FCC Notice. ZTS-110 Z-Thermostat USER MANUAL. Warnings. Caution

Transcription

1 FCC Ntice This device cmplies with Part 5 f the FCC rules. Operatin is subject t the fllwing tw cnditins: () this device may nt cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired peratin. NOTE: This equipment has been tested and fund t cmply with the limits fr a Class B digital device, pursuant t Part 5 f the FCC Rules. These limits are designed t prvide reasnable prtectin against harmful interference in a residential installatin. This equipment generates, uses and can radiate radi frequency energy and, if nt installed and used in accrdance with the instructins, may cause harmful interference t radi cmmunicatins. Hwever, there is n guarantee that interference will nt ccur in a particular installatin. If this equipment des cause harmful interference t radir televisin receptin, which can be determined by turning the equipment ff and n, the user is encuraged t try t crrect the interference by ne r mre f the fllwing measures: - Rerient r relcate the receiving antenna. - Increase the separatin between the equipment and receiver. - Cnnect the equipment int an utlet n a circuit different frm that t which the receiver is cnnected. - Cnsult the dealer r an experienced radi/tv technician fr help. Ntice : Changes r mdificatins t this unit nt expressly apprved by the party respnsible fr cmpliance culd vid the user authrity tperate the equipment. Warnings - D nt mdify the unit in any way. - Risk f fire. - Risk f electrical shck. - Risk f burns. - D nt dispse f electrical appliances and unsrted municipal waste, use separate cllectin facilities. Cntact yur lcal gvernment fr infrmatin regarding the cllectin systems available. - There is n user serviceable parts in this unit. Cautin - Risk f explsin if battery is replaced by an incrrect type. - Dispse f used batteries accrding t the instructins. Printed in China 39 F ZTS-0 Z-Thermstat USER MANUAL Firmware Versin: 2.06

2 Table f Cntents Intrductin 2 Features list 3 Glssary 4 Physical Installatin and Wiring 5 Installatin Lcatin 6 Physically Installing the Thermstat 6 Wiring 7 Jumper Settings fr ELECTH-HPUMP and HE-HG 9 Setup and Operatins Prduct Overview Descriptin f Functin Keys Activate/Deactivate Easy Mde Temperature Scale selectin in Easy Mde Setting Mde Change Mde Change Fan Mde Select Prgram Mde Override/Permanent Override 9 Setting Schedule 20 Battery Lw Indicatin 23 Defrst Indicatin 23 Out f Temperature Range Indicatin 23 Advanced Recvery Indicatin 24 Filter Cunter 25 Shrt Cycle Start Up Prtectin 25 Energy Saving Mde 26 Z-Wave Setup and Operatins 26 Check FLiRS / Always Listening mde in ZTS-0 28 Z-Wave Add (Include) / Delete (Exclude) Mde Supprt fr Assciatin Grups 30 Z-Wave Cnfiguratin Parameters 32 Reset ZTS-0 t Factry Default Settings 35 Frequently Asked Questins 36 Technical Specificatins 37 Checking Accessries 38 FCC Ntice 39 Warnings 39 Cautin Intrductin ZTS-0 Z-Thermstat ZTS-0 Z-Thermstat (Figure ) is a Z-Wave enabled prgrammable thermstat that allws yu t cntrl yur rm temperature with prgrammable time schedule such as, AWAY, HOME and SLEEP event which can maximize energy cnservatin and cmfrt while minimizing the effrt required t maintaining the apprpriate temperature in yur hme whether yu are at hme r away. Als, yu can use the ZTS-0 t cntrl / check yur rm temperature by smart phne r PC while yu are at hme r utside thrugh Z-Wave gateway. Figure. ZTS-0 PROG ON FAN ON 2

3 Features List HVAC System Type Cmpatible: - Standard (gas/electric) r Heat Pump Multistage System Cmpatible: - Standard HVAC Systems: 2 stage heating, stage cling - Heat Pump Systems: 2 stage heating, stage cling Heat Pump change ver valve: - Selectable change ver with cl r with heat Prgram Style: - 2 prgram mdes fr scheduling (M-Fr, Sa-Su) - 4 Separate Time and Temperature Settings fr each prgram - Heat and Cl set-pints fr each prgram - Temprary Prgram Override - Permanent Prgram Override - Built-in flash memry stres heat and cl prgram settings Temperature Display and Cntrl: - Temperature display in F r C - Temperature Measurable Range: F / 0-40 C - Temperature Setting Range: 4-99 F / 5-37 C - Adjustable Temperature Cntrl Swing/Differential a) Swing: F, 2 F, 3 F r 4 F ( 0.5 C,.0 C,.5 C r 2 C) b) Differential: F, 2 F, 3 F r 4 F ( 0.5 C,.0 C,.5 C r 2 C) - Advanced Recvery Mde (ARM) - Defrst Functin - Shrt cycle start up prtectin Clck: - Time display frmat: 2/24 hur clck selectin with day displayed Filter Cunter: - Filter change reminder displayed after 500 hurs usage ( hrs) Z-Wave: - Supprt Netwrk Wide Inclusin (NWI) and Explre Frames - Supprt Easy mde (disable lcal advanced setup and cntrl) - Supprt "Frequently Listening Ruting Slaves" (FLiRS) mde and "Always Listening" mde - Supprt battery level reprt - Supprt Assciatin Grups a)assciatin Grup_ is used fr Heat Pump cntrl b)assciatin Grup_2 is used fr Cmpressr cntrl c)assciatin Grup_3 is used t reprt status change such as AUTO reprt t gateway Pwer: - Supprt AA x 4 alkaline batteries r 24Vac input Glssary Device r Nde Inclusin Exclusin Remve Netwrk Wide Inclusin (NWI) Z-Wave Netwrk Primary Cntrller FLiRS Mde Always Listening Mde Assciatin Devices and ndes are all terms t describe an individual Z-Wave device. These are all interchangeable when setting up yur Z-Wave netwrk. Add a Z-Wave device t the netwrk. Delete a Z-Wave device frm the netwrk. T take a device ut f a grup, scene r assciatin grup while that device still exists in the same Z-Wave netwrk. Netwrk Wide Inclusin (NWI) enables bth end-user friendly, Plug and Play like Z-Wave netwrk installatin as well as prfessinal installatin scenari where the inclusin prcess in terms f time will be reduced significantly. NWI is a feature supprted by a new frame type named Explrer which enables the Z-Wave prtcl t implement Adaptive Surce Ruting. A cllectin f Z-Wave devices is cntrlled by primary and secndary cntrllers perating n the same system. A Z-Wave netwrk has its wn unique ID cde s that cntrllers nt in the netwrk cannt cntrl the system. The first cntrller is used t set up yur devices and netwrk. Only the Primary Cntrller can be used t include r delete devices frm a netwrk. It is recmmended that yu mark the primary cntrller fr each netwrk fr ease in mdifying yur netwrk. FLiRS is abbreviatin fr "Frequently Listening Ruting Slave". FLiRS mde is targeted fr battery perated applicatins and will enter sleep mde frequently in rder t cnserve battery cnsumptin. The respnse t Z-Wave cmmand is nt as quick as Always Listening Device. Nrmally there is -2 secnds latency. Always Listening mde is targeted fr AC pwer perated applicatins and it can act as a repeater, which will re-transmit the RF signal t ensure that the signal is received by its intended destinatin by ruting the signal arund bstacle and radi dead spts. The respnse t Z-Wave cmmand is immediate. Assciatin is used trganize ndes in different grups allwing the device t identify the ndes by a grup identifier. The grups can als be cpied tther devices. 3 4

