SolarEdge. SolarEdge Electricity Meter Installation Guide. For North America Version 1.0

Size: px
Start display at page:

Download "SolarEdge. SolarEdge Electricity Meter Installation Guide. For North America Version 1.0"

Transcription

1 SlarEdge SlarEdge Electricity Meter Installatin Guide Fr Nrth America Versin 1.0

2 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval system r transmitted, in any frm r by any means, electrnic, mechanical, phtgraphic, magnetic r therwise, withut the prir written permissin f SlarEdge Inc. The material furnished in this dcument is believed t be accurate and reliable. Hwever, SlarEdge assumes n respnsibility fr the use f this material. SlarEdge reserves the right t make changes t the material at any time and withut ntice. Yu may refer t the SlarEdge web site ( fr the mst updated versin. All cmpany and brand prducts and service names are trademarks r registered trademarks f their respective hlders. Patent marking ntice: see The general terms and cnditins f delivery f SlarEdge shall apply. The cntent f these dcuments is cntinually reviewed and amended, where necessary. Hwever, discrepancies cannt be excluded. N guarantee is made fr the cmpleteness f these dcuments. The images cntained in this dcument are fr illustrative purpses nly and may vary depending n prduct mdels. FCC Cmpliance This equipment has been tested and fund t cmply with the limits fr a Class B digital device, pursuant t part 15 f the FCC Rules. These limits are designed t prvide reasnable prtectin against harmful interference in a residential installatin. This equipment generates, uses and can radiate radi frequency energy and, if nt installed and used in accrdance with the instructins, may cause harmful interference t radi cmmunicatins. Hwever, there is n guarantee that interference will nt ccur in a particular installatin. If this equipment des cause harmful interference t radi r televisin receptin, which can be determined by turning the equipment ff and n, yu are encuraged t try t crrect the interference by ne r mre f the fllwing measures: Rerient r relcate the receiving antenna. Increase the separatin between the equipment and the receiver. Cnnect the equipment int an utlet n a circuit different frm that t which the receiver is cnnected. Cnsult the dealer r an experienced radi/tv technician fr help. Changes r mdificatins nt expressly apprved by the party respnsible fr cmpliance may vid the user s authrity t perate the equipment. SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

3 Cntents Cntents Disclaimers 1 Imprtant Ntice 1 FCC Cmpliance 1 Cntents 2 HANDLING AND SAFETY INSTRUCTIONS 3 Safety Infrmatin 3 Chapter 1: Intrductin 4 Terminlgy 4 The SlarEdge Electricity Meter 5 Meter Cnnectin Optins 6 Chapter 2: Meter Installatin 7 Installatin Guidelines 7 Installing and Cnnecting the Meter 7 Chapter 3: SlarEdge Device Cnfiguratin 12 Appendix A: Trubleshting Meter Cnnectin 15 Cmmunicatin Status Screen Trubleshting 15 Device Type r Prtcl are cnfigured incrrectly 15 Number f devices is nt displayed 15 Meter Status Screen Trubleshting 15 <OK> is nt displayed 16 An errr message is displayed 16 Ttal [Wh] value is nt advancing 16 Meter Status LEDs 17 Pwer Status LEDs 17 Mdbus Cmmunicatin LEDs 18 Appendix B: Installing Tw Meters 19 Cnnecting Tw Meters 19 Cnfiguring Dual-meter Cnnectin 19 Verifying Meter Cnnectin 20 Trubleshting Dual-meter Cnnectin 21 Cmmunicatin Status Screen Trubleshting 21 Device Type r Prtcl are cnfigured incrrectly 21 Number f devices is lwer than cnfigured r nt displayed 21 Meter Status Screen Trubleshting 21 Appendix C: Meter Infrmatin Displayed in the Mnitring Prtal 22 Appendix D: Meter Technical Specificatins 23 Appendix E: External Lightning Prtectin Cnnectin 24 2 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

4 HANDLING AND SAFETY INSTRUCTIONS During installatin, testing and inspectin, adherence t all the handling and safety instructins is mandatry. Failure t d s may result in injury r lss f life and damage t the equipment. Safety Infrmatin The fllwing safety symbls are used in this dcument. Familiarize yurself with the symbls and their meaning befre installing r perating the system. WARNING! Dentes a hazard. It calls attentin t a prcedure that, if nt crrectly perfrmed r adhered t, culd result in injury r lss f life. D nt prceed beynd a warning nte until the indicated cnditins are fully understd and met. Dénte un risque: il attire l'attentin sur une pératin qui, si elle n'est pas faite u suivi crrectement, purrait causer des blessures u un danger de mrt. Ne pas dépasser une telle nte avant que les cnditins requises sient ttallement cmprises et accmplies. CAUTION! Dentes a hazard. It calls attentin t a prcedure that, if nt crrectly perfrmed r adhered t, culd result in damage r destructin f the prduct. D nt prceed beynd a cautin sign until the indicated cnditins are fully understd and met. Dénte un risque: il attire l'attentin sur une pératin qui, si elle n'est pas faite u suivi crrectement, purrait causer un dmmage u destructin de l'équipement. Ne pas dépasser une telle nte avant que les cnditins requises sient ttallement cmprises et accmplies. NOTE Dentes additinal infrmatin abut the current subject. IMPORTANT SAFETY FEATURE Dentes infrmatin abut safety issues. HANDLING AND SAFETY INSTRUCTIONS SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

5 Chapter 1: Intrductin Chapter 1: Intrductin Terminlgy The fllwing terms are used in this dcument: Exprt: The pwer injected t the grid. Imprt: The pwer purchased frm the grid. Exprt/ Imprt meter: A meter that is installed at the grid cnnectin pint and reads the energy/pwer exprted/imprted t/frm the grid. Cnsumptin: The pwer cnsumed by the site. Cnsumptin meter: A meter that is installed at the lad cnsumptin pint and reads the energy/pwer cnsumed by the site. Self-cnsumptin: The PV pwer cnsumed by the site and nt fed int the grid. Prductin: The PV pwer prduced by the PV system. Prductin meter: A meter that is installed at the inverter utput r in the inverter (a built-in revenue grade meter) and reads the energy/pwer prduced by the PV system. Figure 1: Terminlgy 4 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

6 The SlarEdge Electricity Meter The SlarEdge meter enables measuring the pwer and energy f the phtvltaic (PV) system. The meter is used by the inverter fr the fllwing applicatins: Cnsumptin mnitring Exprt limitatin StrEdge Smart Energy Management n-grid applicatins The meter is built int an enclsure and requires tw Current Transfrmers (CTs; available frm SlarEdge). Chapter 1: Intrductin The SlarEdge inverter r the Cntrl and Cmmunicatin Gateway (CCG) reads the exprted pwer frm a meter installed at the grid cnnectin pint r reads the cnsumptin frm a meter installed at the lad cnsumptin pint. Figure 2: Typical installatin with exprt meter Figure 3: Typical installatin with cnsumptin meter SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

7 Meter Cnnectin Optins Meter Cnnectin Optins In a single inverter system, the meter is cnnected directly t the inverter. If yur inverter has a built-in revenue grade meter (RGM; the inverter is referred t a revenue grade inverter), yu can cnnect an external meter n the same bus as the RGM (available frm SlarEdge). Figure 4: Single-inverter cnnectin In a multiple inverter system, tw ptins are available: The meter is cnnected t the RS485 prt f ne f the inverters. In this case, as the inverter's RS485 prt is ccupied by the meter, use an RS485 Expansin Kit (available frm SlarEdge) r ZigBee cmmunicatin between the inverters. The meter is cnnected t ne f the RS485 prts f a CCG. The CCG s secnd RS485 prt can be used t create an RS485 bus fr cmmunicatin between the inverters. This ptin is illustrated in Figure 5. Figure 5: Multi-inverter cnnectin with CCG and meter 6 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

8 Chapter 2: Meter Installatin Chapter 2: Meter Installatin The meter is cnnected t the inverter using RS485. Installatin Guidelines AC wire specificatins: 1.3 t 2.0 mm diameter / AWG stranded wire, 600 V, type THHN, MTW, r THWN. RS485 wiring specificatins: Cable type: Min. 3-wire shielded twisted pair (a 4-wire cable may be used) Wire crss-sectin area: mm²/ AWG (a CAT5 cable may be used) NOTE If using a cable lnger than 10 m/33 ft in areas where there is a risk f induced vltage surges by lightning, it is recmmend t use external surge prtectin devices. Fr details refer t External Lightning Prtectin Cnnectin n page 24. If grunded metal cnduit are used fr ruting the cmmunicatin wires, there is n need fr a lightning prtectin device. The meter is cnsidered permanently cnnected equipment and requires a discnnect means (circuit breaker, switch, r discnnect) and vercurrent prtectin (fuse r circuit breaker). The meter draws 10-30mA, therefre the rating f any switches, discnnects, fuses, and/ r circuit breakers is determined by the wire gauge, the mains vltage, and the current interrupting rating required. The switch, discnnect, r circuit breaker must be lcated near the meter and be easily perated. Use circuit breakers r fuses rated fr 20A r less. Use gruped circuit breakers when mnitring mre than ne line. The circuit breakers r fuses must prtect the mains terminals labeled L1, L2, and L3. In the rare cases where neutral has vercurrent prtectin, the vercurrent prtectin device must interrupt bth neutral and the ungrunded cnductrs simultaneusly. The circuit prtectin / discnnect system must meet all natinal and lcal electrical cdes. Installing and Cnnecting the Meter Munt the meter n a wall r ple using the supplied bracket. T munt the meter: 1. Install the bracket with the semi-circles facing dwn, as shwn belw. Verify that the bracket is firmly attached t the munting surface. Figure 6: Munting bracket SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

