EMC Station Manager Data Logger

Transcription

1 EMC Statin Manager Data Lgger Envirnmental Mnitring Cmpany, Inc. 580 Linne Rad Suite 150 Pas Rbles, Califrnia, USA (800) (805) Fax: (805)

2 Frewrd We are pleased t present this manual t assist yu with the set-up, peratin and maintenance f yur Statin Manager data lgger. While every effrt has been made t prvide accurate and cncise infrmatin, Envirnmental Mnitring Cmpany, Inc., makes n warranty, expressed r implied, nr assumes respnsibility r liability regarding the cntents r use f this manual. Statin Manager is a registered trademark f Envirnmental Mnitring Cmpany, Inc., (EMC). The Statin Manager Data lgger sftware is prtected by United States cpyright laws and internatinal treaty prvisins. This sftware is the whlly wned intellectual and physical prperty f EMC, and Statin Manager Data lgger sftware may nly be perated by licensed users with the expressed written authrizatin and cnsent f EMC. If yu have questins abut this manual r need assistance with the Statin Manager Data lgger, please d nt hesitate t cntact the EMC Custmer Supprt Department at the address listed n the frnt cver. 1

3 Blank Page 2

4 Table f Cntents Sectin Descriptin Page 1.0 Intrductin General Infrmatin Statin Manager Overview Hardware Cnfiguratins Sftware Cnventinal Data Lgger Operatin Distributed Data Lgging Operatin Input/Output Mdules Main Menu Recmmended Statin Manager PC Hardware Getting Started Receive & Inspect Cmpnents Prcedures Cnnect Cmpnents Tgether Cnnecting PC Cmpnents and Peripherals Tgether Cnnect Mdular Pwer Supply t SIU Unit Cnnect Multiple SIU Units t ne Statin Manager PC Cnnect Signal Wires t I/O Mdules Cnnect Signal Wires t Analg Input Mdules Cnnect Signal Wires t Digital Input Mdules Cnnect Signal Wires t Digital Output Mdules Cnnect Signal Wires t Analg Output Mdules Cnnect Thermcuple Signal Wires t Thermcuple Input Mdules Cnnect Signal Wires t Tipping Bucket Rain Gauge PC Startup Switch On AC Pwer Startup Statin Manager Sftware Default Passwrd Install Sftware Re-Install Windws XP Change Micrsft Windws Settings Display Pwer Management Date/Time Install Sftware SIU Utility Sftware Installatin Statin Manager Sftware Installatin Upgrades Initialize Intrductin Initialize a Initializatin Menu Parameter Initializatin Table

5 Averaging Methds Initialize Plling Initialize Statin Table Initialize Cm Prts Calibratin Schedules Calibratin Sequences Statin Manager Features Statin Manager User-Interface Statin Manager Map Screen Calibratin Cntrl Prgram Initiate Calibratins Calibratin Sequence Manual Calibratin Instantaneus Data Display Print Calibratin Summary Dialg Bx View Strip Charts Dialg Bx Calibratin Schedules Table Calibratin Sequences Table Calibratin System Manually Enter Surce Values Calibratr Cmmands Timer Cntrller Timer Cntrller Table Timer Cntrller and Calibratr Prperties Timer Cntrller Applicatins Stream Switching Example Backflush Example Digital Input Example PM10 Sampler Example Manual Reprts Calibratin Cntrl Chart Digital Input-Output Table Digital Output Lines Table Digital Input Lines Table Digital Status Screen Mark Dwn Channels Screen Strip Charts Chart Selectin User Defined Strip Chart Make Chart Selectin Bx Date Select Menu Display Chart Buttn Pre-Defined Strip Chart Initialize Pre-Defined Charts Strip Chart Screen Strip Chart Scrll Bars Strip Chart Optins Statin Lgbk Statin Lgbk Edit Buttns Initializatin Initialize Statin Initialize Parameters Initialize Plling Table Initialize Statin Table Initialize Cm Prts

6 4.6.2 Initialize Reprts Reprt Setup Table Calibratin Cntrl Chart Limits Analg Output Table Quality Assurance Calibratin Cntrl Chart Excel Exprts Exprt 15-Minute Data Data Instantaneus Data Tabular Displays Hur Averages Minute Averages Minute Averages Minute Averages Real Time Data Mark Dwn Channels Manual Reprts Scheduled Reprts Reprt Setup Table Reprt Table Data Editr Edit Multiple Hurs Replace Single Hur Replace Flag(s) Alarms Parameter Alarm Table Parameter Definitins Table Alarm Update Table Relay Cnditin Table Alarm Telephne Table Digital Input Alarm Table Digital Input Message Table Alarm Histry Table Cnditin Flag Table Alarm Table Utilities Security System Define Users Define Grups Define Permissins Define Screens Calculatr Date and Time Autmatic Data Backup Pwer Failures Trubleshting Glssary Index

7 Figure Descriptin Page Figure 2-1 with 1 SIU Unit...11 Figure 2-2 with 4 SIU Units...12 Figure 2-3 Statin Manager Main Menu...15 Figure 3-1 with One SIU Unit...19 Figure 3-2 Mdular Pwer Supply...20 Figure 3-3 Multiple SIU Units...22 Figure 3-4 Analg Input Mdules...23 Figure 3-5 Digital Input Mdules...24 Figure 3-6 Digital Output Mdules...25 Figure 3-7 Analg Output Mdule...26 Figure 3-8 Thermcuple Input Mdule...27 Figure 3-9 Tipping Bucket Rain Gauge...28 Figure 3-10 Recent Pwer Failure Dialg Bx...29 Figure 3-11 Pwer Failure Lg...29 Figure 3-12 Setup.exe File...34 Figure 3-13 Welcme Screen...34 Figure 3-14 License Agreement...35 Figure 3-15 Datalgger Type...35 Figure 3-16 Language Type...36 Figure 3-17 Statin Manager Installatin...36 Figure 3-18 Install SIU...37 Figure 3-19 Install Ram Disk...37 Figure 3-20 RAM Disk License Agreement...38 Figure 3-21 Install RAM Disk...38 Figure 3-22 Hardware Installatin Errr...39 Figure 3-23 Cnfigure RAM Disk...39 Figure 3-24 RAM Disk Cnfiguratin...40 Figure 3-25 Setup Cmplete...40 Figure 3-26 Initializatin Buttn...42 Figure 3-27 Initializatin Menu...43 Figure 3-28 Parameter Initializatin Table...44 Figure 3-29 Initialize Plling Screen...56 Figure 3-30 Initialize Statin...57 Figure 3-31 Initialize Cm Prts...58 Figure 3-32 Calibratin Schedules Table...59 Figure 3-33 Calibratin Schedules Table - Edit Mde...60 Figure 3-34 Calibratin Sequences Table...61 Figure 4-1 Main Menu Screen...63 Figure 4-2 Map Screen...64 Figure 4-3 Calibratin Menu...65 Figure 4-4 Initiate Calibratins Screen...66 Figure 4-5 Calibratin Sequence Dialg Bx...67 Figure 4-6 Manual Calibratins Dialg Bx...67 Figure 4-7 Instantaneus Data Display Screen...69 Figure 4-8 Calibratin Schedules Table...70 Figure 4-9 Calibratin Sequences Table...71 Figure 4-10 Calibratin System Menu...72 Figure 4-11 Surce Value Table...73 Figure 4-12 Calibratr Cmmands Table...74 Figure 4-13 Timer Cntrller Table...75 Figure 4-14 Example Table Defined fr Stream Switching...79 Figure 4-15 Example Table Defined fr Stream Switching

8 Figure 4-16 Example Table Defined fr Backflush...80 Figure 4-17 Example Table Defined fr Digital Input...81 Figure 4-18 Example Table Defined fr PM-10 Sampler...82 Figure 4-19 Manual Reprts Screen...82 Figure 4-20 Calibratin Cntrl Chart...83 Figure 4-21 Digital Input-Output Menu...84 Figure 4-22 Digital Output Lines Table...85 Figure 4-23 Digital Input Lines Screen...86 Figure 4-24 Digital Status Screen...87 Figure 4-25 Mark Dwn Channels Screen...88 Figure 4-26 Select Chart Screen...89 Figure 4-27 Initialize Pre-Defined Charts Screen...91 Figure 4-28 Vertical Strip Chart Screen...92 Figure 4-29 Hrizntal Strip Chart Screen...92 Figure 4-30 Select Calibratin...93 Figure 4-31 Start Calibratin Sequence while viewing a Strip Chart...94 Figure 4-32 Start Manual Calibratin while viewing a Strip Chart...95 Figure 4-33 User Chart Anntatin Hrizntal Strip Chart...95 Figure 4-34 User Chart Anntatin Vertical Strip Chart...96 Figure 4-35 Statin Lgbk Screen...98 Figure 4-36 Print Statin Lgbk Figure 4-37 Initializatin Menu Figure 4-38 Initialize Statin Screen Figure 4-39 Initialize Parameters Screen Figure 4-40 Initialize Plling Screen Figure 4-41 Initialize Reprts Menu Figure 4-42 Schedule Daily Printuts Screen Figure 4-43 Calibratin Cntrl Chart Limits Figure 4-44 Analg Output Table Figure 4-45 Quality Assurance Menu Screen Figure 4-46 Calibratin Cntrl Chart Figure 4-47 Exprt Data T Excel Figure 4-48 Exprt 15-Minute Data Figure 4-49 Statin Manager Data Menu Figure 4-50 Instantaneus Data Display Screen Figure 4-51 Tabular Displays Menu Figure Hur Averages Screen Figure Minute Averages Screen Figure Minute Averages Screen Figure Minute Averages Screen Figure 4-56 Real Time Data Figure 4-57 Scheduled Reprts Table Figure 4-58 Schedule Daily Printuts Screen Figure 4-59 Data Editr Figure 4-60 Alarm System Menu Figure 4-61 Parameter Alarm Table Figure 4-62 Parameter Definitins Table Figure 4-63 Alarm Update Table Figure 4-64 Relay Cnditin Table Figure 4-65 Alarm Telephne Table Figure 4-66 Digital Input Alarm Table Figure 4-67 Digital Input Message Table Figure 4-68 Alarm Histry Table Figure 4-69 Cnditin Flag Table Figure 4-70 Alarm Table Figure 4-71 Utilities Menu Screen

9 Figure 4-72 Security System Menu Figure 4-73 Define Grups Screen Figure 4-74 Define Permissins Table Figure 4-75 Define Screen Table Figure 4-76 Calculatr Screen Figure 4-77 Date and Time Screen Figure 4-78 Manual Data Backup Screen Figure 4-79 Main Pwer Failure Lg Screen

10 1.0 Intrductin This is the fr the EMC Statin Manager data lgger. It has been written t make initializatin, peratin and maintenance f the Statin Manager Data lgger easy fr new r experienced users. This manual cntains examples f the displays that actually appear n the screen f the Statin Manager Data lgger. Statin Manager Data lgger is an inherently user-friendly data lgger. It is quite easy t learn and perate. Mst cntrl and display actins are perfrmed with a single muse click n push buttns that appear n every screen. Learning t use the Statin Manager Data lgger is intuitive. Users will nly require a few minutes f practice t becme cnfident and cmfrtable in perating the many pwerful features and capabilities f this data lgger. This manual is divided int sectins t help the user understand the lgical rder f the Statin Manager Data lgger. Included is peratinal infrmatin abut the initializatin, setup, calibratin cntrls, printing data and displays, lgbk, and the many utility features that make up the Statin Manager Data lgger. A Trubleshting Guide is prvided t assist users with prblems that may ccur in the peratin f the data lgger. It als includes a Glssary, which defines the terms and nmenclature used in this manual. 9

11 Blank Page 10

12 2.0 General Infrmatin 2.1 Statin Manager Overview EMC Statin Manager data lggers can be used fr ambient air quality, CEMS, meterlgical, and water quality data lgging applicatins. This unique PC based data lgger ffers users many advanced data acquisitin and data management features and capabilities. An EMC Statin Manager Data lgger cnsists f tw basic cmpnents. The first is a PC, which has EMC Statin Manager Data lgger sftware, running Micrsft Windws XP, installed n it. The secnd is a Signal Interface Unit (SIU). The SIU is the hardware interface fr analg and digital input/utput signals frm analyzers r sensrs t the Statin Manager Data lgger. An SIU is a base-unit that accepts plug-in input/utput (I/O) mdules. The signal cable cnnectin between a Statin Manager PC and an SIU unit can be a standard RS-232C serial cable r a 2-wire, multi-drp, RS-485C cable, r an Ethernet LAN cnnectin. 2.2 Hardware Cnfiguratins Figure 2-1 shws a typical Statin Manager Data lgger cnfigured with ne SIU unit. One SIU unit will accept either 4 r 8 plug-in analg r digital I/O mdules. This cnfiguratin uses an RS-232C serial cable, r an Ethernet LAN cnnectin, between the Statin Manager Data lgger PC and the SIU unit. This is the standard cnfiguratin used in mst ambient air quality data lgging applicatins r CEMS installatins where the Statin Manager PC and an SIU unit are munted adjacent t each ther and nly fur I/O mdules are required. Mdem Printer RS-232C Cable 0 0 EMC SIU 0 PWR RUN TX RX GND INIT* COM Data+ Data- +Vs 8 AI 4 AO 8 Relay 8 DI V01 V02 V03 V04 V05 V06 V07 V08 A01 A02 A03 A04 R-1 R-2 R-3 R-4 R-5 R-6 R-7 R-8 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 0 Statin Manager PC Signal Interface Unit (SIU) Muse Figure 2-1 with 1 SIU Unit 11

13 Figure 2-2 illustrates a Statin Manager Data lgger PC cnfigured with fur SIU units. This cnfiguratin will permit up t 16 plug-in I/O mdules t be installed in ne Statin Manager Data lgger. SIU units cnfigured in this manner must be perated n an RS-485C data bus and require the installatin f an externally munted RS-232C t RS-485C. SIU units may be installed adjacent t the Statin Manager PC r they may be installed at lcatins separated by up t 1000 feet. This cnfiguratin can be used in plant envirnments where a Statin Manager Data lgger is cnfigured as a distributed data acquisitin system. The same type f cnfiguratin can als be used in an ambient mnitring statin r a CEMS installatin where the Statin Manager PC and multiple SIU units are munted adjacent t each ther. 0 RS485 RS232 0 EMC SIU 0 PWR RUN V01 TX V02 RX V03 V04 +Vs GND V05 INIT* V06 COM Data+ V07 Data- V08 8 AI 8 AI 8 AI 8 AI V01 V02 V03 V04 V05 V06 V07 V08 V01 V02 V03 V04 V05 V06 V07 V08 V01 V02 V03 V04 V05 V06 V07 V08 RS485 ID 0 RS-485C 0 RS485 PWR RUN TX RX +Vs GND INIT* COM Data+ Data- RS232 0 EMC SIU I/O 0 16 DI 16 DI 7 TC DI1 DI4 DI6 DI8 DI10 DI12 DI14 DI16 DI1 DI4 DI6 DI8 DI10 DI12 DI14 DI16 TC1 TC2 TC3 TC4 TC5 TC6 TC7 Spare Slt RS485 ID 0 RS-485C 0 RS485 RS232 0 EMC SIU 0 PWR RUN R-1 TX R-2 RX R-3 R-4 +Vs GND R-5 INIT* R-6 COM Data+ R-7 Data- R-8 8 Relay 8 Relay 8 Relay 8 Relay R-1 R-2 R-3 R-4 R-5 R-6 R-7 R-8 G R-1 R-2 R-3 R-4 R-5 R-6 R-7 R-8 R-1 R-2 R-3 R-4 R-5 R-6 R-7 R-8 RS485 ID 0 RS-232C RS-232C RS-485C Cnverter RS-485C 0 RS485 RS232 0 EMC SIU 0 PWR RUN TX A01 RX A02 +Vs GND INIT* A03 COM Data+ A04 Data- 4 AO 4 AO A01 A02 A03 A04 4 AO 4 AO A01 A02 A03 A04 A01 A02 A03 A04 RS485 ID 0 EMC Statin Manager PC 4 Signal Interface Units (SIU) Figure 2-2 with 4 SIU Units 12

14 2.3 Sftware EMC Statin Manager data lgger sftware has been written in C++ using the Micrsft Visual Studi Develpment Envirnment. Selected data lgger applicatins and quality assurance prgrams have been written in Micrsft Visual Basic t maintain cmpatibility with similar cmpatible applicatins n the EMC System Manager central data management system. The Statin Manager Data lgger ffers users a wide range f meaningful features and capabilities fr cllecting ambient air quality, CEMS, meterlgical, and water quality data. One f the unique features f Statin Manager Data lggers is an innvative graphical user interface and menu system. The menu system allws users t easily navigate thrugh the fllwing prgrams and ptins: Data display prgrams Trending r strip chart prgram Lgbk prgram Quality assurance Initializatin prgrams Alarms prgrams Data exprt prgrams 2.4 Cnventinal Data Lgger Operatin EMC Statin Manager Data lggers can be used t replace cnventinal stand-alne data lggers and strip chart recrders in air quality mnitring statins r in Cntinuus Emissin Mnitring System (CEMS) shelters. In ambient r CEMS peratin, the Statin Manager PC is usually lcated directly adjacent t the Statin Manager SIU r Rack Munt Interface Panel. SIU units can either be munted n DIN-rails in 19 equipment racks, panel-munted, r perated n a bench tp surface. The cnnectin between the SIU unit and the Statin Manager Data lgger PC can be either RS-485C r RS-232C, r an Ethernet LAN cnnectin. 2.5 Distributed Data Lgging Operatin An EMC Statin Manager Data lgger cnfigured with multiple SIU units can als be perated as a distributed data acquisitin system. In this type f peratin, the Statin Manager PC can be lcated in a central plant lcatin, such as a cntrl rm, and ne t fur SIU units can be installed at remte lcatins thrughut a plant. A 24 VDC pwer supply is used t pwer the SIU units at each site. In the distributed mde f peratin, the data cnnectin between the Statin Manager PC and the remte SIU units are made with a single, 2-wire, RS-485C data bus. The maximum distance pssible with the RS-485C prtcl is 1,000 feet. Distances up t 2,000 feet are pssible when an RS-485C repeater is used. 2.6 Input/Output Mdules SIU units accept a variety f standard plug-in input and utput (I/O) mdules. One SIU unit can accept frm ne t fur plug-in I/O mdules. Up t fur SIU units can be cnnected tgether n an RS-485C data bus t expand the number f I/O mdules that can be perated n ne Statin Manager Data lgger t a ttal f sixteen I/O plug-in mdule slts. The fllwing is a summary f the types f available I/O mdules and functins: 13

15 ADAM 5017 Analg Input Mdule: Each analg input mdule (up t fur per SIU) uses an A/D cnverter t cnvert sensr vltage and r current inputs t digital data. When prmpted by the Statin Manager sftware, the data is cnverted t engineering units and sent t the PC thrugh a standard RS-232 interface. The analg input mdules ffer superir prtectin frm grund lps and pwer surges fund with lder" hardware technlgy" data lggers. Each Analg Input mdule can handle up t 8- channel differential input that prvides prgrammable input ranges n all channels. Analg inputs accept vltage inputs (±1 V, ±5 V, ±10 V) and current inputs (0-20 ma and 4-20 ma). Since each mdule accepts 8 channels, a ttal 32 analg input channels can be mnitred with each SIU unit. In additin, Statin Manager can have eight calculated channels, prviding a ttal capacity f 40 data channels. ADAM 5052 Digital Input Mdule: The 5052 is a universal digital input/utput mdule that can be independently prgrammed fr each channel. Digital utputs are pen cllectr utputs which may be used t drive user-supplied relays t switch n heaters, pumps, valves r ther devices. The digital inputs can be either dry r wet cntacts. The 5052 mnitrs eight digital inputs with full independent islatin f 5000 V rms t prevent grund lps and t prevent damage frm pwer surges. Each SIU mdule can handle up t fur f these mdules. ADAM 5068 Relay Output Mdule: Each relay utput mdule ffers eight channels f Frm A relays fr cntrl f external devices. The cntact ratings are.5 A fr 120 VAC and 1 A fr 30 VDC. Relay Output Mdules can be installed in any available I/O mdule slt n any SIU unit that is cnnected t a Statin Manager Data lgger. ADAM 5024 Analg Output Mdule: The analg utput mdule prvides fur channels that are measured r calculated frm the Statin Manager. The frmat f the data is engineering units in a digital frm that is cnverted t an analg vltage r current by the Ranges are 0-20 ma, 4-20 ma r 0-10 VDC. Fur ADAM 5024 Analg Output Mdules will prvide a ttal f 16 analg utput channels n each Statin Manager Data lgger. Analg Output Mdules can be installed in any available I/O mdule slt n any SIU unit that is cnnected t a Statin Manager Data lgger. 2.7 Main Menu Figure 2-3 shws the Statin Manager Data lgger Main Menu screen. It illustrates the innvative graphical user interface available with the Statin Manager Data lgger. All f the display and selectin screens within the Statin Manager Data lgger incrprate a similar style that results in a clear and intuitive peratin fr the user. Cnflicting r cnfusing ptins are eliminated, allwing users t cncentrate n managing the mnitring statin and the data being cllected by the data lgger. Statin Manager Data lgger users quickly learn hw t navigate thrugh all f the screens and tables in the data lgger. A single click is all that is necessary t cause any actin r selectin t ccur. The Exit buttn n all screens is always lcated at the tp, right-hand crner f the screen. The interface is cnsistent and easy-t-learn. 14

