MCR08B, MCR08M. Thyristors. Surface Mount 600V - 800V > MCR08B, MCR08M G K. Description
|
|
- Conrad Scott
- 5 years ago
- Views:
Transcription
1 MCR8B, MCR8M Pb Description PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection circuits. Supplied in surface mount package for use in automated manufacturing. Features Sensitive Gate Trigger Current Blocking Voltage to 6 V Glass Passivated Surface for Reliability and Uniformity Surface Mount Package These Devices are Pb Free and are RoHS Compliant Functional Diagram Pin Out 4 A G K Additional Information Datasheet Resources Samples
2 Maximum Ratings (T J = 25 C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off State Voltage (Note 1) ( 4 to 125 C, Sine Wave, to 6 Hz, Gate Open) MCR8B MCR8M V DRM, V 2 RRM 6 V On-State RMS Current (All Conduction Angles; T C = 8 C) I T (RMS).8 A Peak Non-Repetitive Surge Current (1/2 Cycle Sine Wave, 6 Hz, T C = 25 C) I TSM 8. A Circuit Fusing Consideration (t = 8.3 ms) I 2 t.4 A²sec Forward Peak Gate Power (T C = 8 C, t = µs) P GM W Average Gate Power (t = 8.3 ms, T C = 8 C) P GM (AV).1 W Operating Junction Temperature Range T J -4 to +125 C Storage Temperature Range T stg -4 to +1 C Thermal Characteristics Rating Symbol Value Unit Thermal Resistance, Junction to Case (AC) PCB Mounted per Figure 1 R 8JC 2.2 C/W Thermal Resistance, Junction to Tab Measured on Anode Tab Adjacent to Epoxy Maximum Device Temperature for Soldering Purposes (for Seconds Maximum) R 8JT 25 C/W T L 26 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. V DRM and V RRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
3 Electrical Characteristics - OFF (T J = 25 C unless otherwise noted ; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak Repetitive Forward or Reverse Blocking Current (Note 3) (V AK = Rated V DRM or V RRM, R GK = 1 kq T J = 25 C I DRM, - - μa I RRM T J = 125 C ma Electrical Characteristics - ON (T J = 25 C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak Forward On-State Voltage (Note 2) (IT = A Peak) V TM 1.7 V Gate Trigger Current (Continuous ) (Note 4) (V AK = 12 V, R L = Ω) I GT 2 ma Gate Trigger Voltage (Continuous ) (V D = 12 V, R L = Ω) I H 5. ma Holding Current (Note 3) (VAK = 12 V, Initiating Current = 2 ma) V GT.8 V Turn On Time (VAK = 12 V, ITM = 5 A, IGT = 5 ma) tgt 1.25 µs 2. Pulse Test: Pulse Width 3 µs, Duty Cycle 2%. 3. RGK = Q is included in measurement. 4. RGK is not included in measurement. Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Critical Rate-of-Rise of Off State Voltage (Vpk = Rated VDRM, TC = 1 C, RGK = 1 kq, Exponential Method) dv/dt V/µs
4 Voltage Current Characteristic of SCR Symbol V DRM Parameter Peak Repetitive Forward Off State Voltage +C urrent Anode + V TM I DRM Peak Forward Blocking Current on state V RRM Peak Repetitive Reverse Off State Voltage I RRM at V RRM I H I RRM V TM I H Peak Reverse Blocking Current Maximum On State Voltage Holding Current Reverse Blocking Region (off state) Reverse Avalanche Region Anode +V oltage I DRM at V DRM Forward Blocking Region (off state) Figure 1. PCB for Thermal Impedance and Power Testing of SOT inches mm BOARD MOUNTED VERTICALLY IN CINCH 884 EDGE CONNECTOR. BOARD THICKNESS = 65 MIL., FOIL THICKNESS = 2.5 MIL. MATERIAL: G FIBERGLASS BASE EPOXY
5 Figure 2. On-State Characteristics Figure 3. Junction to Ambient Thermal Resistance vs Copper Tab Area I T TYPICAL AT T J = 1ϒC MAX AT T J = 1ϒC MAX AT T J = 25ϒC v T Figure 4. Current Derating, Minimum Pad Size Reference: Ambient Temperature Figure 5. Current Derating, cm Square Pad Reference: Ambient Temperature TA, MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( C) = 3 6 I 9 OR 6 Hz HALFWAVE TA, MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( C) = cm 2 FOIL, OR 6 Hz HALFWAVE I T(AV) Figure 6. Current Derating, 2. cm Square Pad Reference: Ambient Temperature Figure 7. Current Derating Reference: Anode Tab TA, MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( C) = PAD AREA = 4. cm 2, OR 6 Hz HALFWAVE I T(AV) T(tab), MAXIMUM ALLOWABLE TAB TEMPERATURE ( C) 1 = 3 6 OR 6 Hz HALFWAVE I T(AV)
