74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input
|
|
|
- Agatha Atkinson
- 5 years ago
- Views:
Transcription
1 74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input Features I CC reduced by 50% Outputs source/sink 24mA 74ACT14 has TTL-compatible inputs Ordering Information Order Number General Description Package Number Package Description February 2011 The 74AC14 and 74ACT14 contain six inverter gates each with a Schmitt trigger input. They are capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. In addition, they have a greater noise margin than conventional inverters. The 74AC14 and 74ACT14 have hysteresis between the positive-going and negative-going input thresholds (typically 1.0V) which is determined internally by transistor ratios and is essentially insensitive to temperature and supply voltage variations. 74AC14SC M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow 74AC14SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74AC14MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 74ACT14SC M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow 74ACT14MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Device also available in Tape and Reel. Specify by appending suffix letter X to the ordering number. 74AC14, 74ACT14 Rev
2 Connection Diagram Pin Description I n O n Pin Names Description Inputs Outputs Logic Symbol Function Table Input A L H IEEE/IEC Output O H L 74AC14, 74ACT14 Rev
3 Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Rating V CC Supply Voltage 0.5V to +7.0V I IK DC Input Diode Current V I 0.5V 20mA V I V CC mA V I DC Input Voltage 0.5V to V CC + 1.5V I OK DC Output Diode Current V O 0.5V 20mA V O V CC + 0.5V +20mA V O DC Output Voltage 0.5V to V CC + 0.5V I O DC Output Source or Sink Current ±50mA I CC or I GND DC V CC or Ground Current per Output Pin ±50mA T STG Storage Temperature 65 C to +150 C T J Junction Temperature 140 C Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter Rating V CC Supply Voltage AC 2.0V to 6.0V ACT 4.5V to 5.5V V I Input Voltage 0V to V CC V O Output Voltage 0V to V CC T A Operating Temperature 40 C to +85 C 74AC14, 74ACT14 Rev
4 DC Electrical Characteristics for AC Symbol V OH V OL I IN (3) V t+ Parameter Minimum HIGH Level Output Voltage Maximum LOW Level Output Voltage Maximum Input Leakage Current Maximum Positive Threshold V CC T A +25 C T A 40 C to +85 C (V) Conditions Typ Guaranteed Limits Notes: 1. All outputs loaded; thresholds on input associated with output under test. 2. Maximum test duration 2.0ms, one output loaded at a time. 3. I IN and I 3.0V are guaranteed to be less than or equal to the respective 5.5V V CC. Units 3.0 I OUT 50µA V I OH 12mA I OH 24mA I OH 24mA (1) I OUT 50µA V I OL 12mA I OL 24mA I OL 24mA (1) V I V CC, GND ±0.1 ±1.0 µa 3.0 T A Worst Case V V t Minimum Negative 3.0 T A Worst Case V Threshold V H(MAX) Maximum Hysteresis 3.0 T A Worst Case V V H(MIN) Minimum Hysteresis 3.0 T A Worst Case V I OLD Minimum Dynamic 5.5 V OLD 1.65V Max. 75 ma I OHD Output Current (2) 5.5 V OHD 3.85V Min. 75 ma (3) I CC Maximum Quiescent Supply Current 5.5 V IN V CC or GND µa 74AC14, 74ACT14 Rev
