Application Note AN-1114
|
|
|
- George Scott
- 5 years ago
- Views:
Transcription
1 Application Note AN- IRS and IR Comparison By Jason Nguyen, Min Fang, David New Table of Contents Page Introduction... Block Diagrams... Electrical Characteristic Differences... Figures... Summary...9 Introduction The IRS is a new HVIC product that replaces the IR HVICs and is pin-to-pin compatible with its corresponding predecessor. In many cases, little or no change is necessary to use the new products. This application note describes the various differences between the IRS and the IR HVICs. The IRS is a high voltage, high speed power MOSFET and IGBT drivers with independent high and low side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS or LSTTL output, down to. V logic. The output driver features a high pulse current buffer stage designed for minimum driver crossconduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to V.
2 Block Diagrams The IRS and IR share the same block diagram. There are no functional changes between corresponding part numbers. Electrical Characteristic Differences All measurement conditions remain unchanged unless noted. Parameters not mentioned in this document have not changed. Absolute imum Ratings There are no changes in the Absolute imum Ratings. Recommended Operating Conditions There are no changes in the Recommended Operating Conditions.
3 Dynamic Electrical Characteristics Parameter IR IRS Symbol Definition typ max typ max t r Turn-on rise time (Vs = V) t f Turn-off fall time (Vs = V) 8 8 Units ns The IRS has faster rise and fall times when compared to the IR. Static Electrical Characteristics Parameter IR IRS Symbol Definition min typ max min typ max V IH Logic "" input voltage V IL Logic "" input voltage V SD,TH+!SD input positive going threshold V SD,TH-!SD input negative going threshold V OH High level output voltage, - V O Io = ma Io = ma V OL Low level output voltage, V O Io = ma Io = ma I O+ Output high short circuit pulsed current (V O = V, VIN=Logic "", PW <= us) I O- Output low short circuit pulsed current (V O = V, VIN = Logic "", PW <= us) - - Units V ma With the IRS,. The V IH and V SD,TH+ has been reduced to. V for better. V logic compatibility.. The V OH and V OL are tested using a new standardized test condition of I O = ma. The output driver s on resistance is slightly lower for IRS.. The typical values for I O+ and I O- are marginally higher, which allows faster switching. Figures This figures shown in this section compare figures shown in the IR (left column) and IRS (right column) datasheets. Illustrations that have not changed between the two datasheets have not been included in this section.
4 IR IRS Turn-On Rise Time (ns) Turn-On Rise Time (ns) Figure 9A. Turn-On Rise Time vs.temperature Figure 9A. Turn-On Rise Time vs.temperature Turn-On Rise Time (ns) Turn-On Rise Time (ns) Figure 9B. Turn-On Rise Time Figure 9B. Turn-On Rise Time Turn-Off Fall Time (ns) Turn-Off Fall Time (ns) Figure A. Turn-Off Fall Time vs. Temperature Figure A. Turn-Off Fall Time vs. Temperature
5 Turn-Off Fall Time (ns) Turn-Off Fall Time (ns) Figure B. Turn-Off Fall Time vs. Input voltage Figure B. Turn-Off Fall Time vs. Input voltage Figure A. Logic "" Input Voltage vs. Temperature Figure A. Logic "" Input Voltage vs. Temperature V BAIS Figure B. Logic "" Input Voltage V BAIS Figure B. Logic "" Input Voltage
6 SD Input Positive Going threshold (V) SD Input Positive Going threshold (V) Figure A. SD Input Positive Going Threshold vs. Temperature Figure A. SD Input Positive Going Threshold vs. Temperature SD Input Positive Going threshold (V) SD Input Positive Going threshold (V) V CC V CC Figure B. SD Input Positive Going Threshold vs. Supply Figure B. SD Input Positive Going Threshold vs. Supply High Level Output Voltage (V) High Level Output Voltage (V) Figure A. High Level Output Voltage vs. Temperature (Io = ma) Figure A. High Level Output Voltage vs. Temperature (Io = ma)
