode Tr : PNP output transistor Not connected 3 V V Connector pin No. 4 Output EX- EX-3 EX-4 I/O circuit diagram Wiring diagram Two outputs type EQ-3 Coor code EQ-5 (Brown) V Brown -S PX- RT- circuit Tr Tr Z Interna circuit Z (Back) Far (Main) output m max. () output (Bue) V Users circuit oad m max. oad Symbos : Reverse suppy poarity protection diode Z, Z: Surge absorption zener diode Tr, Tr : NPN output transistor to 3 V C Back Bue oad oad to 3 V C

6 MOE STB MOE MOE STB MOE MOE MOE djustabe Range Refective Photoeectric EQ-3 SERIES 3 SENSING CHRCTERISTICS (TYPIC) EQ-34 EQ-34-PN SER Setting distance (m ft) range (m ft) fieds Setting distance: m 3.8 ft eft Center Right Yeow Orange mm Non-gossy Red Brown (ightness: 5) Green Bue Gray.787 Back Setting distance (m ft) Setting distance:.5 m 4.9 ft Setting distance: m.5 ft m.5 ft m 3.8 ft. m.5 ft mm Non-gossy (ightness: 5) eft Center Right Correation between coor ( mm ) and sensing range These bars indicate the sensing range with the respective coors when the distance adjuster is set at the sensing range of m.5 ft, m 3.8 ft and. m.5 ft ong, each, with white coor. The sensing distance varies depending aso on materia..787 Setting distance (m ft) range (m ft) eft Center Right Gray nongossy (ightness: 5) mm Non-gossy Cardboard (ightness: 5) Pywood Back rubber.787 istance (m ft) Emitted beam m ft 3.8 m ft..5 m ft ø4 mm ø.8 in ø34 mm ø.339 in ø4 mm ø.945 in ø7 mm ø.9 in ø mm ø.787 in Correation between materia ( mm ) and sensing range These bars indicate the sensing range with respective s when the distance adjuster is set at the sensing range of m.5 ft, m 3.8 ft and. m.5 ft ong, each, with white. EECTRIC EECTRIC INUCTIVE PRTICUR CONTRO EVICES SER Setting distance (m ft) fieds Far (Main) [Far (Main) setting distance: m 3.8 ft] (ightness: 5) mm Non-gossy Setting distance (m ft) Far (Main) Far (Main) [Far (Main) setting distance:.5 m 4.9 ft] [Far (Main) setting distance: m.5 ft] (ightness: 5) mm Non-gossy Setting distance (m ft) (ightness: 5) mm Non-gossy STB CX-4 EX- EX- EX-3 EX-4 EQ-3 EQ-5 Setting distance (m ft) eft Center Right eft Center Right eft Center Right [Far (Main) setting distance: m 3.8 ft] [Far (Main) setting distance:.5 m 4.9 ft] [Far (Main) setting distance: m.5 ft] eft adjuster max. adjuster min. (ightness: 5) mm Non-gossy STB Gray (ightness: 5).394 Center Right.787 Setting distance (m ft) Gray (ightness: 5).787 (ightness: 5) adjuster max. adjuster min. mm Non-gossy STB eft Center Right.787 Setting distance (m ft) Gray (ightness: 5) adjuster max. adjuster min. (ightness: 5).787 mm Non-gossy STB eft Center Right.787 istance (m ft) Emitted beam ø4 mm ø.8 in ø34 mm ø.339 in ø4 mm ø.945 in ø7 mm ø.9 in ø mm ø.787 in -S PX- RT-

