Quad Single Supply Comparator
|
|
- Calvin Owen Matthews
- 5 years ago
- Views:
Transcription
1 TECNICAL DATA Quad Single Supply Comparator IL339 The IL339 consists of four independent precision voltage comparators with an offset voltage specification as low as 2.0 m max for four comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators; wide range CO; MOS clock timers; multivibrators and high voltage digital logic gates. Single or Split Supply Operation Low Input Bias Current Low Input Offset Current Input Common Mode oltage Range to nd Low Output Saturation oltage TTL and CMOS Compatible ORDERIN INFORMATION IL339N Plastic IL339D SOIC T A = -40 to 85 C for all packages. LOIC DIARAM PIN ASSINMENT PIN 3 = CC PIN 12 = ND
2 MAXIMUM RATINS * Symbol Parameter alue Unit CC Power Supply oltages Single Supply Split Supplies IDR Input Differential oltage Range 36 ICR Input Common Mode oltage Range (1) -0.3 to CC I SC Output Short Circuit to round Continuous I IN Input Current, per pin (2) 50 ma T J Junction Temperature Plastic Packages 150 C Tstg Storage Temperature -65 to +150 C T L Lead Temperature, 1mm from Case for 10 Seconds 260 C P D Power A =25 C Plastic Package Derate above 25 C W mw/ C * Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Functional operation should be restricted to the Recommended Operating Conditions. Notes: 1. Split Power Supplies. 2. IN <-0.3. This input current will only exist when voltage at any of the input leads is driven negative. RECOMMENDED OPERATIN CONDITIONS Symbol Parameter Min Max Unit CC DC Supply oltage 2.5 or or 30 T A Operating Temperature, All Package Types C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. owever, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, IN and OUT should be constrained to the range ND ( IN or OUT ) CC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either ND or CC ). Unused outputs must be left open.
3 DC ELECTRICAL CARACTERISTICS (T A =-40 to +85 C) uaranteed Limit Symbol Parameter Test Conditions Min Typ Max Unit IO Input Offset oltage 0 =1.4 CC =5.0-30;R S 100 ICR =0 - ( CC -1.5) I IB Input Bias Current 0 =1.4 CC = ICR =0 - ( CC -1.5) I IO Input Offset Current 0 =1.4 CC = ICR =0 - ( CC -1.5) ICR Input Common Mode oltage Range I CC Supply Current R L =, CC = * m na na CC = CC R L =, CC =30 A OL oltage ain CC =15, R L =15K - 200* - /m t 1 Large Signal Response Time IN =TTL Logic Swing, ref =1.4, CC =5.0, R L =5.1K, RL =5.0 t 2 Response Time CC =5.0, R L =5.1K, RL =5.0 I sink Output Sink Current I (-)=1.0, I (+)=0, 0 1.5, CC =5.0 sat Saturation oltage I (-)=1.0, I (+)=0, I sink 4.0mA, CC =5.0 I OL Output Leakage Current I (+)=1.0, I (-)=0, 0 =5.0 0 = * 2.5* ma - 300* - ns - 1.3* - s 6.0* - - ma m 0.1* 1000 na IDR Differential Input oltage Range All IN ND or -Supply (if used) CC * *=@25 C
4 TYPICAL PERFORMANCE CARACTERISTICS ( CC =1.5, T A =+25 C, (each comporator)) Figure 1. Normalized Input Offset oltage Figure 2. Input Bias Current Figure 3. Output Sink Current versus Output Saturation oltage
5 N SUFFIX PLASTIC DIP (MS - 001AA) NOTES: 14 1 A F 0.25 (0.010) M T 1. Dimensions A, B do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. 8 7 D N B -T- SEATIN 5.27 PLANE K D M J F J (0.010) M T C M NOTES: K Dimensions A and B do not include mold flash or protrusion. M Maximum mold flash or protrusion 0.15 mm (0.006) per side P for A; for B 0.25 mm (0.010) per side. R C -T- K SEATIN PLANE M L J Dimension, mm Symbol MIN MAX A B C 5.33 D F J 0 10 K L M N 0.38 D SUFFIX SOIC (MS - 012AB) 14 1 A 8 7 B P C Symbol MIN MAX A B C D F R x 45 Dimension, mm 1.27
Low Power Low Offset Voltage Dual Comparators
TECNICAL DATA Low Power Low Offset oltage Dual Comparators IL2903 The IL2903 consists of two independent precision voltage comparators with an offset voltage specification as low as 2.0 m max for two comparators
More informationLow Power Quad Operational Amplifier
TECNICAL DATA Low Power Quad Operational Amplifier IL324 The IL324 contains four independent high gain operational amplifiers with internal frequency compensation. The four op-amps operate over a wide
More informationLow Power Dual Operational Amplifier
