SolarEdge. StorEdge Installation Guide. For Smart Energy Management using the StorEdge Interface. For Europe, APAC & South Africa. Version 1.

Transcription

1 SlarEdge StrEdge Installatin Guide Fr Smart Energy Management using the StrEdge Interface Fr Eurpe, APAC & Suth Africa Versin 1.3

2 Disclaimers Disclaimers Imprtant Ntice Cpyright SlarEdge Inc. All rights reserved. N part f this dcument may be reprduced, stred in a retrieval system r transmitted, in any frm r by any means, electrnic, mechanical, phtgraphic, magnetic r therwise, withut the prir written permissin f SlarEdge Inc. The material furnished in this dcument is believed t be accurate and reliable. Hwever, SlarEdge assumes n respnsibility fr the use f this material. SlarEdge reserves the right t make changes t the material at any time and withut ntice. Yu may refer t the SlarEdge web site ( fr the mst updated versin. All cmpany and brand prducts and service names are trademarks r registered trademarks f their respective hlders. Patent marking ntice: see The general terms and cnditins f delivery f SlarEdge shall apply. The cntent f these dcuments is cntinually reviewed and amended, where necessary. Hwever, discrepancies cannt be excluded. N guarantee is made fr the cmpleteness f these dcuments. The images cntained in this dcument are fr illustrative purpses nly and may vary depending n prduct mdels. Emissin Cmpliance This equipment has been tested and fund t cmply with the limits applied by the lcal regulatins. These limits are designed t prvide reasnable prtectin against harmful interference in a residential installatin. This equipment generates, uses and can radiate radi frequency energy and, if nt installed and used in accrdance with the instructins, may cause harmful interference t radi cmmunicatins. Hwever, there is n guarantee that interference will nt ccur in a particular installatin. If this equipment des cause harmful interference t radi r televisin receptin, which can be determined by turning the equipment ff and n, yu are encuraged t try t crrect the interference by ne r mre f the fllwing measures: Rerient r relcate the receiving antenna. Increase the separatin between the equipment and the receiver. Cnnect the equipment int an utlet n a circuit different frm that t which the receiver is cnnected. Cnsult the dealer r an experienced radi/tv technician fr help. Changes r mdificatins nt expressly apprved by the party respnsible fr cmpliance may vid the user s authrity t perate the equipment. -StrEdge Interface Installatin Guide MAN

3 Cntents Cntents Disclaimers 1 Imprtant Ntice 1 Emissin Cmpliance 1 Cntents 2 HANDLING AND SAFETY INSTRUCTIONS 4 Safety Infrmatin 4 IMPORTANT SAFETY INSTRUCTIONS 4 Chapter 1: Overview 6 The StrEdge Slutin Cmpnents 6 Abut this Guide 7 Installatin Wrkflw 8 Installatin Equipment List 9 Inverter Transprt and Strage 9 Chapter 1: Meter Installatin 10 Chapter 2: StrEdge Interface Installatin 12 Unpacking and Identifying the Prduct 12 Munting the StrEdge Interface 12 Cnnecting the StrEdge Interface 13 Cnnecting the StrEdge Interface t the Inverter 13 Cnnecting the StrEdge Interface t AC 15 Cnnecting the StrEdge Interface t the Battery Pack 17 DIP Switch Setup 18 Chapter 3: System Cnfiguratin 22 Upgrading the Inverter Firmware Versin 22 Cnfiguring the RS485 Bus fr Battery and Meter Cnnectin 23 Cnfiguring Maximum Self-cnsumptin 25 Maximize Self-cnsumptin (MSC) 25 Prfile Prgramming (fr time-f-use arbitrage) 26 Starting-up the System 26 Appendix A: Trubleshting 27 Cmmunicatin Trubleshting 27 Device type, number and prtcl are displayed incrrectly 27 Trubleshting Ethernet Cmmunicatin 27 Meter Trubleshting 28 <OK> is nt displayed 28 An errr message is displayed 28 Pwer [Wh] Imprt value is nt advancing 28 Battery Trubleshting 29 StrEdge Interface LEDs 30 Appendix B: Additinal Battery Cnnectins 31 Cnnectin with One Battery 31 Tesla Pwerwall1 31 LG Chem RESU7H/RESU10H 35 2 StrEdge Interface Installatin Guide MAN

4 Cntents Cnnectins with Tw Batteries 37 Tesla Pwerwall1 37 DIP-Switch Setup - Pwerwall1 Batteries 40 Appendix C: StrEdge Interface Technical Specificatins 43 -StrEdge Interface Installatin Guide MAN

5 HANDLING AND SAFETY INSTRUCTIONS HANDLING AND SAFETY INSTRUCTIONS During installatin, testing and inspectin, adherence t all the handling and safety instructins is mandatry. Failure t d s may result in injury r lss f life and damage t the equipment. Safety Infrmatin WARNING! Dentes a hazard. It calls attentin t a prcedure that, if nt crrectly perfrmed r adhered t, culd result in injury r lss f life. D nt prceed beynd a warning nte until the indicated cnditins are fully understd and met. CAUTION! Dentes a hazard. It calls attentin t a prcedure that, if nt crrectly perfrmed r adhered t, culd result in damage r destructin f the prduct. D nt prceed beynd a cautin sign until the indicated cnditins are fully understd and met. NOTE Dentes additinal infrmatin abut the current subject. IMPORTANT SAFETY FEATURE Dentes infrmatin abut safety issues. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING! The inverter cver must be pened nly after shutting ff the inverter ON/OFF switch lcated at the bttm f the inverter. This disables the DC vltage inside the inverter. Wait five minutes befre pening the cver. Otherwise, there is a risk f electric shck frm energy stred in the capacitrs. WARNING! D nt remve the StrEdge Interface cver befre five minutes have elapsed after discnnecting all surces f pwer, and shutting OFF the inverter and the StrEdge Interface. WARNING! Befre perating the system, ensure that the pwer cable and wall utlet have been grunded prperly. WARNING! When handling the battery, adhere t all manufacturer safety instructins. 4 StrEdge Interface Installatin Guide MAN

