ELECTRONIC GIANT. EG3013 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
|
|
- Marybeth Patrick
- 5 years ago
- Views:
Transcription
1 ELECTRONIC GIANT EG33 Datasheet Copyright 22 by EGmicro Corporation REV.
2 EG33 datasheet Contents. Features General Description Applications Device Information Pin map Pin Functions Block Diagram Application Schematics Electrical Characteristics Absolute maximum ratings Recommended operating conditions Timing Diagram Function Description Supply voltage Input stage and Output stage Bootstrap Package Information SOP8 Dimension... Copyright 22 by EGmicro Corporation /
3 EG33 datasheet EG33 Datasheet V.. Features Floating high side driver in bootstrap operation to +V, build in bootstrap diode Internal fixed dead time of 2nS Cross-conduction prevention logic 8mA source/ma sink output current capability Driving N-channel MOSFETs and IGBTs in a half-bridge configuration High side output,in phase with input Low side output, out of phase with input Minimal peripheral components Low quiescent current:4.5ma Package:SOP8 2. General Description The EG33 is a cost effective half-bridge driver IC designed for N-channel MOSFETs and IGBTs. The EG33 includes a combined logic inputs for low and high-side drives, fixed dead time to protect FETs, cross-conduction prevention logic, high voltage level shifter, noise filter enhanced immunity, and provide high current capability for external N-channel MOSFETs, application for brushless motor drives. The bootstrap operation voltage of EG33 is up to VDC, the operation voltage of is between 4.5V to 3V, and quiescent supply current is only 4.5mA. Build in simultaneous conduction lockout protection, and build in pull down resistors of K on and pull up a current source of 3uA on, when input pins are floating, the outputs of and are held to low, the structure of high current Darlington is used in output stage, the EG33 is available in a SOP8 package. 3. Applications E-bike controller V synchronous Buck converter Class D power amplifies Brushless pump controller BLDC Motor drive Copyright 22 by EGmicro Corporation 2 /
4 4. Device Information EG33 datasheet 4.. Pin map V B VS EG GND Figure 4-. EG33 pin map 4.2. Pin Functions Designator Name I/O Descriptions Power Supply voltage 2 I Logic input for high side gate driver output, in phase 3 I Logic input for low side gate driver output, out of phase 4 GND GND Ground 5 O Output gate driver for low side MOSFET 6 VS O High side bootstrap return 7 O Output gate driver for high side MOSFET 8 VB Power Bootstrap supply voltage Copyright 22 by EGmicro Corporation 3 /
5 5. Block Diagram EG33 datasheet 2 Hin Input K K Level Shift Noise Filter Driver VB Dead Time 6 VS K 3 Lin Input K Driver 5 4 GND Fig 5-. EG33 block diagram 6. Application Schematics +5V +Vin U C.uF L IN 2 3 EG VB VS D R N448 C3 nf Q C2 47uF GND 4 5 OUT D2 N448 R2 C4 nf Q2 Fig 6-. EG33 typical application schematic I for middle power motor Copyright 22 by EGmicro Corporation 4 /
6 +5V EG33 datasheet +Vin U C.uF L IN GND 2 3 EG VB VS D N448 R C3 nf R3 2 D3 FR7 Q C2 47uF OUT D2 N448 R2 C4 nf Q2 Fig 6-2. EG33 typical application schematic II for high power motor +5V +Vin D3 FR7 U C.uF L IN 2 3 EG VB VS D R N448 C3 nf Q C2 47uF GND 4 5 OUT D2 N448 R2 C4 nf Q2 Fig 6-3. EG33 typical application schematic III for external bootstrap diode Copyright 22 by EGmicro Corporation 5 /
7 7. Electrical Characteristics EG33 datasheet 7. Absolute maximum ratings TA=25 unless otherwise specified Symbol Parameter Conditions Min Max Unit VB Bootstrap supply V VS Bootstrap return V High side drive output V Low side drive output V VCC Supply voltage V High side input V Low side input V TA Ambient temperature Tstr Storage temperature TL Lead temperature T=S - 3 Note:Exceeding extreme conditions may permanently damage the chip. EG33 s reliability may be affected running at the extreme conditions for a long time. Copyright 22 by EGmicro Corporation 6 /
