Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
|
|
- Wesley Snow
- 5 years ago
- Views:
Transcription
1 FEATURES Very low voltage noise 2.8 nv/ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain: 2 db Wide bandwidth: MHz typical ±5 V to ±8 V operation APPLICATIONS Precision instrumentation PLL filters Laser diode control loops Strain gage amplifiers Medical instrumentation Thermocouple amplifiers Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp PIN CONFIGURATIONS OUT A IN A 2 +IN A 3 V 4 TOP VIEW (Not to Scale) 8 V+ 7 OUT B 6 IN B 5 +IN B Figure. 8-Lead SOIC_N (R-8) OUT A IN A 2 +IN A 3 V 4 TOP VIEW (Not to Scale) 8 V+ 7 OUT B 6 IN B 5 +IN B Figure 2. 8-Lead MSOP (RM-8) GENERAL DESCRIPTION The precision operational amplifier offers ultralow offset, drift, and voltage noise combined with very low input bias currents over the full operating temperature range. The is a precision, wide bandwidth op amp featuring railto-rail output swings and very low noise. Operation is fully specified from ±5 V to ±5 V. The features a rail-to-rail output like that of the OP84, but with wide bandwidth and even lower voltage noise, combined with the precision and low power consumption like that of the industry-standard OP7 amplifier. Unlike other low noise, rail-to-rail op amps, the has very low input bias current and low input current noise. With typical offset voltage of only 2 μv, offset drift of.2 μv/ C, and noise of only. μv p-p (. Hz to Hz), the is perfectly suited for applications where large error sources cannot be tolerated. Precision instrumentation, PLL and other precision filter circuits, position and pressure sensors, medical instrumentation, and strain gage amplifiers benefit greatly from the very low noise, low input bias current, and wide bandwidth. Many systems can take advantage of the low noise, dc precision, and rail-to-rail output swing provided by the to maximize SNR and dynamic range. The smaller packages and low power consumption afforded by the allow maximum channel density or minimum board size for space-critical equipment. The is specified for the extended industrial temperature range ( 4 C to +25 C). The is available in the 8-lead MSOP, and the popular 8-lead, narrow SOIC; both of which are lead-free packages. MSOP packaged devices are only available in tape and reel format. For the single version of this ultraprecision, rail-to-rail op amp, see the AD8675 data sheet. The AD8675 and are members of a growing series of low noise op amps offered by Analog Devices, Inc. Table. Voltage Noise Package.9 nv. nv.8 nv 2.8 nv 3.8 nv Single AD797 AD8597 ADA44- AD8675 AD867 Dual AD8599 ADA44-2 AD8672 Quad ADA44-4 AD8674 Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 96, Norwood, MA , U.S.A. Tel: Fax: Analog Devices, Inc. All rights reserved.
2 TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Electrical Specifications... 3 Absolute Maximum Ratings...5 Thermal Resistance...5 Power Sequencing...5 ESD Caution...5 Typical Performance Characteristics...6 Outline Dimensions... Ordering Guide... REVISION HISTORY 8/ Rev. B to Rev. C Change to Y-Axis Label, Figure /9 Rev. A to Rev. B Changes to General Description Section... Added Table ; Renumbered Sequentially... Updated Outline Dimensions... Changes to Ordering Guide... 4/8 Rev. to Rev. A Changes to Table... 3 Changes to Table Changes to Figure 6, Figure 7, Figure Changes to Figure 9 through Figure Changes to Figure 2, Figure 22, and Figure Added Figure 26, Renumbered Sequentially... 9 Changes to Figure Added Figure 28, Renumbered Sequentially... /6 Revision : Initial Version Rev. C Page 2 of 2