6 HANDLING AND SAFETY INSTRUCTIONS WARNING! The battery shuld be pwered OFF befre and during wiring. Turn OFF: The auxiliary pwer supply switch The circuit breaker switch CAUTION! This unit must be perated under the specified perating cnditins as described in the technical specificatins supplied with the unit. NOTE The battery used must be NRTL certified. NOTE Fr battery decmmissining and dispsal, fllw the manufacturer requirements and instructins. NOTE The StrEdge Interface is IP65 rated. Unused cnnectrs and glands shuld be sealed with the prvided seals. NOTE The symbl appears at grunding pints n the SlarEdge equipment. This symbl may als be used in this manual. -StrEdge Interface Installatin Guide MAN

7 Chapter 1: Overview Chapter 1: Overview SlarEdge s StrEdge slutin fr Smart Energy Management uses the StrEdge Interface t cnnect the battery t the inverter. Pwer is stred in the battery and can be used fr varius applicatins such as maximized selfcnsumptin and time f use prfile prgramming. Fr backup pwer, an inverter specifically designed fr backup applicatins is required; this inverter is nt in the scpe f this dcument. The StrEdge Slutin Cmpnents The SlarEdge Inverter The SlarEdge Meter - The meter is used by the inverter fr exprt/ cnsumptin readings, and fr Smart Energy Management applicatins, such as: exprt limitatin and maximizing self-cnsumptin. The StrEdge Interface - The StrEdge Interface cnnects the battery t the inverter thrugh fuses, and supplies cntrl and mnitring signals t the battery fr peratin. One r tw batteries - DC cupled batteries designed t wrk with the SlarEdge system. CAUTION! Figure 1: StrEdge system cmpnents D nt cnnect this StrEdge Interface unit t SlarEdge HD-Wave inverters when using LG Chem batteries. Cnnecting these prducts may damage the equipment and vid the warranty. NOTE Additinal SlarEdge inverters (withut batteries) can be cnnected with RS485. The inverters will participate in exprt limitatin and Smart Energy Management. Cnnecting multiple inverters with RS485 master-slave cnnectin may require an RS485 Expansin Kit (available frm SlarEdge). PV mdules cnnected t pwer ptimizers are nt mandatry fr charge/discharge prfile prgramming and fr backup pwer. 6 StrEdge Interface Installatin Guide MAN

8 Abut this Guide This dcument describes basic system cnnectin and cnfiguratin - PV system (pwer ptimizer strings), ne inverter, ne battery, backed-up lads panel and ne meter. Fr additinal cnfiguratin ptins refer t the StrEdge Slutin Applicatins - Cnnectin and Cnfiguratin Guide, available at cnnectin_and_cnfiguratin_guide.pdf. Chapter 1: Overview -StrEdge Interface Installatin Guide MAN

9 Installatin Wrkflw Installatin Wrkflw When installing the StrEdge system, fllw this wrkflw t ensure all the cmpnents are cnnected and functining crrectly. Plan the StrEdge system layut: The battery and StrEdge Interface will cnnect t the DC side f the inverter. Since the inverter DC cnnectins are n its left side, it is recmmended t psitin the battery and interface t the left f the inverter t simplify wiring. T simplify cable management, a minimum distance f 1.5m between battery and interface is recmmended. Figure 2: System Layut Step 1 - PV system installatin - mdules, pwer ptimizers and inverter(s). Refer t the fllwing chapters f the SlarEdge Installatin Guide supplied with the inverter and available at Installing the Pwer Optimizers (if applicable) Installing the Inverter Cnnecting the AC and the Strings t the Inverter Activating the inverter- as described in the Cmmissining chapter f the SlarEdge Installatin Guide, using the activatin card supplied with the inverter. Upgrading the inverter firmware versin, using the upgrade card supplied with the StrEdge Interface. Pairing the system - as described in the Cmmissining chapter f the SlarEdge Installatin Guide Setting Up Cmmunicatin Step 2 - Electricity Meter installatin (required fr Smart Energy Management). Refer t Meter Installatin n page 10. Step 3 - StrEdge Interface installatin and cnnectin as described in StrEdge Interface Installatin n page 12. Step 4 - Cnnect the battery t the StrEdge Interface and munt the battery. Refer t the installatin infrmatin in the manufacturer dcumentatin, and t Cnnecting the StrEdge Interface t the Battery Pack n page 17. Step 5 - Cnfiguring the cmmunicatin between the inverter and the ther devices (meter, battery, etc.). Refer t Cnfiguring the RS485 Bus fr Battery and Meter Cnnectin n page 23. Step 6 - System Cnfiguratin - Cnfiguring the RS485 bus and StrEdge applicatins. Refer t System Cnfiguratin n page StrEdge Interface Installatin Guide MAN

10 Installatin Equipment List Standard tls can be used during the installatin f the SlarEdge system. The fllwing is a recmmendatin f the equipment needed fr installatin: Standard flat-head screwdrivers set Nn-cntact vltage detectr Suitable hardware fr attaching the inverter munting bracket t the surface t which it will be cnnected Wire cutters Wire strippers Vltmeter Fr installing the cmmunicatin ptins, yu may als need the fllwing: Fr Ethernet: Fr RS485: CAT5/6 twisted pair Ethernet cable with RJ45 cnnectr. If using a CAT5/6 cable spl: RJ45 plug and RJ45 crimper Fur- r six-wire shielded twisted pair cable. Watchmaker precisin screwdriver set Inverter Transprt and Strage Chapter 1: Overview Transprt the inverter in its riginal packaging, facing up and withut expsing it t unnecessary shcks. If the riginal package is n lnger available, use a similar bx that can withstand the weight f the inverter (refer t the inverter weight in the specificatin datasheet prvided with the unit), has a handle system and can be clsed fully. -StrEdge Interface Installatin Guide MAN

