TABLE OF CONTENTS AD8625/AD8626/AD8627 Specifications... 3 Electrical Characteristics... 3 Electrical Characteristics... 4 Absolute Maximum Ratings...
|
|
- Noreen Ryan
- 5 years ago
- Views:
Transcription
1 Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627 FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Low supply current: 63 µa/amp typ Low offset voltage: 5 µv max Unity gain stable No phase reversal APPLICATIONS Photodiode amplifiers ATEs Line-powered/battery-powered instrumentation Industrial controls Automotive sensors Precision filters Audio NC 8-Lead SOIC (R-8 Suffix) IN 2 7 V+ AD8627 +IN 3 6 OUT OUT A V 4 5 NC IN A +IN A NC = NO CONNECT Lead SOIC (R-8 Suffix) AD8626 PIN CONFIGURATIONS 8 NC V+ OUT B IN B V 4 5 +IN B 4-Lead SOIC (R-Suffix) OUT A V +IN OUT A IN A +IN A V Lead SC7 (KS Suffix) AD Lead MSOP (RM-Suffix) 4 AD Lead TSSOP (RU-Suffix) 5 4 V+ IN V+ OUT B IN B +IN B OUT A 4 OUT D OUT A 4 OUT D GENERAL DESCRIPTION IN A IN D IN A 2 3 IN D +IN A +IN D +IN A 3 2 +IN D V+ The AD862x is a precision JFET input amplifier. It features AD8625 V AD8625 +IN B +IN C V+ 4 V true single-supply operation, low power consumption, and IN B IN C +IN B 5 +IN C OUT B 7 8 OUT C rail-to-rail output. The outputs remain stable with capacitive IN B 6 9 IN C loads of over 5 pf; the supply current is less than 63 µa/amp. OUT B 7 8 OUT C Applications for the AD862x include photodiode transimpedance amplification, ATE reference level drivers, battery management, Figure. both line powered and portable instrumentation, and remote sensor signal conditioning, which includes automotive sensors. The AD862x s ability to swing nearly rail-to-rail at the input and rail-to-rail at the output enables it to be used to buffer CMOS DACs, ASICs, and other wide output swing devices in single-supply systems. The 5 MHz bandwidth and low offset are ideal for precision filters. The AD862x is fully specified over the industrial temperature range. ( 4 C to +85 C). The AD8627 is available in both 5-lead SC7 and 8-lead SOIC surface-mount packages (SC7 packaged parts are available in tape and reel only). The AD8626 is available in MSOP and SOIC packages, while the AD8625 is available in TSSOP and SOIC packages Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 96, Norwood, MA , U.S.A. Tel: Fax: Analog Devices, Inc. All rights reserved.
2 TABLE OF CONTENTS AD8625/AD8626/AD8627 Specifications... 3 Electrical Characteristics... 3 Electrical Characteristics... 4 Absolute Maximum Ratings... 5 Typical Performance Characteristics... 6 Applications... 3 Minimizing Input Current... 5 Photodiode Preamplifier Application... 5 Output Amplifier for DACs... 6 Eight-Pole Sallen Key Low-Pass Filter... 7 Outline Dimensions... 8 Ordering Guide... 9 REVISION HISTORY /4 Data Sheet Changed from Rev. B to Rev. C /3 Data Sheet Changed from Rev. to Rev. A Updated Figure Codes...Universal Changes to Figure 7 and Changes to Figure 33 and Figure Changes to Figure Changes to Figure 39 and Figure Changes to Figure 4 to Figure Addition of two new parts Universal Change to General Description. Changes to Pin Configurations... Change to Specifications table 3 Changes to Figure 3... Changes to Figure Changes to Figure Changes to Figure Changes to Figure Changes to Figure /4 Data Sheet Changed from Rev. A to Rev. B Change to General Description... Change to Figure... 7 Updated Outline Dimensions... 8 Change to Figure Changes to Ordering Guide... 9 Change to Figure Changes to Figure Change to Output Amplifier for DACs section... 5 Updated Outline Dimensions... 9 Rev. C Page 2 of 2
3 AD8625/AD8626/AD8627 SPECIFICATIONS ELECTRICAL = 5 V, VCM =.5 V, TA = 25 C, unless otherwise noted. Table. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS.5.5 mv 4 C < TA < +85 C.2 mv Input Bias Current IB.25 pa 4 C < TA < +85 C 6 pa Input Offset Current IOS.5 pa 4 C < TA < +85 C 25 pa Input Voltage Range 3 V Common-Mode Rejection Ratio CMRR VCM = V to 2.5 V db Large Signal Voltage Gain AVO RL = kω, VO =.5 V to 4.5 V 23 V/mV Offset Voltage Drift VOS/ T 4 C < TA < +85 C 2.5 µv/ C OUTPUT CHARACTERISTICS Output Voltage High VOH 4.92 V IL = 2 ma, 4 C < TA < +85 C 4.9 V Output Voltage Low VOL.75 V IL = 2 ma, 4 C < TA < +85 C.8 V Output Current IOUT ± ma POWER SUPPLY Power-Supply Rejection Ratio PSRR VS = 5 V to 26 V 8 4 db Supply Current/Amplifier ISY µa 4 C < TA < +85 C 8 µa DYNAMIC PERFORMANCE Slew Rate SR 5 V/µs Gain Bandwidth Product GBP 5 MHz Phase Margin ØM 6 Degrees NOISE PERFORMANCE Voltage Noise en p-p. Hz to Hz.9 µv p-p Voltage Noise Density en f = khz 7.5 nv/ Hz Current Noise Density in f = khz.4 fa/ Hz Channel Separation Cs f = khz 4 db Rev. C Page 3 of 2
4 ELECTRICAL = ±3 V; VCM = V; TA = 25 C, unless otherwise noted. Table 2. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS mv 4 C < TA < +85 C.35 mv Input Bias Current IB.25 pa 4 C < TA < +85 C 6 pa Input Offset Current IOS.5 pa 4 C < TA < +85 C 25 pa Input Voltage Range 3 + V Common-Mode Rejection Ratio CMRR VCM = 3 V to + V 76 5 db Large Signal Voltage Gain AVO RL = kω, VO = V to + V 5 3 V/mV Offset Voltage Drift VOS/ T 4 C < TA < +85 C 2.5 µv/ C OUTPUT CHARACTERISTICS Output Voltage High VOH V VOH IL = 2 ma, 4 C < TA < +85 C +2.9 V Output Voltage Low VOL 2.92 V VOL IL = 2 ma, 4 C < TA < +85 C 2.9 V Output Current IOUT ±5 ma POWER SUPPLY Power-Supply Rejection Ratio PSRR VS = ±2.5 V to ±3 V 8 4 db Supply Current/Amplifier ISY 7 85 µa 4 C < TA < +85 C 9 µa DYNAMIC PERFORMANCE Slew Rate SR 5 V/µs Gain Bandwidth Product GBP 5 MHz Phase Margin ØM 6 Degrees NOISE PERFORMANCE Voltage Noise en p-p. Hz to Hz 2.5 µv p-p Voltage Noise Density en f = khz 6 nv/ Hz Current Noise Density in f = khz.5 fa/ Hz Channel Separation Cs f = khz 5 db Rev. C Page 4 of 2