16 Figure 2-3 Statin Manager Main Menu 2.8 Recmmended Statin Manager PC Hardware The fllwing are recmmended hardware specificatins fr EMC Statin Manager Data lggers. EMC nrmally supplies new Statin Manager Data lggers equipped with either a Gateway r Dell PC. Custmers may ptinally specify any ther data lgger brands r directly purchase the PC hardware themselves. EMC recmmends that Statin Manager PCs meet the fllwing minimum specificatins: 1.8 GHZ Intel Celern r Pentium prcessr 512 MB RAM memry 15 Clr VGA Mnitr 80 GB Hard Disk Drive 4 ea RS-232C Serial Prts 1 parallel printer prt Desktp r Micr-Twer Case HP Desk Jet Clr Printer r Equivalent 56 KB U.S. Rbtics External Mdem Micrsft Windws Small Business Editin (MS Wrd, Excel) Micrsft Windws XP Pr Whenever custmers perfrm the installatin f Statin Manager Data lgger sftware n a PC that they prvide, EMC recmmends that the custmer cntact EMC prir t any prcedures being dne. EMC recmmends that the hard disk drive f the Statin Manager PC be refrmatted accrding t the prcedures described in Sectin 3.4 f this manual. This prcedure will eliminate ptential cnflicts with nn-recmmended sftware prgrams and utilities that may be pre-installed n custmer prvided PC hardware. EMC Statin Manager Data lgger sftware will cnflict with cncurrent installatin f Micrsft Access database prgrams n the same PC. EMC therefre des nt recmmend that these prgrams be 15

17 installed n a Statin Manager Data lgger PC. EMC is nt respnsible fr any actins perfrmed withut EMC knwledge. The histry f the PC industry has demnstrated that the pwer and capabilities f the newest PC hardware will steadily increase ver time. PC hardware purchased by cnsumers tday and used fr Statin Manager Data lggers are very pwerful and will perate Statin Manager sftware extremely well. PC hardware available in the future will certainly be mre pwerful and prbably lwer in price. Althugh it may nt be necessary t upgrade the users Statin Manager data lgger PC hardware tday, users will always have the ptin t upgrade the PC hardware used t perate their licensed cpy f EMC Statin Manager data lgger sftware at any time in the future if they desire t d s. 16

18 Blank Page 17

19 3.0 Getting Started The fllwing sectin cntains detailed instructins fr starting up an EMC Statin Manager Data lgger. Users shuld read and understand the startup prcedures described in this sectin befre cntinuing with the installatin. EMC recmmends that users cmplete these steps in the fllwing rder: 3.1 Receive & Inspect Cmpnents 3.2 Cnnect Cmpnents Tgether 3.3 Switch On AC Pwer 3.4 Install Sftware 3.5 Initialize Data Lgger 3.6 Perfrm Acceptance Testing Receive & Inspect Cmpnents Prcedures 1. The Statin Manager data lgger will be received frm the factry packed in several shipping bxes. One f the bxes will cntain a Packing List detailing all f the cmpnents shipped in this rder and a list f specific cmpnents in each bx. 2. Unpack all bxes carefully and remve each cmpnent. Inspect the cmpnents fr bvius damage that may have ccurred during shipment. Reprt any suspected damage t the lcal freight carrier and EMC immediately. 3. Lcate the Packing List that dcuments all materials shipped. It will be attached t the utside f ne f the shipping bxes. 4. Immediately perfrm an inventry f all materials received and cmpare these against the enclsed EMC Packing List and the custmer s riginal purchase rder. 5. Retain shipping bxes fr at least 90 days in case a warranty return shipment is needed. 6. Cntact EMC Custmer Supprt at (805) if a discrepancy is nted between the Packing List and the cntents f the bxes r the purchase rder. 18

20 3.2 Cnnect Cmpnents Tgether Cnnecting PC Cmpnents and Peripherals Tgether 1. Place all f the hardware cmpnents f the Statin Manager data lgger n a clean, uncluttered wrkbench r wrking surface. 2. Lk at Figure 3-1 t understand hw the majr cmpnents f a Statin Manager data lgger are cnnected tgether. The cmpnents include the cmputer PC, mnitr, keybard, muse, mdem, printer, EMC Signal Interface Unit (SIU), EMC Mdular Pwer Supply, and cnnecting cables. 3. Lcate all f the PC hardware and cnnect them tgether. The PC hardware includes the PC, keybard, muse, and mnitr. Plug the PC cmpnents int their respective sckets n the rear f the PC. Plug in the AC pwer crds, but dn t turn n the pwer yet. 4. Lcate and cnnect the SIU t the PC. If nly ne SIU will be used, cnnect the male end f the supplied 6-ft lng DB-9 (9-pin) RS-232C serial cable int the COM 1 female serial prt n the rear f the PC. Cnnect the ther male end f this cable int the female RS- 232C serial prt n the left side f the Signal Interface Unit (SIU). If multiple SIU units will be used, g t Sectin and fllw the instructins fr cnnecting multiple SIU tgether n an RS-485C data bus. 5. Lcate the mdem cable and cnnect it t the rear f the PC. Plug the male DB-9 cnnectr end f the mdem cable int the female COM 2 serial prt n the rear f the cmputer PC. Plug the ther end f the mdem cable int the mdem. 6. Cnnect the printer cable int the DB-25 parallel prt r USB printer prt, n the rear f the Statin Manager PC if a printer will be installed. Cnnect the ther end f the printer cable t the printer. Plug the printer int the plug strip, but dn t turn n the AC pwer yet. Telephne Line Mdem Printer RS-232C Cable 0 0 EMC SIU +Vs GND INIT* COM Data+ Data- PW RUN R TX RX 8 AI 8 4 AO Relay 8 DI PC-033 PC-035 PC-041PC-038 V01 R-1 DI1 A01 A02 V02 V03 V04 V05 V06 V07 V08 A03 A04 R-2 R-3 R-4 R-5 R-6 R-7 R-8 DI2 DI3 DI4 DI5 DI6 DI7 DI8 0 0 Statin Manager PC Signal Interface Unit (SIU) Muse Figure 3-1 with One SIU Unit 19

21 3.2.2 Cnnect Mdular Pwer Supply t SIU Unit 1. Cnnect the SIU Pwer Supply t the SIU unit accrding t the wiring diagram shwn in Figure 3-2. The Mdular Pwer Supply includes an integral cable that is used fr cnnecting the 24 VDC pwer t the pwer input screw terminals n an SIU. 2. Verify that the AC line vltage where yu are lcated is the same vltage as that printed n the SIU Mdular Pwer Supply yu were supplied. The standard AC line vltage in the USA is 120 VAC. Other cuntries may be either 120 VAC r 240 VAC. If the AC line vltage marked n the SIU Pwer Supply Mdule is different than the AC line vltage where yu are lcated, d nt attempt t perate r plug it int the AC line pwer utlet. Please cntact EMC Custmer Supprt fr assistance. 3. Lcate and cnnect the psitive wire f the pwer supply cable (black with white dash marks) t the +V screw terminal n the SIU unit. Cnnect the negative wire f the cable (black) t the GND screw terminal n the SIU. Plug the Mdular Pwer Supply int the plug-strip. Dn t turn n the AC pwer yet. 4. SIU units are usually munted n 19 wide DIN-rails. They can als be munted n rack panels r n desktp surfaces. 0 EMC SIU 8 AI RS485 PWR RUN V01 TX V02 RX V03 V04 +Vs GND V05 Init* V06 Cm Data+ V07 Data- V08 16 DI D-2 D-4 D-6 D-8 D10 D12 D14 D16 8 Relay 8 Relay R-1 R-2 R-3 R-4 R-5 R-6 R-7 R-8 R-1 R-2 R-3 R-4 R-5 R-6 R-7 R-8 0 RS485 ID 0 24 VDC Pwer Supply + 24 VDC (Black - With White Dash Marks) (Black ) - 24 VDC Mdular Pwer Supply 120 VAC r 240 VAC Line Vltage Input Figure 3-2 Mdular Pwer Supply Cnnect Multiple SIU Units t ne Statin Manager PC 1. Use the fllwing prcedure t cnnect 2, 3, r 4 SIU units t ne Statin Manager PC. 2. Determine if mre than 4 I/O plug-in mdules will be installed in the Statin Manager data lgger. If mre than fur I/O mdules will be used, it will be necessary t install additinal SIU units. Up t fur SIU units can be cnnected t ne Statin Manager PC t prvide a maximum ttal f 20 Input/Output (I/O) mdule slts. 3. Cnnect multiple SIU units t the Statin Manage data lgger with a 2-wire, multi-drp RS- 485C data bus. 1, 2, 3, r 4 SIU units can be remtely lcated frm the Statin Manager PC n the 2-wire, multi-drp RS-485C data bus. 20

22 4. Use an RS-485C repeater device if the ttal distance frm the PC t the last SIU is a maximum f 1000 feet. See Figure 3-3 fr an illustratin f an RS-485C repeater device. 5. Physically lcate the multiple SIU units next t each ther in an ambient mnitring statin r CEMS shelter, r lcate the SIU units remtely in the manner described in this sectin. 6. Use the RS-232C serial cable supplied by EMC when nly ne SIU unit is cnnected t a Statin Manager data lgger. Refer t Figure 3-1 fr an example f a Statin Manager data lgger cnnected t ne SIU unit. 7. Munt the SIU units n 19 wide DIN-rails, rack panels, r desktp surfaces. 8. Observe that each SIU unit has tw DB9 cnnectrs that are labeled RS-485C. One f the RS-485C prts is a male cnnectr and the ther is a female cnnectr. Either ne f the RS-485C prts, r bth f them, can be cnnected t ther SIU units. 9. Nte that there is als a third RS-485C prt cnnectin n the tp f each SIU. This is a set f tw screw terminals that can be used fr cnnecting a 2-wire RS-485C signal cable. As with the DB-9 cnnectrs, the screw terminal RS-485C cnnectins can be used by themselves, r in cmbinatin with either f the tw DB-9 cnnectrs. 10. Cnnect the RS-485C data bus using a 2-wire, multi-drp cable. One f the tw wires is the plus (+) signal wire and the ther is the negative (-) signal wire. Observe in Figure 3-3 that all SIU units have the plus signal wires cnnected tgether and the negative signal wires cnnected tgether. 11. Nte that n DB-9 cnnectrs the plus signal wire is Pin 2 and the negative wire is Pin 3. A grund wire, r signal cable shielded cnnectin is nt used r required fr peratin f the RS-485C data bus. 12. Nrmally PCs are nly equipped with RS-232C serial prts. The RS-232C serial data signal n the COM1 prt must be cnverted t an RS-485C data signal with an RS-232C t RS-485C cnverter device (see Figure 3-3). 13. See Figure 3-3 n the fllwing page fr an illustratin f tw methds fr cnnecting multiple SIU units t a Statin Manager data lgger PC. 21

23 RS-232C Serial Cable RS-232C Serial Cable RS-232C t RS-485C Cnverter RS-232C t RS-485C Cnverter SIU 0 Data+ Data- 0 Data+ Data-. 0 SIU 0 Data+ Data- Data+ Data SIU 0 Data+ Data SIU 0 Data+ Data SIU 0 Data+ Data RS-485C Repeater / Extender 0 SIU 0 Data+ Data- 0 Data+ Data-.. 0 SIU 0 Data+ Data- 0 2-Wire, Multi-Drp RS-485C Data Bus 0 SIU 0 Data+ Data- 0 Figure 3-3 Multiple SIU Units 22

24 3.2.4 Cnnect Signal Wires t I/O Mdules The fllwing sectin illustrates hw t wire signal cnnectins t analg and digital I/O mdules that plug int SIU units. The types f available plug-in I/O mdules include analg input mdules, analg utput mdules, digital input mdules, digital utput mdules, in special cases can be cnfigured t handle Thermcuple input mdules. A drawing is prvided fr each type, which shws the signal terminals and wiring t external input r utput devices Cnnect Signal Wires t Analg Input Mdules 1. Use the fllwing infrmatin t cnfigure the signal wiring t Analg Input Mdules. After all signal wiring has been cmpleted, perfrm the initializatin f the analg inputs with the Initialize Parameters Table in the Statin Manager data lgger. 2. The ADAM 5017 mdule has 8 differential analg input channels. It is a lw sampling rate mdule with a 16-bit A/D cnverter. 3. Each analg input channel requires the cnnectin f 2 signal wires: a (+) signal and a grund (-) signal. The analg input mdules accept 0-1, 0-5, 0-10 VDC, r 0-20 and 4-20 ma input signals. 4. Typical signal wiring cnnectins fr vltage and current lp inputs are illustrated belw in Figure 3-4. Analyzer r Sensr 0-1, 0-5, 0-10 VDC + - Analyzer r Sensr 0-1, 0-5, 0-10 VDC RS485 RS232 0 Channel 1 Channel 9 8 AI 8 AI 8 DI 16 DI EMC SIU 0 PC-032 PC-033 PC-038 PC-039 PWR RUN RS485 V V0 +. Di0+ + Di0 - Di0- -+ TX Di1 V1 + RX - V1 + Di1+ Di2 - Di1- - Di3 V2 + - V2 + Di2+ + Di4 - - Di2- Di5 V3 + +Vs - V3 + Di3+ + Di6 - Di3- - Di7 GND V4 + - V4 + Di4+ + Di8 - Di4- - Di9 Init* V5 + - V5 + Di5+ + Di Cm Di5- Di11 ID Data+ V6 + - V6 + Di6+ + Di12 - Di6- - Di13 Data- V V7 + Di Di14 Di7- - Di15 0 Channel , 0-5, 0-10 VDC 0-20 r 4-20 ma Current Lp Signal Analyzer r Sensr Channel 16.. V hm Analyzer r Sensr Figure 3-4 Analg Input Mdules 23

25 Cnnect Signal Wires t Digital Input Mdules 1. Use the fllwing infrmatin t cnfigure the signal wiring t Digital Input Mdules. After all signal wiring has been cmpleted, perfrm the initializatin f the digital inputs with the Digital Input Table in the Statin Manager data lgger. 2. The ADAM 5052 mdule has 8 ptically islated digital input channels. The ptically islated digital inputs n this mdule will detect a digital status cnditin when a vltage in the range f 3 t 32 VDC is applied t a digital input channel. The signal terminatins n the mdule have tw signal wire terminals fr each digital input channel. One terminal is the (+) signal and the secnd terminal is the grund r negative (-) signal. 3. Figure 3-5 illustrates typical digital input signal wiring cnnectins. 0 8 AI EMC SIU 0 RS485 PWR RUN V0 + - TX V1 + RX - V Vs V3 + - GND V4 + - Init* V5 + RS232 Cm - Data+ V Data- V AI V0 + - V1 + - V2 + - V3 + - V4 + - V5 + - V6 + - V7 + - Channel 8 Digital Input Signal Channel 1 8 DI Di0+ 0 Di1+ 1 Di D+ Di5- - Di VDC DI Di0 Di1 Di2 Di3 Di4 Di5 Di6 Di7 Di8 Di9 Di10 Di11 Di12 Di13 Di14+ Di15 Channel 9 RS485 ID VDC Digital Input Signal Figure 3-5 Digital Input Mdules Cnnect Signal Wires t Digital Output Mdules 1. Use the fllwing infrmatin t cnnect signal wiring t Digital Output Mdules. After all signal wiring has been cmpleted, perfrm the initializatin f the analg inputs with the Digital Output Table in the Statin Manager data lgger. 2. The ADAM 5068 digital utput mdules have 8 relay utputs and are used t cntrl calibratrs and switch slenid valves. 3. Signal terminatins n the 5068 mdules have tw signal wire terminals fr each digital relay utput channel. The letters NO designate Nrmally Open and the letters Cm designate Signal Cmmn. 24

26 4. Figure 3-6 illustrates typical digital utput wiring cnnectins fr the digital utput mdules. Calibratr r Slenid Valve Cntact Clsure 0 EMC SIU 0 RS485 PWR RUN V0 V1 TX V2 RX V3 V4 V5 V6 +Vs V7 V8 GND V9 Init* V10 RS232 V11 Cm V12 Data+ V13 0 Data- V14 + V15 8 AI 8 AO 8 DI 8 Relay... Channel 1 RS485 V01 + NO 0 NO 0 - Cm Cm V02 + NO 1 NO 1 - Cm Cm V03 + NO-2 NO-2 - Cm Cm V04 + NO 3 NO 3 - Cm Cm V NO 4 NO 4 Cm Cm V NO 5 NO 5 Cm Cm ID V NO 6 Cm V NO Cm 0 Channel 8 Cntact Clsure Calibratr r Slenid Valve Figure 3-6 Digital Output Mdules Cnnect Signal Wires t Analg Output Mdules 1. Use the fllwing infrmatin t cnnect signal wiring t Analg Output Mdules. After all signal wiring has been cmpleted, perfrm the initializatin f the analg inputs with the Analg Output Table in the Statin Manager data lgger. 2. Analg utput channels can be any calculated r directly measured data parameter recrded by the Statin Manager data lgger. 3. The analg utput mdule has tw sets f signal terminals with 4 channels n each set fr a ttal f 8 analg utput channels. 4. The first set f terminals fr each f the 4-channel analg utput channels. The first set f 25

27 terminals is current utput terminals (0-20 r 4-20 ma). These terminals are labeled I0 +, I1+, I2+ I3+ and I0, I1-, I2-, I3- respectively. Since these current lp signals are nt islated signals, EMC recmmends using a separate signal islatr mdule t islate the current lp utput signals frm external circuits. 5. The secnd set f terminals is vltage utput terminals (0-10 VDC). These terminals are labeled V0+, V1+, V2+, V3+ and V0, V1-, V2-, V3- respectively. Since these vltage signals are nt islated signals, EMC recmmends using a separate signal islatr mdule t islate the vltage utput signals frm external circuits. 6. Figure 3-7 illustrates typical signal wiring cnnectins fr the analg utput mdule. 0 8 DI EMC SIU 0 RS485 PWR V0 RUN V1 TX V2 RX V3 V4 V5 V6 +Vs V7 V8 GND V9 Init* V10 RS232 V11 Cm V12 Data+ V13 0 Data- V14 + V15 8 AI Channel 1 4 AO 8 Relay. V01 + I0+ NO 0 - I0- Cm V02 + I1+ NO 1 - I1- Cm V03 + I2+ NO-2 - I2- Cm V04 + I3+ NO 3 - I3- Cm V05 + V0+ - V0- NO 4 Cm V06 + V1+ - NO 5 V1- Cm V07 + V2+ NO 6 - V2- Cm V08 + V3+.. NO V3- Cm Channel 8 DCS r SCADA 0-20 r 4-20 ma r 4-20 ma DCS r SCADA RS485 ID 0 Figure 3-7 Analg Output Mdule Cnnect Thermcuple Signal Wires t Thermcuple Input Mdules 1. Use the fllwing infrmatin t cnnect signal wiring t Thermcuple Mdules. After all signal wiring has been cmpleted, perfrm the initializatin f the analg inputs with the Parameter Initializatin Table in the Statin Manager data lgger. 2. The ADAM 5018 Thermcuple mdule has 7 differential thermcuple input channels that can accept Type J, K, T, E, R, S, and B Thermcuples. 3. Each Thermcuple input channel n the Thermcuple mdule has 2 input terminals: the (+) signal and a grund (-) signal terminal. 4. Figure 3-8 illustrates typical wiring cnnectins fr a Thermcuple mdule. 26

28 Type J, K, T, E, R, S r B Thermcuple DI EMC SIU 0 RS485 PWR V0 RUN V1 TX V2 RX V3 V4 V5 V6 +Vs V7 V8 GND V9 Init* V10 RS232 V11 Cm V12 Data+ V13 0 Data- V14 + V15 8 AI V01 + V0+ - V0- V02 + V1+ - V1- V03 + V2+ - V2- V04 + V3+ - V3- V05 + V4+ - V4- V06 + V5+ - V5- V07 + V6+ - V6- V CJC+ CJC- Channel 1 7 T/C 8 Relay. NO 0 Cm NO 1 Cm NO-2 Cm NO Cm 3 NO 4 Cm NO 5 Cm NO 6 Cm NO 7 + Cm RS485 ID 0 Figure 3-8 Thermcuple Input Mdule Cnnect Signal Wires t Tipping Bucket Rain Gauge 1. Use the fllwing infrmatin t cnnect signal wiring t a tipping bucket rain gauge. Either befre, r after all signal wiring has been cmpleted, perfrm the initializatin f the analg inputs with the Parameter Initializatin Table in the Statin Manager data lgger. 2. The tipping bucket rain gauge cnnects t any channel n an Analg Input Mdule. The channel number used fr rainfall mnitring is selected in the Statin Manager Parameter Initializatin Table. 4. A tipping bucket rain gauge has tw signal cntact-clsure terminals. Cnnect the signal wires t the 1.0 micrfarad capacity, 2.0 mega hm resistr, and the 5 VDC pwer supply accrding t the wiring diagram shwn belw in Figure

