Electrical devices may only be mounted and connected by electrically skilled persons.
|
|
- Sherilyn Ford
- 5 years ago
- Views:
Transcription
1 Art. N. : FMHSD24 Operating instructins 1 Safety instructins Electrical devices may nly be munted and cnnected by electrically skilled persns. Serius injuries, fire r prperty damage pssible. Please read and fllw manual fully. Keep buttn cells ut f reach f children! If buttn cells are swallwed, get medical help immediately. Risk f explsin! D nt thrw buttn cells int a fire. Risk f explsin! D nt replace a used battery with a primary battery, e.g. lithium buttn cell. Fire hazard! Operatin exclusively with the pwer supplies listed under accessries The radi cmmunicatin takes place via a nn-exclusively available transmissin path, and is therefre nt suitable fr safety-related applicatins, such as emergency stp and emergency call. These instructins are an integral part f the prduct, and must remain with the end custmer. 2 Device cmpnents Figure 1: View (1) LC display (2) Menu buttns (3) Navigatin buttns (4) Functin keys (5) Charging cnnectin (6) Battery cmpartment (Rear side) (7) Status LED j00 1/18
2 3 Functin Intended use - Hand transmitter fr radi transmissin f switching, dimming, blind mvement and scene cmmands - Operatin with radi actuatrs frm the enet system Prduct characteristics - LC display fr user guidance - Menu buttns with changing assignments, depending n the menu cntext - Navigatin buttns fr rientatin in the menu - Three freely-cnfigurable functin key pairs - Status LED t display the transmissin status - 10 lists fr the cmpilatin f favurite functins - 16 scenes - All On and All Off - Lck-ut prtectin fr rller shutters r Venetian blinds - Restraint functin - Master dimming functin - Operatin with rechargeable battery (in the scpe f delivery) - Charging the battery with r withut charging cradle (accessry) r USB charging device - Charging cable included in the scpe f delivery Supplementary functins can be activated via enet server: - Operatin lcks - Update f the device sftware (nly with pwer supply cnnected) i The parameter list is in the Internet in the dcumentatin fr this device. 4 Operatin Display elements Figure 2: Screen panes in the display A: Title line A1: Menu title A2: Time display A3: Charging display B: Text area C: Fter fr status messages and fr displaying the functin f the menu buttns C1: Functin f the left menu buttn, cntext-dependent j00 2/18
3 C2: Functin f the right menu buttn, cntext-dependent The hand-held transmitter is perated using the buttns (4) r via the menu structure in the display using the navigatin buttns (3) n,, }, ~ and OK. 4.1 First steps i Befre using the hand-held transmitter, it must be cnnected t the switching, dimmer and Venetian blind actuatrs that are t be perated in the system. These steps are dcumented in the sectin "Cmmissining". Cautin! Only electrically skilled peple may perfrm wrk n electrical systems. Inserting the battery Befre first cmmissining, the enclsed battery must be inserted in the device. i Only use the prescribed battery type. D nt insert any ther buttn cells. Keep the cntacts f batteries and device free f grease. Open the battery cmpartment (6) n the rear side. Apply the battery t the psitive cntact f the battery hlder. Observe plarity: The psitive ple f the battery must be at the tp. Press gently n the battery t snap it in. Clse battery cmpartment. Charging the battery Use a device with a USB-A cnnectin fr charging, e.g. n a PC, r use a standard USB charging device. The enclsed battery has been inserted in the device. Cnnect the hand-held transmitter with the USB device using the enclsed USB cable. During a charging peratin, the charging display (A3) displays a prgress bar. Once a battery symbl appears here, the battery has been charged. i The charging cradle can als be used t charge the battery (accessry). Switching n the hand-held transmitter Press any buttn n the hand-held transmitter. i T activate the hand-held transmitter frm Standby mde, it is sufficient t mve it r shake it lightly. Switching ff the hand-held transmitter Select "Settings" and press OK. Select "Turn OFF device" and press OK. i The hand-held transmitter cannt be switched ff during charging. The message "Mains peratin" appears in the fter. 4.2 Basic functins Navigatin and selectin The hand-held transmitter is perated using the functin keys (4) r via the menu structure in the display using the navigatin buttns (3) and menu buttns (2): n mves the cursr upwards. mves the cursr dwnwards. }, ~ allw the adjustment f values. OK selects a highlighted menu item. Main menu The fllwing submenus are available in the main menu: - "Channels": Operatin f individual hand-held transmitter channels. j00 3/18
4 - "Scenes": Recalling and saving f scenes. - "Buttn lck": Lcks the buttns f the hand-held transmitter. - "Prgram": Opens the prgramming menu. The user can set the entries in the main menu and add t them using user-specific lists. Lists, channels and scenes can be named freely (see chapter 4.5. Setting up the hand-held transmitter). In the main menu, the menu buttns (2) have the functins "All On" and "All Off" assigned t them. Prgramming menu The fllwing submenus are available in the prgramming menu: - "Channels": Cnnect r discnnect hand-held transmitter channels and actuatrs; rename hand-held transmitter channels. - "Scenes": Integratin f actuatrs int scenes; renaming f scenes; remval f actuatrs frm scenes. - "Lists": Cmpilatin f user-specific lists cntaining hand-held transmitter channels and scenes. - "Buttn assignment": Assignment f hand-held transmitter channels t the functin keys (4). - "Settings": Opens the Settings menu. - "Advanced startup": Opens the cmmissining f the hand-held transmitter with the enet server. Settings menu. - "Hme screen": Cnfigures the main menu. - "Display": Setting f fnt size, language, display, brightness and active display time. - "Date/time": Setting f date and time; autmatic summer/winter time change-ver - "Factry Settings": Resetting f the entire device t the as-delivered state. - "Inf": Infrmatin n the hardware and sftware versin. - "Turn OFF device": Switching the device ff. Status LED As sn as a buttn is pressed r released, the status LED (7) first signals radi transmissin - LED turns red fr 3 secnds and then the actuatr status/grup status - LED turns green fr 3 secnds: At least ne actuatr is switched n, r ne Venetian blind is nt in the tp end psitin - LED remains ff: All the actuatrs are switched ff r the blinds are all in the upper end psitin r - if there is n status message frm an actuatr - a transmissin errr. - The LED rapidly flashes red fr 5 secnds: The status message f at least ne actuatr is missing 4.3 Operating actuatrs with rckers The functin keys (4) allw direct access t the mst imprtant functins. The user can freely select the assignment frm the saved cnnectins. Operating light Switch n: Brief press f left buttn. Switch ff: Brief press f right buttn. Dim brighter: Lng press f left buttn. The dimming prcess ends when the buttn is released. Dim darker: Lng press f right buttn. The dimming prcess ends when the buttn is released. Operating blind Mve Venetian blind upwards: Lng press f left buttn. Mve Venetian blind dwnwards: Lng press f right buttn. j00 4/18
5 Stp r adjust Venetian blind: Shrt press f right r left buttn. Operating switch actuatr Press the right r left buttn: The lad is switched n fr the duratin f the buttn-press. i The maximum actuatin length is 60 secnds. Recalling scenes Press the scene buttn briefly. Actuatrs switch t the saved scene values. Changing scene Press the scene buttn briefly. Actuatrs switch t the saved scene value. Set new scene values. Press scene buttn fr lnger than 4 secnds. Actuatrs first switch t the saved scene value and save the new scene value after 4 secnds. Dimming a scene The dimmer actuatrs in a recalled scene can be dimmed, althugh the brightness differences between the individual dimmer actuatrs remain. The master dimming functin must be assigned t a rcker (see chapter 4.5. Setting up the hand-held transmitter). Recall a scene - either using the scene menu r a functin key. Dim brighter: Lng press f the left master dimming buttn. Dim darker: Lng press f the right master dimming buttn. 4.4 Operating the hand-held transmitter Operating actuatrs with the channel menu The "Channels" menu ffers direct access t all 24 hand-held transmitter channels, irrespective f whether r nt actuatrs are cnnected. Select "Channels" and press OK. Select the desired hand-held transmitter channel. Switch n: Brief press f ~ buttn. Switch ff: Brief press f } buttn. Tggle: Brief press f OK buttn. Dim brighter: Lng press f ~ buttn. Dim darker: Lng press f } buttn. Mve Venetian blind dwnwards: Lng press f } buttn. Mve Venetian blind upwards: Lng press f ~ buttn. Stp Venetian blind: Shrt press f } r ~ buttn. Return t main menu: Press the left menu buttn "Back". Operating actuatrs with the list menu When set up, lists can cntain selected hand-held transmitter channels r scenes and be given sensible names accrding t the requirements f the peratr (see chapter 4.5. Setting up the hand-held transmitter). Select the desired list in the menu and press OK. Select the desired hand-held transmitter channel. Operatin takes place with the } and ~ buttns. j00 5/18