9 Installing and Cnnecting the Meter 2. Lsen the 4 Allen screws f the meter enclsure and remve the cver. Figure 7: Meter frnt view withut cver 3. Carefully mve the terminal blck end-stps t the sides f the meter and remve the terminal blcks. 4. Open ne r mre cnduit knckuts accrding t the cnduits used in the installatin: Open the required knckut(s), each with tw sizes: ¾'' and 1'', taking care nt t interfere with any f the internal cmpnents. A Unibit drill may be used. CAUTION! Use nly knckuts lcated at the bttm, back and sides f the enclsure. Opening the tp knckuts may damage the prtectin rating f the enclsure. Figure 8: Meter - rear view 5. Munt the meter: Attach the meter enclsure back brackets t the munted bracket using the fur supplied screws. Tighten the screws with a trque f 9 N*m / 6.6 lb*ft. T install the CTs: 1. Turn ff AC pwer befre clamping n current transfrmers. 2. Install the CTs arund the cnductr t be measured. Split-cre CTs can be pened fr installatin arund a cnductr. A nyln cable tie may be secured arund the CT t prevent accidental pening. 3. Install the CT with the arrw pinting t the grid fr cnsumptin r exprt measurement. 8 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

10 Chapter 2: Meter Installatin T wire the meter: If yu are cnnecting the meter t a revenue grade inverter, refer t Installing Tw Meters n page 19. Refer t the cnnectin diagram belw: NOTE Figure 9: Meter cnnectins Clamp the CT cnnected t L1 CT arund the wire cnnected t ØL1. Clamp the CT cnnected t L2 CT arund the wire cnnected t ØL2. 1. Verify that pwer is OFF befre making cnnectins. 2. Insert a grunding cable thrugh the apprpriate cnduit and the knckut that was pened and cnnect it frm Pin 10 f the 10-pin terminal blck t the grunding terminal (bus-bar) at the bttm f the meter enclsure. 3. Cnnect the AC side wires (meter input) using the 10-pin terminal blck: a. Insert the wires thrugh the apprpriate cnduit and the knckut that was pened. b. Lsen the apprpriate screws n the 10-pin terminal blck. c. Cnnect each AC wire t the apprpriate screw terminal (pins 6, 4). Verify that the lines match the symbls printed n the meter frnt label. d. Cnnect grund t pin 10 and neutral t pin 8. e. Tighten the screws making sure the wires are fully inserted and cannt be pulled ut easily. f. Insert the 10-pin terminal blck int the scket n the meter making sure it is fully seated in the meter. 4. Cnnect the CT wires t the 6-pin terminal blck: a. Insert the wires thrugh the apprpriate cnduit and the knckut that was pened. b. Cnnect the black and white wires accrding t the dts printed n the label: White t L1/L2 white (pins 1/3), and black t L1/L2 black (pins 2/4). c. Insert the 6-pin terminal blck int the scket n the meter making sure it is fully seated in the meter 5. Cnnect the RS485 twisted pair cable t the 4-pin terminal blck f the meter: a. Insert the wires thrugh the apprpriate cnduit and the knckut that was pened. b. Cnnect the wires t the A+ and B- terminals, and cnnect the shield t the G terminal. c. Insert the 4-pin terminal blck int the scket n the meter making sure it is fully seated in the meter 6. Return the terminal blck end-stps t the sides f the meter. SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

11 Installing and Cnnecting the Meter T cnnect the meter t the inverter r CCG: 1. If cnnecting t an inverter, remve the seal frm ne f the penings in cmmunicatin gland #2 at the bttm f the inverter and insert the RS485 wires frm the meter thrugh the pening. Figure 10: Cmmunicatin glands 2. Prepare t cnnect t ne f the available RS485 prts f the device, as shwn belw: Inverter RS pull ut the 9-pin RS485 cnnectr lcated n the cmmunicatin bard. Figure 11: Inverter RS485 cnnectr Inverter RS485 Expansin mdule - pull ut the 3-pin cnnectr Figure 12: Inverter RS485 Expansin mdule CCG - use ne f the 3-pin cnnectrs supplied with the CCG. Cnnect it t the RS485-2 cnnectin n the CCG. Figure 13: CCG RS485 cnnectr 10 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

12 Chapter 2: Meter Installatin 3. Cnnect the wires as shwn belw: Figure 14: Meter RS485 cnnectins 4. If the SlarEdge device is at the end f the RS485 bus, terminate as fllws: Inverter - Terminate by switching a terminatin DIP-switch inside the inverter t ON (tp psitin). The switch is lcated n the cmmunicatin bard and is marked SW7. CCG - Terminate by switching the SW2 terminatin DIP-switch t ON. Figure 15: RS485 terminatin switch SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

13 Chapter 3: SlarEdge Device Cnfiguratin Chapter 3: SlarEdge Device Cnfiguratin This sectin describes basic cnfiguratin f SlarEdge devices (inverter/ccg) fr using a meter. In additin, cnfiguratin specific t the applicatin being used is required in sme cases. Refer t the fllwing dcuments: Exprt Limitatin - nte_na.pdf Cnsumptin and Prductin Mnitring - nte.pdf StrEdge Smart Energy Management ff-grid applicatins - Fr cnfiguring tw cnnected meters refer t Installing Tw Meters n page 19. T cnfigure the SlarEdge device: Use the fur user buttns t cntrl the LCD panel menus: Esc: Ges t the beginning f the currently entered parameter r t the previus menu. Up (1) and Dwn (2): Mves the cursr (>) t the relevant menu ptin. Enter (3): Used t select an ptin 1. Verify that the device ON/OFF switch is OFF. 2. Turn ON the AC switch f the main circuit bard. WARNING! ELECTRICAL SHOCK HAZARD. D nt tuch uninsulated wires when the inverter cver is remved. RISQUE D ÉLECTROCUTION, ne tuchez pas les fils nn islés lrsque le cuvercle de l'nduleur est retiré. 3. Press the Enter (3) buttn fr at least five secnds. The fllwing message is displayed: P l e a s e e n t e r P a s s w r d * * * * * * * * 4. Use the three right mst buttns (Up-1, Dwn-2 and Enter-3) t type in the fllwing default passwrd: Scrll t the Cmmunicatin menu and select RS485-X Cnf (X represents the actual RS485 prt t which the electricity meter is cnnected: 1 r E fr the inverter; 1 r 2 r E fr the CCG). The fllwing screen is displayed: D e v i c e T y p e < S E > P r t c l < M > D e v i c e I D < 1 > S l a v e D e t e c t < # > S l a v e L i s t < # > 12 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

14 Chapter 3: SlarEdge Device Cnfiguratin 6. Select Device Type. the fllwing screen is displayed: S l a r E d g e < M > N n - S E L g g e r < S > R e v e n u e M e t e r < M > M u l t i - d e v i c e s < M > N n e 7. Select Revenue Meter, the fllwing screen is displayed: D e v i c e T y p e < M T R > P r t c l < W N > D e v i c e I D < 1 > C T R a t i n g < 0 > M e t e r F u n c. < N n e > 8. Cnfigure the meter parameters as fllws: Select Prtcl è WattNde. Select Device ID: 2 Set the CT rating t the value that appears n the CT: CT Rating è <xxxxa>. The default is 5 Amperes. If the displayed rating is 0 r yu cannt change the value, there is n cmmunicatin with the meter. Check that the AC pwer t the meter is n. Select Meter Func. and select ne f the functinality ptins, accrding t the installed meter specificatins and lcatin. E x p r t + I m p r t E x p r t C n s u m p t i n P r d u c t i n I m p r t N n e Exprt+Imprt: The meter is installed at the grid cnnectin pint and reads pulses frm bth directins - exprt and imprt energy. Exprt: The meter is installed at the grid cnnectin pint and reads the exprt energy. Cnsumptin: The meter is installed at the lad cnsumptin pint and reads the energy cnsumed by the site. Prductin: The meter is installed at the inverter utput and reads the energy prduced by the inverter. Imprt: The meter is installed at the grid cnnectin pint and reads the imprt energy. Nne: N reading The selected ptin is displayed in the RS485 Cnf screen as <E+I>, <E>, <Cns>, <Prd>, <I>, <Nne>. 9. Exit Setup mde. NOTE Calculated meter readings, such as self-cnsumptin, are calculated using the data measured by the meter and the inverters. Calculated meters are nly sent when Energy Manager is enabled (fr details refer t nte_na.pdf). SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