29 Tipping Bucket Rain Gauge 0 8 DI EMC SIU 0 RS485 PWR RUN V0 V1 TX V2 RX V3 V4 V5 V6 +Vs V7 V8 GND V9 Init* V10 RS232 Cm V11 V12 Data+ V13 0 Data- V14 + V15 8 AI V V V V V V V V RS485 ID ufd 2 meghm 115 VAC 5 VDC Pwer Supply - + Figure 3-9 Tipping Bucket Rain Gauge 28

30 3.3 PC Startup Switch On AC Pwer 1. After the previus steps have been cmpleted and it has been verified that the cables have been plugged in crrectly, the AC pwer can be actuated n the PC, vide mnitr, the printer, and the mdem. 2. EMC Statin Manager data lggers will autmatically bt up after a pwer failure and autmatically begin cllecting data. The Statin Manager data lgger is designed t run cntinuusly, and withut peratr interventin after pwer is restred fllwing a pwer failure. 3. When users lg in t the Statin Manager data lgger after a pwer failure r restart, it will display the Recent Pwer Failure dialg bx shwn in Figure This dialg bx ntifies the user that a pwer failure has ccurred and prmpts the user t acknwledge the pwer failure. The Pwer Failure Prgram recrds the time and duratin f the pwer failure and the persn s initials that acknwledged the pwer failure in the Statin Manager Pwer Failure Lg in Figure Figure 3-10 Recent Pwer Failure Dialg Bx Figure 3-11 Pwer Failure Lg 29

31 3.3.2 Startup Statin Manager Sftware 1. After the AC Pwer has been switched n, Micrsft Windws will bt up and the EMC Statin Manager Data lgger sftware will autmatically startup. 2. The first screen n the vide terminal will be the Statin Manager Data lgger Main Menu. 3. Immediately after this screen is displayed, a dialg bx will appear n tp f it that prmpts the user t enter a passwrd Default Passwrd 1. Each time the Statin Manager sftware starts up, a valid passwrd must be entered t gain access t the screens and functins f the Statin Manager Data lgger. 2. The first time the Statin Manager Data lgger is started up, use the default passwrd EMCEMC. The default passwrd is: EMCEMC. 3. After the user r System Administratr has becme familiar with the security system and the methds f entering new passwrds and permissins, the security permissins and new passwrds shuld be mdified t fit the user s requirements. 4. When the user is ready t enter new passwrds and permissins, d the fllwing: a. Click n the security sub-menu n the Utilities Menu screen t bring up the Security submenu. b. Use the screens in this sub-menu t mdify r enter new passwrds, r assign permissins t users fr any screen display r editing functin in the Statin Manager data lgger. c. The default passwrd EMCEMC will cntinue t be used until such time as the System Administratr r an authrized user changes it t a different passwrd. d. Users shuld refer t the prcedures utlined in Sectin f this Manual fr detailed infrmatin abut the security passwrd system in the Statin Manager data lgger and the prcedures t mdify r change passwrds. e. It is recmmended t cntact EMC befre attempting t change any passwrds. EMC is nt respnsible fr any issues that may arise if this is dne withut EMC s knwledge. 3.4 Install Sftware The first step in this sectin is t determine whether r nt the installatin f Micrsft Windws and EMC Statin Manager Data lgger sftware will be required. 1. D Nt Install Sftware - If EMC supplies the PC. 30

32 Whenever EMC prvides the Statin Manager PC, it will nt be necessary fr the user t install Micrsft Windws r Statin Manager Data lgger sftware. The EMC factry will have already installed this sftware. If EMC has supplied the Statin Manager PC, the user shuld skip this sectin and g t Sectin 3.5 and begin t initialize the Statin Manager Data lgger. 2. User Install Sftware - If the user supplies the PC. DO NOT INSTALL the EMC Sftware n any PC befre cnsulting with EMC. Whenever the user supplies the Statin Manager PC, it will be necessary fr the user t re-frmat the hard drive, re-install Micrsft Windws XP, and install EMC Statin Manager Data lgger sftware. If the user supplies the PC, cmplete the steps in Sectins & Re-Install Windws XP A re-frmat f the PC hard disk is always required when the user supplies the Statin Manager PC and perfrms the installatin f EMC Statin Manager Data lgger sftware. A re-frmat is nt required when EMC prvides the Statin Manager PC. NOTE: A RE-FORMAT IS NOT RECOMMENDED WITHOUT CONSULTING EMC FIRST! Be advised that if this PC has imprtant data currently n it, yu will LOSE ALL yur previus data. 1. Insert the Windws XP CD-ROM int yur CD-ROM drive and then restart the cmputer. NOTE: T start yur cmputer frm the Windws XP CD-ROM yur cmputer must be cnfigured t start frm the CD-ROM drive. In sme cases, yu may have t mdify yur cmputer's BIOS settings t d this. 2. At the Welcme t Setup page, press ENTER t cntinue. 3. Press F8 t accept the Windws XP Licensing Agreement. 4. If an existing Windws XP installatin is detected, yu are prmpted t repair it. Press ESC (DO NOT REPAIR). 5. All existing partitins and unpartitined spaces are listed fr each physical hard disk. Using the arrw keys select each partitin and delete them all by pressing D. Yu shuld end up with nly end up with ne unpartitined space. NOTE: If yu press D t delete an existing partitin, yu must then press L (r press ENTER, and then press L if it is the System partitin) t cnfirm that yu want t delete the partitin. Repeat this prcess fr each f the existing partitins that yu want t use fr the new partitin. 6. T install Windws XP, select the unpartitined space and then press ENTER. 7. Select the frmat ptin Frmat the partitin by using the NTFS file system, and then press ENTER. 8. After Setup frmats the partitin, fllw the n-screen instructins t cntinue Setup until Windws XP fully installs Change Micrsft Windws Settings Several Micrsft Windws settings must be changed fr prper Statin Manager Data lgger peratin. These changes can be made frm the Windws Cntrl Panel. T pen the Cntrl Panel, press Start in the Task Bar, select Settings, and click n Cntrl Panel Display 31

33 Check the fllwing Micrsft Windws settings and change if needed: 1. The Statin Manager Data lgger is designed t run at 640x480 reslutin. T adjust the PC t this reslutin, find the Display icn in the Cntrl Panel and duble click. Select the Settings tab and lk fr a bx titled Screen area. If the area is nt 640x480 (i.e. 800x600) then adjust it 640x480 and press Apply. Windws will resize yur screen autmatically and yu must press Yes t accept the setting change. 2. The Statin Manager Data lgger is nt cmpatible with the use f screen savers. D nt attempt t use screen savers with the Statin Manager Data lgger. 3. T disable screen savers, find the Display icn in the Cntrl Panel and duble click. Select the Screen Saver tab and ensure that Nne appears under Screen Saver Pwer Management Micrsft Windws Pwer Management is designed t save energy and will autmatically turn ff yur hard drive after a certain amunt f inactivity. Statin Manager Data lggers will nt wrk prperly with this feature enabled. The Pwer Management feature MUST be disabled! Lcate the Pwer Optins icn in the Cntrl Panel and duble click n this icn. Find the ptin named Turn ff hard disks and select Never frm the pull dwn menu. Press Apply and then OK t save changes. Users can use the vide mnitr pwer management system n their vide mnitr. This is ptinal and will nt affect the peratin f Statin Manager Data lgger Date/Time Micrsft Windws autmatically adjusts the time fr daylight savings. Statin Manager Data lggers will nt functin prperly with this feature enabled therefre MUST remain in Pacific Standard Time, PST. 1. THE Daylight Savings FEATURE MUST BE DISABLED!!! 2. Find and duble click the Date/Time icn in the bttm right hand crner f the Task Bar. 3. Select the Time Zne tab and ensure Autmatically adjust clck fr daylight saving changes is nt checked. 4. Press Apply then OK t save and exit Install Sftware This sectin prvides instructins fr the installatin f EMC Statin Manager Data lgger sftware n the Statin Manager PC using the EMC supplied CD-ROM media. This prcedure invlves the installatin f tw separate prgrams. The first is the installatin f an SIU Utility Prgram. This prgram is used fr cnfiguring and calibrating the Signal Interface Unit. The secnd prgram is the EMC Statin Manager Data lgger sftware. Bth f these sftware prgrams are prvided n the EMC Statin Manager Data lgger CD-ROM media. 32

34 SIU Utility Sftware Installatin Fllw these step-by-step instructins t install the SIU Utility file int a hard drive directry f the Statin Manager Data lgger PC, and t initialize and lad the SIU Utility sftware. 1. Clse dwn any applicatins running in the taskbar. This can be dne by right clicking n the applicatin icn in the taskbar fllwed by a left click n Clse. 2. Insert the Statin Manager Data lgger Setup CD and pen the CD-ROM Drive. 3. Lcate the ADAM Utility Flder with respect t the SIU supplied with the Statin Manager Data Lgger. This shuld be either the Serial SIU r the TCP/IP SIU and in sme cases the 4017 SIU. 4. Launch the install file and fllw the prmpts using all the defaults selected. 5. The utility files will be installed fllwed by the message Advantech Adam Utility Setup was cmpleted successfully. Select OK t exit setup and installatin is cmplete Statin Manager Sftware Installatin Please review all the fllwing steps t perfrm the installatin f EMC Statin Manager Data lgger sftware befre cntinuing: 1. First, make sure that the PC is set up t aut rebt upn a pwer failure which is set in the BIOS. 2. Change the CD-ROM drive letter frm D:\ t any letter, typically E:\. T d this, g in t the Start Menu -> Cntrl Panel -> Administrative Tls -> Cmputer Management -> Right click n the CD-ROM Drive and select change drive letter. 3. Once the drive letter is changed, insert the Statin Manager Data lgger Setup CD int the CD-ROM drive. 4. Run the Setup.exe in the Default Statin Manager Installatin Flder. Figure

35 Figure 3-12 Setup.exe File 5. Upn the startup f the Statin Manager Setup prcess Windws Install Wizard will prmpt the user t acknwledge that Statin Manager is abut t be installed. Click Next. Figure 3-13 Figure 3-13 Welcme Screen 34

36 6. The fllwing screen displays the sftware license fr EMC Statin Manager Sftware. Click Accept t cntinue. Figure 3-14 Figure 3-14 License Agreement 7. The user will then be prmpted t select the type f Installatin desired. Always select Install- Statin Manager Ambient Datalgger unless specifically instructed t d therwise by EMC. Figure 3-15 Figure 3-15 Datalgger Type 8. Select the English versin f the installatin. Figure

37 Figure 3-16 Language Type 9. EMC Statin Manager Sftware will nw be installed. Figure 3-17 Figure 3-17 Statin Manager Installatin 10. Upn cmpletin f the Statin Manager Setup, the user will be prmpted t select the cmmunicatin device being used t cllect data. Always select Advantech SIU unless specifically instructed t d therwise by EMC. Figure

38 Figure 3-18 Install SIU 11. Once the SIU has been installed, a new screen will prmpt the user t install the RAM Disk. Figure 3-19 Figure 3-19 Install Ram Disk 12. The user will then be prmpted t accept the license agreement fr the RAM Disk sftware. Figure

39 Figure 3-20 RAM Disk License Agreement 13. After the License Agreement, the user will be prmpted t install the RAM Disk sftware. Figure 3-21 Figure 3-21 Install RAM Disk 14. A Hardware Installatin windw will pp up stating that The hardware has nt passed Windws Lg testing. When this prmpt appears, click Cntinue Anyway. Figure

40 Figure 3-22 Hardware Installatin Errr 15. Once the RAM Disk Sftware has been installed, it will prmpt the user t cnfigure the RAM Disk. Click Finish t cnfigure the RAM Disk. Figure 3-23 Figure 3-23 Cnfigure RAM Disk 16. When the RAM Drive Settings screen appears, make sure the Enable RAM Disk is checked, select D:\ fr the Driver Letter, leave the Startup Type as Autmatic and select Emulate a lcal hard disk as the Operating Mde. Figure

41 Figure 3-24 RAM Disk Cnfiguratin 17. Once the setup is cmplete, restart the cmputer. Figure 3-25 Figure 3-25 Setup Cmplete 18. After restarting the PC, clse all applicatins running in the task bar. 19. Open the Statin Manager Install CD and lcate the Updates Flder. 40

42 20. Cpy all the files in the Setup Flder and SM Flder in t the respective flders n the C:\ drive. i.e. Frm the Setup Flder in the Updates Flder, cpy all the files t the C:\Setup Flder. 21. Frm the Updates Flder, lcate the Windws Flder. In the Windws Flder, cpy the respective Statman ambient.ini r the Statman cem.ini file t the C:\Windws flder, depending n which system the user requires. Change the current statman.ini file name t a different ne, i.e. Statman1.ini. Then change the Statman ambient.ini file t statman.ini. 22. Lcate the System32 Flder in the Updates\Windws Flder and cpy the syslg.dll file in t the C:\Windws\System32 Flder. 23. Once all the files have been cpied frm the Updates Flder, restart the cmputer and let everything take effect Upgrades Sftware upgrades are cntained n CD-ROM and include a cmplete new set f the EMC Statin Manager Data lgger sftware. A sftware versin number is assigned t each upgrade CD-ROM versin release. EMC will assist yu via the telephne, if necessary during the sftware upgrade. All upgrades must be dne either via a call ut service r via the telephne with an EMC technician. NOTE: EMC is NOT liable fr any upgrades perfrmed withut EMC assistance. A sftware upgrade CD-ROM can cntain crrectins t sftware prblems and ther enhancements t Statin Manager Data lgger sftware. New features and capabilities can als be included n a sftware upgrade CD-ROM. 3.5 Initialize This sectin prvides step-by-step prcedures fr initializing a Statin Manager Data lgger Intrductin 1. Initializatins are the setup files and tables, which represent the unique persnality f each Statin Manager Data lgger. Initializatins are cmprised f apprximately eighty disk files and tables stred in the Setup directry lcated n the hard disk f the Statin Manager data lgger. 2. When a Statin Manager Data lgger is initialized, the primary statin name entered fr the plling name becmes the directry name fr that set f initializatins. Fr example, if the statin name were Wdward, the initializatins fr that Statin Manager Data lgger wuld be called Wdward. 3. When a Statin Manager Data lgger is received by a custmer, it will cntain tw sets f generic initializatins. One f these is called Ambient and the ther is called CEMS. After the Statin Manager Data lgger has been started, the user can chse t use and edit either f these pre-installed Ambient r CEMS initializatins, r create a ttally new set f initializatins that is specific fr the user s mnitring statin. 4. Initializing a Statin Manager data lgger requires the cmpletin f the fllwing steps: Select Initializatin Menu, Initialize Statin, & Initialize Plling. Enter Primary Statin Name. 41

43 Select Initialize Parameters. Edit fr the mnitring statin requirements. Select and edit the Initialize Statin and the Initialize Averaging screens. Select and edit the Initialize Cm Prts screen and attach the mdem(s). Re-start the cmputer t begin cllecting data. 5. It wuld be helpful fr the user t read Sectins and beynd befre prceeding with actual steps f initializing a Statin Manager Data lgger Initialize a Press the Initializatin buttn n the Main Menu t begin the steps f initializing a Statin Manager Data lgger. This will bring up the Initializatin Menu, which prvides access t all f the selectin screens and tables needed t initialize and startup a Statin Manager Data lgger. Figure 3-26 Figure 3-26 Initializatin Buttn Initializatin Menu The Initializatin Menu has six selectins that are used fr initializing a Statin Manager Data lgger. It wuld be helpful fr the user t click n each buttn n this screen, ne at a time, and view the different screens that are available. This can help the user becme familiar with the screens and related terms befre prceeding with the actual steps f initializing a Statin Manager Data lgger. Figure

44 Parameter Initializatin Table Figure 3-27 Initializatin Menu The first step in setting up and creating new initializatins fr a Statin Manager Data lgger is t make entries int the Parameter Initializatin table. Select Initialize Statin frm the Initializatin Menu, and then select Initialize Parameters. Figure

45 Figure 3-28 Parameter Initializatin Table 1. The fllwing sectin describes the Initialize Parameters table and the prcedures fr entering new data r editing existing data. a. This table is used t initialize all data channels recrded by the Statin Manager data lgger, including bth analg input channels and calculated channels. b. T edit this table, select the Edit Table buttn at the bttm f the table. Clicking n this buttn will cause the bttm half f the table t change int the Edit Mde wrk regin. 2. The fllwing describes the Edit Mde wrk regin and prcedures fr editing data r making new entries int this table. a. The editing methds used t edit the Initialize Parameters table are identical t thse used in all ther tables in the Statin Manager data lgger, a Reginal Manager data management system, r System Manager central data management system. After the user has learned these prcedures, the user will understand hw t edit all ther tables. b. When the Edit Mde wrk regin first appears, it will have blank entries in all f the 13 fields shwn. This is the nrmal starting pint fr users when entering new data int a blank, uncnfigured Initialize Parameters table. Even when entries have already been made int the Initialize Parameters table, the user will still use the Edit Mde wrk regin t add additinal lines f channel cnfiguratin data t the table. c. The Edit Mde wrk regin is used t edit existing lines f initializatin data in the table as well as make new entries. d. T edit a line f data in the table, click anywhere n any line in the bdy f this table. This will cause that line f data t be highlighted and entered int the Edit Mde wrk regin. When the line f data selected is highlighted, it indicates that the infrmatin n that line als appears in the Edit Mde wrk regin and can nw be edited by the user. e. A secnd methd f editing data in this table can be perfrmed by the user. This is dne by clicking the Edit Line buttn at the tp f the Edit Mde wrk regin. When the Edit Line buttn is pressed, a dialg bx appears that prmpts the user t select a line t be edited in the Initialize Parameters table. The use f the Edit Line buttn is functinally identical t the prcedure described in d abve, where the user clicks n a line in the bdy f the Initialize Parameters table. f. The user can select and edit any f the fields in the line f data retrieved frm the Initialize Parameters table by clicking n the buttn abve that field in the Edit Mde wrk regin. h. If the user clicks n the Parameter buttn in the Edit Mde wrk regin while entering new data, r editing existing data, a scrllable pull-dwn list f parameters will appear underneath that field. Clicking n the scrll buttns at the edge f this pull-dwn list will permit the user t view the entire list f parameters cnfigured n the Statin Manager data lgger. i. On the bttm f the Parameter pull-dwn list are tw buttns. The first is Add and the secnd is Del. The Add is used t add a new parameter name that desn t 44

46 currently exist in the parameter list. The Del is used t delete a parameter name that currently exists in the parameter list. The user may use any f the pre-cnfigured names, r delete any f the parameter names shwn and add new nes. Parameter names can be any cmbinatin f up t five alphanumeric characters. j. Sme fields in varius Statin Manager data lgger tables have Add r Del buttns at the bttm f their pull-dwn lists. When these add r delete buttns are pressed, a dialg bx appears that require users t make keybard entries. Other dialg bxes permit the user t make chices frm scrllable lists f data. k. After a selectin has been made in the parameter list, the next field in the table, the Averaging Methd pull-dwn list will appear. This is a list f averaging methds available n a Statin Manager data lgger. l. As the user cmpletes entries int each field, a pull-dwn list in the next field t the right f it will appear. New data is entered int the table ne field at a time, frm left t right. Once all data has been entered r edited, press the Save Line buttn t save the changes. m. The New Entry buttn n the Edit Mde wrk regin is used t insert a line f data at any lcatin in the table. This permits the user t rganize the entries any way they wish. n. When the Delete Line buttn is pressed, a dialg bx will appear that prmpts the user t select a line in the bdy f the Initialize Parameters table. If the user selects a line in the table t delete, a secnd dialg bx will appear that asks the user t cnfirm (Yes r N) that the line selected is t be deleted. If the user indicates Yes, that line will be deleted frm the Initialize Parameters table.. The buttns n the tp rw f the Edit Mde wrk regin are used fr new entries r clse the Edit Mde wrk regin withut perfrming any editing activity. 3. The user can create new parameter names f up t 5 characters in the Initialize Parameter table, edit existing parameter names, r delete any parameters names in the list f parameter names. 4. The fllwing are the channel cnfiguratin capabilities f Statin Manager data lggers. a. Statin Manager data lggers can be initialized fr a maximum ttal f 40 data channels. b. The minimum cnfiguratin f Statin Manager data lggers is 8 differential analg input channels. This can be increased in increments f 8 analg input channels t a maximum f 32 differential analg input channels by using additinal analg plug-in mdules. c. Statin Manager data lggers can be cnfigured t recrd an additinal 8 calculated data channels if 32 analg input channels are installed. The maximum number f initialized data channels, including bth analg input channels and calculated channels is The user can select a variety f averaging methds fr any data channel. The methds include: standard arithmetic averaging f 1-secnd samples, wind speed and directin vectr averaging, scalar wind speed and directin, vertical wind speed, sigma, sigma theta, sigma w, sigma v, rainfall, cefficient f haze (COH), difference between tw channels, sum f tw channels, rati f tw channels, lbs/hr, ppm-dry-crrected, 45