6 Return t main menu: Press the left menu buttn "Back". Save switch-n brightness A switch-n brightness can be set and saved fr dimmer actuatrs. Select "Channels" and press OK. Select the desired hand-held transmitter channel. Set required switch-n brightness. Press the right menu buttn "Open". Select "Set Startvalue" and press OK. The light is briefly switched ff and switched n again t the switch-n brightness. Switchn brightness is saved. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. Scene menu: Recall scenes The "Scenes" menu ffers 16 scenes, irrespective f whether r nt actuatrs are cnnected, as well as the functins 'Channel lck' and 'Lck-ut prtectin'. Select "Scenes" and press OK. Select the desired scene and press OK. The message "Scene called" appears in the fter. Return t main menu: Press the left menu buttn "Back". Scene menu: Changing a scene Call up the scene t be changed. Change the active scene as desired. Return t the scene menu. Select the desired scene and press the right menu buttn "Open". Select "Stre scene" and press "Save". The message "Stre scene" appears in the fter. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. Activating and remving a buttn lck The buttn lck lcks all the buttns f the hand-held transmitter against peratin. Activating the buttn lck: Open the main menu, select the menu item "Buttn lck" and press OK. All the push-buttn functins f the hand-held transmitter are disabled. The display indicates this state. Remving a buttn lck: Press the right menu buttn "Unlck" fr apprx. 3 secnds. 4.5 Setting up the hand-held transmitter Creating lists Lists allw quick access t frequently used hand-held transmitter channels r scenes. Lists can be accessed using apprpriate names in the main menu. The hand-held transmitter is cnnected t all the actuatrs that are t be perated. Select "Lists" and press OK. Select the desired list and press OK. Select "Assign functin" and press OK. j00 6/18
7 The list with all the available hand-held transmitter channels and scenes appears in the display. Select the hand-held transmitter channels and scenes, ne after anther. Cnfirm each selectin with OK. Selected entries are indicated by >. Saving a list: Press the right muse-buttn "Save". The message "Stre list" appears in the fter. Exiting a list: Press the left menu buttn "Back". Renaming a list A list name can cntain a maximum f 15 characters. Select "Lists" and press OK. Select the desired list and press OK. Select "Rename list" and press OK. The "Edit text" windw appears in the display. Enter the list name (see chapter "Entering texts"). Saving an entry: Press the right muse-buttn "Save". The message "Stre list" appears in the fter. Exiting "Edit text": Press the right menu buttn "Back". Arranging a list Users can srt the entries within a list hwever they wish. Functins must be assigned befre a list is srted. Select "Lists" and press OK. Select the desired list and press OK. Select "Arrange list" and press OK. The list with all the assigned hand-held transmitter channels and scenes appears in the display. If the list is empty, n functins are assigned. Using the n r buttns, select a list entry. Cnfirm the selectin with OK. The selected entry is indicated with <>. Using the } r ~ buttns, mve the selected entry and press OK. The highlighting <> disappears. Once the list has been srted as required, press the right menu buttn "Save". The message "Stre list" appears in the fter. Exiting a list: Press the left menu buttn "Back". Cnnecting the functin keys with the hand-held transmitter channel The functin keys (4) allw direct access t the mst imprtant functins. Fr individual handheld transmitter channels, buttns next t ne anther are cmbined t frm a rcker. The hand-held transmitter is cnnected t all the actuatrs that are t be perated. Select "Buttn assignment" and press OK. Select the desired buttn - 1, 2 r 3 - and press OK. Select the desired functin channel, scene, master dimming r "n functin". Assigning a channel: Select the desired channel and press OK. j00 7/18
8 Assigning a scene: Select the left r right buttn and press OK. Select the desired scene and press OK. A message appears in the fter, stating that the functin is being saved. The selected entry is indicated with >. Exiting the selectin windw: Press the left menu buttn "Back". Entering texts The "Edit text" windw appears when hand-held transmitter channels, scenes r lists are t be renamed. It cntains an entry line and three selectin lines in the text area. The selectin lines prvide the letters A...Z, the numerals and sme special characters. Selecting and entering characters: In the selectin lines, mark the desired characters and press OK. The selected character appears in the entry line. Switching between upper and lwer-case letters: Highlight the character ğ and press OK. Deleting r crrecting the mst recently entered character: In the selectin line, highlight the character Ğ and press OK. Selecting entries fr the main menu Select "Settings" and press OK. Select "Hme screen" and press OK. Select "Select" and press OK. Select the desired entries and press OK. The selected entry is indicated with >. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. The selected entries are available in the main menu. i The "Prgramming" entry is always available and cannt be deactivated. 4.6 Settings Setting the fnt size Select "Settings" and press OK. Select "Display" and press OK. Select "Fnt size" and press OK. Depending n requirements, select the fnt size "Small" r "Big". The text area is shwn in the selected fnt size. The selectin is indicated with >. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. Selecting a language Select "Settings" and press OK. Select "Display" and press OK. Select "Language" and press OK. Select the desired language and press OK. The text area is shwn in the selected language. The selectin is indicated with >. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. j00 8/18
9 Selecting the display Select "Settings" and press OK. Select "Display" and press OK. Select "Inverse display" and press OK. The display is inverted - bright text n dark backgrund r vice-versa. The selectin is indicated with >. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. Setting the display brightness The display brightness can be set in 16 levels. Select "Settings" and press OK. Select "Display" and press OK. Select "Brightness". Increase display brightness: Press the ~ buttn. Reduce display brightness: Press the } buttn. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. Set active display time The active display time determines the time, after which the display switches t energy-saving mde and switches ff. The backlighting switches ff after half f the set time. Select "Settings" and press OK. Select "Display" and press OK. Select "Active display time". Increase active display time: Press the ~ buttn. Decrease active display time: Press the } buttn. Return t main menu: Press the left menu buttn "Back" fr apprx. 1 secnd. j00 9/18