TECNICAL DATA Low Power Dual Operational Amplifier IL38 The IL38 contains two independent high gain operational amplifiers with internal frequency compensation. The two op-amps operate over a wide voltage
More informationIL386. Low Voltage Audio Power AMP TECHNICAL DATA
TECNICAL DATA Low Voltage Audio Power AMP IL386 The IL386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but
More informationQuad 2-Input Data Selectors/Multiplexer
TECNICAL DATA IN74C157A Quad 2-Input Data Selectors/Multiplexer The IN74C157A is identical in pin out to the LS/ALS157. The device inputs are compatible with standard CMOS outputs; with pull up resistors,
More informationQuad 2-Input Data Selector/Multiplexer with 3-State Outputs High-Performance Silicon-Gate CMOS
TECNICAL DATA IN74C257A Quad 2-Input Data Selector/Multiplexer with 3-State Outputs igh-performance Silicon-ate CMOS The IN74C257A is identical in pinout to the LS/ALS257. The device inputs are compatible
More informationLow Power Audio Amplifier
TECNICAL DATA Low Power Audio Amplifier IL34119 The IL34119 is a low power audio amplifier integrated circuit intended (primarily) for telephone applications, such as in speakerphones. It provides differential
More informationQuad 2-Input NAND Gate High-Voltage Silicon-Gate CMOS
TECHNICAL DATA Quad 2-Input NAND Gate High-oltage Silicon-Gate CMOS The NAND gates provide the system designer with direct emplementation of the NAND function. Operating oltage Range:.0 to 18 Maximum input
More informationMC14504B. Hex Level Shifter for TTL to CMOS or CMOS to CMOS
MCB Hex Level Shifter for TTL to CMOS or CMOS to CMOS The MCB is a hex noninverting level shifter using CMOS technology. The level shifter will shift a TTL signal to CMOS logic levels for any CMOS supply
More informationLM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
LM393, LM293, LM2903, LM2903V, NCV2903 Low Offset Voltage Dual Comparators The LM393 series are dual independent precision voltage comparators capable of single or split supply operation. These devices
More informationFeatures and Benefits
Low Power Quad Comparator SN339/P Semiconductor http:// www.auk.co.kr Description The SN339 consists of four independent voltage comparators designed to operate from a single power supply over a wide voltage
More informationLM339S, LM2901S. Single Supply Quad Comparators
LM339S, LM290S Single Supply Quad Comparators These comparators are designed for use in level detection, low level sensing and memory applications in consumer and industrial electronic applications. Features
More informationLM193A/293/A/393/A/2903 Low power dual voltage comparator
INTEGRATED CIRCUITS Supersedes data of 2002 Jan 22 2002 Jul 12 DESCRIPTION The LM193 series consists of two independent precision voltage comparators with an offset voltage specification as low as 2.0
More informationOctal 3-State Noninverting Transparent Latch High-Performance Silicon-Gate CMOS
TECHNICAL DATA IN74HCT573A Octal 3-State Noninverting Transparent Latch High-Performance Silicon-Gate CMOS The IN74HCT573A is identical in pinout to the LS/ALS573. This device may be used as a level converter
More informationQuad voltage comparator
AU9 DESCRIPTION The AU9 consists of four independent precision voltage comparators, with an offset voltage specification as low as.mv max for each comparator, which were designed specifically to operate
More informationUniversal Input Switchmode Controller
Universal Input Switchmode Controller Si9120 FEATURES 10- to 0- Input Range Current-Mode Control 12-mA Output Drive Internal Start-Up Circuit Internal Oscillator (1 MHz) and DESCRIPTION The Si9120 is a
More informationLM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators General Description The LM193 series consists of two independent precision voltage comparators with an offset voltage specification
More information8-BIT SERIAL-INPUT SHIFT REGISTER WITH LATCHED 3-STATE OUTPUTS High-Performance Silicon-Gate CMOS
8-BIT SERIAL-INPUT SHIFT REGISTER WITH LATCHED -STATE OUTPUTS High-Performance Silicon-Gate CMOS The IN74HC4094 is identical in pinout to the LS/ALS4094. The device inputs are compatible with standard