3 SPECIFICATIONS ELECTRICAL SPECIFICATIONS VS = ±5. V, VCM = V, VO = V, TA = +25 C, unless otherwise specified. Table 2. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS B Grade (SOIC) 2 μv B Grade (MSOP) 6 μv A Grade (SOIC, MSOP) μv Offset Voltage VOS 4 C TA +25 C B Grade (SOIC, MSOP) 5 6 μv A Grade (SOIC, MSOP) 2 μv Input Bias Current IB 2 +2 na 4 C TA +25 C na Input Offset Current IOS + na 4 C TA +25 C na Input Voltage Range V Common-Mode Rejection Ratio CMRR VCM = 3. V to +3. V 5 3 db 4 C TA +25 C 5 db Open-Loop Gain AVO RL = 2 kω to ground, 2 26 db VO = 3.5 V to +3.5 V 4 C TA +25 C 7 db Offset Voltage Drift ΔVOS/ΔT 4 C TA +25 C.2.6 μv/ C OUTPUT CHARACTERISTICS Output Voltage High VOH RL = kω to ground V 4 C TA +25 C V RL = 2 kω to ground V 4 C TA +25 C V Output Voltage Low VOL RL = kω to ground V 4 C TA +25 C 4.85 V RL = 2 kω to ground V 4 C TA +25 C 4.82 V Short-Circuit Limit ISC +4 ma Output Current IO ±2 ma POWER SUPPLY Power Supply Rejection Ratio PSRR VS = ±5. V to ±5. V 6 2 db 4 C TA +25 C 6 2 db Supply Current/Amplifier ISY VO = V ma 4 C TA +25 C 3.8 ma DYNAMIC PERFORMANCE Slew Rate SR RL = 2 kω 2.5 V/μs Gain Bandwidth Product GBP MHz NOISE PERFORMANCE Voltage Noise en p-p. Hz to Hz. μv p-p Voltage Noise Density en f = khz 2.8 nv/ Hz Current Noise Density in f = Hz.3 pa/ Hz Rev. C Page 3 of 2
4 VS = ±5 V, VCM = V, VO = V, TA = +25 C, unless otherwise specified. Table 3. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS B Grade (SOIC) 2 μv B Grade (MSOP) 6 μv A Grade (SOIC, MSOP) μv Offset Voltage VOS 4 C TA +25 C B Grade (SOIC, MSOP) 5 6 μv A Grade (SOIC, MSOP) 2 μv Input Bias Current IB 2 +2 na 4 C TA +25 C na Input Offset Current IOS + na 4 C TA +25 C na Input Voltage Range V Common-Mode Rejection Ratio CMRR VCM = 2.5 V to +2.5 V 3 db 4 C TA +25 C 7 3 db Open-Loop Gain AVO RL = 2 kω to ground, db VO = 3.5 V to +3.5 V 4 C TA +25 C 7 db Offset Voltage Drift ΔVOS/ΔT 4 C TA +25 C.2.6 μv/ C OUTPUT CHARACTERISTICS Output Voltage High VOH RL = kω to ground V 4 C TA +25 C +4.8 V RL = 2 kω to ground V 4 C TA +25 C +4.4 V Output Voltage Low VOL RL = kω to ground V 4 C TA +25 C 4.9 V RL = 2 kω to ground V 4 C TA +25 C 4.6 V Short-Circuit Limit ISC +4 ma Output Current IO ±2 ma POWER SUPPLY Power Supply Rejection Ratio PSRR VS = ±5. V to ±5. V 6 2 db 4 C TA +25 C 6 db Supply Current/Amplifier ISY VO = V ma 4 C TA +25 C 4.2 ma DYNAMIC PERFORMANCE Slew Rate SR RL = kω 2.5 V/μs Gain Bandwidth Product GBP MHz NOISE PERFORMANCE Voltage Noise en p-p. Hz to Hz. μv p-p Voltage Noise Density en f = khz 2.8 nv/ Hz Current Noise Density in f = Hz.3 pa/ Hz Rev. C Page 4 of 2
5 ABSOLUTE MAXIMUM RATINGS Table 4. Parameter Rating Supply Voltage ±8 V Input Voltage ±V supply Differential Input Voltage ±.7 V Output Short-Circuit Duration to GND Indefinite Storage Temperature Range RM, R Packages 65 C to + C Operating Temperature Range 4 C to +25 C Junction Temperature Range RM, R Packages 65 C to + C Lead Temperature Range (Soldering, sec) 3 C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE Table 5. Thermal Resistance Package Type θja θjc Unit 8-Lead MSOP (RM) 2 45 C/W 8-Lead SOIC_N (R) C/W POWER SEQUENCING The op amp supplies must be established simultaneously with, or before, any input signals are applied. If this is not possible, the input current must be limited to ma. ESD CAUTION Rev. C Page 5 of 2
6 TYPICAL PERFORMANCE CHARACTERISTICS ±5 V and ±5 V, TA = 25 C, unless otherwise specified. VOLTAGE NOISE DENSITY (nv/ Hz) V OS (µv) TYPICAL V S = ±5V k k k FREQUENCY (Hz) Figure 3. Voltage Noise Density vs. Frequency Figure 6. Offset Voltage vs. Temperature NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS V OS (µv) I B (na) Figure 4. Input Offset Voltage Distribution Figure 7. Input Bias Current, VSY = ±5 V NUMBER OF AMPLIFIERS 5 NUMBER OF AMPLIFIERS T C V OS (µv/ C) I B (na) Figure 5. TCVOS Distribution Figure 8. Input Bias Current, VSY = ±5 V Rev. C Page 6 of 2
7 ±5 V and ±5 V, TA = 25 C, unless otherwise specified. I B (na) V S = ±5V V S = ±5V GAIN (db) GAIN PHASE C L = 35pF θ M = PHASE MARGIN (Degrees) Figure 9. Input Bias Current vs. Temperature k k k M M FREQUENCY (Hz) Figure 2. Gain and Phase vs. Frequency 8 M SUPPLY CURRENT (ma) CLOSED-LOOP GAIN (db) G = G = G = SUPPLY VOLTAGE (V) Figure. Supply Current vs. Total Supply Voltage k k k M M M FREQUENCY (Hz) Figure 3. Closed-Loop Gain vs. Frequency SUPPLY CURRENT (ma) V S = ±5V V S = ±5V Z OUT (Ω) A VO = A VO = A VO = Figure. Supply Current vs. Temperature k k k M M M FREQUENCY (Hz) Figure 4. ZOUT vs. Frequency Rev. C Page 7 of 2