7 High Level Output Voltage (V) High Level Output Voltage (V) V BAIS V BAIS Figure B. High Level Output Voltage (Io = ma) Figure B. High Level Output Voltage (Io = ma) Low Level Output Voltage (V) Figure 7A. Low Level Output Voltage vs.temperature (Io = ma) Low Level Output Voltage (V) Figure 7A. Low Level Output Voltage vs.temperature (Io = ma) Low Level Output Voltage (V).. Figure 7B. Low Level Output (Io = ma) Low Level Output Voltage (V)..... Figure 7B. Low Level Output (Io = ma) 7
8 Output Source Current (ma) Output Source Current (ma) Figure A. Output Source Current vs. Temperature Figure A. Output Source Current vs. Temperature Output Source Current (ma) Output Source Current (ma) Figure B. Output Source Current Figure B. Output Source Current 8 Output Sink Current (ma) Output Sink Current (ma) Figure A. Output Sink Current vs.temperature Figure A. Output Sink Current vs.temperature 8
9 9 Output Sink Current (ma) Output Sink Current (ma) 7 Figure B. Output Sink Current Figure B. Output Sink Current Summary As shown by this document, the IRS and the IR are very similar with only a few parametric differences. 9
Application Note AN-1113
Application Note AN- IRS and IR Comparison By Jason Nguyen, Min Fang, David New Table of Contents Page Introduction... Block Diagrams... Electrical Characteristic Differences... Figures... Summary...8
Application Note AN-1125
Application Note AN- IRS(7,8,7) and IR(7,8,7) Comparison By Jason Nguyen, Fang, David New Table of Contents Page Introduction... Block Diagram... Electrical Characteristic Differences... Figures... Summary...
HIGH AND LOW SIDE DRIVER
Data Sheet No. PD-O Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
V OFFSET. Description
Features n Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
IR2122(S) CURRENT SENSING SINGLE CHANNEL DRIVER
Preliminary Data Sheet No. PD60130-K CURRENT SENSING SINGLE CHANNEL DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt
IR2304(S) & (PbF) HALF-BRIDGE DRIVER Product Summary
Data Sheet No. PD60200 revb Features Floating channel designed for bootstrap operation to +600V. Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Under voltage
IRS21844MPBF HALF-BRIDGE DRIVER
November 19, 2010 HALF-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to + 600 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
Not recommended for new designs. No replacement is available
Aug 2, 28 IRS218S SINGLE HIGH SIDE DRIVER IC IC Features Gate drive supply range from 1 V to 2 V Undervoltage lockout for V BS and V CC 3.3 V and V input logic compatible Tolerant to negative transient
IR2105 HALF BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection
Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to 2V Undervoltage lockout V Schmitt-triggered
VCC 5 OUT 4. Orderable Part Number Form Quantity IR44272LPBF SOT23-5 Tape and Reel 3000 IR44272LTRPBF
HVIC TM Features Wide VCC range (5V to 20V) CMOS Schmitt-triggered inputs Under voltage lockout 3.3V logic compatible Enable input Output in phase with inputs Leadfree, RoHS compliant SOT-23 Gate Driver
200V HO V DD V B HIN SD HIN SD V S TO LOAD LIN V CC V SS LIN COM LO
Data Sheet No. PD6195-E Features Floating channel designed for bootstrap operation Fully operational to Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 to V Undervoltage
HIGH AND LOW SIDE DRIVER. Product Summary VOFFSET VOUT. Description
Features n Floating channel designed for bootstrap operation Fully operational to +4V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
IRS2103(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection. 600 V max. 130 ma/270 ma 10 V - 20 V V OFFSET
Data Sheet No. PD6263 Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage
IRS2113MPBF HIGH- AND LOW-SIDE DRIVER
February 8, 2012 IRS2113MPBF HIGH- AND LOW-SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage dv/dt immune Gate drive
V OFFSET V OUT. Package V B V S
Features Gate drive supply range from V to V Undervoltage lockout for V BS and V CC. V and V input logic compatible Tolerant to negative transient voltage Matched propagation delays for all channels RoHS
IR2112(S) HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET. 600V max. 200 ma / 420 ma 10-20V
Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both
IR2110 HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages. Description. Typical Connection. 500V max. V OFFSET 10-20V VOUT.
