FEATURES TYPICAL APPLICATIO. LTC1382 5V Low Power RS232 Transceiver with Shutdown DESCRIPTIO APPLICATIO S
|
|
- Abner Armstrong
- 5 years ago
- Views:
Transcription
1 FEATRES Operates from a Single V Supply Low Supply Current: I CC = µa I CC =.µa in Shutdown Mode ESD Protection Over ±1kV ses Small Capacitors:.1µF Operates to 1kBaud Output Overvoltage Does Not Force Current Back into Supplies RS3 I/O Lines Can Be Forced to ±V Without Damage Pin Compatible with LT11A APPLICATIO S Notebook Computers Palmtop Computers DESCRIPTIO LTC13 V Low Power RS3 Transceiver with Shutdown The LTC 13 is an ultra-low power -driver/-receiver RS3 transceiver that operates from a single V supply. The charge pump requires only four spacesaving.1µf capacitors. The transceiver operates in one of two modes, Normal and Shutdown. In the Normal mode, I CC is only µa with the driver outputs unloaded. In the Shutdown mode, the charge pump is turned off, the driver outputs are forced into three-state, both receivers are off and I CC drops to.µa. The LTC13 is fully compliant with all data rate and overvoltage RS3 specifications. The transceiver can operate up to 1kbaud with a pf, 3kΩ load. Both driver outputs and receiver inputs can be forced to ±V without damage and can survive multiple ±1kV ESD strikes., LTC and LT are registered trademarks of Linear Technology Corporation. TYPICAL APPLICATIO -Drivers/-Receivers with Shutdown 17 = V.1µF 3 LTC13 7.1µF.1µF.1µF 3k LOGIC INPT k LOGIC INPT 11 3 LOGIC 13 1 k 3 INPT QIESCENT CRRENT (µa) Quiescent and Shutdown Supply Current 3 1 TEST CONDITION: = V SHTDOWN CRRENT QIESCENT CRRENT SHTDOWN CRRENT (µa) LOGIC ON/OFF 1 1 k INPT TEMPERATRE ( C) LTC13 TA LTC13 TA1 1
2 LTC13 ABSOLTE AXI RATI GS W W W Supply Voltage ( )... V Input Voltage Driver....3V to +.3V Receiver... V to V Digital Input....3V to +.3V Output Voltage Driver... V to V Receiver....3V to +.3V Short-Circuit Duration V sec V... 3 sec Driver Output... Indefinite Receiver Output... Indefinite Operating Temperature Range LTC13C... C to 7 C LTC13I... C to C Storage Temperature Range... C to 1 C Lead Temperature (Soldering, 1 sec)... 3 C W PACKAGE/ORDER I FOR ATIO NC C1 + V + C1 C + C V TR OT RX IN N PACKAGE 1-LEAD PDIP TOP VIEW SW PACKAGE 1-LEAD PLASTIC SO T JMAX = 1 C, θ JA = C/W (N) T JMAX = 1 C, θ JA = C/W (S) 1 ON/OFF 17 1 GND 1 TR1 OT 1 RX1 IN 13 RX1 OT 1 TR1 IN 11 TR IN 1 RX OT ORDER PART NMBER LTC13CN LTC13CSW LTC13IN LTC13ISW Consult LTC Marketing for parts specified with wider operating temperature ranges. DC ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range. = V, C1 = C = C3 = C =.1µF, V ON/OFF =, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX NITS Any Driver Output Voltage Swing 3k to GND Positive. 7. V Negative.. V Logic Input Voltage Level Input Low Level (V OT = High) 1.. V Input High Level (V OT = Low). 1. V Logic Input Current V IN = µa V IN = V µa Output Short-Circuit Current V OT = V ±9 ±1 ma Output Leakage Current Shutdown or = V (Note 3), V OT = ±1V ±1 ± µa Any Receiver Input Voltage Thresholds Input Low Threshold. 1.3 V Input High Threshold 1.7. V Hysteresis.1. 1 V Input Resistance 1V V IN 1V 3 7 kω Output Voltage Output Low, I OT = 1.mA ( = V).. V Output High, I OT = 1µA ( = V) V Output Short-Circuit Current Sinking Current, V OT = 1 ma Sourcing Current V OT = V 1 ma Output Leakage Current Shutdown (Note 3), V V OT 1 1 µa
3 DC ELECTRICAL CHARACTERISTICS LTC13 The denotes specifications which apply over the full operating temperature range. = V, C1 = C = C3 = C =.1µF, V ON/OFF =, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX NITS Power Supply Generator V + Output Voltage I OT = ma. V I OT = ma 7. V V Output Voltage I OT = ma. V I OT = ma 7. V Supply Rise Time Shutdown to Turn-On. ms Power Supply Supply Current No Load (Note ), C to 7 C.. ma No Load (Note ), C to C.3 1. ma Supply Leakage Current ( ) Shutdown (Note 3). 1 µa Digital Input Threshold Low 1.. V Digital Input Threshold High. 1. V AC CHARACTERISTICS The denotes specifications which apply over the full operating temperature range. = V, C1 = C = C3 = C =.1µF, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX NITS Slew Rate, C L = 1pF 3 V/µs, C L = pf 3 V/µs Driver Propagation Delay t HLD (Figure 1) 3. µs (TTL to RS3) t LHD (Figure 1) 3. µs Receiver Propagation Delay t HLR (Figure ).3. µs (RS3 to TTL) t LHR (Figure ).3. µs Note 1: Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note : Supply current is measured with driver and receiver outputs unloaded. Note 3: Measurements made in the Shutdown mode are performed with V ON/OFF = V. VOLTAGE (V) TYPICAL PERFOR A CE CHARACTERISTICS 1 Driver Output Voltage HIGH = V =.V LOW =.V = V W TEMPERATRE ( C) THRESHOLD VOLTAGE (V) Receiver Input Thresholds V TH V TL TEMPERATRE ( C) SPPLY CRRENT (ma) Supply Current vs Data Rate = V C L = pf S ACTIVE DATA RATE (kbad) LTC13 TPC1 LTC13 TPC LTC13 TPC3 3
