MC14504B. Hex Level Shifter for TTL to CMOS or CMOS to CMOS
|
|
|
- Lillian Brooks
- 5 years ago
- Views:
Transcription
1 MCB Hex Level Shifter for TTL to CMOS or CMOS to CMOS The MCB is a hex noninverting level shifter using CMOS technology. The level shifter will shift a TTL signal to CMOS logic levels for any CMOS supply voltage between and volts. A control input also allows interface from CMOS to CMOS at one logic level to another logic level: Either up or down level translating is accomplished by selection of power supply levels DD and CC. The CC level sets the input signal levels while DD selects the output voltage levels. Features UP Translates from a Low to a High oltage or DOWN Translates from a High to a Low oltage Input Threshold Can Be Shifted for TTL Compatibility No Sequencing Required on Power Supplies or Inputs for Power Up or Power Down to 8 dc Operation for DD and CC Diode Protected Inputs to SS Capable of Driving Two LowPower TTL Loads or One LowPower Schottky TTL Load Over the Rated Temperature Range PbFree Packages are Available* MAXIMUM RATINS oltages Referenced to SS ) Symbol Parameter alue Unit CC DC Supply oltage Range. to +8. DD DC Supply oltage Range. to +8. in out I in, I out P D Input oltage Range (DC or Transient) Output oltage Range (DC or Transient) Input or Output Current (DC or Transient) per Pin Power Dissipation, per Package (Note ). to +8.. to DD +. ± ma mw T A Ambient Temperature Range to + C T stg Storage Temperature Range to + C T L Lead Temperature (8Second Soldering) C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.. Temperature Derating: Plastic P and D/DW Packages:. mw/ C From C To C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this highimpedance circuit. For proper operation, in and out should be constrained to the range SS in or out ) DD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either SS or DD ). Unused outputs must be left open. A WL, L YY, Y WW, W PDIP P SUFFIX CASE 8 SOIC D SUFFIX CASE B TSSOP DT SUFFIX CASE 98F SOEIAJ F SUFFIX CASE 9 MARKIN DIARAMS MCBCP AWLYYWW B AWLYWW B ALYW MCB ALYW = Assembly Location = Wafer Lot = Year = Work Week = PbFree Indicator ORDERIN INFORMATION See detailed ordering and shipping information in the package dimensions section on page of this data sheet. *For additional information on our PbFree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Semiconductor Components Industries, LLC, Publication Order Number: MCB/D
2 MCB PIN ASSINMENT LOIC DIARAM CC DD A out F out CC DD A in F in B out B in MODE E out INPUT LEEL SHIFTER OUTPUT C out E in C in SS 8 9 D out D in MODE TTL/CMOS MODE SELECT Mode Select Input Logic Levels Output Logic Levels CC ) TTL CMOS SS ) CMOS CMOS / of package shown. ORDERIN INFORMATION Device Package Shipping MCBCP PDIP Units / Rail MCBCP PDIP (PbFree) Units / Rail MCBD SOIC 8 Units / Rail MCBD SOIC (PbFree) 8 Units / Rail MCBDR SOIC Units / Tape & Reel MCBDR SOIC (PbFree) Units / Tape & Reel MCBDT TSSOP* 9 Units / Rail MCBDTR TSSOP* Units / Tape & Reel MCBF SOEIAJ Units / Rail MCBFEL SOEIAJ Units / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8/D. *This package is inherently PbFree.
3 MCB ELECTRICAL CHARACTERISTICS oltages Referenced to SS ) Characteristic Î Symbol CC dc C C Î C DD dc Min Max Min Î Typ Max Min Max Unit (Note ) Output oltage Level in = Î OL... dc. Î.. Î. Î.. Level in = CC Î OH..9.9Î..9 dc Î.9.9Î.9 Input oltage Level Î IL dc OL =. dc) TTLCMOS OL =. dc) TTLCMOS OL =. dc) CMOSCMOS.. Î... OL =. dc) CMOSCMOS..... OL =. dc) CMOSCMOS. Î...9 Input oltage Level Î IH dc OH = 9. dc) TTLCMOS... Î.. OH =. dc) TTLCMOS..... OH = 9. dc) CMOSCMOS... Î.. OH =. dc) CMOSCMOS..... OH =. dc) CMOSCMOS.. Î.. Output Drive Current I OH OH =. dc) Source...Î.. OH =. dc) OH = 9. dc)..î..9 OH =. dc)..î 8.8. OL =. dc) Sink Î I OL...Î.88. OL =. dc)....9 OL =. dc).. Î 8.8. Input Current Î I in ±. Î ±. ±. ±. Adc Input Capacitance in = ) Î C in Î.. pf Quiescent Current Î I DD or (Per Package) I CC... Î.... Î.. Adc CMOSCMOS Mode.... Quiescent Current I DD. (Per Package) Î...8. Adc TTLCMOS Mode.... Quiescent Current I (Per Package) Î CC Î... TTLCMOS Mode.. Î.... Data labelled Typ is not to be used for design purposes but is intended as an indication of the IC s potential performance.