Features n Floating channel designed for bootstrap operation Fully operational to +5V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
IRS2104(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET. 600 V max. 130 ma/270 ma 10 V - 20 V
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout. V, V,
Standard Pack Form Quantity
Dual Low Side Driver Features Product Summary Gate drive supply range from 6V to 20V CMOS Schmitt-triggered inputs Matched propagation delay for both channels Outputs in phase with inputs I O+/- 1.5A /
HVIC TM. Single Low-Side Driver IC IRS44273LPBF. Product Summary
PBF HVIC TM Features CMOS Schmitt-triggered inputs Under voltage lockout 3.3V logic compatible Output in phase with input Leadfree, RoHS compliant Typical Applications General Purpose Gate Driver DC-DC
High and Low Side Driver
High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range
High and Low Side Driver
High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to +1200 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range
Half-Bridge Driver IR25606SPBF. Features. Product Summary. Description. Package Options. Ordering Information
Half-Bridge Driver Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Undervoltage
IRS2184/IRS21844(S)PbF
Data Sheet No. PD Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage
High and Low Side Driver
High and Low Side Driver Features Product Summary Floating channel designed for bootstrap operation Fully operational to 200V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
IRS2117/IRS2118(S)PbF
Data Sheet No. PD227 IRS2117/IRS211(S)PbF Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
V OFFSET. Packages. 14-Lead PDIP
Preliminary Data Sheet No. PD63 rev.p Features Floating channel designed for bootstrap operation Fully operational to +12V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from
Packages. Crossconduction. Input logic. Part. prevention logic COM HIN/LIN no none 21814
Data Sheet No. PD014-D Features Floating channel designed for bootstrap operation Fully operational to +00V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Undervoltage
Packages. Input logic. Part HIN/LIN yes
Data Sheet No. PD60209 revc Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to
IR2302(S) & (PbF) HALF-BRIDGE DRIVER. Packages
Data Sheet No. PD7 Rev.A Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
IRS2110(-1,-2,S)PbF IRS2113(-1,-2,S)PbF HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages
Features Floating channel designed for bootstrap operation Fully operational to +5 V or +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage lockout
V OFFSET 600V max. I O +/- 130 ma / 270 ma V OUT. Packages
Data Sheet No. PD-S Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to 2V Undervoltage
IR2112(S) & (PbF) HIGH AND LOW SIDE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both
IRS2181/IRS21814(S)PbF
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout for both
IR4426/IR4427/IR4428(S) & (PbF) DUAL LOW SIDE DRIVER
Data Sheet No. PD60177 Rev. F Features Gate drive supply range from 6 to 20V CMOS Schmitt-triggered inputs Matched propagation delay for both channels Outputs out of phase with inputs (IR4426) Outputs
RADIATION HARDENED HIGH AND LOW SIDE GATE DRIVER Product Summary. Description
Features RADIATION HARDENED HIGH AND W SIDE GATE DRIER Product Summary n Total dose capability to 100 krads(si) n Floating channel designed for bootstrap operation n Fully operational to +400 n Tolerant
IRS4426/IRS4427/IRS4428 DUAL LOW SIDE DRIVER
February 28, 2011 Datasheet No 97481 IRS4426/IRS4427/IRS4428 DUAL LOW SIDE DRIVER Features Gate drive supply range from 6 V to 20 V CMOS Schmitt-triggered inputs 3.3V and 5V logic compatible Two independent
Packages. Feature Comparison. Crossconduction. Input logic. Part COM HIN/LIN no none 21064
DS No.PD6266 Rev A Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage
IRS212(7, 71, 8, 81)(S)PbF
CURRENT SENSG SGLE CHANNEL DRIVER Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage dv/dt immune Application-specific gate drive
RADIATION HARDENED HIGH AND LOW SIDE GATE DRIVER
