HygroFlex HF5 Humidity Temperature Transmitters. User Guide

Transcription

1 Page 1 f 36 HygrFlex HF5 Humidity Temperature Transmitters User Guide

2 Page 2 f 36 Table f cntents 1 Overview Mechanical cnfiguratins and dimensins Supply vltage up t 40 VDC / 28 VAC Supply vltage VAC Mdels with USB r Ethernet interface General descriptin Pwer supply ptins Measured parameters Calculated parameters Analg utput signals Digital utputs Service cnnectr Prbe HW4 sftware versin cmpatibility User cnfigurable settings and functins Functin verview Interactin between the HF5 and prbe functins Analg utput signal type (except HF52) Mechanical installatin General guidelines HF5 enclsure Installatin f the HF5 type D (thrugh wall munt) Installatin f the HF5 type W (surface munt) Electrical installatin General wiring guidelines Guidelines fr RS-485 wiring Cable grip and cable specificatins Wiring Operatin HF5 analg utputs HF5 digital utputs Display and keypad ptin Internal menu (ptinal keypad and display) Displayed parameters (ptinal keypad and display) Maintenance Service cable Lcatin f the service cnnectr (mini USB type) Peridic calibratin check f the prbe Cleaning r replacing the prbe dust filter Validatin f the utput signals transmissin Firmware updates Technical data Specificatins Dew pint accuracy Accessries Supprting dcuments Dcument releases... 36

3 Page 3 f 36 Applicability: This manual applies t the fllwing HF5 series transmitters: 2-wire lp pwered mdels (HF52) with firmware versin 1.6 All ther mdels with firmware versin 2.x, where 2.x can be 2.0, 2.1, etc. Changes t the last digit f the versin number reflect minr firmware changes that d nt affect the manner in which the instrument shuld be perated. 1 Overview The HygrFlex HF5 transmitter series is designed fr fixed installatin in applicatins where high measurement accuracy is required and can be used with any f the HygrClip 2 plug-in prbes. The wide assrtment f HygrClip 2 humidity-temperature prbes can meet almst any applicatin requirement. The HygrClip 2 prbes feature well prven, durable sensrs. Digital signal prcessing within the prbe ensures cnsistent prduct perfrmance and als facilitates the task f field maintenance with features such as ptentimeter-free calibratin, ht-swapping f the prbe, etc. Main features f the HF5 series: Interchangeable, plug-in HygrClip 2 prbe (sld separately) Prbe separatin: up t 5 m / 16.4 ft (100 m / 330 ft with a digital signal bster) Relative humidity, temperature, dew pint r ther psychrmetric parameter %RH and -100 t 200 C (-148 t 392 F) - depending n prbe mdel Accuracy: ± 0.8%RH and 0.1ºC / 0.2ºF Analg utputs nly, analg and digital utputs cmbined r digital utputs nly User cnfigurable settings Calculatin f psychrmetric parameters such as the dew r frst pint Humidity temperature calibratin and adjustment 1) Simulatr mde Autmatic humidity sensr test and drift cmpensatin 1) Sensr failure mde 1) Data recrding 1) 1) Except mdel HF52 (2-wire circuit type) The ability fr the user t easily update bth the HF5 and HygrClip 2 prbe firmware means that instruments f the HF5 series can be kept up-t-date regarding any future functinality imprvement.

4 Page 4 f 36 2 Mechanical cnfiguratins and dimensins Depending n the supply vltage, the HF5 uses tw different sizes f enclsure 2.1 Supply vltage up t 40 VDC / 28 VAC Prbe cnnectr Prbe cnnectr NOTE: Vertical munting applies nly t: HF52 type D withut keypad and display HF53 and HF54 type D withut keypad and display r withut digital ptin All ther mdels are munted hrizntally

5 Page 5 f Supply vltage VAC Prbe cnnectr Prbe cnnectr 2.3 Mdels with USB r Ethernet interface USB r Ethernet interface

6 Page 6 f 36 3 General descriptin 3.1 Pwer supply ptins Depending n the circuit type, the HF5 requires the fllwing pwer supply: a) HF52 (2-wire lp pwered, analg utputs): VDC - depending n the lad cnnected t the utput(s). The minimum supply vltage can be determined as fllws: V min = 10 V + (0.02 x Lad*) *Lad resistance in hms. Fr the maximum lad f 500, the minimum supply vltage is 10 + (0.02 x 500) = 20 VDC. With bth utput circuits clsed, the maximum current cnsumptin is 40 ma. b) HF53, HF54 and HF56 (3-wire, analg utputs ptinally cmbined with a digital utput): - HF53: 15 t 40 VDC r 12 t 28 VAC - HF54: 9 t 36 VDC r 7 t 24 VAC, galvanic islatin f the analg utputs and pwer supply - HF56: VAC, galvanic islatin f the analg utputs and pwer supply HF53 and HF54: with bth utput circuits clsed, the typical current cnsumptin is 100 ma. HF56: typical current cnsumptin <50 ma at 85 VAC and <35 ma at 240 VAC Please verify the prduct identificatin label t determine which pwer supply ptin is installed n yur transmitter. c) HF556, HF557 and HF566 (digital utput nly): - HF556: 5 t 40 VDC r 12 t 28 VAC - HF557: PE (pwer ver Ethernet).The HF557 is nt available with a RS-485 interface and can be pwered nly via a LAN. - HF566: VAC Typical current cnsumptin HF556 with USB interface : 100 ma HF556 with Ethernet (TCP/IP) interface and HF557 : 300 ma HF566 USB interface : <50 ma at 85 VAC and <35 ma at 240 VAC HF566 with Ethernet (TCP/IP) interface : <50 ma at 85 VAC and <35 ma at 240 VAC 3.2 Measured parameters The HygrClip 2 prbe used with the HF5 transmitter measures relative humidity with a ROTRONIC Hygrmer IN1 capacitive sensr and temperature with a Pt100 RTD. 3.3 Calculated parameters Using the ROTRONIC HW4 sftware, the HF5 can be cnfigured by the user t calculate ne f the fllwing parameters: Dew pint (Dp) abve and belw freezing Frst pint (Fp) belw freezing and dew pint abve freezing Wet bulb temperature (Tw) Enthalpy (H) Vapr cncentratin (Dv) Specific humidity (Q)