4 LTC13 TYPICAL PERFOR A CE CHARACTERISTICS W 1 Supply Current 1 Driver Short-Circuit Current Receiver Short-Circuit Current SPPLY CRRENT (ma) S LOADED 1 LOADED SHORT-CIRCIT CRRENT (ma) I SC I SC + SHORT-CIRCIT CRRENT (ma) 3 I SC + I SC TEMPERATRE ( C) TEMPERATRE ( C) TEMPERATRE ( C) LTC13 TPC LTC13 TPC LTC13 TPC Driver Leakage in Shutdown Driver Output Waveforms Receiver Output Waveforms LEAKAGE CRRENT (µa) V OT = V V OT = V C L = pf INPT LTC13 TPC RECEIVER C L = 1pF INPT LTC13 TPC TEMPERATRE ( C) LTC139 TPC
5 LTC13 PI F CTIO S : V Input Supply Pin. This pin should be decoupled with a.1µf ceramic capacitor. GND: Ground Pin. ON/OFF: TTL/CMOS Compatible Shutdown Pin. A logic low puts the device in the Shutdown mode. Both driver outputs are forced into three-state and the supply current is.µa. V + : Positive Supply Output (RS3 Drivers). V + V. This pin requires an external capacitor C =.1µF for charge storage. The capacitor may be tied to ground or. With multiple devices, the V + and V pins may share a common capacitor. For large numbers of devices, increasing the size of the shared common storage capacitors is recommended to reduce ripple. V : Negative Supply Output (RS3 Drivers). V ( V). This pin requires an external capacitor C =.1µF for charge storage. C1 +, C1, C +, C : Commutating Capacitor Inputs. These pins require two external capacitors C =.1µF: one from C1 + to C1 and another from C + to C. To maintain charge pump efficiency, the capacitor s effective series resistance should be less than Ω. TR IN: RS3 Driver Input Pins. Inputs are TTL/CMOS compatible. The inputs of unused drivers can be left unconnected since 3k input pull-up resistors to are included on chip. To minimize power consumption, the internal driver pull-up resistors are disconnected from in the Shutdown mode. TR OT: Driver Outputs at RS3 Voltage Levels. Outputs are in a high impedance state when in the Shutdown or = V. The driver outputs are protected against ESD to ±1kV for human body model discharges. RX IN: Receiver Inputs. These pins can be forced to ±V without damage. The receiver inputs are protected against ESD to ±1kV for human body model discharges. Each receiver provides.v of hysteresis for noise immunity. RX OT: Receiver Outputs with TTL/CMOS Voltage Levels. Outputs are in a high impedance state when in the Shutdown mode. W W SWITCHI G TI E WAVEFOR S INPT 1.V 1.V V RX INPT 1.7V 1.3V V t LHD V t HLD V V + V RX t LHR.V t HLR.V V LTC13 F1 LTC13 F Figure 1. Driver Propagation Delay Timing Figure. Receiver Propagation Delay Timing
6 LTC13 TEST CIRCITS Driver Timing Test Load Receiver Timing Test Load INPT 1pF 3k RX INPT RX RX 1pF LTC13 TA3 LTC13 TA ESD Test Circuit.1µF 17 3 = V LTC13 7.1µF.1µF LOGIC INPT LOGIC INPT LOGIC k 3k k 1 1.1µF INPT RS3 LINE PINS PROTECTED TO ±1kV LOGIC ON/OFF 1 1 k INPT LTC13 TA
7 LTC13 PACKAGE DESCRIPTIO N Package 1-Lead PDIP (Narrow.3 Inch) (Reference LTC DWG # --11).9* (.) MAX ±.1* (.77 ±.31).3.3 (7..).13 ±. (3.3 ±.17) ( ).9.1 (.9.31) ( ). (.) MIN.1 (3.17) MIN. (.17) MIN NOTE: INCHES 1. DIMENSIONS ARE MILLIMETERS *THESE DIMENSIONS DO NOT INCLDE MOLD FLASH OR PROTRSIONS. MOLD FLASH OR PROTRSIONS SHALL NOT EXCEED.1 INCH (.mm).1 (.) BSC. (1.1) TYP.1 ±.3 (.7 ±.7) N1 SW Package 1-Lead Plastic Small Outline (Wide.3 Inch) (Reference LTC DWG # --1).3 ±. TYP N. BSC. ± ( ) NOTE MIN.3 ±. N NOTE ( ) 1 3 N/ N/ RECOMMENDED SOLDER PAD LAYOT. (.17) RAD MIN ( ) NOTE.1.9 (..737) TYP.93.1 (.3.) ( ) (1.7) (.9.33) NOTE 3 BSC (.3.) (. 1.7) NOTE: TYP INCHES 1. DIMENSIONS IN (MILLIMETERS). DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANFACTRING OPTIONS. THE PART MAY BE SPPLIED WITH OR WITHOT ANY OF THE OPTIONS. THESE DIMENSIONS DO NOT INCLDE MOLD FLASH OR PROTRSIONS. MOLD FLASH OR PROTRSIONS SHALL NOT EXCEED." (.1mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights...1 (.1.3) S1 (WIDE) 7
8 LTC13 RELATED PARTS PART NMBER DESCRIPTION COMMENTS LT17/LT171 V, Driver, Receiver RS3 Transeivers ±1kV ESD per IEC 1- LTC133 V, Driver, Receiver RS3 Transceiver µa Supply Current, Narrow 1-pin SO LTC13 V, Driver, Receiver RS3 Transceiver µa Supply Current, Receivers Active in Shutdown LTC13 3.3V, Driver, Receiver RS Transceiver µa Supply Current, Receivers Active in Shutdown LTC13 3.3V, Driver, Receiver RS Transceiver µa Supply Current, Narrow 1-pin SO Linear Technology Corporation 13 McCarthy Blvd., Milpitas, CA () 3-19 FAX: () 3-7 linear.com LW/TP 1 1K REV A PRINTED IN SA LINEAR TECHNOLOGY CORPORATION 199
DESCRIPTIO TYPICAL APPLICATIO. LTC1383 5V Low Power RS232 Transceiver FEATURES APPLICATIO S
LTC V Low Power RS Transceiver FEATRES Operates from a Single V Supply Low Supply Current: I CC = µa ESD Protection Over ±kv Available in -Pin SOIC Narrow Package ses Small Capacitors: Operates to kbaud
More informationLT1780/LT1781 Low Power 5V RS232 Dual Driver/Receiver with ±15kV ESD Protection DESCRIPTIO
FEATRES ma Max Supply Current ESD Protection to IEC -- Level ±1kV Air Gap, ±kv Contact ses Small Capacitors:.1µF kbaud Operation for R L = 3k, C L = pf kbaud Operation for R L = 3k, C L = pf Outputs Withstand
More informationLT1342 5V RS232 Transceiver with 3V Logic Interface DESCRIPTIO
V RS Transceiver with V Logic Interface FEATRES ESD Protection Over ±kv V Logic Interface ses Small Capacitors:.µF,.µF µa Supply Current in Shutdown Low Power Driver Disable Operating Mode Pin Compatible