Features RADIATION HARDENED HIGH AND W SIDE GATE DRIER n Total dose capability to 100 krads(si) n Floating channel designed for bootstrap operation n Fully operational to +400 n Tolerant to negative transient
IR2106/IR21064 IR2107/IR21074 HIGH AND LOW SIDE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +00V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 0 to 0V Undervoltage lockout for both
IRS2183/IRS21834(S)PbF
Data Sheet No. PD Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage
3-PHASE BRIDGE DRIVER
Data Sheet No. PD-6.33E IR2132 Features n Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1
HIGH VOLTAGE HALF BRIDGE
Preliminary Data Sheet No. PD0-D IR0HDC0U-P HIGH LTAGE HALF BRIDGE Features Output Power IGBT s in half-bridge configuration 55V rated breakdown voltage High side gate drive designed for bootstrap operation
IRS211(7,71,8)(S) SINGLE CHANNEL DRIVER
February 18, 29 SINGLE CHANNEL DRIVER IC Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
IRS21956S Floating Input, High and Low(Dual mode) Side Driver
January 16, 2009 Datasheet No. - PD97375 IRS21956S Floating Input, High and Low(Dual mode) Side Driver Features Low side programmable ramp gate drive Low side generic gate drive integrated using the same
Automotive Grade AUIRS212(71,81) June 12 th, Over Current Protected Single Channel Driver. Product Summary
June 12 th, 2012 Automotive Grade AUIRS212(7,71,8,81)S Over Current Protected Single Channel Driver Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative
Automotive Grade AUIRS2112S HIGH- AND LOW-SIDE DRIVER
August 29 th, 211 Automotive Grade AUIRS2112S HIGH- AND LOW-SIDE DRIVER Features Drives IGBT/MOSFET power devices Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to
Automotive Grade AUIRS211(0,3)S HIGH- AND LOW-SIDE DRIVER
Dec. 13, 2009 Automotive Grade AUIRS211(0,3)S HIGH- AND LOW-SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +500 V or +600 V Tolerant to negative transient voltage
Automotive Grade AUIRS2301S HIGH AND LOW SIDE DRIVER
January 14, 2011 Automotive Grade AUIRS2301S HIGH AND LOW SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt
HIGH VOLTAGE HALF BRIDGE
Preliminary Data Sheet No. PD0-C IR0HDC0U-P HIGH LTAGE HALF BRIDGE Features Output Power IGBT s in half-bridge configuration 00V rated breakdown voltage High side gate drive designed for bootstrap operation
IRS21867S HIGH AND LOW SIDE DRIVER
31 May, 2011 IRS21867S HIGH AND LOW SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage, dv/dt immune Low VCC operation
IR20153S & (PbF) HIGH SIDE DRIVER WITH RECHARGE
Preliminary Data Sheet PD60214 Rev B Features Floating channel designed for bootstrap operation Fully operational up to 150V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
Automotive Grade AUIRS21811S HIGH AND LOW SIDE DRIVER
July 28 th, 2010 Automotive Grade AUIRS21811S HIGH AND LOW SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage, dv/dt
Automotive Grade AUIRS4426S DUAL LOW SIDE DRIVER
March 19 th, 2010 Automotive Grade AUIRS4426S DUAL LOW SIDE DRIVER Features Gate drive supply range from 6 V to 20 V CMOS Schmitt-triggered inputs Matched propagation delay for both channels Outputs out
3-PHASE BRIDGE DRIVER
Features Floating channel designed for bootstrap operation. Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V (IRS2136D/ IRS21368D),11.5
IRS2130D/IRS21303D/IRS2132D
Data Sheet No. PD6256 reva IRS213D/IRS2133D/IRS2132D 3-PHASE BRIDGE DRIER Features Floating channel designed for bootstrap operation Fully operational to +6 Tolerant to negative transient voltage, d/dt
Pin Definition: 1. VCC 8. VB 2. RT 7. HO 3. CT 6. VS 4. COMP 5. LO
DIP-8 SOP-8 Pin Definition: 1. VCC 8. VB 2. RT 7. HO 3. CT 6. VS 4. COMP 5. LO Description is a high voltage, high speed, self-oscillating power MOSFET and IGBT driver with both high and low side referenced
Typical Application Circuit V CC HIN,, LIN,, FAULT EN GND Pin Description V CC HIN,, LIN,, FAULT EN RCIN ITRIP V SS PIN NO. PIN NAME PIN FUNCTION V B,
SOIC8 -Phase Bridge Driver General Description The is a high voltage, high speed power MOSFET and IGBT drivers with a three independent high and low side referenced output channels for -phase applications.