15 Chapter 3: SlarEdge Device Cnfiguratin T verify meter cnnectin: 1. Press the Enter buttn r the LCD external buttn until the Cmmunicatin status screen is displayed as shwn belw. This screen shws the number f external devices that cmmunicate n each prt, the device type, and the prtcl t which each prt was cnfigured. 2. Verify that the setting f the relevant RS485 prt is crrect and that the prt is cmmunicating with the meter. Fr example, if the meter is cnnected t the RS485-1 prt, the Cmmunicatin status screen shuld display the fllwing: w w w w w w w D e v P r t # # R S < M T R > < W N > < 1 > R S < > < - - > < - - > Z i g B e e < > < - - > < - - > Dev: the type f device cnfigured t this prt. MTR indicates a meter. Prt: the cmmunicatin prtcl ## = 1: Indicates that the cnnectin t the meter is successful. 3. Press the Enter buttn r the LCD external buttn until reaching the meter status screen shwing the ttal energy [Wh]. If there is mre than ne meter/functin, there is a status screen fr each ne. The fllwing is an example f an Exprt meter: E x p r t M e t e r S t a t u s : < O K / E r r r # > P w e r [ W ] : E n e r g y [ W h ] : x x x x x. x X X X X X. X Status: Displays OK if the meter is cmmunicating with the inverter. <Errr message>: If an internal meter errr ccurs, it will be displayed here. Refer t Trubleshting Meter Cnnectin n the facing page. Ttal [Wh]: Displays the accumulated lifetime energy f the meter. If the SlarEdge device is cnnected t the SlarEdge server this value will als be displayed in the mnitring prtal. T display the meter serial number: 1. Enter Setup mde and select Infrmatin. The fllwing screen is displayed: V e r s i n s E r r r L g W a r n i n g l g H a r d w a r e I D s 2. Select Hardware IDs. The fllwing is displayed shwing the ID f the inverter and any meter cnnected t it: I D F F F F 4 E R G M : SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

16 Appendix A: Trubleshting Meter Cnnectin SlarEdge revenue grade inverters have a built in Revenue Grade Meter (RGM). Fr trubleshting RGMs, refer t This sectin describes hw t trublesht meter-related installatin and perfrmance errrs. Cmmunicatin Status Screen Trubleshting The cmmunicatin status screen shuld display the fllwing: w w w w w w w w D e v P r t # # R S < M T R > < W N > < 1 > R S < > < - - > < - - > Z i g B e e < > < - - > < - - > Appendix A: Trubleshting Meter Cnnectin Device Type r Prtcl are cnfigured incrrectly If MTR (meter) is nt displayed as the device type (DEV), r WN (WattNde) is nt displayed as the Prt (prtcl), cnfigure the meter as fllws.: 1. Select CmmunicatinèRS485-x CnfèDevice Typeè Revenue Meter. 2. Select Cmmunicatin è RS485-x Cnf è Prtcl èwattnde. 3. Check that the Device ID under Cmmunicatin è RS485-x Cnf è Device ID is set t Select Revenue Meter è Meter Func. è Exprt+Imprt / Exprt / Imprt / Cnsumptin. Number f devices is nt displayed If <--> is displayed under the ## clumn in the Cmmunicatin status screen, the meter is nt cmmunicating with the inverter. Check the fllwing: The meter cnfiguratin is as described abve. There are n lse cnnectins at the inverter cnnectrs and at the meter, specifically the RS485 wiring. The wiring between the black 4-pin terminal blck n the meter and the RS485 terminal blck n the cmmunicatin bard is crrect, as shwn in Figure 9. Check fr water damage r sealing prblems: Inspect the entire cnduit run fr pssible pints f water penetratin, and fix leaks. Ensure that prper utdr rated cmpnents are used. Use a Vltmeter t measure the vltage n the meter 10-pin terminal blck. The L1 L2 line t line vltage shuld be Vac. Meter Status Screen Trubleshting P r d u c t i n M e t e r S t a t u s : < O K / E r r r > P w e r [ W ] : E n e r g y [ W h ] : x x x x x. x x x x x x. x SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

17 <OK> is nt displayed <OK> is nt displayed If <OK> is nt displayed in the Status line f the status screen shwn abve, the meter is nt cmmunicating with the inverter. Check the fllwing: There are n lse cnnectins at the inverter cmmunicatin bard and at the meter. The wiring between the black 4-pin terminal blck n the meter and the RS485 terminal blck n the cmmunicatin bard is crrect. Check fr water damage r sealing prblems: Inspect the entire cnduit run fr pssible pints f water penetratin, and fix leaks. Ensure that prper utdr rated cmpnents are used. An errr message is displayed If Cmm. Errr is displayed in the meter status screen, verify prper cnnectin f: The RS485 cables and cnnectrs The AC cnnectin f the meter If Errr 185 Meter Cmm. Errr message is displayed, cntact SlarEdge supprt. Ttal [Wh] value is nt advancing If the Ttal [Wh] value displays a steady value althugh the inverter is prducing pwer, check the fllwing: There are n lse cnnectins at the inverter cnnectrs and at the meter, specifically the AC wiring n the meter 10-pin cnnectr. The CT black and white cables are crrectly cnnected t the 6-pin cnnectr n the meter: White CT wire is cnnected t the L1/L2 white dt. Black CT wire is cnnected t the L1/L2 black dt. The L1/L2 cable passes thrugh the CT in the crrect directin (right t left), accrding t the arrw n the inside f the CT. Figure 16: Meter Cnnectin diagram Check fr water damage r sealing prblems: Inspect the entire cnduit run fr pssible pints f water penetratin, and fix leaks. Ensure that prper utdr rated cmpnents are used. 16 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

18 Appendix A: Trubleshting Meter Cnnectin Meter Status LEDs Pwer Status LEDs The three status LEDs n the frnt f the meter can help indicate crrect measurements and peratin. Nrmal peratin indicatins: LED clr Red At nrmal startup - when pwer is first applied, all the LEDs light up sequentially fr 1 sec. The fllwing table describes LED indicatins during nrmal peratin: Functin Flashing ON/OFF Indicatin Appears nly when the meter is cnnected at the grid cnnectin pint (CT directed twards the grid). Indicates exprt pwer measurement. Yellw Flashing Cmmunicatin OK Green Flashing ON/OFF ON fr >3 sec Abnrmal peratin indicatins: When the meter is cnnected at the grid cnnectin pint it indicates imprt pwer measurement (CT directed twards the grid). When the meter is cnnected at the lad cnnectin pint it indicates cnsumptin pwer measurement (CT directed twards the grid). When the meter is used fr prductin it indicates prductin pwer measurement (CT directed tward the inverter). N current flw (zer current) If all LEDs are ff the meter is nt perating. Perfrm all trubleshting steps starting with checking the physical cnnectins. The fllwing table describes additinal LED indicatins that require trubleshting and repair. LED clr Functin Indicatin Trubleshting Red Yellw ON fr >3 sec. Internal errr Cntact SlarEdge Supprt. Flashing ON/OFF Negative pwer fr the phase Flashing with green Vltage is t high fr this LED mdel Flashing with yellw LED ON fr >3sec. Flashing with red LED The line vltage is ut f range (Vac ±20%). Specifically, the vltage is t lw fr the meter t perate crrectly and the meter rebts repeatedly. Pwer line frequency is belw 45 Hz r abve 70 Hz. Vltage is t high fr this mdel If the meter is cnnected at the lad cnnectin pint r if the meter is used fr prductin metering, check fr reversed CTs, swapped CT wires, r CTs nt matched with the lines. Discnnect pwer immediately! Check the line vltages and the meter ratings. Verify that the vltage n the Vac screw terminals is within the range f ±20% f the nminal perating vltages printed in the white rectangle n the frnt label. Check fr the presence f high nise, fr example, the meter is t clse t an unfiltered variable frequency drive. Discnnect pwer immediately! Check the line vltages and the meter ratings. SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

19 Mdbus Cmmunicatin LEDs Mdbus Cmmunicatin LEDs The cmmunicatin LED is lcated at the upper left crner. The fllwing are indicatins f the LED light: LED clr Functin Indicatin Trubleshting Red Flashing ON Flashing with yellw LED An invalid packet: bad baud rate, bad CRC, nise, bad parity, etc. The address is set t zer: an invalid chice A pssible address cnflict (tw devices with the same DIP switch address). Yellw Flashing Valid packets addressed t different devices. N/A Green Flashing A valid packet addressed t this device N/A Check that the cmmunicatin wires are cnnected crrectly. Check that the Device ID is set t 2 in the RS485 Cnf screen. Check that the Device ID is set t 2 in the RS485 Cnf screen. 18 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

20 Appendix B: Installing Tw Meters This sectin describes cnnecting an external meter t an inverter equipped with a built-in Revenue Grade Meter (RGM), which is lcated in the Safety Switch. RS485 wiring is daisy-chained between the tw meters and the inverter. Cnnecting Tw Meters 1. Cnnect the external meter t the RGM as shwn in Figure 17: a. Rute the external meter wires thrugh ne f the Safety Switch cnduits (it is recmmended t use the DC side cnduits). b. Cnnect the external meter wires tgether with the RGM wires t the same screw terminals f the RGM RS485 terminal blck: Remve the RGM wires frm the terminals (nte the wire clr and lcatin). Twist the wires tgether and insert them int the terminal. Securely tighten the terminal screws. Appendix B: Installing Tw Meters Figure 17: Meters cnnectin t an RGM inverter 2. Terminate the SlarEdge device as described in Installing and Cnnecting the Meter n page 7. Cnfiguring Dual-meter Cnnectin The built-in RGM is pre-cnfigured as a prductin meter and its settings shuld nt be changed. Verify the pre-cnfigured parameters f the RGM and cnfigure the parameters f the external meter as described belw. 1. Enter Setup mde, scrll t the Cmmunicatin menu and select Cmmunicatin è RS485-x Cnf. The fllwing screen is displayed: D e v i c e T y p e < S E > P r t c l < M > D e v i c e I D < 1 > S l a v e D e t e c t < # > S l a v e L i s t < # > SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