8 7.2 Recommended operating conditions EG33 datasheet TA=25,=5V, CL=nF,unless otherwise specified Parameter Symbol Conditions Min TYP Max Unit Supply voltage V Quiescent current Icc All input pins is floating,=5v ma Logic input voltage Vin(H) & V Logic input voltage Vin(L) & -.3. V Logic input bias current Iin(H) Vin=5V ua Logic input bias current Iin(L) Vin=V - - ua Switching time characteristics for Turn on propagation delay Ton See the Figure ns Turn off propagation delay Toff See the Figure ns Turn on rise time Tr See the Figure ns Turn off fall time Tf See the Figure ns Switching time characteristics for Turn on propagation delay Ton See the Figure ns Turn off propagation delay Toff See the Figure ns Turn on rise time Tr See the Figure ns Turn off fall time Tf See the Figure ns Dead time Dead time DT See the Figure7-3, and CL= ns Drive Capability Output high short circuit pulsed current IO+ Vo=V,VIN=VIH PW us A Output low short circuit pulsed current IO- Vo=5V,VIN=VIL PW us.8 - A Copyright 22 by EGmicro Corporation 7 /
9 7.3 Timing Diagram EG33 datasheet 5% 5% 5% 5% Ton Tr Toff Tf Ton Tr Toff Tf 9% 9% % % 9% 9% % % Figrue7-. Switching time waveform definitions of Figrue7-2. Switching time waveform definitions of 5% 5% 9% DT 9% % DT % Figure7-3. Dead time waveform definitions Copyright 22 by EGmicro Corporation 8 /
10 8. Function Description EG33 datasheet 8. Supply voltage The recommended VCC operating voltage of EG33 is between V to 5V for power MOSFETs. The internal logic circuit and driver stage of EG32 share the same supply of VCC, the internal ground of logic circuit and driver stage are also connected together. 8.2 Input stage and Output stage The EG33 includes a combined logic inputs, dead time, high voltage level shifter, bootstrap circuit, high current Darlington output stage. the input pins of EG33 features typical high threshold of 2.5V and typical low threshold of.v, the input pins are conveniently drive with logic level PWM control signals from MCU digital controller device. Each output stage in EG33 is capable of supplying.8a peak source and A peak sink current, floating high side driver in bootstrap operation is up to VDC. The EG33 features excellent propagation delay between input and output. In low side driver, with 5nS turn on propagation delay is over to, with 5ns turn off propagation delay is over to. In high side driver, with 3ns turn on propagation delay is over to, with 4ns turn off propagation delay is over to. Input/Output Logic Relationship as shown in Figure 8-2: Figure 8-2. Input/Output logic relationship Copyright 22 by EGmicro Corporation 9 /
11 EG33 datasheet Input/Output Logic Table: Input Output (Pin4) (Pin3) (Pin7) (Pin5) From above logic table view, Case A: when and are low at same time, will output high to turn on low side MOSFET and will output low to turn off high side MOSFET. Case B: when and low and are high at same time, will output high to turn on high side MOSFET and will output low to turn off low side MOSFET. Case C: when goes low and goes high or goes high and goes low, and will simultaneously output low to turn off high and low side MOSFET, the interlock and dead time functions prevent both outputs from being turned on simultaneously. 8.3 Bootstrap The EG33 uses a bootstrap structure, which has the advantage of being simply and low cost. The Figure 8-3 will help to understand the operation of bootstrap circuit. The voltage at VCC forces current through the internal bootstrap diode or external bootstrap diode, bootstrap capacitor and low side MOSFET, which will charge the bootstrap capacitor to prepare it for driving the high side MOSFET. +48V External bootstrap diode FR7 8 VB VS VC Bootstrap capacitor +5V VCC 3 5 EG33 Figure 8-3. EG33 Bootstrap circuit structure Copyright 22 by EGmicro Corporation /
12 9. Package Information EG33 datasheet 9. SOP8 Dimension Copyright 22 by EGmicro Corporation /
ELECTRONIC GIANT. EG3012 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG32 Datasheet Copyright 22 by EGmicro Corporation REV. EG32 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
More informationELECTRONIC GIANT. EG3113 Datasheet. Half-Bridge Driver. Copyright 2017 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG33 Datasheet Copyright 27 by EGmicro Corporation REV. EG33 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
More informationFAN7191-F085 High-Current, High and Low Side Gate Drive IC
FAN7191-F85 High-Current, High and Low Side Gate Drive IC Features! Floating Channel for Bootstrap Operation to +6V! 4.5A Sourcing and 4.5A Sinking Current Driving Capability! Common-Mode dv/dt Noise Cancelling
More informationTF2103. Half-Bridge Gate Driver. Description. Features. Applications. Ordering Information. Typical Application. Advance Info.
