Application Note AN-1113
|
|
|
- Anissa Ray
- 5 years ago
- Views:
Transcription
1 Application Note AN- IRS and IR Comparison By Jason Nguyen, Min Fang, David New Table of Contents Page Introduction... Block Diagrams... Electrical Characteristic Differences... Figures... Summary...8 Introduction The IRS is a new HVIC product that replaces the IR HVICs and is pin-to-pin compatible with its corresponding predecessor. In many cases, little or no change is necessary to use the new products. This application note describes the various differences between the IRS and the IR HVICs. The IRS is a high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS or LSTTL output, down to. V logic. The output driver features a high pulse current buffer stage designed for minimum driver crossconduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to V.
2 Block Diagrams The IRS and IR share the same block diagram. There are no functional changes between corresponding part numbers. Electrical Characteristic Differences All measurement conditions remain unchanged unless noted. Parameters not mentioned in this document have not changed. Absolute imum Ratings There are no changes in the Absolute imum Ratings. Recommended Operating Conditions There are no changes in the Recommended Operating Conditions.
3 Dynamic Electrical Characteristics Parameter IR IRS Symbol Definition typ max typ max t r Turn-on rise time (Vs = V) t f Turn-off fall time (Vs = V) 8 8 Units ns The IRS has faster rise and fall times when compared to the IR. Static Electrical Characteristics Parameter IR IRS Symbol Definition min typ max min typ max V IH Logic "" input voltage V IL Logic "" input voltage V OH High level output voltage, - V O Io = ma Io = ma V OL Low level output voltage, V O Io = ma Io = ma I O+ Output high short circuit pulsed current (V O = V, VIN=Logic "", PW <= us) I O- Output low short circuit pulsed current (V O = V, VIN = Logic "", PW <= us) - - Units V ma With the IRS,. The V IH has been reduced to. V for better. V logic compatibility.. The V OH and V OL are tested using a new standardized test condition of I O = ma. The output driver s on resistance is slightly lower for IRS.. The typical values for I O+ and I O- are higher, which allows faster switching. Figures This figures shown in this section compare figures shown in the IR (left column) and IRS (right column) datasheets. Illustrations that have not changed between the two datasheets have not been included in this section.
4 IR IRS Turn-On Rise Time (ns) Turn-On Rise Time (ns) Figure A. Turn-On Rise Time vs.temperature Figure A. Turn-On Rise Time vs.temperature Turn-On Rise Time (ns) Turn-On Rise Time (ns) Figure B. Turn-On Rise Time Figure B. Turn-On Rise Time Turn-Off Fall Time (ns) Turn-Off Fall Time (ns) Figure 7A. Turn-Off Fall Time vs. Temperature Figure 7A. Turn-Off Fall Time vs. Temperature
5 Turn-Off Fall Time (ns) Turn-Off Fall Time (ns) Figure 7B. Turn-Off Fall Time vs. Input voltage Figure 7B. Turn-Off Fall Time vs. Input voltage Figure 8A. Logic "" Input Voltage vs. Temperature Figure 8A. Logic "" Input Voltage vs. Temperature V BAIS Figure 8B. Logic "" Input Voltage V BAIS Figure 8B. Logic "" Input Voltage
6 High Level Output Voltage (V) High Level Output Voltage (V) Figure A. High Level Output Voltage vs. Temperature (Io = ma) Figure A. High Level Output Voltage vs. Temperature (Io = ma) High Level Output Voltage (V) High Level Output Voltage (V) V BAIS V BAIS Figure B. High Level Output Voltage (Io = ma) Figure B. High Level Output Voltage (Io = ma) Low Level Output Voltage (V) Figure A. Low Level Output Voltage vs.temperature (Io = ma) Low Level Output Voltage (V) Figure A. Low Level Output Voltage vs.temperature (Io = ma)
7 Low Level Output Voltage (V)..... Figure B. Low Level Output (Io = ma) Low Level Output Voltage (V) Figure B. Low Level Output (Io = ma) Output Source Current (ma) Output Source Current (ma) Figure 9A. Output Source Current vs. Temperature Figure 9A. Output Source Current vs. Temperature Output Source Current (ma) Output Source Current (ma) Figure 9B. Output Source Current Figure 9B. Output Source Current 7