More informationDESCRIPTIO FEATURES TYPICAL APPLICATIO. LT1080/LT1081 Advanced Low Power 5V RS232 Dual Driver/Receiver APPLICATIO S
Advanced Low Power V RS Dual Driver/Receiver FEATRES Superior to CMOS Improved Speed: Operates over kbaud Improved Protection: Outputs Can Be Forced to ±0V without Damage Three-State Outputs Are High Impedance
More informationDESCRIPTIO TYPICAL APPLICATION. LT1130A/LT1140A Series Advanced Low Power 5V RS232 Drivers/Receivers with Small Capacitors
FEATRES ESD Protection over ±kv (±kv IEC--- for LTA, LTA and LTA) ses Small Capacitors:.µF,.µF µa Supply Current in SHTDOWN kbaud Operation for R L = k, C L = pf kbaud Operation for R L = k, C L = pf CMOS
More informationDESCRIPTIO. LTC V Micropower EIA/TIA-562 Transceiver U S
3.3V Micropower EIA/TIA-6 Transceiver FEATRES Low Supply Current 3µA.µA Supply Current in SHTDOWN ESD Protection ±1kV Operates From a Single 3.3V Supply ses Small Capacitors.1µF Operates To 1k Baud Three-State
More informationDESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. LT1039A/LT1039A-16 Triple RS232 Driver/Receiver with Shutdown
FEATRES On-Chip ESD Protection: ±15kV Human Body Model ±15kV IEC-00-4-2 Air Gap Test** ±8kV IEC-00-4-2 Contact Test 125kBd Operation with 3kΩ/2500pF Load 250kBd Operation with 3kΩ/00pF Load Operates from
More informationDESCRIPTIO. LTC1338 5V Low Power RS232 5-Driver/3-Receiver Transceiver
V Low Power RS3 -Driver/3-Receiver Transceiver FEATRES Low Supply Current: µa.µa Supply Current in SHTDON µa Supply Current in RECEIVER ALIVE Mode ESD Protection Over ±1kV Operates from a Single V Supply
More informationFEATURES DESCRIPTIO APPLICATIO S TYPICAL APPLICATIO. LTC1046 Inductorless 5V to 5V Converter
LTC Inductorless V to V Converter FEATRES ma Output Current Plug-In Compatible with ICL/LTC R OT = Ω Maximum µa Maximum No Load Supply Current at V Boost Pin (Pin ) for Higher Switching Frequency 9% Minimum
More informationDESCRIPTIO. LTC1446/LTC1446L Dual 12-Bit Rail-to-Rail Micropower DACs in SO-8
Dual 12-Bit Rail-to-Rail Micropower DACs in SO-8 FEATRES Dual DACs with 12-Bit Resolution SO-8 Package Rail-to-Rail Output Amplifiers 3V Operation (LTC1446L): I CC = 65µA Typ 5V Operation (LTC1446): I
More informationDESCRIPTIO. LTC1323 Single 5V AppleTalk Transceiver
LTC Single V AppleTalk Transceiver FEATRES Single Chip Provides Complete LocalTalk /AppleTalk Port Operates From a Single V Supply ESD Protection to ±0kV on Receiver Inputs and Driver Outputs Low Power:
More informationFEATURES DESCRIPTIO APPLICATIO S LTC1451 LTC1452/LTC Bit Rail-to-Rail Micropower DACs in SO-8 TYPICAL APPLICATIO
12-Bit Rail-to-Rail Micropower DACs in SO-8 FEATRES 12-Bit Resolution Buffered True Rail-to-Rail Voltage Output 3V Operation (LTC1453), I CC : 250µA Typ 5V Operation (), I CC : 400µA Typ 3V to 5V Operation
More informationDistributed by: www.jameco.com -8-83-4242 The content and copyrights of the attached material are the property of its owner. FEATRES Regulates While Sourcing or Sinking Current Provides Termination for
More informationDESCRIPTIO. LT685 High Speed Comparator FEATURES APPLICATIO S TYPICAL APPLICATIO
High Speed Comparator FEATRES ltrafast (5.5ns typ) Complementary ECL Output 50Ω Line Driving Capability Low Offset Voltage Output Latch Capability External Hysteresis Control Pin Compatible with Am685
More informationDESCRIPTIO APPLICATIO S TYPICAL APPLICATIO LTC1921 Dual 48V Supply and Fuse Monitor FEATURES
LTC9 Dual Supply and Fuse Monitor FEATRES Withstands Transient Voltages p to V/V Requires No Precision External Components Independently Monitors Two Supplies for ndervoltage Faults:.V ±V MAX Overvoltage
More informationFEATURES TYPICAL APPLICATIO LTC MHz to 3GHz RF Power Detector. in SC70 Package DESCRIPTIO APPLICATIO S
300MHz to 3GHz RF Power Detector in SC70 Package FEATRES Temperature Compensated Internal Schottky Diode RF Detector Wide Input Frequency Range: 300MHz to 3GHz Wide Input Power Range: 30dBm to 6dBm Buffered
More informationFEATURES APPLICATIO S TYPICAL APPLICATIO. LTC Low Noise, 8th Order, Clock Sweepable Elliptic Lowpass Filter DESCRIPTIO
LTC- Low Noise, th Order, Clock Sweepable Elliptic Lowpass Filter FEATRES th Order Filter in a -Pin Package No External Components : Clock to Center Ratio µv RMS Total Wideband Noise.% THD or Better khz
More informationTYPICAL APPLICATIO. LT MHz, 250V/µs, A V 4 Operational Amplifier DESCRIPTIO FEATURES APPLICATIO S
5MHz, 5V/µs, A V Operational Amplifier FEATRES Gain-Bandwidth: 5MHz Gain of Stable Slew Rate: 5V/µs Input Noise Voltage: nv/ Hz C-Load TM Op Amp Drives Capacitive Loads Maximum Input Offset Voltage: µv
More informationFEATURES DESCRIPTIO TYPICAL APPLICATIO. LM / LM /LM Micropower Voltage Reference APPLICATIO S
Micropower Voltage Reference FEATRES 2µA to 2mA Operating Range Guaranteed % Initial Voltage Tolerance Guaranteed Ω Dynamic Impedance Very Low Power Consumption APPLICATIO S Portable Meter References Portable
More informationAPPLICATIO S TYPICAL APPLICATIO. LTC1482 Low Power RS485 Transceiver with Carrier Detect and Receiver Fail-Safe DESCRIPTIO FEATURES