5 ABSOLUTE MAXIMUM RATINGS Absolute maximum ratings apply at 25 C, unless otherwise noted. Table 3. Stress Ratings Parameter Ratings Supply Voltage 27 V Input Voltage VS to VS+ Differential Input Voltage ± Supply Voltage Output Short-Circuit Duration Indefinite Storage Temperature Range, R Package 65 C to +25 C Operating Temperature Range 4 C to +85 C Junction Temperature Range, R Package 65 C to +5 C Lead Temperature Range (Soldering, 6 sec) 3 C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 4. Package Type θja θjc Unit 5-Lead SC7 (KS) C/W 8-Lead MSOP (RM) 2 45 C/W 8-Lead SOIC (R) C/W 4-Lead SOIC (R) 2 36 C/W 4-Lead TSSOP (RU) 8 35 C/W θja is specified for worst-case conditions when devices are soldered in circuit boards for surface-mount packages. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. C Page 5 of 2
6 TYPICAL PERFORMANCE CHARACTERISTICS NUMBER OF AMPLIFIERS V SY = ±2V T A = 25 C VOLTAGE (µv) Figure 2. Input Offset Voltage NUMBER OF AMPLIFIERS 6 V SY = +3.5V/.5V OFFSET VOLTAGE (µv/ C) Figure 5. Offset Voltage Drift NUMBER OF AMPLIFIERS T A = 25 C OFFSET VOLTAGE (µv/ C) V CM (V) INPUT BIAS CURRENT (pa) Figure 3. Offset Voltage Drift Figure 6. Input Bias Current vs. VCM 8 6 V SY = +3.5V/.5V. T A = 25 C NUMBER OF AMPLIFIERS INPUT BIAS CURRENT (pa) VOLTAGE (µv) V CM (V) Figure 4. Input Offset Voltage Figure 7. Input Bias Current vs. VCM Rev. C Page 6 of 2
7 V CM = V 5 4 V SY = 5V INPUT BIAS CURRENT (pa) INPUT OFFSET VOLTAGE (µv) TEMPERATURE ( C) Figure 8. Input Bias Current vs. Temperature V CM (V) Figure. Input Offset Voltage vs. VCM V SY = +5V OR ±5V M INPUT BIAS CURRENT (pa)..5 V SY = +5V.5 k V CM (V) OPEN-LOOP GAIN (V/V) M k. LOAD RESISTANCE (kω) Figure 9. Input Bias Current vs. VCM Figure 2. Open-Loop Gain vs. Load Resistance 9 a INPUT OFFSET VOLTAGE (µv) V CM (V) Figure. Input Offset Voltage vs. VCM 323- OPEN-LOOP GAIN (V/mV) d b c e a., V O = ±V, R L = kω b., V O = ±V, R L = 2kΩ c. V SY = +5V, V O = +.5V/+4.5V, R L = 2kΩ d. V SY = +5V, V O = +.5V/+4.5V, R L = kω e. V SY = +5V, V O = +.5V/+4.5V, R L = 6Ω TEMPERATURE ( C) Figure 3. Open-Loop Gain vs. Temperature Rev. C Page 7 of 2
8 6 5 k OFFSET VOLTAGE (µv) R L = kω R L = 6Ω R L = kω V SY OUTPUT VOLTAGE (mv) k V OL V OH OUTPUT VOLTAGE (V) Figure 4. Input Error Voltage vs. Output Voltage for Resistive Loads LOAD CURRENT (ma) Figure 7. Output Saturation Voltage vs. Load Current INPUT VOLTAGE (µv) k R L = kω V SY = ±5V V SY = 5V POS RAIL R L = kω R L = kω R L = kω R L = kω V OL NEG RAIL V OH OUTPUT VOLTAGE FROM SUPPLY RAILS (mv) V SY OUTPUT VOLTAGE (mv) k... LOAD CURRENT (ma) Figure 5. Input Error Voltage vs. Output Voltage within 3 mv of Supply Rails Figure 8. Output Saturation Voltage vs. Load Current QUIESCENT CURRENT (µa) C 6 55 C +25 C TOTAL SUPPLY VOLTAGE (V) GAIN (db) GAIN R L = 2kΩ C L = 4pF PHASE 3 35 k k M M 5M PHASE (Degrees) Figure 6. Quiescent Current vs. Supply Voltage at Different Temperatures Figure 9. Open-Loop Gain and Phase Margin vs. Frequency Rev. C Page 8 of 2
9 7 6 5 V SY = 5V R L = 2kΩ C L = 4pF GAIN (db) GAIN PHASE PHASE (Degrees) CMRR (db) k k M M 5M Figure 2. Open-Loop Gain and Phase Margin vs. Frequency k k k M M Figure 23. CMRR vs. Frequency R L = 2kΩ C L = 4pF 4 2 V SY =5V GAIN (db) 4 G = G = + 2 G = k k k M M 5M CMRR (db) k k k M M Figure 2. Closed-Loop Gain vs. Frequency Figure 24. CMRR vs. Frequency V SY = 5V R L = 2kΩ C L = 4pF 4 2 GAIN (db) G = + G = + PSRR (db) PSRR +PSRR G = k k k M M 5M Figure 22. Closed-Loop Gain vs. Frequency k k k M M Figure 25. PSRR vs. Frequency Rev. C Page 9 of 2
10 4 2 V SY =5V INPUT PSRR (db) PSRR +PSRR VOLTAGE (V/DIV) OUTPUT k k k M M TIME (4µs/DIV) Figure 26. PSRR vs. Frequency Figure 29. No Phase Reversal Z OUT (Ω) TS (.%) 5 G = + G = + TS (%) G = + k k k M M M OUTPUT SWING (V) 5 5 TS + (%) TS + (.%) SETTLING TIME (µs) Figure 27. Output Impedance vs. Frequency Figure 3. Output Swing and Error vs. Settling Time Z OUT (Ω) 3 V SY =5V G = + G = + 6 G = + 3 k k k M M M Figure 28. Output Impedance vs. Frequency OVERSHOOT (%) V S = ±3V R L = kω V IN = mv p-p A V = + OS OS+ k CAPACITANCE (pf) Figure 3. Small-Signal Overshoot vs. Load Capacitance Rev. C Page of 2
11 OVERSHOOT (%) V S = ±2.5V R L = kω V IN = mv p-p A V = + OS+ OS k CAPACITANCE (pf) Figure 32. Small-Signal Overshoot vs. Load Capacitance VOLTAGE (nv) nV/ Hz FREQUENCY (khz) Figure 35. Voltage Noise Density A VO =,V/V V SY = 5V VOLTAGE (5mV/DIV) TIME (s/div) VOLTAGE (nv) nV/ Hz FREQUENCY (khz) Figure 33.. Hz to Hz Noise Figure 36. Voltage Noise Density V SY = ±2.5V A VO =,V/V 4 5 VOLTAGE (5mV/DIV) THD + NOISE (db) V SY = ±5V, V IN = 9V p-p, V IN = 8V p-p TIME (s/div) Figure 34.. Hz to Hz Noise V SY = ±2.5V, V IN = 4.5V p-p k k k Figure 37. Total Harmonic Distortion + Noise vs. Frequency Rev. C Page of 2
12 AD8625/AD8626/AD8627 2kΩ 2kΩ V IN 2kΩ 2kΩ 8 9 CHANNEL SEPARATION (db) V IN = 9V p-p V IN = 4.5V p-p V IN = 8V p-p 5 6 k k k Figure 38. Channel Separation Rev. C Page 2 of 2