TF2103. Half-Bridge Gate Driver. Description. Features. Applications. Ordering Information. Typical Application. Advance Info.
Features Floating high-side driver in bootstrap operation to 600V Drives two N-channel MOSFETs or IGBTs in a half bridge configuration 290mA source/600ma sink output current capability Outputs tolerant
100V VCC VB 6 IRS10752 HO 5 VS 4. To Load. IRS10752LPBF SOT-23-6L Tape and Reel 3000 IRS10752LTRPBF
HVIC TM Features SOT-23 High-Side Gate Driver IC Description Floating gate driver designed for bootstrap operation Fully operational to +100 V Excellent dv/dt immunity Excellent negative V S transient
HALF-BRIDGE DRIVER. Features. Packages. Product Summary
June 1, 211 HALF-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 V
IRS2136/IRS21362/IRS21363/IRS21365/ IRS21366/IRS21367/IRS21368 (J&S) PbF 3-PHASE BRIDGE DRIVER
Data Sheet No. PD6272 IRS2136/IRS21362/IRS21363/IRS21365/ IRS21366/IRS21367/IRS21368 (J&S) PbF 3-PHASE BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V
IX2127NTR. High-Voltage Power MOSFET & IGBT Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features.
High-Voltage Power MOSFET & IGBT Driver Driver Characteristics Parameter Rating Units V OFFSET 6 V I O +/- (Source/Sink) 25/5 ma V th 25 mv t ON / t OFF (Typical) 1 ns Features Floating Channel Designed
FAN7391 High-Current, High & Low-Side, Gate-Drive IC
FAN7391 High-Current, High & Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 4.5 A / 4.5 A Sourcing / Sinking Current Driving Capability Common-Mode dv/dt Noise-Canceling
ADVANCE INFO TF Half -Bridge Driver. Features. Description. Applications. Ordering Information. Typical Application ADVANCE INFO.
Half -Bridge Driver Features Floating high-side driver in bootstrap operation to 600V Drives two N-channel MOSFETs or IGBTs in a half bridge configuration Outputs tolerant to negative transients Programmable
IR2153Z PD SELF-OSCILLATING HALF-BRIDGE DRIVER. Features. Product Summary
Features Floating channel designed for bootstrap operation Fully operational to +600 Tolerant to negative transient voltage d/dt immune Undervoltage lockout Programmable oscillator frequency 1 f = 1.4
Features. Product Marking Reel Size (inches) Tape Width (mm) Quantity per Reel DGD21844S14-13 DGD ,500
HALF- BRIDGE GATE DRIVER IN SO-14 Description The is a high voltage / high speed gate driver capable of driving N-Channel MOSFETs and IGBTs in a half bridge configuration. High voltage processing techniques
IR3101 Series 1.6A, 500V
Half-Bridge FredFet and Integrated Driver Features Output power FredFets in half-bridge configuration High side gate drive designed for bootstrap operation Bootstrap diode integrated into package. Lower
SELF-OSCILLATING HALF-BRIDGE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +600V olerant to negative transient voltage dv/dt immune Undervoltage lockout Programmable oscillator frequency 1 f = 1.4
IX2113BTR. 600V High and Low Side Gate Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features. Ordering Information
V High and Low Side Gate Driver Driver Characteristics Parameter Rating Units V OFFSET V I O +/- (Source/Sink) / A V OUT - V t on /t off / ns Delay Matching (Max) ns Features Floating Channel for Bootstrap
IR2153/IR2153D SELF-OSCILLATING HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connections
Features Floating channel designed for bootstrap operation Fully operational to 600V Tolerant to negative transient voltage dv/dt immune Undervoltage lockout Programmable oscillator frequency 1 f = 1.4