Features Floating high-side driver in bootstrap operation to 600V Drives two N-channel MOSFETs or IGBTs in a half bridge configuration 290mA source/600ma sink output current capability Outputs tolerant
More informationV OFFSET. Description
Features n Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
More informationPackage. Figure1. Typical Application Resonant Converter (LLC type)
General Description The PN7106A/B is a high voltage, high speed power MOSFET and IGBT driver based on P_SUB P_EPI process. The floating channel driver can be used to drive two N-channel power MOSFET or
More informationHigh voltage high- and low-side driver for automotive applications. Description. Figure 1. Block diagram BOOTSTRAP DRIVER 8 R S LEVEL SHIFTER
High voltage high- and low-side driver for automotive applications Datasheet - production data Outputs in phase with inputs Interlocking function AECQ100 automotive qualified Features SO-8 High voltage
More informationHIGH AND LOW SIDE DRIVER
Data Sheet No. PD-O Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
More informationFAN7371 High-Current High-Side Gate Drive IC
FAN1 High-Current High-Side Gate Drive IC Features! Floating Channel for Bootstrap Operation to +V! A/A Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling Circuit!.V and V Input
More informationL6398. High voltage high and low-side driver. Applications. Description. Features
High voltage high and low-side driver Applications Datasheet - production data Motor driver for home appliances, factory automation, industrial drives and fans. Features High voltage rail up to 600 V dv/dt
More informationSLLIMM -nano small low-loss intelligent molded module IPM, 3 A, 600 V, 3-phase IGBT inverter bridge. Description. Table 1: Device summary
SLLIMM -nano small low-loss intelligent molded module IPM, 3 A, 600 V, 3-phase IGBT inverter bridge Datasheet - production data Features IPM 3 A, 600 V, 3-phase IGBT inverter bridge including control ICs
More informationHalf-Bridge Driver IR25606SPBF. Features. Product Summary. Description. Package Options. Ordering Information
Half-Bridge Driver Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Undervoltage
More informationIR2304(S) & (PbF) HALF-BRIDGE DRIVER Product Summary
Data Sheet No. PD60200 revb Features Floating channel designed for bootstrap operation to +600V. Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Under voltage
More informationADVANCE INFO TF Half -Bridge Driver. Features. Description. Applications. Ordering Information. Typical Application ADVANCE INFO.
Half -Bridge Driver Features Floating high-side driver in bootstrap operation to 600V Drives two N-channel MOSFETs or IGBTs in a half bridge configuration Outputs tolerant to negative transients Programmable
More informationIXD611S1 IXD611S7. 600V, 600 ma High & Low-side Driver for N-Channel MOSFETs and IGBTs. Features. General Description
IXD V, ma High & Low-side Driver for N-Channel MOSFETs and IGBTs IXD Features Floating High Side Driver with boot-strap Power supply along with a Low Side Driver. Fully operational to V ± V/ns dv/dt immunity
More informationL6385E. High voltage high and low-side driver. Description. Features. Applications
High voltage high and low-side driver Description Datasheet - production data Features High voltage rail up to 600 V dv/dt immunity ± 50 V/nsec in full temperature range Driver current capability: 400
More information200V HO V DD V B HIN SD HIN SD V S TO LOAD LIN V CC V SS LIN COM LO
Data Sheet No. PD6195-E Features Floating channel designed for bootstrap operation Fully operational to Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 to V Undervoltage
More informationFAN73901 High- and Low-Side, Gate-Drive IC
FAN7391 High- and Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 2.5 A / 2.5 A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling
More informationIRS2103(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection. 600 V max. 130 ma/270 ma 10 V - 20 V V OFFSET
Data Sheet No. PD6263 Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage
More informationL6385 HIGH-VOLTAGE HIGH AND LOW SIDE DRIVER
HIGH-VOLTAGE HIGH AND LOW SIDE DRIVER HIGH VOLTAGE RAIL UP TO 600 V dv/dt IMMUNITY +- 50 V/nsec IN FULL TEM- PERATURE RANGE DRIVER CURRENT CAPABILITY: 400 ma SOURCE, 650 ma SINK SWITCHING TIMES 50/30 nsec
More informationL6386AD. High voltage high and low-side driver. Description. Features. Applications
High voltage high and low-side driver Description Datasheet - production data Features High voltage rail up to 600 V dv/dt immunity ± 50 V/nsec in full temperature range Driver current capability 400 ma
More informationL6392. High voltage high and low-side driver. Applications. Description. Features
High voltage high and low-side driver Applications Datasheet - production data Motor driver for home appliances, factory automation, industrial drives. HID ballasts, power supply units. Description Features
More informationL6399. High voltage high and low-side driver. Applications. Features. Description
High voltage high and low-side driver Applications Datasheet - production data Features High voltage rail up to 600 V dv/dt immunity ± 50 V/ns over full temperature range Driver current capability: 290
More informationSLLIMM small low-loss intelligent molded module IPM, 3-phase inverter - 15 A, 600 V short-circuit rugged IGBT. Description. Table 1.