13 APPLICATIONS The AD862x is one of the smallest and most economical JFETs offered. It has true single-supply capability and has an input voltage range that extends below the negative rail, allowing the part to accommodate input signals below ground. The rail-to-rail output of the AD862x provides the maximum dynamic range in many applications. To provide a low offset, low noise, high impedance input stage, the AD862x uses n-channel JFETs. The input common-mode voltage extends from.2 V below VS to 2 V below +VS. Driving the input of the amplifier, configured in the unity gain buffer, closer than 2 V to the positive rail causes an increase in common-mode voltage error, as illustrated in Figure 5, and a loss of amplifier bandwidth. This loss of bandwidth causes the rounding of the output waveforms shown in Figure 39 and Figure 4, which have inputs that are V and V from +VS, respectively. VOLTAGE (2V/DIV) V SY = 5V INPUT 4V V 4V OUTPUT V TIME (2µs/DIV) Figure 39. Unity Gain Follower Response to V to 4 V Step The AD862x does not experience phase reversal with input signals close to the positive rail, as shown in Figure 29. For V SY = 5V 5V input voltages greater than +VSY, a resistor in series with the INPUT AD862x s noninverting input prevents phase reversal at the expense of greater input voltage noise. This current-limiting resistor should also be used if there is a possibility of the input V voltage exceeding the positive supply by more than 3 mv, or if an input voltage is applied to the AD862x when ±VSY =. 4V Either of these conditions damages the amplifier if the OUTPUT condition exists for more than seconds. A kω resistor allows the amplifier to withstand up to V of continuous V overvoltage, while increasing the input voltage noise by a negligible amount. VOLTAGE (2V/DIV) TIME (2µs/DIV) Figure 4. Unity Gain Follower Response to V to 5 V Step Rev. C Page 3 of 2
14 The AD862x can safely withstand input voltages 5 V below VSY if the total voltage between the positive supply and the input terminal is less than 26 V. Figure 4 through Figure 43 show the AD862x in different configurations accommodating signals close to the negative rail. The amplifier input stage typically maintains picoamp-level input currents across that input voltage range. kω V mv 3mV 2kΩ +5V V SY = 5V 2kΩ V SY = 5V, V V kω 2.5V +5V VOLTAGE (mv/div) VOLTAGE (V/DIV) 5V V TIME (2µs/DIV) Figure 43. Gain-of-Two Inverter Response to 2 mv Step, Centered 2 mv below Ground V TIME (2µs/DIV) AD862x contributes negligible noise for applications with large Figure 4. Gain-of-Two Inverter Response to 2.5 V Step, Centered.25 V below Ground source resistances. 6mV 2mV V 5V 6Ω The AD862x is designed for 6 nv/ Hz wideband input voltage noise and maintains low noise performance to low frequencies, as shown in Figure 35. This noise performance, along with the AD862x s low input current and current noise, means that the The AD862x has a unique bipolar rail-to-rail output stage that swings within 5 mv of the rail when up to 2 ma of current is drawn. At larger loads, the drop-out voltage increases, as shown in Figure 7 and Figure 8. The AD862x s wide bandwidth and fast slew rate allows it to be used with faster signals than older single-supply JFETs. Figure 44 shows the response of the AD862x, configured in unity gain, to a VIN of 2 V p-p at 5 khz. The full-power bandwidth (FPBW) of the part is close to khz. R L = 6Ω VOLTAGE (mv/div) VOLTAGE (5V/DIV) V V V SY = 5V R L = 6Ω TIME (2µs/DIV) Figure 42. Unity Gain Follower Response to 4 mv Step, Centered 4 mv above Ground TIME (5µs/DIV) Figure 44. Unity Gain Follower Response to 2 V, 5 khz Input Signal Rev. C Page 4 of 2
15 The AD862x is guaranteed to pa maximum input current with a ±3 V supply voltage at room temperature. Careful attention to how the amplifier is used maintains or possibly betters this performance. The amplifier s operating temperature should be kept as low as possible. Like other JFET input amplifiers, the AD862x s input current doubles for every C rise in junction temperature, as illustrated in Figure 8. On-chip power dissipation raises the device operating temperature, causing an increase in input current. Reducing supply voltage to cut power dissipation reduces the AD862x s input current. Heavy output loads can also increase chip temperature; maintaining a minimum load resistance of kω is recommended. AD8625/AD8626/AD8627 MINIMIZING INPUT CURRENT The amplifier s input current, IB, contributes an output voltage error proportional to the value of the feedback resistor. The offset voltage error, VOS, causes a small current error due to the photodiode s finite shunt resistance, RD. The AD862x is designed for mounting on PC boards. Maintaining picoampere resolution in those environments requires a lot of care. Both the board and the amplifier s package have finite resistance. Voltage differences between the input pins and other pins, as well as PC board metal traces may cause parasitic currents larger than the AD862x s input current, unless special C F precautions are taken. To ensure the best result, refer to the ADI 5pF website for proper board layout seminar materials. Two common methods of minimizing parasitic leakages that should R F PHOTODIODE.5MΩ V be used are guarding of the input lines and maintaining OS OUTPUT adequate insulation resistance. R D I C4 B I 5pF B MΩ AD8627 Contaminants, such as solder flux on the board s surface and the amplifier s package, can greatly reduce the insulation resistance between the input pin and traces with supply or signal voltages. Both the package and the board must be kept clean and dry. PHOTODIODE PREAMPLIFIER APPLICATION The low input current and offset voltage levels of the