5 DC Electrical Characteristics for ACT Symbol V IH V IL V OH V OL Parameter Minimum HIGH Level Input Voltage Maximum LOW Level Input Voltage Minimum HIGH Level Output Voltage Maximum LOW Level Output Voltage V CC (V) Conditions T A +25 C Typ. Notes: 4. All outputs loaded; thresholds on input associated with output under test. 5. Maximum test duration 2.0ms, one output loaded at a time. T A 40 C to +85 C Guaranteed Limits Units 4.5 V OUT 0.1V or V 5.5 V CC 0.1V V OUT 0.1V or V 5.5 V CC 0.1V I OUT 50µA V V IN V IL or V IH, I OH 24mA V IN V IL or V IH, I OH 24mA (4) I OUT 50µA V V IN V IL or V IH, I OL 24mA V IN V IL or V IH, I OL 24mA (4) I IN Maximum Input 5.5 V I V CC, GND ±0.1 ±1.0 µa Leakage Current V H(MAX) Maximum Hysteresis 4.5 T A Worst Case V V H(MIN) Minimum Hysteresis 4.5 T A Worst Case V V t+ Maximum Positive 4.5 T A Worst Case V Threshold V t Minimum Negative 4.5 T A Worst Case V Threshold I CCT Maximum I CC /Input 5.5 V I V CC 2.1V ma I OLD Minimum Dynamic 5.5 V OLD 1.65V Max. 75 ma I OHD Output Current (5) 5.5 V OHD 3.85V Min. 75 ma I CC Maximum Quiescent Supply Current 5.5 V IN V CC or GND µa 74AC14, 74ACT14 Rev
6 AC Electrical Characteristics for AC Symbol Parameter V CC (V) (6) Note: 6. Voltage range 3.3 is 3.3V ± 0.3V. Voltage range 5.0 is 5.0V ± 0.5V. AC Electrical Characteristics for ACT Note: 7. Voltage Range 5.0 is 5.0V ± 0.5V. Capacitance T A +25 C, C L 50pF T A 40 C to +85 C, C L 50pF Min. Typ. Max. Min. Max. t PLH Propagation Delay ns t PHL Propagation Delay ns Symbol Parameter V CC (V) (7) T A +25 C, C L 50pF T A 40 C to +85 C, C L 50pF Min. Typ. Max. Min. Max. Units t PLH Propagation Delay ns t PHL Propagation Delay ns Symbol Parameter Conditions Typ Units C IN Input Capacitance V CC OPEN 4.5 pf C PD Power Dissipation Capacitance V CC 5.0V AC 25.0 pf ACT 80 Units 74AC14, 74ACT14 Rev
7 Physical Dimensions 6.00 PIN ONE INDICATOR 1.75 MAX (0.33) A M B C B A C 0.10 C LAND PATTERN RECOMMENDATION SEE DETAIL A R0.10 R X 45 GAGE PLANE 0.36 NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE CONFORMS TO JEDEC MS-012, VARIATION AB, ISSUE C, B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE MOLD FLASH OR BURRS. D) LANDPATTERN STANDARD: SOIC127P600X145-14M E) DRAWING CONFORMS TO ASME Y14.5M-1994 F) DRAWING FILE NAME: M14AREV (1.04) DETAIL A SCALE: 20:1 SEATING PLANE Figure Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor s online packaging area for the most recent package drawings: 74AC14, 74ACT14 Rev
8 Physical Dimensions (Continued) Figure Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor s online packaging area for the most recent package drawings: 74AC14, 74ACT14 Rev
9 Physical Dimensions (Continued) 0.43 TYP R0.09 min TOP & BOTTOM A. CONFORMS TO JEDEC REGISTRATION MO-153, VARIATION AB, REF NOTE 6 B. DIMENSIONS ARE IN MILLIMETERS C. DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSIONS D. DIMENSIONING AND TOLERANCES PER ANSI Y14.5M, 1982 E. LANDPATTERN STANDARD: SOP65P640X110-14M F. DRAWING FILE NAME: MTC14REV R0.09min Figure Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor s online packaging area for the most recent package drawings: 74AC14, 74ACT14 Rev
10 74AC14, 74ACT14 Rev
74AC10, 74ACT10 Triple 3-Input NAND Gate
74AC10, 74ACT10 Triple 3-Input NAND Gate Features I CC reduced by 50% on 74AC only Outputs source/sink 24mA Ordering Information Order Number Package Number General Description January 2008 The AC/ACT10
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
MM74HC86 Quad 2-Input Exclusive OR Gate
MM74HC86 Quad 2-Input Exclusive OR Gate Features Typical Propagation Delay: 9ns Wide Operating oltage Range: 2 6 Low Input Current: 1mA Maximum Low Quiescent Current: 20mA Max. (74 Series) Output Drive
74AC20 Dual 4-Input NAND Gate
74AC20 Dual 4-Input NAND Gate Features I CC reduced by 50% Outputs source/sink 24mA General Description The AC20 contains four, 4-input NAND gates. January 2008 Ordering Information Order Number Package
74AC04 74ACT04 Hex Inverter
74AC04 74ACT04 Hex Inverter General Description The AC/ACT04 contains six inverters. Ordering Code: Features I CC reduced by 50% on 74AC only Outputs source/sink 24 ma ACT04 has TTL-compatible inputs November
FST Bit Bus Switch