6 Figure 8. Power Dissipation Figure 9. Thermal Response Device Mounted on Figure 1 Printed Circuit Board MAXIMUM AVERAGE POWER (AV),DISSIPATION (WATTS) P I T(AV) = r T, TRANSIENT THERMAL RESISTANCE NORMALIZED t, TIME (SECONDS) Figure. Typical Gate Trigger Voltage vs Junction Temperature Figure 11. Typical Normalized Holding Current vs Junction Temperature V GT, GATE TRIGGER VOLTAGE (VOLTS) V AK = 12 V R L = T J, JUNCTION TEMPERATURE, (ϒC) Figure 12. Typical Range of V GT versus Measured I GT Figure 13. Typical Gate Trigger Current vs Junction Temperature.7 V GT, GATE TRIGGER VOLTAGE (VOLTS) V AK = 12 V R L = T J = 25ϒC.3 I GT, GATE TRIGGER CURRENT ( A)
7 Figure 14. Holding Current Range vs Gate-Cathode Resistance Figure 15. Exponential Static dv/dt vs. Junction Temperature and Gate-Cathode Termination Resistance HOLDING CURRENT (ma) I H, I GT = 48 A,, R I GT = 7 A T J = 25ϒC STATIC dv/dt (V/ μ S) 5.,, R GK V pk = 4 V 75 T J = 25 Figure 16. Exponential Static dv/dt vs Peak Voltage and Gate-Cathode Termination Resistance Figure 17. Exponential Static dv/dt vs Gate-Cathode Capacitance and Resistance STATIC dv/dt (V/ μ S) 4 V 3 V 2 V V V V T J = 1 C STATIC dv/dt (V/ μ S) T J = 1 C 4 V (PEAK) R GK = R GK = k 5. 5.,.1 R GK = k 1. R GK C GK Figure 18. Exponential Static dv/dt vs Gate-Cathode Termination Resistance and Product Trigger Current Sensitivity STATIC dv/dt (V/ S) 5. I GT = 7 A I GT = 5 A I GT = 35 A I GT = 15 A,,
8 Dimensions Soldering Footprint D b H E E e1 e b (3) A1 A L1 C SCALE 6:1 mm inches Dim Inches Millimeters Min Nom Max Min Nom Max Part Marking System A A b b c D E e e L H E DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: INCH. 1 Pin Assignment SOT 223 CASE 318E STYLE 1 Cathode 2 Anode 3 Gate 1 AYW CR8x CR8x =D evice Code x = B or M A= Assembly Location Y= Year W= Work Week =P b Free Package (Note: Microdot may be in either location) 4 Anode Ordering Information Device Package Shipping MCR8BT1G SOT-223 (Pb-Free) /Tape & Reel Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: MCR8MT1G TO-223 (Pb-Free) /Tape & Reel
MAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationMCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationMCR8SDG, MCR8SMG, MCR8SNG
MCR8SDG, MCR8SMG, MCR8SNG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationC122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationMCR8DCM, MCR8DCN. Thyristors. Surface Mount 600V - 800V > MCR8DCM, MCR8DCN G K. Description
MCR8DCM, MCR8DCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationMCR25DG, MCR25MG, MCR25NG
MCR25DG, MCR25MG, MCR25NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More information2N6504 Series. Thyristors. Surface Mount V > 2N6504 Series. Description
2N6504 Series Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Glass Passivated Junctions for
More informationMAC16DG, MAC16MG, MAC16NG
MAC6DG, MAC6MG, MAC6NG Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800
More informationMCR12DCM, MCR12DCN. Thyristors. Surface Mount 400V - 800V > MCR12DCM, MCR12DCN G K. Description
MCR12DCM, MCR12DCN Pb Description This thyristor is designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon
More informationMAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
More informationMCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
More informationMAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
More informationMCR218-2G, MCR218-4G, MCR218-6G
MCR218-2G, MCR218-4G, MCR218-6G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half-wave silicon gate-controlled,
More informationMCR12DSM, MCR12DSN. Thyristors. Surface Mount 100V -600V > MCR12DSM, MCR12DSN G K. Description
MCR12DSM, MCR12DSN Thyristors Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control; CDI (Capacitive
More information2N6400. Thyristors. Surface Mount V > 2N6400. Description
2N6400 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More information2N6394. Thyristors. Surface Mount V > 2N6394. Description
2N6394 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies. Features Glass Passivated Junctions for Greater Parameter Uniformity