8 ±5 V and ±5 V, TA = 25 C, unless otherwise specified. 5 V IN = ±V A V = +. V IN 4 VOLTAGE (V) 5 5 INPUT VOLTAGE (V) V OUT 3 2 OUTPUT VOLTAGE (V) 5 TIME (µs/div) Figure 5. Large Signal Transient Response, VSY = ±5 V V IN = 2mV p-p A VO = R L = kω TIME (µs) Figure 8. Positive Overvoltage Recovery V IN = ±3.5V A V = V IN = 2mV p-p A VO = R L = kω 4 VOLTAGE (V) 2 2 INPUT VOLTAGE (V) V IN V OUT 3 2 OUTPUT VOLTAGE (V) TIME (µs/div) Figure 6. Large Signal Transient Response, VSY = ±5 V TIME (µs) Figure 9. Negative Overvoltage Recovery A V = + V IN = mv p-p OVERSHOOT (%) OS OS CMRR (db) k k k CAPACITANCE (pf) Figure 7. Small Signal Overshoot vs. Load Capacitance k k k M M FREQUENCY (Hz) Figure 2. CMRR vs. Frequency M Rev. C Page 8 of 2
9 ±5 V and ±5 V, TA = 25 C, unless otherwise specified. 6 POWER SUPPLY REJECTION RATIO (db) PSRR PSRR V S V OUT (mv) SOURCE SINK 2 k k k M M FREQUENCY (Hz) Figure 2. Power Supply Rejection Ratio vs. Frequency M LOAD CURRENT (ma) Figure 24. Output Saturation Voltage vs. Output Load Current POWER SUPPLY REJECTION RATIO (db) HIGH OUTPUT VOLTAGE (V) V S = ±5V Figure 22. Power Supply Rejection Ratio vs. Temperature Figure 25. High Output Voltage, VOH vs. Temperature, VS = ±5 V NOISE (µv) HIGH OUTPUT VOLTAGE (V) V S = ±5V TIME (s) Figure 23. Voltage Noise (. Hz to Hz) Figure 26. High Output Voltage, VOH vs. Temperature, VS = ±5 V Rev. C Page 9 of 2
10 ±5 V and ±5 V, TA = 25 C, unless otherwise specified V S = ±5V V S = ±5V LOW OUTPUT VOLTAGE (V) LOW OUTPUT VOLTAGE (V) Figure 27. Low Output Voltage, VOL vs. Temperature, VS = ±5 V Figure 28. Low Output Voltage, VOL vs. Temperature, VS = ±5 V Rev. C Page of 2
11 OUTLINE DIMENSIONS 5. (.968) 4.8 (.89) 4. (.574) 3.8 (.497) (.244) 5.8 (.2284).25 (.98). (.4) COPLANARITY. SEATING PLANE.27 (.) BSC.75 (.688).35 (.532).5 (.2).3 (.22) 8.25 (.98).7 (.67). (.96).25 (.99).27 (.).4 (.57) 45 COMPLIANT TO JEDEC STANDARDS MS-2-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 247-A PIN IDENTIFIER.65 BSC COPLANARITY MAX 6 5 MAX.23.9 COMPLIANT TO JEDEC STANDARDS MO-87-AA Figure 3. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters B ORDERING GUIDE Model Temperature Range Package Description Package Option Branding ARMZ 4 C to +25 C 8-Lead Mini Small Outline Package [MSOP] RM-8 A3 ARMZ-REEL 4 C to +25 C 8-Lead Mini Small Outline Package [MSOP] RM-8 A3 ARZ 4 C to +25 C 8-Lead Standard Small Outline Package [SOIC_N] R-8 ARZ-REEL 4 C to +25 C 8-Lead Standard Small Outline Package [SOIC_N] R-8 ARZ-REEL7 4 C to +25 C 8-Lead Standard Small Outline Package [SOIC_N] R-8 BRMZ 4 C to +25 C 8-Lead Mini Small Outline Package [MSOP] RM-8 AL BRMZ-REEL 4 C to +25 C 8-Lead Mini Small Outline Package [MSOP] RM-8 AL BRZ 4 C to +25 C 8-Lead Standard Small Outline Package [SOIC_N] R-8 BRZ-REEL 4 C to +25 C 8-Lead Standard Small Outline Package [SOIC_N] R-8 BRZ-REEL7 4 C to +25 C 8-Lead Standard Small Outline Package [SOIC_N] R-8 Z = RoHs Compliant Part. Rev. C Page of 2
12 NOTES 26 2 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D /(C) Rev. C Page 2 of 2
Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
Ultraprecision, 36 V, 2. nv/ Hz Dual Rail-to-Rail Output Op Amp AD676 FEATURES Very low voltage noise: 2. nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage:
More informationLow Power, Precision, Auto-Zero Op Amps AD8538/AD8539 FEATURES Low offset voltage: 13 μv maximum Input offset drift: 0.03 μv/ C Single-supply operatio
Low Power, Precision, Auto-Zero Op Amps FEATURES Low offset voltage: 3 μv maximum Input offset drift:.3 μv/ C Single-supply operation: 2.7 V to 5.5 V High gain, CMRR, and PSRR Low input bias current: 25