47 vlumetric stack flw, and % efficiency. 6. The user may create Dummy r Phantm channels. Users may have special requirements t create Dummy channels as place markers in the serial streams f data that are sent t plling systems ther than EMC s System Manager. These systems may include ESC central plling systems and thers. Dummy channels can be identical t any ther analg input, r calculated channel, except that the user may nt wish t retain data frm these channels. T create a Dummy channel, the user shuld select an apprpriate name and initialize it in the same manner as they wuld any ther channel, whether analg input, r calculated. In rder t cnserve the number f analg input channels used, Dummy data channels shuld be created as calculated channels. Examples f fictitius Dummy channels culd include calculated channels, such as difference between tw channels, sigma calculatin, r thers. The user has the ptin t select the averaging intervals f data frm Dummy channels. The prcedure fr selecting the averaging intervals fr each parameter is fund in Sectin The next field in the Initialize Parameters table lists the input channel type. Only tw types f input channels can be listed here. The first type is calculated channels, and the secnd type is analg input channels. Any averaged data channel that directly receives its input data frm an analg input has the crrespnding analg input channel number listed in this field. This can be a number between 01 and 32, and crrespnds t the analg input channel number n the analg input PC bard. If the averaged channel is a calculated type that is a calculatin derived frm ther analg input channels r surces, the letters calc will appear in this field. 8. The user can easily specify where the decimal pint will appear in the data that is stred n Statin Manager data lgger. This is perfrmed by clicking the Data Frmat buttn in the Edit Mde wrk regin. A pull-dwn list displays the pssible chices f where the decimal pint will appear in all data stred fr that data channel. 9. Users can select the pre-cnfigured unit labels by clicking n the Units buttn in the Edit Mde wrk regin. A pull-dwn list shws the units that have been pre-cnfigured. Users can edit, delete, r add new unit names with the Add and Del buttns at the bttm f the pull-dwn list. 10. The full-scale value f each recrded data channel may be selected by clicking the fullscale buttn. The full-scale value is equivalent t the m cmpnent in the slpe and intercept equatin: y=mx+b. The value entered shuld be the same as the full-scale range f that data channel in engineering units. When this buttn is selected, a pull-dwn list will shw a range f pre-cnfigured full-scale values. The user may edit, delete, r add new values in the list. 11. The zer value f each recrded data channel may be selected by clicking the Zer buttn. The zer value is equivalent t the b cmpnent f the scaling equatin: y=mx+b. The value entered shuld be the same as the zer range f that data channel in engineering units. As an example, if a temperature sensr data channel had a range f - 20 C t +70 C, the full scale engineering units value wuld be +70, and the zer engineering units value wuld be -20. When the Zer buttn is selected, a pull-dwn list will shw a range f pre-cnfigured full-scale values. The user may edit, delete, r add new values with the Add and Del buttns. 12. The Max. Value is the a user selectable value, r level in engineering units at, r abve which Statin Manager data lgger will flag data with an Invalid flag. When this buttn is clicked, a pull-dwn list f values will appear. The pull-dwn list shws the values that have been pre-cnfigured with Statin Manager data lgger. The user can edit, delete, r add new values with the Add and Del buttns at the bttm f the scrllable pull-dwn list. 46

48 13. The Min. Value is the a user selectable value, r level in engineering units at, r belw which Statin Manager data lgger will flag data with an Invalid flag. When this buttn is clicked, a pull-dwn list f values will appear. The pull-dwn list shws the values that have been pre-cnfigured with Statin Manager data lgger. The user can easily edit these values, delete, r add new values with the Add and Del buttns at the bttm f the scrllable pull-dwn list. 14. The F.S. Vlts field is used fr sftware selectin f the full scale input vltage fr each analg input channel. The available chices are 1v, 5v, and 10v. These may be independently selected fr each analg input channel. 15. There are tw Min Samples fields that are used t independently set the criteria fr minimum number f valid samples fr 1-minute averages and 1-hur averages. Clicking n the either buttn will display a scrllable list f numbers t select the applicable minimum samples criteria. If the number f valid data samples by Statin Manager fr each data channel is less than the 1 Minute r 1 Hur criteria specified by the user, the averaged data will be flagged as invalid. 16. The Rate f Change field is used t flag data that change in magnitude frm ne 1- Secnd data sample t the next 1-Secnd data sample at a value greater than the threshld value set in the Initialize Parameters table. The threshld values are in engineering units. The user can edit, delete r add new values in the table with the Add and Del buttns. 17. The user may print ut a hard cpy f the Initialize Parameters table t a printer cnnected t the Statin Manager data lgger by clicking n the Print buttn at the bttm f the table Averaging Methds The fllwing sectin describes the methds Statin Manager data lggers emply t average r calculate data channels. This methd applies t analg input channels and numerically calculated channels that use data frm ther analg input data channels r digital inputs channels. Statin Manager Data lggers cllect apprximately 10 samples per secnd frm every analg input channels and calculated channels. These samples are averaged int 1-secnd data samples fr each channel. A large quantity f samples, r ver-sampling, is used t achieve accurate recrding f all data channels and prvide smthing f 1-secnd data samples. 1-secnd data samples are held in memry fr calculatins, but are nt stred in nnvlatile memry n the hard disk f the Statin Manager Data lgger. 1-secnd data samples fr all channels are available fr display in the Statin Manager Data lgger Instantaneus Data Display screen. 1-secnd data samples fr each channel are averaged int 1-minute averages, shrtterm averages, and 1-hur averages. Shrt-term averages are user selectable and may be set t either 5-minute r 6-minute averages. Only the 1-minute, shrt-term, and 1-hur averages are stred n the Statin Manager Data lgger hard disk in nn-vlatile strage. 1-secnd average data samples are nt stred n Statin Manager s hard disk. 47

49 The fllwing are acrnyms and synnyms assciated with the averaging methds prvided in the meterlgical calculatins: WSR WSA WS i WDR WDA WD i sigma theta WSN WSN i sigma v VWS VWS i VWSA sigma w sigma phi N S V U Wind Speed Resultant Wind Speed Average Instantaneus Wind Speed Wind Directin Resultant Wind Directin Average Instantaneus Wind Directin Wind Directin Standard Deviatin Wind Speed Nrmal t Resultant Wind Vectr Instantaneus Wind Speed Nrmal t Resultant Wind Vectr Standard Deviatin f Wind Speed Nrmal t Resultant Wind Directin Vertical Wind Speed Instantaneus Vertical Wind Speed Average Vertical Wind Speed Vertical Wind Speed Standard Deviatin Standard Deviatin f the Vertical Wind Directin Number f Instantaneus Samples Analg Input Signal Nrth-Suth Cmpnent f the Wind Vectr East-West Cmpnent f the Wind Vectr 1. Arithmetic Averaging A. The standard averaging methd used fr mst data channels is the Arithmetic averaging methd. B. This methd is cmmnly used fr many air quality, meterlgical, and CEMS parameters; such as O3, SO2, CO, temperature and flw. C. During the initializatin f the Statin Manager data lgger, the user can specify the arithmetic averaging technique fr any desired analg signal (S) input channel. The prcedure fr perfrming this type f initializatin is described in Sectin D. Statin Manager data lgger uses the 1-secnd data samples frm each f the channels that are initialized fr arithmetic averaging t cmpute 1-minute averages. Every minute, sixty 1-secnd samples are averaged t make the 1-minute averages and the 1-minute averages are then used t cmpute arithmetic shrt-term averages and 1-hur averages. E. The fllwing is the equatin Statin Manager data lgger uses fr cmputing standard arithmetic averages fr any data channel (S): A = N i=1 N S i Where N is the number f 1-secnd samples 48

50 2. COH (1 Hr) - Cefficient f Haze 1 Hur Calculatin A. Cefficient f Haze (COH) is a measurement f particulates perfrmed by an AISI tape sampler r ther samplers, which use the same data sampling technique. B. COH is measured in the engineering unit f COH and represents a single measurement value taken at the end f each measurement perid. C. COH 1-hur measurement perids are (0000 t 0059)... ( ). COH values are stred in the regular hurly average data files n the hur f each measurement perid. D. COH is initialized with the prcedures fr using the Initialize Parameters table described in Sectin E. The fllwing is the algrithm Statin Manager uses t cmpute COH: 1). At the beginning f each measurement perid, Statin Manager enables digital utput line number 8 r 16 fr apprximately 5 secnds. 2). If a relay interface PC Bard has been installed n the Statin Manager data lgger, the relay cntacts n digital utput line number 8 r 16 will clse. If a relay interface PC Bard was nt installed, and if nly TTL digital utput lines are available, the event described in (1) abve will cause the TTL utput n digital utput line number 8 r 16 t transitin frm a lgical 0 state (high, apprximately 5 VDC) t a lgical 1 state (lw, apprximately 0 VDC). 3). Users shuld nrmally cnnect the relay utput line described abve t the tape advance signal terminals n an AISI tape sampler. The clsing f this relay will cause the AISI tape sampler t advance t the next measurement perid. Other custm interfaces can be emplyed t cause the TTL level signal t switch a relay device t accmplish the advance f the AISI tape sampler. 4). One minute after the beginning f a measurement perid, Statin Manager data lgger will stre a 1-minute average value frm the COH data channel. This 1- minute average will represent the beginning r tare value fr each COH measurement perid. 5). 58 minutes later, Statin Manager data lgger will recrd a secnd 1-minute average data value frm the COH channel. This value will be the final measurement value fr the COH channel fr each measurement perid. 6). At the end f every measurement perid, Statin Manager data lgger slves the fllwing equatin t yield a single measured value f COH: LOG (VB/VE) x 100 x 1000 / (Sample Time (min)) x Air Flw 3. COH (2 Hr) - Cefficient f Haze 2 Hur Calculatin A. Cefficient f Haze (COH) is a measurement f particulates perfrmed by an AISI tape sampler. B. COH is measured in engineering units f COH, and represents a single measurement value taken at the end f each 2-hur measurement perid. 49

51 C. COH 2-hur measurement perids are (0000 t 0159), ( ), ( )... ( ). COH values are stred in the regular hurly average data files in the dd hur f each 2-hur measurement perid. D. COH is initialized with the prcedures fr using the Initialize Parameters table described in Sectin E. The fllwing is the algrithm Statin Manager data lgger uses t cmpute COH. 1). At the beginning f each 2-hur measurement perid, Statin Manager data lgger will cause digital utput line number 8 r 16 t be enabled. Digital utput line number 8 r 16 will stay enabled fr apprximately 5 secnds. 2). If a relay interface PC Bard has been installed n the Statin Manager data lgger, the relay cntacts n digital utput line number 8 r 16 will clse. If a relay interface PC Bard was nt installed, and if nly TTL digital utput lines are available, the event described in (1) abve will cause the TTL utput n digital utput line number 8 r 16 t transitin frm a lgical 0 state (high, r apprximately 5 VDC) t a lgical 1 state (lw, r apprximately 0 VDC). 3). Nrmally, users will cnnect the relay utput line described abve t the tape advance signal terminals n an AISI tape sampler. The clsing f this relay will cause the AISI tape sampler t advance t the next 2-hur measurement perid. Other custm interfaces can be emplyed t cause the TTL level signal t switch a relay device t accmplish the advance f the AISI tape sampler. 4). One minute after the beginning f a 2-hur measurement perid, Statin Manager data lgger will stre a 1-minute average value frm the COH data channel. This 1-minute average will represent the beginning, r tare value, fr each 2-hur COH measurement perid. 5). 118 minutes later, Statin Manager data lgger will recrd a secnd 1-minute average data value frm the COH channel. This value will be the final measurement value fr the COH channel fr each 2-hur measurement perid. 6). At the end f every tw hur measurement perid, Statin Manager slves the fllwing equatin t yield a single measured value f COH: COH/1000 feet = min(6.25 lpm) Tare( r BeginningMinuteAverage) Lg FinalMinuteAverage 7). Since COH measurement perids are tw hurs lng, tw clck hurly average data psitins will be ccupied in Statin Manager s data lgger standard hurly average data file. 8). Statin Manager data lgger will recrd and stre a data value int each f these tw clck hurly data psitins during the 2-hur COH measurement perid. a) The difference value btained frm the abve equatin will be stred in the first f these tw hurly data psitins. b) The resultant COH data value, btained frm the slutin f the abve 50

52 4. Precipitatin - Rainfall Calculatin equatin, will be stred in the secnd clck hur data psitin in the COH data file n Statin Manager Data lgger. A. Statin Manager data lgger can recrd rainfall frm tw different types f rainfall sensrs. These include: 1). Tipping-bucket rain gauges 2). Cntinuus analg rain gauges B. Rainfall measured with a tipping bucket rain gauge r cntinuus analg rain gauge is usually scaled in inches per hur ( /hr) r millimeters per hur (mm/hr). C. The fllwing describes hw Statin Manager data lgger recrds rainfall with a tipping-bucket rain gauge. 1). Tipping bucket rain gauges emply mercury-wetted switch cntacts t signal the ccurrence f a tip f a small tipping-bucket when rain is cllected during a rain event. The switch cntacts in the tipping bucket rain gauge apply a vltage frm an external surce f vltage t an analg input channel in Statin Manager data lgger. 2). The maximum vlume f water that can be held in the tipping bucket determines the minimum data reslutin f the rainfall measurement frm a tipping bucket rainfall sensr. 3). In mst cmmercial tipping bucket rain gauges, the vlume f water cllected in the tipping bucket crrespnds t 0.01 inches, r 0.25 mm f rainfall. 4). Statin Manager data lgger stres the value f 0.01, r 0.25, in an editable disk file. Statin Manager data lgger in the calculatin f rainfall ttal uses this value. The default value stred in Statin Manager data lgger is The stred value can be set t 0.01, 0.25, r ther values n request. 5). Statin Manager data lgger cunts the number f tips f the bucket each clck hur perid, and multiplies the number f tips times the value stred in the disk file. The result f this calculatin is the hurly rainfall ttal. 6). The user sets the engineering units f rainfall recrded by Statin Manager data lgger when the apprpriate units are selected in Initialize Parameters table. Rainfall is typically recrded in in/hr r mm/hr. Statin Manager data lgger uses a standard analg input channel fr the recrding f a tipping bucket rain gauge. 5. Scalar HWD - Hrizntal Wind Directin A. Hrizntal wind directin is a circular functin with values limited t between 001 and 360 degrees. B. The hurly calculatin f wind directin average is a crssver-crrected average f the instantaneus wind directin samples. C. A crssver algrithm fr handling wind directin crssver thrugh nrth is used that cmpares the current instantaneus wind directin value t the average f all the preceding wind directin values fr the pertinent averaging perid. If a difference f mre than +180 degrees is fund, 360 degrees is subtracted frm the current value; r if a difference f less than -180 degrees is fund, then

53 degrees is added. D. The fllwing is the equatin Statin Manager data lgger uses fr calculating the average hrizntal wind directin (WDA): WDA = N i=1 WD N i 6. Scalar WS - Wind Speed Average Calculatin A. Hrizntal wind speed (WSA) is scalar hrizntal wind speed. B. Hrizntal wind speed (WSA) may be averaged int 1-minute, shrt-term, and 1- hur calculatins f average scalar hrizntal wind speed. C. The fllwing is the equatin Statin Manager data lgger uses fr calculating scalar hrizntal wind speed (WSA): WSA = N i=1 WSA N i 7. Sigma Standard Deviatin Calculatin 1. Sigma calculatins are the standard deviatin f selected analg input channels. 2. During initializatin, the user may specify the calculatin f sigma, r standard deviatin fr any analg input channel. 3. Sigma can be calculated and averaged int 1-minute, shrt-term, and 1-hur averages. 4. The fllwing is the frm f the standard equatin Statin Manager data lgger uses fr cmputing sigma fr any analg input data channel (S): Sigma = N i= 1 ( S i S) N Sigma Phi Calculatin A. Statin Manager data lgger calculates Sigma phi using the Sigma w and hrizntal wind speed (WSA) data channels. B. Sigma phi can be averaged int 1-minute, shrt-term, and 1-hur averages. C. The fllwing is the equatin used in the Statin Manager data lgger fr 52

54 calculating Sigma phi: Sigma phi = Sigma w WSA The abve equatin yields Sigma phi in units f radians and it is cnverted t degrees by Statin Manager Data lgger using the fllwing equatin: Sigma phi (degrees) = Sigma phi (radians) X Sigma Theta Calculatin A. Sigma theta calculatin is the standard deviatin f the hrizntal wind directin. B. Sigma theta is calculated frm the instantaneus wind directin samples. An algrithm similar t the crssver algrithm used fr hrizntal wind directin is used. C. Sigma theta can be calculated and averaged int 1-minute, shrt-term, and 1-hur averages. D. It has been suggested that the upper limit f Sigma theta shuld be limited t degrees (Yamartin, 1984). The equatins used in the Statin Manager data lgger d nt impse a limit t the range f pssible Sigma theta values recrded t eliminate any bias that an upper limit may impse. E. The fllwing is the equatin Statin Manager data lgger uses fr cmputing Sigma theta frm hrizntal wind directin (WD): Sigma Theta = N i= 1 ( WD i WDA) N Sigma v Calculatin A. Sigma v is the standard deviatin f the instantaneus wind speed nrmal t the hurly resultant wind directin. B. Sigma v can be averaged int 1-minute, shrt-term, and 1-hur averages. C. The fllwing is the equatin Statin Manager data lgger uses fr the calculatin f Sigma v: sigma v = N i= 1 u 2 i cs 2 WDR 2 N i= 1 U V i i ( sinwdr )( cswdr ) N 1 + N i= 1 V 2 i sin 2 WDR 53

55 where: ui = WSi sin WDi and Vi = WSi cs WDi 11. Sigma W Calculatin A. Sigma w is standard deviatin f the average vertical wind speed (VWSA). B. Sigma w can be averaged int 1-minute, shrt-term, and 1-hur averages. C. The fllwing is the equatin used in the Statin Manager data lgger fr calculating Sigma w: Sigma w = N i= 1 2 i 1 N ( VWS VWSA) Vectr WD - Resultant, r Vectr Wind Directin Calculatin A. The hurly calculatin f resultant r vectr wind directin prvides a vectr average f all f the instantaneus samples f wind directin sampled each hur. B. Vectr WD can be averaged int 1-minute, shrt-term, and 1-hur averages. C. The fllwing are the equatins Statin Manager data lgger uses fr the calculatin f vectr wind directin: U = V = N i=1 N i=1 [ WS sin( WD )] i N [ WS cs( WD )] i N i i WDR = U arctan + Flw V where: FLOW = U 0 arctan < V U 0 arctan > V 13. Vectr WS - Resultant, r Vectr Wind Speed Calculatin A. The hurly calculatins f resultant r vectr wind speed prvide a vectr average 54

56 f all f the instantaneus samples f wind speed sampled each hur. B. Vectr WS can be averaged int 1-minute, shrt-term, and 1-hur averages. C. The fllwing are the equatins Statin Manager data lgger uses fr the calculatin f vectr wind speed: U = V = N i=1 N i=1 [ WS sin( WD )] i N [ WS cs( WD )] i N i i WDR = U arctan + Flw V where: FLOW = U 0 arctan < V U 0 arctan > V 2 2 ( U V ) 0. 5 WSR = VWSA - Vertical Wind Speed Calculatin A. Vertical wind speed is the vertical cmpnent f wind flw. Vertical wind flw can be psitive (upward), r negative (dwnward). B. Vertical wind speed (VWSi) can be averaged int 1-minute, shrt-term, and 1-hur averages (VWSA). C. The fllwing is the equatin Statin Manager data lgger uses fr calculating average vertical wind speed average: VWSA = N i=1 VWS N i Initialize Plling The Initialize Plling screen is used t enter infrmatin needed fr the plling prgrams int the Statin Manager Data lgger set f initializatins. This screen can be accessed by selecting Initialize Statin frm the Initializatin Menu, then Initialize Plling. Figure

57 Figure 3-29 Initialize Plling Screen 1. This screen cntains the Primary Statin Name and an Alternate Statin Name. The user may enter a new name r change an existing name by highlighting the entry area with the muse. 2. The maximum number f characters fr the primary and alternate statin names is 8 characters. 3. Plling Passwrds are nt required fr EMC Statin Manager data lggers. 4. There is als a prvisin fr entering a secndary passwrd. Statin Manager data lggers d nt use the secndary passwrd. 5. This screen is fr entering the Primary ID Number fr this Statin Manager data lgger. It als includes an entry area fr entering a Secndary ID Number. 6. The Primary Plling ID Number is als used fr ESC plling emulatin. Whenever a Statin Manager data lgger is plled with the ESC plling prtcl, it is necessary t enter the apprpriate Statin ID int this entry area Initialize Statin Table The Initialize Statin screen is used t enter general infrmatin abut the site int a Statin Manager Data lgger. T view this screen, select Initialize Statin frm the Initialize Statin Menu. Figure

58 Figure 3-30 Initialize Statin 1. The Initialize Statin screen cntains several entry fields that can be initialized by the user. These include General Infrmatin, Lcal Time Znes, and Calibratin Reprt Type. A. Under General Infrmatin, there are three types f infrmatin that can be entered. 1). The first telephne number is the Plling Line 1 r the primary line that will be used fr plling f this mnitring statin. 2). The secnd telephne number is the Plling Line 2 r a secndary telephne line that culd be ptentially used at this mnitring statin. 3). The third telephne is Vice Line 1. This culd be a separate vice telephne line that is used at this mnitring statin. 4). The frmat f telephne numbers shuld be: (999) B. The secnd entry area is used t enter the full statin name, address and zip cde. The descriptin name entered here is used by Statin Manager data lgger as the header name in the Daily Summary Printuts. C. The third entry area is a Site ID Nr, and can be a unique site identificatin number r name fr the user s air mnitring netwrk. 3. Under the heading Lcal Time Zne is ne entry area that is used t set the Lcal Time Zne where the mnitring statin is lcated. Available time znes can be selected by pressing the select buttn n this entry area. 4. Under the heading Calibratin Reprt Type is the entry area fr selecting the type f Calibratin Reprt that will be printed ut at this Statin Manager data lgger lcatin. The selectin f the reprt style is dne by pressing the select buttn n this screen. 57