Features 4Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description March 2008 Fairchild
74LVX14 Low Voltage Hex Inverter with Schmitt Trigger Input
74LVX14 Low Voltage Hex Inverter with Schmitt Trigger Input Features Input voltage level translation from 5V to 3V Ideal for low power/low noise 3.3V applications Guaranteed simultaneous switching noise
74AC00 74ACT00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description The AC/ACT00 contains four 2-input NAND gates. Ordering Code: Features I CC reduced by 50% Outputs source/sink 24 ma ACT00 has TTL-compatible inputs November
74VHC14 Hex Schmitt Inverter
74VHC14 Hex Schmitt Inverter Features High Speed: t PD = 5.5ns (typ.) at V CC = 5V Low power dissipation: I CC = 2µA (max.) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (min.) Power down
74AC273, 74ACT273 Octal D-Type Flip-Flop
74AC273, 74ACT273 Octal D-Type Flip-Flop Features Ideal buffer for microprocessor or memory Eight edge-triggered D-type flip-flops Buffered common clock Buffered, asynchronous master reset See 377 for
74AC541, 74ACT541 Octal Buffer/Line Driver with 3-STATE Outputs
74AC541, 74ACT541 Octal Buffer/Line Driver with 3-STATE Outputs Features I CC and I OZ reduced by 50% 3-STATE outputs Inputs and outputs opposite side of package, allowing easier interface to microprocessors
MM74HC08 Quad 2-Input AND Gate
MM74HC08 Quad 2-Input AND Gate Features Typical propagation delay: 7ns (t PHL ), 12ns (t PLH ) Fanout of 10 LS-TTL loads Quiescent power consumption: 2µA maximum at room temperature Low input current:
74AC573, 74ACT573 Octal Latch with 3-STATE Outputs
74AC573, 74ACT573 Octal Latch with 3-STATE Outputs Features I CC and I OZ reduced by 50% Inputs and outputs on opposite sides of package allowing easy interface with microprocessors Useful as input or
Package Description. Device also available in Tape and Reel except for N14A. Specify by appending suffix letter X to the ordering number.
MM74HC02 Quad 2-Input NOR Gate Features Typical propagation delay: 8ns Wide power supply range: 2V 6V Low quiescent supply current: 20µA maximum (74HC Series) Low input current: 1µA maximum High output
74AC373, 74ACT373 Octal Transparent Latch with 3-STATE Outputs
74AC373, 74ACT373 Octal Transparent Latch with 3-STATE Outputs Features I CC and I OZ reduced by 50% Eight latches in a single package 3-STATE outputs for bus interfacing Outputs source/sink 24mA ACT373
74VHCT00A Quad 2-Input NAND Gate
74VHCT00A Quad 2-Input NAND Gate Features High speed: t PD = 5.0ns (Typ.) at T A = 25 C High noise immunity: V IH = 2.0V, V IL = 0.8V Power down protection is provided on all inputs and outputs Low noise:
74AC244 74ACT244 Octal Buffer/Line Driver with 3-STATE Outputs
74AC244 74ACT244 Octal Buffer/Line Driver with 3-STATE Outputs General Description The AC/ACT244 is an octal buffer and line driver designed to be employed as a memory address driver, clock driver and
74AC175 74ACT175 Quad D-Type Flip-Flop
Quad D-Type Flip-Flop General Description The AC/ACT175 is a high-speed quad D-type flip-flop. The device is useful for general flip-flop requirements where clock and clear inputs are common. The information
MM74HCT08 Quad 2-Input AND Gate
MM74HCT08 Quad 2-Input AND Gate Features TTL, LS pin-out and threshold compatible Fast switching: t PLH, t PHL = 12ns (typ.) Low power: 10µW at DC High fan-out, 10 LS-TTL loads General Description March
74LCX14 Low Voltage Hex Inverter with 5V Tolerant Schmitt Trigger Inputs
74LCX14 Low Voltage Hex Inverter with 5V Tolerant Schmitt Trigger Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 6.5ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high
74VHC00 Quad 2-Input NAND Gate
