Labo K Effects

Transcription

1 Pwer Supply Kit fr NEVE 51/V3/VR SERIES Lab K Effects cntact@lab-k-effects.cm

2 cntents INTRODUCTION 3 KIT OVERVIEW 4 COMPOSITION DU KIT D A SSEMBLAGE ERREUR! SIGNET NON DEFINI. FPSU BOARD PARTS LIST 6 FPSU BOARD CONNECTOR PINOUT 6 CONNECTION OF THE POWER TRANSFORMER 6 VREG BOARD PARTS LIST 7 PSU BUS PINOUT 7 FPSU BOARD ASSEMBLY INTRUCTIONS 8 VREG BOARD ASSEMBLY INTRUCTIONS 8 FIXING FPSU AND VREG BOARDS 9 SCHEMATICS 10 Lab K Effects cntact@lab-k-effects.cm 2

3 intrductin This kit allws t built a pwer supply specifically designed fr Neve 51, V3 et VR legend Preamp and Equalizer mdules t put them in a rack. PSU bus system allws t cnnect up t 4 preamp/equalizer mdules pairs. Yu just have t build the adequate ribbn. The assembly kit secures the pcbs and radiatr f the PSU. The cmpact unit can be easily placed in the rack. Optinal accessry Lab K Effects Bus PSU adapter Allws t cnnect the psu t the bus via 5 cables (Stuffed r PCB nly) Lab K Effects cntact@lab-k-effects.cm 3

4 Kit verview 1 PCB (FPSU bard) fr cnnecting: 1 pwer transfrmer 2x15v 50VA (nt supplied) The +16V / -15V /-16V regulatin bard (VREG) This bard perfrms the rectificatin and filtering f ac pwer. It prvides the +48V phantm. 1 PCB (VREG bard) fr cnnecting: PSU Bus FPSU bard This bard prvides +16V / -16V /-15V regulated vltages! - Cnnectrs and cmpnents! The 2x15V 50VA pwer transfrmer is nt supplied Lab K Effects cntact@lab-k-effects.cm 4

5 Cmpsitin f the assembly kit! 1 steel base fr fixing: The FPSU card The +16V / -15V /-16V regulatin card (VREG) The heat sink! The fllwing elements: 4 M3x15 screws (A) 1 M3x5 screw (B) 4 plastic spacers (C) 3 50mm spacers (D) 2 Parker screws (E) 1 heat sink (F) 1 clip(g) 2 M3x15 screws (H) 2 washers (I) 7 M3 nuts (J) 3 insulatr pads fr TO220 (K) A B C D E F G H I J K Lab K Effects cntact@lab-k-effects.cm 5

6 FPSU bard parts list PL1 PCB cnnectr 25/4G Cnnectr 2 Nt fitted Replaced by 4 wires BR1 Rectifier D1, D2, D3, D4 1N4002 R1 180R R2 15K R3 12K C1, C2 4700µF/63v C3, C4 1000µF/100v C5, C7 100n100v C6, C8 47µF/63v IC 1 LM317HV All resistrs are 1/4w metal film 1% FPSU bard cnnectr pinut PL1 Cnnectr 2 1 Black 15V AC1 1 Red +22V 2 Brwn 15V AC1 2 Black 0V 3 red 15V AC2 3 Brwn -22V 4 Orange 15V AC2 4 Orange +48V Cnnectin f the pwer transfrmer Lab K Effects cntact@lab-k-effects.cm 6

7 Vreg bard parts list Cnnectr 1 3M D1 t D6 1N4002 R1, R2 0R R3, R5, R7 243R R6 2K7 R4, R8 2K7+200R serial cnnected C1, C2, C5, C6, C9, C10 100n/50v C3, C4, C7, C8, C11, C12 10µF/63v IC1, IC2 LM337T IC3 LM317T All resistrs are 1/4w metal film 1% Psu bus pinut 1 +48V 2 +48V 3 NC 4 0V 5 0V 6 0V 7 +16V 8 +16V 9 +16V V 11-15V 12-15V 13-16V 14-16V 15 NC 16 NC Lab K Effects cntact@lab-k-effects.cm 7

8 Fpsu bard Assembly intructins 1) Slder cmpnents n the PCB. 2) Slder the intercnnectin wires. Nte : Slder the intercnnectin wires as shwn in figure 1. Observe the rder red, black, blue, range. Figure 1 The psitive pin f rectifier bridge is indicated by a pint n the PCB. Vertical rientatin f dides Vreg bard Assembly intructins 1) Slder the cmpnents n the PCB except the regulatrs serial arrangement f the resistrs R4, R8: Lab K Effects cntact@lab-k-effects.cm 8

9 fixing fpsu and vreg bards 1 : Place the base with the 4 screws (A) and 4 plastic spacers (C). 2 : Screw the central spacer (D) f the FPSU bard using the screw (C). 3 : Place the FPSU card n the base. 4 : Fix the FPSU bard n the base with the nuts (J) and spacers (D). 5 : Fix the card VREG with cmpnents facing dwn with the nuts (J). 6 : Attach the heat sink (F) n the base with parker screws (E) placing tw screws (H) securing the clip int the hles prvided fr this purpse. 7 : Place insulatrs pads (K) and regulatrs in the rder. 8 : Attach the clip (G) n the heat sink (F) using washers (I) and nuts (J). 9 : Slder regulatrs and intercnnectin wires. 1 Place the base 2 Screw the central spacer 3 Place the bard n the base 4 Fix the bard n the base 5 Fix the VREG bard 6 Fix the heat sink 7 Place the regulatrs 8 Fix the clip 9 Slder the intercnnectin wires Lab K Effects cntact@lab-k-effects.cm 9

10 schematics Mentins légales : Lab K Effect shall nt be respnsible and disclaims all liability fr any damage (whether direct r cnsequential) that may result frm a wrng use f the kit by the user. Lab K Effects cntact@lab-k-effects.cm 10