10 5 Infrmatin fr electrically skilled persns 5.1 Fitting and electrical cnnectin Munting the charging cradle Figure 3: Charging cradle fr hand-held transmitter - Rear view The ptinal charging cradle (accessry) gives the hand-held transmitter its permanent place. The charging cradle can be perated when munted n a flat surface as a table-tp device r munted n the wall. When munting it n the wall, use a screw with a screw head < 8 mm, e.g Screw spacing 60 mm. Selecting a suitable munting lcatin near t a scket r n a flush-munted USB pwer supply. Cuntersink the screws int the wall t apprx. 3 mm. D nt break ut the munting lcks. Place the charging cradle nt the munted screws and fix them by applying slight dwnward pressure. Cnnect the charging cradle with the USB pwer supply. 5.2 Cmmissining DANGER! Electrical shck when live parts are tuched. Electrical shcks can be fatal. During cmmissining, cver the parts carrying vltage n radi transmitters and actuatrs and in their surrunding area. Cnnecting the hand-held transmitter channel with the actuatr i Up t 10 radi actuatrs can be cnnected t a transmitter in a single step. Select "Channels" and press OK. Select the desired hand-held transmitter channel and press OK. Select "Teach chanel" and press OK. Status LED (7) flashes red. The hand-held transmitter is in prgramming mde fr apprx. 1 minute. j00 10/18
11 Switch the actuatr channels t prgramming mde (see actuatr instructins). The hand-held transmitter signals the number f actuatr channels fund. Press the right menu buttn "Teach". The status LED lights up fr apprx. 5 secnds. The selected hand-held transmitter channel is cnnected t the actuatr. The hand-held transmitter and actuatr exit the prgramming mde autmatically. i The All On and All Off buttns f the hand-held transmitter are cnnected t the actuatr autmatically as sn as the first cnnectin t a radi transmitter takes place. i If the status LED f the radi transmitter flashes 3 times at 1-secnd intervals fr apprx. 5 secnds, then the prgramming peratin was nt successful. The actuatr is utside radi range, nt in prgramming mde r there are radi faults. i If the status LED f the actuatr flashes 3 times at 1-secnd intervals fr apprx. 5 secnds, then the prgramming peratin was nt successful. All the memry lcatins in the actuatr r radi transmitter are ccupied. i T terminate prgramming mde early, press the left menu buttn "Back". Renaming a hand-held transmitter channel Select "Channels" and press OK. Select the desired channel and press OK. Select "Rename channel" and press OK. The "Edit text" windw appears in the display. Enter a new name (see chapter "Setting up the hand-held transmitter", "Entering texts"). Saving an entry: Press the right muse-buttn "Save". The message "Text stred" appears in the fter. Exiting "Edit text": Press the left menu buttn "Back". Discnnecting the cnnectin between a hand-held transmitter channel and an actuatr The cnnectin between a hand-held transmitter channel and an individual actuatr is discnnected by repeating the cnnectin steps: Select "Channels" and press OK. Select the desired hand-held transmitter channel and press OK. Select "Teach chanel" and press OK. Status LED (7) flashes red. The hand-held transmitter is in prgramming mde fr apprx. 1 minute. Switch the actuatr channels t prgramming mde (see actuatr instructins). The hand-held transmitter signals the number f actuatr channels fund. Press the right menu buttn "Teach". The status LED flashes quickly fr apprx. 5 secnds. The selected hand-held transmitter channel is discnnected frm the actuatr. The hand-held transmitter and actuatr exit the prgramming mde autmatically. Discnnecting the cnnectin between a hand-held transmitter channel and all the actuatr channels Select "Channels" and press OK. Select the desired hand-held transmitter channel and press OK. Select "Reset channel" and press OK. j00 11/18
12 A security query is displayed, asking whether the peratin shuld be cntinued r nt. Cancel peratin: Press the left menu buttn "N". - r - Cntinue peratin: Press the right menu buttn "Yes". The message "Reset executed" appears in the fter. All the actuatr channels cnnected t the selected hand-held transmitter channel are discnnected. Cnnecting a scene channel with the actuatr Select "Scenes" and press OK. Select the desired scene and press OK. Press "Teach scene" and OK. Status LED (7) flashes red. The hand-held transmitter is in prgramming mde fr apprx. 1 minute. Switch the actuatr channels t prgramming mde (see actuatr instructins). The hand-held transmitter signals the number f actuatr channels fund. Press the right menu buttn "Teach". The status LED lights up fr apprx. 5 secnds. The selected hand-held transmitter channel is cnnected t the actuatr. The hand-held transmitter and actuatr exit the prgramming mde autmatically. i If the status LED f the radi transmitter flashes 3 times at 1-secnd intervals fr apprx. 5 secnds, then the prgramming peratin was nt successful. The actuatr is utside radi range, nt in prgramming mde r there are radi faults. i If the status LED f the actuatr flashes 3 times at 1-secnd intervals fr apprx. 5 secnds, then the prgramming peratin was nt successful. All the memry lcatins in the actuatr r radi transmitter are ccupied. i T terminate prgramming mde early, press the left menu buttn "Back". Rename scene Select "Scenes" and press OK. Select the desired scene and press OK. Select "Rename scene" and press OK. The "Edit text" windw appears in the display. Enter a new name (see chapter "Setting up the hand-held transmitter", "Entering texts"). Saving an entry: Press the right muse-buttn "Save". The message "Text stred" appears in the fter. Exiting "Edit text": Press the left menu buttn "Back". Remving an individual actuatr channel frm a scene An individual actuatr is remved frm a scene by repeating the cnnectin steps: Select "Scenes" and press OK. Select the desired scene and press OK. Press "Teach scene" and OK. Status LED (7) flashes red. The hand-held transmitter is in prgramming mde fr apprx. 1 minute. Switch the actuatr channels t prgramming mde (see actuatr instructins). j00 12/18
13 The hand-held transmitter signals the number f actuatr channels fund. Press the right menu buttn "Teach". The status LED lights up fr apprx. 3 secnds. The actuatr channels are deleted frm the scene. The hand-held transmitter and actuatr exit the prgramming mde autmatically. Resetting a scene All the cnnectins f the scene channel t actuatrs are discnnected. i The cnnectins in the actuatrs are preserved and must be deleted separately. Select the desired scene and press OK. Select "Scenes" and press OK. Select "Reset scene" and press OK. A security query is displayed, asking whether the peratin shuld be cntinued r nt. Cancel peratin: Press the left menu buttn "N". - r - Cntinue peratin: Press the right menu buttn "Yes". The message "Reset executed" appears in the fter. All the actuatrs cnnected t the selected scene are discnnected. Setting up lck-ut prtectin The lck-ut prtectin functin mves the blind/shutter t the tp end psitin fr selected Venetian blind actuatrs e.g. fr pati r balcny drs and lcks further peratin. Cnnect tw scenes fr activating and deactivating the lck-ut prtectin with the desired Venetian blind actuatr (see chapter Cnnecting a scene channel with an actuatr). Give the scene a suitable name (see chapter Renaming a scene). Select "Scenes" and press OK. Select the scene fr activating lck-ut prtectin and press the right menu buttn "Open". Select "Lck-ut prt. ON" and press OK. The entry is indicated with >. Press the left menu buttn "Back". Select the scene fr deactivating lck-ut prtectin and press the right menu buttn "Open". Select "Lck-ut prt. OFF" and press OK. The entry is indicated with >. Press the left menu buttn "Back". The lck-ut prtectin functins are indicated with ĝ. Exiting Scenes menu: Press the left menu buttn "Back". Setting up the channel lck functin A channel lck functin sets values, states r Venetian blind psitins and then lcks autmatic r manual peratin until an enable is perfrmed. Cnnect tw scenes fr activating and deactivating the channel lck with the desired actuatrs (see chapter Cnnecting a scene channel with an actuatr). Give the scene a suitable name (see chapter Renaming a scene). Set the switching dimmer and Venetian blind actuatrs with the desired values fr the restrained situatin. Select "Scenes" and press OK. j00 13/18