4 MCB SWITCHIN CHARACTERISTICS (C L = pf, T A = C) Î Characteristic Symbol Shifting Mode Î Î CC DD Limits Min Typ Max dcî Unit (Note ) Î Propagation Delay, High to Low t PHL TTL CMOS.Î Î 8 ns DD > CC. 8 CMOS CMOS Î DD > CC..Î Î CMOS CMOS. 8 Î CC > DD Î. Î 8 Î Î Propagation Delay, Low to High t PLH TTL CMOS DD > CC.Î ns Î Î CMOS CMOS.Î Î Î DD > CC. Î CMOS CMOS Î CC > DD Î.. Î 9 Î Output Rise and Fall Time t TLH, t THL ALL. Î Î ns. Data labelled Typ is not to be used for design purposes but is intended as an indication of the IC s potential performance. 8 Sp, INPUT SWITCHPOINT OLTAE dc) CC = CC = Sp, INPUT SWITCHPOINT OLTAE dc) CC = DD, SUPPLY OLTAE dc) Figure. Input Switchpoint CMOS to CMOS Mode DD, SUPPLY OLTAE dc) Figure. Input Switchpoint TTL to CMOS Mode DD, SUPPLY OLTAE dc) DD, SUPPLY OLTAE dc) CC, SUPPLY OLTAE dc) Figure. Operating Boundary CMOS to CMOS Mode CC, SUPPLY OLTAE dc) Figure. Operating Boundary TTL to CMOS Mode
5 MCB PACKAE DIMENSIONS PDIP P SUFFIX PLASTIC DIP PACKAE CASE 88 ISSUE T A 8 9 B NOTES:. DIMENSIONIN AND TOLERANCIN PER ANSI Y.M, 98.. CONTROLLIN DIMENSION: INCH.. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL.. DIMENSION B DOES NOT INCLUDE MOLD FLASH.. ROUNDED CORNERS OPTIONAL. H F S C K T SEATIN PLANE D PL. (.) M T A M J L M INCHES MILLIMETERS DIM MIN MAX MIN MAX A B....8 C...9. D...9. F..... BSC. BSC H. BSC. BSC J K...8. L.9... M S.... SOIC D SUFFIX PLASTIC SOIC PACKAE CASE B ISSUE J A 9 8 B P 8 PL. (.) M B S NOTES:. DIMENSIONIN AND TOLERANCIN PER ANSI Y.M, 98.. CONTROLLIN DIMENSION: MILLIMETER.. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION.. MAXIMUM MOLD PROTRUSION. (.) PER SIDE.. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE. (.) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. T SEATIN PLANE K C D PL. (.) M T B S A S M R X J F MILLIMETERS INCHES DIM MIN MAX MIN MAX A B.8... C....8 D F BSC. BSC J K....9 M P R....9
MC14001B Series. B Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series BSuffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
MC14001B Series. B Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series B Suffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
MC14001B Series. B-Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series B-Suffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
MC14066B. Quad Analog Switch/Quad Multiplexer
Quad Analog Switch/Quad Multiplexer The MC4066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper,
MC14066B. Quad Analog Switch/Quad Multiplexer
Quad Analog Switch/Quad Multiplexer The MC4066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper,
MC14016B. Quad Analog Switch/ Quad Multiplexer
Quad Analog Switch/ Quad Multiplexer The MC406B quad bilateral switch is constructed with MOS Pchannel and Nchannel enhancement mode devices in a single monolithic structure. Each MC406B consists of four
MARKING DIAGRAMS MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 1.) ORDERING INFORMATION PDIP 14 P SUFFIX CASE 646
The MC14106B hex Schmitt Trigger is constructed with MOS P channel and N channel enhancement mode devices in a single monolithic structure. These devices find primary use where low power dissipation and/or
MC Hex Contact Bounce Eliminator
M4490 Hex ontact Bounce Eliminator The M4490 is cotructed with complementary MOS enhancement mode devices, and is used for the elimination of extraneous level changes that result when interfacing with
MC14066BF. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION PDIP 14 P SUFFIX CASE 646
The MC14066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper, modulator, demodulator and CMOS
MC14513B. BCD To Seven Segment Latch/Decoder/Driver
BCDToSeven Segment Latch/Decoder/Driver CMOS MSI (LowPower Complementary MOS) The MC453B BCDtoseven segment latch/decoder/driver is cotructed with complementary MOS (CMOS) enhancement mode devices and
MARKING DIAGRAMS MAXIMUM RATINGS (Note 1.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648 MC140xxBCP AWLYYWW