8 8 Output Sink Current (ma) Output Sink Current (ma) Figure A. Output Sink Current vs.temperature Figure A. Output Sink Current vs.temperature 9 Output Sink Current (ma) Output Sink Current (ma) 7 Figure B. Output Sink Current Figure B. Output Sink Current Summary As shown by this document, the IRS and the IR are very similar with only a few parametric differences. 8
Application Note AN-1114
Application Note AN- IRS and IR Comparison By Jason Nguyen, Min Fang, David New Table of Contents Page Introduction... Block Diagrams... Electrical Characteristic Differences... Figures... Summary...9
Application Note AN-1125
Application Note AN- IRS(7,8,7) and IR(7,8,7) Comparison By Jason Nguyen, Fang, David New Table of Contents Page Introduction... Block Diagram... Electrical Characteristic Differences... Figures... Summary...
HIGH AND LOW SIDE DRIVER
Data Sheet No. PD-O Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
IR2122(S) CURRENT SENSING SINGLE CHANNEL DRIVER
Preliminary Data Sheet No. PD60130-K CURRENT SENSING SINGLE CHANNEL DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt
V OFFSET. Description
Features n Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
IR2304(S) & (PbF) HALF-BRIDGE DRIVER Product Summary
Data Sheet No. PD60200 revb Features Floating channel designed for bootstrap operation to +600V. Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Under voltage
Not recommended for new designs. No replacement is available
Aug 2, 28 IRS218S SINGLE HIGH SIDE DRIVER IC IC Features Gate drive supply range from 1 V to 2 V Undervoltage lockout for V BS and V CC 3.3 V and V input logic compatible Tolerant to negative transient
IR2105 HALF BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection
Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to 2V Undervoltage lockout V Schmitt-triggered
VCC 5 OUT 4. Orderable Part Number Form Quantity IR44272LPBF SOT23-5 Tape and Reel 3000 IR44272LTRPBF
HVIC TM Features Wide VCC range (5V to 20V) CMOS Schmitt-triggered inputs Under voltage lockout 3.3V logic compatible Enable input Output in phase with inputs Leadfree, RoHS compliant SOT-23 Gate Driver
Standard Pack Form Quantity
Dual Low Side Driver Features Product Summary Gate drive supply range from 6V to 20V CMOS Schmitt-triggered inputs Matched propagation delay for both channels Outputs in phase with inputs I O+/- 1.5A /
IRS2103(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection. 600 V max. 130 ma/270 ma 10 V - 20 V V OFFSET
Data Sheet No. PD6263 Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage
V OFFSET V OUT. Package V B V S
Features Gate drive supply range from V to V Undervoltage lockout for V BS and V CC. V and V input logic compatible Tolerant to negative transient voltage Matched propagation delays for all channels RoHS
Packages. Input logic. Part HIN/LIN yes
Data Sheet No. PD60209 revc Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to
200V HO V DD V B HIN SD HIN SD V S TO LOAD LIN V CC V SS LIN COM LO
Data Sheet No. PD6195-E Features Floating channel designed for bootstrap operation Fully operational to Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 to V Undervoltage
High and Low Side Driver
High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range
IR4426/IR4427/IR4428(S) & (PbF) DUAL LOW SIDE DRIVER
Data Sheet No. PD60177 Rev. F Features Gate drive supply range from 6 to 20V CMOS Schmitt-triggered inputs Matched propagation delay for both channels Outputs out of phase with inputs (IR4426) Outputs
HIGH AND LOW SIDE DRIVER. Product Summary VOFFSET VOUT. Description
Features n Floating channel designed for bootstrap operation Fully operational to +4V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
HVIC TM. Single Low-Side Driver IC IRS44273LPBF. Product Summary