AD862x, together with its low voltage noise, make this amplifier an excellent choice for preamplifiers used in sensitive photodiode applications. In a typical photovoltaic preamp circuit, shown in Figure 45, the output of the amplifier is equal to The resulting output voltage error, VE, is equal to R f VE = + VOS + R D R (I f B A shunt resistance on the order of MΩ is typical for a small photodiode. Resistance RD is a junction resistance that typically drops by a factor of two for every C rise in temperature. In the AD862x, both the offset voltage and drift are low, which helps minimize these errors. With IB values of pa and VOS of 5 mv, VE for Figure 45 is very negligible. Also, the circuit in Figure 45 results in an SNR value of 95 db for a signal bandwidth of 3 khz. Figure 45. A Photodiode Model Showing DC Error ) V OUT = ID(R ) = R (P)R f p f where: ID = photodiode signal current (A). Rp = photodiode sensitivity (A/W). Rf = value of the feedback resistor, in Ω. P = light power incident to photodiode surface, in W. Rev. C Page 5 of 2
16 OUTPUT AMPLIFIER FOR DACs Many system designers use amplifiers as buffers on the output of amplifiers to increase the DAC s output driving capability. The high resolution current output DACs need high precision amplifiers on their output as current-to-voltage converters (I/V). Additionally, many DACs operate with a single supply of 5 V. In a single-supply application, selection of a suitable op amp may be more difficult because the output swing of the amplifier does not usually include the negative rail, in this case AGND. This can result in some degradation of the DAC s specified performance, unless the application does not use codes near zero. The selected op amp needs to have very low offset voltage for a 4-bit DAC, the DAC LSB is 3 µv with a 5 V reference to eliminate the need for output offset trims. Input bias current should also be very low because the bias current multiplied by the DAC output impedance (about kω in some cases) adds to the zero-code error. Rail-to-rail input and output performance is desired. For fast settling, the slew rate of the op amp should not impede the settling time of the DAC. Output impedance of the DAC is constant and code independent, but in order to minimize gain errors, the input impedance of the output amplifier should be as high as possible. The AD862x, with a very high input impedance, IB of pa, and a fast slew rate, is an ideal amplifier for these types of applications. A typical configuration with a popular DAC is shown in Figure 46. In these situations, the amplifier adds another time constant to the system, increasing the settling time of the output. The AD862x, with 5 MHz of BW, helps in achieving a faster effective settling time of the combined DAC and amplifier. In applications with full 4-quadrant multiplying capability or a bipolar output swing, the circuit in Figure 47 can be used. In this circuit, the first and second amplifiers provide a total gain of 2, which increases the output voltage span to 2 V. Biasing the external amplifier with a V offset from the reference voltage results in a full 4-quadrant multiplying circuit. SERIAL INTERFACE V.µF *AD5552 ONLY VREF ADR 5V 2.5V.µF µf V DD V REFF * V REFS * CS DIN AD555/AD5552 SCLK LDAC* DGND AGND V DD V REF X R FB X OUT Figure 46. Unipolar Output 5V AD8627 UNIPOLAR OUTPUT ONE CHANNEL AD5544 /2 AD8626 V SS A GND F A GND X kω 5kΩ DIGITAL INTERFACE CONNECTIONS OMITTED FOR CLARITY kω +3V /2 AD8626 3V Figure Quadrant Multiplying Application Circuit V OUT V < V OUT < +V Rev. C Page 6 of 2
17 EIGHT-POLE SALLEN KEY LOW-PASS FILTER The AD862x s high input impedance and dc precision make it a great selection for active filters. Due to the very low bias current of the AD862x, high value resistors can be used to construct low frequency filters. The AD862x s picoamp-level input currents contribute minimal dc errors. Figure 49 shows an example of a Hz, 8-pole Sallen Key filter constructed using the AD862x. Different numbers of the AD862x can be used depending on the desired response, which is shown in Figure 48. The high value used for R minimizes interaction with signal source resistance. Pole placement in this version of the filter minimizes the Q associated with the lower pole section of the filter. This eliminates any peaking of the noise contribution of resistors in the preceding sections, minimizing the inherent output voltage noise of the filter. VOLTAGE (V) V4 V2 V V3 k Figure 48. Frequency Response Output at Different Stages of the Low-Pass Filter C µf R 62.3kΩ V3 R2 V DD V IN 62.3kΩ 3 4 U R C3 V 9.4kΩ µf D 2 /4 R5 C2 R AD kΩ 96.9µF U kΩ C5 V D EE V2 µf R3 25kΩ C4 69.4µF D /4 AD8625 R4 25kΩ C6 3.86µF R kΩ D R6 25kΩ U3 V3 /4 AD8625 R2 85.8kΩ C8 3.85µF R9 85.8kΩ D C7 µf U4 /4 AD8625 R8 25kΩ V Figure 49. Hz, 8-Pole Sallen Key Low-Pass Filter Rev. C Page 7 of 2