4 Physical Installatin and Wiring CAUTION - We highly recmmend that this installatin prcedure is perfrmed by a trained HVAC technician. - Read the enclsed instructins carefully befre installing yur new Z- Thermstat. Pay clse attentin t all warnings and ntes and carefully fllw the installatin steps in the rder they are presented t save time and minimize the risk f damaging the thermstat r the system it cntrls. - Turn ff ZTS-0 and the electrnic devices (e.g. heater, cler) which will be cnnected and the electric surce befre installatin and maintenance. Battery safety! - Use new batteries f the recmmended type and size nly. - Never mix used and new batteries tgether. - T avid chemical leaks, remve batteries frm the ZTS-0 if yu d nt intend t use the unit fr an extended perid f time. - Dispse f used batteries prperly; d nt burn r bury them. Read fllwing scenaris carefully befre yu start as it matters t the battery life under Z-Wave peratin: ZTS-0 can be pwered by 4 x AA batteries, and/r 24Vac C wire. a) If it is pwered by batteries r pwered by batteries first then applied with 24Vac befre Z-Wave inclusin, ZTS-0 will self-cnfigure t FLiRS mde which will save battery life by sleeping. b) If it is pwered by 24Vac r pwered by 24Vac first then applied with batteries befre Z-Wave inclusin, ZTS-0 will self-cnfigure t Always Listening Mde which will nt sleep. c) After inclusin prcess, ZTS-0 will nt detect pwer surce and nt allw changing peratin mde. Yu must perfrm exclusin prcess first if need t change Z-Wave peratin mde. d) After Z-Wave inclusin prcess, if yu reset ZTS-0 t default while bth 24Vac and batteries are applied, ZTS-0 will take 24Vac as primary pwer surce and self-cnfigure t Always Listening Mde, because reset t default prcess will autmatically exclude ZTS-0 frm the Z-Wave netwrk. Yu shuld discnnect the pwer surce and re-apply the pwer s ZTS-0 can detect the pwer surce type and self-cnfigure t crrespnding mde. Yu may check Glssary fr the definitin f FLiRS mde and Always Listening Mde. Installatin Lcatin The Thermstat is restricted t be used in indr nly. It shuld be munted n an inner wall abut.5m (5ft) abve the flr at a psitin where it is readily affected by changes f the general rm temperature with freely circulating air. Avid munting abve r near ht surfaces r equipment (e.g. TV, heater, refrigeratr). Avid munting where it will be expsed t direct sunshine, drafts, r in a laundry rm r ther enclsed space. D nt expse this unit t dripping r splashing liquids. Physically Installing the Thermstat. Open the ZTS-0 by pulling the tw sectins apart (Figure 2). Use the fingertips f ne hand t grip the tab n the frnt husing. 2. Apply pwer t the thermstat: a) Fr battery pwer, install fur AA batteries (alkaline recmmended). Match the plarity f the batteries with the +/- marks inside the battery cmpartment. b) Fr 24Vac pwer, cnnect the wires as described in "Wiring" 3. Insert the tw included wall anchrs int the wall, aligned with twf the munting hles in the back husing f the thermstat. 4. Fasten the back husing t the wall using the tw included munting screws. Insert the screws thrugh the munting hles in the husing and int the wall anchrs. (Figure 3) 5. Align the frnt husing f the thermstat with the back husing and push until the husing sectins are lcked tgether. Figure 2. Open ZTS Figure 3. Install the frnt husing