PBF HVIC TM Features CMOS Schmitt-triggered inputs Under voltage lockout 3.3V logic compatible Output in phase with input Leadfree, RoHS compliant Typical Applications General Purpose Gate Driver DC-DC
Half-Bridge Driver IR25606SPBF. Features. Product Summary. Description. Package Options. Ordering Information
Half-Bridge Driver Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Undervoltage
IRS2117/IRS2118(S)PbF
Data Sheet No. PD227 IRS2117/IRS211(S)PbF Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
IRS2113MPBF HIGH- AND LOW-SIDE DRIVER
February 8, 2012 IRS2113MPBF HIGH- AND LOW-SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage dv/dt immune Gate drive
Packages. Crossconduction. Input logic. Part. prevention logic COM HIN/LIN no none 21814
Data Sheet No. PD014-D Features Floating channel designed for bootstrap operation Fully operational to +00V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Undervoltage
High and Low Side Driver
High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to 200V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
IRS2104(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET. 600 V max. 130 ma/270 ma 10 V - 20 V
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout. V, V,
IRS2181/IRS21814(S)PbF
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout for both
IR2112(S) HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET. 600V max. 200 ma / 420 ma 10-20V
Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both
IR2110 HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages. Description. Typical Connection. 500V max. V OFFSET 10-20V VOUT.
Features n Floating channel designed for bootstrap operation Fully operational to +5V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
High and Low Side Driver
High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to +1200 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range
IRS21844MPBF HALF-BRIDGE DRIVER
November 19, 2010 HALF-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to + 600 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
V OFFSET. Packages. 14-Lead PDIP
Preliminary Data Sheet No. PD63 rev.p Features Floating channel designed for bootstrap operation Fully operational to +12V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from
IRS2110(-1,-2,S)PbF IRS2113(-1,-2,S)PbF HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages
Features Floating channel designed for bootstrap operation Fully operational to +5 V or +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage lockout
IRS2184/IRS21844(S)PbF
Data Sheet No. PD Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage
IRS4426/IRS4427/IRS4428 DUAL LOW SIDE DRIVER
February 28, 2011 Datasheet No 97481 IRS4426/IRS4427/IRS4428 DUAL LOW SIDE DRIVER Features Gate drive supply range from 6 V to 20 V CMOS Schmitt-triggered inputs 3.3V and 5V logic compatible Two independent
IRS212(7, 71, 8, 81)(S)PbF
CURRENT SENSG SGLE CHANNEL DRIVER Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage dv/dt immune Application-specific gate drive
V OFFSET 600V max. I O +/- 130 ma / 270 ma V OUT. Packages
Data Sheet No. PD-S Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to 2V Undervoltage
IR2112(S) & (PbF) HIGH AND LOW SIDE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both
IR2106/IR21064 IR2107/IR21074 HIGH AND LOW SIDE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +00V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 0 to 0V Undervoltage lockout for both
Packages. Feature Comparison. Crossconduction. Input logic. Part COM HIN/LIN no none 21064
DS No.PD6266 Rev A Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage
IRS2183/IRS21834(S)PbF
Data Sheet No. PD Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage
RADIATION HARDENED HIGH AND LOW SIDE GATE DRIVER Product Summary. Description
Features RADIATION HARDENED HIGH AND W SIDE GATE DRIER Product Summary n Total dose capability to 100 krads(si) n Floating channel designed for bootstrap operation n Fully operational to +400 n Tolerant
IR2302(S) & (PbF) HALF-BRIDGE DRIVER. Packages