11 Chapter 1: Meter Installatin Chapter 1: Meter Installatin The StrEdge slutin requires cnnecting a meter fr Smart Energy Management applicatins, such as exprt limitatin and maximizing self-cnsumptin. The meter type (single r three phase) and number f current transfrmers (CTs) shuld be selected per the grid cnnectin and energy management applicatin rather than accrding t the inverter mdel. The CTs are supplied with 2m twisted pair wires fr cnnecting the CTs. T install the SlarEdge meter, refer t the installatin guide supplied with it:. The meter is cnnected t the inverter using RS485. RS485 wiring specificatins: Cable type: Min. 3-wire shielded twisted pair (a shielded Ethernet cable (Cat5/5E STP) may be used) Wire crss-sectin area: mm²/ AWG (a CAT5 cable may be used) NOTE The inverter RS485 bus shuld be cnnected t the battery (via the StrEdge interface) and meter. Cnnecting multiple inverters (r an external lgger) with RS485 master-slave cnnectin may require an RS485 Expansin Kit (available frm SlarEdge; Refer t kit_installatin_guide.pdf). T cnnect the meter t the inverter: 1. Remve the seal frm ne f the penings in cmmunicatin gland at the bttm f the inverter and insert the RS485 wires frm the meter thrugh the pening. Figure 3: Cmmunicatin glands (Left - single phase inverter; Right - HD-Wave inverter) 2. Pull ut the 9-pin RS485 cnnectr lcated n the cmmunicatin bard. Figure 4: Inverter RS485 cnnectr (Left - single phase inverter; Right - HD-Wave inverter) 10 StrEdge Interface Installatin Guide MAN

12 Chapter 1: Meter Installatin 3. Cnnect the wires as illustrated belw: Figure 5: Meter RS485 cnnectins (Left - single phase inverter; Right - HD-Wave inverter) 4. Terminate the last device in the RS485 chain (see als DIP Switch Setup n page 18): If the inverter is at the end f the RS485 bus, switch a terminatin DIP-switch inside the inverter t ON (tp psitin). The switch is lcated n the cmmunicatin bard as fllws: Figure 6: RS485 terminatin switch (Left - single phase inverter; Right - HD-Wave inverter) If the meter is at the end f the RS485 chain, it shuld be terminated using its DIP switches (see als DIP Switch Setup n page 18). If required, cntact SlarEdge Supprt fr an external 120 Ohm terminatin plug. -StrEdge Interface Installatin Guide MAN

13 Chapter 2: StrEdge Interface Installatin Chapter 2: StrEdge Interface Installatin Unpacking and Identifying the Prduct An identificatin label with prduct specificatins is attached t each device. Check the equipment fr damage befre starting installatin: There are n lse parts. All parts are either munted r lcated in the accessry kit. If any damage is fund, dcument the damage, and cntact SlarEdge. Munting the StrEdge Interface 1. Determine the StrEdge Interface munting lcatin, n a wall r ple, as fllws: Maximum distance frm the battery: 5m (15 ft) Maximum distance frm the inverter: 100m (328 ft) Maintain a minimum 20 cm (8 ) clearance between the StrEdge Interface and ther bjects. Figure 7: StrEdge Interface clearance 2. Install the bracket with the semi-circles facing dwn, as shwn belw. Verify that the bracket is firmly attached t the munting surface. Figure 8: Munting bracket 3. Install the interface: Attach the StrEdge interface back brackets t the munted bracket using the fur supplied screws. Tighten the screws with a trque f 9 N*m / 6.6 lb*ft. Figure 9: The StrEdge Interface 4. Lsen the 4 Allen screws f the StrEdge Interface and remve the cver. 12 StrEdge Interface Installatin Guide MAN

14 Cnnecting the StrEdge Interface Chapter 2: StrEdge Interface Installatin Figure 10: StrEdge Interface cnnectrs Cnnecting the StrEdge Interface t the Inverter T cnnect t the inverter DC: 1. Prepare ne pair f DC cables with MC4 cnnectrs at bth ends - male at ne end and female at the ther end. 2. Cnnect ne end f the cables t the inverter, and cnnect the ther end t the DC+ and DC- input cnnectrs marked INV OUT. NOTE If all the inverter DC inputs are cnnected t PV strings, use a branch cable (available frm SlarEdge) t cnnect the StrEdge Interface t the inverter DC input. T cnnect RS485 cmmunicatin between the inverter and StrEdge Interface: RS485 wiring specificatins: Cable type: Min. 3-wire shielded twisted pair (a shielded Ethernet cable (Cat5/5e STP) may be used) Wire crss-sectin area: mm²/ AWG (a CAT5 cable may be used) 1. Cnnect ne end t the RS485 terminal blck marked "RS485 t Inv." in the StrEdge Interface: a. Open gland #2. b. Remve the seal frm ne f the penings and insert the wire thrugh the pening. c. Cnnect the wire ends in the A, B and G pins (use a twisted pair fr A and B): Use a flat blade screwdriver t press the prtrusin at the tp f the terminal blck and pen the cnnectin hle; insert the wire and release t spring back and clamp the wire. Yu can use any clr wire fr each f the A, B and G cnnectins, as lng as the same clr wire is used fr bth A pins (inverter and StrEdge Interface, the same clr fr bth B pins and the same clr fr bth G pins. -StrEdge Interface Installatin Guide MAN