5 Wiring - Be sure the peratin mde is OFF and Fan selectin is Fan Aut - Wire the prper cables at the terminal blck accrding t the circuit diagram - Afterward, push all cables back int the wall - D nt use metal cnduit r f cable prvided with a metal sheath - Recmmends adding fuse r prtective device in the line circuit Terminals Cl changever (heat pump) Heat changever (heat pump) 2nd Stage heater st Stage heater Fan Cmpressr 24Vac Pwer fr Cling 24Vac Pwer fr Heating Symbl O B W2 W G Y RC RH C 24Vac Cmmn Imprtant! If yu will be pwering the ZTS-0 with 24Vac: Cnnect the "24Vac Cmmn" (typically the black wire/terminal) and "24Vac Pwer" (typically the Red wire/terminal) frm the HVAC system t the ZTS-0 HVAC System terminal blck "C" and "RH" r "RC" terminals (see the fllwing explanatin, these may be jumpered tgether). Cmmn r Split Transfrmer Systems: Mst HVAC systems have a cmmn heating and cling transfrmer. Yu must insert a jumper wire t tie the RH and RC inputs tgether fr this cnfiguratin. If yu have a system with separate heating and cling transfrmers, d nt insert a jumper wire between RC and RH. When wiring split systems, wire the heating systems "24Vac Pwer" (red wire) t the ZTS-0 "RH" terminal, and wire the cling systems "24Vac Pwer" t the ZTS-0 "RC" terminal. Als wire the cling systems "24Vac Cmmn" t the ZTS-0 "C" terminals. Figure 5. Heat pump HVAC system wiring O B W2 W G Y RC RH C Figure 6. Nn-heat pump 2-wires system wiring O B W2 W G Y RC RH C Orange Blue Brwn Green Yellw Red Black White Red Thermstat shuld be pwered by batteries and supprt heating cntrl nly. Figure 7.Heat pump 2-wires system wiring Heat Pump HVAC System O - Cl changever (heat pump) B - Heat changever (heat pump) nd W2-2 stage heater G - Fan Y - Cmpressr R - 24Vac Pwer C - 24Vac Cmmn st W - stage heater R - 24Vac Pwer HG HE J J2 J2 ELECTH HPUMP ELECTH HPUMP Nte: D nt split RC/RH fr Heat Pump systems! Figure 4. Nn-heat pump (Standard Gas r Electric) HVAC system wiring O B W2 W G Y RC RH C Brwn White Green Yellw Red Black Standard HVAC System nd W2-2 stage heater st W - stage heater G - Fan Y - Cmpressr R - 24Vac Pwer C - 24Vac Cmmn J2 ELECTH HPUMP O B W2 W G Y RC RH C Yellw Red Y - Cmpressr R - 24Vac Pwer Thermstat shuld be pwered by batteries and supprt heating cntrl nly. Fr heat pump utput, there is a 3 minutes ff time fr heat pump prtectin. HG HE J J2 ELECTH HPUMP 7 8

6 Jumper Settings fr ELECTH-HPUMP and HE-HG There are 6 jumpered pins n the thermstat circuit bard that identify whether yur system is: - Gas r electric heater - Nn-heat pump r heat pump system Yu must ensure that these pins are set crrectly fr yur system. The pin lcatin is shwn in the fllwing diagram which is lcated at back side f ZTS-0. Setup and Operatins Prduct Overview Figure 8. ZTS-0 Day Event mde Inclusin indicatin Battery lw indicatin Jumper ELECTH HPUMP Functin Descriptin Set t ELECTH fr nn-heat pump system (Default) - When there is a heating request, thermstat will turn n W - When there is a cling request, thermstat will turn n Y Time PROG ON FAN ON ELECTH HPUMP Set t HPUMP fr heat pump system - When there is a heating request, thermstat will turn n Y and B - When there is a cling request, thermstat will turn n Y and O HG HE HG HE Set t HG fr Gas heat-fan cntrlled unit (Default) Fan will maintain ff state. Set t HE fr Electrical heat-fan cntrlled unit Fan will be turned n when there is heating utput. Nte: The HE and HG jumper cntrls the Fan when set t Aut in heating mde. If user selects Fan ON at thermstat, the Fan will be turned n withut cnsidering the HE-HG jumper selectin. Prgram mde Fan mde Current temperature Descriptin f Functin Keys Symbl Key Descriptin Increase value / Tggle selectin Decrease value / Tggle selectin Mde Select fan mde; als the Backward functin key in sme menus Change peratin mde; als the Frward functin key in sme menus Select prgram mde: PROG ON, OVERRIDE and PERMANENT OVERRIDE; als the Cnfirm functin key in sme menus Back t Hme 9 0

7 Activate/Deactivate Easy Mde The ZTS-0 is default with Easy mde, belw illustrates the functins f Easy mde: - Active functins: Change Mde, change Fan mde and Temperature Scale selectin - Inactive functins: Scheduling, Prgram Mde, Clck Display, Setting Time, Setting Swing, Setting, Differential Set-Pint and Advanced Recvery Mde User can use Easy mde t disable Schedule functin and the schedule will be cntrlled by Z-Wave gateway. User can still change temperature and mde by pressing the lcal physical buttns. User can deactivate the Easy mde by lcal "Setting Mde" r Z-Wave Cnfiguratin Parameter number 8. (Please refer t Z-Wave Cnfiguratin parameters table). Belw is the example by lcal setting: Prcedure / Descriptin Press and hld "Mde" key fr 2 secnds t entry the setting mde. It will display "EASY YES" if it stays in Easy mde. Otherwise, it will display "EASY n" if Easy mde is deactivated. Press Up/Dwn key t tggle the selectin. Press "Prg" key t cnfirm yur settings. - it will g back t Hme page if selected "YES". - it will g t Day setting if selected "n". LCD indicatin Nte: If yu deactivated the Easy mde, please refer t Setting Mde fr the temperature scale selectin. Setting Mde (Set Day, Clck, 2/24 hur, F/C, Swing and Differential) Symbl Setting Mde Key Descriptin Increase value / Tggle selectin Decrease value / Tggle selectin Backward t previus setting Frward t next setting Cnfirm and g t next setting Cnfirm and g back t Hme Temperature Scale selectin in Easy Mde Prcedure / Descriptin LCD indicatin Press and hld "Prg" keys fr 2 secnds t entry temperature F (Fahrenheit) -> C (Celsius) selectin mde Press Up/Dwn key t tggle the temperature F (Fahrenheit) -> C (Celsius) selectin. Press "Prg" key t cnfirm it and back t the Hme page. 2