7 Page 7 f 36 Mixing rati by weight (R) Vapr cncentratin at saturatin (Dvs) Vapr partial pressure (E) Vapr saturatin pressure (Ew) Nte: sme f the abve parameters depend n the value f the barmetric pressure. Using the ROTRONIC HW4 sftware, a fixed barmetric pressure value can be specified. Fr instructins see the fllwing HW4 manual: E-M-HW4v3-F Analg utput signals Parameter: With the ROTRONIC HW4 sftware any f the tw analg utput signals can be made t crrespnd t ne f the fllwing: Relative humidity Temperature Calculated parameter Any utput can als be disabled. Output Scale: The scale f each analg utput can be set within the numerical limits f and The D/A cnverters used t generate the analg utput signals feature a 16-bit reslutin. Signal Type: Bth analg utputs prvide the same type f signal. With the exceptin f the HF52 (always 4 20 ma), the type f signal can be selected with the ROTRONIC HW4 sftware t any f the fllwing: 0 20 ma, 4 20 ma, 0 1V, 0 5V r 0 10V (see 4.3). 3.5 Digital utputs Mdels with a digital utput can simultaneusly transmit 3 parameters: relative humidity, temperature and calculated parameter a) RS-485 serial interface Sme mdels f the HF5 are equipped with a RS-485 serial interface. This can be used t cnnect tgether up t 64 devices in a multi-drpped arrangement. In principle, an unlimited number f such netwrks can be mnitred with the HW4 sftware, but each RS-485 multi-drp netwrk is limited t 64 devices. The HF5 can be used either as a slave r a master, withut special cnfiguratin. The master is autmatically the device that is directly cnnected t a PC by means f a USB prt r Ethernet (TCP/IP) prt. RS-485 Cmpatibility: The cmmunicatin prtcl used by the HF5 and ther AirChip 3000 prducts is nt cmpatible with the prtcl used by the previus generatin f ROTRONIC instruments. D nt cnnect legacy prducts and AirChip 3000 prducts t the same RS-485 multi-drp netwrk. b) USB r Ethernet interface Sme mdels f the HF5 are available with a USB r Ethernet interface in additin t the RS-485 interface. In this case the prtectin grade f the HF5 enclsure is n lnger IP65 / NEMA 4 rated.

8 Page 8 f Service cnnectr The service cnnectr is a UART digital interface (Universal Asynchrnus Receiver Transmitter) with a mini- USB type cnnectr. This allws cnnecting the HF5 with a service cable t a PC running the ROTRONIC HW4 sftware. See Maintenance fr the lcatin f the service cnnectr and fr the type f service cable t be used. The service cnnectr is used t cnfigure the HF5 and t and update its firmware with the HW4 sftware. Nte: any digital utput (USB, Ethernet and RS-485) ffers the same functinality as the service cnnectr. 3.7 Prbe The HF5 is cmpatible with all available mdels f HygrClip 2 prbes. Fr detailed infrmatin n the prbes see dcument E-M-HC2 Prbes-V HW4 sftware versin cmpatibility The HF5 versin 2 requires HW4 versin r higher fr full functinality f the Device Manager functin. 4 User cnfigurable settings and functins The HF5 ships cnfigured as specified n the custmer rder. Mdels with analg utputs nly can be installed and used just as any cnventinal humidity and temperature transmitter and mst users will never need t use the HF5 cnfigurable settings and functins. Mdels with a digital utput generally require sme cnfiguratin by the user. Making use f the HF5 and prbe cnfigurable settings and functins is entirely up t the user and the apprpriate settings depend n the user applicatin. We have prvided belw a shrt descriptin f the HF5 and prbe functins and als indicated the factry default settings. 4.1 Functin verview MEASUREMENT ACCURACY AND RELIABILITY (PROBE FUNCTIONS) AirChip 3000 Functins Humidity / temperature adjustment Autmatic humidity sensr test and ptinal drift cmpensatin 1-pint r multi-pint humidity calibratin r adjustment 1-pint r 2-pint temperature calibratin r adjustment Generate a time stamp fr calibratins and adjustments Retain and view last adjustment date and adjustment values Generate calibratin and adjustment prtcls Tests the humidity sensr fr drift caused by cntaminants and can be used t autmatically apply a crrectin. The test is autmatically carried ut at regular intervals f time. Can be cnfigured, enabled, r disabled The humidity sensr status can be verified either with the HW4 sftware r with the instrument display (if available) and is shwn as Gd, SQ-tuned (crrected fr drift) r Bad (defective) Nt available when the prbe is cnnected t a HF52

9 Page 9 f 36 MEASUREMENT ACCURACY AND RELIABILITY (PROBE FUNCTIONS) Data recrding The data recrding functin differs frm a true data lgging functin in the sense that the AirChip 3000 des nt time stamp the data. The data recrding functin can be use t investigate events such as a sensr malfunctin as well as t retrieve data that wuld therwise be lst Start r stp data recrding - up t 2000 value pairs (%RH and temperature). Starting a recrding sessin erases all previusly recrded data The recrding mde and lg interval can be specified When the device is pwered ff, the recrding sessin is paused but nt ended As lng as the recrding sessin has nt been ended, the device autmatically resumes recrding data when pwered up again The recrded data can be dwnladed t a PC with the HW4 sftware, time stamped and viewed Nt available when the prbe is cnnected t a HF52 MEASUREMENT LOOP VALIDATION Functins Simulatr mde Used t make the HF5 generate fixed values fr the humidity, temperature and calculated parameter. Can be cnfigured, enabled r disabled DEVICE SAFEGUARDS Functins Device write prtectin Internal menu access frm keypad Used t prtect the HF5 with a passwrd t prevent unauthrized digital access by a digital user. Can be cnfigured, enabled r disabled Used t prevent accidental changes t the HF5 settings and temperature-humidity adjustment by disabling the MENU key n the ptinal keypad. Can be enabled r disabled PROCESS PROTECTION AND PROTECTION OF OTHER DEVICES AirChip 3000 Functins Limit humidity utput t 100 %RH Out-f-limit value alarm This prbe functin is used t prevent the humidity signal frm exceeding 100 %RH when cndensatin frms n the sensr. Can be enabled r disabled Used t specify the nrmal range fr humidity, temperature and the calculated parameter depending n the user applicatin. Can be cnfigured, enabled r disabled Bad sensr alarm Out-f-limit values trigger a digital alarm which can be als be seen n the ptinal display This is a built-in prbe functin. Cannt be disabled A bad humidity r temperature sensr triggers a digital alarm which can be als be seen n the ptinal HF5 display prvided that the HF5 is set t mnitr prbe alarms