More informationDual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
More information16 V, 4 MHz RR0 Amplifiers AD8665/AD8666/AD8668
6 V, MHz RR Amplifiers AD8665/AD8666/AD8668 FEATURES Offset voltage:.5 mv max Low input bias current: pa max Single-supply operation: 5 V to 6 V Dual-supply operation: ±.5 V to ±8 V Low noise: 8 nv/ Hz
More informationMicropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
More information15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
More informationLow Cost, Precision JFET Input Operational Amplifiers ADA4000-1/ADA4000-2/ADA4000-4
Low Cost, Precision JFET Input Operational Amplifiers ADA-/ADA-/ADA- FEATURES High slew rate: V/μs Fast settling time Low offset voltage:.7 mv maximum Bias current: pa maximum ± V to ±8 V operation Low
More informationAD8613/AD8617/AD8619. Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers PIN CONFIGURATIONS FEATURES APPLICATIONS
Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers FEATURES Offset voltage: 2.2 mv maximum Low input bias current: pa maximum Single-supply operation:.8 V to 5 V Low
More informationLow Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
More informationLow Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Low Cost JFET Input Operational Amplifiers ADTL/ADTL FEATURES TL/TL compatible Low input bias current: pa maximum Offset voltage 5.5 mv maximum (ADTLA/ADTLA) 9 mv maximum (ADTLJ/ADTLJ) ±5 V operation Low
More informationTABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum
FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input
More information4 MHz, 7 nv/ Hz, Low Offset and Drift, High Precision Amplifier ADA EP
Enhanced Product FEATURES Low offset voltage and low offset voltage drift Maximum offset voltage: 9 µv at TA = 2 C Maximum offset voltage drift:.2 µv/ C Moisture sensitivity level (MSL) rated Low input
More informationAD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
More informationLow Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Preliminary Technical Data FEATURES TL082 / TL08 compatible Low input bias current: 0 pa max Offset voltage: 5mV max (ADTL082A/ADTL08A) 9 mv max (ADTL082/ADTL08) ±5 V to ±5 V operation Low noise: 5 nv/
More informationSingle and Dual, Ultralow Distortion, Ultralow Noise Op Amps AD8597/AD8599 PIN CONFIGURATIONS FEATURES APPLICATIONS
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps FEATURES Low noise:. nv/ Hz at khz Low distortion: db THD @ khz Input noise,. Hz to Hz:
More information16 V, 1 MHz, CMOS Rail-to-Rail Input/Output Operational Amplifier ADA4665-2
6 V, MHz, CMOS Rail-to-Rail Input/Output Operational Amplifier ADA4665-2 FEATURES Lower power at high voltage: 29 μa per amplifier typical Low input bias current: pa maximum Wide bandwidth:.2 MHz typical
More information24 MHz Rail-to-Rail Amplifiers with Shutdown Option AD8646/AD8647/AD8648
24 MHz Rail-to-Rail Amplifiers with Shutdown Option AD8646/AD8647/AD8648 FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew
More information150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
More informationDual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482 FEATURES High slew rate: 9 V/μs Wide bandwidth: 4 MHz Low supply current: 2 μa/amplifier maximum Low offset voltage: 3 mv maximum
More informationPrecision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608
Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608 FEATURES Low offset voltage: 65 μv maximum Low input bias currents: pa maximum Low noise: 8 nv/ Hz Wide
More information1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-2
.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA45-2 FEATURES Very low supply current: 3 μa Low offset voltage: 5 μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8 V
More informationDual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP22/OP42 FEATURES High slew rate: 9 V/µs Wide bandwidth: 4 MHz Low supply current: 2 µa/amplifier max Low offset voltage: 3 mv max Low bias