8 If yu deactivated the Easy mde, yu can cntinue t set up Day, Clck, 2/24 hur, F/C, Swing and Differential. Refer t belw fr steps: Prcedure / Descriptin Press and hld "Mde" key fr 2 secnds t entry the setting mde. LCD indicatin 4 Prcedure / Descriptin Press "Prg" key nce t cnfirm the setting and it will g t minutes setting. Minutes will keep flashing, press Up/Dwn key t set minutes. LCD indicatin It will display "EASY YES" if it stays in EASY mde. Otherwise, it will display "EASY n" if EASY mde is deactivated. Press Up/Dwn key t tggle the selectin. Press "Prg" key t cnfirm yur settings. - it will g back t Hme page if selected "YES". - it will g t Day setting if selected "n". 5 Press "Prg" key nce t cnfirm the setting and it will g t 2/24 hur clck selectin. Press Up/Dwn key t tggle the 2/24 hur clck selectin. PM HR EASY mde (default) Lcal cntrl active functins: - Change Mde - Change Fan mde - Temperature Scale selectin Lcal cntrl inactive functins: - Scheduling - Prgram Mde - Clck Display - Setting Time - Setting Swing - Setting Differential Set-Pint - Advanced Recvery Mde EASY mde is deactivated - Supprt full functins at lcal and Z-Wave cntrl 6 7 Press "Prg" key nce t cnfirm the setting and it will g t temperature F (Fahrenheit) -> C (Celsius) selectin. Press Up/Dwn key t tggle the temperature F (Fahrenheit) -> C (Celsius) selectin. Press "Prg" key nce t cnfirm the setting and it will g t swing setting. Press Up/Dwn key t set the swing setting. (Range is frm 0.5 C t 2 C r F t 4 F ) SWING 2 3 Day will keep flashing, press Up/Dwn key t set day frm -SU. Press "Prg" key nce t cnfirm the setting and it will g t hur setting. Hur will keep flashing, press Up/Dwn key t set hur. 8 Press "Prg" key nce t cnfirm the setting and it will g t differential set pint setting. Press Up/Dwn key t set the differential set pint setting. (Range is frm 0.5 C t 2 C r F t 4 F ) DIFF 3 4

9 9 Prcedure / Descriptin Press "Prg" key nce t cnfirm the setting and it will g t Advanced Recvery setting. Press Up/Dwn key t enable/disable Advanced Recvery Mde. RECOVERY LCD indicatin COOL Mde: thermstat cntrls the temperature accrding t the fllwing diagram Output Set pint Cl 0 Press "Prg" key nce t cnfirm the setting and it will g t the Hme page. RECOVERY PROG ON OFF Off Turn ff Swing Turn n Example fr Cling: (Set pint = 80 F, Swing = F) => Cler turns n when rm temp is 8 F and ff at 79 F. Temperature Nte: Explanatins f Swing and Differential set pint mde: thermstat cntrls the temperature accrding t the fllwing diagram AUTO: Output thermstat cntrls the temperature accrding t the fllwing diagram Heat Set pint Cl Set pint Output Set pint nd 2 Turn n nd 2 Turn ff Off nd 2 Turn n st Turn n Diff Swing nd 2 Turn ff Swing st Turn ff Temperature SD= switch differential Example fr Heating: (Set pint = 70 F, Swing = F, Differential = 2 F) => st stage heater turns n when rm temp is 69 F and ff at 7 F. => 2nd stage heater turns n when rm temp is 67 F and ff at 70 F. Heat Off st Turn n st Turn ff There is a dead band 4 F/2 C between heat set pint and cl set pint. Example : If user select heat set pint is 70 F, the minimum cl set pint will be limited at "heat set pint" + 4 F: 74 F Pervius heat set pint is 70 F and cl set pint is 74 F Temperature Example 2: If user changes heat set pint t 72 F, cl set pint will be updated t 76 F autmatically t maintain the dead band. Heat Diff Swing Dead band Swing 5 6

10 Change Mde Nte: In Heat mde Belw example is based n PUMP =>it displays "" if ELECTH is selected during jumper setting. => it displays " PUMP" if HPUMP is selected during jumper setting. Prcedure / Descriptin LCD indicatin Change Fan Mde Prcedure / Descriptin Press "Fan" key nce t change the Fan mde: -> FAN ON : Electric heat (HE): Fan runs nly when Heating/Cling is running. LCD indicatin COOL OFF Gas heat (HG): Fan runs nly when Cling is running. 2 Press "Fan" key nce t change the Fan mde: -> FAN ON Press "Mde" key nce t change the peratin mde: OFF -> (PUMP) -> COOL -> AUTO -> OFF FAN ON: Fan stays n all the time. Select Prgram Mde FAN ON COOL Prcedure / Descriptin LCD indicatin COOL Press "Prg" key nce t select PROG mde: PROG ON -> OVERRIDE -> PERMANENT OVERRIDE PROG ON: Run the schedule. PROG ON COOL AUTO 2 Press "Prg" key nce t select PROG mde: OVERRIDE: Temprary verride the current schedule and will g back t "PROG ON" when next time schedule reach. OVERRIDE 3 Press "Prg" key nce t select PROG mde: PERMANENT OVERRIDE: Permanent verride the schedule until user change back t "PROG ON". PERMANENT OVERRIDE 7 8

11 Override/Permanent Override Nte: Override/Permanent Override is nly available in, COOL r AUTO mde Prcedure / Descriptin Press "Prg" key nce t select PROG mde: OVERRIDE r PERMANENT OVERRIDE at Hme page. Press Up/Dwn key t adjust set pint temperature in r COOL mde. Press "Prg" key nce t cnfirm the setting. In AUTO mde, user needs t set heat and cl set pints temperature. Press Up/Dwn key t adjust aut heat set pints temperature in AUTO mde. Press "Prg" key nce t cnfirm the setting. Press Up/Dwn key t adjust aut cl set pint temperature in AUTO COOL mde. Press "Prg" key nce t cnfirm the setting and g back t Hme page. OVERRIDE OVERRIDE OVERRIDE OVERRIDE OVERRIDE LCD indicatin TARGET TARGET TARGET TARGET TARGET r COOL AUTO COOL AUTO Setting Schedule Belw are the recmmended settings fr different schedule scenaris: ZTS-0 Schedule scenaris Easy mde setting ZTS-0 schedule Remark Gateway cntrller des have an independent thermstat schedules. Gateway cntrller des NOT have an independent thermstat schedules. Enable Easy mde (Refer t "Activate/ Deactivate Easy Mde" sectin) Disable Easy mde (Refer t "Activate/ Deactivate Easy Mde" sectin) Pre-defined Schedule (disabled by default): I FR SA I SU Event AWAY HOME SLEEP AWAY HOME SLEEP Time 6:00 8:00 6:00PM 0:00PM 6:00 0:00 6:00PM :00PM Schedule functin will be disabled. Schedule functin will be enabled. (Refer t "Predefined Schedule" fr the default settings.) User can adjust it accrding t persnal preference. Heat 70 F (2 C) 62 F (7 C) 70 F (2 C) 62 F (7 C) 70 F (2 C) 62 F (7 C) 70 F (2 C) 62 F (7 C) Schedule functin will be cntrlled by gateway. (User shuld setup the schedule functin in gateway) Schedule functin will be cntrlled by ZTS-0. Cl 78 F (26 C) 85 F (29 C) 78 F (26 C) 82 F (28 C) 78 F (26 C) 85 F (29 C) 78 F (26 C) 82 F (28 C) 9 20