The MC14051B, MC14052B, and MC14053B analog multiplexers are digitally controlled analog switches. The MC14051B effectively implements an SP8T solid state switch, the MC14052B a DP4T, and the MC14053B
MC14532B. 8-Bit Priority Encoder
MC4532B 8-Bit Priority Encoder The MC4532B is cotructed with complementary MOS (CMOS) enhancement mode devices. The primary function of a priority encoder is to provide a binary address for the active
MC14521B. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648
The MC452B consists of a chain of 24 flip flops with an input circuit that allows three modes of operation. The input will function as a crystal oscillator, an RC oscillator, or as an input buffer for
MC14538B. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION
The MC14538B is a dual, retriggerable, resettable monostable multivibrator. It may be triggered from either edge of an input pulse, and produces an accurate output pulse over a wide range of widths, the
MC14514B, MC14515B. 4-Bit Transparent Latch / 4-to-16 Line Decoder
MC14514B, MC145B 4-Bit Traparent Latch / 4-to-16 Line Decoder The MC14514B and MC145B are two output optio of a 4 to 16 line decoder with latched inputs. The MC14514B (output active high option) presents
MJD31, MJD31C (NPN), MJD32, MJD32C (PNP)
MJD31, MJD31C (NPN), MJD32, MJD32C (PNP) MJD31C and MJD32C are Preferred Devices Complementary Power Transistors For Surface Mount Applications Designed for general purpose amplifier and low speed switching
MC14040B. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648
The MC14040B 12 stage binary counter is cotructed with MOS P channel and N channel enhancement mode devices in a single monolithic structure. This part is designed with an input wave shaping circuit and
MC3488A. Dual EIA 423/EIA 232D Line Driver
Dual EIA423/EIA232D Line Driver The MC34A dual is singleended line driver has been designed to satisfy the requirements of EIA standards EIA423 and EIA232D, as well as CCITT X.26, X.2 and Federal Standard
MC1496, MC1496B. Balanced Modulators/ Demodulators
MC96, MC96B Balanced Modulators/ Demodulators These devices were designed for use where the output voltage is a product of an input voltage (signal) and a switching function (carrier). Typical applications
Quad Single Supply Comparator
TECNICAL DATA Quad Single Supply Comparator IL339 The IL339 consists of four independent precision voltage comparators with an offset voltage specification as low as 2.0 m max for four comparators which
Quad 2-Input NAND Gate High-Voltage Silicon-Gate CMOS
TECHNICAL DATA Quad 2-Input NAND Gate High-oltage Silicon-Gate CMOS The NAND gates provide the system designer with direct emplementation of the NAND function. Operating oltage Range:.0 to 18 Maximum input
Symbol Parameter Value Unit V DD DC Supply Voltage Range 0.5 to V
MC4046B Phase Locked Loop The MC4046B phase locked loop contains two phase comparators, a voltagecontrolled oscillator (VCO), source follower, and zener diode. The comparators have two common signal inputs,
MM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well as the capability
Low Power Low Offset Voltage Dual Comparators
TECNICAL DATA Low Power Low Offset oltage Dual Comparators IL2903 The IL2903 consists of two independent precision voltage comparators with an offset voltage specification as low as 2.0 m max for two comparators
MC14536B. MARKING DIAGRAMS 16. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION
The MC14536B programmable timer is a 24 stage binary ripple counter with 16 stages selectable by a binary code. Provisions for an on chip RC oscillator or an external clock are provided. An on chip monostable
MC74HC4066A. Quad Analog Switch/ Multiplexer/Demultiplexer. High Performance Silicon Gate CMOS
MC4HC466A Quad Analog Switch/ Multiplexer/Demultiplexer High Performance Silicon Gate CMOS The MC4HC466A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and
MC3403, MC3303. Single Supply Quad Operational Amplifiers
MC0, MC0 Single Supply Quad Operational Amplifiers The MC0 is a low cost, quad operational amplifier with true differential inputs. The device has electrical characteristics similar to the popular MC7C.