SLLIMM small low-loss intelligent molded module IPM, 3-phase inverter - 15 A, 600 V short-circuit rugged IGBT Applications Datasheet - production data 3-phase inverters for motor drives Home appliance,
More informationTypical Application Circuit V CC HIN,, LIN,, FAULT EN GND Pin Description V CC HIN,, LIN,, FAULT EN RCIN ITRIP V SS PIN NO. PIN NAME PIN FUNCTION V B,
SOIC8 -Phase Bridge Driver General Description The is a high voltage, high speed power MOSFET and IGBT drivers with a three independent high and low side referenced output channels for -phase applications.
More informationFAN7361, FAN7362 High-Side Gate Driver
FAN7361, FAN7362 High-Side Gate Driver Features! Floating Channel Designed for Bootstrap Operation to +600V! Typically 250mA/500mA Sourcing/Sinking Current Driving Capability! Common-Mode dv/dt Noise Canceling
More informationNot recommended for new designs. No replacement is available
Aug 2, 28 IRS218S SINGLE HIGH SIDE DRIVER IC IC Features Gate drive supply range from 1 V to 2 V Undervoltage lockout for V BS and V CC 3.3 V and V input logic compatible Tolerant to negative transient
More informationPackages. Input logic. Part HIN/LIN yes
Data Sheet No. PD60209 revc Features Floating channel designed for bootstrap operation Fully operational to +600V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to
More informationIXA531L4. Preliminary Data Sheet. 500mA 3-Phase Bridge Driver. Features. General Description. Applications. Ordering Information
500mA 3-Phase Bridge Preliminary Data Sheet Features Fully operational to +650V Tolerant of negative transient voltages dv/dt immune (50V/ns) Latch-up protected over entire operating range Fault-current
More informationFAN8811/D. High-Frequency, High Side and Low Side Gate Driver IC FAN8811T MPX
High-Frequency, High Side and Low Side Gate Driver IC The FAN88 is high side and low side gate-drive IC designed for highvoltage, high-speed, driving MOSFETs operating up to 8. The FAN88 integrates a driver
More informationPackages. Crossconduction. Input logic. Part. prevention logic COM HIN/LIN no none 21814
Data Sheet No. PD014-D Features Floating channel designed for bootstrap operation Fully operational to +00V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 10 to 20V Undervoltage
More informationFAN73932 Half-Bridge Gate Drive IC
FAN73932 Half-Bridge Gate Drive IC Features Floating Channel for Bootstrap Operation to +600V Typically 2.5A/2.5A Sourcing/Sinking Current Driving Capability Extended Allowable Negative V S Swing to -9.8V
More informationIRS2181/IRS21814(S)PbF
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout for both
More informationFeatures. Product Marking Reel Size (inch) Tape Width (mm) Quantity per Reel DGD2103MS8-13 DGD2103M ,500
HALF-BRIDGE GATE DRIVER IN SO-8 Description The is a high-voltage / high-speed gate driver capable of driving N-channel MOSFETs and IGBTs in a half-bridge configuration. High voltage processing techniques
More informationIRS2183/IRS21834(S)PbF
Data Sheet No. PD Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage
More informationApplication Note AN-1125
Application Note AN- IRS(7,8,7) and IR(7,8,7) Comparison By Jason Nguyen, Fang, David New Table of Contents Page Introduction... Block Diagram... Electrical Characteristic Differences... Figures... Summary...