12 Prcedure / Descriptin LCD indicatin Prcedure / Descriptin LCD indicatin Press and hld "Prg" key fr 2 secnds t entry the setting schedule mde. Press Up/Dwn key t select -FR r SA-SU schedule. TU WE TH FR SA SU 5 Press and hld "UP" and "DOWN" key fr 2 secnds t disable / enable event during the time setting. If the event is disabled, "OFF" will be displayed. If the event is enabled, time will be displayed and Hur will keep flashing. TU WE TH FR TU WE TH FR TU WE TH FR Press "Prg" key nce t cnfirm the setting and it will g t target setting. TU WE TH FR AWAY 6 If the event is enabled, it will g t target setting. Target will keep flashing, press Up/Dwn key t adjust Heat set pint fr heating. TU WE TH FR TARGET 2 Press "Prg" key nce t cnfirm the setting and it will g t event mde. Press Up/Dwn key t select the event ( -> AWAY -> HOME -> SLEEP). TU WE TH FR HOME 7 If the event is disabled, it will g t next event setting. Press "Prg" key nce t cnfirm the setting and it will g t target setting. Target will keep flashing, press Up/Dwn key t adjust Cl set pint fr cling. TU WE TH FR TARGET COOL TU WE TH FR SLEEP 8 Press "Prg" key nce t cnfirm the setting and it will g t next event mde. Fllw the prgram UI t cmplete the whle scheduling r press Hme key nce t save and exit. 3 Press "Prg" key nce t cnfirm the setting and it will g t hur setting. Hur will keep flashing, press Up/Dwn key t set hur. TU WE TH FR 4 Press "Prg" key nce t cnfirm the setting and it will g t minutes setting. Minutes will keep flashing, press Up/Dwn key t set minutes. TU WE TH FR 2 22

13 Battery Lw Indicatin Advanced Recvery Indicatin Prcedure / Descriptin ZTS-0 thermstat will detect the battery level every 30 minutes; Battery lw icn will be displayed at Hme page if the battery is running ut. (User is required t change new batteries.) Defrst Indicatin Prcedure / Descriptin DEFROST icn will be displayed at Hme page if temperature belw 4 F/5 C. All heaters will be frced On, except in cl mde. PROG ON TU LCD indicatin LCD indicatin PUMP DEFROST 2 PUMP Prcedure / Descriptin The Advanced Recvery feature allws heating and cling systems t gradually recver frm an energy-saving set pint temperature t a cmfrt set pint temperature. Advanced Recvery calculates the time needed t adjust the temperature t the next prgram setting. When the thermstat is in Advanced Recvery mde, the display will shw "RECOVERY". Advanced Recvery is an ptin that allws the HVAC system t attempt t recver frm a setback perid and reach a desired cmfrt temperature set pint by the beginning f yur prgrammed cmfrt perid. This ptin allws the chice whether t use Advanced Recvery under Setting Mde. RECOVERY LCD indicatin Out f Temperature Range Indicatin (Recvery wrks in heat, cl and aut mde. Maximum Advanced Recvery time is ne hur.) 2 Prcedure / Descriptin HI icn will be displayed n LCD if temperature excess the measurement ranges 99 F/40 C. All heaters will be frced Off. Cler will turn n if running cl mde. LO icn will be displayed n LCD if temperature belw the measurement ranges 32 F/0 C. All heaters will be frced On, except in cl mde. TU TU LCD indicatin COOL DEFROST 2 PUMP 23 24

14 Filter Cunter Prcedure / Descriptin LCD indicatin Energy Saving Mde User can enable/disable energy saving mde by using Z-Wave BASIC set cmmand nly. (yu may refer t the Z-Wave primary cntrller UI fr it) Press and hld "Fan" key fr 2 secnds t check the filter cunter. The "usage hurs" will be shwn n screen. HR FILTER => Enable energy saving mde Basic set value = 0x00 (ff) (energy saving mde will be mapped tff mde) 2 Press and hld "Prg" key fr 2 secnds t reset the filter cunter after replace a new filter. HR FILTER => Disable energy saving mde Basic set value = 0xFF (Resume) (cmfrt mde will mapped t resume mde) 3 4 Press and hld "Mde" key t set the alert time fr the filter usage. "Target" icn will be shwn n screen and flashing. Press "UP" r "Dwn" t set the alert time. (Range frm 500 t 4000 Hurs size is 00hrs) Press "Prg" key t cnfirm the setting and g back t filter cunter page. Press "Hme" key nce t g back t the Hme page. FILTER icn will be shwn n the screen at Hme page when the usage hurs were reached t set time. PROG ON Shrt Cycle Start Up Prtectin T prtect the cmpressr / Heat pump, thse utputs frced ff until 3minutes cunt dwn finished. Thse utputs can be activated accrding t the rm temperature after 3 minutes. HR FILTER TARGET FILTER COOL Z-Wave Setup and Operatins Setting FLiRS r Always Listening mde - Setting t Z-Wave FLiRS mde with batteries as pwer surce ZTS-0 will self-cnfigure t FLiRS mde if it is pwered by batteries r pwered by batteries first then applied with 24Vac befre Z-Wave inclusin. FLiRS mde is targeted fr battery perated applicatins and will enter sleep mde frequently in rder t save battery life. ZTS-0 can't act as a repeater in this mde. The respnse t Z-Wave cmmand is nt as quick as Always Listening Device. Nrmally there is -2 secnds latency n respnse, yu shuld avid sending cmmands t ZTS-0 t frequently. - Setting t Z-Wave Always Listening mde with 24Vac as pwer surce ZTS-0 will self-cnfigure t Always Listening Mde if it is pwered by 24Vac r pwered by 24Vac first then applied with batteries befre Z-Wave inclusin. Always Listening mde is targeted fr AC pwer perated applicatins and it can act as a repeater which will re-transmit the RF signal t ensure that the signal is received by its intended destinatin by ruting the signal arund bstacle and radi dead spts. The respnse t Z-Wave cmmand is immediate. System Nn Heat pump system Heat pump system Output Cmpressr st stage heat and cmpressr 25 26