Data Sheet No. PD7 Rev.A Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
RADIATION HARDENED HIGH AND LOW SIDE GATE DRIVER
Features RADIATION HARDENED HIGH AND W SIDE GATE DRIER n Total dose capability to 100 krads(si) n Floating channel designed for bootstrap operation n Fully operational to +400 n Tolerant to negative transient
3-PHASE BRIDGE DRIVER
Data Sheet No. PD-6.33E IR2132 Features n Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1
HIGH VOLTAGE HALF BRIDGE
Preliminary Data Sheet No. PD0-D IR0HDC0U-P HIGH LTAGE HALF BRIDGE Features Output Power IGBT s in half-bridge configuration 55V rated breakdown voltage High side gate drive designed for bootstrap operation
IRS211(7,71,8)(S) SINGLE CHANNEL DRIVER
February 18, 29 SINGLE CHANNEL DRIVER IC Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
IRS21956S Floating Input, High and Low(Dual mode) Side Driver
January 16, 2009 Datasheet No. - PD97375 IRS21956S Floating Input, High and Low(Dual mode) Side Driver Features Low side programmable ramp gate drive Low side generic gate drive integrated using the same
Automotive Grade AUIRS212(71,81) June 12 th, Over Current Protected Single Channel Driver. Product Summary
June 12 th, 2012 Automotive Grade AUIRS212(7,71,8,81)S Over Current Protected Single Channel Driver Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative
Automotive Grade AUIRS4426S DUAL LOW SIDE DRIVER
March 19 th, 2010 Automotive Grade AUIRS4426S DUAL LOW SIDE DRIVER Features Gate drive supply range from 6 V to 20 V CMOS Schmitt-triggered inputs Matched propagation delay for both channels Outputs out
Automotive Grade AUIRS2301S HIGH AND LOW SIDE DRIVER
January 14, 2011 Automotive Grade AUIRS2301S HIGH AND LOW SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt
Automotive Grade AUIRS2112S HIGH- AND LOW-SIDE DRIVER
August 29 th, 211 Automotive Grade AUIRS2112S HIGH- AND LOW-SIDE DRIVER Features Drives IGBT/MOSFET power devices Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to
Automotive Grade AUIRS211(0,3)S HIGH- AND LOW-SIDE DRIVER
Dec. 13, 2009 Automotive Grade AUIRS211(0,3)S HIGH- AND LOW-SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +500 V or +600 V Tolerant to negative transient voltage
IRS21867S HIGH AND LOW SIDE DRIVER
31 May, 2011 IRS21867S HIGH AND LOW SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage, dv/dt immune Low VCC operation
HIGH VOLTAGE HALF BRIDGE
Preliminary Data Sheet No. PD0-C IR0HDC0U-P HIGH LTAGE HALF BRIDGE Features Output Power IGBT s in half-bridge configuration 00V rated breakdown voltage High side gate drive designed for bootstrap operation
Automotive Grade AUIRS21811S HIGH AND LOW SIDE DRIVER
July 28 th, 2010 Automotive Grade AUIRS21811S HIGH AND LOW SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage, dv/dt
IR20153S & (PbF) HIGH SIDE DRIVER WITH RECHARGE
Preliminary Data Sheet PD60214 Rev B Features Floating channel designed for bootstrap operation Fully operational up to 150V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
TF2103. Half-Bridge Gate Driver. Description. Features. Applications. Ordering Information. Typical Application. Advance Info.
Features Floating high-side driver in bootstrap operation to 600V Drives two N-channel MOSFETs or IGBTs in a half bridge configuration 290mA source/600ma sink output current capability Outputs tolerant
IRS2130D/IRS21303D/IRS2132D
Data Sheet No. PD6256 reva IRS213D/IRS2133D/IRS2132D 3-PHASE BRIDGE DRIER Features Floating channel designed for bootstrap operation Fully operational to +6 Tolerant to negative transient voltage, d/dt
100V VCC VB 6 IRS10752 HO 5 VS 4. To Load. IRS10752LPBF SOT-23-6L Tape and Reel 3000 IRS10752LTRPBF
HVIC TM Features SOT-23 High-Side Gate Driver IC Description Floating gate driver designed for bootstrap operation Fully operational to +100 V Excellent dv/dt immunity Excellent negative V S transient
IX2127NTR. High-Voltage Power MOSFET & IGBT Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features.