74VHC00 Quad 2-Input NAND Gate Features High Speed: t PD = 3.7ns (typ.) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (min.) Power down protection is provided on all inputs Low noise: V OLP
74VHC27 Triple 3-Input NOR Gate
74VHC27 Triple 3-Input NOR Gate Features High speed: t PD = 4.1ns (typ) at T A = 25 C Low power dissipation: I CC = 2µA (max) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (min.) Power down
USB1T11A Universal Serial Bus Transceiver
Features Complies with Universal Serial Bus Specification 1.1 Utilizes Digital Inputs and Outputs to Transmit and Receive USB Cable Data Supports 12Mbit/s Full Speed and 1.5Mbit/s Low Speed Serial Data
MM74HCT05 Hex Inverter (Open Drain)
MM74HCT05 Hex Inverter (Open Drain) Features Open drain for wire-nor function LS-TTL pinout and threshold compatible Fanout of 10 LS-TTL loads Typical propagation delays: t PZL (with 1kΩ resistor) 10ns
MM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well as the capability
74AC74 74ACT74 Dual D-Type Positive Edge-Triggered Flip-Flop
74AC74 74ACT74 Dual D-Type Positive Edge-Triggered Flip-Flop General Description The AC/ACT74 is a dual D-type flip-flop with Asynchronous Clear and Set inputs and complementary (Q, Q) outputs. Information
74AC573 74ACT573 Octal Latch with 3-STATE Outputs
74AC573 74ACT573 Octal Latch with 3-STATE Outputs General Description The 74AC573 and 74ACT573 are high-speed octal latches with buffered common Latch Enable (LE) and buffered common Output Enable (OE)
74LVTH125 Low Voltage Quad Buffer with 3-STATE Outputs
74LVTH125 Low Voltage Quad Buffer with 3-STATE Outputs Features Input and output interface capability to systems at 5V V CC Bushold data inputs eliminate the need for external pull-up resistors to hold
74AC244 74ACT244 Octal Buffer/Line Driver with 3-STATE Outputs
Octal Buffer/Line Driver with 3-STATE Outputs General Description The AC/ACT244 is an octal buffer and line driver designed to be employed as a memory address driver, clock driver and bus-oriented tramitter/receiver
74AC299, 74ACT299 8-Input Universal Shift/Storage Register with Common Parallel I/O Pins
74AC299, 74ACT299 8-Input Universal Shift/Storage Register with Common Parallel I/O Pins Features I CC and I OZ reduced by 50% Common parallel I/O for reduced pin count Additional serial inputs and outputs
74AC251 74ACT251 8-Input Multiplexer with 3-STATE Output
74AC251 74ACT251 8-Input Multiplexer with 3-STATE Output General Description The AC/ACT251 is a high-speed 8-input digital multiplexer. It provides, in one package, the ability to select one bit of data
74AC257 74ACT257 Quad 2-Input Multiplexer with 3-STATE Outputs
74AC257 74ACT257 Quad 2-Input Multiplexer with 3-STATE Outputs General Description The AC/ACT257 is a quad 2-input multiplexer with 3- STATE outputs. Four bits of data from two sources can be selected
74AC574 74ACT574 Octal D-Type Flip-Flop with 3-STATE Outputs
Octal D-Type Flip-Flop with 3-STATE Outputs General Description The AC/ACT574 is a high-speed, low power octal flip-flop with a buffered common Clock (CP) and a buffered common Output Enable (OE). The
MM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
74LCX04 Low Voltage Hex Inverter with 5V Tolerant Inputs
74LCX04 Low Voltage Hex Inverter with 5V Tolerant Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 5.2ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high impedance inputs
74AC174 74ACT174 Hex D-Type Flip-Flop with Master Reset
74AC174 74ACT174 Hex D-Type Flip-Flop with Master Reset General Description The AC/ACT174 is a high-speed hex D-type flip-flop. The device is used primarily as a 6-bit edge-triggered storage register.