MM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
Quad 2-Input Data Selector/Multiplexer with 3-State Outputs High-Performance Silicon-Gate CMOS
TECNICAL DATA IN74C257A Quad 2-Input Data Selector/Multiplexer with 3-State Outputs igh-performance Silicon-ate CMOS The IN74C257A is identical in pinout to the LS/ALS257. The device inputs are compatible
MM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The MM74HC132 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well
Quad 2-Input Data Selectors/Multiplexer
TECNICAL DATA IN74C157A Quad 2-Input Data Selectors/Multiplexer The IN74C157A is identical in pin out to the LS/ALS157. The device inputs are compatible with standard CMOS outputs; with pull up resistors,
M74HC14. Hex Schmitt inverter. Features. Description
Hex Schmitt inverter Features High speed: t PD =12 ns (typ.) at CC = 6 Low power dissipation: I CC = 1 μa (max.) at T A =25 C High noise immunity: H = 1.2 (typ.) at CC = 6 Symmetrical output impedance:
MC33272A, MC33274A, NCV33272A, NCV33274A. Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers
MC33272A, MC3327A, NCV33272A, NCV3327A Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers The MC33272/7 series of monolithic operational amplifiers are quality fabricated with
MM74HC00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description The MM74HC00 NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
NLAST4051. Analog Multiplexer/ Demultiplexer. TTL Compatible, Single Pole, 8 Position Plus Common Off
NLAST45 Analog Multiplexer/ Demultiplexer TTL Compatible, Single Pole, 8 Position Plus Common Off The NLAST45 is an improved version of the MC45 and MC74HC45 fabricated in sub micron Silicon Gate CMOS
PIN ASSIGNMENT B 1 18 C 2 17 f LT 3 16 g BI 4 a LE 5 14 b D 6 13 c A 7 12 d RBI e RBO e f d g a c b DISPLAY TRUTH TABLE Input
BCDToSeven Segment Latch/Decoder/Driver CMOS MSI (LowPower Complementary MOS) The MC14513B BCDtoseven segment latch/decoder/driver is cotructed with complementary MOS (CMOS) enhancement mode devices and
MM74HC86 Quad 2-Input Exclusive OR Gate
MM74HC86 Quad 2-Input Exclusive OR Gate Features Typical Propagation Delay: 9ns Wide Operating oltage Range: 2 6 Low Input Current: 1mA Maximum Low Quiescent Current: 20mA Max. (74 Series) Output Drive
CD4069, CD4069-SMD Inverter Circuits
CD4069, CD4069-SMD Inverter Circuits General Description The CD4069UB consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating range,
CD4069UBC Inverter Circuits
CD4069UBC Inverter Circuits General Description The CD4069UB consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating range, low power
MC74LVXT4066. Quad Analog Switch/ Multiplexer/Demultiplexer. High Performance Silicon Gate CMOS
MC4LVXT466 Quad Analog Switch/ Multiplexer/Demultiplexer High Performance Silicon Gate CMOS The MC4LVXT466 utilizes silicon gate CMOS technology to achieve fast propagation delays, low resistances, and
MC74HCT4066A. Quad Analog Switch/ Multiplexer/Demultiplexer with LSTTL Compatible Inputs. High Performance Silicon Gate CMOS
MC4HCT4066A Quad Analog Switch/ Multiplexer/Demultiplexer with LSTTL Compatible Inputs High Performance Silicon Gate CMOS The MC4HCT4066A utilizes silicon gate CMOS technology to achieve fast propagation
MC34164, MC33164, NCV33164
MC3464, MC3364, NC3364 Micropower Undervoltage Sensing Circuits The MC3464 series are undervoltage sensing circuits specifically designed for use as reset controllers in portable microprocessor based systems
High Performance Silicon Gate CMOS
High Performance Silicon Gate CMOS The MC74HC4316A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF channel leakage current. This bilateral switch/multiplexer/
MC10H352. Quad CMOS to PECL* Translator