59 A. The first reprt frmat style is the EMC standard daily calibratin summary reprt fr ambient air quality mnitring. B. The secnd reprt frmat style is the EMC standard, daily calibratin summary reprt fr Cntinuus Emissin Mnitring Systems (CEMS) Initialize Cm Prts Statin Manager Data lggers can use multiple serial prt cnnectins. This screen is used t set the perating mde fr each f the Statin Manager Data lgger serial cmmunicatins prts. T view this screen, select the Initializatin Menu, select Initialize Statin, and then Initialize Cm Prts. Figure 3-31 Figure 3-31 Initialize Cm Prts 1. The Initialize Cm Prts screen displays fur Cm Prt selectins identified as Cm 1 thrugh Cm 4. Each cm prt has a separate pull-dwn list. The pull-dwn lists cntain varius selectins that are pssible fr serial cmmunicatins with the Statin Manager Data lgger. A. Nt Used. This selectin is entered when the cnnectin t the Cm Prt is nt required, r t disable the existing cnnectin. B. Plling Dial Up Line. This is the standard selectin that is used fr cmmunicatins with Statin Manager Data lgger. It includes EMC s System Manager plling, ESC Plling and SUMX plling. C. Plling Leased Line. This selectin is used fr dedicated r leased telephne line cmmunicatins with the Statin Manager Data lgger. D. Signal Interface Unit. This selectin is used t designate which line will cmmunicate with Statin Manager Data lgger Signal Interface Unit. E. Serial Calibratr Cntrl. This selectin is used t assign ne f Statin Manager s data lgger tw serial cmmunicatins prts t cmmunicate with and 58

60 cntrl an Envirnics 9100 r Series 100, r Dasibi 5008 calibratr. Serial Calibratr Cmmands are detailed in Sectin F. Serial Data Chevmn. This selectin is used fr special cmmunicatins with a prprietary cmputer data acquisitin system. 2. Select the Exit Buttn t save the Cm Prt initializatin. The user will be prmpted t cnfirm that the mdem has been cnnected t the apprpriate Cm Prt and that it is pwered n. 3. The Initialize Plling Screen buttn is available frm this screen t prvide direct access fr entering infrmatin needed fr the plling prgrams, as described in Sectin Calibratin Schedules This sectin describes the features f the Calibratin Schedules table shwn belw in Figure T view this table, select Calibratins frm the Main Menu and then select Calibratins Schedule. Figure 3-32 Calibratin Schedules Table 1. The Calibratin Schedules table is used t schedule the autmatic ccurrence f a calibratin sequence. The user can initiate calibratin sequences n an autmatic scheduled basis with the Calibratin Schedules table r manually at any time fr the Initiate Calibratins screen. A. Calibratin sequences are pre-defined and are stred in the Calibratin Sequences table. B. Users may select sequences prvided by EMC, r create custm calibratin sequence t satisfy their unique calibratin cntrl and scheduling requirements. Refer t Sectin fr a descriptin f the Calibratin Sequences table. 59

61 2. When initially setting up a schedule fr a calibratin activity, the user will enter the date when the initial ccurrence f the calibratin sequence will ccur. The Calibratin Schedules table autmatically keeps a running recrd f when the next ccurrence f each scheduled calibratin sequence will ccur. 3. It is pssible t schedule the frequency f ccurrence f a calibratin sequence by selecting a value in a pull-dwn list f pssible ccurrence frequencies the Calibratin Schedules table. Pssible selectins include: Daily, Weekly, Mnthly, Bi-Weekly, Semi-Mnthly, r Every N Days. 4. The Calibratin Schedules table cntains the time f day when each scheduled calibratin sequence will be perfrmed. The user can easily adjust this time t any desired starting time. 5. The fllwing example in Figure 3-33 illustrates hw the standard Edit Mde capabilities available in all Statin Manager data lgger tables can be used t edit r enter new values in this table. 6. As in all Statin Manager data lgger tables, selecting the Edit buttn at the bttm f the table causes the table t display the edit regin. 7. After a line has been edited, r after a new line has been created, pressing the Save Line buttn causes the edit regin t disappear and the full table t be displayed again. 8. When exiting tables, the changes made by the user will be saved nly when the Save Line buttn has been pressed. Figure 3-33 Calibratin Schedules Table - Edit Mde Calibratin Sequences 60

62 The fllwing table shwn in Figure 3-34 illustrates the Statin Manager Data lgger Calibratin Sequences table: Figure 3-34 Calibratin Sequences Table 1. The Calibratin Sequences table is used t initialize and stre any desired cmbinatin f calibratin steps that are created by the user. 2. Each calibratin sequence is given a unique user-defined name. 3. Once calibratin sequences have been created, they can be initiated autmatically using the Calibratin Schedules table described in Sectin Calibratin sequences can als be initiated manually at any time. 4. The Calibratin Sequences table cnsists f clumns, r fields f pertinent infrmatin needed t specify a sequence f calibratin steps. The fields r clumns in the table include: A. A list f user defined Calibratin Sequence Names. Users may add r delete the names in this list. B. The Step number that identifies the rder in which calibratin steps will be perfrmed. C. A single parameter r a grup f parameters whse calibratin respnses will be recrded and during a calibratin step. D. The single parameter r a grup f parameters that wuld be marked dwn as invalid during a calibratin step. E. A list f names that are available t describe each calibratin step. The pssible names include: Zer, Span, Precisin, Level 1, Level 2, Level 3, Level 4, Level 5, Level 6, and 61

63 Level 7. F. The time duratin, r Length f Step f each calibratin step. G. The time duratin, r Average Time when a sample is recrded during a calibratin step. H. The time duratin, r Recvery Time that can specified at the end f calibratin sequence step when calibratin respnses will nt be recrded and when data is nt included in the 1-minute, shrt-term, r hurly average data. 5. The number f pssible steps in each calibratin sequence is limited t 99 and the number f pssible calibratin sequences that can be created n a Statin Manager data lgger is Each step in a sequence can apply t ne r mre parameters. A sequence step can be cmbined t apply t multiple parameters, r nly ne parameter. 7. Each sequence can have a unique, user-defined name that will be recgnized by ther Statin Manager data lgger prgrams. 4.0 Statin Manager Features The fllwing sectin prvides a descriptin f the display screens and peratinal features f the Statin Manager Data lgger. It illustrates each screen display and summarizes the details abut the functin f each screen display r prgram. 4.1 Statin Manager User-Interface The Statin Manager Data lgger user-interface cnsists f a series f graphical menus, which prvide easy access t the unique screen displays in the data lgger. The Main Menu is the first screen in the hierarchy f menus and screens in the Statin Manager Data lgger. Each sub-menu and each majr functinal screen is represented by an icn buttn n the Statin Manager Main Menu screen. Whenever a Statin Manager Data lgger is initially started r rebted, it will display the fllwing Main Menu screen shwn in Figure

64 Figure 4-1 Main Menu Screen The Menu Statin hierarchy starts with a Main Menu screen and leads users t sub-menus that cntain a secnd level f screen selectins. Sub-menus can cntain a third Menu Level that will lead t further selectins and functins. Clicking nce n any f the push buttns icns shwn n the Main Menu will display the selected screen r functin. An Exit buttn is always lcated at the tp right crner n all screens in the Statin Manager Data lgger. The Exit buttn can be used at any time t exit r clse any screen display and mve t the next higher level in the Menu System. The Lg buttn n the Main Menu is used t lg a user ut f the Security System. Once lgged ut, users must lg-in again t access the Statin Manager Data lgger. 4.2 Statin Manager Map Screen The Map screen is an alternative methd f navigating amng the screen displays and functins in the Statin Manager Data lgger. This screen displays a hierarchical view f the majr prgrams and screen displays within the Statin Manager Data lgger. The Map screen selectin system is interchangeable with the selectin functins f the Statin Manager Menu system. Figure

65 Figure 4-2 Map Screen Open the Map screen within any screen in the Statin Manager Data lgger by clicking n the Map buttn lcated at the tp right crner f all screens. The Map screen is a quick and cnvenient way t lcate different menus and screens in the Statin Manager Data lgger. The Map buttn is lcated n every Statin Manager Data lgger screen at the tp right crner. Simply lcate the name f a menu r screen and single click t pen it. Users can return t the Map screen at any time by clicking n the Map buttn. 4.3 Calibratin Cntrl Prgram The Statin Manager Data lgger calibratin cntrl prgram is used t initiate calibratin activities. This prgram can als be used t cntrl the ccurrence f repetitively scheduled events. The Statin Manager calibratin cntrl prgram includes a main Calibratin Menu fr managing calibratin activities fr ambient air quality and CEMS mnitring statins. The calibratin system is administered thrugh the varius tables and dialg bxes available under the Calibratin Menu. Calibratin cntrl activities typically cnsist f manually initiated calibratins, manually initiated calibratin sequences, and calibratins that are scheduled t run autmatically n a scheduled, repetitive basis accrding t user-defined schedules. T display the Calibratin Menu shwn in Figure 4-3, click the Calibratins buttn n the Main Menu. 64

66 Figure 4-3 Calibratin Menu The Calibratin Menu cntains the fllwing selectins that are used fr cntrl f calibratin activities: Initiate Calibratins Calibratin Schedules Calibratin Sequences Calibratin System Timer-Cntrl Table Manual Reprts Calibratin Cntrl Chart Digital Input-Output Table Mark Dwn Channels Initiate Calibratins The Initiate Calibratins screen is primary screen in the Statin Manager Data lgger fr accessing the dialg bxes and prgrams needed t perfrm calibratin activities. It prvides direct access t a Manual Calibratin dialg bx and the Start Calibratin Sequence dialg bx. It als includes access t ther prgrams in the Statin Manager Data lgger, such as the Instantaneus Data Display prgram and the Strip Chart display prgram. T display the Initiate Calibratins screen shwn in Figure 4-4, click the Initiate Calibratins buttn n the Calibratin Menu screen. 65

67 Figure 4-4 Initiate Calibratins Screen 1. The Initiate Calibratins screen is the primary screen fr selecting dialg bxes that are used fr and cntrlling Manual Calibratins and Manually initiated sequences. 2. This screen als prvides easy access t the Instantaneus Data Display screen. Clicking n the Instantaneus Data selectin buttn will quickly bring up a display f all data recrded n the Statin Manager Data lgger. 3. Clicking n the Print Summary buttn will prvide access t the Calibratin Data display and printing prgram. 4. The Strip Chart buttn will prvide access t the Strip Chart display prgram. 5. The fllwing sectins describe each f the dialg bxes and display screens that can be accessed thrugh the Initiate Calibratins screen Calibratin Sequence When the Calibratin Sequence buttn is pressed, the Calibratin Sequence dialg bx shwn in Figure 4-5 will appear and be displayed n tp f the Initiate Calibratins Screen. 66

68 Figure 4-5 Calibratin Sequence Dialg Bx a) The Calibratin Sequence dialg bx is used t start pre-defined calibratin sequences. b) The Select Sequence buttn n this dialg bx has a pull-dwn list f available calibratin sequences, which have been previusly defined and stred in the Calibratin Sequence table. c) T start a calibratin sequence, select a calibratin sequence, the press the start buttn. The Start buttn will turn red, indicating that it has started the selected calibratin sequence. d) The calibratin sequence will run thrugh the sequence f steps defined in the Calibratin Sequence table. If needed, the user can manually terminate this sequence at any time by clicking n the Stp buttn and answering yes t a cnfirming dialg bx. e) Befre a calibratin sequence can be initiated, either manually r autmatically, the sequence must have previusly been defined and stred in the data lgger s Calibratin Sequence table. Review Sectin fr a descriptin f this prcedure Manual Calibratin When the Manual Calibratin buttn is pressed, the Manual Calibratin dialg bx shwn in Figure 4-6 will appear and be displayed n tp f the Initiate Calibratins Screen. Figure 4-6 Manual Calibratins Dialg Bx a) The Manual Calibratin dialg bx is used start a manual calibratin activity. b) A manual calibratin activity is ne in which the user selects the parameter, the type f calibratin activity t be perfrmed, and then manually starts the calibratin activity by pressing the Start buttn. c) Click the Calibratin Activity buttn n the dialg bx t pen a pull-dwn list f chices f different calibratin activity names. Pssible calibratin activity names are: Zer, Span, Precisin, and Level 1 thrugh Level 7. Select the desired calibratin activity by clicking n the name in this pull-dwn list. d) Click the Parameter(s) buttn n the dialg bx t pen a list f parameters that have been initialized in the Statin Manager Data lgger. Select the desired gaseus 67

69 parameter t be calibrated. Multiple parameters can be calibrated at ne time by clicking n the Multi-Select buttn. After multiple parameters have been selected, click the End Selectin buttn at the bttm f the list. e) Press the Start Calibratin buttn t start the calibratin activity. It will depress and turn red, indicating the selected calibratin activity has started. f) When a calibratin is started, apprpriately defined digital utputs in the Digital Input/Output Tables will turn n a pattern f relays that cntrl external calibratrs r valves. If an RS-232C serial interface has been enabled, Start cmmands will cncurrently be sent t an RS-232C serial prt. g) Once started, a manual calibratin activity will stay enabled until the user presses the Stp buttn n the dialg bx. h) Once the analyzer being calibrated has attained a stable respnse during the manual calibratin activity, click the Start Averaging buttn t begin averaging data. The averaging f calibratin data respnses will cntinue until the Stp buttn is pressed. The calibratin data respnse recrded during this time interval will be stred in the Statin Manager Data lgger calibratin data files n the Statin Manager Data lgger hard disk. Calibratin respnses can be printed ut r viewed n-screen by using the Calibratin Data display and printing prgram. i) While a manual calibratin is running, it is pssible t exit r clse the dialg bx and still cntinue the calibratin activity. This will permit the user t exit this screen and perfrm ther tasks within the Statin Manager data lgger while a manually initiated calibratin is still in prgress j) The fllwing is a recap f the steps that are used t perfrm a manual calibratin: k) Select the type f calibratin activity as explained abve. l) Select the parameters t be calibrated as explained abve. m) Click the Start Calibratin buttn. n) Click the Start Averaging buttn when the analyzer has attained a stable respnse and the user wishes t begin averaging the calibratin respnse. ) Click the Stp buttn at any time t terminate the calibratin activity and the averaging f the calibratin data respnse. p) Click the Exit buttn t clse the Manual Calibratins dialg bx. q) While a manual calibratin is running r still in prgress, it is pssible t exit r clse the dialg bx. This will permit the user t exit this screen t perfrm ther tasks within the Statin Manager Data lgger while the manual calibratin is still running. r) Stp, r terminate a Manual Calibratin activity by pressing the Stp buttn Instantaneus Data Display The Instantaneus Data Display screen prvides a tabular view f all data channels recrded by the Statin Manager Data lgger. Click the Instantaneus Data buttn n the Calibratins Menu t view the Instantaneus Data Display screen shwn in Figure

70 Figure 4-7 Instantaneus Data Display Screen a. This Instantaneus Data Display screen can be accessed frm either the Data Menu r the Initiate Calibratins screen. b. The Instantaneus Data Display screen shws the channel number, the parameter name, input vltage reading fr each analg input channel, and instantaneus reading in engineering units. It als shws the latest 1-minute, ther averages (5-minute r 6- minute), previus 1-hur average (updated hurly), and the sliding 1-hur average (updated every five minutes) in engineering units Print Calibratin Summary Dialg Bx a. Click the Print Summary buttn t initiate a printut f a calibratin summary. b. Select the date with the up and dwn arrw buttns. c. Click the view r print buttn t btain a display r printut f calibratin data View Strip Charts Dialg Bx a. The View Strip Charts dialg bx is used t pen and view a strip chart. b. Click the Select Chart Name buttn and click n the chart name t be displayed. c. Click the Vertical r the Hrizntal Display buttns t autmatically pen the selected Strip Chart Calibratin Schedules Table 69

71 The Calibratin Schedules table is used t schedule when pre-defined calibratin sequences will be run. Open the Calibratin Schedules table shwn in Figure 4-8 by clicking n the Calibratin Schedules buttn n the Calibratins Menu. Figure 4-8 Calibratin Schedules Table 1. T cause a pre-defined calibratin sequence t run at a scheduled time, the user shuld make apprpriate entries in the Calibratin Schedules table. 2. The table cntains fur entry fields r clumns. 3. The first clumn in the table is the pre-defined Calibratin Sequence Name. Select a sequence name frm the pull-dwn list f pre-defined sequences. Refer t Sectin fr the prcedures fr creating pre-defined calibratin sequences. 4. The Frequency f Occurrence clumn specifies when a sequence will run. The chices are every day, every N number f days, weekly, bi-weekly, r mnthly. Select the desired frequency f ccurrence frm the pull-dwn list f pssible chices. 5. The Next Cal Date specifies the next date n which the selected calibratin sequence will run. Select the next starting date fr the calibratin sequence. 6. The Start Time specifies the starting time n the next calibratin date. Select the starting time. 7. When the user has entered these selectins and pressed the Save buttn in the Edit Regin, the specified calibratin sequence will repeat accrding t the user entries in the table. 8. Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. 70

72 9. Click the Print Schedule buttn t printut a cpy f the Calibratin Schedules table Calibratin Sequences Table Click the Calibratin Sequences buttn n the Calibratin Menu screen t pen the Calibratin Sequences table shwn in Figure 4-9. The Calibratin Sequence table is used t create and stre calibratin sequences. The user r System Administratr can create many different types f calibratin sequences. Sequences can have frm 1 t 99 steps and there can be as many as 1 t 99 calibratin sequences stred in this table. Figure 4-9 Calibratin Sequences Table 1. The Calibratin Sequences table includes clumns fr: Sequence Name - calibratin sequence name. Step - specifies rder psitin in calibratin sequence. Ave (Average) - whether r nt the parameter will have data averaged during the specified step in the calibratin sequence. Invalid - Parameters whse data is invalidated during a step. Level - the type f calibratin activity that will be perfrmed during a specified step number. Cal Flag - calibratin flag that will be listed during a step. Length f Step - time necessary fr the calibratin. Average Interval - amunt f time fr data t be averaged. Recvery Interval - amunt f time necessary fr a parameter t stabilize after a calibratin Calibratin System The Surce Value table is used t manually enter r edit calibratin surce (theretical r true) values fr each type f gaseus parameters that the calibratin system requires. Click 71

73 n the Calibratin System buttn in the Calibratin Menu screen t pen the Calibratin System Menu as shwn in Figure Manually Enter Surce Values Figure 4-10 Calibratin System Menu Click n the Manually Enter Surce Values buttn frm the Calibratin System Menu t pen the Surce Value table as shwn in Figure The Surce Value table is used t manually enter r edit surce values fr specific parameters. The Surce Value Table displays the Parameter name, Type f Calibratin, Surce Value, Date, Operatr Name, and Cmments 72

74 Figure 4-11 Surce Value Table Edit Table Fr help with the Edit Mde Regin, please refer t Appendix Edit Mde Help. Print Table T print a hard cpy f the Surce Value table, click n the Print Table buttn. Surce Value Histry The Surce Value Histry able is nt yet peratinal Calibratr Cmmands The Calibratr Cmmand table is used t send cmmands t a dynamic dilutin calibratr thrugh an RS-232C serial data interface. This table permits the user t enter the apprpriate cmmands fr different manufacturer s calibratrs int this table and when the Statin Manager Data lgger perfrms a manual r autmatic calibratin activity, the calibratin prgram will send the crrespnding cmmands thrugh an RS-232C serial line t the calibratr. This feature will permit direct cntrl f different dynamic dilutin calibratrs with the Statin Manager Data lgger calibratin system. 73

75 Figure 4-12 Calibratr Cmmands Table Fr each specified type f calibratin activity, an enable string f characters r text will be sent t the calibratr thrugh the RS-232C serial line t cause a specified type f calibratin activity t ccur. An enable string is created by the user and stred in the Statin Manager Data lgger Calibratr Cmmand table t be sent thrugh the RS-232C serial line t the calibratr at the n-set f any specified calibratin activity. Each type f the Statin Manager Data lgger calibratin activity is specified by a parameter name and a type f calibratin activity. Calibratrs typically require that a stp string f characters r text be sent t it thrugh an RS- 232C serial data line at the end f each specified calibratin activity. The Statin Manager Data lgger will send the stp string f characters r text stred in the Calibratr Cmmand table at the end f each specified calibratin activity. The user can edit the Calibratr Cmmand table as needed t enter apprpriate cmmands fr the type f calibratr used. The types f calibratrs supprted include TEI 146C, Envirnics Series 100 and 9000, API, and Dasibi 5008 dynamic dilutin calibratr that have an RS-232C serial data interface installed. Other manufacturer s calibratrs that als require an enable string and a stp string t prperly perate will als perate with the Statin Manager Data lgger calibratr cntrl prgram. Click the Calibratr Cmmands buttn in the Calibratin System menu t pen the Calibratr Cmmands table shwn in Figure The Calibratr Cmmands table cntains fur entry fields: Type f Calibratin, Parameters (all parameters invlved in the calibratin), Enable String (cde string that triggers a calibratin), and Stp String (cde string that halts a calibratin). Edit Table Fr help with the Edit Mde Regin, please refer t Appendix Edit Mde Help. 74