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
More informationGeneral-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents: 4 pa Unity gain
More informationGeneral-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers AD854/AD8542/AD8544 FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents:
More informationDual Low Offset, Low Power Operational Amplifier OP200
Dual Low Offset, Low Power Operational Amplifier OP200 FEATURES Low input offset voltage: 75 μv maximum Low offset voltage drift, over 55 C < TA < +25 C 0.5 μv/ C maximum Low supply current (per amplifier):
More informationUltraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 25 C, 25 μv maximum Outstanding offset voltage drift 0. μv/ C maximum Excellent open-loop gain and gain linearity 2 V/μV typical
More informationUltralow Offset Voltage Operational Amplifier OP07
Ultralow Offset Voltage Operational Amplifier OP07 FEATURES Low VOS: 75 μv maximum Low VOS drift:.3 μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise: 0.6 μv p-p maximum Wide input voltage
More informationDual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP
Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One
More information10-Channel Gamma Buffer with VCOM Driver ADD8710
1-Channel Gamma Buffer with VCOM Driver ADD871 FEATURES Single-supply operation: 4.5 V to 18 V Upper/lower buffers swing to VS/GND Gamma continuous output current: >1 ma VCOM peak output current: 25 ma
More information1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier AD8515
Data Sheet FEATURES Single-supply operation: 1.8 V to 5 V Offset voltage: 6 mv maximum Space-saving SOT-23 and SC7 packages Slew rate: 2.7 V/μs Bandwidth: 5 MHz Rail-to-rail input and output swing Low
More informationZero Drift, Unidirectional Current Shunt Monitor AD8219
Zero Drift, Unidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to +85 V survival Buffered output voltage Gain = 6 V/V Wide operating temperature range:
More informationVery Low Distortion, Precision Difference Amplifier AD8274
Very Low Distortion, Precision Difference Amplifier AD8274 FEATURES Very low distortion.2% THD + N (2 khz).% THD + N ( khz) Drives Ω loads Excellent gain accuracy.3% maximum gain error 2 ppm/ C maximum
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628 FEATURES FUNCTIONAL BLOCK DIAGRAM High common-mode input voltage range ±20 V at VS = ±5 V Gain range 0. to 00 Operating temperature
More informationPrecision, Very Low Noise, Low Input Bias Current Operational Amplifiers
Data Sheet Precision, Very Low Noise, Low Input Bias Current Operational Amplifiers AD8671/AD8672/AD8674 FEATURES Very low noise: 2.8 nv/ Hz, 77 nv p-p Wide bandwidth: 1 MHz Low input bias current: 12
More information1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-1/ADA4051-2
.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA-/ADA-2 FEATURES Very low supply current: 3 μa typical Low offset voltage: μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8
More informationAD8603/AD8607/AD8609. Precision Micropower, Low Noise CMOS Rail-to-Rail Input/Output Operational Amplifiers
Precision Micropower, Low Noise CMOS Rail-to-Rail Input/Output Operational Amplifiers FEATURES Low offset voltage: μv max Low input bias current: 1 pa max Single-supply operation: 1.8 V to 5 V Low noise:
More informationLow Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2 AD8278/AD8279
Low Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2 /AD8279 FEATURES Wide input range beyond supplies Rugged input overvoltage protection Low supply current: 2 μa maximum (per amplifier)
More informationUltralow Power, Rail-to-Rail Output Operational Amplifiers OP281/OP481
Ultralow Power, Rail-to-Rail Output Operational Amplifiers OP28/OP48 FEATURES Low supply current: 4 μa/amplifier maximum Single-supply operation: 2.7 V to 2 V Wide input voltage range Rail-to-rail output