Quad CMOS to PECL* Translator Description The MC10H352 is a quad translator for interfacing data between a CMOS logic section and the PECL section of digital systems when only a +5.0 Vdc power supply is
MC74LVX4066. Quad Analog Switch/ Multiplexer/Demultiplexer. High Performance Silicon Gate CMOS
MC4LVX4 Quad Analog Switch/ Multiplexer/Demultiplexer High Performance Silicon Gate CMOS The MC4LVX4 utilizes silicon gate CMOS technology to achieve fast propagation delays, low resistances, and low OFF
Low Power Dual Operational Amplifier
TECNICAL DATA Low Power Dual Operational Amplifier IL38 The IL38 contains two independent high gain operational amplifiers with internal frequency compensation. The two op-amps operate over a wide voltage
LM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
LM393, LM293, LM2903, LM2903V, NCV2903 Low Offset Voltage Dual Comparators The LM393 series are dual independent precision voltage comparators capable of single or split supply operation. These devices
M74HCT04. Hex inverter. Features. Description
Hex inverter Features High speed: t PD = 11 ns (typ.) at =4.5V Low power dissipation: I CC = 1 μa (max.) at T A =25 C Compatible with TTL outputs: V IH = 2 V (min.) V IL = 0.8 V (max) Balanced propagation
CD4538 Dual Precision Monostable
CD4538 Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
MARKING DIAGRAMS LOGIC DIAGRAM PIN ASSIGNMENT ORDERING INFORMATION FUNCTION TABLE DIP 14 N SUFFIX CASE 646 MC74HC4066AN AWLYYWW
High Performance Silicon Gate CMOS The MC74HC466A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF channel leakage current. This bilateral switch/
LM339, LM239, LM2901, LM2901V, NCV2901, MC3302. Single Supply Quad Comparators
LM339, LM239, LM290, LM290V, NCV290, MC3302 Single Supply Quad Comparators These comparators are designed for use in level detection, low level sensing and memory applications in consumer, automotive,
74AC04 74ACT04 Hex Inverter
74AC04 74ACT04 Hex Inverter General Description The AC/ACT04 contains six inverters. Ordering Code: Features I CC reduced by 50% on 74AC only Outputs source/sink 24 ma ACT04 has TTL-compatible inputs November
TCA0372, TCA0372B. 1.0 A Output Current, Dual Power Operational Amplifiers
.0 A Output Current, Dual Power Operational Amplifiers The TCA0372 is a monolithic circuit intended for use as a power operational amplifier in a wide range of applications, including servo amplifiers
Low Power Quad Operational Amplifier
TECNICAL DATA Low Power Quad Operational Amplifier IL324 The IL324 contains four independent high gain operational amplifiers with internal frequency compensation. The four op-amps operate over a wide
CD4724BC 8-Bit Addressable Latch
8-Bit Addressable Latch General Description The CD4724BC is an 8-bit addressable latch with three address inputs (A0 A2), an active low enable input (E), active high clear input (C L ), a data input (D)
LM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293 Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are designed
MC33201, MC33202, MC33204, NCV33202, NCV33204
MC3320, MC33202, MC33204, NCV33202, NCV33204 Low Voltage, RailtoRail Operational Amplifiers The MC3320/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The
74HCT157. Quad 2 Input Data Selectors / Multiplexers. High Performance Silicon Gate CMOS
74HCT57 Quad 2 Input Data Selectors / Multiplexers High Performance Silicon Gate CMOS The 74HCT57 is identical in pinout to the S57. The device inputs are compatible with standard CMOS outputs; with pullup
Synchronous Binary Counter with Synchronous Clear
September 1983 Revised December 2003 MM74HC161 MM74HC163 Synchronous Binary Counter with Asynchronous Clear Synchronous Binary Counter with Synchronous Clear General Description The MM74HC161 and MM74HC163
Output. Single Supply. Output. Input polarity is reversed when GND pin is used as an output. Load Referred to Negative Supply. Output.