10 Page 10 f 36 PROCESS PROTECTION AND PROTECTION OF OTHER DEVICES Fail safe mde Used t specify a "safe" fixed value fr humidity and fr temperature (HF5 r prbe) in the event f: Lss f cmmunicatin with the prbe (HF5 functin) Sensr failure (prbe functin) Can be cnfigured, enabled r disabled 4.2 Interactin between the HF5 and prbe functins It is imprtant t nte that when used tgether, the HF5 transmitter and HC2 prbe (HygrClip 2) cnstitute a 2-cmpnent system. Each system cmpnent has its wn micrprcessr, firmware and functins. Sme f these functins are unique t each system cmpnent. Other functins are fund in bth cmpnents. HF52 (2-wire, lp pwered transmitter): due t the necessity f limiting the current cnsumptin f the cmbinatin f HF52 and HC2 prbe t less than 4 ma, several prbe functins such as RH sensr test, data recrding and prbe adjustment are nt available with the HF52. The functins and settings f the HF5 transmitter and HygrClip 2 prbe (HC2) perate tgether as indicated belw: Functin / Setting HF5 HC2 Ntes Device prtectin X X Individual t the HF5 and HC2 prbe RS-485 address X X Individual t the HF5 and HC2 prbe Device Name X X Calculatin X X Data refresh rate Simulatr functin X X system X X X User defined descriptin The device name f the HC2 prbe is nt displayed by HW4 and is replaced with the HF5 Input Name Psychrmetric calculatin HF5 setting verrides HC2 prbe setting This setting has n effect n the HF5 and prbe. Depending n the mdel, the data refresh rate is as fllws: HF52: typically 5 s Other mdels: typically 1 s Generates fixed humidity and / r temperature value When enabled, the HF5 settings verride the HC2 prbe settings The HF5 setting verrides HC2 prbe setting regarding the HF5 signals. The HC2 prbe settings still apply when the prbe is used alne Make sure t use the same humidity symbl and the same temperature unit fr bth the HF5 and prbe.

11 Page 11 f 36 Functin / Setting HF5 HC2 Ntes The HF5 settings are independent frm the HC2 prbe settings. Out-f-limits value alarm X X Analg utputs X X The HC2 prbe settings have an effect nly when the HF5 is enabled t mnitr alarms generated by the prbe When ut-f-limit values have been defined fr the same parameter fr bth the HF5 and prbe, any alarm is triggered based n the narrwest set f limits (assuming that the HF5 has been set t mnitr prbe alarms). Parameter and scale The HC2 prbe settings have n effect n the HF5 4.3 Analg utput signal type (except HF52) Bth analg utputs f the HF5 prvide the same type f signal. With the exceptin f the HF52 (always 4 20 ma), the type f signal can be selected with the ROTRONIC HW4 sftware t any f the fllwing: 0 20 ma, 4 20 ma, 0 1V, 0 5V r 0 10V. T select the analg signal type prceed as fllws: Use the apprpriate mdel f service cable (see Maintenance > Service Cable) t cnnect the service cnnectr f the HF5 t a USB prt f a PC with the HW4 sftware installed (HW r higher). Nte that the ROTRONIC USB driver must be installed n the PC as explained in the HW4 manual E-M-HW4v3-Main Start HW4 n the PC and search fr the HF5 (HW4 Main Menu Bar > Devices and Grups > Search fr USB Masters). After finding the HF5 with HW4, expand the device tree t see the HF5 functins. Select Device Manager. Fr further instructins see HW4 manual E-M-HW4v3-F2-005 N adjustment is required after changing the type f utput signal. 5 Mechanical installatin 5.1 General guidelines Relative humidity is extremely dependent n temperature. Prper measurement f relative humidity requires that the prbe and its sensrs be at exactly the temperature f the envirnment t be measured. Because f this, the lcatin where yu chse t install the prbe can have a significant effect n the perfrmance f the instrument. The fllwing guidelines shuld guarantee gd instrument perfrmance: a) Select a representative lcatin: install the prbe where humidity, temperature and pressure cnditins are representative f the envirnment t be measured. b) Prvide gd air mvement at the prbe: air velcity f at least 200 ft/ minute (1 meter/secnd) facilitates adaptatin f the prbe t changing temperature. c) Avid the fllwing: (1) Clse prximity f the prbe t a heating element, a cling cil, a cld r ht wall, direct expsure t sun rays, etc. (2) Clse prximity f the prbe t a steam injectr, humidifier, direct expsure t precipitatin, etc. (3) Unstable pressure cnditins resulting frm excessive air turbulence. d) Immerse as much f the prbe as pssible in the envirnment t be measured.

12 Page 12 f 36 e) Prevent the accumulatin f cndensatin water at the level f the sensr leads. Install the prbe s that the prbe tip is lking dwnward. If this is nt pssible, install the prbe hrizntally. 5.2 HF5 enclsure The HF5 enclsure cnsists f a base and a cver held tgether with 4 screws. T pen the enclsure, use a metric 2.5 mm r 3 mm hex key. Prir t re-assembling the enclsure, verify that the red seal is sitting prperly in its grve n the base. 5.3 Installatin f the HF5 type D (thrugh wall munt) Munting psitin f the enclsure Vertical: HF52 type D withut keypad and display HF53 and HF54 type D withut keypad and display, and withut digital ptin Hrizntal: HF52 type D with keypad and display HF53, HF54 type D with keypad and display r with digital ptin All ther type D mdels Munting hardware The QMA-15 cnsists f a flange and cmpressin fitting and is designed t hld the prbe f the HF5 type D when munted thrugh a wall (see Accessries). The HF5 des nt require any additinal supprt. 5.4 Installatin f the HF5 type W (surface munt) Munting psitin f the enclsure Hrizntal: HF52, HF53, HF54, HF55 and HF56 type W

13 Page 13 f 36 Munting hardware Methd 1: The HF5 is supplied with 2 screws, 2 drywall anchrs and tw rubber washers. The base f the enclsure has 2 screw-wells (see drawing) that are nrmally clsed at the bttm. Use the template prvided with the HF5 t drill munting hles in the wall and insert the drywall anchrs. Place a rubber washer n each screw. Insert a screw in each well and push t pen the bttm f the well. Methd 2: When a DIN-rail (35 mm / 1 3/8 ) is available use part AC5002 (nt included). This is a DIN-rail munting kit cnsisting f 2 clamps that attach t the back f the enclsure with the screws prvided. 6 Electrical installatin 6.1 General wiring guidelines Pwer supply wiring Heavy machinery and instrumentatin shuld nt share the same pwer supply wiring. If this cannt be avided, nise filters and surge prtectrs shuld be used. Mst UPS devices have thse features already integrated. General guidelines fr signal cables The fllwing guidelines are derived frm Eurpean Standard EN fr the transmissin f signals by cpper wires. When planning an installatin, the rules prvided by EN shuld be fllwed under cnsideratin f lcal circumstances t determine the psitin f machines and equipment. All ROTRONIC prducts are tested fr Electrmagnetic Cmpatibility accrding t EMC Directive 2004/106/EG and fllwing Eurpean standards: - EN : 2001, EN : EN : 2005, EN : A11 Whenever the level f electrmagnetic interference is expected t be high, bth the instruments and signal cables shuld be placed as far away as pssible frm the surce f interference. In general, signal cables shuld be installed in bundles r channels / cnduits, separate frm ther cables as indicated in the table belw:

14 Page 14 f 36 Bus signals such as RS485 Data signals fr PCs, printers etc. shielded analg inputs unshielded direct current (<= 60V) shielded prcess signals (<= 25 V) unshielded alternate current (<= 25V) caxial cables fr CRT mnitrs in cmmn bundles r channels / cnduits direct current frm 60 V t 400 V (unshielded) alternate current frm 25V t 400 V (unshielded) in separated bundles r channels / cnduits, withut minimum distance direct and alternate current > 400 V (unshielded) Telephne lines lines leading int EX-rated areas in separated bundles r channels / cnduits, withut minimum distance Lightning prtectin Cabling in areas with a risk f lightning requires a lightning prtectin. Fr cabling undergrund in between buildings, we recmmend the use f special fiber ptic cables. If this is nt pssible, use cpper cables that are suitable fr undergrund installatin. 6.2 Guidelines fr RS-485 wiring See dcument E-DV04-RS485.01: RS485 Netwrk Installatin and Start-up Guidelines 6.3 Cable grip and cable specificatins Depending n the mdel, the HF5 is supplied either with ne r tw M16 sealing cable grips r with ne r tw ½ cnduit adapters. The M16 cable grip prvides effective sealing nly with cables having the prper utside diameter. Preferably, use a cable with an utside diameter f 6 t 7 mm (0.236 t inch) with 18 AWG wires.

15 Page 15 f Wiring HF52: 2-wire, lp pwered transmitter Electrical diagram The maximum permissible cable length cnnecting the HF52 t ther devices is determined by the ttal resistance resulting frm the additin f the cable resistance and that f the devices cnnected in series with the unit. This resistance shuld nt exceed 500 hms. Terminal blck diagram K2-2: T-OUT Temperature utput (+) OUT-2 K2-1: V+ Pwer supply: VDC (+) Nte: cnnect the + f the pwer supply t nly ne f the V+ terminals. The tw terminals marked V+ are internally cnnected. Measuring humidity r temperature nly K1-2: H-OUT Operatin f the HF52 des nt require bth current lps t be clsed. When using the HF52 t measure either humidity nly r temperature nly, clse nly the lp that is being used. Using the ROTRONIC HW4 sftware, any unused utput f the HF52 can be disabled. Relative humidity r dew pint (+) OUT-1 K1-1: V+ Pwer supply: VDC (+)

16 Page 16 f HF53: 3-wire transmitter Electrical diagram fr vltage utputs U B V+ GND B2 OUT1 OUT2 GND The maximum permissible cable length can be determined under cnsideratin f the vltage drp caused by the current flwing t the devices cnnected t the unit. The vltage drp in the cable depends bth n cable resistance and n the equivalent resistance f the devices cnnected in parallel t the unit. The ttal resistance cnnected t each unit utput shuld be at least 1000 hms. Cable resistance shuld nt be mre than 1/1000 f the lad resistance. Electrical diagram fr current utputs U B V+ GND OUT1 OUT2 The maximum permissible cable length, cnnecting the unit t ther devices, is determined by the ttal resistance resulting frm the additin f the cable resistance and that f the devices cnnected in series with the unit. This resistance shuld nt exceed 500 hms. B2 GND Terminal blck diagram (analg utputs nly) Type D and W (hrizntal munt) K1-1: GND K1-2: V+ K1-3: - Pwer supply (-) r neutral (tied with ther GND) Pwer supply: VDC (+) r VAC (Phase) Prtective grund (see nte belw) K2-4: GND K2-3: GND K2-2: OUT2 Grund (tied with ther GND) Grund (tied with ther GND) Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+)

17 Page 17 f 36 Type D (vertical munt) K2-4: GND K2-3: GND K2-2: OUT2 Grund (tied with ther GND) Grund (tied with ther GND) Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) K6-1: GND K6-1: V+ K6-3: - Pwer supply (-) r neutral (tied with ther GND) Pwer supply: VDC (+) r VAC (Phase) Prtective grund (see nte belw) Nte: K1-3 r K6-3 (prtective r earth grund) are nt tied with GND. If s desired, K1-3 r K6-3 can be tied with GND by clsing a slder pad n the PCB

18 Page 18 f 36 Terminal blck diagram (analg utputs and digital ptin) Type D and W (hrizntal munt) K1-1: GND K1-2: V+ K1-3: - Pwer supply (-) r neutral (tied with ther GND) Pwer supply: VDC (+) r VAC (Phase) Prtective grund (see nte belw) K2-4: GND K2-3: GND Grund (tied with ther GND) Grund (tied with ther GND) K2-2: OUT2 Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) K3-4: D- K3-3: D+ RS-485 Bi-directinal TX- / RX - RS-485 Bi-directinal TX+ / RX + K3-2: GND Grund / Pwer supply (-) K3-1: PWR DC (+) VDC (+) (ptinal, see nte belw) Ntes: Terminal K1-3: this terminal (prtective r earth grund) is nt tied with GND. If s desired, K1-3 can be tied with GND by clsing a slder pad n the PCB Terminal blck K3 (RS-485): terminals K3-1 and K3-2 can be used t pwer the HF53 frm a 15 t 24 VDC pwer supply cnnected t the RS-485 main data line. In this case, d nt use terminals K1-1 and pin K1-2 (nrmally used t pwer the HF53). USB r TCP/IP prt: this prt is ptinal Measuring humidity r temperature nly Operatin f the HF53 des nt require bth current lps t be clsed. When using the HF53 t measure either humidity nly r temperature nly, clse nly the lp that is being used. Using the ROTRONIC HW4 sftware, any unused utput f the HF53 can be disabled.