More informationLM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
Low Power Low Offset Voltage Dual Comparators General Description The LM193 series consists of two independent precision voltage comparators with an offset voltage specification as low as 2.0 mv max for
More informationPresettable 4-Bit Binary UP/DOWN Counter High-Speed Silicon-Gate CMOS
TECHNICAL DATA Presettable 4-Bit Binary UP/DOWN Counter High-Speed Silicon-Gate CMOS IN74ACT193 The IN74ACT193 is identical in pinout to the LS/ALS192, HC/HCT192. The IN74ACT193 may be used as a level
More informationOBSOLETE - PART DISCONTINUED
General Description The series consists of two independent precision voltage comparators with an offset voltage specification as low as 1mV. The input common mode voltage range of these comparators includes
More informationLM339, LM239, LM2901, LM2901V, NCV2901, MC3302. Single Supply Quad Comparators
LM339, LM239, LM290, LM290V, NCV290, MC3302 Single Supply Quad Comparators These comparators are designed for use in level detection, low level sensing and memory applications in consumer, automotive,
More informationOPERATIONAL AMPLIFIER & VOLTAGE REFERENCE KL103/A TECHNICAL DATA DESCRIPTION. PIN CONNECTIONS (top view) OPERATIONAL AMPLIFIER
TECHNICAL DATA OPERATIONAL AMPLIFIER & OLTAGE REFERENCE KL13/A OPERATIONAL AMPLIFIER LOW INPUT OFFSET OLTAGE :. typ. LOW SUPPLY CURRENT : 3 A/op. (@ cc = ) MEDIUM BANDWIDTH (unity gain) :.9MHz LARGE OUTPUT
More informationP SUFFIX CASE 646 Single Supply Split Supplies SO-14 D SUFFIX CASE 751A PIN CONNECTIONS
Dual Operational Amplifier and Dual Comparator The MC05 contains two differential-input operational amplifiers and two comparators, each set capable of single supply operation. This operational amplifier-comparator
More informationLM393, LM293, LM2903, LM2903V, NCV2903, NCV2903V. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293, NCV293V Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are
More informationLM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293 Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are designed
More informationLow Power Low Offset Voltage Dual Comparators
Low Power Low Offset Voltage Dual Comparators GENERAL DESCRIPTION The TS393 is dual independent precision voltage comparators capable of single-supply or split-supply operation. The specifications as low
More informationMM74HC86 Quad 2-Input Exclusive OR Gate
MM74HC86 Quad 2-Input Exclusive OR Gate Features Typical Propagation Delay: 9ns Wide Operating oltage Range: 2 6 Low Input Current: 1mA Maximum Low Quiescent Current: 20mA Max. (74 Series) Output Drive
More information8-Stage Static Bidirectional Parallel/ Serial Input/Output Bus Register High-Voltage Silicon-Gate CMOS
TECNICA DATA IW4034B 8-Stage Static Bidirectional Parallel/ Serial Input/Output Bus Register igh-voltage Silicon-Gate CMOS The IW4034B is a static eight-stage parallel-or serial-input paralleloutput register.
More informationAT7576 2A Step Down Voltage Regulator with Operational Amplifier
FEATURES DESCRIPTION Output oltage Range, 1.23 to 37 ±3% Guaranteed 2A Output Current Wide Input oltage Range, 40 52KHz Fixed Frequency Oscillator TTL Shutdown capability, Low Power Standby Mode High Efficiency
More informationPhase-Locked Loop High-Performance Silicon-Gate CMOS
TECHNICAL DATA Phase-Locked Loop High-Performance Silicon-Gate CMOS The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The IN74HC4046A
More informationLM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293 Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are designed
More information256K (32K x 8) Paged Parallel EEPROM AT28C256
Features Fast Read Access Time 150 ns Automatic Page Write Operation Internal Address and Data Latches for 64 Bytes Internal Control Timer Fast Write Cycle Times Page Write Cycle Time: 3 ms or 10 ms Maximum
More informationCD4538 Dual Precision Monostable
CD4538 Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
More informationMM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well as the capability
More informationDescription O FF G ATE C LK PT8A323 4/5/6/7. 1 NTC1 NTC1 I I NTC voltage input, NTC open detection input.