Single Comparators The ability to operate from a single power supply of. V to V or V split supplies, as commonly used with operational amplifiers, makes the LM/LM a truly versatile comparator. Moreover,
TL494, NCV494 SWITCHMODE Pulse Width Modulation Control Circuit
SWITCHMODE Pulse Width Modulation Control Circuit The TL494 is a fixed frequency, pulse width modulation control circuit designed primarily for SWITCHMODE power supply control. Features Complete Pulse
LM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293 Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are designed
LM393, LM293, LM2903, LM2903V, NCV2903, NCV2903V. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293, NCV293V Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are
MARKING DIAGRAMS 16 MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 1.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648
查询 CD4553 供应商 The MC14553B 3 digit BCD counter coists of 3 negative edge triggered BCD counters that are cascaded synchronously. A quad latch at the output of each counter permits storage of any given
CD4541BC Programmable Timer
CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,
CD4047BC Low Power Monostable/Astable Multivibrator
Low Power Monostable/Astable Multivibrator General Description The CD4047B is capable of operating in either the monostable or astable mode. It requires an external capacitor (between pins 1 and 3) and
MC74HC4046A. Phase Locked Loop. High Performance Silicon Gate CMOS
Phase Locked Loop High Performance Silicon Gate CMOS The MC74HC446A is similar in function to the MC446 Metal gate CMOS device. The device inputs are compatible with standard CMOS outputs; with pullup
MAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
MC33201, MC33202, MC33204, NCV33202, NCV Low Voltage, Rail-to-Rail Operational Amplifiers
MC332, MC3322, MC3324, NCV3322, NCV3324 Low Voltage, Rail-to-Rail Operational Amplifiers The MC332/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The inputs
MC10EP142, MC100EP V / 5 VНECL 9 Bit Shift Register
MC0EP42, MCEP42 3.3 V / 5 VНECL Bit Shift Register The MC0EP/EP42 is a bit shift register, designed with byte-parity applications in mind. The MC0/EP42 is capable of performing serial/parallel data into
ML Volt Only Driver/Receiver with an Integrated Standby Mode RS 232/EIA 232 E and CCITT V.28
3.3 olt Only Driver/Receiver with an Integrated Standby Mode RS 232/EIA 232 E and CCITT.28 Legacy Device: Motorola MC145583 The ML145583 is a CMOS transceiver composed of three drivers and five receivers
IL386. Low Voltage Audio Power AMP TECHNICAL DATA
TECNICAL DATA Low Voltage Audio Power AMP IL386 The IL386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but
NC7S08 TinyLogic HS 2-Input AND Gate
TinyLogic HS 2-Input AND Gate General Description The NC7S08 is a single 2-Input high performance CMOS AND Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation
MAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
CD4538BC Dual Precision Monostable
CD4538BC Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
TC4584BP,TC4584BF,TC4584BFN
TC484BP/BF/BFN TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC484BP,TC484BF,TC484BFN TC484B Hex Schmitt Trigger The TC484B is the 6-circuit inverter having the Schmitt trigger function at
NC7S86 TinyLogic HS 2-Input Exclusive-OR Gate
TinyLogic HS 2-Input Exclusive-OR Gate General Description The is a single 2-Input high performance CMOS Exclusive-OR Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit
NLAS4051. Analog Multiplexer/ Demultiplexer. TTL Compatible, Single Pole, 8 Position Plus Common Off
NLAS4 Analog Multiplexer/ Demultiplexer TTL Compatible, SinglePole, 8Position Plus Common Off The NLAS4 is an improved version of the MC4 and MC74HC4 fabricated in submicron Silicon Gate CMOS technology
P2I2305NZ. 3.3V 1:5 Clock Buffer
3.3V :5 Clock Buffer Functional Description P2I2305NZ is a low cost high speed buffer designed to accept one clock input and distribute up to five clocks in mobile PC systems and desktop PC systems. The
MM74HC14 Hex Inverting Schmitt Trigger
MM74HC14 Hex Inverting Schmitt Trigger Features Typical propagation delay: 13ns Wide power supply range: 2V 6V Low quiescent current: 20µA maximum (74HC Series) Low input current: 1µA maximum Fanout of
MM74HC04 Hex Inverter
MM74HC04 Hex Inverter Features Typical propagation delay: 8ns Fan out of 10 LS-TTL loads Quiescent power consumption: 10µW maximum at room temperature Low input current: 1µA maximum General Description