15 Cnnecting the StrEdge Interface t the Inverter Figure 11: RS485 cnnectr in the StrEdge Interface 2. Cnnect the ther end f the cmmunicatin cable t the inverter cmmunicatin bard: NOTE The wires frm the meter and frm the StrEdge Interface are inserted int the same pins in the inverter RS485 terminal blck. Make sure that the meter wires are nt discnnected when inserting the Interface wires. a. Open the inverter cver as described in its manual. b. Remve the seal frm ne f the penings in the cmmunicatin gland and insert the wire thrugh the pening. Figure 12: Inverter Cmmunicatin glands (Left - single phase inverter; Right - HD-Wave inverter) c. Pull ut the 9-pin RS485 terminal blck cnnectr, as shwn belw: Figure 13: Inverter RS485 terminal blck (Left - single phase inverter; Right - HD-Wave inverter) d. Lsen the screws f pins A(+), B(-), and G n the left f the RS485 terminal blck. e. Insert the wire ends int the G, A and B pins. 14 StrEdge Interface Installatin Guide MAN

16 Chapter 2: StrEdge Interface Installatin 3. Check that the wires are fully inserted and cannt be pulled ut easily. Figure 14: Cnnectins t the inverter and meter (Up - Single phase inverter; Dwn - HD-Wave inverter) Cnnecting the StrEdge Interface t AC NOTE The AC is used fr auxiliary pwer nly and des nt carry high pwer. Use a three-wire cable with a crss sectin f 1-2mm 2. T cnnect t AC: 1. Turn OFF the AC pwer surce t be cnnected t the interface. 2. Remve the interface AC sealing gland. -StrEdge Interface Installatin Guide MAN

17 Cnnecting the StrEdge Interface t AC 3. Strip ff 5/16" (8mm) f the AC cable insulatin and expse tw line wires and ne grunding wire. 4. Insert the wire ends int the AC terminals (L, N), and the grunding terminal accrding t the labels. Fasten the screws with a trque f 0.67 N*m/ 0.5 lb*ft. Figure 15: AC and grunding cnnectins 16 StrEdge Interface Installatin Guide MAN

18 Cnnecting the StrEdge Interface t the Battery Pack Befre installing the battery pack accrding t the instructins prvided by the battery manufacturer, cnnect the battery t the StrEdge Interface as described in this sectin. Fllw these guidelines: Fr easy access t battery cnnectrs, it is recmmended t cnnect the cables t the battery and t set all the battery DIP switches t their crrect psitins while the battery is still n the grund, befre munting the battery accrding t the manufacturer instructins). The fllwing prcedure is recmmended: a. Cnnect all the wires t the battery cnnectin panel b. Munt the battery c. Cnnect t the StrEdge Interface. Measure the necessary length between the StrEdge Interface and the battery fr all cables. Tie and wrap the cables t avid pulling them ut during munting. Chapter 2: StrEdge Interface Installatin Be sure t adhere t all safety cautins and infrmatin in the battery dcumentatin. The fllwing table, Figure 19 detail cable types and cnnectins f the StrEdge Interface ne with 2 DIP switches t ne battery (LG-chem RESU7H/RESU10H). Fr additinal battery types and cnnectin ptins, refer t Additinal Battery Cnnectins n page 31 and stredge_wiring_and_nsite_checklist.pdf r _interface_wiring_quick_guide_and_n_site_checklist_fr_lg_batteries.pdf. w CAUTION! D nt cnnect this StrEdge Interface unit t SlarEdge HD-Wave inverters when using LG Chem batteries. Cnnecting these prducts may damage the equipment and vid the warranty. WARNING! The battery shuld be pwered OFF befre and during wiring. Turn OFF: The auxiliary pwer supply switch The circuit breaker switch -StrEdge Interface Installatin Guide MAN

19 DIP Switch Setup T cnnect the battery pack and the StrEdge Interface: 1. Prepare cables and cnnect as described in the fllwing table; Pay attentin t the wire clrs: Recmmended cable type (minmax crss sectin) DC One pair f PV DC cables with a crss sectin f 6 (4-6)mm 2, 600V insulated, with MC4 cnnectrs at ne end. Cntrl and mnitring 5-wire shielded twisted pair cable with a crss sectin f 0.2 ( ) mm 2. A CAT5 600V insulated cable can als be used. StrEdge Interface cnnectin LG Chem RESU7H/RESU10H battery cnnectin (Figure 19) Cnnectin methd in StrEdge Interface BAT DC + DC+ MC4 cnnectin BAT DC - DC- MC4 cnnectin 5-pin cmmunicatin terminal blck: En (Enable) 6-pin cnnectr ENABLE_H V+ Nt cnnected B (RS485) 1 RS485_H + 2 A (RS485) 1 RS485_L - 2 G (RS485) EN_G 2. Cnnect the battery t grund using the battery grunding terminal. 3. Set the DIP switches as described in DIP Switch Setup n page 18. Press the prtrusin at the tp f the terminal blck t pen the cnnectin hle, insert the wire and release t spring back and clamp the wire. Refer t Figure 19 and Figure Clse the StrEdge Interface cver: Attach the cver and secure it by tightening the fur screws with a trque f 1.2 N*m / 0.9 ft.*lb. DIP Switch Setup Verify that the DIP switches n the system cmpnents are set as described in this sectin, accrding t the system hardware cnfiguratin. This sectin prvides infrmatin abutlg Chem RESU10 batteries. Fr ther types refer t Additinal Battery Cnnectins n page 31 r wiring_and_nsite_checklist.pdf. Terminatin and bias guidelines: The last battery in the RS485 chain shuld have terminatin and bias. The last meter in the RS485 chain shuld be terminated with 120 Ohm (either internal r external). Inverter cmmunicatin bard shuld nt have terminatin if meter is installed, therwise ON. 1Must be twisted pair 2Must be twisted pair 18 StrEdge Interface Installatin Guide MAN