14 Select the previusly-created scene fr activating the functin and press the right menu buttn "Open". Select "Channel lck ON" and press OK. The entry is indicated with >. Select "Stre scene" and press OK. Press the left menu buttn "Back". Select the previusly-created scene fr deactivating the functin and press the right menu buttn "Open". Select "Channel lck OFF" and press OK. The entry is indicated with >. Press the left menu buttn "Back". The channel lck functins are indicated with ĝ. Exiting Scenes menu: Press the left menu buttn "Back". Preparing a hand-held transmitter fr peratin with an enet server The hand-held transmitter must be cnnected with the server fr installatins cmmissined with the enet server. Select "Advanced startup" and press OK. "Teaching mde" is activated and the LED flashes red. Start reading in f devices n the enet server. If the enet server requests actuatin f a buttn, select "Send cnfirmatin" and press OK. Once prgramming f the hand-held transmitter by the enet server has been cmpleted, select "Teaching mde" again and press the right menu buttn "On/Off". The hand-held transmitter signals "End f Teaching mde" in the fter. Resetting the hand-held transmitter t the default setting All the cnnectins t actuatrs are discnnected. The parameters are reset t the default setting. i The cnnectins in the actuatrs are preserved and must be deleted separately. Select "Settings" and press OK. Select "Default setting" and press OK. In the text area, the message "Reset device?" appears. Press the right menu buttn "Yes". The message "Executing reset" appears in the fter. The cnnectins f all the hand-held transmitter and scene channels t all the actuatrs are discnnected. The hand-held transmitter returns t the main menu. 6 Appendix Remve empty batteries immediately and dispse f in an envirnmentally friendly manner. D nt thrw batteries int husehld waste. Cnsult yur lcal authrities abut envirnmentally friendly dispsal. Accrding t statutry prvisins, the end cnsumer is bligated t return used batteries. 6.1 Technical data Rated vltage DC 3.6 V Battery type 1 Lithium LIR 2477 Dimensins L W H mm Ambient temperature C j00 14/18
15 Degree f prtectin IP 20 Radi frequency MHz Transmissin capacity max. 20 mw Transmitting range in free field typ. 100 m Receiver categry Parameter list The device parameters can be changed with the enet server: Settings windw Device settings Parameter name Manual cmmissining Setting ptins, Basic setting On, Off Basic setting: On Explanatins Disables manual cmmissining fr all device channels. Name, list 1 t 10 Free text, maximum 15 characters Basic setting: List 01 t list 10 Fnt size Inverted display Language Small, large Basic setting: Large Off, On Basic setting: On German, English, Dutch, Nrwegian, Spanish, French Basic setting: German Display brightness 1 t 16 Basic setting: 10 Clck: Minutes 0 t 59 Basic setting: 0 Clck: Hurs 0 t 23 Basic setting: 0 Clck: Weekday Mnday t Sunday Basic setting: Sunday Clck: Day 1 t 31 Basic setting: 1 Clck: Mnth 1 t 12 Basic setting: 1 Clck: Year 1 t 99 Basic setting: 12 Clck: Summer time changever On, Off Basic setting: On Nte: In the "Off" setting, the device cannt be reset t the factry setting. List designatins f List 1 t 10 Setting f the fnt size fr displaying characters. Switch-ver between black fnt n white backgrund and white fnt n black backgrund. Setting f the display language. Brightness setting f the display. Setting f the current time: Minutes. Setting f the current time: Hurs. Setting f current weekday Setting f current date: Day. Setting f current date: Mnth. Setting f current date: Year. Clck setting fr autmatic switch-ver t summer and winter time. j00 15/18
16 Light run-n time Functin, rcker switch 1 t 3 Channel index, left buttn f rcker switch 1 t 3 Channel index, right buttn f rcker switch 1 t 3 Settings, channel/scene Parameter name Lcal Operatin Manual cmmissining 10 t 60 secnds Basic setting: 40 secnds Rcker switch, scene, master dimming, nne Basic setting: Rcker In the setting "Rcker switch": 17 t 40 Basic setting: 17 t 19 In the setting as scene buttn: 1 t 16 Basic setting: 1 t 3 In the setting as scene buttn: 1 t 16 Basic setting: 1 t 3 Setting ptins, Basic setting On, Off Basic setting: On On, Off Basic setting: On Time fr which the display illuminated remains switched after the last buttn-press. The setting is made in jumps f 2 secnds. A factr between 5 and 30 must be entered. Setting the functin keys. Setting "Rcker switch": Adjacent buttns are cmbined t frm a rcker and wrk as channel buttns. Setting "Scene:" Bth buttns wrk as scene buttns. Setting "Master dimming": The dimmer actuatrs in a recalled scene can be dimmed. Setting "Nne": The functin keys have n functin. Cnnecting the functin keys with the desired channel. Values 17 t 40 crrespnd t the channels 1 t 24. Values 1 t 16 crrespnd t the scenes 1 t 16. Cnnecting the functin keys with the desired channel. Values 1 t 16 crrespnd t the scenes 1 t 16. Explanatins Blcks the device channel fr lcal peratin. Blcks manual cmmissining fr the device channel. Nte: In the "Off" setting, the device cannt be reset t the factry setting. j00 16/18
17 Sum status / transmissin repetitins On, Off/Transmit 2x 11x, Off/Transmit 4x (withut cnnectin) On: The transmitter evaluates the received status messages and displays them as a sum status. If individual status messages fail, then the transmitter will repeat its telegram up t three times. Off/Transmit... times: The evaluatin and display f the verall status is deactivated. The number f telegram repetitins is prescribed. In this setting, n transmissin errrs are displayed. Scene name 1 t 16 Free text, maximum 15 characters Channel name 01 t 16 Free text, maximum 15 characters Off/Transmit 4x (withut cnnectin): Reserved fr sensrs which transmit withut a cnnectin. Scene designatins f scenes 1 t 16. Channel designatins f channels 1 t Trubleshting After a brief buttn-press, the hand-held transmitter switches ff. Cause: Battery in the hand-held transmitter is almst empty. Charge the hand-held transmitter using the USB cnnectin. If the prblem persists: Battery is wrn ut. Replace it with a new battery. Receiver des nt react, status LED displays a transmissin errr. Status LED flashes red quickly fr 5 secnds. Cause 1: Radi range exceeded. Structural bstacles reduce the range. Insert a radi repeater. Cause 2: Actuatr is nt ready fr peratin. Check the actuatr and mains vltage. Cause 3: There are radi faults, e.g. thrugh utside radi. Eliminate radi interference. i The actuatr causing the transmissin errr can be remved frm the display f transmissin errrs. T d this, pen the main menu. Select "Channels" and press OK. Select the desired hand-held transmitter channel, press OK and then "Open". During signalling, select "Status exclusin" and press OK. The status LED lights up red. The message "Status exclusin" appears in the fter. The actuatr is autmatically taken int accunt again when it transmits a status message after radi transmissin. The prgramming mde cancels after a few secnds. There is an enet server in scan mde within radi range. Terminate scan mde n the enet server. 6.4 Accessries Dcking statin USB charger USB pwer supply unit, 5 V / 500 ma j00 17/18 Art. N. FM HS TF Art. N USB
18 Albrecht Jung GmbH & C. KG hereby declares that the radi system type Art. N. FMHSD24 crrespnds t the directive 2014/53/EU. Yu can find the full article number n the device. The cmplete text f the EU Declaratin f Cnfrmity is available under the Internet address: Warranty The warranty fllws abut the specialty stre in between the legal framewrk as prvided fr by law. ALBRECHT JUNG GMBH & CO. KG Vlmestraße Schalksmühle GERMANY Telefn: Telefax: kundencenter@jung.de j00 18/18
Electrical devices may only be mounted and connected by electrically skilled persons.
2-gang Art. N. : HS2 RF 4-gang Art. N. : HS4 RF Operating instructins 1 Safety instructins Electrical devices may nly be munted and cnnected by electrically skilled persns. Serius injuries, fire r prperty
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Order N. : 5323 02 Operating instructins 1 Safety instructins Electrical devices may nly be munted and cnnected by electrically skilled persns. Serius injuries, fire r prperty damage pssible. Please read
More informationFigure 1: View, connection compartment closed
Radi Management Art. N. : 2700AP Operating instructins 1 Safety instructins Electrical equipment may nly be installed and fitted by electrically skilled persns. Serius injuries, fire r prperty damage pssible.