74AC245 74ACT245 Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs
74AC245 74ACT245 Octal Bidirectional Traceiver with 3-STATE Inputs/Outputs General Description The AC/ACT245 contai eight non-inverting bidirectional buffers with 3-STATE outputs and is intended for bus-oriented
MM74HC74A Dual D-Type Flip-Flop with Preset and Clear
MM74HC74A Dual D-Type Flip-Flop with Preset and Clear Features Typical propagation delay: 20ns Wide power supply range: 2V 6V Low quiescent current: 40µA maximum (74HC Series) Low input current: 1µA maximum
74ABT126 Quad Buffer with 3-STATE Outputs
74ABT126 Quad Buffer with 3-STATE Outputs Features Non-inverting buffers Output sink capability of 64mA, source capability of 32mA Guaranteed latchup protection High impedance glitch free bus loading during
USB1T20 Universal Serial Bus Transceiver
Features Complies with Universal Serial Bus Specification 2.0 for FS/LS Applications Utilizes Digital Inputs and Outputs to Transmit and Receive USB Cable Data Supports 12Mbit/s Full Speed (FS) and 1.5Mbit/s
74AC374 74ACT374 Octal D-Type Flip-Flop with 3-STATE Outputs
74AC374 74ACT374 Octal D-Type Flip-Flop with 3-STATE Outputs General Description The AC/ACT374 is a high-speed, low-power octal D-type flip-flop featuring separate D-type inputs for each flip-flop and
MM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The MM74HC132 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well
74AC574 74ACT574 Octal D-Type Flip-Flop with 3-STATE Outputs
Octal D-Type Flip-Flop with 3-STATE Outputs General Description The AC/ACT574 is a high-speed, low power octal flip-flop with a buffered common Clock (CP) and a buffered common Output Enable (OE). The
74AC299 74ACT299 8-Input Universal Shift/Storage Register with Common Parallel I/O Pins
8-Input Universal Shift/Storage Register with Common Parallel I/O Pi General Description The AC/ACT299 is an 8-bit universal shift/storage register with 3-STATE outputs. Four modes of operation are possible:
74AC821 74ACT Bit D-Type Flip-Flop with 3-STATE Outputs
74AC821 74ACT821 10-Bit D-Type Flip-Flop with 3-STATE Outputs General Description The AC/ACT821 is a 10-bit D-type flip-flop with 3-STATE outputs arranged in a broadside pinout. Ordering Code: Features
74ACT258 Quad 2-Input Multiplexer with 3-STATE Outputs
74ACT258 Quad 2-Input Multiplexer with 3-STATE Outputs Features I CC and I OZ reduced by 50% Multiplexer expansion by tying outputs together Inverting 3-STATE outputs Outputs source/sink 24mA TTL-compatible
MM74HC00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description The MM74HC00 NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates
NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates Features Ultra High Speed Capable of Implementing any Two-Input Logic Functions Typical Usage Replaces Two (2) TinyLogic Gate
74LCX14 Low Voltage Hex Inverter with 5V Tolerant Schmitt Trigger Inputs
74LCX14 Low Voltage Hex Inverter with 5V Tolerant Schmitt Trigger Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 6.5ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high
NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear
NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear Features Ultra-High Speed: t PD 2.6 (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Power
MM74HC4066 Quad Analog Switch
MM74HC4066 Quad Analog Switch Features Typical switch enable time: 15ns Wide analog input voltage range: 0V 12V Low ON resistance: 30 typ. (MM74HC4066) Low quiescent current: 80µA maximum (74HC) Matched
MM74HC14 Hex Inverting Schmitt Trigger
MM74HC14 Hex Inverting Schmitt Trigger Features Typical propagation delay: 13ns Wide power supply range: 2V 6V Low quiescent current: 20µA maximum (74HC Series) Low input current: 1µA maximum Fanout of
74F132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description Ordering Code: April 1988 Revised September 2000 The F132 contains four 2-input NAND gates which accept standard TTL input signals and provide standard
DM74LS14 Hex Inverter with Schmitt Trigger Inputs
Hex Inverter with Schmitt Trigger Inputs General Description This device contains six independent gates each of which performs the logic INVERT function. Each input has hysteresis which increases the noise
FST Bit Bus Switch
Features 4 Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description December 2012
74ALVC245 Low Voltage Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs
74ALVC245 Low Voltage Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs Features 1.65V to 3.6V V CC supply operation 3.6V tolerant inputs and outputs Power-off high impedance inputs and outputs
74LCX240 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs
74LCX240 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs Features 5V tolerant inputs and outputs 2.3V 3.6V V CC specifications provided 6.5ns t PD max. (V CC = 3.3V), 10µA I CC
74LVT573, 74LVTH573 Low Voltage Octal Transparent Latch with 3-STATE Outputs
January 2008 74LVT573, 74LVTH573 Low Voltage Octal Transparent Latch with 3-STATE Outputs Features Input and output interface capability to systems at 5V V CC Bushold data inputs eliminate the need for
74LVT245, 74LVTH245 Low Voltage Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs
February 2008 74LVT245, 74LVTH245 Low Voltage Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs Features Input and output interface capability to systems at 5V V CC Bushold data inputs eliminate
74LVT2245, 74LVTH2245 Low Voltage Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs and 25Ω Series Resistors in the B Port Outputs
January 2008 74LVT2245, 74LVTH2245 Low Voltage Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs and 25Ω Series Resistors in the B Port Outputs Features Input and output interface capability
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer Features Broad CC Operating Range: 1.65 to 5.5 Ultra High-Speed Power Down High-Impedance Inputs/Outputs Over-oltage Tolerance Inputs Facilitate
74LVX08 Low Voltage Quad 2-Input AND Gate
74LVX08 Low Voltage Quad 2-Input AND Gate Features Input Voltage Level Translation from 5 V to 3 V Ideal for Low-power / Low-Noise 3.3 V Applications Guaranteed Simultaneous Switching Noise Level and Dynamic
DM74LS132 Quad 2-Input NAND Gate with Schmitt Trigger Input
August 1986 Revised March 2000 DM74LS132 Quad 2-Input NAND Gate with Schmitt Trigger Input General Description This device contains four independent gates each of which performs the logic NAND function.