Features Description Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Direct drive SCR Auto Heating off after heating timer timeout Low
More informationMC3403, MC3303. Single Supply Quad Operational Amplifiers
MC0, MC0 Single Supply Quad Operational Amplifiers The MC0 is a low cost, quad operational amplifier with true differential inputs. The device has electrical characteristics similar to the popular MC7C.
More informationPT8A3270/1/2/3/4/5/6/7 Heating Controller
Features Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Proportional control Pulse trigger for high current SCR Internal Zener Auto Heating
More informationPresettable Up/Down Counter High-Voltage Silicon-Gate CMOS
TECNICA DATA IW029B Presettable Up/Down Counter igh-voltage Silicon-Gate CMOS The IW029B coists of a four-stage binary or BCD-decade up/down counter with provisio for look-ahead carry in both counting
More informationTS331 Low Power Low Offset Voltage Comparators
SOT-25 Pin Definition: 1. Input + 2. Ground 3. Input - 4. Output 5. Vcc General Description The TS331 is single precision voltage comparators capable of single-supply or split-supply operation. The specifications
More informationLOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS. Features
General Description The consist of two independent precision voltage comparators with a typical offset voltage of 1.0mV and high gain. They are specifically designed to operate from a single power supply
More informationAS339/339A. Description. Pin Assignments. Features. Applications LOW POWER LOW OFFSET VOLTAGE QUAD COMPARATORS AS339/339A
LOW POWER LOW OFFSET VOLTAGE QUAD COMPARATORS Description Pin Assignments The consist of four independent precision voltage comparators with a typical offset voltage of 2.0mV and high gain. They are specifically
More informationLP265 LP365 Micropower Programmable Quad Comparator
LP265 LP365 Micropower Programmable Quad Comparator General Description The LP365 consists of four independent voltage comparators The comparators can be programmed four at the same time for various supply
More informationILX485. Low-Power, RS-485/RS-422 Transceivers TECHNICAL DATA
TECHNICAL DATA Low-Power, RS-485/RS-422 Transceivers ILX485 Description The ILX485 is low-power transceivers for RS-485 and RS- 422 communication. IC contains one driver and one receiver. The driver slew
More informationO FF G ATE C LK PT8A324 4/5/6/7. 1 NTC1 NTC1 I I NTC voltage input, NTC open detection input.
Features Description Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Direct drive SCR Auto Heating off after heating timer timeout Low
More informationMM74HC00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description The MM74HC00 NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
More informationMM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The MM74HC132 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well
More informationPresettable 4-Bit Binary UP/DOWN Counter High-Speed Silicon-Gate CMOS
TECHNICAL DATA Presettable 4-Bit Binary UP/DOWN Counter High-Speed Silicon-Gate CMOS IN74AC193 The IN74AC193 is identical in pinout to the LS/ALS193, HC/HCT193. The device inputs are compatible with standard
More informationIR2122(S) CURRENT SENSING SINGLE CHANNEL DRIVER
Preliminary Data Sheet No. PD60130-K CURRENT SENSING SINGLE CHANNEL DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt
More informationLM392/LM2924 Low Power Operational Amplifier/Voltage Comparator
LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated
More informationPI5V330S. Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux. Features. Description. Block Diagram. Pin Configuration.