18 OUTLINE DIMENSIONS 2. BSC 8.75 (.3445) 8.55 (.3366).25 BSC BSC 4. (.575) 3.8 (.496) (.244) 5.8 (.2283) PIN MAX.3.5. COPLANARITY.65 BSC. MAX SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-23AA Figure 5. 5-Lead Plastic Surface-Mount Package [SC7] (KS-5) Dimensions shown in millimeters 4. (.574) 3.8 (.497) 5. (.968) 4.8 (.89) (.244) 5.8 (.2284) (.98). (.39) COPLANARITY..27 (.5) BSC.5 (.2).3 (.22).75 (.689).35 (.53) SEATING PLANE.25 (.98).7 (.67) COMPLIANT TO JEDEC STANDARDS MS-2AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 8.5 (.97) (.98).27 (.5).4 (.57) Figure Lead Standard Small Outline Package [SOIC] (R-4) Dimensions shown in millimeters and (inches) (.98). (.4) COPLANARITY BSC.27 (.5).5 (.96).25 (.99) BSC.75 (.688).35 (.532) 7 PIN.5 (.2) 8.25 (.98).27 (.5).5.65 SEATING.3 (.22).7 (.67).4 (.57). BSC PLANE.8 COMPLIANT TO JEDEC STANDARDS MS-2AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN MAX SEATING PLANE.2.9 COPLANARITY. 8 COMPLIANT TO JEDEC STANDARDS MO-53AB Figure 5. 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) Dimensions shown in millimeters and (inches) Figure Lead Thin Shrink Small Outline Package [TSSOP] (RU-4) Dimensions shown in millimeters 3. BSC 3. BSC BSC PIN.65 BSC COPLANARITY.. MAX SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-87AA Figure Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters Rev. C Page 8 of 2
19 ORDERING GUIDE Model Temperature Range Package Description Package Option Branding AD8627AKS-REEL 4 C to +85 C 5-Lead SC7 KS-5 B9A AD8627AKS-REEL7 4 C to +85 C 5-Lead SC7 KS-5 B9A AD8627AKS-R2 4 C to +85 C 5-Lead SC7 KS-5 B9A AD8627AKSZ-REEL 4 C to +85 C 5-Lead SC7 KS-5 B9A AD8627AKSZ-REEL7 4 C to +85 C 5-Lead SC7 KS-5 B9A AD8627AKSZ-R2 4 C to +85 C 5-Lead SC7 KS-5 B9A AD8627AR 4 C to +85 C 8-Lead SOIC R-8 AD8627AR-REEL 4 C to +85 C 8-Lead SOIC R-8 AD8627AR-REEL7 4 C to +85 C 8-Lead SOIC R-8 AD8627ARZ 4 C to +85 C 8-Lead SOIC R-8 AD8627ARZ-REEL 4 C to +85 C 8-Lead SOIC R-8 AD8627ARZ-REEL7 4 C to +85 C 8-Lead SOIC R-8 AD8626ARM-REEL 4 C to +85 C 8-Lead MSOP RM-8 BJA AD8626ARM-R2 4 C to +85 C 8-Lead MSOP RM-8 BJA AD8626ARMZ-REEL 4 C to +85 C 8-Lead MSOP RM-8 BJA AD8626ARMZ-R2 4 C to +85 C 8-Lead MSOP RM-8 BJA AD8626AR 4 C to +85 C 8-Lead SOIC R-8 AD8626AR-REEL 4 C to +85 C 8-Lead SOIC R-8 AD8626AR-REEL7 4 C to +85 C 8-Lead SOIC R-8 AD8626ARZ 4 C to +85 C 8-Lead SOIC R-8 AD8626ARZ-REEL 4 C to +85 C 8-Lead SOIC R-8 AD8626ARZ-REEL7 4 C to +85 C 8-Lead SOIC R-8 AD8625ARU 4 C to +85 C 4-Lead TSSOP RU-4 AD8625ARU-REEL 4 C to +85 C 4-Lead TSSOP RU-4 AD8625ARUZ 4 C to +85 C 4-Lead TSSOP RU-4 AD8625ARUZ-REEL 4 C to +85 C 4-Lead TSSOP RU-4 AD8625AR 4 C to +85 C 4-Lead SOIC R-4 AD8625AR-REEL 4 C to +85 C 4-Lead SOIC R-4 AD8625AR-REEL7 4 C to +85 C 4-Lead SOIC R-4 AD8625ARZ 4 C to +85 C 4-Lead SOIC R-4 AD8625ARZ-REEL 4 C to +85 C 4-Lead SOIC R-4 AD8625ARZ-REEL7 4 C to +85 C 4-Lead SOIC R-4 Z = Pb-free part. Rev. C Page 9 of 2
20 AD8625/AD8626/AD8627 NOTES 24 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C323--/4(C) Rev. C Page 2 of 2
Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627
Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627 FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output
More informationPrecision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627
Precision Low Power Single-Supply JFET Amplifiers AD8625/AD8626/AD8627 FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output
More informationPrecision Low Power Single-Supply JFET Amplifier AD8627/AD8626/AD8625
Precision Low Power Single-Supply JFET Amplifier FEATURES SC7 package Very low IB: pa max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Low supply current:
More informationAD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
More informationLow Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
More informationTABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum
FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input
More informationAD8613/AD8617/AD8619. Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers PIN CONFIGURATIONS FEATURES APPLICATIONS
Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers FEATURES Offset voltage: 2.2 mv maximum Low input bias current: pa maximum Single-supply operation:.8 V to 5 V Low
More information16 V, 4 MHz RR0 Amplifiers AD8665/AD8666/AD8668
6 V, MHz RR Amplifiers AD8665/AD8666/AD8668 FEATURES Offset voltage:.5 mv max Low input bias current: pa max Single-supply operation: 5 V to 6 V Dual-supply operation: ±.5 V to ±8 V Low noise: 8 nv/ Hz
More informationGeneral-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers AD854/AD8542/AD8544 FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents:
More informationLow Power, Precision, Auto-Zero Op Amps AD8538/AD8539 FEATURES Low offset voltage: 13 μv maximum Input offset drift: 0.03 μv/ C Single-supply operatio
Low Power, Precision, Auto-Zero Op Amps FEATURES Low offset voltage: 3 μv maximum Input offset drift:.3 μv/ C Single-supply operation: 2.7 V to 5.5 V High gain, CMRR, and PSRR Low input bias current: 25
More information24 MHz Rail-to-Rail Amplifiers with Shutdown Option AD8646/AD8647/AD8648
24 MHz Rail-to-Rail Amplifiers with Shutdown Option AD8646/AD8647/AD8648 FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew
More informationAD8603/AD8607/AD8609. Precision Micropower, Low Noise CMOS Rail-to-Rail Input/Output Operational Amplifiers
Precision Micropower, Low Noise CMOS Rail-to-Rail Input/Output Operational Amplifiers FEATURES Low offset voltage: μv max Low input bias current: 1 pa max Single-supply operation: 1.8 V to 5 V Low noise:
More informationPrecision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608
Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608 FEATURES Low offset voltage: 65 μv maximum Low input bias currents: pa maximum Low noise: 8 nv/ Hz Wide
More informationMicropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
More informationGeneral-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents: 4 pa Unity gain
More informationDual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