19 Page 19 f HF54: 3-wire transmitter, galvanic islatin f the analg utputs Electrical diagram fr vltage utputs U B V+ GND DC DC OUT1 OUT2 GND The maximum permissible cable length can be determined under cnsideratin f the vltage drp caused by the current flwing t the devices cnnected t the unit. The vltage drp in the cable depends bth n cable resistance and n the equivalent resistance f the devices cnnected in parallel t the unit. The ttal resistance cnnected t each unit utput shuld be at least 1000 hms. Cable resistance shuld nt be mre than 1/1000 f the lad resistance. Electrical diagram fr current utputs U B V+ GND DC DC OUT1 OUT2 The maximum permissible cable length, cnnecting the unit t ther devices, is determined by the ttal resistance resulting frm the additin f the cable resistance and that f the devices cnnected in series with the unit. This resistance shuld nt exceed 500 hms. GND Terminal blck diagram (analg utputs nly)

20 Page 20 f 36 Type D and W (hrizntal munt) K1-1: GND K1-2: V+ K1-3: - Pwer supply (-) r neutral Pwer supply: VDC (+) r VAC (Phase) Prtective grund (see nte belw) K2-4: GND K2-3: GND Grund (tied with ther GND) Grund (tied with ther GND) K2-2: OUT2 Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) Type D (vertical munt) K2-4: GND K2-3: GND Grund (tied with ther GND) Grund (tied with ther GND) K2-2: OUT2 Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) K6-1: GND K6-1: V+ K6-3: - Pwer supply (-) r neutral Pwer supply: VDC (+) r VAC (Phase) Prtective grund (see nte belw) Nte: K1-3 r K6-3 (prtective r earth grund) are nt tied with GND. If s desired, K1-3 r K6-3 can be tied with GND by clsing a slder pad n the PCB (B18)

21 Page 21 f 36 Terminal blck diagram (analg utputs and digital ptin) Type D and W (hrizntal munt) K1-1: GND K1-2: V+ K1-3: - Pwer supply (-) r neutral Pwer supply: VDC (+) r VAC (Phase) Prtective grund (see nte belw) K2-4: GND K2-3: GND Grund (tied with ther GND) Grund (tied with ther GND) K2-2: OUT2 Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) K3-4: D- K3-3: D+ K3-2: GND K3-1: PWR RS-485 Bi-directinal TX- / RX - RS-485 Bi-directinal TX+ / RX + Grund Nt used Ntes: Terminal K1-3: this terminal (prtective r earth grund) is nt tied with GND. If s desired, K1-3 can be tied with GND by clsing a slder pad n the PCB (B18) USB r TCP/IP prt: this prt is ptinal Measuring humidity r temperature nly Operatin f the HF54 des nt require bth current lps t be clsed. When using the HF54 t measure either humidity nly r temperature nly, clse nly the lp that is being used. Using the ROTRONIC HW4 sftware, any unused utput f the HF54 can be disabled.

22 Page 22 f HF556: digital utput Cnnectrs and terminal blck diagram K1-1: GND K1-2: V+ K1-3: - Pwer supply (-) r neutral (tied with ther GND) Pwer supply: 5 40 VDC (+) r VAC (Phase) Prtective grund (see nte belw) K3-4: D- K3-3: D+ K3-2: GND K3-1: PWR RS-485 Bi-directinal TX- / RX - RS-485 Bi-directinal TX+ / RX + Grund / Pwer supply (-) (tied with ther GND) DC (+) VDC (+) (ptinal, see nte belw) Ntes: Terminal K1-3: this terminal (prtective r earth grund) is nt tied with GND. If s desired, K1-3 can be tied with GND by clsing a slder pad n the PCB (B18) Terminal blck K3 (RS-485): terminals K3-1 and K3-2 can be used t pwer the HF55 frm a 15 t 24 VDC pwer supply cnnected t the RS-485 main data line. In this case, d nt use terminals K1-1 and pin K1-2 (nrmally used t pwer the HF55). WARNING: Cnnecting a device t an active Ethernet netwrk can disrupt cmmunicatins n the netwrk. Befre cnnecting the HF5, make sure that it is prperly cnfigured fr yur netwrk.

23 Page 23 f HF557: digital utput, PE (pwer ver Ethernet) This mdel is pwered frm the Ethernet LAN and has n terminal blcks. WARNING: Cnnecting a device t an active Ethernet netwrk can disrupt cmmunicatins n the netwrk. Befre cnnecting the HF5, make sure that it is prperly cnfigured fr yur netwrk HF56: VAC supply vltage Electrical diagram fr vltage utputs ~ AC L AC OUT1 OUT2 AC N DC B2 GND The maximum permissible cable length can be determined under cnsideratin f the vltage drp caused by the current flwing t the devices cnnected t the unit. The vltage drp in the cable depends bth n cable resistance and n the equivalent resistance f the devices cnnected in parallel t the unit. The ttal resistance cnnected t each unit utput shuld be at least 1000 hms. Cable resistance shuld nt be mre than 1/1000 f the lad resistance.

24 Page 24 f 36 Electrical diagram fr current utputs ~ AC L AC OUT1 OUT2 AC N DC B2 GND The maximum permissible cable length, cnnecting the unit t ther devices, is determined by the ttal resistance resulting frm the additin f the cable resistance and that f the devices cnnected in series with the unit. This resistance shuld nt exceed 500 hms. Terminal blck diagram (analg utputs nly) F1: fuse (sldered t PCB) K6-1: - Prtective grund K2-4: GND Grund (tied with ther GND) K6-2 Pwer supply phase: 85 t 240 VAC K2-3: GND Grund (tied with ther GND) K6-3 Pwer supply neutral 85 t 240 VAC K2-2: OUT2 Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) Nte: If s desired, K2-3 and K2-4 can be tied with the prtective grund by clsing slder pad B2 n the PCB

25 USB r TCP/IP E-M-HF5-V2_11 Page 25 f 36 Terminal blck diagram (analg utputs and digital ptin) RS-485 RS485 + USB RS Ethernet K6-1: - Prtective grund K2-4: GND Grund (tied with ther GND) K6-2 K1-3 Pwer supply phase: 85 t 240 VAC Pwer supply neutral 85 t 240 VAC K2-3: GND Grund (tied with ther GND) K2-2: OUT2 Temperature utput (+) K2-1: OUT1 Relative humidity r dew pint (+) Nte: If s desired, K2-3 and K2-4 can be tied with the prtective grund by clsing slder pad B2 n the PCB K3-4: D- RS-485 Bi-directinal TX- / RX - K3-3: D+ RS-485 Bi-directinal TX+ / RX + K3-2: GND Grund (tied with ther GND) K3-1 Nt Used USB r TCP/IP prt: this prt is ptinal Measuring humidity r temperature nly Operatin f the HF56 des nt require bth current lps t be clsed. When using the HF56 t measure either humidity nly r temperature nly, clse nly the lp that is being used. Using the ROTRONIC HW4 sftware, any unused utput f the HF56 can be disabled.

26 USB r TCP/IP E-M-HF5-V2_11 Page 26 f HF566: VAC supply vltage, digital utput nly Terminal blck diagram (analg utputs and digital ptin) RS-485 RS485 + USB RS Ethernet K6-1: - K6-2 K6-3 Prtective grund Pwer supply phase: 85 t 240 VAC Pwer supply neutral 85 t 240 VAC K3-4: D- RS-485 Bi-directinal TX- / RX - K3-3: D+ RS-485 Bi-directinal TX+ / RX + K3-2: GND Grund (tied with ther GND) K3-1 Nt Used USB r TCP/IP prt: this prt is ptinal Grunding (all mdels) We generally recmmend grunding the (-) side f the pwer supply, especially if the electrnics will be subjected t a lw humidity envirnment (35 %RH r less).