FEATRES No Damage or Latchup to ±15kV (Human Body Model), IEC1-4-2 Level 4 (±8kV) Contact and Level 3 (±8kV) Air Discharge Active Low Carrier Detect Output Guaranteed High Receiver Output State for Floating,
More informationFEATURES TYPICAL APPLICATIO. LTC Low Power 8th Order Pin Selectable Butterworth or Bessel Lowpass Filter DESCRIPTIO APPLICATIO S
FEATRES Pin Selectable Butterworth or Bessel Response ma Supply Current with ±V Supplies f CTOFF up to khz µv RMS Wideband Noise THD
More informationFEATURES APPLICATIONS TYPICAL APPLICATION. LTC1451 LTC1452/LTC Bit Rail-to-Rail Micropower DACs in SO-8 DESCRIPTION
12-Bit Rail-to-Rail Micropower DACs in SO-8 FEATRES 12-Bit Resolution Buffered True Rail-to-Rail Voltage Output 3V Operation (LTC1453), I CC : 250µA Typ 5V Operation (), I CC : 400µA Typ 3V to 5V Operation
More informationVID Controlled High Current 4-Phase DC/DC Converter (Simplified Block Diagram) 4.5V TO 22V V OS TG1 INTV CC SW1 LTC1629 BG1 PGND SGND TG2 EAIN SW2
FEATRES Fully Compliant with the Intel RM 8. ID Specification Programs Regulator Output oltage from.0 to.8 in m Steps Programs an Entire Family of Linear Technology DC/DC Converters with 0.8 References
More informationDESCRIPTIO FEATURES APPLICATIO S. LT1129/LT /LT Micropower Low Dropout Regulators with Shutdown TYPICAL APPLICATIO
Micropower Low Dropout Regulators with Shutdown FEATRES.4V Dropout Voltage 7mA Output Current µa Quiescent Current No Protection Diodes Needed Adjustable Output from 3.8V to 3V 3.3V and V Fixed Output
More informationFEATURES TYPICAL APPLICATIO. LTC1443/LTC1444/LTC1445 Ultralow Power Quad Comparators with Reference DESCRIPTIO APPLICATIO S
LTC/LTC/LTC ltralow Power Quad Comparators with Reference FEATRES ltralow Quiescent Current:.µA Max Reference Output Drives.µF Capacitor Adjustable Hysteresis (LTC/LTC) Wide Supply Range Single: V to V
More informationLTC1515 Series Step-Up/Step-Down Switched Capacitor DC/DC Converters with Reset DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION
LTC Series Step-p/Step-Down Switched Capacitor DC/DC Converters with Reset FEATRES Adjustable/Selectable 3V, 3.3V or V Output Voltages V to V Input Voltage Range p to ma Output Current Only Three External
More informationDistributed by: www.jameco.com --- The content and copyrights of the attached material are the property of its owner. LTC Micropower Quad -Bit DAC FEATRES Tiny: DACs in the Board Space of an SO- Micropower:
More informationDESCRIPTION FEATURES APPLICATIONS. LT1313 Dual PCMCIA VPP Driver/Regulator TYPICAL APPLICATION
Dual PCMCIA VPP Driver/Regulator FEATRES Digital Selection of V, V CC, 12V or Hi-Z Output Current Capability: 12mA Internal Current Limiting and Thermal Shutdown Automatic Switching from 3.3V to Powered
More informationFEATURES DESCRIPTIO APPLICATIO S. LTC2050/LTC2050HV Zero-Drift Operational Amplifiers in SOT-23 TYPICAL APPLICATION
FEATRES Maximum Offset Voltage of µv Maximum Offset Voltage Drift of nv/ C Noise:.µV P-P (.Hz to Hz Typ) Voltage Gain: db (Typ) PSRR: db (Typ) CMRR: db (Typ) Supply Current:.8mA (Typ) Supply Operation:.7V
More informationLT1106. DC/DC Converter for PCMCIA Card Flash Memory DESCRIPTIO OBSOLETE:
FOR INFORMATION PRPOSES ONLY OBSOLETE: Contact Linear Technology for Potential Replacement FEATRES 60mA Output Current at 12V from 3V Supply Shutdown to 10µA Programmable 12V or 5V Output p to 85% Efficiency
More informationFEATURES DESCRIPTIO APPLICATIO S. LT1120 Micropower Regulator with Comparator and Shutdown TYPICAL APPLICATIO
LT Micropower Regulator with Comparator and Shutdown FEATRES μa Supply Current ma Output Current.V Reference Voltage Reference Output Sources ma and Sinks ma Open Collector Comparator Sinks ma Logic Shutdown.V
More information5-Bit VID-Controlled High Current Application (Simplified Block Diagram) 4.5V TO 22V LTC TG1 SW1 BG1 PGND TG2 SW2 BG2 4.5V TO 22V LTC TG1
LTC0- -Bit ID oltage Programmer for AMD Opteron CPs FEATRES Programs Regulator Output oltage Range from 0. to. in m Steps Programs a Wide Range of Linear Technology DC/DC Converters with a 0. Reference
More informationFEATURES APPLICATIONS TYPICAL APPLICATION LT1466L/LT1467L Micropower Dual/Quad Precision Rail-to-Rail Input and Output Op Amps
Micropower Dual/Quad Precision Rail-to-Rail Input and Output Op Amps FEATRES Rail-to-Rail Input and Output Low Supply Current: 75µA Max 39µV V OS(MAX) for V CM = V to V + High Common Mode Rejection Ratio:
More informationFEATURES U U PRECO DITIO I G APPLICATIO S TYPICAL APPLICATIO. LT1033 3A Negative Adjustable Regulator DESCRIPTIO
NOT RECOMMENDED FOR NEW DESIGNS Contact Linear Technology for Potential Replacement FEATRES Guaranteed 1% Initial Voltage Tolerance Guaranteed.15%/V Line Regulation Guaranteed.2%/ W Thermal Regulation
More informationDESCRIPTIO. LTC Low Power, 8th Order Progressive Elliptic, Lowpass Filter
LTC9- Low Power, th Order Progressive Elliptic, Lowpass Filter FEATRES th Order Elliptic Filter in SO- Package Operates from Single.V to ±V Power Supplies db at.f CTOFF db at.f CTOFF db at f CTOFF Wide
More informationV ON = 0.93V V OFF = 0.91V V ON = 2.79V V OFF = 2.73V V ON = 4.21V V OFF = 3.76V V ON = 3.32V V OFF = 2.80V. 45.3k 6.04k 1.62k. 3.09k. 7.68k 1.