NC7WZ132 TinyLogic UHS Dual 2-Input NAND Gate with Schmitt Trigger Inputs
NC7WZ132 TinyLogic UHS Dual 2-Input NAND Gate with Schmitt Trigger Inputs Features Space saving US8 surface mount package MicroPak leadless package Ultra High Speed; t PD 3.1ns typ. into 50pF at 5V V CC
74LCX00 Low Voltage Quad 2-Input NAND Gate with 5V Tolerant Inputs
74LCX00 Low Voltage Quad 2-Input NAND Gate with 5V Tolerant Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 5.2ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high impedance
NC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input
January 2010 NC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input Features Ultra-High Speed: t PD 3.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65
74F32 Quad 2-Input OR Gate
74F32 Quad 2-Input OR Gate General Description This device contains four independent gates, each of which performs the logic OR function. Ordering Code: April 1988 Revised August 2000 74F32 Quad 2-Input
NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs)
April 2013 NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs) Features Ultra-High Speed: t PZL 2.3 ns (Typical) High I OL Output Drive: ±24 ma at 3 CC Broad CC Operating Range: 1.65 to 5.50 Power Down
MM74HC04 Hex Inverter
MM74HC04 Hex Inverter Features Typical propagation delay: 8ns Fan out of 10 LS-TTL loads Quiescent power consumption: 10µW maximum at room temperature Low input current: 1µA maximum General Description
FST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
FAN7391 High-Current, High & Low-Side, Gate-Drive IC
FAN7391 High-Current, High & Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 4.5 A / 4.5 A Sourcing / Sinking Current Driving Capability Common-Mode dv/dt Noise-Canceling
74VHC74 Dual D-Type Flip-Flop with Preset and Clear
74VHC74 Dual D-Type Flip-Flop with Preset and Clear Features High Speed: f MAX = 170MHz (typ.) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (min.) Power down protection is provided on all
74LCX07 Low Voltage Hex Buffer with Open Drain Outputs
74LCX07 Low Voltage Hex Buffer with Open Drain Outputs Features 5V tolerant inputs 2.3V to 5.5V V CC specifications provided 2.9ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high impedance inputs
NC7SV57 / NC7SV58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates
December 2010 NC7S57 / NC7S58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Extremely High Speed
74ACTQ74 Quiet Series Dual D-Type Positive Edge-Triggered Flip-Flop
74ACTQ74 Quiet Series Dual D-Type Positive Edge-Triggered Flip-Flop General Description The 74ACTQ74 is a dual D-type flip-flop with Asynchronous Clear and Set inputs and complementary (Q, Q) outputs.
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate Features Ultra-High Speed: t PD 2.9ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
74LCX74 Low Voltage Dual D-Type Positive Edge-Triggered Flip-Flop with 5V Tolerant Inputs
74LCX74 Low Voltage Dual D-Type Positive Edge-Triggered Flip-Flop with 5V Tolerant Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 7.0ns t PD max. (V CC = 3.3V), 10µA I CC max.