76 Print Table T print a hard cpy f the Calibratr Cmmands table, click n the Print Table buttn Timer Cntrller The fllwing sectin cntains a descriptin f the Statin Manager Data lgger Timer- Cntrller prgram. The Timer-Cntrller prgram is used t schedule and cntrl systems and equipment that is typically used in Cntinuus Emissins Mnitring Systems (CEMS). The user may select equipment, such as slenid valves and samplers, t be cycled fr rutine mnitring activities and the data channels t be marked dwn fr the interval perid. The Timer-Cntrller prgram can detect a digital input and initiate a cntrl actin. The Timer-Cntrller table is shwn in Figure Timer Cntrller Table Figure 4-13 Timer Cntrller Table Each line in the Timer-Cntrller table specifies the executin f a separate cntrl actin. The actin may be repeated indefinitely, r it can be limited t ccur nly upn the detectin f a digital input signal. When the digital input field is selected in the table, the Statin Manager Data lgger will check the input and perfrm the selected actin as lng as the specified digital input line is enabled. The fllwing is a descriptin f the furteen fields in the Timer-Cntrller table. a) Descriptin This is a user-defined name fr the Timer-Cntrller actin. 75

77 b) Next Occurrence Grup This field specifies the initial time and date fr the cntrl actin n this line in the table. When the Time field is selected, the user is presented with the current time and date and tggle arrws t enter the apprpriate selectin. Since this type f cntrl actin is repetitive, the time entered will be the starting time and the Timer-Cntrller prgram will cntinue t repeat the cntrl actin indefinitely accrding t the repeat schedule. When the user enters the table, Statin Manager will calculate the next ccurrence fr display in the table. T cancel an actin, the user deletes the line frm the table. Sequential events may be prgrammed by selecting the same Time and Date fr all events, and prgramming the Wait Timer t prvide the necessary ffset fr the actins. The Wait Time is calculated in secnds, cunting frm the Time entered in the Next Occurrence grup r the Repeat timer. The user may elect t nt enter a Wait Time, r may reset the Wait Time t n wait by entering a zer. The editr will shw a blank fr entries that are zer. The Wait Timer cntrls the Digital Output actin, Delay Averaging and Invalid Parameters fields. The Repeat field is based n the Next Occurrence grup and nt affected by the Wait Timer. c) Dig In (Digital Input) enables a digital input t trigger a cntrl actin. By selecting a Digital Input channel (channel numbers 1 thrugh 32), the user can cntrl events related t anther system r utside activity. When selected, the Statin Manager Data lgger will test fr the digital input every secnd, and nce the digital input has been detected, the cntrl actins will persist as lng as the digital input line is enabled. T cancel the cntrl actin, the user deletes the line frm the table. Editing the Digital Input mde is similar t the Time Cntrlled events with the exceptin f the Next Occurrence time and date, and the Repeat Day and Minutes. The user can select either a Timed Event r a Digital Input mde f peratin. When a Time Cntrlled event and a Digital Input even share a digital utput, pririty is given t the Digital Input cntrl actin. d) Wait Sec defines any waiting perid required befre the actin is initiated. e) Turn (On/Off) Digital Output Grup specifies the digital utput line, the cntrl actin and duratin f the event. The Digital Output grup is cmpsed f three fields: Digital Output Number (Nr), On-Off and the Timer (Min-Sec). The Number field is used t select the specific digital utput t be active, numbers 1 thrugh 32. The On-Off field is used t select whether the digital utput line is placed in the On r Off state during the cntrl actin regardless f the prir state f the Digital Output. This timer determines the length f the cntrl actin starting frm the Next Occurrence grup r the Wait timer. When the Minute field is selected, the user may enter up t 9999 in the Minutes field and up t 99 secnds in the Secnds field. Entering a zer will display as a blank in either field. f) Delay Ave (Averaging) defines the parameters fr which sampling will be delayed fr the time interval entered. The Delay Averaging grup is used t select parameters t delay as a result f the cntrl actin, such as parameters that are briefly impacted by the switching f the digital utput. Multiple parameters may be selected and marked dwn, r invalid fr the perid specified in the Sec (Secnds) field. This timer begins at the Next Occurrence time unless a Wait perid has been selected. g) Invalid used t define ne r mre parameters fr which sampling will be marked dwn as invalid fr the duratin f the cntrl actin. The Invalid field is used t mark dwn, r invalidate, parameters fr the duratin f the cntrl actin. Multiple parameters may be selected and will be marked dwn fr the entire perid defined in 76

78 the Digital Output grup, starting at the Next Occurrence time unless a Wait perid has been selected. h) Repeat Grup specifies the interval that the cntrl actin will be repeated. Edit Table Fr help with the Edit Mde regin, please refer t Appendix Edit Mde Help. Print Table T print a cpy f the Timer-Cntrller table, click n the Print Table Buttn Timer Cntrller and Calibratr Prperties The Timer-Cntrller may manage functins shared by the Calibratin Prgram, such as parameters flagged as invalid and cntrl f digital utput lines. Pririty is given t the Calibratin Prgram when activities take place cncurrently. The fllwing table describes the activity in the Statin Manager Data lgger fr simultaneus actins: Activity Calibratin Timer-Cntrller Parameter Flagged Invalid Cncurrently by Bth Primary Cntrl Cntrller ignred until calibratin flag released Digital Output Line Enable Cncurrently by Bth Cntrller actin ignred and n change f state Digital Input Line Enable Cncurrently t Bth Parameter Flagged Invalid by Timer-Cntrller First Digital Output Line Enabled by Timer-Cntrller First Digital Input Line Enabled t Timer-Cntrller First. Parameter Flagged Invalid by Calibratr First Digital Output Enabled by Calibratr First Digital Input Line Enabled t Calibratr First Primary Cntrl Primary Cntrl Assumes Cntrl Assumes Cntrl Assumes Cntrl Retains Cntrl Retains Cntrl Retains Cntrl Cntrller actin ignred and n change f state Cntrller ignred until calibratin flag released Override Cntrller actin until released by calibratr Override Cntrller actin until released by calibratr Cntrller Actin ignred until calibratin cmplete Cntrller Actin ignred until calibratin cmplete Cntrller Actin ignred until calibratin cmplete Timer Cntrller Applicatins The Timer-Cntrller in the Statin Manager Data lgger ffers a general purpse prgram fr use with any functin that can be cntrlled by a digital utput and based n a timed event r input frm anther digital surce. The expected uses in the Statin Manager Data lgger are fr CEMS functins and several examples f this type f applicatin are ffered fr the user. While these examples are available t the user, several ther methds may exist t accmplish the same applicatin Stream Switching Example 77

79 An example f a Timer-Cntrller applicatin is a system, which switches frm ne sampling stream t anther sampling stream. This type f CEMS peratin is referred t as Stream Switching. This may ccur when the Statin Manager Data lgger is perating cntinuusly but selecting the surces, such as discharges frm multiple vents r exhaust pipes, n a rutine cycle. Figure 4-14 is an example cnfiguratin fr Stream Switching: 78

80 Figure 4-14 Example Table Defined fr Stream Switching The example parameters fr Stream Switching shwn here are defined with a minimum number f 15 valid 1-minute data samples per hur in the Initialize Parameters table as shwn in Figure 4-15: Figure 4-15 Example Table Defined fr Stream Switching 79

81 Stream Switching begins with the digital activatin f an autmated slenid valve allwing the mnitring equipment t receive the first surce, Stream A in this example. A built-in delay f 5 secnds allws fr the clearing f the residual vlume frm the surce piping. The data channels fr the alternate surces, Stream B and C, are marked dwn r invalid fr the sampling interval. After 5 minutes, the digital utput will return t the ff cnditin, clsing the autmated slenid valve fr Stream A. The wait timer fr Stream B, set t 300 secnds (5 minutes), will enable a secnd digital utput t pen a slenid valve fr Stream B sampling. Again the delay f 5 secnds allws fr the residual vlume in the surce piping t be exhausted prir t the cllectin f data. The assciated data channels fr Stream A and C are marked invalid. After 5 minutes, the digital utput will return t the ff cnditin and the slenid valve fr Stream B will clse. The wait timer fr Stream C, set t 600 secnds (10 minutes), will enable the third digital utput t pen the slenid valve fr Stream C sampling. The delay f 5 secnds clears the surce piping and data cllectin begins. The data channels fr Stream A and B are marked invalid and sampling fr Stream C will begin. After the cmpletin f the sampling perid, the digital utput will clse the slenid valve fr Stream C. The Repeat clumn, set t 15 minutes fr all streams, will cycle back t the Stream A sampling and cntinue the rtatin f the Stream Switching sequence Backflush Example The rutine functin f flushing the surce line is anther example f a timed event using the Timer-Cntrller prgram. Cmmnly referred t as Backflush, the applicatin invlves the reverse flw f cmpressed air thrugh the surce piping remving the misture r particulate material that may have been drawn int the line. Figure 4-16 is an example f scheduled Backflush activities: Digital Input Example Figure 4-16 Example Table Defined fr Backflush 80

82 When selected, the Timer-Cntrller tests fr a digital input every secnd and n receipt f an input initiates the actin determined in the table. An example f the use f this feature is the discharge f accumulated misture in surce piping. Figure 4-17 demnstrates a pssible use f this feature. Figure 4-17 Example Table Defined fr Digital Input The example sequence begins with the digital input frm a misture detectin sensr in the surce piping. The Timer-Cntrller flags the assciated data invalid and, thrugh a digital utput, activates an autmated slenid valve allwing the reverse flw f cmpressed air thrugh the surce piping r the draining f an accumulatr. When the sensr ceases t detect misture, the digital input is released and the valve clsed. The Timer-Cntrller will release the validity flags and data cllectin will resume as nrmal PM10 Sampler Example The sampling f particulate material in the atmsphere is ften accmplished by use f a PM- 10 Sampler, using a filter media and weight measurement. The sampler is run fr a perid f time usually 24 hurs. Figure 4-18 demnstrates a typical entry fr PM-10 sampler. 81

83 Figure 4-18 Example Table Defined fr PM-10 Sampler Manual Reprts The Manual Reprts screen, Figure 4-19, permits the user t display, print, r exprt any reprt defined in the Reprt Setup Table, refer t Sectin Figure 4-19 Manual Reprts Screen 82

84 Click the Manual Reprts buttn n the Calibratin Menu t pen the Calibratin Data screen. Click the Individual Reprts buttn and then select the pre-defined reprt desired. Refer t Sectin Click the up and dwn arrw buttns t select the day, mnth, and year f the reprt t be printed. T print preview the reprt, click n the Display buttn. This will display the reprt, as it will appear after it has been printed. Clicking n the Print buttn allws the reprt t be printed frm the View screen. Click n Exit t return t the Print Calibratin Reprt screen. T print the reprt withut previewing it, click the Print buttn versus the Display buttn. T exprt the reprt, click n the Exprt buttn and select desired frmat, typically PDF Calibratin Cntrl Chart Select Calibratin Cntrl Chart frm the Calibratin Menu t pen the Calibratin Cntrl Chart screen shwn in Figure 4-20 belw. This screen is used as a quality assurance tl fr viewing calibratin respnses. Figure 4-20 Calibratin Cntrl Chart The Calibratin Cntrl Chart vertically displays ne mnth s wrth f calibratin cntrl data. The tw red lines indicate the Upper Cntrl Limit (UCL) and the Lwer Cntrl Limit (LCL). These lines serve t warn the user if the calibratin data falls utside f the recmmended span percentage area, (generally +/- 10%). Refer t Sectin t set the Calibratin Cntrl Chart Limits fr each parameter. T view the Calibratin Cntrl Chart: Calibratin- select either Daily Autmatic Calibratin (Daily Autcals) r Precisin Ttals 83

85 Parameter- select ne parameter t view Mnth-year- select the time perid yu wish t view Retrieve- t view the chart Print- t print the results Digital Input-Output Table The Digital Input-Output Menu (Figure 4-21) is used t select which digital input r utput lines will be enabled during a calibratin activity Figure 4-21 Digital Input-Output Menu Digital Output Lines Table This table will display 16 r 32 digital utput lines when the Statin Manager Data lgger has been cnfigured with 16 r 32 digital utput lines. Figure 4-22 This table displays all f the pssible digital utput line cmbinatins fr each type f calibratin activity and parameter selected. The table cntains a clumn fr displaying all parameter names, a clumn fr displaying the calibratin activity fr the parameter, and 1-32 clumns displaying either the 1 r 0 designatin. A 1 represents an actuated, r n cnditin; a 0 represents an un-actuated, r ff cnditin. Each digital utput line can be used t cntrl external calibratin equipment, zer air systems, r ther equipment. When used with EMC s ptinal Relay Interface Bard, either 16 r 32 relay cntact clsures can be cntrlled with the Digital Output Lines table in the Statin Manager Data lgger Calibratin Cntrl Prgram. 84

86 Figure 4-22 Digital Output Lines Table Edit Table Fr help with edit peratins please refer t Appendix Edit Mde Help. Print Table Click n the Print Table buttn t print ut the Digital Output Lines table Digital Input Lines Table Digital input lines can be used t sense the ccurrence f externally cntrlled calibratin events. The Digital Input Lines table is used t specify which digital input lines will sense specific calibratin events. The table will display 16 r 32 digital input lines when the Statin Manager Data lgger has been cnfigured with 16 r 32 digital input lines. Figure

87 Figure 4-23 Digital Input Lines Screen This table displays all f the pssible digital input line cmbinatins fr each type f calibratin activity and parameter selected. The table cntains a clumn fr displaying all parameter names, a clumn fr displaying the calibratin activity fr the parameter, and 1-32 clumns displaying either the 1, 0 r X designatins. During initializatin and setup, the user will enter values int the Digital Input Lines table t cnfigure and setup the Statin Manager Data lgger t sense external calibratin events. In the Digital Input Lines table the user will assciate a 1, 0, r X value fr each cmbinatin f Parameter and Calibratin Activity needed using the pull-dwn lists in this table. After the Digital Input Lines table has been initialized, if a digital input line senses a lgical 1 input (r actuated state), the Statin Manager data lgger will interpret this cnditin as the ccurrence f the calibratin event specified in the Digital Input Lines table. When this ccurs, the Statin Manager data lgger will flag data fr that specified parameter and perfrm averaging f data fr during the last 5 minutes f the perid when the digital input line is set t the lgical 1 cnditin. The Statin Manager Data lgger will stre the averaged calibratin data respnse int its calibratin files fr that parameter. When a digital input line senses a lgical 0 input (r un-actuated state), the Statin Manager data lgger will interpret this cnditin as meaning n calibratin activity is taking place during the time perid when the digital input line sense a lgical 0. The Statin Manager Data lgger will nt perfrm flagging f data, r stre calibratin data respnses. If the user enters an X int the Digital Input Lines Table, the Statin Manager Data lgger will nt pay attentin t either the lgical 1 r 0 states fr the parameter and calibratin activity specified in the table. N flagging f data and strage f data will ccur when an X is entered int the Digital Input Lines table. This table displays all f the pssible digital input line cmbinatins fr each type f calibratin activity and parameter selected. 86

88 Digital Status Screen The Digital Status screen displays the current cnditin f any active Digital Input and Output lines, and is updated instantaneusly with the changes t any digital state. Figure 4-24 Figure 4-24 Digital Status Screen Mark Dwn Channels Screen The Mark Dwn Channels screen is used t manually mark ne r mre data channels ffline fr a selected perid f time. Click the Mark Dwn Channels buttn in the Calibratin Menu t pen the Mark Dwn Channels screen as shwn in Figure The Mark Dwn Channels screen shws tw sets f five clumns. The clumns are Parameter, Input Channel, On Line, Temprary Off Line, and Lng Term Off Line. The Parameter clumn shws all parameters cnnected t the Statin Manager Data lgger. These clumns shw all parameters cnnected t the Statin Manager Data lgger, the parameter channel numbers, and whether the channels are n line r ff line. The Mark Dwn Channels screen als has tw ther buttns: Mark All Channels On Line, and Set Temprary Time. 87

89 Figure 4-25 Mark Dwn Channels Screen T set any ne f the parameters t On Line, Temprary Off Line, r Lng Term Off Line clumns simply click in the clumn t the right f the parameter t be changed. After selecting a clumn a checkmark will appear signifying that that parameter is nw n r ff. Mark All Channels On Line T turn n all channels click n the Mark All Channels On Line buttn. Set Temprary Time T chse the length f the temprary ff line time, click n the Set Temprary Off-Line buttn. This will pen a list f different intervals f time t select frm. Select the desired interval. Then check the Temprary Off Line clumn title bx. The new interval f time will be listed there. Clicking n Exit lcated at the tp right crner f the screen at any time will clse the Mark Dwn Channels screen and return the Statin Manager data lgger t the Calibratin Activities Menu. 4.4 Strip Charts Selecting the Strip Charts buttn frm the Statin Manager data lgger Main Menu will pen the Select Chart screen. The Select Chart screen shwn in Figure 4-26 is used fr selecting the name f a pre-defined strip chart and the apprpriate time r date f the strip chart the user wishes t display. The Strip Chart Prgram is a highly realistic strip chart display r trending prgram. The strip chart prgram is used t visually validate and bserve data recrded by the Statin Manager data lgger. 88

90 Figure 4-26 Select Chart Screen Chart Selectin The Select Chart screen is cmpsed f several pull-dwn lists and selectin buttns. These include: a Pre-Defined Charts menu, Date Select, Make Chart menu, and a Display buttn User Defined Strip Chart The user is able t define their wn parameters desired n the strip chart Make Chart Selectin Bx The Make Chart menu is lcated at the tp left side f the Select Chart screen. This menu is used t select the parameter/s t be displayed n the strip chart. Clicking n the Parameter buttn will pen the parameter list. Frm there the chices are either pening a chart with nly ne parameter r pening a chart with multiple parameters. Chsing Single Parameters Click n a parameter frm the list will select that parameter t be displayed n the strip chart. Chsing Multiple Parameters T select multiple parameters: Click n the Multi buttn lcated at the bttm f the parameter list. Click n all f the parameters t be displayed n the strip chart Date Select Menu 89

91 The Date Select menu, centered at the tp f the Chart Select screen is used fr selecting the date f the chart the user wants t view. The menu cntains chices f real-time data, yesterday's data r histrical data. Real-Time Data Clicking n the Real-Time data buttn sets the strip chart prgram t display data n the strip chart as it is being recrded alng with the rest f tday s data. Yesterday Data Clicking n the Yesterday buttn autmatically sets the strip chart t display the previus day s data fr the selected parameters. Histrical Data T select a date fr viewing click n the Histrical buttn. Clicking n the up and dwn arrws directly belw the displayed date changes the day, mnth, and year Display Chart Buttn The Display buttn pens the strip chart n the screen. T change the view between the hrizntal and vertical views click n the arrw belw the Display buttn. T pen the chart, click n display. The Pre-Defined Charts menu is used t frmat frequently used strip charts. Up t 10 predefined charts may be created and stred in the Strip Chart Prgram. T use a Pre-Defined Chart: Click n the buttn pre-defined chart t be viewed. Select the chart date. Click n the display buttn Pre-Defined Strip Chart If the same set f parameters are desired each time the strip chart is brught up, the user is able t set up a list f pre-defined charts with single r multiple parameters Initialize Pre-Defined Charts T create a Pre-Defined Chart, press the Initialize buttn at the bttm f the Pre-Defined Charts menu. This pens the Initialize Chart screen shwn in Figure Clicking n the Exit buttn in the tp right hand crner f the screen at any time will clse the Initialize Pre- Defined Charts screen. Creating A Pre-Defined Chart Click n a blank Chart Name buttns n the left-hand side f the screen. (See Figure 4-27) Type the new chart name in the message bx. Press Enter r click n OK. The chart name buttn shuld nw have the new chart name printed n it. Click n the parameter bx directly t the right f the chart name buttn. Click n a parameter frm the parameter menu. Click n a clr frm the clr palette. This clr will represent the parameter when the strip chart is displayed. 90

92 The parameter bx shuld nw shw the clr and parameter name. T add anther parameter t this chart, click n the next parameter bx and repeat these steps. Deleting a Parameter r Chart T delete a parameter r chart, click n the delete buttn lcated n the bttm left side f the screen. Next, click n the chart r parameter t be deleted. Parameter Menu Clr Select Menu Delete Buttn Figure 4-27 Initialize Pre-Defined Charts Screen 91

93 4.4.2 Strip Chart Screen The Strip Chart prgram can display strip charts in either a vertically and hrizntally rientatin as shwn in Figure 4-28 and Figure The strip chart shws calibratins, sequence steps, and chart anntatin, and many ther features explained in the fllwing sectin. Figure 4-28 Vertical Strip Chart Screen Figure 4-29 Hrizntal Strip Chart Screen 92

94 Strip Chart Scrll Bars Scrll Up/Dwn The Scrll Up/Dwn buttns mve the strip chart either frward r backward at fifteen-minute intervals. Hur The Hur buttns mve the strip chart either frward r backward ne hur. Day The Day buttns mve the strip chart either frward r backward ne day Strip Chart Optins Calibratins Clicking n the Calibratins buttn in a strip chart pens a dialg bx that cntains tw buttns: Calibratin Sequence and Manual Calibratin. The Select Calibratin dialg bx shwn in Figure 4-30 permits users t initiate and cntrl calibratin activities while they are viewing and perating the Strip Chart Prgram. Select Calibratin Figure 4-30 Select Calibratin When the Calibratin Sequence buttn r the Manual Calibratin buttn is pressed, the same Calibratin Sequence r Manual Calibratin dialg bx that is available frm the Initiate Calibratin screen in Sectin will appear. Clicking n the apprpriate buttns n either 93

