MC33201, MC33202, MC33204, NCV33202, NCV33204

Transcription

1 MC3320, MC33202, MC33204, NCV33202, NCV33204 Low Voltage, RailtoRail Operational Amplifiers The MC3320/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The inputs can be driven as high as 200 mv beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mv of each rail. This railtorail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (± 0.9 V) yet can operate with a supply of up to +2 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. Also, the combination of low noise and distortion with a high slew rate and drive capability make this an ideal amplifier for audio applications. Low Voltage, Single Supply Operation (+. V and Ground to +2 V and Ground) Input Voltage Range Includes both Supply Rails Output Voltage Swings within 50 mv of both Rails No Phase Reversal on the Output for Overdriven Input Signals High Output Current (I SC = 0 ma, Typ) Low Supply Current (I D = 0.9 ma, Typ) 600 Output Drive Capability Extended Operating Temperature Ranges (40 to +05 C and 55 to +25 C) Typical Gain Bandwidth Product = 2.2 MHz NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes PbFree Packages are Available PDIP P, VP SUFFIX CASE 626 SOIC D, VD SUFFIX CASE 75 Micro DM SUFFIX CASE 46A PDIP4 P, VP SUFFIX CASE 646 SOIC4 D, VD SUFFIX CASE 75A TSSOP4 DTB SUFFIX CASE 94G ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 0 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 2 of this data sheet. Semiconductor Components Industries, LLC, 2006 Publication Order Number: MC3320/D

2 MC3320, MC33202, MC33204, NCV33202, NCV33204 MAXIMUM RATINGS Rating Symbol Value Unit Supply Voltage (V CC to V EE ) V S +3 V Input Differential Voltage Range V IDR Note V Common Mode Input Voltage Range (Note 2) V CM V CC V to V EE 0.5 V Output Short Circuit Duration t s Note 3 sec Maximum Junction Temperature T J +50 C Storage Temperature T stg 65 to +50 C Maximum Power Dissipation P D Note 3 mw V DC ELECTRICAL CHARACTERISTICS (T A = 25 C) Characteristic V CC = 2.0 V V CC = 3.3 V V CC = 5.0 V Unit Input Offset Voltage V IO (max) MC3320 MC33202, NCV33202 MC33204, NCV33204 ±.0 ±0 ±2 ±.0 ±0 ±2 ± 6.0 ±.0 ±0 mv Output Voltage Swing V OH (R L = 0 k ) V OL (R L = 0 k ) Power Supply Current per Amplifier (I D ) Specifications at V CC = 3.3 V are guaranteed by the 2.0 V and 5.0 V tests. V EE = GND V min V max ma DC ELECTRICAL CHARACTERISTICS (V CC = V, V EE = Ground, T A = 25 C, unless otherwise noted.) Input Offset Voltage (V CM 0 V to 0.5 V, V CM.0 V to 5.0 V) MC3320: T A = + 25 C MC3320: T A = 40 to +05 C MC3320V: T A = 55 to +25 C MC33202: T A = + 25 C MC33202: T A = 40 to +05 C MC33202V: T A = 55 to +25 C NCV33202V: T A = 55 to +25 C (Note 4) MC33204: T A = + 25 C MC33204: T A = 40 to +05 C MC33204V: T A = 55 to +25 C NCV33204: T A = 55 to +25 C Input Offset Voltage Temperature Coefficient (R S = 50 ) T A = 40 to +05 C T A = 55 to +25 C Input Bias Current (V CM = 0 V to 0.5 V, V CM =.0 V to 5.0 V) T A = + 25 C T A = 40 to +05 C T A = 55 to +25 C 3 V IO 4 V IO / T 5, 6 I IB Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.. The differential input voltage of each amplifier is limited by two internal parallel backtoback diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The input common mode voltage range is limited by internal diodes connected from the inputs to both supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mv. 3. Power dissipation must be considered to ensure maximum junction temperature (T J ) is not exceeded. (See Figure 2) 4. NCV33202 and NCV33204 are qualified for automotive use mv V/ C na 3