Features High-performance solution to switch between video sources Wide bandwidth: 570 MHz (typical) Low On-Resistance: 5Ω (typical) Low crosstalk at 10 MHz: 80dB Ultra-low quiescent power (0.1µA typical)
More informationDS Tap High Speed Silicon Delay Line
www.dalsemi.com FEATURES All-silicon timing circuit Five delayed clock phases per input Precise tap-to-tap nominal delay tolerances of ±0.75 and ±1 ns Input-to-tap 1 delay of 5 ns Nominal Delay tolerances
More informationMM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
More informationM74HC14. Hex Schmitt inverter. Features. Description
Hex Schmitt inverter Features High speed: t PD =12 ns (typ.) at CC = 6 Low power dissipation: I CC = 1 μa (max.) at T A =25 C High noise immunity: H = 1.2 (typ.) at CC = 6 Symmetrical output impedance:
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION PDIP 8 N SUFFIX CASE 626 LM311D AWL YYWW SO 8 98 Units/Rail
The ability to operate from a single power supply of 5.0 V to 30 V or 15 V split supplies, as commonly used with operational amplifiers, makes the LM211/LM311 a truly versatile comparator. Moreover, the
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM392 Low Power Operational Amplifier/Voltage Comparator General Description
More informationDS3486 Quad RS-422, RS-423 Line Receiver
Quad RS-422, RS-423 Line Receiver General Description National s quad RS-422, RS-423 receiver features four independent receivers which comply with EIA Standards for the electrical characteristics of balanced/unbalanced
More information4-megabit (512K x 8) Single 2.7-volt Battery-Voltage Flash Memory AT29BV040A
Features Single Supply Voltage, Range 2.7V to 3.6V Single Supply for Read and Write Software Protected Programming Fast Read Access Time 200 ns Low Power Dissipation 15 ma Active Current 50 µa CMOS Standby
More informationNOT RECOMMENDED FOR NEW DESIGN. Application
Description Pin Assignments The consists of two independent precision voltage comparators with an offset voltage specification as low as 2.mV max for two comparators which were designed specifically to
More informationMC33201, MC33202, MC33204, NCV33202, NCV33204
MC3320, MC33202, MC33204, NCV33202, NCV33204 Low Voltage, RailtoRail Operational Amplifiers The MC3320/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The
More informationAutomotive Wash Wiper Timer
TECNICAL DATA Automotive Wash Wiper Timer IL33197A The IL33197A is a standard wiper timer control device designed for harsh automotive applications. The device can perform the intermittent, after wash,
More informationM74HCT04. Hex inverter. Features. Description
Hex inverter Features High speed: t PD = 11 ns (typ.) at =4.5V Low power dissipation: I CC = 1 μa (max.) at T A =25 C Compatible with TTL outputs: V IH = 2 V (min.) V IL = 0.8 V (max) Balanced propagation
More informationLM392 LM2924 Low Power Operational Amplifier Voltage Comparator
LM392 LM2924 Low Power Operational Amplifier Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits One is a high gain internally frequency compensated
More informationHIGH-VOLTAGE HIGH-CURRENT DARLINGTON TRANSISTOR ARRAYS ILN2004 TECHNICAL DATA LOGIC SYMBOL LOGIC DIAGRAM
TECHNICAL DATA HIGH-VOLTAGE HIGH-CURRENT DARLINGTON TRANSISTOR ARRAYS ILN2004 The ILN2004 are monolithic high-voltage, high-current Darlington transistor arrays. Each consists of seven n-p-n Darlington
More informationMC33272A, MC33274A, NCV33272A, NCV33274A. Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers
MC33272A, MC3327A, NCV33272A, NCV3327A Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers The MC33272/7 series of monolithic operational amplifiers are quality fabricated with
More informationAnalog Multiplexer Demultiplexer High-Performance Silicon-Gate CMOS
TECHNICAL DATA Analog Multiplexer Demultiplexer High-erformance Silicon-Gate CMOS The utilize silicon-gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF leakage currents.