FAN73901 High- and Low-Side, Gate-Drive IC
FAN7391 High- and Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 2.5 A / 2.5 A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling
QS54/74FCT373T, 2373T. High-Speed CMOS Bus Interface 8-Bit Latches MDSL QUALITY SEMICONDUCTOR, INC. 1 DECEMBER 28, 1998
Q QUALITY SEMICONDUCTOR, INC. QS54/74FCT373T, 2373T High-Speed CMOS Bus Interface 8-Bit Latches QS54/74FCT373T QS54/74FCT2373T FEATURES/BENEFITS Pin and function compatible to the 74F373 74FCT373 and 74ABT373
IRS SOT-23 High-Side Gate Driver IC IRS10752LPBF. Features. Description. Package Options. Applications. Typical Connection Diagram
µhvic TM Features SOT-23 High-Side Gate Driver IC Description Floating gate driver designed for bootstrap operation Fully operational to +100 V Excellent dv/dt immunity Excellent negative V S transient
IX2127NTR. High-Voltage Power MOSFET & IGBT Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features.
High-Voltage Power MOSFET & IGBT Driver Driver Characteristics Parameter Rating Units V OFFSET 6 V I O +/- (Source/Sink) 25/5 ma V th 25 mv t ON / t OFF (Typical) 1 ns Features Floating Channel Designed
FAN7191-F085 High-Current, High and Low Side Gate Drive IC
FAN7191-F85 High-Current, High and Low Side Gate Drive IC Features! Floating Channel for Bootstrap Operation to +6V! 4.5A Sourcing and 4.5A Sinking Current Driving Capability! Common-Mode dv/dt Noise Cancelling
ELECTRONIC GIANT. EG3013 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG33 Datasheet Copyright 22 by EGmicro Corporation REV. EG33 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
ELECTRONIC GIANT. EG3012 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG32 Datasheet Copyright 22 by EGmicro Corporation REV. EG32 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
IXD611S1 IXD611S7. 600V, 600 ma High & Low-side Driver for N-Channel MOSFETs and IGBTs. Features. General Description
IXD V, ma High & Low-side Driver for N-Channel MOSFETs and IGBTs IXD Features Floating High Side Driver with boot-strap Power supply along with a Low Side Driver. Fully operational to V ± V/ns dv/dt immunity
FAN7371 High-Current High-Side Gate Drive IC
FAN1 High-Current High-Side Gate Drive IC Features! Floating Channel for Bootstrap Operation to +V! A/A Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling Circuit!.V and V Input
FAN7392 High-Current, High- and Low-Side, Gate-Drive IC
FAN7392 High-Current, High- and Low-Side, Gate-Drive IC Features Floating Channel for Bootstrap Operation to +6V 3A/3A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling Circuit
NTE4055B and NTE4056B Integrated Circuit CMOS, BCD to 7 Segment Decoder/Drivers
NTE4055B and NTE4056B Integrated Circuit CMOS, BCD to 7 Segment Decoder/Drivers Description: The NTE4055B ( Display Frequency Output) and NTE4056B (Strobed Latch Function) are single digit BCD to 7 segment
Quad 2-Input NAND Gate High-Voltage Silicon-Gate CMOS
TECHNICAL DATA Quad 2-Input NAND Gate High-oltage Silicon-Gate CMOS The NAND gates provide the system designer with direct emplementation of the NAND function. Operating oltage Range:.0 to 18 Maximum input
DS1040 Programmable One-Shot Pulse Generator
www.dalsemi.com FEATURES All-silicon pulse width generator Five programmable widths Equal and unequal increments available Pulse widths from 5 ns to 500 ns Widths are stable and precise Rising edge-triggered
FAN7361, FAN7362 High-Side Gate Driver