20 Verify that the DIP switches f all the devices are set as described in the fllwing table, accrding t the cmpnents used in the system and their lcatin: System Cmpnent Batteries LG Chem RESU10 N/A Cmmunicatin and Terminatin Switches Address Switches Tesla Pwerwall1 Refer t DIP-Switch Setup - Pwerwall1 Batteries n page 40 StrEdge Interface StrEdge Interface main bard Meters SlarEdge Meter (Figure 18) Inverter Single phase inverters - inverter cmmunicatin bard (Figure 17) HD-Wave inverter cmmunicatin bard (Figure 17) Cmmunicatin DIP switches (if applicable,figure 16 ): Up If the meter is nt the last in the chain - N terminatin Single meter r the meter is the last in the RS485 chain Ohm terminatin 1 n the last meter cnnected n the chain RS485-1 cnnectin - use SW7 DIP switch 1 (leftmst)w If a meter is installed: SW7 Dwn - N terminatin If a meter is nt installed: SW7 Up - terminatin ON.w RS485-1 cnnectin - use SW2 DIP switch 1 (leftmst) N meter installed: Up - terminated Meter is installed: Dwn - Nt terminated Chapter 2: StrEdge Interface Installatin N/A Meter 1 address: Switch 1: Up Other: Dwn Meter 2 address: N/A N/A Switch 2: Up Other: Dwn 1Fr installing an external 120 Ohm terminatin plug, cntact SlarEdge Supprt. -StrEdge Interface Installatin Guide MAN

21 DIP Switch Setup Figure 16: StrEdge Interface Cmmunicatin DIP switches Figure 17: RS485 terminatin switch n the HD-Wave inverter cmmunicatin bard (Left - Single phase inverter; Right - HD-Wave inverter) Figure 18: SlarEdge Meter DIP Switches 20 StrEdge Interface Installatin Guide MAN

22 DIP Switch Setup Figure 19: StrEdge Interface cnnectins with LG Chem RESU10 battery -StrEdge Interface Installatin Guide MAN

23 Chapter 3: System Cnfiguratin Chapter 3: System Cnfiguratin This chapter describes hw t cnfigure yur StrEdge system by setting up the cmmunicatin between the system cmpnents and setting up the required applicatin. T use the StrEdge applicatins, the inverter cmmunicatin bard firmware (CPU) versin must be 3.xxxx and later. The latest firmware versin is available fr dwnlad at Upgrading the Inverter Firmware Versin Upgrade the inverter firmware using a MicrSD card with the latest firmware versin dwnladed frm the abve link. T upgrade the inverter firmware: 1. Make sure that: The inverter has been activated using the activatin card supplied with the inverter The inverter ON/OFF switch is OFF The AC vltage t the inverter is OFF If applicable - the StrEdge Interface ON/OFF switch is OFF. 2. Remve the inverter cver. 3. Insert the card int the cmmunicatin bard slt marked CARD. SlarEdge 1Ph/3Ph inverters SlarEdge 1Ph inverter (HD-Wave) Figure 20: Inserting the upgrade card 4. Turn ON the battery AUX switch and circuit breaker. Wait 1 minute befre prceeding. 5. Turn ON: AC t the StrEdge Interface AC t the inverter WARNING! ELECTRICAL SHOCK HAZARD. D nt tuch uninsulated wires when the cver is remved. 6. The upgrade starts autmatically. Wait fr the message Dne t be displayed n the LCD. 7. Remve the card frm the inverter. 22 StrEdge Interface Installatin Guide MAN

24 Chapter 3: System Cnfiguratin Cnfiguring the RS485 Bus fr Battery and Meter Cnnectin This sectin describes hw t set up the RS485 cmmunicatin between the inverter, meter, StrEdge Interface, and ne battery. Fr infrmatin n cnfiguring tw batteries, refer t the StrEdge Applicatins Cnnectin and Cnfiguratin Guide available at. T cnfigure the RS485 bus: 1. Select Cmmunicatin RS485-1 Cnf Device Type Multi Devices. A list f devices is displayed. D e v i c e T y p e < M L T > M e t e r 1 < > M e t e r 2 < > M e t e r 3 < > B a t t e r y 1 < > B a t t e r y 2 < > 2. Select Meter 2. The meter cnfiguratin screen is displayed (SlarEdge meters are pre-cnfigured t Device ID 2): 3. Cnfigure the meter: D e v i c e T y p e < M T R > P r t c l < W N > D e v i c e I D < 2 > C T R a t i n g < 0 > M e t e r F u n c. < N n e > a. Select Device Type Revenue Meter b. Select Prtcl WattNde c. Verify that Device ID is set t 2. d. Set the CT value that appears n the CT label: CT Rating <xxxxa>. If CT resets t 0, check the cmmunicatin as described in step b f verify the cnnectin:belw. e. Fr a meter installed at the grid cnnectin pint select Meter Func. Exprt+Imprt. E x p r t + I m p r t E x p r t C n s u m p t i n P r d u c t i n I m p r t N n e The selected ptin is displayed in the RS485 Cnf screen as <E+I>. 4. Select Cmmunicatin RS485-1 Cnf Device Type Multi Devices Battery 1. The battery cnfiguratin screen is displayed: D e v i c e T y p e < B A T > P r t c l < T 7 4 B a t t e r y > D e v i c e I D < 2 4 > B a t t e r y I n f < > -StrEdge Interface Installatin Guide MAN