More informationIRS211(7,71,8)(S) SINGLE CHANNEL DRIVER
February 18, 29 SINGLE CHANNEL DRIVER IC Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
More informationIRS2113MPBF HIGH- AND LOW-SIDE DRIVER
February 8, 2012 IRS2113MPBF HIGH- AND LOW-SIDE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +600 V Tolerant to negative transient voltage dv/dt immune Gate drive
More informationNIKO-SEM N3860V N3860P REV: A CURRENT MODE PWM CONTROLLER GENERAL DESCRIPTION FEATURES DEVICE SELECTION GUIDE
GENERAL DESCRIPTION The N80 is a low cost, low start-up current, low operating current, current mode PWM controller, specifically designed for the lower stand-by power consumption. The device allows the
More informationIntegrated Power Hybrid IC for Appliance Motor Drive Applications
Integrated Power Hybrid IC for Appliance Motor Drive Applications PD-97277 Rev A IRAM336-025SB Series 3 Phase Inverter HIC 2A, 500V Description International Rectifier s IRAM336-025SB is a multi-chip Hybrid
More informationFeatures. Product Marking Reel Size (inches) Tape Width (mm) Quantity per Reel DGD2304S8-13 DGD ,500
HALF-BRIDGE GATE DRIVER IN SO-8 Description Features The is a high voltage / high speed gate driver capable of driving N-channel MOSFETs and IGBTs in a half bridge configuration. High voltage processing
More informationV OFFSET 600V max. I O +/- 130 ma / 270 ma V OUT. Packages
Data Sheet No. PD-S Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to 2V Undervoltage
More informationPin Definition: 1. VCC 8. VB 2. RT 7. HO 3. CT 6. VS 4. COMP 5. LO
DIP-8 SOP-8 Pin Definition: 1. VCC 8. VB 2. RT 7. HO 3. CT 6. VS 4. COMP 5. LO Description is a high voltage, high speed, self-oscillating power MOSFET and IGBT driver with both high and low side referenced
More information3-PHASE BRIDGE DRIVER
Features Floating channel designed for bootstrap operation. Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V (IRS2136D/ IRS21368D),11.5
More informationIR20153S & (PbF) HIGH SIDE DRIVER WITH RECHARGE
Preliminary Data Sheet PD60214 Rev B Features Floating channel designed for bootstrap operation Fully operational up to 150V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
More informationFAN7085-GF085 High Side Gate Driver with Recharge FET
FAN7085-GF085 High Side Gate Driver with Recharge FET Features Qualified to AEC Q100 Floating channel designed for bootstrap operation fully operational up to 300V. Tolerance to negative transient voltage
More informationIRS2136/IRS21362/IRS21363/IRS21365/ IRS21366/IRS21367/IRS21368 (J&S) PbF 3-PHASE BRIDGE DRIVER
Data Sheet No. PD6272 IRS2136/IRS21362/IRS21363/IRS21365/ IRS21366/IRS21367/IRS21368 (J&S) PbF 3-PHASE BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V
More informationIRS21956S Floating Input, High and Low(Dual mode) Side Driver
January 16, 2009 Datasheet No. - PD97375 IRS21956S Floating Input, High and Low(Dual mode) Side Driver Features Low side programmable ramp gate drive Low side generic gate drive integrated using the same
More informationHigh-Current, High & Low-Side, Gate-Drive IC
FAN739 High-Current, High & Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6V Typically 4.5A/4.5A Sourcing/Sinking Current Driving Capability Common-Mode dv/dt Noise Canceling
More informationDescription. Operating Temperature Range
FAN7393 Half-Bridge Gate Drive IC Features Floating Channel for Bootstrap Operation to +6V Typically 2.5A/2.5A Sourcing/Sinking Current Driving Capability Extended Allowable Negative V S Swing to -9.8V
More informationIX6R Volt, 6 Ampere High & Low-side Driver for N-Channel MOSFETs and IGBTs
Features Floating High Side Driver with boot-strap Power supply along with a Low Side Driver. Fully operational to 00V ± 0V/ns dv/dt immunity Gate drive power supply range: - V Undervoltage lockout for
More informationIR2105 HALF BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection
Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to 2V Undervoltage lockout V Schmitt-triggered
More informationL6498. High voltage high and low-side 2 A gate driver. Description. Features. Applications
High voltage high and low-side 2 A gate driver Description Datasheet - production data Features Transient withstand voltage 600 V dv/dt immunity ± 50 V/ns in full temperature range Driver current capability:
More informationHIGH AND LOW SIDE DRIVER. Product Summary VOFFSET VOUT. Description
Features n Floating channel designed for bootstrap operation Fully operational to +4V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