More informationRiverSurveyor S5/M9 & HydroSurveyor Second Generation Power & Communications Module (PCM) Jan 23, 2014
SnTek, a Xylem brand 9940 Summers Ridge Rad, San Dieg, CA 92121-3091 USA Telephne (858) 546-8327 Fax (858) 546-8150 E-mail: inquiry@sntek.cm Internet: http://www.sntek.cm RiverSurveyr S5/M9 & HydrSurveyr
More informationLED wdali MC Switch Input Modul Set - User Manual
LED wli MC Switch Input Mdul Set - User Manual Buttn mdul (Transmitter) 1. Prduct Descriptin Item N.: LC-004-302 Receive mdul (Receiver) The wli MC Switch Input Mdul Set is a cmpact wireless Multi Cntrl
More informationINSTALLATION INSTRUCTIONS
Lad: Min. 5 kg Max. 100 kg TS1000A TS700A INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main measures. 3. Parts included. 4. Installatin. 5. Adjusting the strke
More informationINSTALLATION INSTRUCTIONS
Lad with min. 5 kg 405000090 405070090 INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main dimensins. 3. Parts included. 4. Installatin. 5. Adjusting the strke
More informationKELOX room thermostats - KM690D Digital-Standard/ KM690U Digital-Control
KELOX rm thermstats - KM690D Digital-Standard/ KM690U Digital-Cntrl The KELOX rm thermstats are high-quality rm temperature cntrllers fr recrding and cntrlling the required rm temperature fr a maximum
More informationCAR ASYST - Quick Start Guide MAIN MENU
fficially apprved by CAR ASYST - Quick Start Guide MAIN MENU Main menu The main menu f ur CAR ASYST APP is divided int 7 menu items. Belw yu will find a list f these items including a shrt descriptin.
More informationCUSTOMER PORTAL. Floorplan Management
CUSTOMER PORTAL Flrplan Management FLOORPLAN ANALYTICS The flrplan analytics area displays flrplans yu have uplad t the prtal (if yu haven t yet upladed a flrplan please cntact ur supprt department). Frm
More informationSISTEMA ELEVATÓRIO ETV 460A
Parts included with yur Flat Lift Lift unit ( #1 ) Pwer supply ( #2 ) R.F. Mdule ( #3 ) Rcker switch ( #4 ) Remte Cntrl ( #5 ) Lift unit ( #1 ) Remte Cntrl ( #5 ) Pwer supply ( #2 ) Rcker switch ( #4 )
More informationAltis Flight Manager. PC application for AerobTec devices. AerobTec Altis v3 User Manual 1
Altis Flight Manager PC applicatin fr AerbTec devices AerbTec Altis v3 User Manual 1 Table f Cntents Intrductin...3 Requirements...3 Installatin...3 Applicatin...3 USB Driver fr Altis v3 interface ALink...4.NET
More informationAIR CONDITIONER REMOTE CONTROLLER ILLUSTRATION CS406-R51E
AIR CONDITER REMOTE CONTROLLER ILLUSTRAT CS406-R5E 00550905 0009 Thank yu very much fr purchasing ur air cnditiner. Please read this wner's manual carefully befre using yur air cnditiner. CONTENTS Handling
More informationBV4115. RF Packet Transmitter. Product specification. February ByVac 2007 ByVac Page 1 of 5
Prduct Specificatin Prduct specificatin. February 2007 ByVac 2007 ByVac Page 1 f 5 Prduct Specificatin Cntents 1. Dcument Versins... 2 2. Intrductin... 2 3. Features... 2 4. Battery Life... 2 5. Blck Diagram...
More informationDispatcher Control for MotoTRBO Capacity Plus Systems
Dispatcher Cntrl fr MtTRBO Capacity Plus Systems This tutrial prvides brief instructins t set up the dispatch cntrl ver MtTRBO Capacity Plus systems, using SmartPTT dispatch sftware. Bth cases are cnsidered:
More informationTen-Tec Model RX-366 Subreceiver 565/566 Subreceiver Installation and Operation Manual-74467
Ten-Tec Mdel RX-366 Subreceiver 565/566 Subreceiver Installatin and Operatin Manual-74467 Tls required: Sldering irn r heat gun (fr shrinking heat shrink tubing) Number 1 Phillips screw driver Number 2
More information1.12 Equipment Manager
Mdule 1 Categry 1 1.12 Equipment Manager Functin f the windw The windw is the central data file fr the Kntrl Pr and cllects the main data fr fees f an bject that t be used in this prject. The Equipment
More informationINSTALLATION INSTRUCTIONS
Lad: Min. 5 kg Max. 100 kg TS1000A TS700A INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main measures. 3. Parts included. 4. Installatin. 5. Adjusting the strke
More informationLED DALI MC+ Switch Input Module - User Manual
LED MC+ Switch Input Mdule - User Manual Item n.: LC-004-301 1. Prduct Descriptin The MC+ is a Cmpact Multi Cntrl mdule with 4 freely prgramable swithcing inputs (ptential-free clsing cntacts). The supply
More informationRemote Control Learn Button Receiver Input Connections
Remte Cntrl Learn Buttn Receiver Input Cnnectins Remte Cntrl LED Light Wi-fi/Factry Reset Buttn Receiver Output Cnnectin Heartbeat LED Light PRV Cnnectins Pwer Reset Buttn Pl / Treadmill Switch Flat Switch
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Art. No. : FM..1561.07.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationOperating Instructions
TC 60/8 THERMOCOMPUTER TC 60/8 temp / time s s temp / time k start stp Operating Instructins Cntents General Infrmatin...1 Security Advice...1 Firing Curves...1 Typical Firing Curves...2 Entering a Firing
More informationExcel Step by Step Instructions Creating Lists and Charts. Microsoft
Infrmatin Yu Can Enter in a Wrksheet: Labels: Any type f text r infrmatin nt used in any calculatins. Labels are used fr wrksheet headings and make wrksheets easy t read and understand. Labels can als
More informationVIP-200. Point to Point Extension Configuration Quick Start Guide. Video over IP Extender and Matrix System
VIP-200 Vide ver IP Extender and Matrix System Pint t Pint Extensin Cnfiguratin Quick Start Guide PureLink TM 535 East Crescent Avenue Ramsey, NJ 07446 USA Cntents What is in the bx... 3 Transmitter kit
More informationLINE POWER SUPPLIES Low-Loss Supplies for Line Powered EnOcean Modules
Lw-Lss Supplies fr Line Pwered EnOcean Mdules A line pwer supply has t ffer the required energy t supply the actuatr electrnic and t supply the EnOcean TCM/RCM radi cntrl mdule. This paper cntains sme
More informationUniversal input/output controller
Embedded autmatin equipment (Shanghai) Limited Rm 305. Twer B.NO.18Talin rad Pudng District, Shanghai Phne: +86-21-51090839/50750355, fax: +86-21-50758598, e-mail: sales@stammkn.cm Universal input/utput
More informationSecurity Exercise 12
Security Exercise 12 Asynchrnus Serial Digital Baseband Transmissin Discussin: In this chapter, yu learned that bits are transmitted ver a cpper wire as a series f vltage pulses (a prcess referred t as
More information2015 Chevrolet Corvette Corvette Service Manual Body Systems Vehicle Access Repair Instructions Document ID:
xtltipelement Service Infrmatin 2015 Chevrlet Crvette Crvette Service Manual 7527625 Bdy Systems Vehicle Access Repair Instructins Dcument ID: 3448513 Remte Cntrl Dr Lck and Theft Deterrent Transmitter
More informationOwner s Manual Installation and Operating Instructions
Meitav-tec Ltd (Cntel grup) Tel: +972 (3) 962 6462 Fax: +972 (3) 962 6620 www.meitavtec.cm - supprt@meitavtec.cm ETN-24-P-1S Owner s Manual Installatin and Operating Instructins Please read this manual
More informationDXF2DAT 3.0 Professional Designed Computing Systems 848 W. Borton Road Essexville, Michigan 48732
Prgram Infrmatin 1 DXF2DAT 3.0 Prfessinal Designed Cmputing Systems 848 W. Brtn Rad Essexville, Michigan 48732 Cntact: (989) 892-4376 website: http://www.famwrk.net General Infrmatin: inf@famwrk.net Technical
More informationRS232 Communication Between a Sunny Boy 2500U and a PC. Technical Note
RS232 Cmmunicatin Between a Sunny By 2500U and a PC Technical Nte Revisin 1.5 July 8, 2003 Kent Sheldn Revisin Histry 1.5 July 8, 2003 Kent Sheldn Cntact update 20830 Red Dg Rad Grass Valley, CA 95945
More informationTROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE Dcument revisin 1.3 Last revised: December 6, 2017 Recn Wireless Blckage and Flw Mnitr Trubleshting Guide 2014-2017 Intelligent Agricultural Slutins All Rights Reserved. Recn Wireless
More informationTension meter dynaline HF45/LPT
Tensin meter dynaline HF45/LPT EN Operatin and maintenance manual SUMMARY 1. DEFINITIONS... 3 2. PICTOGRAMS USED IN THIS MANUAL... 3 3. STANDARD CONTENT OF DELIVERY... 3 4. INTRODUCTION... 4 4.1. Descriptin...