7 33 djustabe Range Refective Photoeectric EQ-3 SERIES SER SENSING CHRCTERISTICS (TYPIC) EECTRIC EECTRIC INUCTIVE PRTICUR range (m ft) Correation between coor ( mm ) and sensing range Yeow Orange Red Brown Green Bue Gray Back Far (Main) m.5 ft m 3.8 ft These bars indicate the sensing range with respective coors when the distance adjuster is set at the sensing range of Far (Main) m.5 ft and m 3.8 ft ong, each, with white coor. The sensing distance varies depending aso on materia. range (m ft) Correation between materia ( mm ) and sensing range Back nongossy (ightness: 5) Cardboard Pywood Back rubber Far (Main) m.5 ft m 3.8 ft These bars indicate the sensing range with re- spective s when the distance adjuster is set at the sensing range of Far (Main) m.5 ft and Near (Sub) m 3.8 ft ong, each, with white. PRECUTIONS FOR PROPER Refer to p.98~ for genera precautions. CONTRO EVICES SER Never use this product as a sensing device for personne protection. In case of using sensing devices for personne protection, use products which meet aws and standards, such as OSH, NSI or IEC etc., for personne protection appicabe in each region or country. Mounting The tightening torque shoud be.8 N m or ess. M4 nut M4 (ength 5 mm.984 in) screw with washers mounting backet MS-EQ3- (Optiona) CX-4 EX- EX- EX-3 EX-4 EQ-3 EQ-5 -S PX- RT- Stabiity indicator Since the EQ-3 series uses a -segment photodiode as its receiving eement, and sensing is done based on the difference in the incident beam ange of the refected beam from the sensing, the output and the operation indicator operate according to the distance. Further, the stabiity indicator shows the margin of the incident ight intensity and not that of the distance. Hence, the distance at which it ights up/off depends on the refectivity and is not at a reated to the output operation. o not use the sensor when the stabiity indicator is off (unstabe ight received condition), since the sensing wi be unstabe. Output (operation indicator) (In case of etection-on) Stabiity indicator (Back ) Stabiity indicator ( ) s Setting distance Stabe ight received condition Unstabe ight received condition Stabe ight received condition Stabe dark condition Unstabe ight received condition Stabe dark condition ON (ights up) OFF (ights off) ights up ights off ights up ights off o not use during the initia transient time (5 ms) after the power suppy is switched on. When connecting the mating cabe to the pug-in connector type, the tightening torque shoud be.4 N m or ess. Care must be taken regarding the sensor mounting direction with respect to the s direction of movement. o not make the sensor detect an in this direction because it may cause unstabe operation. When detecting a specuar (auminum or copper foi) or an having a gossy surface or coating, pease take care that there are cases when the may not be detected due to a sma change in ange, wrinkes on the surface, etc. When a specuar body is present beow the sensor, use the sensor by titing it sighty upwards to avoid wrong operation. Specuar face If a specuar body is present in the background, wrong operation may be caused due to a sma change in the ange of the background body. In that case, insta the sensor at an incination and confirm the operation with the actua sensing. Take care that some s may produce a dead zone right (ess than. m) in front of the sensor. Tit

8 djustabe Range Refective Photoeectric EQ-3 SERIES 34 PRECUTIONS FOR PROPER istance adjustment <djusters> Far (Main) adjuster indicator Shows how much the distance adjuster is rotated. STB MOE Far (Main) distance adjuster (-turn) ( ) The sensing range increases ( as it is turned cockwise. ) ) distance adjuster The sensing range increases ( as it is turned cockwise. output operation indicator (Red) ights up when the Near (Sub) output is ON. Stabiity indicator (Green) ights up under stabe ight received condition or stabe dark condition. ( ) Operation mode switch : etection-on : etection-off (Turn the switch fuy.) Far (Main) output operation indicator (Red) ights up when the Far (Main) output is ON. djusting procedure (when the direction of movement of the sensing s is right or eft to the sensor) Far (Main) Step escription istance adjuster Turn the Far (Main) distance adjuster fuy countercockwise to the minimum sensing range position of. m.5 ft approx. Turn fuy Refer to p.98~ for genera precautions. Step escription istance adjuster Turn the distance adjuster fuy countercockwise to the minimum sensing range position. Pace an at the near position, at the required distance from the sensor, turn the Near (Sub) distance adjuster graduay cockwise, and find out point C where the sensor changes to the ight received condition. Remove the from the near position, and pace the for Far (Main) sensing at the sensing position. Turn the distance adjuster further cockwise, and find out point where the sensor changes to the ight received condition again with ony the background. When the sensor does not go to the ight received condition even if the adjuster is fuy turned cockwise, point is this extreme point.. The optimum position to staby detect s for the setting is the center point between C and. Turn fuy C C C Optimum position SER EECTRIC EECTRIC INUCTIVE PRTICUR CONTRO EVICES SER 3 4 Pace an at the far pace at the required distance from the sensor, turn the Far (Main) distance adjuster graduay cockwise, and find out point where the sensor changes to the ight received condition. Remove the, turn the Far (Main) distance adjuster further cockwise, and find out point B where the sensor changes to the ight received condition again with ony the background. When the sensor does not go to the ight received condition even if the adjuster is fuy turned cockwise, point Bis this extreme point in the range. The optimum position to staby detect s for the Far (Main) setting is the center point between and B. * When a sensing is approaching / moving away from the sensor, foow ony steps and respectivey. Since the sensing point may change depending on the sensing, be sure to check the operation with the actua sensing. B Optimum position B * When a sensing is approaching / moving away from the sensor, foow ony steps 5and respectivey. Since the sensing point may change depending on the sensing, be sure to check the operation with the actua sensing. Notes: ) Turn the distance adjuster graduay and ighty with the attached screwdriver. If the distance adjuster is over turned or pressed heaviy, it may be damaged. ) The Far (Main) distance adjustment shoud be done before the distance adjustment. Take care that the setting distance changes with change in the Far (Main) setting distance. Far (Main) output (In case of etection ON) output (In case of etection OFF) setting distance Near Far (Main) distance adjustabe range (. to m.5 to.5 ft) distance adjustabe range Far (Main) setting distance Far ON OFF ON OFF distance adjuster set at the maximum. CX-4 EX- EX- EX-3 EX-4 EQ-3 EQ-5 -S PX- RT-