15 Imprtant: Please nte the belw scenaris fr pwer applying because it will affect the battery life if the steps are nt crrect (this is als mentined at Physical Installatin and Wiring sectin in this user manual): a) If it is pwered by batteries r pwered by batteries first then applied with 24Vac befre Z-Wave inclusin, ZTS-0 will self-cnfigure t FLiRS mde which will save battery life by sleeping. b) If it is pwered by 24Vac r pwered by 24Vac first then applied with batteries befre Z-Wave inclusin, ZTS-0 will self-cnfigure t Always Listening Mde which will nt sleep. c) After inclusin prcess, ZTS-0 will nt detect pwer surce and nt allw changing peratin mde. Yu must perfrm exclusin prcess first if need t change Z-Wave peratin mde. d) After Z-Wave inclusin prcess, if yu reset ZTS-0 t default while bth 24Vac and batteries are applied, ZTS-0 will take 24Vac as primary pwer surce and self-cnfigure t Always Listening Mde, because reset t default prcess will autmatically exclude ZTS-0 frm the Z-Wave netwrk. Yu shuld discnnect the pwer surce and re-apply the pwer s ZTS-0 can detect the pwer surce type and self-cnfigure t crrespnding mde. Remark: - If yu are using battery and smehw it is in Z-Wave Always Listening Mde, r if yu are using battery as back up, and the AC pwer is dwn, the battery will drain very fast (battery will nly survive 3-5 days). - Regardless the FLiRS mde r Always Listening Mde, the setup and peratins are same, and yu can als use lcal cntrl while is it included t Z- Wave netwrk. Check FLiRS / Always Listening mde in ZTS-0 Prcedure / Descriptin During nrmal peratin, press and keep hlding the keys n "Fan" + "Mde" + "Prg" fr 3 secnds. (The unit will resume t nrmal peratin after released all keys.) - If the LCD displays "bt", the unit is detected t be FLiRS mde if it will be included int Z-Wave netwrk; - If the LCD displays "AC", the unit is detected t be Always Listening mde if it will be included int Z-Wave netwrk; - If the LCD displays "bt" + "RF icn", the unit is in FLiRS mde and is included int Z-Wave netwrk; - If the LCD displays "AC" + "RF icn", the unit is in Always Listening mde and is included int Z-Wave netwrk. LCD indicatin Nte: After Z-Wave inclusin prcess, if yu reset ZTS-0 t default while bth 24Vac and batteries are applied, ZTS-0 will take 24Vac as primary pwer surce and self-cnfigure t Always Listening Mde. If yu are using battery as back up, and the AC pwer is dwn, the battery will drain very fast, battery will nly survive 3-5 days. Z-Wave Add (Include) / Delete (Exclude) int/frm Z-Wave netwrk Add (Include) ZTS-0 t Gateway / Cntrller Z-Wave netwrk Symbl Inclusin and Exclusin Mde Key Descriptin Add (Include) / Delete (Exclude) 27 28

16 2 Prcedure / Descriptin Gateway / Cntrller device shuld be set t inclusin mde. Press and hld "Hme" key fr 2 secnds t set ZTS-0 t Add (Inclusin) / Delete (Exclusin) Mde. Press "Prg" key nce, it will search the netwrk. LCD indicatin Delete (Exclude) ZTS-0 frm Gateway / Cntrller Z-Wave netwrk Prcedure / Descriptin Gateway / Cntrller device shuld be set t Exclusin mde. Press and hld "Hme" key fr 2 secnds t set ZTS-0 t Add (Inclusin) / Delete (Exclusin) Mde. LCD indicatin 3 4 If the ZTS-0 is added int the netwrk successfully, the signal f "dne" will appear. Press "Hme" key nce t g back t the hme page. will appear n the main display. PROG ON Nte: - It is recmmended t perfrm the Delete/Exclude prcedure befre ding Add/Include. This is t make sure the ZTS-0 is nt in any ther Z-Wave netwrk which will result in failure in Inclusin prcess. - If the inclusin is failed, try exclusin, and/r reset ZTS-0 t factry default and try inclusin again. - After ZTS-0 is included t Z-Wave netwrk, it will stay in Easy mde by default. - Yu can enable r disable Easy mde by lcal "Setting Mde" r Z-Wave parameter number 8. (please refer t parameter table at Z-Wave Cnfiguratin Parameters). COOL Press "Prg" key nce, it will search the netwrk. If the ZTS-0 is remved frm the netwrk, it shws n cnnectin. Exclusin is cmpleted. Press "Hme" key nce t g back t the hme page. will appear n the main display. Supprt Assciatin Grups (Assciatin Cmmand Class) ZTS-0 supprts 3 assciatin grups. Mde Heating mde Cling mde OFF Assciatin grup PROG ON Assciatin grup_ (Heat pump) ON (basic set cmmand 0xFF) OFF (basic set cmmand 0x00) OFF (basic set cmmand 0x00) Assciatin grup_2 (Cmpressr) OFF OFF (basic set cmmand 0x00) ON (basic set cmmand 0xFF) OFF (basic set cmmand 0x00) 29 30