More informationLow Cost, Precision JFET Input Operational Amplifiers ADA4000-1/ADA4000-2/ADA4000-4
Low Cost, Precision JFET Input Operational Amplifiers ADA-/ADA-/ADA- FEATURES High slew rate: V/μs Fast settling time Low offset voltage:.7 mv maximum Bias current: pa maximum ± V to ±8 V operation Low
More informationDual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP22/OP42 FEATURES High slew rate: 9 V/µs Wide bandwidth: 4 MHz Low supply current: 2 µa/amplifier max Low offset voltage: 3 mv max Low bias
More information15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
More informationPrecision, Very Low Noise, Low Input Bias Current Operational Amplifiers
Data Sheet Precision, Very Low Noise, Low Input Bias Current Operational Amplifiers AD8671/AD8672/AD8674 FEATURES Very low noise: 2.8 nv/ Hz, 77 nv p-p Wide bandwidth: 1 MHz Low input bias current: 12
More informationUltraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
FEATURES Very low voltage noise 2.8 nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain:
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
More informationLow Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Preliminary Technical Data FEATURES TL082 / TL08 compatible Low input bias current: 0 pa max Offset voltage: 5mV max (ADTL082A/ADTL08A) 9 mv max (ADTL082/ADTL08) ±5 V to ±5 V operation Low noise: 5 nv/
More informationVery Low Distortion, Precision Difference Amplifier AD8274
Very Low Distortion, Precision Difference Amplifier AD8274 FEATURES Very low distortion.2% THD + N (2 khz).% THD + N ( khz) Drives Ω loads Excellent gain accuracy.3% maximum gain error 2 ppm/ C maximum
More informationUltraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
Ultraprecision, 36 V, 2. nv/ Hz Dual Rail-to-Rail Output Op Amp AD676 FEATURES Very low voltage noise: 2. nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage:
More informationLow Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Low Cost JFET Input Operational Amplifiers ADTL/ADTL FEATURES TL/TL compatible Low input bias current: pa maximum Offset voltage 5.5 mv maximum (ADTLA/ADTLA) 9 mv maximum (ADTLJ/ADTLJ) ±5 V operation Low
More information16 V, 1 MHz, CMOS Rail-to-Rail Input/Output Operational Amplifier ADA4665-2
6 V, MHz, CMOS Rail-to-Rail Input/Output Operational Amplifier ADA4665-2 FEATURES Lower power at high voltage: 29 μa per amplifier typical Low input bias current: pa maximum Wide bandwidth:.2 MHz typical
More informationSingle and Dual, Ultralow Distortion, Ultralow Noise Op Amps AD8597/AD8599 PIN CONFIGURATIONS FEATURES APPLICATIONS
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps FEATURES Low noise:. nv/ Hz at khz Low distortion: db THD @ khz Input noise,. Hz to Hz:
More informationSingle-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More information1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier AD8515
Data Sheet FEATURES Single-supply operation: 1.8 V to 5 V Offset voltage: 6 mv maximum Space-saving SOT-23 and SC7 packages Slew rate: 2.7 V/μs Bandwidth: 5 MHz Rail-to-rail input and output swing Low
More informationPrecision Micropower Single Supply Operational Amplifier OP777
a FEATURES Low Offset Voltage: 1 V Max Low Input Bias Current: 1 na Max Single-Supply Operation: 2.7 V to 3 V Dual-Supply Operation: 1.35 V to 15 V Low Supply Current: 27 A/Amp Unity Gain Stable No Phase
More informationDual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482 FEATURES High slew rate: 9 V/μs Wide bandwidth: 4 MHz Low supply current: 2 μa/amplifier maximum Low offset voltage: 3 mv maximum
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More information150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
More information4 MHz, 7 nv/ Hz, Low Offset and Drift, High Precision Amplifier ADA EP
Enhanced Product FEATURES Low offset voltage and low offset voltage drift Maximum offset voltage: 9 µv at TA = 2 C Maximum offset voltage drift:.2 µv/ C Moisture sensitivity level (MSL) rated Low input
More informationLow Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS
More information10-Channel Gamma Buffer with VCOM Driver ADD8710
1-Channel Gamma Buffer with VCOM Driver ADD871 FEATURES Single-supply operation: 4.5 V to 18 V Upper/lower buffers swing to VS/GND Gamma continuous output current: >1 ma VCOM peak output current: 25 ma
More information1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-2
.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA45-2 FEATURES Very low supply current: 3 μa Low offset voltage: 5 μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8 V
More informationUltraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 25 C, 25 μv maximum Outstanding offset voltage drift 0. μv/ C maximum Excellent open-loop gain and gain linearity 2 V/μV typical
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V
More informationPrecision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD8510/AD8512
a FEATURES Fast Settling Time: 5 ns to.1% Low Offset Voltage: V Max Low TcV OS : 1 V/ C Typ Low Input Bias Current: 25 pa Typ Dual-Supply Operation: 5 V to 15 V Low Noise: 8 nv/ Hz Low Distortion:.5% No
More informationDual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP
Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One
More informationAD8628/AD8629/AD863 TABLE OF CONTENTS Features... Applications... General Description... Pin Configurations... Revision History... 2 Specifications...