More informationIR2112(S) HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET. 600V max. 200 ma / 420 ma 10-20V
Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both
More informationIRS2104(S)PbF HALF-BRIDGE DRIVER. Features. Product Summary. Packages. Description. Typical Connection V OFFSET. 600 V max. 130 ma/270 ma 10 V - 20 V
Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage lockout. V, V,
More informationRT9607/A Dual Channel Synchronous-Rectified Buck MOSFET Driver General Description Features Drives Four N-MOSFETs Adaptive Shoot-Through Protection
Dual Channel Synchronous-Rectified Buck MOSFET Driver General Description The RT9607/A is a dual power channel MOSFET driver specifically designed to drive four power N-MOSFETs in a synchronous-rectified
More informationTL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power-Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationHIGH VOLTAGE HALF BRIDGE
Preliminary Data Sheet No. PD0-D IR0HDC0U-P HIGH LTAGE HALF BRIDGE Features Output Power IGBT s in half-bridge configuration 55V rated breakdown voltage High side gate drive designed for bootstrap operation
More informationIR2302(S) & (PbF) HALF-BRIDGE DRIVER. Packages
Data Sheet No. PD7 Rev.A Features Floating channel designed for bootstrap operation Fully operational to +V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from to V Undervoltage
More informationIRS2184/IRS21844(S)PbF
Data Sheet No. PD Features Floating channel designed for bootstrap operation Fully operational to + V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from V to V Undervoltage
More informationFAN7391 High-Current, High & Low-Side, Gate-Drive IC
FAN7391 High-Current, High & Low-Side, Gate-Drive IC Features Floating Channels for Bootstrap Operation to +6 V Typically 4.5 A / 4.5 A Sourcing / Sinking Current Driving Capability Common-Mode dv/dt Noise-Canceling
More informationData sheet, Rev. 2.1, Dec ED003L06-F. Integrated 3 Phase Gate Driver. Power Management & Drives
Data sheet, Rev. 2.1, Dec 2008 6ED003L06-F Power Management & Drives N e v e r s t o p t h i n k i n g 6ED003L06-F Revision History: 2009-07 Rev. 2.1 Previous Version: 2.0 Page Subjects (major changes
More informationIRS2453(1)D(S) Product Summary
Features Integrated 600 V full-bridge gate driver CT, RT programmable oscillator 15.6 V Zener clamp on V CC Micropower startup Logic level latched shutdown pin Non-latched shutdown on CT pin (1/6th V CC
More informationSELF-OSCILLATING FULL-BRIDGE DRIVER IC
Data Sheet No. PD60259 ADVANCE INFOMATION IS2453D(S)PbF SELF-OSCILLATING FULL-BIDGE DIVE IC Features Integrated 600V Full-Bridge Gate Driver CT, T programmable oscillator 15.6V Zener Clamp on Micropower
More informationLDIP- IPM IM (Preliminary)
LDIP- IPM (Preliminary) Description Cyntec IPM is integrated Drive, protection and system control functions that is designed for high performance 3-phase motor driver application like: Home appliances
More informationIntegrated Power Module for Small Appliance Motor Drive Applications
2.2Ω, 500V Integrated Power Module for Small Appliance Motor Drive Applications Description IRSM505-035 and IRSM515-035 are 3-phase Integrated Power Modules (IPM) designed for advanced appliance motor
More informationHIGH SPEED, 100V, SELF OSCILLATING 50% DUTY CYCLE, HALF-BRIDGE DRIVER
Data Sheet No. 60206 HIGH SPEED, 100V, SELF OSCILLATING 50% DUTY CYCLE, HALF-BRIDGE DRIVER Features Simple primary side control solution to enable half-bridge DC-Bus Converters for 48V distributed systems
More informationRT9603. Synchronous-Rectified Buck MOSFET Drivers. General Description. Features. Applications. Ordering Information. Pin Configurations
Synchronous-Rectified Buck MOSFET Drivers General Description The RT9603 is a high frequency, dual MOSFET drivers specifically designed to drive two power N-MOSFETs in a synchronous-rectified buck converter
More informationREV1.0 - AUG 2012 RELEASED
DESCRIPTION The consists of step-down switching regulator with PWM control. These devises include a reference voltage source, oscillation circuit, error amplifier, internal PMOS and etc. provides low-ripple
More informationI n t e g r a t e d 3 P h a s e G a t e D r i v e r
Data sheet, Rev. 2. 2, S e p t. 2 0 1 1 6ED003L06-F I n t e g r a t e d 3 P h a s e G a t e D r i v e r Power Management & Drives N e v e r s t o p t h i n k i n g 6ED003L06-F Revision History: 2011-08
More informationSP6018 Synchronous Rectifier Driver
DESCRIPTION The fundamental of SP6018 synchronous rectifier (SR) driver IC is based on our U.S. patented methods that utilize the principle of prediction logic circuit. The IC deliberates previous cycle