More informationRail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
More informationDual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature
Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by
More informationVery Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION
Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8273 FEATURES ±4 V HBM ESD Very low distortion.25% THD + N (2 khz).15% THD + N (1 khz) Drives 6 Ω loads Two gain settings Gain of
More informationLow Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS
More informationUltralow Offset Voltage Operational Amplifier OP07
FEATURES Low VOS: 5 μv maximum Low VOS drift:. μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise:. μv p-p maximum Wide input voltage range: ± V typical Wide supply voltage range: ± V
More informationHigh Voltage, Current Shunt Monitor AD8215
High Voltage, Current Shunt Monitor AD825 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead
More informationAD8218 REVISION HISTORY
Zero Drift, Bidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to 85 V survival Buffered output voltage Gain = 2 V/V Wide operating temperature range:
More informationQuad Low Offset, Low Power Operational Amplifier OP400
Quad Low Offset, Low Power Operational Amplifier OP4 FEATURES Low input offset voltage 5 μv max Low offset voltage drift over 55 C to 25 C,.2 pv/ C max Low supply current (per amplifier) 725 μa max High
More informationQuad Low Offset, Low Power Operational Amplifier OP400
FEATURES Low input offset voltage: 5 µv maximum Low offset voltage drift over 55 C to 25 C:.2 μv/ C maximum Low supply current (per amplifier): 725 µa maximum High open-loop gain: 5 V/mV minimum Input
More informationUltralow Offset Voltage Dual Op Amp AD708
Ultralow Offset Voltage Dual Op Amp FEATURES Very high dc precision 30 μv maximum offset voltage 0.3 μv/ C maximum offset voltage drift 0.35 μv p-p maximum voltage noise (0. Hz to 0 Hz) 5 million V/V minimum
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationHigh Voltage, Current Shunt Monitor AD8215
FEATURES ±4 V human body model (HBM) ESD High common-mode voltage range V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead SOIC: 4 C to + C Excellent
More informationHigh Resolution, Zero-Drift Current Shunt Monitor AD8217
High Resolution, Zero-Drift Current Shunt Monitor AD8217 FEATURES High common-mode voltage range 4.5 V to 8 V operating V to 85 V survival Buffered output voltage Wide operating temperature range: 4 C
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More informationADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
More informationZero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP OP FUNCTIONAL BLOCK DIAGRAM FEATURES ENHANCED PRODUCT FEATURES
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP FEATURES Digitally/pin-programmable gain G = 1, 2, 4, 8, 16, 32, 64, or 128 Specified from 55 C to +125 C 5 nv/ C maximum input offset
More informationQuad 7 ns Single Supply Comparator AD8564
Quad 7 ns Single Supply Comparator AD8564 FEATURES 5 V single-supply operation 7 ns propagation delay Low power Separate input and output sections TTL/CMOS logic-compatible outputs Wide output swing TSSOP,
More informationPrecision Micropower Single Supply Operational Amplifier OP777
a FEATURES Low Offset Voltage: 1 V Max Low Input Bias Current: 1 na Max Single-Supply Operation: 2.7 V to 3 V Dual-Supply Operation: 1.35 V to 15 V Low Supply Current: 27 A/Amp Unity Gain Stable No Phase
More informationUltraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 5 C, 5 μv maximum Outstanding offset voltage drift. μv/ C maximum Excellent open-loop gain and gain linearity V/μV typical CMRR:
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationSingle-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More informationAD8628/AD8629/AD863 TABLE OF CONTENTS Features... Applications... General Description... Pin Configurations... Revision History... 2 Specifications...