27 Page 27 f 36 7 Operatin 7.1 HF5 analg utputs Use the HW4 sftware t cnfigure the analg utputs f the HF5 as desired, cmplete the mechanical and electrical installatin, cnnect the prbe and simply pwer up the HF HF5 digital utputs The digital utputs f the HF5 use the standard RO-ASCII prtcl and d nt ffer any ther ptin. Users wh wish t read the measurement data withut the HW4 sftware shuld cnsult ROTRONIC. The different types f digital interface available with the HF5 are best used with a PC with the HW4 sftware installed (versin r higher). In principle, users shuld be able t use cmmunicatin sftware ther than HW4 t read measurement data frm the HF5. In this case, cmmunicatin is limited t the RDD (data request) and REN (RS-485 address change) cmmands described separately in dcument E-M-AC3000-CP. IMPORTANT: Depending n the type f digital interface, either the PC r the HF5 must be cnfigured by the user as indicated belw. a) USB cnnectin Prir t cnnecting the HF5 t a USB prt yu must install the ROTRONIC USB driver n the PC (available frm the HW4 CD r frm Fr instructins see the HW4 manual E-M-HW4v3- Main ( 7.3) b) Ethernet (TCP/IP) cnnectin Prir t cnnecting the HF5 t an active Ethernet netwrk yu must cnfigure the TCP/IP settings f the HF5 using either the HW4 sftware (versin r higher) r the TCP/IP cnfiguratin tl available frm Fr instructins see the HW4 manual E-M-HW4v3-Main ( 7.4) and technical nte IN-E-TCPIP-Cnf WARNING: Cnnecting a device t an active Ethernet netwrk can disrupt cmmunicatins n the netwrk. Befre cnnecting the HF5, make sure that it is prperly cnfigured fr yur netwrk c) RS-485 serial interface (multi-drp) Instructins fr using the HF5 with a RS-485 netwrk are prvided in the fllwing manuals: E-M-HW4v3-Main ( 7.5), E-M-HW4v3-F2-005 and E-DV04-RS Ntes: Instruments cnnected t the same RS-485 netwrk must use the same baud rate and each instrument must be given a unique RS-485 address (the address requirement applies t the HF5 but nt t its prbe) RS-485 Cmpatibility: The cmmunicatins prtcl used by the HF5 is the RO-ASCII prtcl. This prtcl is nt cmpatible with the prtcl used by the previus generatin f ROTRONIC prducts. D nt cnnect legacy prducts and the HF5 t the same RS-485 multi-drp netwrk.

28 Page 28 f 36 The specificatins f the RS-485 interface are as fllws: Baud rate : Parity : nne Data bits : 8 Stp bits : Display and keypad ptin Except fr the HF52 (2-wire circuit type), the LC display f the HF5 has a backlight. The upper line crrespnds t relative humidity the bttm line crrespnds t temperature. If enabled the third line crrespnds t the calculated Parameter. The display can be cnfigured t shw a trend indicatr n each line: : increasing value : decreasing value In the event f an alarm the display shws the symbl [! ] t the right f the value. Fr instructins abut cnfiguring the display, see the fllwing HW4 manual: E-M-HW4v3-F Internal menu (ptinal keypad and display) Nte: Unauthrized access t the menu can be prevented by disabling the display menu setting (use the HW4 sftware > Device Manager > Display) MENU key: pen / clse menu ENTER key: menu item selectin Mdel HF52 (2-wire circuit type): Main Menu Menu Items Selectins / Infrmatin Ntes Device Settings Device Infrmatin s Cntrast Metric / English LC display cntrast adjustment Trend On / Off Trend indicatin n the display Versin Serial Nbr Address Firmware versin Serial number RS-485 address Menu navigatin keys + / - Change value up / dwn

29 Page 29 f 36 Main Menu Menu Items Selectins / Infrmatin Ntes Prbe Infrmatin Other HF5 mdels: Type Device type Name Device name User defined Versin Serial Nbr Address Firmware versin Serial number RS-485 address Name Device name User defined Main Menu Menu Items Selectins / Infrmatin Ntes Device Settings Device Infrmatin Prbe Infrmatin Humidity Adjust Temperature Adjust s Metric / English Back Light Key Press / On / Off Display backlight mde Cntrast LC display cntrast adjustment Trend On / Off Trend indicatin n the display Versin Serial Nbr Address Type Firmware versin Serial number RS-485 address Device type Name Device name User defined Versin Serial Nbr Address Firmware versin Serial number RS-485 address Name Device name User defined SensrTest Humidity sensr status Off / Gd / SQ-Tuned / Bad Recrd On / Off Data recrding by the prbe (max values) RefValue Humidity reference value ± 0.1 %RH steps Acquired <Acquire> <Delete> <Adjust> Number f cal. pints in prbe memry Save cal. pint t prbe memry Erases all calibratin pints RefValue Temperature reference value ± 0.1 C steps <Adjust> Effect depends n number f calibratin pints 1-pint adjustment nly (ffset) Recrd: bth the recrding mde (start / stp and the lg interval cannt be changed frm the menu and are as cnfigured with the ROTRONIC HW4 sftware

30 Page 30 f 36 SensrTest: Off means that the humidity sensr has nt been tested due t the cnfiguratin settings f the test. Fr a descriptin f the autmatic humidity sensr test and drift cmpensatin (SQ-tuning) see dcuments E-T-AC3000-DF-V1 and E-M-HW4v3-F Displayed parameters (ptinal keypad and display) When the menu is nt active, press the ENTER key t change which parameters are shwn n the display: Relative humidity and temperature Relative humidity, temperature and calculated parameter (when the calculated parameter is enabled) 8 Maintenance 8.1 Service cable IMPORTANT: Use service cable AC3009 with all 2-wire, lp pwered transmitters. This cable pwers up the transmitter via the service cnnectr. D nt use any ther methd fr pwering the transmitter when using this cable AC3009 as this will create a grund lp and damage the transmitter. Fr the same reasns d nt use cable AC3006 with a 2-wire, lp pwered transmitter. Use service cable AC3006 with all 3-wire transmitters as well as with digital mdels. This cable des nt prvide pwer t the transmitter and the transmitter shuld pwered separately when using this cable Bth cables AC3006 and AC3009 cnvert UART (service cnnectr) t USB and are used t cnnect the transmitter t a USB prt f a PC running the ROTRONIC HW4 sftware. Prir t using any f these cables, the ROTRONIC USB driver must be installed n the PC. Bth the driver and the installatin instructins (dcument E-M-HW4v3-Main) are lcated n the HW4 CD. 8.2 Lcatin f the service cnnectr (mini USB type) WARNING: the service cnnectr is a UART interface with a mini-usb cnnectr type. D nt cnnect the service cnnectr directly t the USB prt f a PC r hub. The service cnnectr can be accessed withut pening the enclsure after remving the small red sealing cver. HF32 Hrizntal munt: the service cnnectr is lcated at the bttm f the enclsure (black arrw) Vertical munt: the service cnnectr is lcated either n the left side r n the right side f the enclsure.