More informationMCR69-2, MCR69-3. Thyristors. Surface Mount V > MCR69-2, MCR69-3. Description. Designed for overvoltage protection in crowbar circuits.
1 2 3 Thyristors MCR69-2, MCR69-3 Pb Description Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and Reliability Center-Gate
More informationMCR12DG, MCR12MG, MCR12NG
MCR12DG, MCR12MG, MCR12NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMC4DCM, MAC4DCN. Thyristors. Surface Mount 600V - 800V > MC4DCM, MAC4DCN. Description
MCDCM, MACDCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size Surface
More informationC106 Series. Thyristors. Surface Mount > V > C106 Series TO 225AA CASE 77 STYLE 2. Description
C106 Series Pb Description Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability
More informationMAC12D, MAC12M, MAC12N
MAC12D, MAC12M, MAC12N Pb Description Designed for high performance full wave ac control applications where high noise immunity and commutating di/dt are required. Features Blocking Voltage to 800 Volts
More informationT2322B. Thyristors Surface Mount 200V > T2322B TO 225AA CASE 77 STYLE 2. Description
T2322B Pb Description Designed primarily for ac power switching. The gate sensitivity of these triacs permits the use of economical transistorized or integrated circuit control circuits, and it enhances
More informationMAC228A. Thyristors. Surface Mount 400V - 800V > MAC228A. Description
MAC228A Pb Description Designed primarily for industrial and consumer applications for full wave control of AC loads such as appliance controls, heater controls, motor controls, and other power switching
More informationBTA16-600BW3G, BTA16-800BW3G,
BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationMAC8DG, MAC8MG, MAC8NG
MAC8DG, MAC8MG, MAC8NG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMCR703A Series. Thyristors. Surface Mount 100V -600V > MCR703A Series G K. Description
MCR703 Series Pb Description PNPN devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationBTB08-600BW3G, BTB08-800BW3G
BTB08-600BW3G, BTB08-800BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationBTA25-600CW3G, BTA25-800CW3G
BTA25-600CW3G, BTA25-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationBTA08-800CW3G. Thyristors. Surface Mount 800V > BTA08-800CW3G. Description
BTA08-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage to 800 On-State
More informationBTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G
BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More informationMCR70xA Series. Thyristors. Surface Mount 100V -600V > MCR70xA Series G K. Description
MCR70x Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where
More informationBTA30H-600CW3G, BTA30H-800CW3G
BTA30H-600CW3G, BTA30H-800CW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationMCR106-6, MCR Thyristors. Surface Mount 400V - 600V > MCR106-6, MCR106-8 TO 225AA CASE 77 STYLE 2 G K. Description
MCR106-6, MCR106-8 Pb Description PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and
More information2N6344. Thyristors. Surface Mount V > 2N6344. Description
2N6344 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled
More informationMCR8DSM, MCR8DSN. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS VOLTS
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control;
More informationMCR100 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 A RMS 100 thru 600 V
MCR0 Series Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume, line-powered consumer applications such as relay and lamp drivers,
More informationThyristors Surface Mount 120V - 240V > MKP1V120 Series. Description. Features. Strobes and Flashers. Ignitors. High Voltage Regulators
MKP1V120 Series Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state
More informationUNISONIC TECHNOLOGIES CO., LTD
MCR00 UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS 3 2 SOT-23 SOT-223 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
More informationR L = 60 Ω. DC Gate Trigger Voltage. = 1 kω T J = 125 C = V DRM. / V RRM Exponential Waveform R GK I G. = 10mA PW = 15μsec I T. = 3.