74F245 Octal Bidirectional Transceiver with 3-STATE Outputs
74F245 Octal Bidirectional Transceiver with 3-STATE Outputs Features Non-inverting buffers Bidirectional data path A outputs sink 24mA B outputs sink 64mA Ordering Information Order Number Package Number
74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs
74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs Features 5V tolerant inputs and outputs 2.3V 3.6V V CC specifications provided 6.0ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down
74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs
Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs General Description The LCX125 contains four independent non-inverting buffers with 3-STATE outputs. The inputs tolerate voltages up to 7V allowing
MM74HC Stage Binary Counter
MM74HC4040 12-Stage Binary Counter Features Typical propagation delay: 16ns Wide operating voltage range: 2 6V Low input current: 1µA Max. Low quiescent current: 80µA Max. (74HC Series) Output drive capability:
FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch
March 2008 FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch Features -40dB Off Isolation at 250MHz -40dB Non-adjacent Channel Crosstalk at 250MHz On Resistance: 4.5Ω Typical (RON) -3dB Bandwidth:
FAN7390 High-Current, High and Low Side, Gate-Drive IC
FAN739 High-Current, High and Low-Side, Gate-Drive IC Features! Floating Channels for Bootstrap Operation to +6V! Typically 4.5A/4.5A Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise
NC7SZ08 TinyLogic UHS Two-Input AND Gate
NC7SZ08 TinyLogic UHS Two-Input AND Gate Features Ultra-High Speed: t PD 2.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of
NC7WZ16 TinyLogic UHS Dual Buffer
NC7WZ16 TinyLogic UHS Dual Buffer Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX when
NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output)
NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output) Features 0.9V to 3.6V V CC Supply Operation 3.6V Over-Voltage Tolerant I/Os at VCC from 0.9V to 3.6V Extremely High Speed tpd - 1.0ns: Typical for 2.7V
FT3001 Reset Timer with Configurable Delay
FT3001 Reset Timer with Configurable Delay Features Delay Times: 3.0, 3.75, 4.5, 6.0 Seconds 1 µa I CC Current Consumption in Standby Primary and Secondary Input Reset Pins Push-Pull and Open-Drain Output
74ACTQ00 Quiet Series Quad 2-Input NAND Gate
74ACTQ00 Quiet Series Quad 2-Input NAND Gate Features I CC reduced by 50% Guaranteed simultaneous switching noise level and dynamic threshold performance Improved latch-up immunity Outputs source/sink
ISO-9001 AS9120certi cation ClassQ Military
Datasheet RochesterElectronics ManufacturedComponents Rochester branded components are manufactured using eitherdie/wafers purchasedfrom theoriginalsuppliers orrochesterwafers recreated from the originalip.
CD4069UBC Inverter Circuits
CD4069UBC Inverter Circuits General Description The CD4069UB consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating range, low power
74LCX541 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs
74LCX541 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs Features 5V tolerant input and outputs 2.3V 3.6V specifications provided 6.5ns t PD max ( = 3.3V), 10µA I CC max Power-down
NC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output January 2014 NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6 ns (Typical) into 50 pf at 5 CC High Output
74ALVC Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs
74ALVC162245 Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs General Description The ALVC162245 contains sixteen non-inverting
FAN7361, FAN7362 High-Side Gate Driver
FAN7361, FAN7362 High-Side Gate Driver Features! Floating Channel Designed for Bootstrap Operation to +600V! Typically 250mA/500mA Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling
NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch
September 2013 NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch Features Broad V CC Operating Range: 1.65 V to 5.5 V Rail-to-Rail Signal Handling Power Down High-Impedance Inputs/Outputs 5 Ω Switch
FAN73932 Half-Bridge Gate Drive IC
FAN73932 Half-Bridge Gate Drive IC Features Floating Channel for Bootstrap Operation to +600V Typically 2.5A/2.5A Sourcing/Sinking Current Driving Capability Extended Allowable Negative V S Swing to -9.8V
DM74ALS14 Hex Inverter with Schmitt Trigger Inputs
DM74ALS14 Hex Inverter with Schmitt Trigger Inputs General Description This device contains six independent gates, each of which performs the logic INVERT function. Each input has hysteresis which increases
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs General
NC7SZ00 TinyLogic UHS Two-Input NAND Gate
NC7SZ00 TinyLogic UHS Two-Input NAND Gate Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of