21 Verifying Meter Cnnectin 2. Select Device Type. the fllwing screen is displayed: S l a r E d g e < M > N n - S E L g g e r < S > R e v e n u e M e t e r < M > M u l t i - d e v i c e s < M > N n e 3. Select Multi Devices. The fllwing screen is displayed: D e v i c e T y p e < M L T > M e t e r 1 < W N, 1 > M e t e r 2 < > M e t e r 3 < > 4. Select Meter 1. The fllwing is displayed fr the RGM: 5. Verify: D e v i c e T y p e < M T R > P r t c l < W N > D e v i c e I D < 1 > C T R a t i n g < 5 A > M e t e r F u n c. < P r d > Device Type è MTR Prtcl è WN Device ID è 1 CT Rating è 5A Meter Func.è Prd (prductin) 6. Select Meter 2 and cnfigure the external meter settings: Select Device Type è Revenue Meter Select Prtcl è WattNde Set Device ID: 2 Set the CT rating t the value that appears n the CT: CT Rating è <xxxxa>. The default is 5 Amperes. If the displayed rating is 0 r yu cannt change the value, there is n cmmunicatin with the meter. Check that the AC pwer t the meter is n. Select Meter Func.è Exprt/Imprt/Exprt+Imprt/Cnsumptin Verifying Meter Cnnectin 1. Press the Enter buttn r the LCD external buttn until the Cmmunicatin status screen is displayed as shwn belw. When tw meters are cnnected, a screen similar t the fllwing shuld appear: w w w w w w w D e v P r t # # R S < M L T > < 0 2 > < 0 2 > R S < > < - - > < - - > Z i g B e e < > < - - > < - - > Dev: The type f device cnfigured t this prt. MLT indicates multiple meters. Prt: The number f cnfigured meters. 20 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

22 ## : The number f cmmunicating meters. Fr dual meters it shuld display 2. If nt, refer t Trubleshting belw. 2. Press the Enter buttn r the LCD external buttn until reaching the Meter status screen shwing the ttal energy [Wh]. There is a status screen fr each meter functin. Fr example, fr an exprt+imprt meter and a prductin meter, there will be three status screens: fr exprt, imprt and prductin. The fllwing is an example f an exprt meter: E x p r t M e t e r S t a t u s : < O K > < E r r r M e s s a g e > T t a l [ W h ] : X X X X X X X Status: Displays OK if the meter is cmmunicating with the cmmunicatin bard. <Errr message>: If an internal meter errr ccurs, it will be displayed here. Refer t Trubleshting Meter Cnnectin n page 15. Ttal [Wh]: The amunt f Watts per hur f the designated meter. If the SlarEdge device is cnnected t the SlarEdge server this value will als be displayed in the mnitring prtal. Trubleshting Dual-meter Cnnectin Cmmunicatin Status Screen Trubleshting When tw meters are cnnected n the same RS485 bus, the fllwing shuld appear in the Cmmunicatin status screen: w w w w w w w w D e v P r t # # R S < M L T > < 0 2 > < 0 2 > R S < > < - - > < - - > Z i g B e e < > < - - > < - - > Device Type r Prtcl are cnfigured incrrectly If MLT (Multi) is nt displayed as the device type (DEV), r 2 is nt displayed as the number f meters under Prt (prtcl), cnfigure the meters as fllws: 1. Select Cmmunicatin è RS485-x Cnf è Device Type è Multi Devices. Select Device 1 r Device Select Cmmunicatin è RS485-x Cnf è Prtcl è WattNde. 3. Select Revenue Meter è Meter Func. è Prductin, Cnsumptin, Exprt, Imprt, r Exprt+Imprt. 4. Check that the Device ID under Cmmunicatin è RS485-x Cnf è Device ID is set t 1 r 2. Number f devices is lwer than cnfigured r nt displayed If <--> r <01> is displayed under the ## clumn in the Cmmunicatin status screen shwn abve, at least ne f the meters is nt cmmunicating with the inverter. Check the fllwing: The meter cnfiguratin is as described abve. There are n lse cnnectins at the inverter cnnectrs and at the meters, specifically the RS485 wiring. Meter Status Screen Trubleshting Refer t Meter Status Screen Trubleshting n page 15. Appendix B: Installing Tw Meters SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

23 Appendix C: Meter Infrmatin Displayed in the Mnitring Prtal Appendix C: Meter Infrmatin Displayed in the Mnitring Prtal If yur device is cnnected t the SlarEdge server, yu can view the meter s readings in the mnitring prtal. Verify that the meter type is set crrectly in the Admin page > Lgical Layut > Meter details: Figure 18: Setting the Meter details in the mnitring prtal Calculated meter readings (als referred t as "virtual meters"), such as self-cnsumptin, are calculated using the data measured by the meter and the inverters. The data frm the inverters and frm installed meters is displayed in the Dashbard and Charts tabs f the mnitring prtal. The displayed data depends n the meter(s) lcatin: grid cnnectin pint (exprt), r lad cnsumptin pint (cnsumptin). The fllwing tables detail the displayed infrmatin per meter lcatin. Exprt meter: Data Displayed in Mnitring Dashbard Displayed in Mnitring Charts Prductin a a Cnsumptin a(calculated) a(calculated) Self-cnsumptin a(calculated) a(calculated) Exprt X a Imprt X a Cnsumptin meter: Data Displayed Displayed in in Mnitring Mnitring Dashbard Charts Displayed in Mnitring Dashbard Displayed in Mnitring Charts Prductin a a a a Cnsumptin a a a a Selfcnsumptin a(calculated) a (calculated) Exprt X a (calculated) a(calculated) X a(calculated) a(calculated) Imprt X X X X 22 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

24 Appendix D: Meter Technical Specificatins Appendix D: Meter Technical Specificatins ELECTRICAL SERVICE SE-MTR S1 SE-MTR S1 UNITS Operating Vltage Range - Line t Line Vac AC Frequency 60 Hz Grids Supprted L1 / L2 / N / PE Pwer Cnsumptin (typ.) 1.2 W COMMUNICATION Supprted Cmmunicatin Interfaces RS485 Respnse time 1 sec Device ID (Mdbus) 2 ACCURACY (@ 77 F / 25 C, PF:0.7-1) 1% - 100% f Rated CT Current ±1 % CURRENT TRANSFORMERS Rated RMS current Dimensins (Internal ; External) STANDARD COMPLIANCE 0.8 x 0.8 ; 2.4 x 2.4 / 20 x 20 ; 61 x 61 Safety UL1741 INSTALLATION SPECIFICATIONS 1.26 x 1.83 ; 3.3 x 4.5 / 32 x 46.5 ; 83.4 x 114 in/mm Dimensins (HxWxD) 8.1 x 12.4 x 4.6 / x 316 x in / mm Weight 3.9 / 1.8 lb / gm Enclsure type High impact, ABS and/r ABS/PC plastic UL 94V-0, IEC FV-0 Operating Temperature Range -22 t +131 / -30 t + 55 F / C Relative Humidity (nncndensing) 5-90 % Prtectin Rating NEMA Type 3R Cnduit Entry Diameters 0.75 r 1/ 19 r 25 in / mm Munting Type Wall munt 1 Fr ther ratings cntact SlarEdge SlarEdge-SlarEdge Electricity Meter Installatin Guide MAN

25 Appendix E: External Lightning Prtectin Cnnectin Appendix E: External Lightning Prtectin Cnnectin Prtectin devices are mst ften installed frm each data line t the lcal earth grund, and shuld be selected t begin cnducting current at a vltage as clse t the system's nrmal cmmunicatin level as pssible, but never lwer. Fr RS485 cmmunicatin lines, the selected vltage rating is typically 6-8 V. Transient suppressrs shuld be installed as clse as pssible t the prt that is being prtected, and the user must prvide an extremely lw impedance cnnectin t the lcal earth grund f the SlarEdge device. This grund cnnectin is crucial fr prper suppressin device peratin. The grund cnnectin shuld be made using a heavy gauge wire and kept as shrt as pssible. If the cable between the SlarEdge device and the prtectin device must be lnger than 1m/ 3.3 ft., a cpper strap r a braided cable intended fr grunding purpses must be used fr the prtectin device t be effective. In additin t the high frequency nature f transients, extremely high current may flw. A prtective device with surge discharge ratings f In: 10kA 8/20μs and Imax: 20kA 8/20μs is recmmended. Varius lightning prtectin devices are available fr RS485 cmmunicatin lines. The diagram belw shws a cnnectin example using the ISKRA ZAŠČITE VM-RS 485 data prtcl prtectin device. A detailed datasheet can be fund at: Figure 19: Prtectin cnnectin 24 SlarEdge SlarEdge Electricity Meter Installatin Guide MAN

26

SolarEdge Built-in Revenue Grade Meter Troubleshooting

SolarEdge Built-in Revenue Grade Meter Troubleshooting SlarEdge Built-in Revenue Grade Meter Trubleshting Versin 1.0 Cntents Trubleshting Meter Cnnectin 3 Cmmunicatin Status Screen Trubleshting 3 Device Type and Prtcl are cnfigured incrrectly 3 Number f devices

More information

SolarEdge. Modbus Meter Installation Guide. Europe and APAC Version 1.0

SolarEdge. Modbus Meter Installation Guide. Europe and APAC Version 1.0 SlarEdge Mdbus Meter Installatin Guide Eurpe and APAC Versin 1.0 Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval system

More information

SolarEdge. StorEdge Interface Installation Guide. For the S1/S2 StorEdge Interface with LG Chem Batteries and Single Phase non-hd-wave Inverters

SolarEdge. StorEdge Interface Installation Guide. For the S1/S2 StorEdge Interface with LG Chem Batteries and Single Phase non-hd-wave Inverters SlarEdge StrEdge Interface Installatin Guide Fr the S1/S2 StrEdge Interface with LG Chem Batteries and Single Phase nn-hd-wave Inverters Fr Eurpe, APAC, Australia & Suth Africa Versin 1.4 Disclaimers Disclaimers

More information

SolarEdge. StorEdge Installation Guide. For Smart Energy Management using the StorEdge Interface. For Europe, APAC & South Africa. Version 1.