High-Voltage Power MOSFET & IGBT Driver Driver Characteristics Parameter Rating Units V OFFSET 6 V I O +/- (Source/Sink) 25/5 ma V th 25 mv t ON / t OFF (Typical) 1 ns Features Floating Channel Designed
FAN7391 High-Current, High & Low-Side, Gate-Drive IC
FAN7391 High-Current, High & Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 4.5 A / 4.5 A Sourcing / Sinking Current Driving Capability Common-Mode dv/dt Noise-Canceling
Typical Application Circuit V CC HIN,, LIN,, FAULT EN GND Pin Description V CC HIN,, LIN,, FAULT EN RCIN ITRIP V SS PIN NO. PIN NAME PIN FUNCTION V B,
SOIC8 -Phase Bridge Driver General Description The is a high voltage, high speed power MOSFET and IGBT drivers with a three independent high and low side referenced output channels for -phase applications.
3-PHASE BRIDGE DRIVER
Features Floating channel designed for bootstrap operation. Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V (IRS2136D/ IRS21368D),11.5
ADVANCE INFO TF Half -Bridge Driver. Features. Description. Applications. Ordering Information. Typical Application ADVANCE INFO.
Half -Bridge Driver Features Floating high-side driver in bootstrap operation to 600V Drives two N-channel MOSFETs or IGBTs in a half bridge configuration Outputs tolerant to negative transients Programmable
IRS2136/IRS21362/IRS21363/IRS21365/ IRS21366/IRS21367/IRS21368 (J&S) PbF 3-PHASE BRIDGE DRIVER
Data Sheet No. PD6272 IRS2136/IRS21362/IRS21363/IRS21365/ IRS21366/IRS21367/IRS21368 (J&S) PbF 3-PHASE BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V
HALF-BRIDGE DRIVER. Features. Packages. Product Summary
June 1, 211 HALF-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 V
FAN73901 High- and Low-Side, Gate-Drive IC
FAN7391 High- and Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 2.5 A / 2.5 A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling
Pin Definition: 1. VCC 8. VB 2. RT 7. HO 3. CT 6. VS 4. COMP 5. LO
DIP-8 SOP-8 Pin Definition: 1. VCC 8. VB 2. RT 7. HO 3. CT 6. VS 4. COMP 5. LO Description is a high voltage, high speed, self-oscillating power MOSFET and IGBT driver with both high and low side referenced
QS54/74FCT373T, 2373T. High-Speed CMOS Bus Interface 8-Bit Latches MDSL QUALITY SEMICONDUCTOR, INC. 1 DECEMBER 28, 1998
Q QUALITY SEMICONDUCTOR, INC. QS54/74FCT373T, 2373T High-Speed CMOS Bus Interface 8-Bit Latches QS54/74FCT373T QS54/74FCT2373T FEATURES/BENEFITS Pin and function compatible to the 74F373 74FCT373 and 74ABT373
IX2127NTR. High-Voltage Power MOSFET & IGBT Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features.