25 Cnfiguring the RS485 Bus fr Battery and Meter Cnnectin 5. Select Device Type Battery Pack. 6. Select the battery prtcl and ID: Battery type Prtcl Device ID Tesla Pwerwall T74 Battery 24 LG Chem RESU LG Battery T verify battery cnnectin, select Battery Inf and check that the battery infrmatin is displayed. If nt, check the wiring t the battery: S N : < s e r i a l # > M d e l : < X X X X X X > R a t e d P W R [ k W H ] : N / A F W V e r. < X X X X X > Make sure t have the battery serial number and firmware versin at hand whenever cntacting supprt. T verify the cnnectin: 1. Turn the StrEdge Interface ON/OFF switch t ON. 2. Press the inverter external LCD light buttn t display the status screens ne after the ther: a. Check the RS485 cmmunicatin status: w w w w w w w w D e v P r t # # R S < M L T > < 0 2 > < 0 2 > The MLT under Dev dentes that the cnfiguratin is fr multiple devices. The number under Prt (prtcl) shuld display the number f cnfigured devices. The number under ## shuld display the number f detected devices. The abve screen shws an example f 2 devices n the same bus (fr example: meter and battery). If the number f devices under Prt des nt match the number under ##, refer t Trubleshting n page 27. b. Check the meter(s): In the meter(s) status screen check that the status is OK. The fllwing is an example f the status f an Exprt (r Exprt+Imprt) meter: E x p r t M e t e r S t a t u s : < O K / E r r r # > P w e r [ W ] : E n e r g y [ W h ] : x x x x x. x X X X X X. X If Cmm. Errr appears, refer t Trubleshting n page 27. c. Check the battery infrmatin: identificatin, charging status and pwer, and the perating mde. B S N : X X X X X X X X X I D : 2 4 S O E : 8 9 % W W W W P W R : 2 W T t a l : < x > W h S t a t e : C h a r g i n g If Cmm. Errr appears, refer t Trubleshting n page StrEdge Interface Installatin Guide MAN

26 Cnfiguring Maximum Self-cnsumptin This sectin describes the StrEdge applicatins and hw t cnfigure the system. Maximize Self-cnsumptin (MSC) In this mde, the battery is autmatically charged and discharged t meet cnsumptin needs. The battery has tw states: OFF the battery is in standby ON the battery is cntrlled fr maximized self-cnsumptin Battery OFF perids can be cnfigured t extend battery lifetime by minimizing the number f shallw discharges (fr example at nighttime r during the winter). T set up maximize self-cnsumptin: 1. Enter Setup mde, scrll dwn t the Pwer Cntrl menu and select it. A menu similar t the fllwing is displayed: G r i d C n t r l < E n > E n e r g y R R C R C n f. 2. Select Energy Manager. The fllwing screen is displayed: L i m i t C n t r l < D i s > E n e r g y C t r l < D i s > A d v a n c e d Limit Cntrl: Fr pwer limitatin (including exprt limitatin) cnfiguratin. This ptin can be used in parallel t energy cntrl. Fr mre infrmatin refer t. Energy Cntrl: The methd by which t manage the energy. 3. Select Energy Ctrl.. The fllwing is displayed, shwing the SlarEdge applicatins: M a x S e l f - c n s u m e T i m e f U s e D i s a b l e M a n a g e r R e a c t i v e P w r C n f. A c t i v e P w r C n f. P h a s e B a l a n c e < D i s > W a k e u p C n f. P ( f ) A d v a n c e d L a d D e f a u l t s Max Self-cnsume (MSC): Maximize Self-cnsumptin Time f Use (TOU): Charge/Discharge Prfile Prgramming Disable: N energy cntrl, that is, the battery is nt used 4. Fr maximizing self cnsumptin, select Max Self-Cnsume. The Energy Manager screen changes t display the fllwing: L i m i t C n t r l < D i s > E n e r g y C t r l < M S C > S e t O p e r a t i n S t r a g e C t r l Chapter 3: System Cnfiguratin -StrEdge Interface Installatin Guide MAN

27 Prfile Prgramming (fr time-f-use arbitrage) 5. Optinally, set the battery OFF perids as fllws: a. Select Set Operatin. A list is displayed, allwing 12 mnthly prfile setup: J a n < O N > F e b < O N > M a r < O N > A p r < O N > b. Select a mnth. A list f ptins is displayed. S t a r t T i m e < 0 0 : 0 0 > E n d T i m e < 0 0 : 0 0 > A l w a y s O N A l w a y s O F F c. Select ne f the ptins: Select Always OFF t avid battery usage entirely (fr example during winter) Set Start Time and End Time t set battery usage in specific hurs and avid usage during specific hurs thrughut the mnth (fr example at night). This sets the perids during which the battery will be in the OFF state. Select Always ON t use battery at all times fr charging/ discharging. Prfile Prgramming (fr time-f-use arbitrage) In this mde, the StrEdge system perates accrding t a cnfigured charge/ discharge prfile. This applicatin is cvered in a separate applicatin nte available at and_cnfiguratin_guide.pdf. Starting-up the System Upn installatin and cnfiguratin cmpletin, the pwer ptimizers shuld be paired t the inverter.clse the inverter cver and perfrm pairing as described in the installatin guide prvided with yur inverter. 26 StrEdge Interface Installatin Guide MAN

28 Appendix A: Trubleshting Appendix A: Trubleshting This appendix describes hw t trublesht StrEdge related errrs. Cmmunicatin Trubleshting When a battery and a meter are cnnected (2 devices cnnected t the same bus), the fllwing shuld appear in the Cmmunicatin status screen: w w w w w w w D e v P r t # # R S < M L T > < 0 2 > < 0 2 > Z i g B e e < > < - - > < - - > Device type, number and prtcl are displayed incrrectly If ne r mre f the fllwing ccurs, the meter(s) r the battery are nt cmmunicating with the inverter: If Dev is nt MLT (Multi), the system is nt pre-cnfigured and requires full cnfiguratin. Cnfigure the system as described in Cnfiguring the RS485 Bus fr Battery and Meter Cnnectin n page 23. If ## < 02, the meter and/r the battery are nt cnfigured crrectly. Check the cnfiguratin. If Prt < 02, the meter and/r the battery is nt cmmunicating crrectly. Check the cnfiguratin and wiring cnnectin. If Prt = ## the battery and meter are cnfigured and cmmunicating prperly. Trubleshting Ethernet Cmmunicatin When using Ethernet cmmunicatin, use the Server Cmmunicatin Status windw t identify the lcatin f the errr: S e r v e r : L A N < S _ O K > S t a t u s : < O K > x x x x x x x x < E R R O R M E S S A G E > xxxxxxxx is a string f 1s and 0s shwing an eight-bit cmmunicatin cnnectin status. 1 indicates OK and 0 indicates an errr. Bit Lcatin 1st Errr Message LAN Discnnected Cause and Trubleshting Physical cnnectin fault. Check the cable pinut assignment and cable cnnectin. Refer t Creating an Ethernet (LAN) Cnnectin in the inverter installatin guide. 2nd DHCP Failed, r Invalid DHCP Cnfig IP settings issue. Check the ruter and cnfiguratin. Cnsult yur netwrk IT. 3rd Gateway Ping Failed Ping t ruter failed. Check the physical cnnectin t the switch/ruter. Check that the link LED at the ruter /switch is lit (indicating phy-link). If OK - cntact yur netwrk IT, therwise replace the cable r change it frm crss t straight cnnectin. -StrEdge Interface Installatin Guide MAN