SolarEdge. StorEdge Installation Guide. For Smart Energy Management using the StorEdge Interface. For Europe, APAC & South Africa. Version 1. SlarEdge StrEdge Installatin Guide Fr Smart Energy Management using the StrEdge Interface Fr Eurpe, APAC & Suth Africa Versin 1.3 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights

More information

SolarEdge. Immersion Heater Controller Installation Guide. For Europe, APAC & South Africa Version 1.6

SolarEdge. Immersion Heater Controller Installation Guide. For Europe, APAC & South Africa Version 1.6 SlarEdge Immersin Heater Cntrller Installatin Guide Fr Eurpe, APAC & Suth Africa Versin 1.6 Cntents Cntents HANDLING AND SAFETY INSTRUCTIONS 2 Safety Symbls Infrmatin 2 Immersin Heater Cntrller Installatin

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Lad with min. 5 kg 405000090 405070090 INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main dimensins. 3. Parts included. 4. Installatin. 5. Adjusting the strke

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Lad: Min. 5 kg Max. 100 kg TS1000A TS700A INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main measures. 3. Parts included. 4. Installatin. 5. Adjusting the strke

More information

SolarEdge. Data Logger Installation Guide. For North America Version 1.1

SolarEdge. Data Logger Installation Guide. For North America Version 1.1 SlarEdge Data Lgger Installatin Guide Fr Nrth America Versin 1.1 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval

More information

Operating Instructions

Operating Instructions TC 60/8 THERMOCOMPUTER TC 60/8 temp / time s s temp / time k start stp Operating Instructins Cntents General Infrmatin...1 Security Advice...1 Firing Curves...1 Typical Firing Curves...2 Entering a Firing

More information

Dry Contact Sensor. Communications cable - RJ-45 jack to sensor using UTP Cat 5 wire. Power source: powered by the unit. No additional power needed.

Dry Contact Sensor. Communications cable - RJ-45 jack to sensor using UTP Cat 5 wire. Power source: powered by the unit. No additional power needed. Intrductin Dry Cntact Sensr The Dry Cntact sensr is a simple cnnectin t burglar alarms, fire alarms r any applicatin that requires mnitring by the unit. Dry cntact sensrs are user definable and can be

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Lad: Min. 5 kg Max. 100 kg TS1000A TS700A INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main measures. 3. Parts included. 4. Installatin. 5. Adjusting the strke

More information

Electrical devices may only be mounted and connected by electrically skilled persons.

Electrical devices may only be mounted and connected by electrically skilled persons. Order N. : 5323 02 Operating instructins 1 Safety instructins Electrical devices may nly be munted and cnnected by electrically skilled persns. Serius injuries, fire r prperty damage pssible. Please read

More information

SolarEdge. Installation Guide. For Europe, APAC, Australia & South Africa Version 3.3

SolarEdge. Installation Guide. For Europe, APAC, Australia & South Africa Version 3.3 SlarEdge Installatin Guide Fr Eurpe, APAC, Australia & Suth Africa Versin 3.3 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced,

More information

SolarEdge System Installation Guide

SolarEdge System Installation Guide SlarEdge System Installatin Guide Fr Eurpe, APAC and Suth Africa Versin 4.0 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred

More information

TC 60 THERMOCOMPUTER TC 60. prog. start stop. Operating Instructions

TC 60 THERMOCOMPUTER TC 60. prog. start stop. Operating Instructions TC 60 prg start stp THERMOCOMPUTER TC 60 h C/h C Operating Instructins Cntents General Infrmatin...1 Security Advice...1 Firing Curves...1 Typical Firing Curves...2 Entering a Firing Curve...2 Checing

More information

idcv Isolated Digital Voltmeter User Manual

idcv Isolated Digital Voltmeter User Manual www.akcp.cm idcv Islated Digital Vltmeter User Manual Help Versin updated till firmware SP446 Cpyright 2011, AKCess Pr Limited Prvided by fficial AKCP-Distributr Didactum https://www.didactum-security.cm/en/

More information

BV4115. RF Packet Transmitter. Product specification. February ByVac 2007 ByVac Page 1 of 5

BV4115. RF Packet Transmitter. Product specification. February ByVac 2007 ByVac Page 1 of 5 Prduct Specificatin Prduct specificatin. February 2007 ByVac 2007 ByVac Page 1 f 5 Prduct Specificatin Cntents 1. Dcument Versins... 2 2. Intrductin... 2 3. Features... 2 4. Battery Life... 2 5. Blck Diagram...

More information

Operating Instructions

Operating Instructions TC 40 THERMOCOMPUTER TC 40 start stp Operating Instructins Cntents General Infrmatin...1 Security Advice...1 Firing Curves...1 Typical Firing Curves...2 Entering a Firing Curve...2 Checing the Prgramme

More information

SolarEdge. Compact Residential Solution Installation Guide. For Europe, APAC,& South Africa Version 1.0

SolarEdge. Compact Residential Solution Installation Guide. For Europe, APAC,& South Africa Version 1.0 SlarEdge Cmpact Residential Slutin Installatin Guide Fr Eurpe, APAC,& Suth Africa Versin 1.0 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may

More information

Acceptance and verification PCI tests according to MIL-STD

Acceptance and verification PCI tests according to MIL-STD Acceptance and verificatin PCI tests accrding t MIL-STD-188-125 Bertrand Daut, mntena technlgy V1 - August 2013 CONTENTS 1. INTRODUCTION... 1 2. DEFINITIONS... 1 3. SCHEMATIC OF THE TEST SETUP WITH USE

More information

RiverSurveyor S5/M9 & HydroSurveyor Second Generation Power & Communications Module (PCM) Jan 23, 2014

RiverSurveyor S5/M9 & HydroSurveyor Second Generation Power & Communications Module (PCM) Jan 23, 2014 SnTek, a Xylem brand 9940 Summers Ridge Rad, San Dieg, CA 92121-3091 USA Telephne (858) 546-8327 Fax (858) 546-8150 E-mail: inquiry@sntek.cm Internet: http://www.sntek.cm RiverSurveyr S5/M9 & HydrSurveyr

More information

HANDLING AND SAFETY INSTRUCTIONS

HANDLING AND SAFETY INSTRUCTIONS Cntents Disclaimers 3 Imprtant Ntice 3 Emissin Cmpliance 3 Supprt and Cntact Infrmatin 4 Revisin Histry 5 Versin 1.1 (June 2018) 5 Versin 1.0 - initial release (June 2017) 5 HANDLING AND SAFETY INSTRUCTIONS

More information

Single Phase Inverter with compact technology. Installation Guide. For Europe, APAC,& South Africa Version 1.2

Single Phase Inverter with compact technology. Installation Guide. For Europe, APAC,& South Africa Version 1.2 Single Phase Inverter with cmpact technlgy Installatin Guide Fr Eurpe, APAC,& Suth Africa Versin 1.2 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument

More information

SolarEdge. Extended Power. Commercial Inverter. Installation Guide. For Europe, APAC,& South Africa Version 1.0

SolarEdge. Extended Power. Commercial Inverter. Installation Guide. For Europe, APAC,& South Africa Version 1.0 SlarEdge Extended Pwer Cmmercial Inverter Installatin Guide Fr Eurpe, APAC,& Suth Africa Versin 1.0 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument

More information

TROUBLESHOOTING GUIDE

TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE Dcument revisin 1.3 Last revised: December 6, 2017 Recn Wireless Blckage and Flw Mnitr Trubleshting Guide 2014-2017 Intelligent Agricultural Slutins All Rights Reserved. Recn Wireless

More information

LINE POWER SUPPLIES Low-Loss Supplies for Line Powered EnOcean Modules

LINE POWER SUPPLIES Low-Loss Supplies for Line Powered EnOcean Modules Lw-Lss Supplies fr Line Pwered EnOcean Mdules A line pwer supply has t ffer the required energy t supply the actuatr electrnic and t supply the EnOcean TCM/RCM radi cntrl mdule. This paper cntains sme

More information

Owner s Manual Installation and Operating Instructions

Owner s Manual Installation and Operating Instructions Meitav-tec Ltd (Cntel grup) Tel: +972 (3) 962 6462 Fax: +972 (3) 962 6620 www.meitavtec.cm - supprt@meitavtec.cm ETN-24-P-1S Owner s Manual Installatin and Operating Instructins Please read this manual