31 Page 31 f Peridic calibratin check f the prbe Bth the Pt 100 RTD temperature sensr used in the prbe and assciated electrnics are very stable and shuld nt require any calibratin after the initial factry adjustment. Lng term stability f the ROTRONIC Hygrmer humidity sensr is typically better than 1 %RH per year. Fr maximum accuracy, calibratin f the prbe shuld be verified every 6 t 12 mnths. Applicatins where the prbe is expsed t significant pllutin may require mre frequent verificatins. Nte: the HygrClip 2 prbe cannt be adjusted when cnnected t mdel HF52 (2-wire circuit type) a) Prcedure fr adjusting the prbe using the ptinal keypad (except mdel HF52) Temperature adjustment The keypad f the HF5 allws nly a 1-pint adjustment f temperature. The effect f a 1-pint temperature adjustment is t add the same ffset t all measured values. When temperature is stable, press the MENU key t shw the internal menu n the display Use the (-) key t select Temperature Adjust and press the ENTER key Make sure that the text line beginning with RefValue is highlighted and press the ENTER key Use the (+) r (-) key t change the reference value t match the temperature reference Use the (-) key t highlight the Adjust text line and press the ENTER key The HF5 cnfirms the adjustment with the message Adjust OK Press the MENU key twice t exit the menu and return the HF5 t nrmal peratin Ntes: Any temperature adjustment shuld be dne prir t adjusting humidity. The calibratin pint is autmatically deleted frm the prbe memry after an adjustment Because the HF5 has n real time clck, the date f the adjustment is nt written t the prbe. If retaining the adjustment date is imprtant, use the HW4 sftware t adjust the prbe. Humidity adjustment The keypad f the HF5 allws a multi-pint adjustment f humidity. The effect f a humidity adjustment depends n the number f calibratin pints present in the prbe memry prir t the adjustment: - ne calibratin pint: ffset added t all measured values - tw calibratin pints: ffset and slpe - three r mre calibratin pints: ffset, slpe, linearity Fr maximum accuracy use at least 3 t 4 calibratin pints distributed equally acrss the measurement range f interest. The calibratin pints (maximum 100) can be acquired in any rder but we recmmend ging frm lw humidity values t high humidity values. When humidity is stable, press the MENU key t shw the internal menu n the display Use the (-) key t select Humidity Adjust and press the ENTER key Make sure that the text line beginning with RefValue is highlighted and press the ENTER key Use the (+) r (-) key t change the reference value t match the reference humidity Use the (-) key t highlight the Acquire text line and press the ENTER key Nte that the Acquired cunter is incremented by 1 (number f calibratin pints in the prbe memry) When all calibratin pints have been acquired, use the (-) key t highlight the Adjust text line and press the ENTER key. D nt adjust the prbe befre having acquired all calibratin pints. The HF5 cnfirms the adjustment with the message Adjust OK

32 Page 32 f 36 Ntes: Press the MENU key twice t exit the menu and return the HF5 t nrmal peratin All calibratin pints are autmatically deleted frm the prbe memry after an adjustment Instructins fr using the ROTRONIC calibratin devices and humidity standards are prvided in dcument E-M-CalBasics Because the HF5 has n real time clck, the date f the adjustment is nt written t the prbe. If retaining the adjustment date is imprtant, use the HW4 sftware t adjust the prbe. b) Using the HW4 sftware t adjust the prbe cnnected t a HF5 (except mdel HF52): Use the apprpriate mdel f service cable (see Maintenance > Service Cable) t cnnect the service cnnectr f the HF5 t a USB prt f a PC with the HW4 sftware installed. Nte that the ROTRONIC USB driver must be installed n the PC as explained in the HW4 manual E-M-HW4v3- Main. In the case f the HF55, a cnnectin with the PC can be established via the USB (ROTRONIC USB driver) r Ethernet interface. Start HW4 n the PC and search fr the HF5 (HW4 Main Menu Bar > Devices and Grups > Search fr USB Masters). After finding the HF5 with HW4, expand the device tree t see the HF5 functins. Select Prbe and Prbe Adjustment. Fr further instructins see HW4 manual E-M-HW4v3-A Cleaning r replacing the prbe dust filter See dcument E-M-HC2 Prbes-V1 8.5 Validatin f the utput signals transmissin If s desired, transmissin f the HF5 utput signals can be validated by using the simulatr functin. The HW4 sftware is required t enable and cnfigure this functin. When this functin is enabled the HF5 generates fixed digital and analg signals as specified by the user. Fr instructins see dcument E-M-HW4v3-F Firmware updates Firmware updates will be available n the ROTRONIC website fr dwnlading. Firmware files are given a name that shws bth t which device the file applies and the versin number f the firmware. All firmware files have the extensin HEX. Prcedure fr updating the firmware: Use the apprpriate mdel f service cable (see Maintenance > Service Cable) t cnnect the service cnnectr f the HF5 t a USB prt f a PC with the ROTRONIC HW4 sftware installed. Nte that the ROTRONIC USB driver must be installed n the PC as explained in the HW4 manual E-M-HW4v3-Main. In the case f the HF55, a cnnectin with the PC can be established via the USB (ROTRONIC USB driver) r Ethernet interface. Cpy the firmware update file frm the ROTRONIC website t the PC. Start HW4 sftware n the PC and search fr the HF5 (HW4 Main Menu Bar > Devices and Grups > Search fr USB Masters). After finding the HF5, expand the device tree t see the HF5 functins. Select Device Manager. In the Device Manager menu bar select Tls > Firmware Update. Fr instructins see dcument E-M-HW4v3-F2-005