9 35 djustabe Range Refective Photoeectric EQ-3 SERIES PRECUTIONS FOR PROPER Refer to p.98~ for genera precautions. SER EECTRIC EECTRIC INUCTIVE PRTICUR EQ-34, EQ-34-PN <djusters> djuster indicator Shows how much the distance ( adjuster is rotated. ) Operation indicator (Red) ights up when the ( ) output is ON. N E R F R istance adjuster (-turn) The sensing range increases ( as it is turned cockwise. ) Operation mode switch : etection-on : etection-off (Turn the switch fuy.) Stabiity indicator (Green) ights up under stabe ight received condition ( ) or stabe dark condition. djusting procedure (when the direction of movement of the sensing s is right or eft to the sensor) Step escription istance adjuster Turn the distance adjuster fuy countercockwise to the minimum sensing range position of. m.5 ft approx. Pace an at the required distance from the sensor, turn the distance adjuster graduay cockwise, and find out point where the sensor changes to the ight received condition. N E R F R Turn fuy N E R F R CONTRO EVICES SER 3 4 Remove the, turn the distance adjuster further countercockwise, and find out point B where the sensor changes to the ight received condition again with ony the background. When the sensor does not go to the ight received condition even if the adjuster is fuy turned cockwise, point Bis this extreme point in the range. Optimum The optimum position to staby detect s position is the center point between and B. N E R F R B N E R F R B CX-4 EX- EX- IMENSIONS (Unit: mm in) * When a sensing is approaching / moving away from the sensor, foow ony steps and respectivey. Since the sensing point may change depending on the sensing, be sure to check the operation with the actua sensing. Note: Turn the distance adjuster graduay and ighty with the attached screwdriver. If the distance adjuster is over turned or pressed heaviy, it may be damaged. The C data in the dimensions can be downoaded from the SUNX website: EX-3 EX-4 EQ-34 EQ-34-PN EQ-3 EQ-5 -S PX- RT- istance adjuster (-turn) 5.59 djuster indicator.787 Beamreceiving Center of sensing Beamemitting 8.77 N E R F R Operation mode switch -M4 nut seats (on both sides) -ø4.5 ø.77 mounting hoes Stabiity indicator (Green) Operation indicator (Red) 5.97 ø5.8 ø.8 cabe, m.5 ft ong Far (Main) distance adjuster (-turn) Far (Main) adjuster indicator distance adjuster Beamreceiving Center of sensing Beamemitting MOE STB Operation mode switch Far (Main) output operation indicator (Red) Stabiity indicator (Green) output operation indicator (Red) -M4 nut seats (on both sides) -ø4.5 ø.77 mounting hoes ø5.8 ø.8 cabe, m.5 ft ong

10 djustabe Range Refective Photoeectric EQ-3 SERIES 3 IMENSIONS (Unit: mm in) The C data in the dimensions can be downoaded from the SUNX website: EQ-34-J EQ-34-PN-J SER 5.59 istance adjuster (-turn) djuster indicator.787 Beamreceiving.79 8 Center.77 of sensing Beamemitting M connector N E R F R Operation mode switch Stabiity indicator (Green) Operation indicator (Red) -M4 nut seats (on both sides) -ø4.5 ø.77 mounting hoes ø4.5 ø.57 EECTRIC EECTRIC INUCTIVE PRTICUR MS-EQ3- t t.79 ssemby dimensions Mounting drawing with EQ-34 mounting bracket (Optiona) CONTRO EVICES SER R55.5 R ø4.5 ø Materia: Cod roed carbon stee (SPCC) Two M4 (ength 5 mm.984 in) screws with washers and two M4 nuts are attached Beamreceiving Center of sensing Beamemitting N E R F R 54. t t (.5) (.59) CX-4 EX- EX- EX-3 EX-4 MS-EQ3- mounting bracket (Optiona) EQ-3 t t º R55 R ø4.5 ø Materia: Cod roed carbon stee (SPCC) Two M4 (ength 5 mm.984 in) screws with washers and two M4 nuts are attached ø.4 ø.5 hoe ssemby dimensions Mounting drawing with EQ-34 Beamreceiving Center of sensing Beamemitting t t N E R F R ø.4 ø.5 hoe 7.99 (.5) (.59) EQ-5 -S PX- RT-