More information

Ethernet Gateway User Manual

Ethernet Gateway User Manual Summer 17 Ethernet Gateway Table f Cntents INTRODUCTION 3 AT A GLANCE 4 ETHERNET GATEWAY SETUP VIA DHCP 5 JACKS, BUTTONS, AND PORTS 6 TROUBLESHOOTING THE ETHERNET GATEWAY 7 LED INDICATOR LIGHTS 7 NO READINGS

More information

Dry Contact Sensor

Dry Contact Sensor www.akcp.cm Dry Cntact Sensr Intrductin The Dry Cntact sensr is a simple cnnectin t burglar alarms, fire alarms r any applicatin that requires mnitring by the unit. Dry cntact sensrs are user definable

More information

SVT Tab and Service Visibility Tool Job Aid

SVT Tab and Service Visibility Tool Job Aid Summary This Jb Aid cvers: SVT Tab Overview Service Visibility Tl (SVT) Area Overview SVT Area: Satellite Mdem Status (Frm Mdem) Clumn SVT Area: Satellite Mdem Status (Frm SMTS) Clumn SVT Area: Prvisining

More information

ACM1281 NFC Reader Module Reference Information

ACM1281 NFC Reader Module Reference Information ACM1281 NFC Reader Mdule Reference Infrmatin ACM1281 NFC Reader Mdule Technical Reference Infrmatin V1.00 Subject t change withut prir ntice inf@acs.cm.hk www.acs.cm.hk Versin Histry Date By Changes Versin

More information

SolarEdge. StorEdge Installation Guide. For North America Version 1.0

SolarEdge. StorEdge Installation Guide. For North America Version 1.0 SlarEdge StrEdge Installatin Guide Fr Nrth America Versin 1.0 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval

More information

Dry Contact Sensor DCS15 User Manual

Dry Contact Sensor DCS15 User Manual Dry Cntact Sensr DCS15 User Manual Help Versin updated till firmware 404i / SP456 Cpyright 2012, AKCess Pr C., Ltd.. Intrductin / What is a Dry Cntact Sensr The Dry Cntact sensr r DCS15 is a simple cnnectin

More information

PhotoVu Digital Picture Frame Service & Repair Guide

PhotoVu Digital Picture Frame Service & Repair Guide PhtVu Digital Picture Frame Service & Repair Guide PhtVu, LLC 2450 Central Ave, #G1 Bulder, CO 80301 USA www.phtvu.cm/supprt Versin: 1.0 Table f Cntents Getting Started... 3 Determine Yur Generatin f PhtVu

More information

SISTEMA ELEVATÓRIO ETV 460A

SISTEMA ELEVATÓRIO ETV 460A Parts included with yur Flat Lift Lift unit ( #1 ) Pwer supply ( #2 ) R.F. Mdule ( #3 ) Rcker switch ( #4 ) Remte Cntrl ( #5 ) Lift unit ( #1 ) Remte Cntrl ( #5 ) Pwer supply ( #2 ) Rcker switch ( #4 )

More information

SolarEdge Feed-in Limitation Application Note

SolarEdge Feed-in Limitation Application Note SolarEdge Feed-in Limitation Application Note Version 1.0 Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a

More information

OPERATING MANUAL SERIES SMTBM BRUSHLESS SINGLE AXIS MODULE

OPERATING MANUAL SERIES SMTBM BRUSHLESS SINGLE AXIS MODULE OPERATING MANUAL SERIES SMTBM BRUSHLESS SINGLE AXIS MODULE Versin 40 This is a general manual describing a series f single axis mdule Serv Amplifiers having utput capability suitable fr driving Brushless

More information

DynaRound Hatch Guard System Installation Instructions

DynaRound Hatch Guard System Installation Instructions DynaRund Hatch Guard System Installatin Instructins Estimated Installatin Time: Man Crew, 0-90 Minutes The DynaRund Hatch Guard System is designed t prtect all rftp hatch entry and exit pints. This nn-penetrating

More information

SolarEdge Feed-in Limitation Application Note

SolarEdge Feed-in Limitation Application Note SolarEdge Feed-in Limitation Application Note Version 1.1 Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a

More information

RS232 Communication Between a Sunny Boy 2500U and a PC. Technical Note

RS232 Communication Between a Sunny Boy 2500U and a PC. Technical Note RS232 Cmmunicatin Between a Sunny By 2500U and a PC Technical Nte Revisin 1.5 July 8, 2003 Kent Sheldn Revisin Histry 1.5 July 8, 2003 Kent Sheldn Cntact update 20830 Red Dg Rad Grass Valley, CA 95945

More information

Remote Control Learn Button Receiver Input Connections

Remote Control Learn Button Receiver Input Connections Remte Cntrl Learn Buttn Receiver Input Cnnectins Remte Cntrl LED Light Wi-fi/Factry Reset Buttn Receiver Output Cnnectin Heartbeat LED Light PRV Cnnectins Pwer Reset Buttn Pl / Treadmill Switch Flat Switch

More information

WS-400 BASE STATION FOR WIRELESS INTERCOM WITH FOUR TX/RX MODULES USER MANUAL

WS-400 BASE STATION FOR WIRELESS INTERCOM WITH FOUR TX/RX MODULES USER MANUAL WS-400 BASE STATION FOR WIRELESS INTERCOM WITH FOUR TX/RX MODULES USER MANUAL Issue February 2011 ASL Intercm BV DESIGNED AND MANUFACTURED BY: ASL INTERCOM BV ZONNEBAAN 42 3542 EG UTRECHT THE NETHERLANDS

More information

Disclaimers. Important Notice. FCC Compliance. Disclaimers

Disclaimers. Important Notice. FCC Compliance. Disclaimers Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval system r transmitted, in any frm r by any means, electrnic,

More information

Altis Flight Manager. PC application for AerobTec devices. AerobTec Altis v3 User Manual 1

Altis Flight Manager. PC application for AerobTec devices. AerobTec Altis v3 User Manual 1 Altis Flight Manager PC applicatin fr AerbTec devices AerbTec Altis v3 User Manual 1 Table f Cntents Intrductin...3 Requirements...3 Installatin...3 Applicatin...3 USB Driver fr Altis v3 interface ALink...4.NET

More information

Application for Drive Technology

Application for Drive Technology Applicatin fr Drive Technlgy MICROMASTER 4 Applicatin Descriptin Warranty, Liability and Supprt 1 Warranty, Liability and Supprt We d nt accept any liability fr the infrmatin cntained in this dcument.

More information

Documentation of the PIC32 Pin Finder

Documentation of the PIC32 Pin Finder App. Versin: 1.1.1.120 Dcument Versin: 1.0 Dcument Create date: 2009-10-16 Dcument Update: 2009-10-19 22:37 Authr: B Gärdmark Cmpany: Spectrn System Develpment AB WEB: www.spectrn.us Cpyright 2009 All

More information

RE926S-SimonXT WiFi IGM

RE926S-SimonXT WiFi IGM RE926S-SimnXT WiFi IGM Features Cnnects panels t lcal WiFi Netwrk Cmpatible with: GE Simn XT GE Simn XTi Enables: Alarm Reprting Interactive Cntrl Functins Ethernet data reliability Z-Wave Cmmunicatr included

More information

Flash Image Rotator Web Part

Flash Image Rotator Web Part Flash Image Rtatr Web Part User Guide Cpyright 2007 Data Springs Inc. All rights reserved. Table f cntents: 1 INTRODUCTION...3 2 INSTALLATION PROCEDURE...4 2.1 After installatin ntes:...5 2.2 Trubleshting...6

More information

Figure 1: View, connection compartment closed

Figure 1: View, connection compartment closed Radi Management Art. N. : 2700AP Operating instructins 1 Safety instructins Electrical equipment may nly be installed and fitted by electrically skilled persns. Serius injuries, fire r prperty damage pssible.

More information

Single Phase Inverter with HD-Wave Technology Installation Guide. For North America Version 1.1

Single Phase Inverter with HD-Wave Technology Installation Guide. For North America Version 1.1 Single Phase Inverter with HD-Wave Technlgy Installatin Guide Fr Nrth America Versin 1.1 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be

More information

Wireless Bridge Module for DXR2.E

Wireless Bridge Module for DXR2.E Technical Specificatin Sheet Dcument N. A6V11470500 July 31, 2018 Wireless Bridge Mdule fr DXR2.E Descriptin A wireless bridge cnnects tw wired netwrks tgether ver Wi-Fi utilizing a Wireless Access Pint.