More informationISL6700. Preliminary. 80V, 1.25A Peak Current Half-Bridge MOSFET Driver. itle P40. Features. Description. b- t V, 5A k r- thdge. T ver) Applications
TM itle P40 b- t V, 5A k r- thdge T ver) thor y- rds ter- i- - tor, 40, l dge, Preliminary January 16, 2002 Features Drives 2 N-Channel MOSFETs in Half-Bridge Configuration Bootstrap Supply Max Voltage
More informationMP86884 Intelli-Phase TM Solution (Integrated HS/LS FETs and Driver) in 6x6mm TQFN
The Future of Analog IC Technology MP86884 Intelli-Phase TM Solution (Integrated HS/LS FETs and Driver) in 6x6mm TQFN DESCRIPTION The MP86884 is a monolithic half-bridge with built-in internal power MOSFETs
More informationFAN7384 Half-Bridge Gate-Drive IC
FAN7384 Half-Bridge Gate-Drive IC Features Floating Channel for Bootstrap Operation to +6V Typically 25mA/5mA Sourcing/Sinking Current Driving Capability for Both Channels Extended Allowable Negative V
More informationKA7500B. SMPS Controller. Features. Description. Internal Block Diagram.
SMPS Controller www.fairchildsemi.com Features Internal Regulator Provides a Stable 5V Reference Supply Trimmed to 5% Uncommitted Output TR for 200mA Sink or Source Current Output Control For Push-Pull
More informationIR11682S DUAL SmartRectifier TM DRIVER IC
Datasheet No 97476 July 1, 2011 Features Secondary-side high speed controller for synchronous rectification in resonant half bridge topologies 200V proprietary IC technology Max 400KHz switching frequency
More informationRT9610C High Voltage Synchronous Rectified Buck MOSFET Driver for Notebook Computer General Description Features Drives Two N-MOSFETs
RT9610C High Voltage Synchronous Rectified Buck MOSFET Driver for Notebook Computer General Description The RT9610C is a high frequency, dual MOSFET driver specifically designed to drive two power N-MOSFETS
More informationRT9610B High Voltage Synchronous Rectified Buck MOSFET Driver for Notebook Computer General Description Features Drives Two N-MOSFETs
RT9610B High Voltage Synchronous Rectified Buck MOSFET Driver for Notebook Computer General Description The RT9610B is a high frequency, dual MOSFET driver specifically designed to drive two power N-MOSFETS
More informationFSB50760SF, FSB50760SFT Motion SPM 5 SuperFET Series
FSB50760SF, FSB50760SFT Motion SPM 5 SuperFET Series Features UL Certified No. E209204 (UL1557) 600 V R DS(on) = 530 m Max SuperFET MOSFET 3- Phase with Gate Drivers and Protection Built-in Bootstrap Diodes
More informationIR2106/IR21064 IR2107/IR21074 HIGH AND LOW SIDE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +00V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 0 to 0V Undervoltage lockout for both
More informationIR3101 Series 1.6A, 500V
Half-Bridge FredFet and Integrated Driver Features Output power FredFets in half-bridge configuration High side gate drive designed for bootstrap operation Bootstrap diode integrated into package. Lower
More informationIRS21844MPBF HALF-BRIDGE DRIVER
November 19, 2010 HALF-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to + 600 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range
More informationHigh and Low Side N-Channel Gate Driver
Features Input Voltage Range: 4.5 to 5.5 Output Voltage Range: Control Range -3V Peak MOSFET Drive current into 3nF Sink 3A Source 1A Sink 1A Source.8A Static Current (inputs at V) 175 A No-load, 25kHz
More informationLSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)
LSI/CSI UL A800 FEATURES: LSI Computer Systems, Inc. 1 Walt Whitman Road, Melville, NY 114 (1) 1-0400 FAX (1) 1-040 STEPPER MOTOR CONTROLLER Controls Bipolar and Unipolar Motors Cost-effective replacement
More informationIRS2110(-1,-2,S)PbF IRS2113(-1,-2,S)PbF HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages
Features Floating channel designed for bootstrap operation Fully operational to +5 V or +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage lockout
More informationApplication Note AN-1113
Application Note AN- IRS and IR Comparison By Jason Nguyen, Min Fang, David New Table of Contents Page Introduction... Block Diagrams... Electrical Characteristic Differences... Figures... Summary...8
More informationTL594 PULSE-WIDTH-MODULATION CONTROL CIRCUIT
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationTL594 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationIR2110 HIGH AND LOW SIDE DRIVER. Features. Product Summary. Packages. Description. Typical Connection. 500V max. V OFFSET 10-20V VOUT.