33 Page 33 f Technical data 10.1 Specificatins General HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Device type Humidity temperature transmitter with analg utput signals Circuit type 2-wire, lp pwered 3-wire Mechanical cnfiguratin types D and W Humidity temperature transmitter with analg utput signals and ptinal digital utput Humidity temperature transmitter with digital utput Pwer supply and cnnectins HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Supply vltage (VDD) 10 28VDC V min = 10 V + (0.02 x Lad*) *Lad resistance in hms. HF53: VDC r VAC HF54: 9 t 36 VDC r 7 t 24 VAC Galvanic islatin HF56: 85 t 240 VAC 47 t 63 Hz Galvanic islatin Typical current cnsumptin 2 x 20 ma HF53 / HF54: 100 ma HF56: < 50 ma at 85 VAC < 35 ma at 240 VAC HF556: 5 40 VDC r VAC HF557: PE HF566: 85 t 240 VAC 47 t 63 Hz HF 556: with USB interface: 100 ma HF556 / HF557 with Ethernet interface: 300 ma HF566: < 50 ma at 85 VAC < 35 ma at 240 VAC Electrical cnnectins Terminal blcks and 1 x M16 cable grip r ½ cnduit adapter HF53 / HF54:Terminal blcks and 1 x M16 cable grip r ½ cnduit adapter HF56: Terminal blcks and 2 x M16 cable grip r ½ cnduit adapter HF556: Cnnectr (USB r Ethernet), terminal blcks (pwer supply and RS-485) and 1 x M16 cable grip r ½ cnduit adapter HF557: Ethernet Cnnectr HF566: Cnnectr (USB r Ethernet), terminal blcks (pwer supply and RS-485) and 2 x M16 cable grip r ½ cnduit adapter Plarity prtectin Fuse Prtective dide n V+ (except HF56, HF57 and HF58) HF56 / HF566: 2A fuse, sldered t PCB Humidity and temperature measurement See dcument E-M-HC2 Prbes > Specificatins

34 Page 34 f 36 Calculated parameters HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Psychrmetric calculatins Dew pint (Dp) abve and belw freezing Frst pint (Fp) belw freezing and dew pint abve freezing Wet bulb temperature (Tw) Enthalpy (H) Vapr cncentratin (Dv) Specific humidity (Q) Mixing rati by weight (R) Vapr cncentratin at saturatin (Dvs) Vapr partial pressure (E) Vapr saturatin pressure (Ew) Start-up time and data refresh rate HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Start-up time 14 s (typical) 3.s (typical) 3 s (typical) Data refresh rate 5 s (typical) 1 s (typical) 1 s (typical) Cnfigurable analg utputs HF52 HF53 / HF54 / HF56 Output 1 Parameter Scale Output 2 Parameter Scale Output 1 and Output 2 Signal type User cnfigurable scaling limits Shrt circuit tlerant Can be made t crrespnd t any parameter User cnfigurable with the ROTRONIC HW4 sftware User cnfigurable with the ROTRONIC HW4 sftware Can be made t crrespnd t any parameter User cnfigurable with the ROTRONIC HW4 sftware User cnfigurable with the ROTRONIC HW4 sftware 4 20 ma engineering units Yes 0 20 ma 4 20 ma 0 1 V 0 5 V 0 10 V (user cnfigurable) Maximum external lad 500 Ω 500 Ω (current utput) Minimum external lad 0 Ω 1000 Ω (vltage utput) 0 Ω (current utput) Digital interface HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Interface type N/A Optinal: RS-485 r USB + RS-485 r Ethernet + RS-485 HF556/ HF566: RS-485 r USB + RS-485 r Ethernet + RS-485 HF557: Ethernet Service cnnectr HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Interface type UART (Universal Asynchrnus Receiver Transmitter) Maximum service cable length 5 m (16.4 ft) General specificatins HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Optinal display LC, 1 r 2 decimals reslutin, n backlight, trend and alarm indicatin LC, 1 r 2 decimals reslutin, backlight, trend and alarm indicatin

35 Page 35 f 36 Husing material ABS Husing prtectin grade IP 65 IP 65 (except mdels with USB r Ethernet) Physical dimensins Weight See Mdels 250 g (8.8 z) Mdels with small enclsure: 250 g (8.8 z) Mdels with large enclsure: 540 g (1 lb 3 z) Cnfrmity with standards HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 CE / EMC immunity Slder type Fire prtectin class FDA / GAMP directives EMC Directive 2004/108/EG: EN : 2001, EN : 2005 EN : 2005, EN : A11 Lead free (RHS directive) Crrespnds t UL94-HB cmpatible Envirnmental limits HF52 HF53 / HF54 / HF56 HF556 / HF557 / HF566 Strage and transit Operating limits at electrnics Temperature limits at prbe Maximum humidity at sensr Maximum air velcity at prbe Critical envirnments C / C (mdels with display), %RH, nn cndensing C / C (mdels with display), %RH, nn cndensing Depends n prbe mdel 100 %RH up t 80 C (176 F) 75 %RH at 100 C (212 F) 45 %RH at 125 C (260 F) 15 %RH at 150 C (302 F) 20 m/s (3,935 ft /min) Humidity sensr: as per DV Critical chemicals 10.2 Dew pint accuracy See dcument E-M-HC2 Prbes > Dew pint accuracy 11 Accessries Fr accessries and parts such as the HW4 cnfiguratin sftware, service cables, calibratin accessries and spare dust filters, please see dcument E-M-HC2-accessries 12 Supprting dcuments Dcument File Name E-M-HC2 Prbes-V1 Cntents HygrClip 2 (HC2) Humidity Temperature Prbes, User Guide E-M-HC2-accessries Accessries and parts fr prbes, indicatrs and transmitters E-T-AC3000-DF-V1 AirChip 3000 and Main Functins E-M-HW4v3-DIR E-M-HW4v3-Main List f the HW4 manuals HW4 sftware versin 3: General instructins and functins cmmn t all devices

36 Page 36 f 36 Dcument File Name E-M-HW4v3-F2-005 Cntents HW4 sftware versin 3: Device Manager - HF5 transmitter E-M-HW4v3-F2-001 HW4 sftware versin 3: Device Manager HC2 prbe series E-M-HW4v3-A2-001 HW4 sftware versin 3: Prbe Adjustment functin AirChip 3000 devices E-M-HW4v3-DR-001 HW4 sftware versin 3: Data Recrding Functin AirChip 3000 Devices E-M-AC3000-CP AirChip 3000 Cmmunicatin Prtcl Optins E-DV04-RS E-M-TCPIP-Cnf E-M-CalBasics E-T-HumiDefs RS485 Netwrk Installatin and Start-up Guidelines Cnfiguratin prcedures fr ROTRONIC devices with Ethernet (TCP/IP) interface Temperature and humidity calibratin basics Instructins fr using the ROTRONIC humidity standards Humidity Definitins Nte: All dcument file names have an extensin crrespnding t the dcument release number. This extensin is nt shwn in the abve table. 13 Dcument releases Dc. Release Date Ntes _10 Dec. 14, 2010 Original release _11 Oct. 28, 2011 Updated this dcument regarding the mdel f service cable t be used with 2-wire and 3-wire mdels.