FEATURES Lowest auto-zero amplifier noise Low offset voltage: μv Input offset drift:.2 μv/ C Rail-to-rail input and output swing 5 V single-supply operation High gain, CMRR, and PSRR: 3 db Very low input
More information16 V Auto-Zero, Rail-to-Rail Output Operational Amplifiers AD8638/AD8639
6 V Auto-Zero, Rail-to-Rail Output Operational Amplifiers AD8638/AD8639 FEATURES Low offset voltage: 9 µv maximum Offset drift:.4 µv/ C maximum Rail-to-rail output swing 5 V to 6 V single-supply or ±2.5
More informationDual, High Voltage Current Shunt Monitor AD8213
Dual, High Voltage Current Shunt Monitor AD823 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range
More informationZero-Drift, High Voltage, Bidirectional Difference Amplifier AD8207
Zero-Drift, High Voltage, Bidirectional Difference Amplifier FEATURES Ideal for current shunt applications EMI filters included μv/ C maximum input offset drift High common-mode voltage range 4 V to +65
More informationPrecision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627
Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627 FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output
More informationLow Cost, High Speed Differential Amplifier AD8132
Low Cost, High Speed Differential Amplifier FEATURES High speed 350 MHz, 3 db bandwidth 1200 V/μs slew rate Resistor set gain Internal common-mode feedback Improved gain and phase balance 68 db @ 10 MHz
More informationPrecision, Low Power, Micropower Dual Operational Amplifier OP290
Precision, Low Power, Micropower Dual Operational Amplifier OP9 FEATURES Single-/dual-supply operation:. V to 3 V, ±.8 V to ±8 V True single-supply operation; input and output voltage Input/output ranges
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V
More informationDual Low Power Operational Amplifier, Single or Dual Supply OP221
a FEATURES Excellent TCV OS Match, 2 V/ C Max Low Input Offset Voltage, 15 V Max Low Supply Current, 55 A Max Single Supply Operation, 5 V to 3 V Low Input Offset Voltage Drift,.75 V/ C High Open-Loop
More informationHigh Voltage, Bidirectional Current Shunt Monitor AD8210
High Voltage, Bidirectional Current Shunt Monitor FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 5 V to +68 V survival Buffered output voltage 5 ma output drive capability
More informationSGM8551XN Single-Supply, Single Rail-to-Rail I/O Precision Operational Amplifier
PRODUCT DESCRIPTION The SGM8551XN is a single rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to
More informationSingle-Supply, 42 V System Difference Amplifier AD8206
Single-Supply, 42 V System Difference Amplifier FEATURES Ideal for current shunt applications High common-mode voltage range 2 V to +65 V operating 25 V to +75 V survival Gain = 20 Wide operating temperature
More informationAD8601/AD8602/AD8604. Precision CMOS, Single-Supply, Rail-to-Rail, Input/Output Wideband Operational Amplifiers FEATURES PIN CONFIGURATIONS
Precision CMOS, Single-Supply, Rail-to-Rail, Input/Output Wideband Operational Amplifiers FEATURES Low offset voltage: 5 μv maximum Single-supply operation: 2.7 V to 5.5 V Low supply current: 75 μa/amplifier
More informationAD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES
Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable
More informationPrecision Low Power Single-Supply JFET Amplifier AD8627/AD8626/AD8625
Precision Low Power Single-Supply JFET Amplifier FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Low supply current:
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
More informationPrecision, 16 MHz CBFET Op Amp AD845
a FEATURES Replaces Hybrid Amplifiers in Many Applications AC PERFORMANCE: Settles to 0.01% in 350 ns 100 V/ s Slew Rate 12.8 MHz Min Unity Gain Bandwidth 1.75 MHz Full Power Bandwidth at 20 V p-p DC PERFORMANCE:
More information6 db Differential Line Receiver
a FEATURES High Common-Mode Rejection DC: 9 db typ Hz: 9 db typ khz: 8 db typ Ultralow THD:.% typ @ khz Fast Slew Rate: V/ s typ Wide Bandwidth: 7 MHz typ (G = /) Two Gain Levels Available: G = / or Low
More information30 V, High Speed, Low Noise, Low Bias Current, JFET Operational Amplifier ADA4627-1/ADA4637-1
3 V, High Speed, Low Noise, Low Bias Current, JFET Operational Amplifier /ADA4637- FEATURES Low offset voltage: 2 µv maximum Offset drift: µv/ C typical Very low input bias current: 5 pa maximum Extended