Features n Floating channel designed for bootstrap operation Fully operational to +5V Tolerant to negative transient voltage dv/dt immune n Gate drive supply range from 1 to 2V n Undervoltage lockout for
More informationSelf-Oscillating Half-Bridge Driver
Self-Oscillating Half-Bridge Driver Features Product Summary Floating channel designed for bootstrap operation Integrated 600V half-bridge gate driver 15.6V zener clamp on Vcc True micropower start up
More informationPackages. Feature Comparison. Crossconduction. Input logic. Part COM HIN/LIN no none 21064
DS No.PD6266 Rev A Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage, dv/dt immune Gate drive supply range from 1 V to 2 V Undervoltage
More informationApplication Note AN-1114
Application Note AN- IRS and IR Comparison By Jason Nguyen, Min Fang, David New Table of Contents Page Introduction... Block Diagrams... Electrical Characteristic Differences... Figures... Summary...9
More informationEM5812/A. 12A 5V/12V Step-Down Converter. Applications. General Description. Pin Configuration. Ordering Information. Typical Application Circuit
12A 5V/12V Step-Down Converter General Description is a synchronous rectified PWM controller with a built in high-side power MOSFET operating with 5V or 12V supply voltage. It achieves 10A continuous output
More informationProduct Presentation. Synchronous Buck H-Bridge H (Hi-Side) Driver MCP14628
Product Presentation Synchronous Buck H-Bridge H (Hi-Side) Driver MCP14628 April 2008 2008 Microchip Technology Incorporated. All Rights Reserved. Synchronous Buck H-Bridge (Hi-Side) Driver Slide 1 Hello
More informationHIGH SPEED, 100V, SELF OSCILLATING 50% DUTY CYCLE, FULL-BRIDGE DRIVER
查询 IR2086S 供应商 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 Data Sheet PD No.60226 IR2086S HIGH SPEED, 100V, SELF OSCILLATING 50% DUTY CYCLE, FULL-BRIDGE DRIVER Features Simple primary side control solution to enable full-bridge
More informationIR2112(S) & (PbF) HIGH AND LOW SIDE DRIVER
Features Floating channel designed for bootstrap operation Fully operational to +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both
More informationHIGH VOLTAGE HALF BRIDGE
Preliminary Data Sheet No. PD0-C IR0HDC0U-P HIGH LTAGE HALF BRIDGE Features Output Power IGBT s in half-bridge configuration 00V rated breakdown voltage High side gate drive designed for bootstrap operation
More informationHALF-BRIDGE DRIVER. Features. Packages. Product Summary
June 1, 211 HALF-BRIDGE DRIVER Features Floating channel designed for bootstrap operation Fully operational to +6 V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 V
More informationDT V 1A Output 400KHz Boost DC-DC Converter FEATURES GENERAL DESCRIPTION APPLICATIONS ORDER INFORMATION
GENERAL DESCRIPTION The DT9111 is a 5V in 12V 1A Out step-up DC/DC converter The DT9111 incorporates a 30V 6A N-channel MOSFET with low 60mΩ RDSON. The externally adjustable peak inductor current limit
More information