FEATURES Fully Sequence Four Supplies Six with Minimal External Circuitry Cascadable for Additional Supplies Power Off in Reverse Order or Simultaneously Charge Pump Drives External MOSFETs Drives Power
More informationDistributed by: www.jameco.com --3-44 The content and copyrights of the attached material are the property of its owner. MHz, 3nV/ Hz, A V Operational Amplifier FEATRES Gain-Bandwidth: MHz Gain of Stable
More informationFEATURES TYPICAL APPLICATIO. LT1194 Video Difference Amplifier DESCRIPTIO APPLICATIO S
FEATURES Differential or Single-Ended Gain Block: ± (db) db Bandwidth: MHz Slew Rate: /µs Low Cost Output Current: ±ma Settling Time: ns to.% CMRR at MHz: db Differential Gain Error:.% Differential Phase
More informationFEATURES DESCRIPTIO APPLICATIO S. LT1636 Over-The-Top Micropower Rail-to-Rail Input and Output Op Amp TYPICAL APPLICATIO
Over-The-Top Micropower Rail-to-Rail Input and Output Op Amp FEATRES Rail-to-Rail Input and Output Micropower: 5µA I Q, 44V Supply MSOP Package Over-The-Top TM : Input Common Mode Range Extends 44V Above
More informationFEATURES APPLICATIO S. LT1178/LT µA Max, Dual and Quad, Single Supply, Precision Op Amps DESCRIPTIO TYPICAL APPLICATIO
FEATRES 7µA Max Supply Current per Amplifier 7µV Max Offset Voltage 5pA Max Offset Current 5nA Max Input Bias Current.9µV P-P.Hz to Hz Voltage Noise.5pA P-P.Hz to Hz Current Noise.5µV/ C Offset Voltage
More informationV ON = 2.64V V OFF = 1.98V V ON = 0.93V V OFF = 0.915V V ON = 3.97V V OFF = 2.97V. V ON = 2.79V V OFF = 2.73V 100k 1.62k 66.5k. 6.04k.
FEATURES Fully Sequence and Monitor Four Supplies Six with Minimal External Circuitry Cascadable for Additional Supplies Power Off in Reverse Order or Simultaneously Charge Pump Drives External MOSFETs
More informationDESCRIPTIO FEATURES. LTC1065 DC Accurate, Clock-Tunable Linear Phase 5th Order Bessel Lowpass Filter APPLICATIO S TYPICAL APPLICATIO
FEATRES Clock-Tunable Cutoff Frequency mv DC Offset (Typical) db CMR (Typical) Internal or External Clock µv RMS Clock Feedthrough : Clock-to-Cutoff Frequency Ratio µv RMS Total Wideband Noise.% Noise
More informationAPPLICATIONS TYPICAL APPLICATION. LTC1841/LTC1842/LTC1843 Ultralow Power Dual Comparators with Reference DESCRIPTION FEATURES
LTC/LTC/LTC3 ltralow Power Dual Comparators with Reference FEATRES ltralow Quiescent Current: 3.µA Typ Open-Drain Outputs Typically Sink Greater Than ma Wide Supply Range: (LTC) Single: V to V Dual: ±V
More informationLTC1518/LTC Mbps Precision Delay RS485 Quad Line Receivers DESCRIPTIO FEATURES APPLICATIO S TYPICAL APPLICATIO
FEATRES Precision Propagation Delay: 8.ns ±.ns Over C to C Temperature Range High Data Rate: Mbps Low t PLH /t PHL Skew: ps Typ Low Channel-to-Channel Skew: ps Typ Guaranteed Fail-Safe Operation over the
More informationDESCRIPTION FEATURES APPLICATIONS. LTC / LTC /LTC1329A-50 Micropower 8-Bit Current Output D/A Converter TYPICAL APPLICATION
LTC9-/ LTC9-/LTC9A- Micropower -Bit Current Output D/A Converter FEATRES Guaranteed Precision Full-Scale DAC Output Current at C: LTC9A- µa ±% LTC9- µa ±% LTC9- µa ±% Wide Output Voltage DC Compliance:
More informationAPPLICATIO S TYPICAL APPLICATIO. LT V Single Supply Video Difference Amplifier FEATURES DESCRIPTIO
FEATRES Differential or Single-Ended Gain Block Wide Supply Range V to.v Output Swings Rail-to-Rail Input Common Mode Range Includes Ground V/µs Slew Rate db Bandwidth = 7MHz, A V = ± CMRR at MHz: >db
More informationLow Power, 3.3 V, RS-232 Line Drivers/Receivers ADM3202/ADM3222/ADM1385
a FEATURES kbps Data Rate Specified at 3.3 V Meets EIA-3E Specifications. F Charge Pump Capacitors Low Power Shutdown (ADM3E and ADM35) DIP, SO, SOIC, SSOP and TSSOP Package Options Upgrade for MAX3/3
More informationDESCRIPTIO. LT1413 Single Supply, Dual Precision Op Amp
Single Supply, Dual Precision Op Amp FEATRES Single Supply Operation: Input Goes Below Ground Output Swings to Ground Sinking Current No Pull-Down Resistors Needed Phase Reversal Protection At V, V Low
More informationFEATURES TYPICAL APPLICATIO. LT1635 Micropower Rail-to-Rail Op Amp and Reference DESCRIPTIO APPLICATIO S
LT5 Micropower Rail-to-Rail Op Amp and Reference FEATRES Guaranteed Operation at.v Op Amp and Reference on Single Chip Micropower: µa Supply Current Industrial Temperature Range SO- Packages Rail-to-Rail
More informationDESCRIPTIO FEATURES TYPICAL APPLICATIO. LT mA, Low Noise, Low Dropout Negative Micropower Regulator in ThinSOT APPLICATIO S
2mA, Low Noise, Low Dropout Negative Micropower Regulator in ThinSOT FEATRES Low Profile (1mm) ThinSOT TM Package Low Noise: 3µV RMS (1Hz to 1kHz) Low Quiescent Current: 3µA Low Dropout Voltage: 34mV Output
More informationDESCRIPTION FEATURES. LTC1550/LTC1551 Low Noise, Switched Capacitor Regulated Voltage Inverters APPLICATIONS TYPICAL APPLICATION
LTC55/LTC55 Low Noise, Switched Capacitor Regulated Voltage Inverters FEATRES Regulated Negative Voltage from a Single Positive Supply Low Output Ripple: Less Than mv P-P Typ High Charge Pump Frequency:
More informationTYPICAL APPLICATIO. LT1027 Precision 5V Reference FEATURES DESCRIPTIO APPLICATIO S
Precision 5V Reference FEATRES Very Low Drift: 2ppm/ C Max TC Pin Compatible with LT121-5, REF-2, (PDIP Package) Output Sources 15mA, Sinks 1mA Excellent Transient Response Suitable for A-to-D Reference