95 f these tw calibratin dialg bxes will initiate and cntrl a pre-defined calibratin sequence r a manual calibratin activity. Calibratin Sequence The Calibratin Sequence dialg bx shwn in Figure 4-31is the identical dialg bx used in the Calibratin prgram fr initiating and cntrlling a pre-defined calibratin sequence. Users can initiate and cntrl calibratin activities directly within the Strip Chart Prgram. Details abut the peratin and set up f calibratin sequences is prvided in Sectin Figure 4-31 Start Calibratin Sequence while viewing a Strip Chart The Manual Calibratin dialg bx shwn in Figure 4-32 is the identical dialg bx used in the Calibratin prgram fr initiating and cntrlling a manual calibratin activity. 94

96 Figure 4-32 Start Manual Calibratin while viewing a Strip Chart Chart Anntatins The Chart Anntatin feature in the Strip Chart Prgram is used fr making user-anntatins n either Vertical r Hrizntal Strip Charts. Chart anntatins are time-stamped and nce created, becme a permanent part f a pre-defined strip chart. After strip charts are plled and stred n the EMC System Manager central data management system, users in the main ffice are able t view and printut strip chart cntaining anntatins that were made n a strip chart at remte mnitring statins. Figure 4-33 illustrates a chart anntatin n a Hrizntal Strip Chart. Figure 4-33 User Chart Anntatin Hrizntal Strip Chart Figure 4-34 illustrates a chart anntatin n a Vertical Strip Chart. 95

97 Figure 4-34 User Chart Anntatin Vertical Strip Chart Chart Anntatin The fllwing are the prcedures fr making a chart anntatin n a Vertical r Hrizntal Strip Chart. Click n the Anntate buttn t pen the Anntate Dialgue Bx. When the dialg bx is pen, a bx utline will als appear n the strip chart display. Psitin the bx utline by mving r re-psitining the muse n the strip chart. When the utline is in the desired psitin, press the left muse buttn. The utline will nw be changed t the anntatin display bx that has the date and time f the anntatin displayed in it. Click n the Edit buttn and type in the text t be entered int the anntatin display bx. If necessary, it wuld be pssible t resize the anntatin display bx. Click n the Resize/Mve buttn and then psitin the muse pinter ver the utline f the anntatin display bx. When the muse pinter changes t an arrw with tw pints hld dwn the left muse buttn and drag the utline t the desired width/length. Release the muse buttn. It is pssible t mve the anntatin display bx t a different psitin n the strip chart. This is dne by clicking n the Resize/Mve buttn and psitining the muse pinter ver the utline f the anntatin display bx. When the muse pinter changes t a fur-pinted arrw hld dwn the left muse buttn and drag the bx t the desired new psitin. Release the muse buttn. NOTE: Once OK is selected, and the anntatin dialgue bx clses, the anntatin becmes a permanent part f that strip chart. It may nt be edited, resized, mved, r remved after the OK buttn is pressed. If the user presses the Cancel buttn prir t pressing OK, the chart anntatin will be deleted and remved frm the screen. Befre OK can be selected an arrw must be drawn t the part f the strip chart that the anntatin display bx refers t. T d this, click n the Arrw buttn and then click n the relevant part f the strip chart. If a mistake is made (befre OK is selected), simply click n the Arrw buttn again, and then click n the crrect part f the strip chart. The entire arrw will mve. Remve Trace The Remve Trace buttn will remve a desired parameter trace frm the strip chart. T remve a trace: Click n the Remve Trace buttn. Click n that parameter bx that signifies the parameter trace t be remved. The parameter bx shuld nw shw n clr and the trace remved. T return the trace t the screen click n the Remve Trace buttn again. This will return the Strip Charts screen t nrmal viewing. Highlight Trace The Highlight Trace buttn allws a parameter trace t be highlighted. T highlight a trace: Click n the Highlight Trace buttn. 96

98 Click n that parameter bx fr the parameter trace t be highlighted. The parameter bxes and traces f all ther parameters shuld be shwn in light gray, highlighting the ne selected parameter. T und the highlight feature click n the Highlight buttn again. This will return the Strip Chart screen t nrmal viewing. Print Chart The Print Chart buttn is used t print the strip chart selected. T print a chart: Click n the Print Chart buttn. A print bx will pen which lists three ptins: Entire Day, Hr, and Hr. Click n the Print buttn t print, Cancel t quit. Instantaneus The Instantaneus buttn is used t pen the Instantaneus Data Display screen frm the Strip Chart screen. The Instantaneus Data Display is described in Sectin Zm The Zm buttn is used t enlarge a specific prtin f the strip chart fr easier viewing. There are tw different ways t pick a sectin f chart t enlarge. T zm in n a sectin f chart: Click n the Zm buttn. Direct the muse pinter nt the strip chart. Press and hld dwn the left muse buttn. The pinter will change int a bx. Direct the bx t the sectin f chart t be enlarged. Release the muse buttn. The Strip Chart screen will nw enlarge the selected prtin f chart. T define yur wn zm selectin bundaries: Click n the Zm buttn. Direct the muse pinter t the beginning f the area t be enlarged. Press and hld dwn the right muse buttn and mve the pinter. Release the muse buttn. The Strip Chart screen will nw enlarge the selected prtin f chart. T quit the zm feature click the Zm buttn again t return the Strip Chart screen t nrmal viewing. Statin Lgbk The Statin Lgbk buttn allws the lgbk t be pened frm the Strip Chart screen. The Statin Lgbk screen is described in Sectin 4.5. Hrizntal/Vertical The Hrizntal/Vertical buttn is used t change the rientatin f a strip chart. If the strip chart is currently hrizntally riented then the buttn will read vertical. If the strip chart is vertically riented then the buttn will read hrizntal. T change the rientatin f the chart, simply click n the buttn. Dtted/Fine/Bld 97

99 The Dtted buttn is used t change all parameter traces frm fine t dtted line. The Fine buttn is used t change all parameter traces t fine lines. The Bld buttn is used t make all parameter traces bld. Select New Day The Select New Day buttn is used t select a new day fr a Strip Chart. T select a new day: Click n the Select New Day buttn. The Select Day bx will appear. Click n the tggle buttns t select a date. Click OK t view the new chart, select Cancel t quit. Real Time The Real Time buttn is used t view data being recrded at this instant. T view real time data click n the Real Time buttn. 4.5 Statin Lgbk Selecting the Statin Lgbk buttn frm the Statin Manager data lgger Main Menu will pen the Statin Lgbk screen. Click n the Exit buttn lcated at the tp right f the screen t clse the Statin Lgbk screen and return t the Main Menu. The Statin Lgbk is shwn in Figure Figure 4-35 Statin Lgbk Screen The Statin Lgbk screen cnsists f the time and date clumn and the explanatin clumn Statin Lgbk Edit Buttns 98

100 The Statin Lgbk Edit Buttns cnsist f New Entry, Edit Current Entry, Pwer Failure Lg, and Print. New Entry The New Entry buttn is used t enter a new entry int the lgbk. A new windw will appear fr the user t input infrmatin in t the lgbk and a Time Stamp will be lgged with each entry autmatically. Edit Current Entry The Edit Current Entry buttn is used t make changes in previusly made entries. Changes can nly be made t the current day s lgbk. Previus days may nly be viewed. Pwer Failure Lg The Pwer Failure Lg screen is used t recrd and keep track f all pwer failures that ccur at the site. The Pwer Failure Lg screen reprts fr each pwer failure the yearly ttal, the start date and time, the ending date and time, a recrd f wh acknwledged each pwer failure, the duratin, and the number f invalid hurs. T print ut the Pwer Failure Lg screen click n the Print buttn. Fr instructins n the use f the Pwer Failure Lg screen refer t Sectin T leave the Pwer Failure Lg screen at any time click n the Exit buttn lcated at the tp right side f the screen. Print The Print buttn will bring up a separate screen with multiple ptins t print the lgbk entries. Figure 4-36 Print Current Entry allws the user t print the mst recent lgbk entry. Print Current Day allws the user t print the lgbk entry fr the entire day. Print Current Mnth allws the user t print the entire lgbk entry fr the mnth. Print Frm allws the user t select a specific lgbk date range t print. 99

101 Figure 4-36 Print Statin Lgbk 4.6 Initializatin Clicking n the Initializatin buttn frm the Statin Manager data lgger Main Menu will pen the Initializatin menu shwn in Figure The Initializatin Menu prvide authrized useraccess t all f the screens and prgram necessary t set up and initialize a Statin Manager data lgger. The prcedures fr the initial setup f the Statin Manager data lgger are prvided in Sectin

102 The Initializatin Menu cntains six ptins: Figure 4-37 Initializatin Menu Initialize Statin Initialize Reprts Calibratin Cntrl Limits Analg Output Table Initialize Statin The mst frequently used initializatin ptins are available in the Initialize Statin menu. Click n the Initialize Statin buttn t view the menu, shwn in Figure 4-38: Figure 4-38 Initialize Statin Screen Initialize Parameters The Initialize Parameters screen shwn in Figure 4-39 is used t define each data channel recrded by a Statin Manager data lgger. 101

103 Figure 4-39 Initialize Parameters Screen The fllwing is a brief descriptin f the clumns in the Initialize Parameters Table: Parameter the parameter name defined by user r selected frm a list. Averaging Methd the calculatin methd used fr each data channel. Input Chan (Channel) the analg input channel number, r calculated channel. Data Frmat the psitin f the decimal pint in the each recrded data average. Units the engineering units. Full Scale the full-scale value f each data channel in engineering units. Zer the zer value f each data channel in engineering units. Max (Maximum) value the setting fr a high limit flagging f a data channel. Min (Minimum) value the setting fr a lw limit flagging f a data channel. F.S. (Full-Scale) Vlts the maximum vltage input fr each channel. Min (Minimum) Samples number f valid samples needed fr a valid data average. Rate Of Change a setting fr flagging data when ne sample t the next exceeds a value. Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Initialize Parameters screen, click n the Print Table buttn Initialize Plling Table The Initialize Plling screen is used t enter infrmatin related t reginal mdem cmmunicatins, plling and fr naming the initializatin tables. The Initialize Plling screen is shwn in Figure

104 Please Nte: The Statin name entered in the Primary Name bx will identify this cnfiguratin and set up fr the initializatin in the Install and Cpy Utilities screens. A descriptin f the plling fields is as fllws: Figure 4-40 Initialize Plling Screen Primary Statin Name identifies and uniquely names the initializatin files fr this system and prvides the name that is displayed n the screen menu bar. Alternate Statin Name allws fr an additinal name fr plling, such as a unique identifier assigned by an administrating agency. Primary Passwrd fr serial cmmunicatin, accepting up t six alphanumeric characters r blank spaces. Secndary Passwrd available fr system plling by alternate surces such as an administrating agency. Plling ID s prvides fr a numerical cde fr cntrlled access by external plling systems and administrating agencies. Select Operating Mdes - pens the Initialize Cm Prts screen, described in Sectin , which is used t designate the perating mdes fr the Cm Prts. T edit any f these fields, click n the bx next t the title, this will place a cursr inside f the bx, and type in the infrmatin. When cmpleted, click n Exit. Plling changes take effect upn re-starting the system Initialize Statin Table The Initialize Statin screen is used t enter general infrmatin abut the site int a Statin Manager data lgger. Fr mre infrmatin n the Initialize Statin screen, refer t Sectin

105 Initialize Cm Prts Clicking n the Initialize Cm Prts buttn in the Initializatin menu pens the Initialize Cm Prts screen. Fr mre infrmatin n the Instantaneus screen, refer t Sectin Initialize Reprts Selecting Initialize Reprts frm the Initializatin Menu will display the screen shwn in Figure 4-41 belw. This sectin describes hw t frmat 1-hur reprts Reprt Setup Table Figure 4-41 Initialize Reprts Menu The Reprt Setup Table, shwn in Figure 4-42, allws the user t create desired reprts frm the pre-determined list f Reprt Templates prvided. 104

106 Figure 4-42 Schedule Daily Printuts Screen There are multiple reprts types t select frm in the Reprt Setup Table, t begin creating reprts, fllw the directins listed: Click n Edit buttn t begin creating reprts. Click n the New Line buttn t create a new reprt. Select a reprt frmat frm the drp dwn list under Reprt Template. Create a reprt name t be assciated with the desired reprt. Select the parameters desired n the specified reprt. Once all the parameters are selected, click Save Line. Repeat the prcess t create ther reprts Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Reprt Setup table, click n the Print Table buttn Calibratin Cntrl Chart Limits Selecting Calibratin Cntrl Chart Limits frm the Initializatin Menu will display the screen shwn in Figure 4-43 belw. This screen allws the user t set the span percentages used in the Calibratin Cntrl Chart described in Sectin

107 T set a parameter s span percentage: Figure 4-43 Calibratin Cntrl Chart Limits Select Edit Parameter- select ne parameter Calibratin- select the type f calibratin, either Daily Autcals r Precisin Span (%)- indicate the Upper Cntrl limit (UCL), Lwer Cntrl Limit (LCL) and the percentage area t be displayed. Nte: Limits are generally set t 10%, 10% and 20%. Zer (Eng Units)- indicate the UCL, LCL and percentage area t be displayed. Nte: Zer limits are generally set t 5%, 5% and 10-20% Analg Output Table Selecting Analg Output Table frm the Initializatin Menu will display the fllwing table. This table allws the user t set each parameter t a specific analg utput channel. Figure

108 T set a parameter s utput channel: Select Edit Select the Parameter Select the Analg Output Channel Select the desired Vltage Click Save Line Edit Table Figure 4-44 Analg Output Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Analg Output table, click n the Print Table buttn. 4.7 Quality Assurance The Quality Assurance Menu prvides access t quality assurance prgrams that can are available n the Statin Manager data lgger. These prgrams include the Calibratin Cntrl chart and the Excel Exprt prgrams Click n the Quality Assurance buttn n the Statin Manager data lgger Main Menu t pen the Quality Assurance Menu shwn in Figure

109 Figure 4-45 Quality Assurance Menu Screen The Statin Manager data lgger Quality Assurance Menu cntains fur selectins: Calibratin Cntrl Chart Exprt Data t Excel Exprt 15-min Data Calibratin Cntrl Chart The calibratin cntrl chart shwn in Figure 4-46 is used fr visually evaluating and perfrming a quality assurance check f the calibratin zer and span respnses f gaseus analyzers with a Statin Manager data lgger. Sectin prvides details abut perating this prgram. 108

110 Figure 4-46 Calibratin Cntrl Chart Excel Exprts EMC has develped tw custm Excel Macr Prgrams, which are embedded in an Excel.XLA spreadsheet that permits users t easily select mnitring data and imprt and save this data int an Excel spreadsheet. Once data has been saved int Excel, users can cpy the spreadsheet data as a.xls spreadsheet fr use n anther PC. The Statin Manager data lgger can be cnfigured with Micrsft Excel installed. When it is prperly installed, Excel can be launched frm within the Quality Assurance Menu n a Statin Manager data lgger by clicking n the Exprt Data t Excel buttn n this menu. A valid licensed versin f Micrsft Excel must be installed n the Statin Manager data lgger t perate this prgram. EMC can initially supply Micrsft Excel pre-installed n a Statin Manager data lgger, r assist users in upgrading their existing Statin Manager PC t perate Excel. Exprt Data T Excel The Exprt Data t Excel feature is capable f exprting, 1-minute, 5 r 6-minute (depending n the custmer s cnfiguratin), and 1-hur averages. Figure 4-47 illustrates the selectin fields t exprt data t excel. T exprt data t excel, fllw these steps: Select the averaging type, 1-minute, 5 r 6-minute, r 1-hur. Select the frmat in which the exprt will be cnfigured. The single clumn ptin will display all the data in ne clumn. The Data Matrix ptin will display the data in a matrix, fr the entire mnth. Select the desired parameter t exprt. Select the desired Mnth and Year. Select the desired Starting Day t exprt, Starting Hur, and Starting Minute. Select the desired Ending Day t exprt, Ending Hur and Ending Minute. NOTE the ptin t Display Flag and Data at the bttm f the selectin bx. This is a feature fr the user t decide if nly the invalid data s flag shall appear r if the user wuld like the actual value t be displayed with the invalid flag s data. With this ptin NOT selected, nly a flag will be displayed n invalid data. With this ptin selected, BOTH the value and the flag will be displayed n invalid data. 109

111 Figure 4-47 Exprt Data T Excel Exprt 15-Minute Data The Exprt 15-Minute Data requires special cnfiguratins t be set up in rder fr this feature t functin. This prgram is capable f exprting 15-minute data t excel. Please cntact EMC t set up this feature r t find ut if yur system was pre-cnfigured with this ptin. Figure 4-48 illustrates the selectin fields t exprt data t excel. T exprt data t excel, fllw these steps: Select the desired parameter t exprt. Select the desired Mnth and Year. Select the desired Starting Day and Ending Day t exprt. 4.8 Data Figure 4-48 Exprt 15-Minute Data The Data Menu prvides access t the varius types f data display and printut prgrams available in the Statin Manager data lgger. Clicking n the Data buttn frm the Statin Manager data lgger Main Menu will pen the Data Menu shwn in Figure

112 Figure 4-49 Statin Manager Data Menu The Statin Manager data lgger Data Menu cntains eight ptins: Instantaneus Data Tabular Displays Real Time Data Mark Dwn Channels Manual Reprts Scheduled Reprt Reprt Setup Table Reprt Table Data Editr Instantaneus Data Clicking n the Instantaneus Data buttn in the Data Menu will pen the Instantaneus Data screen shwn in Figure This screen displays instantaneus and 1-secnd data fr up t 18 channels f data n ne screen. This screen als displays ther types f data such as the vltage input t each channel, the mst current 1-minute average, the mst current Shrt Term average, the mst current sliding hurly average (is a rlling hurly average based n yur shrt term average values), and the mst current 1-hur clck hurly average. 111

113 Figure 4-50 Instantaneus Data Display Screen Fr a cmplete descriptin f the Instantaneus Data Display Screen, please refer t Sectin Tabular Displays Selecting the Tabular Displays buttn frm the Data Menu will pen the Tabular Displays menu as shwn in Figure 4-51 belw. 112

114 Figure 4-51 Tabular Displays Menu Hur Averages Clicking n the 1-Hur Averages buttn in the Tabular Displays Menu will pen the 1-Hur Averages screen as shwn in Figure 4-52 belw. Figure Hur Averages Screen The 1-Hur Averages screen cnsists f a Real-Time buttn, Histrical buttn, Print Screen buttn, and several data clumns used fr viewing 1-Hur parameter data. At the tp f each f the data clumns are buttns marked either Nne r with a parameter name. Clicking n ne f these buttns will pen a list f parameters t chse frm. Selecting a parameter name will place that name n the buttn and the Statin Manager data lgger will then display that parameters 1-Hur Averages. Real-Time The Real-Time buttn shws the current 1-Hur data as it is being averaged. Histrical The Histrical buttn allws previusly recrded days averages t be viewed in the 1-Hur Averages screen. T select a date: Click n the Histrical buttn t will pen the Select Date bx. Click n either Yesterday r Select Day. If Select Day is selected, tggle arrws will appear. Chse the date using the up and dwn arrws. Click OK t accept, Cancel t quit. 113

115 Print Screen Clicking n the Print Screen buttn t print a cpy f the 1-Hur Averages screen Minute Averages Clicking n the 15-Minute Averages buttn in the Tabular Displays Menu will pen the 15- Minute Averages screen is shwn in Figure 4-53 belw. Figure Minute Averages Screen The 15-Minute Averages screen cnsists f a Real-Time buttn, Histrical buttn, Print Screen buttn, and several data clumns used fr viewing Shrt-Term parameter data. Clicking n Exit at any time will return the Statin Manager data lgger t the Data Menu. At the tp f each f the data clumns are buttns marked either Nne r with a parameter name. Clicking n ne f these buttns will pen a list f parameters t chse frm. Selecting a parameter name will place that name n the buttn and the Statin Manager data lgger will then display that parameter s 15-Minute Averages. Real-Time The Real-Time buttn shws the current 15-Minute data as it is being averaged. Histrical The Histrical buttn allws previusly recrded days averages t be viewed n the 15- Minute Averages screen. T select a date: Click n the Histrical buttn t pen the Select Date bx. 114

116 Click n either Yesterday r Select Day. If Select Day is selected, tggle arrws will appear. Chse the date using the up and dwn arrws. Click n OK t accept, Cancel t clse. Print Screen Clicking n the Print Screen buttn will cause the Statin Manager data lgger t print a cpy f the 15-Minute Averages screen Minute Averages Clicking n the 5-Minute Averages buttn in the Tabular Displays Menu will pen the 5- Minute Averages screen is shwn in Figure 4-54 belw. Figure Minute Averages Screen The 5-Minute Averages screen cnsists f a Real-Time buttn, Histrical buttn, Print Screen buttn, and several data clumns used fr viewing Shrt-Term parameter data. Clicking n Exit at any time will return the Statin Manager data lgger t the Data Menu. At the tp f each f the data clumns are buttns marked either Nne r with a parameter name. Clicking n ne f these buttns will pen a list f parameters t chse frm. Selecting a parameter name will place that name n the buttn and the Statin Manager data lgger will then display that parameter s 5-Minute Averages. Real-Time The Real-Time buttn shws the current 5-Minute data as it is being averaged. Histrical The Histrical buttn allws previusly recrded days averages t be viewed n the 5-Minute Averages screen. T select a date: Click n the Histrical buttn t pen the Select Date bx. 115