More informationDesktop Teller Exception User Guide
Desktp Teller Exceptin User Guide Jammed Dcuments If a dcument jams during the scanning prcess, the scanner will stp, and a message bx will display a Device Errr Message, as shwn belw: Click OK t allw
More informationSpectracom GSG ecall Test Suite
18-Dec-2017 GSG App Nte Spectracm GSG ecall Test Suite Table f Cntents 1. Intrductin... 1 2. Befre Starting the Test... 2 3. Running the ecall Test Suite... 4 4. Psitin Errr Tests 2.2.2-2.2.4... 10 5.
More informationSolarEdge. Immersion Heater Controller Installation Guide. For Europe, APAC & South Africa Version 1.6
SlarEdge Immersin Heater Cntrller Installatin Guide Fr Eurpe, APAC & Suth Africa Versin 1.6 Cntents Cntents HANDLING AND SAFETY INSTRUCTIONS 2 Safety Symbls Infrmatin 2 Immersin Heater Cntrller Installatin
More informationSoftware manual. GoPal Navigator Version 5
Sftware manual GPal Navigatr Versin 5 GPal Navigatr Versin 5 Cntents CHAPTER 1: INTRODUCTION... 1 Greeting...1 Cntents f CD/DVD...1 System requirements...3 Cnventins in this manual...3 Tips and warnings...4
More informationTension meter dynarope HF37/2/LPT
Tensin meter dynarpe HF37/2/LPT EN Operatin and maintenance manual SUMMARY 1. DEFINITIONS... 3 2. PICTOGRAMS USED IN THIS MANUAL... 3 3. STANDARD CONTENT OF DELIVERY... 3 4. INTRODUCTION... 4 4.1. Descriptin...
More informationNanoScan v2 Readme Version 2.7. Change log. v2.7 - Added information for new product Pyro/9/5-MIR.
NanScan v2 Readme Versin 2.7 Change lg v2.7 - Added infrmatin fr new prduct Pyr/9/5-MIR. v2.6 - Redesigned Messages windw. Imprved readability and ease f use. Mves almst all pp up message bxes int the
More informationS-400 Series User Guide
S-400 Series User Guide temptimecrp.cm Ntices and Safety 1 Ntices and Safety 1.1 Disclaimer and limitatin f liability Temptime assumes n respnsibility fr any lss r claims by third parties which may arise
More informationOperating Instructions
TC 40 THERMOCOMPUTER TC 40 start stp Operating Instructins Cntents General Infrmatin...1 Security Advice...1 Firing Curves...1 Typical Firing Curves...2 Entering a Firing Curve...2 Checing the Prgramme
More informationTC 60 THERMOCOMPUTER TC 60. prog. start stop. Operating Instructions
TC 60 prg start stp THERMOCOMPUTER TC 60 h C/h C Operating Instructins Cntents General Infrmatin...1 Security Advice...1 Firing Curves...1 Typical Firing Curves...2 Entering a Firing Curve...2 Checing
More informationVM1AT-R1 INDUSTRIAL MICROCONTROLLER
VM1AT-R1 INDUSTRIAL MICROCONTROLLER WARNING T avid permanent damage t integrated circuits yu may take precautins t discharge any static electricity frm yur bdy befre handling them. ASSEMBLY INSTRUCTIONS
More informationFlash Image Rotator Web Part
Flash Image Rtatr Web Part User Guide Cpyright 2007 Data Springs Inc. All rights reserved. Table f cntents: 1 INTRODUCTION...3 2 INSTALLATION PROCEDURE...4 2.1 After installatin ntes:...5 2.2 Trubleshting...6
More informationSolarEdge Built-in Revenue Grade Meter Troubleshooting
SlarEdge Built-in Revenue Grade Meter Trubleshting Versin 1.0 Cntents Trubleshting Meter Cnnectin 3 Cmmunicatin Status Screen Trubleshting 3 Device Type and Prtcl are cnfigured incrrectly 3 Number f devices
More informationThis app uses callas pdftoolbox server as the imposition engine and consequently you have to have that program installed on your Switch server.
Autmatic impsitin Page 1/8 Autmatic impsitin Descriptin Autmatic impsitin will d the mst cmmn impsitins fr yur digital printer. It will autmatically d flders fr A5, A4 r US Letter page sizes in either
More informationUltracom for Apple ios (2.X.X >) Printable user manual
30.8.2018 Ultracm fr Apple ios (2.X.X >) Printable user manual Table f cntents 1. General... 3 1.1 General inf... 3 1.2 Ultracm subscriptin and additinal services... 3 1.3 Operatr settings... 3 1.4 General
More informationLCN Remote Control. Perfection. High-End Building Management. Remote Control
Remte Cntrl C 1992 YEARS 2017 High-End Building Management C Remte Cntrl 25 ISSEORFF KG Magdeburger Str.3 30880 Rethen/Germany Tel: +49 (0)5066 99 80 www.c.eu Remte Cntrl C-RR Infrared receiver with lens
More informationGANTOM iq AND iqx USER GUIDE
GANTOM iq AND iqx USER GUIDE The Gantm iq is the wrld s smallest gb prjectr with zm and fcus fr prfessinal lighting applicatins. The Gantm iqx features the same amazing ptics f the Gantm iq but adds integrated
More informationWireless wall transmitter, 1-gang with inscription space, Wireless wall transmitter, 3-gang with inscription space
Wireless wall transmitter, 1-gang with inscription space Order No. : 5331.. Wireless wall Order No. : 5333.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected
More informationFrequency Response of a BJT CE Amplifier
Frequency Respnse f a BJT CE Amplifier Run the experiment By clicking the arrw n the Tlbar. Chse values f C B & C C, C E & R C frm the crrespnding drp dwn menus. (Clicking the arrw n the right side f the
More informationApplication Note AN-2097 Evaluation Kit for the S7500 CW Tunable Laser
Applicatin Nte AN-2097 Evaluatin Kit fr the S7500 CW Tunable Laser 1 Intrductin The evaluatin kit is intended t facilitate testing f Finisar s S7500 widely tunable laser, S7610 Integrable Tunable Laser
More informationTroubleshooting Guide StarFire Satellite Changes
Trubleshting Guide StarFire Satellite Changes This guide is updated t reflect the sftware frm NavCm which is related t the StarFire satellite and frequency changes. The mst recent versin f sftware fr bth
More informationIntesisBox IS-IR-KNX-1i v1.0. User's Manual Issue Date: 06/2017 r1.0 eng
IntesisBx IS-IR-KNX-1i v1.0 User's Manual Issue Date: 06/2017 r1.0 eng IntesisBx KNX IR Universal AC Intesis Sftware S.L.U. 2017 All Rights Reserved. Infrmatin in this dcument is subject t change withut
More informationFPP POINT PROBE SOP
FPP-5000 Versin 1.0 2/20/2015 Page 1 f 9 FPP-5000 4-POINT PROBE SOP The VEECO FPP-5000 4-pint prbe simplifies the measurement f resistive prperties f semicnductr wafers and resistive films. The micrprcessr
More informationOperating manual wireless hand wheel HBG 220-RF
Operating manual wireless hand wheel HBG 220-RF Cntents 1. Descriptin... 2 2. Technical Data... 2 2.1 Hand terminal HBG220-RF... 2 2.2 Access pint HBG 220-AP... 2 2.3 Charging statin... 2 2.4 System timing...