More informationFEATURES DESCRIPTIO TYPICAL APPLICATIO LT MHz to 3GHz RF Power Detector. with 60dB Dynamic Range APPLICATIO S
LT4 MHz to GHz Power Detector with 6dB Dynamic Range FEATRES Frequency Range: MHz to GHz Linear Dynamic Range: 6dB Exceptional Accuracy over Temperature and Power Supply Fast Transient Response: 8ns Full-Scale
More informationDESCRIPTIO FEATURES APPLICATIO S. LTC1063 DC Accurate, Clock-Tunable 5th Order Butterworth Lowpass Filter TYPICAL APPLICATIO
FEATRES Clock-Tunable Cutoff Frequency mv DC Offset (Typical) db CMRR (Typical) Internal or External Clock µv RMS Clock Feedthrough : Clock-to-Cutoff Frequency Ratio 9µV RMS Total Wideband Noise.% THD
More informationDESCRIPTIO FEATURES TYPICAL APPLICATIO. LTC1250 Very Low Noise Zero-Drift Bridge Amplifier APPLICATIO S
LTC Very Low Noise Zero-Drift Bridge Amplifier FEATRES Very Low Noise:.µV P-P Typ,.Hz to Hz DC to Hz Noise Lower Than OP- Full Output Swing into k Load Offset Voltage: µv Max Offset Voltage Drift: nv/
More informationFEATURES. LT1612 Synchronous, Step-Down 800kHz PWM DC/DC Converter DESCRIPTIO APPLICATIO S TYPICAL APPLICATION
Synchronous, Step-Down 8kHz PWM DC/DC Converter FEATRES Operates from Input Voltage As Low As 2V Internal.7A Synchronous Switches ses Ceramic Input and Output Capacitors 62mV Reference Voltage 8kHz Fixed
More informationDistributed by: www.jameco.com --- The content and copyrights of the attached material are the property of its owner. Precision, Rail-to-Rail, Zero-Drift, Resistor-Programmable Instrumentation Amplifier
More informationDESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. LT1498/LT MHz, 6V/µs, Dual/Quad Rail-to-Rail Input and Output Precision C-Load Op Amps
MHz, 6V/µs, Dual/Quad Rail-to-Rail Input and Output Precision C-Load Op Amps FEATRES Rail-to-Rail Input and Output 475µV Max V OS from V + to V Gain-Bandwidth Product: MHz Slew Rate: 6V/µs Low Supply Current
More informationFEATURES DESCRIPTIO APPLICATIO S BLOCK DIAGRA. LT1054/LT1054L Switched-Capacitor Voltage Converter with Regulator
Switched-Capacitor Voltage Converter with Regulator FEATRES Available in Space Saving SO-8 Package Output Current: ma (LT54 5mA (LT54L Reference and Error Amplifier for Regulation Low Loss:.V at ma Operating
More informationFEATURES DESCRIPTIO TYPICAL APPLICATIO. LT1020 Micropower Regulator and Comparator APPLICATIO S
Micropower Regulator and Comparator FEATRES Input Voltage Range:. to V µa Supply Current ma Output Current. Reference Voltage Reference Output Sources ma and Sinks.mA Dual Output Comparator Comparator
More informationDESCRIPTION FEATURES. LT1490/LT1491 Dual and Quad Micropower Rail-to-Rail Input and Output Op Amps APPLICATIONS TYPICAL APPLICATION
FEATRES Rail-to-Rail Input and Output Single Supply Input Range:.4V to 44V Micropower: µa/amplifier Max Specified on 3V, 5V and ±5V Supplies High Output Current: ma Output Drives,pF with Output Compensation
More informationDESCRIPTIO FEATURES APPLICATIO S. LT GHz to 2.7GHz Receiver Front End TYPICAL APPLICATIO
1.GHz to 2.GHz Receiver Front End FEATURES 1.V to 5.25V Supply Dual LNA Gain Setting: +13.5dB/ db at Double-Balanced Mixer Internal LO Buffer LNA Input Internally Matched Low Supply Current: 23mA Low Shutdown
More informationFEATURES TYPICAL APPLICATIO. LT6550/LT V Triple and Quad Video Amplifiers DESCRIPTIO APPLICATIO S
FEATRES Single Supply Operation from V to.v Small (mm mm) MSOP -Lead Package Internal Resistors for a Gain of Two V/µs Slew Rate MHz db Bandwidth MHz Flat to.db % Settling Time: ns Input Common Mode Range
More informationOBSOLETE TTL/CMOS INPUTS* TTL/CMOS OUTPUTS TTL/CMOS TTL/CMOS OUTPUTS DO NOT MAKE CONNECTIONS TO THESE PINS INTERNAL 10V POWER SUPPLY
a FEATURES kb Transmission Rate ADM: Small (. F) Charge Pump Capacitors ADM3: No External Capacitors Required Single V Power Supply Meets EIA-3-E and V. Specifications Two Drivers and Two Receivers On-Board
More informationAPPLICATIONS LT1351. Operational Amplifier DESCRIPTION FEATURES TYPICAL APPLICATION
FEATRES 3MHz Gain Bandwidth V/µs Slew Rate 5µA Supply Current Available in Tiny MSOP Package C-Load TM Op Amp Drives All Capacitive Loads nity-gain Stable Power Saving Shutdown Feature Maximum Input Offset
More informationFEATURES DESCRIPTIO. LTC Linear Phase, DC Accurate, Low Power, 10th Order Lowpass Filter APPLICATIO S TYPICAL APPLICATIO
Linear Phase, DC Accurate, Low Power, 0th Order Lowpass Filter FEATRES One External R Sets Cutoff Frequency Root Raised Cosine Response ma Supply Current with a Single Supply p to khz Cutoff on a Single
More informationABSOLTE MAXIMM RATINGS W W W... 7V Operating Junction Temperature Range Control Section... 0 C to 125 C Power Transistor... 0 C to 150 C Storage Tempe
FEATRES Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation: 0.05% Typ Trimmed Current Limit On-Chip Thermal Limiting APPLICATIONS Intel Pentium Pro Processor GTL Supply
More informationAPPLICATIO S. LT /LT1585A-1.5 Fixed 1.5V, 4.6A and 5A Low Dropout, Fast Response GTL+ Regulators DESCRIPTIO FEATURES TYPICAL APPLICATIO
FEATRES Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation: 0.05% Typ Trimmed Current Limit On-Chip Thermal Limiting APPLICATIO S GTL+ Power Supply Low Voltage Logic
More information5-Bit VID-Controlled High Current 4-Phase Application (Simplified Block Diagram) 4.5V TO 22V LTC1629 TG1 SW1 BG1 PGND TG2 SW2 BG2 4.