FAN7361, FAN7362 High-Side Gate Driver Features! Floating Channel Designed for Bootstrap Operation to +600V! Typically 250mA/500mA Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling
Basic Characteristics of Digital ICs
ECEN202 Section 2 Characteristics of Digital IC s Part 1: Specification of characteristics An introductory look at digital IC s: Logic families Basic construction and operation Operating characteristics
SELF-OSCILLATING FULL-BRIDGE DRIVER IC
Data Sheet No. PD60259 ADVANCE INFOMATION IS2453D(S)PbF SELF-OSCILLATING FULL-BIDGE DIVE IC Features Integrated 600V Full-Bridge Gate Driver CT, T programmable oscillator 15.6V Zener Clamp on Micropower
Package. Figure1. Typical Application Resonant Converter (LLC type)
General Description The PN7106A/B is a high voltage, high speed power MOSFET and IGBT driver based on P_SUB P_EPI process. The floating channel driver can be used to drive two N-channel power MOSFET or
SELF-OSCILLATING HALF BRIDGE
Features Output Power MOSFETs in half-bridge configuration High side gate drive designed for bootstrap operation Bootstrap diode integrated into package (HD type) Accurate timing control for both Power
30 A Low-Side RF MOSFET Driver IXRFD631
A Low-Side RF MOSFET Driver IXRFD Features High Peak Output Current Low Output Impedance Low Quiescent Supply Current Low Propagation Delay High Capacitive Load Drive Capability Wide Operating Voltage
Features. Ordering Information VCC MIC8114 RESET
MIC8114 Microprocessor Reset Circuit General Description The MIC8114 is an inexpensive microprocessor supervisory circuit that monitors the power supply in microprocessor based systems. The function of
DS1021 Programmable 8-Bit Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay Models with 0.25 ns and 0.5 ns steps Programmable using 3-wire serial port or 8- bit parallel port Leading and trailing edge accuracy Economical Auto-insertable,
8K x 8 Static RAM CY6264. Features. Functional Description
8K x 8 Static RAM Features 55, 70 ns access times CMOS for optimum speed/power Easy memory expansion with CE 1, CE 2, and OE features TTL-compatible inputs and outputs Automatic power-down when deselected
74VHCT244ATTR OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED)
OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) HIGH SPEED: t PD = 5.4 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.),
SENSE AMPS POWER DOWN
185 CY7C185 8K x 8 Static RAM Features High speed 15 ns Fast t DOE Low active power 715 mw Low standby power 220 mw CMOS for optimum speed/power Easy memory expansion with,, and OE features TTL-compatible
IX2120BTR. 1200V High and Low Side Gate Driver INTEGRATED CIRCUITS DIVISION. Description. Driver Characteristics. Features. Ordering Information
IX High and Low Side Gate Driver Driver Characteristics Parameter Rating Units OFFSET I O +/- (Source/Sink) / A OUT - t on /t off / ns Features Floating Channel for Bootstrap Operation to + Outputs Capable
DS in-1 Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay 3 independent buffered delays Delay tolerance ±2ns for -10 through 60 Stable and precise over temperature and voltage range Leading and trailing edge accuracy
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
MIC4421/4422. Bipolar/CMOS/DMOS Process. General Description. Features. Applications. Functional Diagram. 9A-Peak Low-Side MOSFET Driver
9A-Peak Low-Side MOSFET Driver Micrel Bipolar/CMOS/DMOS Process General Description MIC4421 and MIC4422 MOSFET drivers are rugged, efficient, and easy to use. The MIC4421 is an inverting driver, while