S602ECS RoHS Description This new.8 A sensitive gate SCR in an TO-92 package with a GAK pin out, offers a high static component series with a high static dv/dt and a low turn off (t q ) time by the use
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6V I T(RMS) = 4 A I TSM = 4 A I GT = 5mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 4A) Gate Trigger Current : 5mA High commutation
More information2N6400 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 16 AMPERES RMS 50 thru 800 VOLTS
Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever halfwave silicon
More informationMCR8N. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever
More information2N6344A, 2N6348A, 2N6349A
2N6344A, 2N6348A, 2N6349A Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS SOT-89 3 2 SOT-23 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More information2N6071A/B Series. Thyristors. Surface Mount 200V-600W > 2N6071A/B Series. Description
2N6071A/B Series Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate
More informationDescription. Features. Strobes and Flashers. Ignitors. High Voltage Regulators. Pulse Generators. Functional Diagram. Additional Information
MKP3V120, MKP3V240 Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking
More information1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6 V I T(RMS) = 5 A I TSM = 6 A I GT = 35mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 5A) Gate Trigger Current : 35mA High commutation
More informationMCR106-6, MCR Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 AMPERES RMS 400 thru 600 VOLTS
MCR106-6, MCR106-8 Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume consumer applications such as temperature, light and speed
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 A RMS, Volts
C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light,
More informationP6SMB11AT3G Series. TVS Diodes. Surface Mount > 600W > P6SMB11AT3G Series. Bi-directional. Cathode. Anode. Uni-directional.
P6SMB11AT3G Series Pb Description The P6SMB11AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationSilicon Controlled Rectifiers
MCR692, MCR693 Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and
More information1.5SMC6.8AT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMC6.8AT3G. Bi-directional. Cathode. Anode. Uni-directional. Description
1.5SMC6.8AT3G Pb Description The 1.5SMC6.8AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationSamples. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV) Average on-state current T C
Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes
More informationCR02AM-8. Thyristor. Low Power Use. Features. Outline. Applications. Maximum Ratings. REJ03G Rev.1.00 Mar
Thyristor Low Power Use REJG4- Rev.. Mar.8. Features I T (AV) :. A V DRM : 4 V I GT : µa Planar Passivation Type Completed Pb free product Outline RENESAS Package code: PRSSDE-A (Package name: TO-9()).
More informationTeccor brand Thyristors Silicon Controlled Rectifiers
Sx02xS EV Series Amp Sensitive SCR Description New Amp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. All SCR s junctions are
More informationPINNING - TO220AB PIN CONFIGURATION SYMBOL
series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated thyristors in a plastic SYMBOL PARAMETER MAX. MAX. MAX. UNIT envelope, intended for use in applications requiring high - 4R 6R 8R bidirectional
More informationTeccor brand Thyristors 40 Amp Low T q SCR. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV)
RoHS Description The S4040xQx series of s offer fast turn-off time (tq) characteristics required for applications such as power inverters, switching regulator, and high frequency pulse circuits. These
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationTN B. Standard 15 A SCRs. Description. Features. Application. Benefits
Standard 15 A SCRs Description Datasheet - production data The TN1515-600B is a 15 A thyristor SCR housed in DPAK package. It fits any high voltage application that requires a high power density and compact
More informationDescription. Features & Benefits. RoHS compliant Glass passivated junctions. Applications. Additional Information. Datasheet
Sx01E & SxN1 Series RoHS Description Excellent for lower current heat, lamp, and audible alarm controls for home goods. Standard phase control SCRs are triggered with few milliamperes of current at less
More informationMARKING DIAGRAMS MAXIMUM RATINGS
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationMAC4DSM, MAC4DSN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationTeccor brand Thyristors 12 Amp Standard SCR. Symbol Parameter Test Conditions SRR6012x1 Unit I T(RMS) RMS on-state current T C
RoHS Description Excellent unidirectional switches for phase control and general switching applications such as heating, motor control controls, converters / rectifiers and capacitive discharge ignitions.