More information8-Bit Bidirectional Universal Shift Register with Parallel I/O High-Speed Silicon-Gate CMOS
TECHNICAL ATA IN74ACT299 8-Bit Bidirectional Universal Shift Register with Parallel I/O High-Speed Silicon-Gate CMOS The IN74ACT299 is identical in pinout to the LS/ALS299, HC/HCT299. The IN74ACT299 may
More informationUniversal Input Switchmode Controller
End of Life. Last Available Purchase Date is 31-Dec-2014 Si9120 Universal Input Switchmode Controller FEATURES 10- to 450-V Input Range Current-Mode Control 125-mA Output Drive Internal Start-Up Circuit
More informationKA239, LM339/A (KA339/A), LM2901 (KA2901), KA3302
QUAD DIFFERENTIAL COMPARATOR The LM/KA239 series consists of four independent voltage comparators designed to operate from single power supply over a wide voltage range. FEATURES Single or dual supply
More informationDS3486 Quad RS-422, RS-423 Line Receiver
DS3486 Quad RS-422, RS-423 Line Receiver General Description National s quad RS-422, RS-423 receiver features four independent receivers which comply with EIA Standards for the electrical characteristics
More informationCD4538BC Dual Precision Monostable
CD4538BC Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
More informationPI90LV031A PI90LV027A PI90LV017A. 3V LVDS High-Speed Differential Line Drivers. Description. Features PI90LV027A PI90LV031A PI90LV017A
PI90LV03A PI90LV027A PI90LV07A 3V LVDS High-Speed Differential Line Drivers Features Signaling Rates >400Mbps (200 MHz) Single 3.3V Power Supply Design ±30mV Differential Swing Maximum Differential Skew
More informationMC14001B Series. B Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series B Suffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
More informationVoltage comparator PIN CONFIGURATIONS FEATURES BLOCK DIAGRAM APPLICATIONS ORDERING INFORMATION. D, N Packages
DESCRIPTION The is a high-speed analog voltage comparator which, for the first time, mates state-of-the-art Schottky diode technology with the conventional linear process. This allows simultaneous fabrication
More information. HIGH MAXIMUM ASTABLE FREQUENCY 2.7MHz PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR NE555
TS555C,I,M LOW POWER SINGLE CMOS TIMERS. ERY LOW POWER CONSUMPTION : 100µA typ at CC = 5. HIGH MAXIMUM ASTABLE FREQUENCY 2.7MHz PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR NE555. OLTAGE RANGE :
More informationIX2127NTR. High-Voltage Power MOSFET & IGBT Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features.
High-Voltage Power MOSFET & IGBT Driver Driver Characteristics Parameter Rating Units V OFFSET 6 V I O +/- (Source/Sink) 25/5 ma V th 25 mv t ON / t OFF (Typical) 1 ns Features Floating Channel Designed
More informationTS358/TS2904 Single Supply Dual Operational Amplifiers
SOP-8 DIP-8 Pin assignment: 1. Output A 8. cc 2. Input A (-) 7. Output B 3. Input A (+) 6. Input B (-) 4. Gnd 5. Input B (+) General Description Utilizing the circuit designs perfected for recently introduced
More informationSingle/Dual/Quad High-Speed, Ultra Low-Power, Single-Supply TTL Comparators
19-129; Rev. 3; 7/94 Single/Dual/Quad High-Speed, Ultra Low-Power, General Description The MAX97/MAX98/MAX99 dual, quad, and single high-speed, ultra low-power voltage comparators are designed for use
More informationAdaptive Power MOSFET Driver 1
Adaptive Power MOSFET Driver 1 FEATURES dv/dt and di/dt Control Undervoltage Protection Short-Circuit Protection t rr Shoot-Through Current Limiting Low Quiescent Current CMOS Compatible Inputs Compatible
More informationDual Voltage Comparator
AVAILABLE AS MILITARY SPECIFICATIONS M38510/10305B MIL-STD-883, 1.2.1 FEATURES Wide operating supply range: ±15V to a single +5V Low input current: 6 na High sensitivity: 10μV Wide differential input range:
More informationQS54/74FCT373T, 2373T. High-Speed CMOS Bus Interface 8-Bit Latches MDSL QUALITY SEMICONDUCTOR, INC. 1 DECEMBER 28, 1998
Q QUALITY SEMICONDUCTOR, INC. QS54/74FCT373T, 2373T High-Speed CMOS Bus Interface 8-Bit Latches QS54/74FCT373T QS54/74FCT2373T FEATURES/BENEFITS Pin and function compatible to the 74F373 74FCT373 and 74ABT373
More informationPJ324CS. Quad Low Power Operational Amplifiers FEATURES ORDERING INFORMATION. MAXIMUM RATING(Ta=+25,unless otherwise noted.)
T he series are lowcost, quad operational amplifiers with true differential inputs. These have several distinct advantage over standard operational amplifier types in single supply applications. The quad
More informationTPS2010A, TPS2011A, TPS2012A, TPS2013A POWER-DISTRIBUTION SWITCHES
33-mΩ (5-V Input) High-Side MOSFET Switch Short-Circuit and Thermal Protection Operating Range... 2.7 V to 5.5 V Logic-Level Enable Input Typical Rise Time... 6.1 ms Undervoltage Lockout Maximum Standby
More informationHIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H GENERAL DESCRIPTION FEATURES ORDERING INFORMATION
HIGH FREQUENCY DC-TO-DC EALUATION KIT AAILABLE HIGH FREQUENCY DC-TO-DC FEATURES Pin Compatible with, High Frequency Performance DC-to-DC Converter Low Cost, Two Low alue External Capacitors Required...