117 Click n either Yesterday r Select Day. If Select Day is selected, tggle arrws will appear. Chse the date using the up and dwn arrws. Click n OK t accept, Cancel t clse. Print Screen Clicking n the Print Screen buttn will cause the Statin Manager data lgger t print a cpy f the 5-Minute Averages screen Minute Averages Clicking n the 1-Minute Averages buttn in the Tabular Displays menu will pen the 1- Minute Averages screen as shwn in Figure 4-55 belw. Figure Minute Averages Screen The 1-Minute Averages screen cnsists f a Real-Time buttn, Histrical buttn, Print Screen buttn, and several data clumns used fr viewing 1-Minute parameter data. Clicking n Exit at any time will return The Statin Manager data lgger t the Data Menu. At the tp f each f the data clumns are buttns marked either Nne r with a parameter name. Clicking n ne f these buttns will pen a list f parameters t chse frm. Selecting a parameter name will place that name n the buttn and The Statin Manager data lgger will then display that parameter s 1-Minute Averages. Real-Time The Real-Time buttn shws the current 1-Minute data as it is being averaged. Histrical The Histrical buttn allws previusly recrded days averages t be viewed n the 1-Minute Averages screen. T select a date: 116

118 Click n the Histrical buttn t pen the Select Date bx. Click n either Yesterday r Select Day. If Select Day is selected, tggle arrws will appear. Chse the date using the up and dwn arrws. Click OK t accept, Cancel t clse. Print Screen Clicking n the Print Screen buttn will cause The Statin Manager data lgger t print a cpy f the 1-Minute Averages screen Real Time Data The Real Time Data screen is used as a secndary instantaneus data screen. This screen allws the user t select any cmbinatin f parameters frm the parameter initializatin list t be viewed. This screen als serves as a visual status f bth the parameters reading and Digital Statuses f the input and utput bits. Figure Figure 4-56 Real Time Data T select/switch parameters, simply click n the bx where the parameter name is lcated and select the parameter desired frm the drp dwn menu Mark Dwn Channels The Mark Dwn Channels screen is used t manually mark ne r mre data channels ffline fr a selected default perid f time. Refer t Sectin fr mre infrmatin abut the peratin f this prgram. 117

119 4.8.5 Manual Reprts The Manual Reprts screen allws the user t display, print, r exprt any reprt defined in the Reprt Setup Table. Refer t Sectin fr mre infrmatin abut the peratin f this prgram Scheduled Reprts The Scheduled Reprts screen allws the user t schedule pre-defined reprts t be printed, exprted, r ed ut. Figure 4-57 Print Reprt T schedule a reprt t print autmatically at a specified time, fllw the directins listed. Click Edit. Select the desired Reprt Name frm the drp dwn menu. Nte: Only pre-defined reprts already set up in the Reprt Setup Table will be available, refer t Sectin fr mre infrmatin abut setting up a reprt. Select the desired days the reprt will print ut. Select the desired time yu wuld like the reprt t print, Hurs and Minutes. Multiple hurs may be selected t print the reprt hwever the minutes must remain the same. Select print frm the Actin selectin. Click Save Line. Repeat the steps t set up ther reprts. Exprt T exprt a reprt autmatically at a specified time, fllw the directins listed. Click Edit. Select the desired Reprt Name frm the drp dwn menu. Nte: Only pre-defined reprts already set up in the Reprt Setup Table will be available, refer t Sectin fr mre infrmatin abut setting up a reprt. Select the desired days the reprt will print ut. Select the desired time yu wuld like the reprt t print, Hurs and Minutes. Multiple hurs may be selected t print the reprt hwever the minutes must remain the same. Select the type f frmat yu wuld like t exprt t frm the Actin selectin. Click Save Line. Repeat the steps t set up ther reprts. T a reprt autmatically at a specified time, fllw the directins listed. Click Edit. Select the desired Reprt Name frm the drp dwn menu. Nte: Only pre-defined reprts already set up in the Reprt Setup Table will be available, refer t Sectin fr mre infrmatin abut setting up a reprt. Select the desired days the reprt will print ut. 118

120 Select the desired time yu wuld like the reprt t print, Hurs and Minutes. Multiple hurs may be selected t print the reprt hwever the minutes must remain the same. Select Exprt t PDF frm the Actin selectin. Refer t Sectin n hw t set up the addresses the Reprts will be t. Click Save Line. Repeat the steps t set up ther reprts Reprt Setup Table Figure 4-57 Scheduled Reprts Table The Reprt Setup screen allws the user t create desired reprts frm the pre-determined list f Reprt Templates prvided. Refer t Sectin fr mre infrmatin abut the peratin f this prgram Reprt Table The Reprt screen allws the user t set up the desired addresses f the recipients the s will g ut t. Figure 4-58 T set up the addresses and the reprt t be ed, fllw the instructins listed. Click Edit. Type in a Reprt Name which will appear as the Subject line n the . Type in the File Name, which must match the file name being exprted. Therefre if the user created a reprt t be called Daily Averages in the Reprt Setup Table, the File Name must be Daily Averages.pdf. Type in the Recipient s address. 119

121 If the user wuld like this reprt t be CC d t ther peple, type in the CC List the addresses f the ther recipients separating each address using <>;<>. In the example shwn belw, <ctsu@emcsl.cm>;<test@gmail.cm>. Click Save Line. Repeat the steps if ther reprts are t be ed ut as well Data Editr Figure 4-58 Schedule Daily Printuts Screen The Data Editr screen allws the user t manually edit histrical Hurly data. Ntice there are 3 ways t change data, Figure 4-59: a) Yu can edit multiple hurs f data by multiplying the current data by a certain factr. b) Yu can replace a single hur s wrth f data. c) Yu can edit the flags n the data. 120

122 Figure 4-59 Data Editr Edit Multiple Hurs Select the parameter yu wish t edit frm the drp dwn menu. Select the starting Day and Time fr which yu want t start changing the data and an ending Day and Time. Anything selected in that time frame including the actual selected date and time will be changed. Enter in a multiplying number. This is the value yu wish t multiple the current data by. Click Execute. This will g thrugh and multiply the data by the entered value and recalculate the hurly data. If yu click n View Lg, it will shw yu a histry f everything that has been dne Replace Single Hur Select the parameter yu wish t edit frm the drp dwn menu. Select the Day and Hur f the data in which yu want t replace. Enter the new value t replace the selected hur s data. Click Execute. This will g thrugh and replace the selected hur s data by the entered value and recalculate the hurly data. If yu click n View Lg, it will shw yu a histry f everything that has been dne Replace Flag(s) Select the parameter yu wish t edit frm the drp dwn menu. Select the starting Day and Time fr which yu want t start changing the data and an ending Day and Time. Anything selected in that time frame including the actual selected date and time will be changed. Under Flags, select the flag yu want t be replaced. 121

123 Under Replacement, select the flag yu want the current ne t be replaced with. Click Execute. This will g thrugh and replace the selected flag with the new flag and recalculate the hurly data based n the flag s validity. ***Refer t Statin Manager Validity Flag List*** If yu click n View Lg, it will shw yu a histry f everything that has been dne. 4.9 Alarms The Alarms prgram in the Statin Manager data lgger prvides alarm and warning status ntificatins based n pre-defined events. When a Statin Manager data lgger detects an alarm r warning cnditin based n the user-defined criteria in the Parameter Alarm Table, it will create an event recrd in the Alarm Histry table and perfrm the functin identified in the Alarm Parameter table. The user may identify ne f tw levels - Warning r Alarm - and initiate a specific functin fr the required respnse. Fr ntificatins, the Statin Manager data lgger is capable f activating a digital utput status, sending pager messages, transmissin f fax messages, transmissin f s, and can supprt vice dialing ntificatins. The Digital Output feature may be used t activate relay-cntrlled equipment such as an audible r visual warning device. The Paging feature may ntify key persnnel f an unusual event r cnditin requiring interventin. The transmissin f faxes r s is a gd way t keep track f alarm histry events withut having t be n site. The vice dialing feature is a great way t immediately ntify any key persnnel f all the details entailed in the unusual event r cnditin requiring interventin. Figure Parameter Alarm Table Figure 4-60 Alarm System Menu The Parameter Alarm table allws the user t define the parameters that trigger an Alarm r Warning cnditin. Figure

124 Figure 4-61 Parameter Alarm Table Use the fllwing t initialize an Alarm r Warning: Select the On/Off cnditin - click n the chice fr the alarm. Select the Parameter - a pull dwn screen will identify the initialized parameters and the user may chse a parameter fr the alarm by clicking n the selectin. Select the Data Type - a pull dwn screen will identify the available perids and the user may click n the timing chice fr the alarm cnditin. Select the Rule clumn - less than, greater than and/r equal t the assigned threshld is displayed in a pull dwn bx. Select the Threshld - this will allw the user t enter an empirical number fr the parameter. Select the type f alarm - Warning r Alarm, based n the user-defined criteria fr these terms. This selectin des nt change the available actins fr the parameter. Select the Actin clumn - Call Pager and Enable Digital Output are supprted n general release versins with the additinal chices available n custmized versins f the Statin Manager data lgger. Select Recipient - enter the name identifier frm the Alarm Telephne table fr the intended receiver f the actin. This selectin will als define the digital utput line t relay-cntrlled equipment, such as an audible r visual warning device. After cmpleting the edit, use the Save Line feature t enter the infrmatin int the Parameter Alarm table. The Alarm will becme available when the Statin Manager data lgger is re-started. Clicking n the Print buttn prints the displayed Parameter Alarm table Parameter Definitins Table This feature allws the user t input specific details fr each parameter including the analyzer s make and mdel number. This infrmatin is the transferred ver t the alarm functin allwing the recipient f the t have specific details f the parameter and analyzer in alarm cnditin. Figure

125 4.9.3 Alarm Update Table Figure 4-62 Parameter Definitins Table The Alarm Update table will allw the user t set the frequency f ntificatin fr the alarm cnditin based n the selected average interval. After Every Interval will cause the Statin Manager data lgger t take actin with each alarm event, and After First Interval will effect actin nly after the first event. The Statin Manager data lgger will cntinue t lg the events in the Alarm Histry table fr user reference. The Alarm Update table cntrls the Actin clumn f the Alarm Parameter table. Figure

126 Figure 4-63 Alarm Update Table Relay Cnditin Table The Relay Cnditin table allws the user t trigger a digital utput (relay) t clse based n a pre-defined parameter threshld. This feature, if desired, will allw the user t trigger an audible alarm, visual alarm, r in certain applicatins can trigger a pump t cme n. Figure 4-64 Figure 4-64 Relay Cnditin Table 125

127 Select the Parameter - a pull dwn screen will identify the initialized parameters and the user may chse a parameter fr the alarm by clicking n the selectin. Select the Rule clumn - less than, greater than and/r equal t the assigned threshld is displayed in a pull dwn bx. Select the Threshld - this will allw the user t enter an empirical number fr the parameter. Select the Digital Output - channel t be triggered based n the alarm. Click Save Line Alarm Telephne Table The Alarm Telephne table allws the user t custmize the character data string sent t a pager. Figure 4-65 Figure 4-65 Alarm Telephne Table Use the fllwing infrmatin t setup a pager device: Select Recipient and enter a unique name identifier fr the ntificatin. Select Device and click n Pager in the pull-dwn screen. The ther listed devices are nly available n custmized versins f the Statin Manager data lgger. Select the Leading clumn fr entering number cdes required fr accessing an utside line frm a PBX system. This clumn may be left blank if nt required. Select the Telephne Number clumn and enter the number t be called; the Statin Manager data lgger will ignre nn-numerical characters such as. Select the Wait perid and a pull dwn screen will present a tggle t select the number f secnds fr delay befre dialing the pager string. This wait perid is typically 3 t 5 secnds but depends n the lcal telephne cnnectin speed r the paging system requirements. 126

128 Select Pager String t enter the numerical message t be delivered. The Statin Manager data lgger will supprt the and # keys fr this feature. Certain paging systems may require additinal access cdes, such as a PIN, and the additinal Wait perid and Pager String clumn is prvided t supprt these systems. These additinal clumns may be left blank if nt required. After cmpleting the edit, use the Save Line feature t enter the infrmatin int the Alarm Telephne table Digital Input Alarm Table The Digital Input Alarm table allws the user t establish an alarm based n the digital utput sent frm anther system. Based n the status f the digital input, anything capable f sending ut a vltage greater than 5 V is capable f triggering an alarm. Figure 4-66 Figure 4-66 Digital Input Alarm Table Select the On/Off cnditin - click n the chice fr the alarm. Select the Digital Input click n the crrespnding input channel the alarm is wired t. Select the Crrespnding Cnditin always select nne. Select the Actin click the desired actin based n the input alarm. Select the Recipient select the name identifier fr the intended receiver f the actin. Select the Message always select N/A Digital Input Message Table 127

129 This feature enables the user t input the desired message t be displayed fr the crrespnding alarm set in the Digital Input Alarm Table. Figure 4-67 Figure 4-67 Digital Input Message Table Select the Number the crrespnding digital input channel the alarm message is assciated t. Select the Message input the desired alarm message t be displayed in assciatin t the digital input alarm table Alarm Histry Table With the trigger f an Alarm r Warning cnditin, the Statin Manager data lgger recrds the event in the Alarm Histry table, including the date and time f the ccurrence and the selected parameters. Subsequent alarm events will be recrded t the table, but ntificatins r digital utput is based n the Alarm Update table. Figure

130 Figure 4-68 Alarm Histry Table Line items in the Alarm Histry table may be deleted by clicking n the Delete buttn f the table; the system will prmpt the user t select a line item and will delete recrds up t and including the selected line. Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f this screen, click n the Print Table buttn Cnditin Flag Table The Cnditin Flag table allws users t set a threshld cnditin in which a parameter will be flagged as invalid until the triggering parameter s cnditin is met. Figure

131 Figure 4-69 Cnditin Flag Table T set a parameter s cnditin requirements fr flagging: Select the Parameter - a pull dwn screen will identify the initialized parameters and the user may chse a parameter fr the alarm by clicking n the selectin. Select the Cnditin - less than, greater than and/r equal t the assigned threshld is displayed in a pull dwn bx. Select the Value input the threshld value in which the secnd parameter will be flagged as invalid. Set the Parameter Flagged click n the secnd parameter which will be flagged based n the first parameter s cnditin. Save line Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy click n the Print Table buttn Alarm Table The alarm allws the user t set up the recipients wh will receive alarm s when alarms ccur. Figure

132 Figure 4-70 Alarm Table Select the Name input a name identifier fr the recipient. Select the Recipient input the recipient s address. Select the CC List if the alarm needs t g t mre than ne recipient, the CC List may be used. T input mre than ne address in the CC List, separate each address with <>;<>. i.e. <ctsu@emcsl.cm>;<test@gmail.cm> Click Save Line Utilities The Utilities Menu prvides access t several utilities and prgrams, such as the Statin Manager data lgger Security System and Archive prgrams. It als includes several Micrsft Windws utilities, including the Windws prgram fr setting the PC date and the Micrsft Windws Calculatr prgram. Clicking n the Utilities buttn in the Statin Manager data lgger Main Menu will pen the Utilities Menu shwn in Figure

133 The Utilities Menu cntains seven ptins: Figure 4-71 Utilities Menu Screen Security System Calculatr Date and Time Autmated Data Backup Security System Clicking n the Security System buttn frm the Utilities Menu pens the Security System Menu as shwn in Figure Access t many f the menu selectins in the Security System Menu is restricted accrding t what user grup the currently lgged-in user is assigned. If the permissins fr that particular user are nt set t allw the user access, then the message Permissin Denied will appear n the screen. 132

134 Figure 4-72 Security System Menu When setting up the Security System in a Statin Manager data lgger, begin by defining the permissins, then define grups, and then define users. Each successive screen uses definitins r names that are defined in the previus screen Define Users Clicking n the Define Users buttn frm the Security System Menu pens the Define Users table. If a user des nt have permissin t view this screen, then the message Permissin Denied will appear n the screen. The Define Users table lists fr each user allwed int the system, their User Name, Initials, Passwrd, Time Out, and Grup Name. If Grup Names have nt already been defined, exit the Define Users screen and enter the Define Grups screen (explained in sectin ). Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Define Users screen click n the Print Table buttn Define Grups Clicking n the Define Grups buttn frm the Security System Menu pens the Define Grups table, as shwn in Figure If a user des nt have permissin t view this screen, then the message Permissin Denied will appear n the screen. 133

135 Figure 4-73 Define Grups Screen The Define Grups table cntains tw clumns. The first clumn lists the different Grup Names. The secnd clumn lists all f the Permissins that are granted t each f the Grups Names. There may be several different permissins listed fr each grup name. These permissins will have been defined frm the Permissins screen. If Permissins have nt already been defined, exit the Define Grups screen and enter the Define Permissins screen (explained in sectin ). Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Define Grups screen click n the Print Table buttn Define Permissins Clicking n the Define Permissins buttn frm the Security System Menu pens the Define Permissins table, as shwn in Figure If a user des nt have permissin t view this screen, the message Permissin Denied will appear. 134

136 Figure 4-74 Define Permissins Table The Define Permissins table cntains three clumns. The first clumn is the Permissin Name. The secnd clumn is the Screen Name clumn. The third clumn is the Edit/View clumn. In this screen, ne permissin name is defined fr ne r mre different statin names. This permissin name will then later be used in the Define Grups table t define what type f access each grup will have. Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Define Permissins screen click n the Print Table buttn Define Screens Clicking n the Define Screens buttn frm the Security System Menu pens the Define Screens table, as shwn in Figure The Define Screens table ties a screen name t the executable file name. This table cntains tw clumns: Screen Name and Executable Name. 135

137 Figure 4-75 Define Screen Table Edit Table Refer t Appendix A fr the prcedures t use the edit mde sectin fr this and all ther tables. Print Table T print a cpy f the Define Screen Table click n the Print Table buttn Calculatr Clicking n the Calculatr buttn frm the Utilities Menu will pen the calculatr. Figure

138 Figure 4-76 Calculatr Screen This Calculatr is perated identically t any regular calculatr. There are tw different calculatr types: Scientific and Standard. Select which type t use by clicking n the Calculatr s view menu, and then clicking n either scientific r standard. T clse the calculatr click n the minus sign bx in the upper left crner f the calculatr bx. Click n Clse. The Statin Manager data lgger will return t the Utilities Menu Date and Time Clicking n the Date and Time buttn in the Utilities Menu pens the Date/Time Bx. The Date/Time Bx is used t display and set the date and time. Figure

139 Figure 4-77 Date and Time Screen Date The Date bx displays the current date with a mnthly calendar. The mnth is changed by a pull dwn list and the year is changed by clicking n the up and dwn arrw buttns lcated n the right side f the year bx. The day is selected by clicking n the calendar date desired. Time The Time bx displays the current time and allws it t be changed by clicking n the up and dwn arrw buttns lcated n the right side f the bx. The user may als directly enter the time in the bx. Click n OK t restart the clck. Time Zne The Time Zne bx displays the time zne fr the time displayed in the Date/Time bx. It als allws the time zne t be changed by clicking n the arrw buttn n the right side f the Time Zne bx and then selecting a new time zne designatin. The Autmatically adjust clck fr daylight saving changes shuld never be selected. Internet Time The Internet Time allws the user t sync the PC clck with an Internet Time server. This feature will sync with the Internet server nce a week t ensure the PC s clck is crrect. This functin nly wrks if the PC is cnnected t the internet via TCP/IP. Click n OK t accept all settings, Cancel t quit Autmatic Data Backup The Autmatic Data Backup prgram is used t schedule autmatic backups f all the critical files necessary t rebuild the Statin Manager PC shuld anything happen t it. This feature 138

140 als enables the user t manually back up all the data, which backs up exactly the same infrmatin as the autmatic backup wuld. Figure 4-78 Figure 4-78 Manual Data Backup Screen T aut archive data: By default, this feature is disabled. Select enable t begin the autmatic backup. Select the time the backup wuld take place. Select hw ften the backup is t ccur. This ptin can range frm 00 which will back up every day t as lng as 29 which will back up nce a mnth. Select the Drive the backup is t stre the data. By default this is set t the CD-ROM drive hwever can be changed t any media type including a Flash Drive. T manually archive data: Select the Drive the backup is t stre the data. By default this is set t the CD-ROM drive hwever can be changed t any media type including a Flash Drive. Click n Manual Backup. When clicked, the backup prcess will begin immediately Pwer Failures The Pwer Failure Lg is the lg file that cntains all f the pwer failures that are recrded n a Statin Manager data lgger. In additin t recrding pwer failures in this lg file, the Statin Manager data lgger als writes a recrd f each pwer failure in the Statin Manager Lgbk. Clicking n the Pwer Failures buttn in the Statin Manager data lgger Main Menu pens the Pwer Failure Lg Screen shwn in Figure