17 Assciatin grup_3: (Aut reprt) - Assciatin grup_3 is used t reprt status change t gateway. (Only gateway r cntrller can be assigned in this assciatin grup) ZTS-0 will trigger AUTO reprt functin if ne f belw status is changed. I. Operatin mde (Off, Heat, Cl, Aut) II. Operatin state (Heat n r ff, Cl n r ff) III. Fan mde (Aut, Aut lw) IV. Fan state (Fan n r Fan ff) V. Heat set pint (reprt in precisin after decimal, e.g. 2. C ) VI. Cl set pint (reprt in precisin after decimal, e.g C ) VII. Current rm temperature (reprt in precisin after decimal, e.g C) (It will trigger rm temperature reprt if there is 4 F r 2 C (default) differ frm last reprt. Yu can change this setting by set the cnfiguratin parameter) Nte: Ttal 5 devices (ndes) can be assigned in ttal 3 assciatin grups. Belw table lists ut the devices (ndes) allcatins in the 3 assciatin grups. Case N. N. f Nde ID in Assciatin grup_ Imprtant: Please d nt assciate heat pump and cmpressr devices in same assciatin grup because heat pump and cmpressr device cannt be turned n simultaneusly! Assciatin Grups setting example (case 3): N. f Nde ID in Assciatin grup_2 N. f Nde ID in Assciatin grup_3 Case 4 0 (AUTO reprt) Case 2 3 (AUTO reprt) Case (AUTO reprt) Case 4 3 (AUTO reprt) Case (AUTO reprt) F-BW804 (ZFM-80) (Nde ID-A) F-BW804 (ZFM-80) (Nde ID-C) F-BW804 (ZFM-80) (Nde ID-B) F-BW804 (ZFM-80) (Nde ID-D) Assciatin grup_ fr Heat Pump Assciatin grup_2 fr Cmpressr F-BW803 (ZTS-0) Assciatin grup_3 fr Aut reprt t gateway Z-Wave Gateway (Nde ID-E) Z-Wave Cnfiguratin Parameters Different user has different preferred settings f their thermstat, yu may use the belw cnfiguratin parameters t change settings f crrespnding functinality. Swing Functins Differential Set filter cunter Reprt filter cunter (read nly) Scale f temperature Upper limit f set pint (A) Lwer limit f set pint (B) Easy mde Time frmat Repeat basic set cunter (Assciatin Grup A and B nly) Parameter N. (0x0) 2 (0x02) 3 (0x03) 4 (0x04) 5 (0x05) 6 (0x06) 7 (0x07) 8 (0x08) 9 (0x09) 0 (0x0A) Parameter value range (0x0) = F / 0.5 C 2 (0x02) = 2 F /.0 C (default) 3 (0x03) = 3 F /.5 C 4 (0x04) = 4 F / 2.0 C (0x0) = F / 0.5 C 2 (0x02) = 2 F /.0 C (default) 3 (0x03) = 3 F /.5 C 4 (0x04) = 4 F / 2.0 C 500 (0x0F4) t 4000 (0x0FA0) hurs Default = 500 (0x0F4) hurs Reslutin = 00 (0x0064) hurs 0 (0x0000) t 9999 (0x270F) hurs 0 (0x00) = C (0x0) = F (default) (A) available range: Unit in Celsius ( C): A = (B+2)min. ~ (37.0 C) max. Unit in Fahrenheit ( F): A = (B+4)min. ~ (99.0 F) max. (default = 99.0 F) (B) available range: Unit in Celsius ( C): 5.0 C t 35.0 C Unit in Fahrenheit ( F): 4.0 F t 95.0 F (default = 4.0 F) 0 (0x00) = Disable (0x0) = Enable, default 0 (0x00) = 24 hurs (0x0) = 2 hurs (am / pm), default Value(X): 0 (0x00), 3 (0x03) t 255 (0xFF) 0 (0X00) = Disable, default 3 (0x03) t 255 (0xFF) minutes (Thermstat sends "Basic Set" cmmand t its assciatin nde repeatedly in every X minutes) 3 32

18 Functins Trigger AUTO reprt if rm temperature is different frm last reprt. (It will reprt rm temperature nly) *User can use this functin t enhance batteries service life. AUTO reprt by time interval. (It will reprt rm temperature nly) *User can use this functin t enhance batteries service life. Parameter N. (0x0B) 2 (0x0C) Parameter value range 0 (0x00) = disable AUTO reprt if rm temperature is different frm last reprt. AUTO reprt if rm temperature is different frm last reprt. Delta change is >= (0x0) = F (0.5 C) 2 (0x02) = 2 F (.0 C) 3 (0x03) = 3 F (.5 C) 4 (0x04) = 4 F (2.0 C), (default) 5 (0x05) = 5 F (2.5 C) 6 (0x06) = 6 F (3.0 C) 7 (0x07) = 7 F (3.5 C) 8 (0x08) = 8 F (4.0 C) 0 (0x00) = disable AUTO reprt functin. (by time interval) AUTO reprt timer: (0x0) = 0.5 hr 2 (0x02) =.0 hr, (default) 3 (0x03) =.5 hrs 4 (0x04) = 2.0 hrs 5 (0x05) = 2.5 hrs 6 (0x06) = 3.0 hrs 7 (0x07) = 3.5 hrs 8 (0x08) = 4.0 hrs 9 (0x09) = 4.5 hrs 0 (0x0A) = 5.0 hrs (0x0B) = 5.5 hrs 2 (0x0C) = 6.0 hrs 3 (0x0D) = 6.5 hrs 4 (0x0E) = 7.0 hrs 5 (0x0F) = 7.5 hrs 6 (0x0) = 8.0 hrs Functins Sensr temperature calibratin. (This parameter is used t change the display temperature t match with yur previus thermstat, r t match anther thermstat already in yur hme) Parameter N. Example fr sensr temperature calibratin: reading temperature (77 F) + (-2 F) Functins Sensr temperature calibratin 3 (0x0D) Parameter N. 3 (0x0D) Parameter value range Temperature ffset value. Frmula: Display temperature = sensr reading value + ffset value (unit = degree F) 0 (0x00) = 0 F (default) (0x0) = F (0.5 C) 2 (0x02) = 2 F (.0 C) 3 (0x03) = 3 F (.5 C) 4 (0x04) = 4 F (2.0 C) 5 (0x05) = 5 F (2.5 C) 6 (0x06) = 6 F (3.0 C) 7 (0x07) = 7 F (3.5 C) 8 (0x08) = 8 F (4.0 C) 9 (0x09) = 9 F (4.5 C) 0 (0x0A) = 0 F (5.0 C) - (0xFF) = - F (-0.5 C) -2 (0xFE) = -2 F (-.0 C) -3 (0xFD) = -3 F (-.5 C) -4 (0xFC) = -4 F (-2.0 C) -5 (0xFB) = -5 F (-2.5 C) -6 (0xFA) = -6 F (-3.0 C) -7 (0xF9) = -7 F (-3.5 C) -8 (0xF8) = -8 F (-4.0 C) -9 (0xF7) = -9 F (-4.5 C) -0 (0xF6) = -0 F (-5.0 C) Parameter value range -2 (0xFE) = -2 F (-.0 C) If using decimal input Parameter n. = 3 Parameter value = -2 If using hexadecimal input Parameter n. = 0D Parameter value = FE ( Size >= byte) Display temperature = sensr reading value + ffset value = 77-2 F = 75 F 33 34