3 MC3320, MC33202, MC33204, NCV33202, NCV33204 DC ELECTRICAL CHARACTERISTICS (cont.) (V CC = V, V EE = Ground, T A = 25 C, unless otherwise noted.) Input Offset Current (V CM = 0 V to 0.5 V, V CM =.0 V to 5.0 V) T A = + 25 C T A = 40 to +05 C T A = 55 to +25 C Common Mode Input Voltage Range V ICR V EE V CC V Large Signal Voltage Gain (V CC = V, V EE = 5.0 V) R L = 0 k Output Voltage Swing (V ID = ± 0.2 V) R L = 0 k R L = 0 k I IO 7 A VOL 50 25, 9, 0 Common Mode Rejection (V in = 0 V to 5.0 V) CMR db Power Supply Rejection Ratio V CC /V EE = 5.0 V/GND to 3.0 V/GND V OH V OL V OH V OL 2 PSRR Output Short Circuit Current (Source and Sink) 3, 4 I SC 50 0 ma na kv/v V V/V Power Supply Current per Amplifier (V O = 0 V) T A = 40 to +05 C T A = 55 to +25 C 5 I D ma AC ELECTRICAL CHARACTERISTICS (V CC = V, V EE = Ground, T A = 25 C, unless otherwise noted.) Slew Rate (V S = ± 2.5 V, V O = 2.0 V to V, R L = 2.0 k, A V = +.0) 6, 26 SR Gain Bandwidth Product (f = 00 khz) 7 GBW 2.2 MHz Gain Margin (, C L = 0 pf) 20, 2, 22 A M 2 db Phase Margin (, C L = 0 pf) 20, 2, 22 M 65 Deg Channel Separation (f =.0 Hz to 20 khz, A V = 00) 23 CS 90 db Power Bandwidth (V O = 4.0 V pp,, THD %) BW P 2 khz V/ s Total Harmonic Distortion (, V O =.0 V pp, A V =.0) f =.0 khz f = 0 khz 24 THD % Open Loop Output Impedance (V O = 0 V, f = 2.0 MHz, A V = 0) Z O 00 Differential Input Resistance (V CM = 0 V) R in 200 k Differential Input Capacitance (V CM = 0 V) C in.0 pf Equivalent Input Noise Voltage (R S = 00 ) f = 0 Hz f =.0 khz 25 e n nv/ Hz Equivalent Input Noise Current f = 0 Hz f =.0 khz 25 i n pa/ Hz 4

4 MC3320, MC33202, MC33204, NCV33202, NCV33204 ORDERING INFORMATION Operational Amplifier Function Device Operating Temperature Range Package Shipping MC3320D SOIC MC3320DG SOIC (PbFree) 9 Units / Rail MC3320DR2 SOIC Single MC3320DR2G MC3320P T A = 40 to +05 C SOIC (PbFree) PDIP MC3320PG PDIP (PbFree) MC3320VD SOIC MC3320VDG MC33202D T A = 55 to 25 C SOIC (PbFree) SOIC 9 Units / Rail MC33202DG SOIC (PbFree) MC33202DR2 SOIC MC33202DR2G MC33202DMR2 T A = 40 to +05 C SOIC (PbFree) Micro MC33202DMR2G Micro (PbFree) 4000 / Tape & Reel MC33202P PDIP Dual MC33202PG MC33202VD PDIP (PbFree) SOIC MC33202VDG SOIC (PbFree) 9 Units / Rail MC33202VDR2 SOIC MC33202VDR2G NCV33202VDR2* T A = 55 to 25 C SOIC (PbFree) SOIC NCV33202VDR2G* SOIC (PbFree) MC33202VP MC33202VPG PDIP PDIP (PbFree) For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD0/D. *NCV33202 and NCV33204 are qualified for automotive use. 0

5 MC3320, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS SOIC NB CASE 7507 ISSUE AH Y B X A 5 4 S 0.25 (0.00) M Y M K NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y4.5M, CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.5 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.27 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION THRU 7506 ARE OBSOLETE. NEW STANDARD IS Z H G D C 0.25 (0.00) M Z Y S X S SEATING PLANE 0.0 (0.004) N X 45 M J MILLIMETERS INCHES DIM MIN MAX MIN MAX A B C D G.27 BSC BSC H J K M 0 0 N S SOLDERING FOOTPRINT* SCALE 6: mm inches *For additional information on our PbFree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. 4