INSTALLATION INSTRUCTIONS

Transcription

1 Lad: Min. 5 kg Max. 100 kg TS1000A TS700A INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main measures. 3. Parts included. 4. Installatin. 5. Adjusting the strke length f the lift. 6. Declaratin f cnfrmity. WARNING WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PROD- UCT MAY RESULT IN SERIOUS BODILY INJURY. 1 N. #

2 1. Imprtant safety Instructins. CAUTION: Befre yu begin any f the Installatin prcedures (4. Installatin.), read and fllw the warnings and safety instructins n this page. WARNING! THIS IS NOT A TOY! WARNING! CHILDREN SHOULD NOT OPERATE LIFT OR REMOTE CONTROL! Use the fllwing safety guidelines t help prtect yur lift frm ptential damage and t ensure yur wn persnal safety. Read all the installatin instructins befre testing r installing yur lift. Read and fllw all safety instructins. Keep remte cntrl ut f reach f children. T prevent bdily injury keep hands and clthing away frm the lift while the lift is in peratin. Befre installing the lift r wrking with its cnnectins, unplug the lift frm the electrical shck. D nt install the lift, pwer supply r R.F. mdule in places subject t extreme temperatures fr example near a radiatr, r heating vent. The TV lift must nly be munted in a dry area and it must ensured befre use that the lift is safe r prtected frm liquid cntact r spillage. T avid damaging the pwer supply, R.F. mdule and pwer crd, d nt put anything n it r place it where it culd becme damaged. Unplug the lift in the fllwing cnditins: When the pwer crd r plug is damaged r frayed. If liquid has spilled int the lift, pwer supply r RF mdule. If the lift, pwer supply r RF mdule has been expsed t rain r water. If the lift exhibits a distinct change in perfrmance, indicating a need fr servicing. MANUFACTURES wh build this Flat Lift int ther prducts r use it with ther prducts, MUST make sure t prevent bdily injury. The MANUFACTURER is respnsible t give the end user prper warnings and instructins fr use. 2

3 3. Parts included. Lift unit ( #1 ) Lid lifter ( #2 ) Lift brackets ( #3 ) TV munting brackets ( #4 ) (TS1000A nly) R.F. Mdule ( #5 ) Remte cntrl ( #6 ) AC input wire, cuntry cnfigured ( #7 ) Pwer supply bracket ( #8 ) Rcker switch ( #9 ) Pwer supply ( #10 ) Lid lifter ( #2 ) Lift brackets ( #3 ) Lift unit ( #1 ) TV munting brackets ( #4 ) (TS1000A nly) R.F. Mdule ( #5 ) Remte cntrl ( #6 ) Pwer supply ( #10 ) Rcker switch ( #9 ) AC input wire, cuntry cnfigured ( #7 ) Pwer supply bracket (#8) 5

4 4. Installatin. 1) Remve all cntents frm packaging and cmpare with parts list. 2) Place the lift unit (#1) n e.g. the back panel f cabinet in a lcatin that will allw full up and dwn mvement f the lift. 3) Fasten the unit securely t the cabinet. Screws must be apprpriate fr the material being used. 4) Cnnect the plugs frm lift unit (#1) and pwer supply (#10) t R.F. Mdule (#5). Please als refer t the separate user instructin fr the remte unit, next page. 5) Munt rcker switch (#9) n wanted lcatin by cutting a hle and pressing the switch int place. Secure excess wire t keep away frm mving parts. 6) Plug the pwer crd int wall utlet and test the lift. If the unit desn t wrk, check all cnnectins and retry. If still nt wrking, refer t truble shting guide n click supprt. Helpful hint: Munt TV lift and electrnics t plywd panel and attach t inside back f cabinet using apprpriate number f screws. This allws all cmpnents t be remved frm the cabinet if necessary. If this is nt pssible, create an access panel t the electrnics. 6

5 User instructin, RF remte system Installatin cnnect the pwer supply and the mtr unit t the remte receiver. 2 different plug sizes make this cnnectin nly pssible t make in the right way after having cnnected the plugs, the blue light will be lightning push the emitter buttns and the mtr unit will mve up and dwn fr stpping the mtin ne f the buttns need t be pushed Learning if the remte receiver d nt respnd when pushing the emitter buttns, reset the receiver. After that, cde the emitter and receiver tgether again Cding push the learner buttn n the receiver fr less than 1 sec. push ne f the emitter buttns the red light will start flashing push ne f the emitter buttns again and the red light will turn ff the units nw are cded tgether with a unique cde Reset push and hld dwn the learner buttn n the receiver fr 10 sec. (will be reset when the red light turns ff). 7

6 External rcker switch the external rcker switch can be cnnected t the receiver, if a fixed peratin unit is required. Truble shting check the plug cnnectins check whether the blue light is n reset the receiver and make a new cding Change f battery in emitter (type 27A/12V) remve lid n back side lift up battery place new battery FCC Statement This device cmplies with Part 15 f the FCC rules. Operatin is subject t the fllwing tw cnditins; 1) This device may nt cause any harmful interference and 2) This device must accept any interference received, including interference that may cause undesired peratin. 8

7 5. Adjusting the strke length f the lift. Adjusting the bttm stp: The bttm stp can be adjusted t any preferred height, e.g. if yu dn t want the lift t g all the way dwn int the cabinet. 1. Remve the 2 cvers. 2. Use an allen key t lsen the screw f the wire glider. Mve the glider t the preferred psitin and tighten the screw securely again. 3. Munt the 2 cvers again 9

8 Adjusting the tp stp: The tp stp can be adjusted t any preferred height, e.g. if yu dn t want the lift t g all the way ut f the cabinet. Use an allen key t lsen the screw f the wire glider. Mve the glider t the preferred psitin and tighten the screw securely again. 10