FEATURES Lowest auto-zero amplifier noise Low offset voltage: μv Input offset drift:.2 μv/ C Rail-to-rail input and output swing 5 V single-supply operation High gain, CMRR, and PSRR: 3 db Very low input
More informationPrecision CMOS Single-Supply Rail-to-Rail Input/Output Wideband Operational Amplifiers AD8601/AD8602/AD8604
Precision CMOS Single-Supply Rail-to-Rail Input/Output Wideband Operational Amplifiers AD86/AD862/AD864 FEATURES Low Offset Voltage: V Max Single-Supply Operation: 2.7 V to. V Low Supply Current: 7 A/Amplifier
More informationTABLE OF CONTENTS Features... Applications... General Description... Pin Configurations... Revision History... 2 Specifications... 3 Electrical Charac
6 V Rail-to-Rail Operational Amplifiers AD86/AD866/AD867 FEATURES Single-supply operation: 4. V to 6 V Input capability beyond the rails Rail-to-rail output swing Continuous output current: 3 ma Peak output
More informationPrecision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD8512
a FEATURES Fast Settling Time: 5 ns to.% Low Offset Voltage: V Max Low TcVos: V/ C Typ Low Input Bias Current: 25 pa Typ Dual-Supply Operation: 5 V to 5 V Low Noise: 8 nv/ Hz Low Distortion:.5% No Phase
More informationUltralow Offset Voltage Operational Amplifier OP07
Ultralow Offset Voltage Operational Amplifier OP07 FEATURES Low VOS: 75 μv maximum Low VOS drift:.3 μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise: 0.6 μv p-p maximum Wide input voltage
More informationZero Drift, Unidirectional Current Shunt Monitor AD8219
Zero Drift, Unidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to +85 V survival Buffered output voltage Gain = 6 V/V Wide operating temperature range:
More informationAD8601/AD8602/AD8604. Precision CMOS, Single-Supply, Rail-to-Rail, Input/Output Wideband Operational Amplifiers FEATURES PIN CONFIGURATIONS
Precision CMOS, Single-Supply, Rail-to-Rail, Input/Output Wideband Operational Amplifiers FEATURES Low offset voltage: 5 μv maximum Single-supply operation: 2.7 V to 5.5 V Low supply current: 75 μa/amplifier
More informationVery Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION
Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8273 FEATURES ±4 V HBM ESD Very low distortion.25% THD + N (2 khz).15% THD + N (1 khz) Drives 6 Ω loads Two gain settings Gain of
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD8 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V to
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp FEATURES True Single-Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single-Supply Capability from 3 V to 36
More information16 V Auto-Zero, Rail-to-Rail Output Operational Amplifiers AD8638/AD8639
6 V Auto-Zero, Rail-to-Rail Output Operational Amplifiers AD8638/AD8639 FEATURES Low offset voltage: 9 µv maximum Offset drift:.4 µv/ C maximum Rail-to-rail output swing 5 V to 6 V single-supply or ±2.5
More informationQuad 7 ns Single Supply Comparator AD8564
Quad 7 ns Single Supply Comparator AD8564 FEATURES 5 V single-supply operation 7 ns propagation delay Low power Separate input and output sections TTL/CMOS logic-compatible outputs Wide output swing TSSOP,
More informationAD8510/AD8512/AD8513. Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers FEATURES PIN CONFIGURATIONS
Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD5/AD5/AD5 FEATURES Fast settling time: 5 ns to.% Low offset voltage: μv maximum Low TCVOS: μv/ C typical
More informationImproved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
More information250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048
5 MHz, General Purpose Voltage Feedback Op Amps AD8/AD88 FEATURES Wide Bandwidth AD8, G = + AD88, G = + Small Signal 5 MHz 6 MHz Large Signal ( V p-p) MHz 6 MHz 5.8 ma Typical Supply Current Low Distortion,
More informationDual Low Offset, Low Power Operational Amplifier OP200
Dual Low Offset, Low Power Operational Amplifier OP200 FEATURES Low input offset voltage: 75 μv maximum Low offset voltage drift, over 55 C < TA < +25 C 0.5 μv/ C maximum Low supply current (per amplifier):
More informationDual Low Power Operational Amplifier, Single or Dual Supply OP221
a FEATURES Excellent TCV OS Match, 2 V/ C Max Low Input Offset Voltage, 15 V Max Low Supply Current, 55 A Max Single Supply Operation, 5 V to 3 V Low Input Offset Voltage Drift,.75 V/ C High Open-Loop
More informationQuad Low Offset, Low Power Operational Amplifier OP400
Quad Low Offset, Low Power Operational Amplifier OP4 FEATURES Low input offset voltage 5 μv max Low offset voltage drift over 55 C to 25 C,.2 pv/ C max Low supply current (per amplifier) 725 μa max High
More informationHigh Voltage, Current Shunt Monitor AD8215
High Voltage, Current Shunt Monitor AD825 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead
More informationHigh Common-Mode Voltage Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage Programmable Gain Difference Amplifier FEATURES High common-mode input voltage range ±12 V at VS = ±15 V Gain range.1 to 1 Operating temperature range: 4 C to ±85 C Supply voltage
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationSelf-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628 FEATURES FUNCTIONAL BLOCK DIAGRAM High common-mode input voltage range ±20 V at VS = ±5 V Gain range 0. to 00 Operating temperature
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V to
More informationHigh Voltage, Current Shunt Monitor AD8215
FEATURES ±4 V human body model (HBM) ESD High common-mode voltage range V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead SOIC: 4 C to + C Excellent
More informationUltralow Offset Voltage Operational Amplifier OP07
FEATURES Low VOS: 5 μv maximum Low VOS drift:. μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise:. μv p-p maximum Wide input voltage range: ± V typical Wide supply voltage range: ± V
More information1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-1/ADA4051-2
.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA-/ADA-2 FEATURES Very low supply current: 3 μa typical Low offset voltage: μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8
More informationAD8218 REVISION HISTORY
Zero Drift, Bidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to 85 V survival Buffered output voltage Gain = 2 V/V Wide operating temperature range:
More informationHigh Resolution, Zero-Drift Current Shunt Monitor AD8217