More informationRZ251W. Remote Sensing & Zoning Installation Guide. Quick Reference. Wireless Range
Remte Sensing & Zning Installatin Guide Pr Technlgies P.O. Bx 3377 Springfield, MO 65804 Tll ree : 888-776-47 Web: www.priaq.cm Hurs f Operatin: M- 9AM - 6PM Eastern Table f Cntents Table f Cntents Quick
More informationSeeGull CW Transmitter User Guide
SeeGull CW Transmitter User Guide Rev. E PCTEL 1 SeeGull CW Transmitter User Guide Dcument Number: 100103-00 Revisin E Octber 2018 Restrictins: This dcument cntains prprietary infrmatin that is prtected
More informationMartel LC-110H Loop Calibrator and HART Communications/Diagnostics
Martel LC-110H Lp Calibratr and HART Cmmunicatins/Diagnstics Abstract Martel Electrnics Crpratin This white paper describes the basic functins f HART cmmunicatins and the diagnstic capability f the Martel
More informationCB-030S Circuit Board
CB-030S Circuit Bard Designed fr use with the high trque PM486FH (up t 7A) Adjustable acceleratin and deceleratin time (0 t 2.5s) Stable speed peratin Switch fr manual r autmatic recvery f the thermal
More informationAF4000 MOD-1 OEM Production Line Troubleshooting Guide
Revisin 0: Initial dcument creatin, 9/2006, M. Rgers AF4000 MOD-1 OEM Prductin Line Trubleshting Guide If erratic system behavir is bserved that cannt be reslved by the methds utlined belw, ensure that
More informationGANTOM iq AND iqx USER GUIDE
GANTOM iq AND iqx USER GUIDE The Gantm iq is the wrld s smallest gb prjectr with zm and fcus fr prfessinal lighting applicatins. The Gantm iqx features the same amazing ptics f the Gantm iq but adds integrated
More informationService Update 7. PaperStream IP (TWAIN x64) for SP Series. change history. Version Version Version
PaperStream IP (TWAIN x64) fr SP Series change histry Service Update 7 Versin 1.46.0.5900 Crrected issue: 1. Minr errrs have been mdified. Versin 1.46.0.5775 New feature: 1. SP-1425 is newly supprted.
More informationManual Zeiss Axio Zoom.V16 microscope and ZEN 2 Pro software
Manual Zeiss Axi Zm.V16 micrscpe and ZEN 2 Pr sftware 15-9-2015 Fred Hartjes EMS 3 Caxial illum. Ring illum. Starting up Pwer n Actuate the knb n the EMS 3 cntrl unit Switch n the caxial illuminatin Switch
More informationSVT Tab and Service Visibility Tool Job Aid
Summary This Jb Aid cvers: SVT Tab Overview Service Visibility Tl (SVT) Area Overview SVT Area: Satellite Mdem Status (Frm Mdem) Clumn SVT Area: Satellite Mdem Status (Frm SMTS) Clumn SVT Area: Prvisining
More informationIntesisBox PA-RC-KNX-1i v1.2
IntesisBx PA-RC-KNX-1i v1.2 User's Manual Issue Date: 08/2015 r1.2 eng IntesisBx KNX Panasnic AC (FS / FSM) Intesis Sftware S.L. 2015 All Rights Reserved. Infrmatin in this dcument is subject t change
More informationUser Guide. ACC Mobile 3 Preview App for ios
User Guide ACC Mbile 3 Preview App fr ios 2017, Avigiln Crpratin. All rights reserved. AVIGILON, the AVIGILON lg, AVIGILON CONTROL CENTER, ACC, and TRUSTED SECURITY SOLUTIONS are trademarks f Avigiln Crpratin.
More informationNanoDrop One/One C Printing
MARK S100 INSTRUCTIONS NanDrp One/One C NanDrp One/One C Printing Fr use with versin 1.4 f lcal cntrl sftware All Therm Scientific NanDrp One/One C instruments with versin 1.4 f lcal cntrl sftware can
More informationDynaRound Hatch Guard System Installation Instructions
DynaRund Hatch Guard System Installatin Instructins Estimated Installatin Time: Man Crew, 0-90 Minutes The DynaRund Hatch Guard System is designed t prtect all rftp hatch entry and exit pints. This nn-penetrating
More informationInstallation hole (4.2mm) Push. Ambient daylight threshold. 8 hours manual on
STPSENSOR fr STRIP Mdel: STPSENSOR Infrared remte receiver Remte Cntrl (SENSORRC) sld separately Sensr antenna Buzzer Detectin area LED indicatin. Daylight threshld Stand-by perid 6. 9. 0 SYNC SYNC N L
More informationFIRMWARE RELEASE NOTES. Versions V2.0.0 to V Model HDL-32E. High Definition LiDAR Sensor
FIRMWARE RELEASE NOTES Versins V2.0.0 t V2.2.21.0 Mdel HDL-32E High Definitin LiDAR Sensr HDL-32E Firmware Release Ntes Page 2 Fr all new features and changes, refer t the dcumentatin that accmpanies the
More informationUpgrading to PlanetPress Suite Version 5
Upgrading t PlanetPress Suite Versin 5 Creatin date: September 2, 2005 Revisin date: June 14, 2006 Table f Cntents System Requirements... 4 Imprtant Cnsideratins... 4 Knwn Issues... 6 Prcedure t imprt
More informationUsing the Laser Cutter
Using the Laser Cutter Prerequisites Befre yu will be allwed t use the laser cutter, yu must cmplete these three steps: 1. Yu must have cmpleted the Laser Cutter training at Cyberia 2. Yu must schedule
More informationIntesisBox TO-RC-KNX-1i v1.3
IntesisBx TO-RC-KNX-1i v1.3 User's Manual Issue Date: 12/2015 r1.2 eng IntesisBx KNX Tshiba AC Digital Inverter & VRF lines Intesis Sftware S.L. 2015 All Rights Reserved. Infrmatin in this dcument is subject
More informationDry Contact Sensor DCS15 User Manual
Dry Cntact Sensr DCS15 User Manual Help Versin updated till firmware 404i / SP456 Cpyright 2012, AKCess Pr C., Ltd.. Intrductin / What is a Dry Cntact Sensr The Dry Cntact sensr r DCS15 is a simple cnnectin
More information4 wires. AUDIO & VIDEO TERMINALS for TL door phone systems User manual. Audio. 7" Videoadvanced. 7" Video
4 wires Audi AUDIO & VIDEO TERMINALS fr TL dr phne systems User manual 3.5" Vide 7" Vide 7" Videadvanced 0 Cntents 1 Safety instructins 2 Descriptin f the audi-vide terminals 3 Functins f the audi-vide
More informationThe WHO e-atlas of disaster risk for the European Region Instructions for use
The WHO e-atlas f disaster risk fr the Eurpean Regin Instructins fr use 1 Last Update: June 2011 Cntents 1. Basic system requirements... 3 2. Structure f the WHO e-atlas... 4 2.1. Main menu... 4 2.1.1.