-Bit Desktop VID Voltage Programmer FEATRES Programs Regulator Output Voltage Range from.v to.v in mv Steps and from.v to.v in mv Steps (VRM 8.) Programs a Wide Range of Linear Technology DC/DC Converters
More informationVID Controlled High Current 4-Phase DC/DC Converter (Simplified Block Diagram) 4.5V TO 22V TG1 SW1 LTC1629 BG1 PGND TG2 SW2 BG2 4.
FEATRES Fully Compliant with the Intel VRM./. VID Specification Programs Regulator Output Voltage from.v to.8v in mv Steps Programs an Entire Family of Linear Technology DC/DC Converters ±.% Accurate Voltage
More informationHigh Speed, +5 V, 0.1 F CMOS RS-232 Driver/Receivers ADM202/ADM203
a FEATURES kb Transmission Rate ADM: Small (. F) Charge Pump Capacitors ADM: No External Capacitors Required Single V Power Supply Meets EIA--E and V. Specifications Two Drivers and Two Receivers On-Board
More informationDistributed by: www.jameco.com -8-8-22 The content and copyrights of the attached material are the property of its owner. FEATRES Input Bias Current, Warmed p: pa Max % Tested Low Voltage Noise: 8nV/ Hz
More informationDESCRIPTIO APPLICATIO S. LTC5530 Precision 300MHz to 7GHz RF Detector with Shutdown and Gain Adjustment FEATURES TYPICAL APPLICATIO
Precision 3MHz to 7GHz RF Detector with Shutdown and Gain Adjustment FEATURES Temperature Compensated Internal Schottky Diode RF Detector Wide Input Frequency Range: 3MHz to 7GHz* Wide Input Power Range:
More informationDESCRIPTIO APPLICATIO S. LTC5531 Precision 300MHz to 7GHz RF Detector with Shutdown and Offset Adjustment FEATURES TYPICAL APPLICATIO
LTC553 Precision 3MHz to 7GHz RF Detector with Shutdown and Offset Adjustment FEATURES Temperature Compensated Internal Schottky Diode RF Detector Wide Input Frequency Range: 3MHz to 7GHz* Wide Input Power
More informationDESCRIPTION FEATURES APPLICATIONS. LTC1590 Dual Serial 12-Bit Multiplying DAC TYPICAL APPLICATION
FEATRES DNL and INL Over Temperature: ±.LSB Max Gain Error: ±LSB Max Low Supply Current: µa Max -Quadrant Multiplication Power-On Reset Asynchronous Clear Input Daisy-Chain -Wire Serial Interface -Pin
More informationFEATURES APPLICATIO S TYPICAL APPLICATIO. LT1102 High Speed, Precision, JFET Input Instrumentation Amplifier (Fixed Gain = 10 or 100) DESCRIPTIO
FEATRES Slew Rate: V/μs Gain-Bandwidth Product: MHz Settling Time (.%): μs Overdrive Recovery:.μs Gain Error:.% Max Gain Drift: ppm/ C Gain Nonlinearity: ppm Max Offset Voltage (Input Output): μv Max Drift
More informationLTC1664 Micropower Quad 10-Bit DAC. Applications. Block Diagram
LTC Micropower Quad -Bit DAC Features n Tiny: DACs in the Board Space of an SO- n Micropower: µa per DAC Plus µa Sleep Mode for Extended Battery Life n Wide.V to.v Supply Range n Rail-to-Rail Voltage Outputs
More informationHigh Speed, +5 V, 0.1 µf CMOS RS-232 Drivers/Receivers ADM222/ADM232A/ADM242*
a FEATURES 00 kb/s Transmission Rate Small (0. µf) Charge Pump Capacitors Single V Power Supply Meets All EIA--E and V. Specifications Two Drivers and Two Receivers On-Board DC-DC Converters ± V Output
More informationDESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. January 1998
Final Electrical Specifications Single Cell High Current Micropower 00kHz Boost DC/DC Converter January 1998 FEATRES 5V at 1A from a Single Li-Ion Cell 3.3V at 300mA from a Single NiCd Cell Low Quiescent
More informationHigh-Speed, 5 V, 0.1 F CMOS RS-232 Drivers/Receivers ADM222/ADM232A/ADM242
a FEATURES 200 kb/s Transmission Rate Small (0. F) Charge Pump Capacitors Single V Power Supply Meets All EIA-232-E and V.2 Specifications Two Drivers and Two Receivers On-Board DC-DC Converters V Output
More informationAPPLICATIO S TYPICAL APPLICATIO. LTC2051/LTC2052 Dual/Quad Zero-Drift Operational Amplifiers FEATURES DESCRIPTIO
LTC/LTC Dual/Quad Zero-Drift Operational Amplifiers FEATRES Maximum Offset Voltage of μv Maximum Offset Voltage Drift of nv/ C Small Footprint, Low Profile MS/GN Packages Single Supply Operation:.V to
More informationFEATURES APPLICATIO S. LTC1799 1kHz to 33MHz Resistor Set SOT-23 Oscillator DESCRIPTIO TYPICAL APPLICATIO
FEATRES One External Resistor Sets the Frequency Fast Start-p Time:
More informationDESCRIPTIO TYPICAL APPLICATION. LT1207 Dual 250mA/60MHz Current Feedback Amplifier APPLICATIO S
LT27 Dual 25mA/6MHz Current Feedback Amplifier FEATRES 25mA Minimum Output Drive Current 6MHz Bandwidth, A V = 2, R L = Ω 9V/µs Slew Rate, A V = 2, R L = 5Ω.2% Differential Gain, A V = 2, R L = 3Ω.7 Differential
More informationLTC Bit Rail-to-Rail Micropower DAC in MSOP Package FEATURES
12-Bit Rail-to-Rail Micropower DAC in MSOP Package FEATURES Buffered True Rail-to-Rail Voltage Output Maximum DNL Error:.5LSB 12-Bit Resolution Supply Operation: 3V to 5V Output Swings from V to V REF
More informationDESCRIPTIO FEATURES APPLICATIO S TYPICAL APPLICATIO. LT1813/LT1814 Dual/Quad 3mA, 100MHz, 750V/µs Operational Amplifiers