29 Meter Trubleshting Bit Lcatin Errr Message Cause and Trubleshting 4th G Server Ping Failed Ping t ggle.cm failed. Cnnect a laptp and check fr internet cnnectin. If internet access is unavailable, cntact yur IT admin r yur internet prvider. 5th 6th 7th 8th Server x Ping Failed Tcp Cnnect. Failed Meter Trubleshting Ping r cnnectin t SlarEdge server failed.. Check the SlarEdge server address, under LAN Cnf submenu: Address: prd.slaredge.cm Prt: Check with yur netwrk administratr whether a firewall r anther device is blcking transmissin. When a meter is cnnected, there will be a status screen fr each meter functin. The fllwing is an example f the exprt meter functin status: <OK> is nt displayed If <OK> is nt displayed in the Status line f the status screens, the meter is nt cmmunicating with the inverter cmmunicatin bard. Check the fllwing: There are n lse cnnectins at the inverter cmmunicatin bard and at the meter. The wiring between the 4-pin terminal blck n the meter and the RS485 terminal blck n the StrEdge Interface is crrect (refer t Figure 19). An errr message is displayed If Errr 185 Meter Cmm. Errr is displayed in the meter status screen, verify prper cnnectin f: The RS485 cables and cnnectrs The AC cnnectin f the meter Pwer [Wh] Imprt value is nt advancing If the inverter is nt prducing pwer, and there is pwer cnsumptin by the lads, check the fllwing: The meter status LEDs are lit. If the LEDs are all OFF, the meter is nt cnnected t a pwer surce. Check the meter AC cnnectin (10-pin terminal blck) Check that the meter breaker is ON There are n lse cnnectins at the 10-pin AC wiring f the meter. The CT black and white cables are crrectly cnnected t the 6-pin cnnectr n the meter: E x p r t M e t e r S t a t u s : P w e r [ W ] : E n e r g y [ W h ] : < O K / E r r r > White CT wire is cnnected t L1 white Black CT wire is cnnected t L1 black x x x x x. x x x x x x. x CT directin is twards the grid and the green pwer LEDs are ON. If the LEDs are nt green indicating imprt pwer - the CTs are reversed. 28 StrEdge Interface Installatin Guide MAN

30 Appendix A: Trubleshting Battery Trubleshting Figure 21: Meter with The State line in the battery status screen shuld display ne f the fllwing: Charging, Discharging, Idle, Off, Init.: B S N : X X X X X X X X X I D : 2 4 S O E : 8 9 % W W W W P W R : 2 W T t a l : < x > W h S t a t e : C h a r g i n g If Errr 186 Battery Cmm. Errr appears, the battery cmmunicatin is discnnected. Check the fllwing: The RS485 cntrl cnnectin t the battery The cmmunicatin DIP switches settings n the battery The ID DIP switches setting n the battery If the state Idle is displayed instead f Charging/Discharging, check the fllwing: The system cnfiguratin The DC cnnectin If Battery Internal Fault is displayed, refer t the battery dcumentatin supplied with it.the fllwing is an example fault screen. B a t t e r y I n t e r n a l F a u l t < # > ( I D : 2 4 ) < x x x x > < x x x x > Fault # - accrding t battery ID - The Mdbus ID f the battery <xxx> - text -StrEdge Interface Installatin Guide MAN

31 StrEdge Interface LEDs StrEdge Interface LEDs LED lcatin Functinality Trubleshting 12V IN (left f the main bard) 12V OUT (right f the main bard) ON -12V (r 13V) is supplied t the main bard OFF - N pwer t the main bard ON - 12V (r 13V) is supplied t the battery (thermal and lgic) OFF - N pwer supply t the battery N/A N/A Check AC cable is cnnected t the the pwer supply (PSU). Check green LED indicatin n the PSU Check the cable cnnectin between the PSU and the main bard Check that the 12V IN LED is lit Make sure all Cntrl cnnectins between the inverter and battery are crrect Check the RS485 cable t the inverter and battery Check the 12V (thermal and lgic) vltages t the battery Red PSU utput is less than 10V Check the AC cable cnnectin Green PSU utput is OK N/A Figure 22: Pwer Supply LED lcatin 30 StrEdge Interface Installatin Guide MAN

32 Appendix B: Additinal Battery Cnnectins Appendix B: Additinal Battery Cnnectins This appendix prvides additinal ptins fr cnnecting batteries t the StrEdge Interface. Pay attentin t the wire clrs and DIP switch setup f the batteries (refer t DIP Switch Setup n page 18). Make sure the first and last device n the RS485 bus is terminated. Cnnectin with One Battery Tesla Pwerwall1 Figure 23: Cnnectins t Tesla Pwerwall1 battery Type B (single phase inverter) -StrEdge Interface Installatin Guide MAN

33 Tesla Pwerwall1 Figure 24: Cnnectins t Tesla Pwerwall1 battery Type B (HD-Wave inverter) 32 -StrEdge Interface Installatin Guide MAN

34 Tesla Pwerwall1 Figure 25: Cnnectins t Tesla Pwerwall1 Battery Type E (single phase inverter) -StrEdge Interface Installatin Guide MAN