More informationTUTORIAL I ECE 555 CADENCE SCHEMATIC SIMULATION USING SPECTRE
TUTORIAL I ECE 555 CADENCE SCHEMATIC SIMULATION USING SPECTRE Cadence Virtus Schematic editing prvides a design envirnment cmprising tls t create schematics, symbls and run simulatins. This tutrial will
More informationMobile LightSync Link App Programing Guide Revision 2
Mbile LightSync Link App Prgraming Guide Revisin 2 Overview: The Mbile LightSync Link App emulates LightSync input devices used t cntrl ILC relays and dimmer utputs frm an Andrid r Apple mbile device.
More informationThis Help system requires Internet Explorer 5 or later. It may not be displayed properly by earlier versions of Internet Explorer.
Intrductin Ntes This Help system requires Internet Explrer 5 r later. It may nt be displayed prperly by earlier versins f Internet Explrer. The appearance f the Wireless Panel sftware screenshts used in
More informationSupport Subscribers call
Prduced by Cmputer Helper Publishing (CHP). We hpe this sftware makes the tasks f Church administratin easier and mre efficient. Any questins that cannt be answered by these help files shuld be directed
More informationSet up and use your Beats X earphones
Set up and use yur Beats X earphnes Here's everything yu need t knw t make the mst f yur Beats X earphnes. Turn n The pwer buttn is n the cable beneath the right earphne. Press and hld the buttn fr 1 secnd
More informationSARAD GmbH Tel.: 0351 / Wiesbadener Straße 10 FAX: 0351 / Dresden Internet:
SARAD GmbH Tel.: 0351 / 6580712 Wiesbadener Straße 10 FAX: 0351 / 6580718 01159 Dresden e-mail: supprt@sarad.de GERMANY Internet: www.sarad.de APPLICATION NOTE AN-001_EN The Installatin f autnmus instrumentatin
More informationUSER S AND MAINTENANCE MANUAL
ENGLISH USER S AND MAINTENANCE MANUAL www.icaretnmeter.cm 1 Icare TONOVET tnmeter TV01 manual English TONOMETER Icare TONOVET tnmeter TV01 INSTRUCTION MANUAL v.2.1 14/09 EN Cpyright 2014 Icare Finland
More informationMaxon Motor & Motor Controller Manual
Maxn Mtr & Mtr Cntrller Manual Nte: This manual is nly fr use fr the Maxn mtr and cntrller utlined belw. This infrmatin is based upn the tutrial vides fund nline and thrugh testing. NOTE: Maximum Permitted
More informationOPERATING FEATURES & FUNCTIONS
OPERATON T stp an peratin at any time Press and hld the Start Key until the cntrl beeps fr tw secnds, indicating the peratin has been cancelled. The ven will remain in a pwer-n state. T turn ven cntrl
More informationMWL-MT10DX Turbo Ace Semi-Automated Tungsten Electrode Grinder
MWL-MT10DX Turb Ace Semi-Autmated Tungsten Electrde Grinder Operatins Guide 2 Table f Cntents Technical Specificatins 2 Parts Diagram 3 Grinding Instructins 4 Adjusting Preset Grinding Time 5 Adjusting
More informationEthernet Gateway User Manual
Summer 17 Ethernet Gateway Table f Cntents INTRODUCTION 3 AT A GLANCE 4 ETHERNET GATEWAY SETUP VIA DHCP 5 JACKS, BUTTONS, AND PORTS 6 TROUBLESHOOTING THE ETHERNET GATEWAY 7 LED INDICATOR LIGHTS 7 NO READINGS
More informationStandard Operating Procedure for SEM3 (ThermoFisher / FEI Apreo)
Standard Operating Prcedure fr SEM3 (ThermFisher / FEI Apre) Befre beginning, ensure yu have an active reservatin fr SEM3 in CreResearch@Duke Lading a Sample: If Sample Exchange Windw is nt pen, click
More informationSwitch to Save Program. Frequently Asked Questions
Switch t Save Prgram Frequently Asked Questins Prject Partners Invlved Bendig Bank has partnered with Energy Makevers t create the Switch t Save prgram. Envirnment & Sustainability Trudy Ellery, Head f
More informationADS ECHO Qstart Quick Reference Guide. 340 The Bridge Street, Suite 204 Huntsville, Alabama (256)
ADS ECHO Qstart Quick Reference Guide December 2016 QR 775033 A0 340 The Bridge Street, Suite 204 Huntsville, Alabama 35806 (256) 430-3366 www.adsenv.cm 2 ADS ECHO Qstart Quick Reference Guide 2016 ADS
More informationSpecification for a communicating Panelboard system to monitor, control and maintain LV electrical installations
Specificatin fr a cmmunicating Panelbard system t mnitr, cntrl and maintain LV electrical installatins A system fr: - Mnitring the prtectin and cntrl devices in an electrical installatin and prviding the
More informationApplication for Drive Technology
Applicatin fr Drive Technlgy MICROMASTER 4 Applicatin Descriptin Warranty, Liability and Supprt 1 Warranty, Liability and Supprt We d nt accept any liability fr the infrmatin cntained in this dcument.
More informationRDM3-P Paper Moisture Meter. MANUAL Version 1.0 Rev 02/13
RDM3-P Paper Misture Meter MANUAL Versin 1.0 Rev 02/13 DELMHORST EUROPE TITANIUMLAAN 100 NL 5221 CK s-hertogenbosch THE NETHERLANDS inf@delmhrst.eu www.misturemetersdelmhrst.cm +31 (0)73 6395080 TABLE
More informationDocumentation of the PIC32 Pin Finder
App. Versin: 1.1.1.120 Dcument Versin: 1.0 Dcument Create date: 2009-10-16 Dcument Update: 2009-10-19 22:37 Authr: B Gärdmark Cmpany: Spectrn System Develpment AB WEB: www.spectrn.us Cpyright 2009 All
More informationDamocles 2404i Manual
Damcles 2404i Inputs 1 8 Each blue terminal is shared by tw inputs. POWER 12V supply (+U / GND) ETHERNET Link & Activity Inputs 17 24 Each blue terminal is shared by tw inputs. Cnfiguratin Default: DIP1=
More informationDry Contact Sensor
www.akcp.cm Dry Cntact Sensr Intrductin The Dry Cntact sensr is a simple cnnectin t burglar alarms, fire alarms r any applicatin that requires mnitring by the unit. Dry cntact sensrs are user definable
More informationTable of Contents. ilab Solutions: Core Facilities Core Usage Reporting
Revisin Date: 12/31/2012 Table f Cntents 1. Institutin, Cre Facility and Lab Administratin Reprting Overview...2 2. Hw d I access ilab Reprts?...3 3. What is the General Functinality fr ilab Reprting?...6
More informationAPPLICATION NOTE Sales & Application DEWESoft Slovenia
Sales & Applicatin DEWESft Slvenia Abstract: This applicatin nte shws a measurement with DEWESft sund pwer measurement system and GRAS 67HA Hemisphere. The bject under test was a standard ntebk, the measurement
More informationDOEPFER. CV/Gate-Keyboard A-100CGK. User s Guide.
DOEPFER CV/Gate-Keybard A-100CGK User s Guide www.depfer.cm OPERATING AND SAFETY INSTRUCTIONS Please fllw the given instructins fr use f the instrument because this will guarantee crrect instrument peratin.
More information