19 Reset ZTS-0 t Factry Default Settings 2 Prcedure / Descriptin Press and hld "Fan" + "Mde" keys fr 2 secnds t entry the reset mde. Press Up/Dwn key t tggle Yes/N selectin. Press "Prg" key nce t cnfirm the actin. => It will perfrm the reset if select "Yes" r => It will back t hme page if select "N". LCD display dne after reset t factry default settings. The fllwing data will be reset t default:. Clck : 2:00am 2. Day: Mn 3. Temperature scale: F 4. Swing : 2F 5. Diff: 2F 6. Pre-defined schedule 7. Operatin mde: OFF 8. Default Heat verride set pint 9. Default Cl verride set pint 0.Filter cunter cleared.delete frm netwrk 2. All cnfiguratin parameters value LCD indicatin Frequently Asked Questins Q Why wn't my ZTS-0 wrk with the Z-Wave devices I purchased frm anther cuntry? A Due t different cuntries regulatins Z-Wave prducts frm different regins are set t different frequencies. Befre purchasing new devices make sure yu have checked t see that the device is cmpatible in yur regin. Q D I need an electrician t install ZTS-0 in my huse? A We recmmend that yu acquire the services f a qualified technician t install this prduct. Q Hw d I knw which prduct is cmpatible t my ZTS-0? A ZTS-0 shuld wrk with any Z-Wave cntrller r gateway that has cntrl capability fr "Thermstat" devices. All Z-Wave prducts als cme with the Z-Wave lg. Q Can I use 2 r mre ZTS-0 in my huse? What is the max. units if yes? A Yes and it is very depends n the capability f gateway / cntrller. Fr example, gateway can supprts up t 8, 6 r 32 ZTS-0 in a netwrk. Q What is the recmmended battery type fr ZTS-0 and what is estimated batteries service life? A We recmmend using alkaline batteries fr ZTS-0. Batteries service life is very depend n the number f usage per day. Nrmally, batteries service life is arund year while perated in FLiRS mde. If yu are using battery and smehw it is in Z-Wave Always Listening Mde, r if yu are using battery as back up, and the AC pwer is dwn, the battery will drain very fast, battery will nly survive 3-5 days

20 Technical Specificatins Mdel n. RF frequency RF perating distance Z-Wave assciatin grup LCD Pwered by Relay cntact Temperature measurable range Temperature display reslutin Temperature Setting range Temperature Dimensin (L x H x T) BW803US (ZTS-0US) BW803AU (ZTS-0AU) BW803EU (ZTS-0EU) 908.4MHz (US) (ZTS-0US) 92.4MHz (AU) (ZTS-0AU) 868.4MHz (EU) (ZTS-0EU) Up t 00ft utdr line f sight, in unbstructed envirnment Supprts 3 assciatin grups, max. 5 ndes ID can be assigned t these assciatin grups. TN type with white backlight VA=66.5mmx28.5mm Dry battery AA x 4pcs r 24 VAC +/- 20% 50/60Hz Vltage: 24 VAC 50/60 Hz Current: A Max. (inductive) F / 0-40 C 0.5 F / 0. C 4-99 F / 5-37 C Operating: F / 0-50 C Strage: F / C 45mm x 00mm x 25mm Z-Wave device type Basic Device Class: Ruting_Slave Generic Device Class: Thermstat Specific Device Class: Thermstat general v2 Z-Wave Cmmand Class Cntrlled Supprted COMMAND_CLASS_THERSTAT_FAN_DE NO YES COMMAND_CLASS_THERSTAT_FAN_STATE NO YES COMMAND_CLASS_THERSTAT_DE NO YES COMMAND_CLASS_THERSTAT_SETPOINT NO YES COMMAND_CLASS_THERSTAT_OPERATING_STATE NO YES COMMAND_CLASS_THERSTAT_SETBACK NO YES COMMAND_CLASS_SENSOR_MULTILEVEL NO YES COMMAND_CLASS_CLOCK NO YES COMMAND_CLASS_BATTERY NO YES COMMAND_CLASS_BASIC YES YES COMMAND_CLASS_VERSION NO YES COMMAND_CLASS_MANUFACTURER_SPECIFIC NO YES COMMAND_CLASS_ASSOCIATION NO YES Weight 70g (Batteries excluded) COMMAND_CLASS_CONFIGURATION NO YES Checking Accessries After pening the cver f the packaging bx, check that the fllwing accessries are included. - ZTS-0: Z-Thermstat - AA batteries x 4pcs (ptinal) - Screw + Wall Anchr x 4pcs - User Manual - RC/RH jumper wire x pc - Warranty sheet 37 38