35 Tesla Pwerwall1 Figure 26: Cnnectins t Tesla Pwerwall1 Battery Type E (HD-Wave inverter) 34 -StrEdge Interface Installatin Guide MAN

36 LG Chem RESU7H/RESU10H LG Chem RESU7H/RESU10H Figure 27: Cnnectins t LG Chem RESU7H/RESU10H battery (single phase inverter and StrEdge Interface withut DIP-switches) -StrEdge Interface Installatin Guide MAN

37 LG Chem RESU7H/RESU10H Figure 28: Cnnectins t LG Chem RESU7H/RESU10H battery (single phase inverter and StrEdge Interface with DIP-switches) 36 -StrEdge Interface Installatin Guide MAN

38 Cnnectins with Tw Batteries Cnnectins with Tw Batteries Tesla Pwerwall1 Figure 29: Tw Tesla Pwerwall1 batteries Type B -StrEdge Interface Installatin Guide MAN

39 Tesla Pwerwall1 Figure 30: Tw Tesla Pwerwall1 batteries Type E and Type B 38 -StrEdge Interface Installatin Guide MAN

40 Tesla Pwerwall1 Figure 31: Tw Tesla Pwerwall1 batteries Type E and Type C -StrEdge Interface Installatin Guide MAN

41 DIP-Switch Setup - Pwerwall1 Batteries DIP-Switch Setup - Pwerwall1 Batteries System Cmpnent Cmmunicatin and Terminatin Switches Address Switches Batteries Tesla Pwerwall1 batteries Type B (Figure 23) Tesla Pwerwall1 batteries Type C, E (Figure 25) Mdbus prtcl: Single battery r the battery is the last in the chain (terminatin): S2, S6: Left S1, S5: Dwn S3, S4: UP If the battery is nt the last in the chain (n terminatin): S2, S6: Left S1, S5: Dwn S3, S4: Dwn Terminatin: If the battery is nt the last in the chain: Middle - N terminatin Single battery r the battery is the last in the chain: Bttm - Terminatin (with bias) Mdbus prtcl: Right (RS485) Battery address 1 (ID 24) - lcated clsest t the inverter Switch 1: Right Switch 2: Right Switch 3: Right Battery address 2 (ID 25) Switch 1: Left Switch 2: Right Switch 3: Right Battery 1 - lcated clsest t the inverter (address ID 24): Switch 1: Right Switch 2: Right Switch 3: Right Battery 2 - at the end f chain (address ID 25) : Switch 1: Left Switch 2: Right Switch 3: Right 40 -StrEdge Interface Installatin Guide MAN

42 DIP-Switch Setup - Pwerwall1 Batteries System Cmpnent Cmmunicatin and Terminatin Switches Address Switches Meter SlarEdge Meter (Figure 18) Inverter Inverter cmmunicatin bard (Appendix B) StrEdge Interface StrEdge Interface with DIP switches External 120 Ohm terminatin n the last meter cnnected n the RS485 chain Terminatin: If a meter is installed: SW7 Dwn - N terminatin If a meter is nt installed: SW7 Up - terminatin ON. Cmmunicatin: When using Tesla Pwerwall1 Type B battery -bth switches dwn. Otherwise, bth switches always up Meter 1 address: Switch 1: Up Other: Dwn Meter 2 address: N/A N/A Switch 2: Up Other: Dwn -StrEdge Interface Installatin Guide MAN

43 DIP-Switch Setup - Pwerwall1 Batteries Figure 32: Tesla Pwerwall1 battery Type B DIP switches Figure 33: Tesla Pwerwall1 battery Type C/E DIP switches 42 -StrEdge Interface Installatin Guide MAN

44 Appendix C: StrEdge Interface Technical Specificatins Appendix C: StrEdge Interface Technical Specificatins BATTERY DC INPUT SESTI-S1 SESTI-S2 Unit Number f Batteries per Interface fr high capacity 1 Cmpatible Batteries LG Chem RESU7H; Tesla Pwerwall 1 Tesla Pwerwall 1 (type B+B) LG Chem RESU10H 2 fr high pwer and high capacity Tesla Pwerwall 1 2 Tesla Pwerwall 2 Tesla Pwerwall 2 Max Input Vltage 1000 Vdc Max Input Current Adc DC Fuses n Plus and Minus 3 12A (field replaceable), SB type 600V 25A (field replaceable), SB type 600V ADDITIONAL FEATURES Battery Cmmunicatin Interface Meter Cmmunicatin Interface Battery auxiliary pwer (thermal and cntrl) Pllutin degree classificatin (inside/ utside) RS485 RS485 Yes, 12V / 53W Maximum altitude rating 2000 m Overvltage Categry III STOREDGE INTERFACE POWER SUPPLY AC Input Vltage (Nminal) 220 / 230 Vac AC Input Vltage Range Vac AC Frequency (Nminal) 50 / 60 ± 5 Hz Max AC Input Current 300 ma INSTALLATION SPECIFICATIONS 2/ 3 AC input gland cable diameter / wire crss sectin 6-13mm / 1-2.5mm 2 DC input (frm the battery) 1 MC4 pair DC utput (t the inverter) 1 MC4 pair Dimensins (HxWxD) x 316 x mm 1Fr mre batteries per Interface, cntact SlarEdge. 2Any cmbinatin f B, C, E fr high pwer and high capacity ther than B+B fr high capacity nly. 3Fuse replacement kits are available frm SlarEdge r yu can use ther fuses with identical ratings. -StrEdge Interface Installatin Guide MAN

45 Appendix C: StrEdge Interface Technical Specificatins SESTI-S1 SESTI-S2 Unit Weight 3 kg Min - Max Operating Temperature Humidity (nn-cndensing) < 95% Prtectin Rating IP65 Installatin Wall munted -20 t +50 C Figure 34: StrEdge Interface dimensins 44 StrEdge Interface Installatin Guide MAN

46