High-Voltage Power MOSFET & IGBT Driver Driver Characteristics Parameter Rating Units V OFFSET 6 V I O +/- (Source/Sink) 25/5 ma V th 25 mv t ON / t OFF (Typical) 1 ns Features Floating Channel Designed
IRS SOT-23 High-Side Gate Driver IC IRS10752LPBF. Features. Description. Package Options. Applications. Typical Connection Diagram
µhvic TM Features SOT-23 High-Side Gate Driver IC Description Floating gate driver designed for bootstrap operation Fully operational to +100 V Excellent dv/dt immunity Excellent negative V S transient
FAN7191-F085 High-Current, High and Low Side Gate Drive IC
FAN7191-F85 High-Current, High and Low Side Gate Drive IC Features! Floating Channel for Bootstrap Operation to +6V! 4.5A Sourcing and 4.5A Sinking Current Driving Capability! Common-Mode dv/dt Noise Cancelling
FAN7371 High-Current High-Side Gate Drive IC
FAN1 High-Current High-Side Gate Drive IC Features! Floating Channel for Bootstrap Operation to +V! A/A Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling Circuit!.V and V Input
IXD611S1 IXD611S7. 600V, 600 ma High & Low-side Driver for N-Channel MOSFETs and IGBTs. Features. General Description
IXD V, ma High & Low-side Driver for N-Channel MOSFETs and IGBTs IXD Features Floating High Side Driver with boot-strap Power supply along with a Low Side Driver. Fully operational to V ± V/ns dv/dt immunity
ELECTRONIC GIANT. EG3013 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG33 Datasheet Copyright 22 by EGmicro Corporation REV. EG33 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
ELECTRONIC GIANT. EG3012 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG32 Datasheet Copyright 22 by EGmicro Corporation REV. EG32 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
SELF-OSCILLATING HALF-BRIDGE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +600V olerant to negative transient voltage dv/dt immune Undervoltage lockout Programmable oscillator frequency 1 f = 1.4
IX2113BTR. 600V High and Low Side Gate Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features. Ordering Information
V High and Low Side Gate Driver Driver Characteristics Parameter Rating Units V OFFSET V I O +/- (Source/Sink) / A V OUT - V t on /t off / ns Delay Matching (Max) ns Features Floating Channel for Bootstrap
FAN7361, FAN7362 High-Side Gate Driver
FAN7361, FAN7362 High-Side Gate Driver Features! Floating Channel Designed for Bootstrap Operation to +600V! Typically 250mA/500mA Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling
NTE4055B and NTE4056B Integrated Circuit CMOS, BCD to 7 Segment Decoder/Drivers
NTE4055B and NTE4056B Integrated Circuit CMOS, BCD to 7 Segment Decoder/Drivers Description: The NTE4055B ( Display Frequency Output) and NTE4056B (Strobed Latch Function) are single digit BCD to 7 segment
IR2153Z PD SELF-OSCILLATING HALF-BRIDGE DRIVER. Features. Product Summary
Features Floating channel designed for bootstrap operation Fully operational to +600 Tolerant to negative transient voltage d/dt immune Undervoltage lockout Programmable oscillator frequency 1 f = 1.4
DS1040 Programmable One-Shot Pulse Generator
www.dalsemi.com FEATURES All-silicon pulse width generator Five programmable widths Equal and unequal increments available Pulse widths from 5 ns to 500 ns Widths are stable and precise Rising edge-triggered
IR3101 Series 1.6A, 500V
Half-Bridge FredFet and Integrated Driver Features Output power FredFets in half-bridge configuration High side gate drive designed for bootstrap operation Bootstrap diode integrated into package. Lower
IR2153/IR2153D SELF-OSCILLATING HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connections
Features Floating channel designed for bootstrap operation Fully operational to 600V Tolerant to negative transient voltage dv/dt immune Undervoltage lockout Programmable oscillator frequency 1 f = 1.4
DS1021 Programmable 8-Bit Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay Models with 0.25 ns and 0.5 ns steps Programmable using 3-wire serial port or 8- bit parallel port Leading and trailing edge accuracy Economical Auto-insertable,
Unit 1 Session - 3 TTL Parameters