More informationS1VM02600A TO-92 (TO-226AA) SCRs 1.5 AMPERES RMS 600 VOLTS. Sensitive Gate Sillicon Controlled Rectifiers Reverse Blocking Thyristors FEATURES
LITE-ON SEMICONDUCTOR Sensitive Gate Sillicon Controlled Rectifiers Reverse Blocking Thyristors SCRs 1.5 AMPERES RMS 6 VOLTS FEATURES Sensitive Gate Allows Triggering by Microcontrollers and Other Logic
More informationPINNING - SOT82 PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated, sensitive gate SYMBOL PARAMETER MAX. MAX. MAX. UNIT thyristors in a plastic envelope, intended for use in general purpose BT8- R 5R 6R switching
More informationP0102DN. Sensitive 0.8 A SCR thyristor. Description. Features. Applications
Sensitive 0.8 A SCR thyristor Datasheet - production data Features A G K A G K A SOT-223 IT(RMS) 0.8 A 125 C max Tj Low 0.2 ma gate current 400 V VDRM/VRRM ECOPACK 2 compliant component Description Thanks
More information2N5060 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors nnular PNPN devices designed for high volume consumer applications such as relay and lamp drivers, small motor
More informationP0102AL. Sensitive high immunity 0.25 A SCR Thyristor. Description. Features. Applications
Sensitive high immunity 0.25 A SCR Thyristor Datasheet - production data Features IT(RMS) 0.25 A Low 200 µa gate current High noise immunity 200 V/µs ECOPACK 2 compliant component Description Thanks to
More information1SMA5.0AT3G Series. TVS Diodes. Surface Mount > 400W > 1SMA5.0AT3G Series. Bi-directional. Cathode. Anode. Uni-directional.
SMA5.0AT3G Series Pb Description The SMA5.0AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationQJxx16xHx Series. Thyristors 16 Amp High Temperature Alternistor Triacs. RoHS. Description
RoHS Description This 16A high temperature alternistor triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationTN1605H-6G. High temperature 16 A SCRs. Description. Features. Applications
High temperature 16 A SCRs Datasheet - production data G A A K Description Designed with high immunity switching to external surges, this device offers robust switching up to its 150 C maximum Tj. The
More informationPINNING - TO220AB PIN CONFIGURATION SYMBOL
series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated thyristors in a plastic SYMBOL PARAMETER MAX. MAX. MAX. UNIT envelope, intended for use in applications requiring high - 4R 6R 8R bidirectional
More informationMAC223A6, MAC223A8, MAC223A10. Triacs. Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 400 thru 800 VOLTS
MAC3A6, MAC3A8, MAC3A Triacs Preferred Device Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications such as lighting systems, heater controls, motor controls and power
More informationTeccor brand Thyristors EV Series 0.8 Amp Sensitive Triacs
LX8 Series RoHS Description New 0.8 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationFeatures. Samples. Symbol Parameter Value Unit TO-92 SOT-223. t p TO-92 SOT-223. = 2 x I GT. Peak gate current t p. = 10 μs T J
L01 Series RoHS Description New 1 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More information: PNPN DB3 : MCRB25D MCRB25M MCRB25N MCRB25H. Pin Polarity Circuit Diagram TO-220F, TO-220AB, TO-263 (D 2 PAK)
Designed primarily for half wave ac control applications, such asmotor controls, heating controls, and power supplies; or whereverhalf wave, silicon gate controlled devices are needed. Blocking Voltage
More informationThyristors 4 Amp High Temperature Sensitive SCRs. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 130 C 4 A I T(AV)