More informationSingle-Supply, Low Cost Instrumentation Amplifier AD8223
Single-Supply, Low Cost Instrumentation Amplifier FEATURES Gain set with resistor Gain = 5 to Inputs Voltage range to 5 mv below negative rail 5 na maximum input bias current 3 nv/ Hz, RTI noise @ khz
More informationLow Cost, High Speed, Rail-to-Rail, Output Op Amps ADA4851-1/ADA4851-2/ADA4851-4
Low Cost, High Speed, Rail-to-Rail, Output Op Amps ADA485-/ADA485-/ADA485-4 FEATURES High speed 3 MHz, 3 db bandwidth 375 V/μs slew rate 55 ns settling time to.% Excellent video specifications. db flatness:
More informationHigh Voltage Current Shunt Monitor AD8211
High Voltage Current Shunt Monitor AD8211 FEATURES Qualified for automotive applications ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage
More informationHigh Voltage, Bidirectional Current Shunt Monitor AD8210
FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 5 V to +68 V survival Buffered output voltage 5 ma output drive capability Wide operating temperature range: 4 C to +125 C Ratiometric
More informationSGM8584 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier
PRODUCT DESCRIPTION The SGM8584 is a quad rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to 5.5V
More informationUltralow Input Bias Current Operational Amplifier AD549
Ultralow Input Bias Current Operational Amplifier AD59 FEATURES Ultralow input bias current 60 fa maximum (AD59L) 250 fa maximum (AD59J) Input bias current guaranteed over the common-mode voltage range
More informationLow Voltage Micropower Quad Operational Amplifier OP490
Low Voltage Micropower Quad Operational Amplifier FEATURES Single/dual-supply operation.6 V to 36 V ±0.8 V to ±8 V Single-supply operation; input and output voltage ranges include ground Low supply current:
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD8 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V to
More informationSelf-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
More informationPrecision Instrumentation Amplifier AD524
Precision Instrumentation Amplifier AD54 FEATURES Low noise: 0.3 μv p-p at 0. Hz to 0 Hz Low nonlinearity: 0.003% (G = ) High CMRR: 0 db (G = 000) Low offset voltage: 50 μv Low offset voltage drift: 0.5
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier FEATURES High common-mode input voltage range ±2 V at VS = ± V Gain range. to Operating temperature range: 4 C to ±8 C Supply voltage range
More informationSGM8554 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier
PRODUCT DESCRIPTION The SGM8554 is a quad rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to 5.5V
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
More informationAD8510/AD8512/AD8513. Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers FEATURES PIN CONFIGURATIONS
Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD5/AD5/AD5 FEATURES Fast settling time: 5 ns to.% Low offset voltage: μv maximum Low TCVOS: μv/ C typical
More informationTABLE OF CONTENTS AD8625/AD8626/AD8627 Specifications... 3 Electrical Characteristics... 3 Electrical Characteristics... 4 Absolute Maximum Ratings...
Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627 FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output
More informationImproved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
More informationPrecision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627
Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627 FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output
More informationDual Low Bias Current Precision Operational Amplifier OP297
Dual Low Bias Current Precision Operational Amplifier FEATURES Low offset voltage: μv maximum Low offset voltage drift:. μv/ C maximum Very low bias current: pa maximum Very high open-loop gain: 2 V/mV
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V
More information1.8 V to 5 V Auto-Zero, In-Amp with Shutdown AD8553
.8 V to 5 V Auto-Zero, In-Amp with Shutdown FEATURES Low offset voltage: 20 μv max Low input offset drift: 0. μv/ C max High CMR: 20 db min @ G = 00 Low noise: 0.7 μv p-p from 0.0 Hz to 0 Hz Wide gain
More informationSingle-Supply 42 V System Difference Amplifier AD8205
Single-Supply 42 V System Difference Amplifier FEATURES Ideal for current shunt applications High common-mode voltage range 2 V to +65 V operating 5 V to +68 V survival Gain = 50 Wide operating temperature
More information