High Resolution, Zero-Drift Current Shunt Monitor AD8217 FEATURES High common-mode voltage range 4.5 V to 8 V operating V to 85 V survival Buffered output voltage Wide operating temperature range: 4 C
More informationREV. D Ultralow Distortion High Speed Amplifiers AD8007/AD8008 FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 5 MHz SO
Ultralow Distortion High Speed Amplifiers FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 dbc @ 5 MHz SOIC (R) SC7 (KS-5) 8 dbc @ MHz (AD87) AD87 AD87 NC V (Top View) 8 NC OUT
More informationLow Power, 350 MHz Voltage Feedback Amplifiers AD8038/AD8039
Low Power, MHz Voltage Feedback Amplifiers AD88/AD89 FEATURES Low power: ma supply current/amp High speed MHz, db bandwidth (G = +) V/μs slew rate Low cost Low noise 8 nv/ Hz @ khz fa/ Hz @ khz Low input
More informationLow Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2 AD8278/AD8279
Low Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2 /AD8279 FEATURES Wide input range beyond supplies Rugged input overvoltage protection Low supply current: 2 μa maximum (per amplifier)
More informationSingle-Supply 42 V System Difference Amplifier AD8205
Single-Supply 42 V System Difference Amplifier FEATURES Ideal for current shunt applications High common-mode voltage range 2 V to +65 V operating 5 V to +68 V survival Gain = 50 Wide operating temperature
More informationHigh Common-Mode Voltage Difference Amplifier AD629
a FEATURES Improved Replacement for: INAP and INAKU V Common-Mode Voltage Range Input Protection to: V Common Mode V Differential Wide Power Supply Range (. V to V) V Output Swing on V Supply ma Max Power
More informationUltralow Offset Voltage Dual Op Amp AD708
Ultralow Offset Voltage Dual Op Amp FEATURES Very high dc precision 30 μv maximum offset voltage 0.3 μv/ C maximum offset voltage drift 0.35 μv p-p maximum voltage noise (0. Hz to 0 Hz) 5 million V/V minimum
More informationLow Cost, High Speed Rail-to-Rail Amplifiers AD8091/AD8092
Low Cost, High Speed Rail-to-Rail Amplifiers AD891/AD892 FEATURES Low cost single (AD891) and dual (AD892) amplifiers Fully specified at +3 V, +5 V, and ±5 V supplies Single-supply operation Output swings
More informationDual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature
Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by
More informationPrecision, Low Power, Micropower Dual Operational Amplifier OP290
Precision, Low Power, Micropower Dual Operational Amplifier OP9 FEATURES Single-/dual-supply operation:. V to 3 V, ±.8 V to ±8 V True single-supply operation; input and output voltage Input/output ranges
More informationDual, High Voltage Current Shunt Monitor AD8213
Dual, High Voltage Current Shunt Monitor AD823 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range
More informationPrecision, Low Power, Micropower Dual Operational Amplifier OP290
a FEATURES Single-/Dual-Supply Operation, 1. V to 3 V,. V to 1 V True Single-Supply Operation; Input and Output Voltage Ranges Include Ground Low Supply Current (Per Amplifier), A Max High Output Drive,
More informationZero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP OP FUNCTIONAL BLOCK DIAGRAM FEATURES ENHANCED PRODUCT FEATURES
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP FEATURES Digitally/pin-programmable gain G = 1, 2, 4, 8, 16, 32, 64, or 128 Specified from 55 C to +125 C 5 nv/ C maximum input offset
More informationPrecision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608
Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD865/AD866/AD868 FEATURES Low offset voltage: 65 μv maximum Low input bias currents: pa maximum Low noise: 8 nv/ Hz Wide bandwidth:
More informationLow Cost, General Purpose High Speed JFET Amplifier AD825
a FEATURES High Speed 41 MHz, 3 db Bandwidth 125 V/ s Slew Rate 8 ns Settling Time Input Bias Current of 2 pa and Noise Current of 1 fa/ Hz Input Voltage Noise of 12 nv/ Hz Fully Specified Power Supplies:
More informationRail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
More informationQuad Low Offset, Low Power Operational Amplifier OP400
FEATURES Low input offset voltage: 5 µv maximum Low offset voltage drift over 55 C to 25 C:.2 μv/ C maximum Low supply current (per amplifier): 725 µa maximum High open-loop gain: 5 V/mV minimum Input
More informationLow Voltage Micropower Quad Operational Amplifier OP490
Low Voltage Micropower Quad Operational Amplifier FEATURES Single/dual-supply operation.6 V to 36 V ±0.8 V to ±8 V Single-supply operation; input and output voltage ranges include ground Low supply current:
More informationAD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES
Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable
More informationADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
More informationLow Cost Low Power Instrumentation Amplifier AD620
Low Cost Low Power Instrumentation Amplifier AD60 FEATURES Easy to use Gain set with one external resistor (Gain range to 0,000) Wide power supply range (±.3 V to ±8 V) Higher performance than 3 op amp
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier FEATURES High common-mode input voltage range ±2 V at VS = ± V Gain range. to Operating temperature range: 4 C to ±8 C Supply voltage range
More information9- and 11-Channel, Muxed Input LCD Reference Buffers AD8509/AD8511
9- and -Channel, Muxed Input LCD Reference Buffers AD8509/AD85 FEATURES Single-supply operation: 3.3 V to 6.5 V High output current: 300 ma Low supply current: 6 ma Stable with 000 pf loads Pin compatible
More informationOP SPECIFICATIONS ELECTRICAL CHARACTERISTICS (V S = ± V, T A = C, unless otherwise noted.) OPA/E OPF OPG Parameter Symbol Conditions Min Typ Max Min T
a FEATURES Excellent Speed:. V/ms Typ Fast Settling (.%): ms Typ Unity-Gain Stable High-Gain Bandwidth: MHz Typ Low Input Offset Voltage: mv Max Low Offset Voltage Drift: mv/ C Max High Gain: V/mV Min
More informationOBSOLETE. High-Speed, Dual Operational Amplifier OP271 REV. A. Figure 1. Simplified Schematic (One of the two amplifiers is shown.
a FEATURES Excellent Speed:. V/ms Typ Fast Settling (.%): ms Typ Unity-Gain Stable High-Gain Bandwidth: MHz Typ Low Input Offset Voltage: mv Max Low Offset Voltage Drift: mv/ C Max High Gain: V/mV Min
More informationUltralow Power, Rail-to-Rail Output Operational Amplifiers OP281/OP481
Ultralow Power, Rail-to-Rail Output Operational Amplifiers OP28/OP48 FEATURES Low supply current: 4 μa/amplifier maximum Single-supply operation: 2.7 V to 2 V Wide input voltage range Rail-to-rail output
More information