RoHS Description This SJxx4x high temperature SCR series is ideal for uni-directional switch applications such as phase control in heating, motor speed controls, converters/rectifiers and capacitive discharge
More informationFeatures. Symbol Parameter Value Unit TO-92 SOT-223. t p TO-92 SOT-223. Peak gate current t p. = 10 μs T J
Sx02xS Series RoHS Description New mp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. ll SCR s junctions are glasspassivated
More informationPINNING - TO220AB PIN CONFIGURATION SYMBOL. tab
GENERAL DESCRIPTION QUICK REFERENCE DATA Passivated, sensitive gate thyristors SYMBOL PARAMETER MAX. MAX. MAX. UNIT in a plastic envelope, intended for use in general purpose switching and BT58-5R 6R 8R
More information(1 A to 70 A) Features. Compak SCR
Selected Packages* File #E71639 U.L. RECONIZED TO-263 D 2 Pak TO-92 *TO-218 TO-252 D-Pak TO-22 *TO-218X 3-lead Compak *TO-22 TO-251 V-Pak (1 to 7 ) E6 eneral Description The Teccor line of thyristor SCR
More informationTM8050H-8W. 80 A high temperature Thyristor (SCR) Applications
80 A high temperature Thyristor (SCR) Datasheet - production data G TAB = A A K Applications Solid state switch Battery charging system Variable speed motor drive Industrial welding systems AC-DC rectifier
More informationPINNING - TO92 variant PIN CONFIGURATION SYMBOL. 3 anode g
BT9 series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated, sensitive gate SYMBOL PARAMETER MAX. MAX. MAX. MAX. UNIT thyristors in a plastic envelope, intended for use in general purpose BT9
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationT Phase Control Thyristor
The T820 is a high current disc pack SCR employing a high di/dt gate structure. This gate design allows the SCR to be reliably operated at high di/dt and dv/dt conditions in various phase control applications.
More informationSymbol Parameter Test Conditions Value Unit RMS on-state current T C = 75 C 0.8 A I T(AV) Average on-state current T C
EC103xx & SxSx Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Sensitive gate SCRs are easily triggered with micromps
More informationTIC106 SERIES SILICON CONTROLLED RECTIFIERS
TIC06 SERIES Copyright 999, Power Innovations Limited, UK APRIL 97 - REVISED JULY 2000 5 A Continuous On-State Current 30 A Surge-Current Glass Passivated Wafer 400 V to 800 V Off-State Voltage Max I GT
More informationReverse Blocking Thyristors
Preferred Device Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Glass Passivated Junctions
More informationMAC3030 8G. Triacs. Silicon Bidirectional Thyristors TRIACS 8.0 AMPERES RMS 250 VOLTS
Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever fullwave silicon
More informationBTA40 and BTA/BTB41 Series
STANDARD 4A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 4 A G V DRM /V RRM 6 and 8 V A1 A1 I GT (Q1 ) 5 ma G DESCRIPTION Available in high power packages, the BTA/ BTB4-41 series is suitable for general
More informationBTB16-600CW3G, BTB16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-CW3G, BTB-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More informationTN3050H-12GY-TR. 30 A V automotive grade SCR Thyristor. Description. Features. Applications
30 A - 1200 V automotive grade SCR Thyristor Datasheet - production data Features AEC-Q101 qualified High junction temperature: Tj = 150 C AC off state voltage: +/- 1200 V Nominal on-state current: 30
More informationSurface Mount > 600W > P6SMB11AT3G Series. Description. Features
P6SMB11AT3G Series Pb OBSOLETE/EOL DATE June/30/2018 PCN/ECN# LFPCN41246 REPLACED BY P6SMB Series Description The P6SMB11AT3G series is designed to protect voltage sensitive components from high voltage,
More information