NB3N502/D. 14 MHz to 190 MHz PLL Clock Multiplier
4 MHz to 90 MHz PLL Clock Multiplier Description The NB3N502 is a clock multiplier device that generates a low jitter, TTL/CMOS level output clock which is a precise multiple of the external input reference
NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input
January 1996 Revised August 2004 NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input General Description The NC7S14 is a single high performance CMOS Inverter with Schmitt Trigger input. The circuit
74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input
74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input Features I CC reduced by 50% Outputs source/sink 24mA 74ACT14 has TTL-compatible inputs Ordering Information Order Number General Description Package
Obsolete Product(s) - Obsolete Product(s)
HEX INVERTER (SINGLE STATE) HIGH SPEED: t PD = 5ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 10% V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
NC7S04 TinyLogic HS Inverter
NC7S04 TinyLogic HS Inverter General Description The NC7S04 is a single high performance CMOS Inverter. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation over a
Outputs Source/Sink 24 ma ACT157 Has TTL Compatible Inputs. Figure 1. Pinout: 16 Lead Packages Conductors (Top View) PIN NAME
The MC74AC157/74ACT157 is a high speed quad 2 input multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four outputs present the selected data
7WB Bit Bus Switch. The 7WB3126 is an advanced high speed low power 2 bit bus switch in ultra small footprints.
2-Bit Bus Switch The WB326 is an advanced high speed low power 2 bit bus switch in ultra small footprints. Features High Speed: t PD = 0.25 ns (Max) @ V CC = 4.5 V 3 Switch Connection Between 2 Ports Power
CD4099BC 8-Bit Addressable Latch
CD4099BC 8-Bit Addressable Latch General Description The CD4099BC is an 8-bit addressable latch with three address inputs (A0 A2), an active low enable input (E), active high clear input (CL), a data input
Low Power Hex TTL-to-ECL Translator
100324 Low Power Hex TTL-to-ECL Translator General Description The 100324 is a hex translator, designed to convert TTL logic levels to 100K ECL logic levels. The inputs are compatible with standard or
NC7ST00 TinyLogic HST 2-Input NAND Gate
TinyLogic HST 2-Input NAND Gate General Description The is a single 2-Input high performance CMOS NAND Gate, with TTL-compatible inputs. Advanced Silicon Gate CMOS fabrication assures high speed and low
UNISONIC TECHNOLOGIES CO., LTD CD4069
UNISONIC TECHNOLOGIES CO., LTD CD4069 INVERTER CIRCUITS DESCRIPTION The UTC CD4069 consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating
74AC00 74ACT00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description The AC/ACT00 contains four 2-input NAND gates. Ordering Code: Features I CC reduced by 50% Outputs source/sink 24 ma ACT00 has TTL-compatible inputs November
SN74LS122, SN74LS123. Retriggerable Monostable Multivibrators LOW POWER SCHOTTKY
Retriggerable Monostable Multivibrators These dc triggered multivibrators feature pulse width control by three methods. The basic pulse width is programmed by selection of external resistance and capacitance
MAC4DSM, MAC4DSN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
LM339S, LM2901S. Single Supply Quad Comparators
LM339S, LM290S Single Supply Quad Comparators These comparators are designed for use in level detection, low level sensing and memory applications in consumer and industrial electronic applications. Features
MC34064, MC33064, NCV33064
MC3464, MC3364, NCV3364 Undervoltage Sensing Circuit The MC3464 is an undervoltage sensing circuit specifically designed for use as a reset controller in microprocessorbased systems. It offers the designer
NCP4302 Secondary Side Synchronous Flyback Controller
Secondary Side Synchronous Flyback Controller The NCP4302 is a full featured controller and driver that provide all the control and protection functions necessary for implementing a synchronous rectifier
TC4011BP,TC4011BF,TC4011BFN,TC4011BFT
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4011BP/BF/BFN/BFT TC4011BP,TC4011BF,TC4011BFN,TC4011BFT TC4011B Quad 2 Input NAND Gate The TC4011B is 2-input positive logic NAND gate respectively.
M74HCT02TTR QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE HIGH SPEED: t PD = 15 ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V IL = 0.8V (MAX) BALANCED PROPAGATION