/ LT8 FEATRES MHz Gain Bandwidth Product 75V/µs Slew Rate 3.6mA Maximum Supply Current per Amplifier Tiny 3mm x 3mm x.8mm DFN Package 8nV/ Hz Input Noise Voltage nity-gain Stable.5mV Maximum Input Offset
More informationFEATURES U APPLICATIO S TYPICAL APPLICATIO. LTC1860L/LTC1861L µpower, 3V, 12-Bit, 150ksps 1- and 2-Channel ADCs in MSOP DESCRIPTIO
LTCL/LTCL µpower, V, -Bit, ksps - and -Channel ADCs in MSOP FEATRES -Bit ksps ADCs in MSOP Package Single V Supply Low Supply Current: µa (Typ) Auto Shutdown Reduces Supply Current to µa at ksps True Differential
More informationDESCRIPTIO FEATURES TYPICAL APPLICATIO. LTC1550L/LTC1551L Low Noise, Switched Capacitor Regulated Voltage Inverters APPLICATIO S
FEATRES Regulated Negative Voltage from a Single Positive Supply Low Output Ripple: Less Than mv P-P Typ High Charge Pump Frequency: 9kHz Small Charge Pump Capacitors:.µF Requires Only Four External Capacitors
More informationDistributed by: www.jameco.com --- The content and copyrights of the attached material are the property of its owner. FEATRES Supply Current µa (Max per Amplifier) Guaranteed Over Temperature Offset Voltage
More informationFEATURES TYPICAL APPLICATIO. LT µA, 14nV/ Hz, Rail-to-Rail Output Precision Op Amp with Shutdown DESCRIPTIO APPLICATIO S
FEATURES 3µV Maximum Offset Voltage pa Maximum Input Bias Current 3µA Supply Current Rail-to-Rail Output Swing µa Supply Current in Shutdown db Minimum Voltage Gain (V S = ±V).µV/ C Maximum V OS Drift
More informationFEATURES DESCRIPTIO APPLICATIO S. LTC1682/LTC /LTC Doubler Charge Pumps with Low Noise Linear Regulator TYPICAL APPLICATIO
LTC/LTC-./LTC- Doubler Charge Pumps with Low Noise Linear Regulator FEATRES Low Output Noise: µv RMS (khz BW) Adjustable or Fixed Boosted Output Adjustable Output Voltage Range:.V to.v Fixed Output Voltages:.V,
More informationFEATURES DESCRIPTIO TYPICAL APPLICATIO LT V Low Dropout Regulator
Low Dropout Regulator Driver FEATRES Extremely Low Dropout Low Cost Fixed 5V Output, Trimmed to ±1% 7µA Quiescent Current 1mV Line Regulation 5mV Load Regulation Thermal Limit 4A Output Current Guaranteed
More informationLTC1440/LTC1441/LTC1442 Ultralow Power Single/Dual Comparator with Reference DESCRIPTIO FEATURES APPLICATIO S TYPICAL APPLICATIO
LTC/LTC/LTC Ultralow Power Single/Dual Comparator with Reference FEATURES Ultralow Quiescent Current:.µA Typ (LTC) Reference Output Drives.µF Capacitor Adjustable Hysteresis (LTC/LTC) Wide Supply Range:
More informationFEATURES APPLICATIO S. LT GHz to 1.4GHz High Linearity Upconverting Mixer DESCRIPTIO TYPICAL APPLICATIO
FEATURES Wide RF Frequency Range:.7GHz to.ghz 7.dBm Typical Input IP at GHz On-Chip RF Output Transformer On-Chip 5Ω Matched LO and RF Ports Single-Ended LO and RF Operation Integrated LO Buffer: 5dBm
More informationABSOLTE AXI RATI GS (Note 1) (Referred to GND) W W W, SW to 7V SHDN, MODE to 7V V OT to 5.5V V NEG... 17V to 0.3V Operating Tempe
Triple Output Power Supply for Small TFT-LCD Displays FEATRES Generates Three Voltages: 5.1V at 10mA 5V, 10V, or 15V at 500µA 10V or 15V at 500µA Better than 90% Efficiency Low Output Ripple: Less than
More informationFEATURES DESCRIPTIO APPLICATIO S TYPICAL APPLICATIO. LT1024 Dual, Matched Picoampere, Microvolt Input, Low Noise Op Amp
FEATURES Guaranteed Offset Voltage: 5µV Max Guaranteed Bias Current: 5 C: pa Max 55 C to 5 C: 7pA Max Guaranteed Drift:.5µV/ C Max Low Noise,.Hz to Hz:.5µV P-P Guaranteed Supply Current: 6µA Max Guaranteed
More informationDESCRIPTIO FEATURES. LTC A Low Loss Ideal Diode in ThinSOT TM APPLICATIO S TYPICAL APPLICATIO
FEATRES Low Loss Replacement for PowerPath TM OR ing Diodes Small Regulated Forward Voltage (28mV) 2.6A Maximum Forward Current Low Forward ON Resistance (mω Max) Low Reverse Leakage Current (
More informationLTC1443/LTC1444/LTC1445 Ultralow Power Quad Comparators with Reference Description. Features. Applications. Typical Application
Features n Ultralow Quiescent Current:.µA Max n Reference Output Drives.µF Capacitor n Adjustable Hysteresis (LTC/LTC) n Wide Supply Range Single: V to V Dual: ±V to ±.V n Input Voltage Range Includes
More informationLTC1798 Series Micropower Low Dropout References FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION
Micropower Low Dropout References FEATURES n mv Max Dropout at ma Output Current n µa Typical Quiescent Current n.% Max Initial Accuracy n No Output Capacitor Required n Output Sources ma, Sinks ma n ppm/
More informationLT1124/LT1125 Dual/Quad Low Noise, High Speed Precision Op Amps
Dual/Quad Low Noise, High Speed Precision Op Amps % Tested Low Voltage Noise:.7nV/ Hz Typ 4.nV/ Hz Max Slew Rate: 4.5V/µs Typ Gain Bandwidth Product:.5MHz Typ Offset Voltage, Prime Grade: 7µV Max Low Grade:
More information+5 V Powered RS-232/RS-422 Transceiver AD7306
a FEATURES RS-3 and RS- on One Chip Single + V Supply. F Capacitors Short Circuit Protection Excellent Noise Immunity Low Power BiCMOS Technology High Speed, Low Skew RS- Operation C to + C Operations
More information