More informationOutput. Single Supply. Output. Input polarity is reversed when GND pin is used as an output. Load Referred to Negative Supply. Output.
Single Comparators The ability to operate from a single power supply of. V to V or V split supplies, as commonly used with operational amplifiers, makes the LM/LM a truly versatile comparator. Moreover,
More information74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input
74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input Features I CC reduced by 50% Outputs source/sink 24mA 74ACT14 has TTL-compatible inputs Ordering Information Order Number General Description Package
More informationNot Recommended for New Designs
Not Recommended for New Designs The MAX99 was manufactured for Maxim by an outside wafer foundry using a process that is no longer available. It is not recommended for new designs. A Maxim replacement
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationFeatures V DD 4 STROBE MOS. Bipolar. Sub 8 GND V EE OUT 8
8-Bit Serial-Input Latched Drivers Final Information General Description BiCMOS technology gives the family flexibility beyond the reach of standard logic buffers and power driver arrays. These devices
More informationQuad 7 ns Single Supply Comparator AD8564
Quad 7 ns Single Supply Comparator AD8564 FEATURES 5 V single-supply operation 7 ns propagation delay Low power Separate input and output sections TTL/CMOS logic-compatible outputs Wide output swing TSSOP,
More informationLow Power Low Offset Voltage Single Comparator
Low Power Low Offset Voltage Single Comparator Product Description The consists of a independent precision voltage comparator which was designed specifically to operate from a single power supply over
More informationFST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
More informationA6833. DABiC-5 32-Bit Serial Input Latched Sink Drivers
DABiC-5 32-Bit Serial Input Latched Sink Drivers Features and Benefits 3.3 to 5 V logic supply range To 10 MHz data input rate 30 V minimum output breakdown Darlington current-sink outputs Low-power CMOS
More informationIL8190 TECHNICAL DATA PRECISION AIR - CORE TACH / SPEEDO DRIVER WITH RETURN TO ZERO DESCRIPTION FEATURES
TECHNICAL DATA PRECISION AIR - CORE TACH / SPEEDO DRIVER WITH RETURN TO ZERO IL8190 DESCRIPTION The IL8190 is specifically designed for use with air core meter movements. The IC provides all the functions
More informationLM2901 LOW POWER QUAD VOLTAGE COMPARATORS. WIDE SINGLE SUPPLY VOLTAGE RANGE OR.
LOW POWER QUAD OLTAGE COMPARATORS. WIDE SINGLE SUPPLY OLTAGE RANGE OR. DUAL SUPPLIES FOR ALL DEICES : +2 TO +36 OR ± TO ±8 ERY LOW SUPPLY CURRENT (.ma) INDEPENDENT OF SUPPLY OLTAGE (.4mW/comparator at
More informationAutomotive Direction Indicator
TECNICAL DATA Automotive Direction Indicator IL3393-03 The IL3393-03 is a new generation industry standard UAA04 Flasher. It has been developed for enhanced EMI sensitivity, system reliability, and improved
More informationCA3262A, CA3262. Quad-Gated, Inverting Power Drivers. Features. Description. Ordering Information. Pinouts. August 1997
Semiconductor CA6A, CA6 August 997 Quad-Gated, Inverting Power Drivers Features Independent Over-Current Limiting On Each Output Independent Over-Temperature Limiting On Each Output Output Drivers Capable
More informationLow Power Low Offset Voltage Dual Comparators
Low Power Low Offset ltage Dual Comparators Product Description The GS393 consists of two independent precision voltage comparators which were designed specifically to operate from a single power supply
More informationCMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTER Microprocessor Compatible
CMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTER Microprocessor Compatible FEATURES FOUR-QUADRANT MULTIPLICATION LOW GAIN TC: 2ppm/ C typ MONOTONICITY GUARANTEED OVER TEMPERATURE SINGLE 5V TO 15V SUPPLY
More informationLow Power Hex ECL-to-TTL Translator
Low Power Hex ECL-to-TTL Translator General Description The 100325 is a hex translator for converting F100K logic levels to TTL logic levels. Differential inputs allow each circuit to be used as an inverting,
More information