More information

CB-030S Circuit Board

CB-030S Circuit Board CB-030S Circuit Bard Designed fr use with the high trque PM486FH (up t 7A) Adjustable acceleratin and deceleratin time (0 t 2.5s) Stable speed peratin Switch fr manual r autmatic recvery f the thermal

More information

RZ251W. Remote Sensing & Zoning Installation Guide. Quick Reference. Wireless Range

RZ251W. Remote Sensing & Zoning Installation Guide. Quick Reference. Wireless Range Remte Sensing & Zning Installatin Guide Pr Technlgies P.O. Bx 3377 Springfield, MO 65804 Tll ree : 888-776-47 Web: www.priaq.cm Hurs f Operatin: M- 9AM - 6PM Eastern Table f Cntents Table f Cntents Quick

More information

SolarEdge. StorEdge Installation Guide. For North America Version 1.2

SolarEdge. StorEdge Installation Guide. For North America Version 1.2 SlarEdge StrEdge Installatin Guide Fr Nrth America Versin 1.2 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval

More information

.,Plc..d,~t l~ucjio PA300 DIGITAL BASS PROCESSOR USER'S MANUAL. 2 Why use the DIGITAL BASS PROCESSOR? 2 About the PWM Subsonic Filter

.,Plc..d,~t l~ucjio PA300 DIGITAL BASS PROCESSOR USER'S MANUAL. 2 Why use the DIGITAL BASS PROCESSOR? 2 About the PWM Subsonic Filter .,Plc..d,~t l~ucji PA300 DIGITAL BASS PROCESSOR Cngratulatins n yur purchase f a Planet Audi signal prcessr. It has been designed, engineered and manufactured t bring yu the highest level f perfrmance

More information

LED wdali MC Switch Input Modul Set - User Manual

LED wdali MC Switch Input Modul Set - User Manual LED wli MC Switch Input Mdul Set - User Manual Buttn mdul (Transmitter) 1. Prduct Descriptin Item N.: LC-004-302 Receive mdul (Receiver) The wli MC Switch Input Mdul Set is a cmpact wireless Multi Cntrl

More information

NATF CIP Requirement R1 Guideline

NATF CIP Requirement R1 Guideline Open Distributin NATF CIP 014-2 Requirement R1 Guideline Disclaimer This dcument was created by the Nrth American Transmissin Frum (NATF) t facilitate industry wrk t imprve physical security. NATF reserves

More information

2015 Chevrolet Corvette Corvette Service Manual Body Systems Vehicle Access Repair Instructions Document ID:

2015 Chevrolet Corvette Corvette Service Manual Body Systems Vehicle Access Repair Instructions Document ID: xtltipelement Service Infrmatin 2015 Chevrlet Crvette Crvette Service Manual 7527625 Bdy Systems Vehicle Access Repair Instructins Dcument ID: 3448513 Remte Cntrl Dr Lck and Theft Deterrent Transmitter

More information

Ten-Tec Model RX-366 Subreceiver 565/566 Subreceiver Installation and Operation Manual-74467

Ten-Tec Model RX-366 Subreceiver 565/566 Subreceiver Installation and Operation Manual-74467 Ten-Tec Mdel RX-366 Subreceiver 565/566 Subreceiver Installatin and Operatin Manual-74467 Tls required: Sldering irn r heat gun (fr shrinking heat shrink tubing) Number 1 Phillips screw driver Number 2

More information

Security Exercise 12

Security Exercise 12 Security Exercise 12 Asynchrnus Serial Digital Baseband Transmissin Discussin: In this chapter, yu learned that bits are transmitted ver a cpper wire as a series f vltage pulses (a prcess referred t as

More information

Spectracom GSG ecall Test Suite

Spectracom GSG ecall Test Suite 18-Dec-2017 GSG App Nte Spectracm GSG ecall Test Suite Table f Cntents 1. Intrductin... 1 2. Befre Starting the Test... 2 3. Running the ecall Test Suite... 4 4. Psitin Errr Tests 2.2.2-2.2.4... 10 5.

More information

C&E Mobility Policy (Standard)

C&E Mobility Policy (Standard) C&E Mbility Plicy (Standard) Originated By: DOCUMENT # VERSION: ISSUE DATE: C&E Mbility Prgram Office ATT-CEM-14001 1 5/16/2014 Title: Upladed t VMT: Last Review Date: Next Review Due By: Raycap Equipment

More information

Technical Documentation

Technical Documentation DIN-RAIL MOUNTING ACCORDING TO EN60715. AC MAINS POWER SUPPLY. RS485 SERIAL COMMUNICATION. IR SERIAL COMMUNICATION (2 PORTS). WI-FI COMMUNICATION. PULSE INPUT (OPTIONAL) AND TEMPERATURE SENSOR INPUT (OPTIONAL).

More information

Electrical devices may only be mounted and connected by electrically skilled persons.

Electrical devices may only be mounted and connected by electrically skilled persons. 2-gang Art. N. : HS2 RF 4-gang Art. N. : HS4 RF Operating instructins 1 Safety instructins Electrical devices may nly be munted and cnnected by electrically skilled persns. Serius injuries, fire r prperty

More information

E-Learning, DC drives DCS800 Hardware Options, part 1 Size D1 D4. ABB Group February 2, 2010 Slide 1 DCS800_HARDWARE_OPTIONS_01R0101

E-Learning, DC drives DCS800 Hardware Options, part 1 Size D1 D4. ABB Group February 2, 2010 Slide 1 DCS800_HARDWARE_OPTIONS_01R0101 E-Learning, DC drives DCS800 Hardware Optins, part 1 Size D1 D4 February 2, 2010 Slide 1 Objectives This training mdule cvers: Lcatin fr plug-in ptins Types f plug-in ptins Fiber ptic cnnectin bard DCS800

More information

Connection tariffs

Connection tariffs Cnnectin tariffs 2016-2019 A. TARIFF CONDITIONS FOR GRID USERS DIRECTLY CONNECTED TO THE ELIA GRID AND FOR DISTRIBUTION GRID OPERATORS, EXCEPTED FOR DISTRIBUTION GRID OPERATORS CONNECTED AT TRANSFORMER

More information

Pre-Installation Preparation Job Aid

Pre-Installation Preparation Job Aid Summary This Jb Aid cvers: ViaSat Installatin Standards Equipment Necessary fr ViaSat Service installatin Installatin Tls Safety: IDU Safety: ODU Safety: Persnal Safety: Wrking Arund Electricity Safety:

More information

OPERATOR S MANUAL BOP (M) (D) 100W, 200W, 400W BIPOLAR POWER SUPPLY

OPERATOR S MANUAL BOP (M) (D) 100W, 200W, 400W BIPOLAR POWER SUPPLY OPERATOR S MANUAL BOP (M) (D) 100W, 200W, 400W BIPOLAR POWER SUPPLY 100W: BOP 20-5, BOP 50-2, BOP 100-1 200W: BOP 20-10, BOP 36-6, BOP 50-4, BOP 72-3, BOP 100-2, BOP 200-1 400W: BOP 20-20, BOP 36-12, BOP

More information

-Three Phase Inverter with Synergy Technology Installation MAN

-Three Phase Inverter with Synergy Technology Installation MAN Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval system r transmitted, in any frm r by any means, electrnic,

More information

Desktop Teller Exception User Guide

Desktop Teller Exception User Guide Desktp Teller Exceptin User Guide Jammed Dcuments If a dcument jams during the scanning prcess, the scanner will stp, and a message bx will display a Device Errr Message, as shwn belw: Click OK t allw

More information

Beechcraft Bonanza HID Landing Light Assembly Kit

Beechcraft Bonanza HID Landing Light Assembly Kit Beech Bnanza HID Light Assembly Kit Manual N. HID-B-001 Issue Date: 5-8-05 STC N. SA01834CH Revisin Date: 12-22-07 Beechcraft Bnanza HID Landing Light Assembly Kit INSTALLATION MANUAL N. HID-B-001 Beechcraft

More information

SolarEdge. StorEdge Solution with Backup Installation Guide. For North America Version 1.3

SolarEdge. StorEdge Solution with Backup Installation Guide. For North America Version 1.3 SlarEdge StrEdge Slutin with Backup Installatin Guide Fr Nrth America Versin 1.3 Revisin Histry Revisin Histry Versin 1.3 (Oct. 2017) In Pwer Optimizer Installatin chapter: Added warning abut grunding

More information

Universal input/output controller

Universal input/output controller Embedded autmatin equipment (Shanghai) Limited Rm 305. Twer B.NO.18Talin rad Pudng District, Shanghai Phne: +86-21-51090839/50750355, fax: +86-21-50758598, e-mail: sales@stammkn.cm Universal input/utput

More information

Application Note: Conducted Immunity: Quick Guide

Application Note: Conducted Immunity: Quick Guide icatin Nte: Cnducted Immunity: Quick Guide (Please refer t AZD052 fr the full applicatin nte) 1 Intrductin: Lng cables are at risk f picking up RF, but t test this belw 80MHz require very large antennas

More information

HygroFlex HF4 Humidity Temperature Transmitters. User Guide

HygroFlex HF4 Humidity Temperature Transmitters. User Guide Page 1 f 27 HygrFlex HF4 Humidity Temperature Transmitters User Guide 2009; E-M-HF4-V1_20 Page 2 f 27 Table f cntents 1 Overview... 3 2 Mechanical cnfiguratins and dimensins... 4 2.1 Display and keypad

More information

Xerox 8160/8142 Wide Format Color

Xerox 8160/8142 Wide Format Color PRODUCT RANGE / POSITIONING The Xerx 8142/8160 Slutin Printer is a thermal inkjet printing system intended fr use in a prductin envirnment prducing graphical cntent, including Psters, POP, signage, etc.