Objectives Understanding various TTL Parameters Floating Inputs Worst-Case Input Voltages & Output Voltages Profiles and Windows Compatibility Sourcing and Sinking Noise Immunity Standard Loading and Loading
CMOS Serial Digital Pulse Width Modulator INPUT CLK MODULATOR LOGIC PWM 8 STAGE RIPPLE COUNTER RESET LOAD FREQUENCY DATA REGISTER
css Custom Silicon Solutions, Inc. S68HC68W1 April 2003 CMOS Serial Digital Pulse Width Modulator Features Direct Replacement for Intersil CDP68HC68W1 Pinout (PDIP) TOP VIEW Programmable Frequency and
DS in-1 Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay 3 independent buffered delays Delay tolerance ±2ns for -10 through 60 Stable and precise over temperature and voltage range Leading and trailing edge accuracy
ELECTRONIC GIANT. EG3113 Datasheet. Half-Bridge Driver. Copyright 2017 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG33 Datasheet Copyright 27 by EGmicro Corporation REV. EG33 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
High-Current, High & Low-Side, Gate-Drive IC
FAN739 High-Current, High & Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6V Typically 4.5A/4.5A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling
NTE40192B & NTE40193B Integrated Circuit CMOS, Presettable Up/Down Counters (Dual Clock with Reset)
NTE40192B & NTE40193B Integrated Circuit CMOS, Presettable Up/Down Counters (Dual Clock with Reset) Description: The NTE40192B (BCD Type), and NTE40193B (Binary Type) are presettable up/down counters in
Package. Figure1. Typical Application Resonant Converter (LLC type)
General Description The PN7106A/B is a high voltage, high speed power MOSFET and IGBT driver based on P_SUB P_EPI process. The floating channel driver can be used to drive two N-channel power MOSFET or
FAN7392 High-Current, High- and Low-Side, Gate-Drive IC
FAN7392 High-Current, High- and Low-Side, Gate-Drive IC Features Floating Channel for Bootstrap Operation to +6V 3A/3A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling Circuit
MIC4421/4422. Bipolar/CMOS/DMOS Process. General Description. Features. Applications. Functional Diagram. 9A-Peak Low-Side MOSFET Driver
9A-Peak Low-Side MOSFET Driver Micrel Bipolar/CMOS/DMOS Process General Description MIC4421 and MIC4422 MOSFET drivers are rugged, efficient, and easy to use. The MIC4421 is an inverting driver, while
DS Tap Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay 5 taps equally spaced Delay tolerance ±2 ns or ±3%, whichever is greater Stable and precise over temperature and voltage range Leading and trailing edge
DS Tap High Speed Silicon Delay Line
www.dalsemi.com FEATURES All-silicon timing circuit Five delayed clock phases per input Precise tap-to-tap nominal delay tolerances of ±0.75 and ±1 ns Input-to-tap 1 delay of 5 ns Nominal Delay tolerances
NTE74HC40105 Integrated Circuit TTL High Speed CMOS, 4 Bit x 16 Word FIFO Register
NTE74HC40105 Integrated Circuit TTL High Speed CMOS, 4 Bit x 16 Word FIFO Register Description: The NTE74HC40105 is a high speed silicon gate CMOS device in a 16 Lead DIP type package that is compatible,
IX2120BTR. 1200V High and Low Side Gate Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features. Ordering Information
IX High and Low Side Gate Driver Driver Characteristics Parameter Rating Units OFFSET I O +/- (Source/Sink) / A OUT - t on /t off / ns Features Floating Channel for Bootstrap Operation to + Outputs Capable
DS in 1 High Speed Silicon Delay Line FEATURES PIN ASSIGNMENT
DS1044 4 in 1 High Speed Silicon Delay Line FEATURES All silicon timing circuit Four independent buffered delays Initial delay tolerance ±1.5 ns Stable and precise over temperature and voltage Leading
Basic Characteristics of Digital ICs
ECEN202 Section 2 Characteristics of Digital IC s Part 1: Specification of characteristics An introductory look at digital IC s: Logic families Basic construction and operation Operating characteristics
8K x 8 Static RAM CY6264. Features. Functional Description
8K x 8 Static RAM Features 55, 70 ns access times CMOS for optimum speed/power Easy memory expansion with CE 1, CE 2, and OE features TTL-compatible inputs and outputs Automatic power-down when deselected