More information

FieldServer EZ Gateway Modbus to BACnet Start-up Guide FS-EZX-MOD-BAC

FieldServer EZ Gateway Modbus to BACnet Start-up Guide FS-EZX-MOD-BAC FieldServer EZ Gateway Mdbus t BACnet Start-up Guide FS-EZX-MOD-BAC APPLICABILITY & EFFECTIVITY Effective fr all systems manufactured after July 2018. Dcument Revisin: 9.B T18048 Technical Supprt EZ Gateway

More information

HygroFlex HF5 Humidity Temperature Transmitters. User Guide

HygroFlex HF5 Humidity Temperature Transmitters. User Guide Page 1 f 31 HygrFlex HF5 Humidity Temperature Transmitters User Guide Page 2 f 31 Table f cntents 1 Overview...3 2 Mechanical cnfiguratins and dimensins...4 2.1 Display and keypad ptin...5 3 General descriptin...5

More information

SolarEdge System Installation Guide

SolarEdge System Installation Guide SlarEdge System Installatin Guide Fr Nrth America Versin 4.2 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval

More information

XDS Pro-4 Network Data Sheet

XDS Pro-4 Network Data Sheet XDS Pr-4 Netwrk Data Sheet In the XDS Quickstart Guide that fllws this page, references are made t the netwrk cnfiguratin data sheet. Please use this dcument fr that purpse. C-Band Satellite: SES Wrld

More information

Models 7008, 7034, 7035, 7035R & 7041 Planar Blind-Mate Connectors, dc to 40.0 GHz

Models 7008, 7034, 7035, 7035R & 7041 Planar Blind-Mate Connectors, dc to 40.0 GHz Mdels 7008, 7034, 7035, 7035R & 7041 Planar Blind-Mate Cnnectrs, dc t 40.0 GHz Threadless Cnnectr System / S pace Saving / L ng Life Features Threadless Cnnectr Mating - This blind-mate cnnectr series

More information

These specifications describe requirements for a power distribution unit (PDU) distributing power to sensitive loads.

These specifications describe requirements for a power distribution unit (PDU) distributing power to sensitive loads. PDI PwerPak 2 Pwer Distributin Unit Guide Specificatins (Revisin 002, 6/1/2017) 1 General 1.1 Summary These specificatins describe requirements fr a pwer distributin unit (PDU) distributing pwer t sensitive

More information

1.12 Equipment Manager

1.12 Equipment Manager Mdule 1 Categry 1 1.12 Equipment Manager Functin f the windw The windw is the central data file fr the Kntrl Pr and cllects the main data fr fees f an bject that t be used in this prject. The Equipment

More information

AIR CONDITIONER REMOTE CONTROLLER ILLUSTRATION CS406-R51E

AIR CONDITIONER REMOTE CONTROLLER ILLUSTRATION CS406-R51E AIR CONDITER REMOTE CONTROLLER ILLUSTRAT CS406-R5E 00550905 0009 Thank yu very much fr purchasing ur air cnditiner. Please read this wner's manual carefully befre using yur air cnditiner. CONTENTS Handling

More information

VIP-200. Point to Point Extension Configuration Quick Start Guide. Video over IP Extender and Matrix System

VIP-200. Point to Point Extension Configuration Quick Start Guide. Video over IP Extender and Matrix System VIP-200 Vide ver IP Extender and Matrix System Pint t Pint Extensin Cnfiguratin Quick Start Guide PureLink TM 535 East Crescent Avenue Ramsey, NJ 07446 USA Cntents What is in the bx... 3 Transmitter kit

More information

For over 25 years Mtroniks have been at the forefront of electronic speed control design and manufacture for the hobby industry.

For over 25 years Mtroniks have been at the forefront of electronic speed control design and manufacture for the hobby industry. DC MOTOR SPEED CONTROLLER MODEL: DCI120-12 True Trque TM Thank yu fr chsing Mtrniks t cntrl yur mdel Overview Dimensins: 133x115x57mm Weight: 700g Fr ver 25 years Mtrniks have been at the frefrnt f electrnic

More information

Creating Gift Card Batches

Creating Gift Card Batches Every active custmer gift card issued is a part f a batch f gift cards. Prir t activating any individual gift card, yu must define a batch f gift cards and any accmpanying rules that apply t each batch.

More information

Application Note AN-2097 Evaluation Kit for the S7500 CW Tunable Laser

Application Note AN-2097 Evaluation Kit for the S7500 CW Tunable Laser Applicatin Nte AN-2097 Evaluatin Kit fr the S7500 CW Tunable Laser 1 Intrductin The evaluatin kit is intended t facilitate testing f Finisar s S7500 widely tunable laser, S7610 Integrable Tunable Laser

More information

CONTENTS. Product Type Output No of Output Input Approvals Page! and Series Power Outputs Voltage Voltage Number. Open Frame.

CONTENTS. Product Type Output No of Output Input Approvals Page! and Series Power Outputs Voltage Voltage Number. Open Frame. NTENTS Prduct Type Output N f Output Input Apprvals Page! and Series Pwer Outputs Vltage Vltage Number Open Frame RA 15t29W 1 5, 15 r 24V 100, 120, 220, 240V a.c. CE 211 RB 30 t 58W 1 5, 12 r 24V 100,

More information

KELOX room thermostats - KM690D Digital-Standard/ KM690U Digital-Control

KELOX room thermostats - KM690D Digital-Standard/ KM690U Digital-Control KELOX rm thermstats - KM690D Digital-Standard/ KM690U Digital-Cntrl The KELOX rm thermstats are high-quality rm temperature cntrllers fr recrding and cntrlling the required rm temperature fr a maximum

More information

A_LT-2W & B_LT-2W Series 2W, FIXED INPUT, ISOLATED & UNREGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTER

A_LT-2W & B_LT-2W Series 2W, FIXED INPUT, ISOLATED & UNREGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTER A_LT-2W & B_LT-2W Series 2W, FIXED INPUT, ISOLATED & UNULATED DUAL/SINGLE OUTPUT - CONVERTER FEATURES Efficiency up t 85% Lw Temperature rise 1KV Islatin SMD Package Operating Temperature Range: - C ~

More information

ELEC 7250 VLSI TESTING. Term Paper. Analog Test Bus Standard

ELEC 7250 VLSI TESTING. Term Paper. Analog Test Bus Standard ELEC 7250 VLSI TESTING Term Paper On Analg Test Bus Standard Muthubalaji Ramkumar 1 Analg Test Bus Standard Muthubalaji Ramkumar Dept. f Electrical and Cmputer Engineering Auburn University Abstract This

More information

TUTORIAL I ECE 555 CADENCE SCHEMATIC SIMULATION USING SPECTRE

TUTORIAL I ECE 555 CADENCE SCHEMATIC SIMULATION USING SPECTRE TUTORIAL I ECE 555 CADENCE SCHEMATIC SIMULATION USING SPECTRE Cadence Virtus Schematic editing prvides a design envirnment cmprising tls t create schematics, symbls and run simulatins. This tutrial will

More information

User Guide. ACC Mobile 3 Preview App for ios

User Guide. ACC Mobile 3 Preview App for ios User Guide ACC Mbile 3 Preview App fr ios 2017, Avigiln Crpratin. All rights reserved. AVIGILON, the AVIGILON lg, AVIGILON CONTROL CENTER, ACC, and TRUSTED SECURITY SOLUTIONS are trademarks f Avigiln Crpratin.

More information

Omni-Bus Interface Translator Rev 2. Reference Manual

Omni-Bus Interface Translator Rev 2. Reference Manual Omni-Bus Interface Translatr Rev 2 Reference Manual Table f Cntents 1. Overview... 3 1.1. LEVITON Omni Link Interface... 3 1.2. Bus Gateway... 4 2. TCPIP Netwrk Setup... 5 3. USB Gateway Setup... 6 4.

More information

Wonder Tree Video Slot Introduction. How to Bet. Gamble Feature

Wonder Tree Video Slot Introduction. How to Bet. Gamble Feature Wnder Tree Vide Slt Intrductin Wnder Tree vide slt is a 5-reel, 20-line game. The slt cnsists f 11 cards - 1 f which is Wild, and 1 is Scatter. All winning cmbinatins are paid left t right, except fr the

More information

PS 430 FOUR CHANNEL REMOTE SPEAKER STATION

PS 430 FOUR CHANNEL REMOTE SPEAKER STATION PS 430 FOUR CHANNEL REMOTE SPEAKER STATION USER MANUAL August 2016 This prduct is designed and manufactured by: ASL Intercm BV Znnebaan 42 3542 EG Utrecht The Netherlands Phne: +31 (0)30 2411901 Fax: +31

More information

Maxon Motor & Motor Controller Manual

Maxon Motor & Motor Controller Manual Maxn Mtr & Mtr Cntrller Manual Nte: This manual is nly fr use fr the Maxn mtr and cntrller utlined belw. This infrmatin is based upn the tutrial vides fund nline and thrugh testing. NOTE: Maximum Permitted

More information

USER MANUAL HIGH INTERCEPT LOW NOISE AMPLIFIER (HILNA TM ) V1

USER MANUAL HIGH INTERCEPT LOW NOISE AMPLIFIER (HILNA TM ) V1 USER MANUAL HIGH INTERCEPT LOW NOISE AMPLIFIER (HILNA TM ) V1 PART NUMBERS: HILNA-V1 HILNA-V1-M/F RF, Wireless, and Embedded Systems Engineering NuWaves Engineering 132 Edisn Drive Middletwn, Ohi 45044

More information

HygroFlex HF5 Humidity Temperature Transmitters. User Guide

HygroFlex HF5 Humidity Temperature Transmitters. User Guide Page 1 f 36 HygrFlex HF5 Humidity Temperature Transmitters User Guide Page 2 f 36 Table f cntents 1 Overview... 3 2 Mechanical cnfiguratins and dimensins... 4 2.1 Supply vltage up t 40 VDC / 28 VAC...

More information