MAC16DG, MAC16MG, MAC16NG
|
|
- Richard Cooper
- 5 years ago
- Views:
Transcription
1 MAC6DG, MAC6MG, MAC6NG Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800 Volts On State Current Rating of 6 Amperes RMS at 80 C Uniform Gate Trigger Currents in Three Quadrants High Immunity to dv/dt 500 V/µs minimum at 25 C Minimizes Snubber Networks for Protection Industry Standard TO 220 Package High Commutating di/dt 9.0 A/ms minimum at 25 C Pin Out These Devices are Pb Free and are RoHS Compliant Functional Diagram MT2 G MT CASE 22A STYLE 4 Additional Information 2 Datasheet Resources Samples
2 Maximum Ratings (T J = 25 C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off State Voltage (Note ) ( 40 to 25 C, Sine Wave, 50 to 60 Hz, Gate Open) MAC6D MAC6M MAC6N V DRM, 400 V RRM V On-State RMS Current (Full Cycle Sine Wave, 50 to 60 Hz, T C = 80 C) I T (RMS) 6 A Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, T J = 25 C) I TSM 50 A Circuit Fusing Consideration (t = 8.3 ms) I 2 t 93 A²sec Peak Gate Power (T C = +80 C, Pulse Width =.0 µs) P GM 20 W Average Gate Power (t = 8.3 ms, T C = 80 C) P G (AV) 0.5 W Operating Junction Temperature Range T J -40 to +25 C Storage Temperature Range T stg -40 to +50 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.. V DRM and V RRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Thermal Characteristics Rating Symbol Value Unit Thermal Resistance, Junction to Case (AC) Junction to Ambient R 8JC R 8JA C/W Maximum Lead Temperature for Soldering Purposes, /8 from case for 0 seconds T L 260 C
3 Electrical Characteristics - OFF (T J = 25 C unless otherwise noted ; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak Repetitive Blocking Current = V DRM = V RRM ; Gate Open) T J = 25 C I DRM, μa I RRM T J = 25 C ma Electrical Characteristics - ON (T J = 25 C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak On State Voltage (Note 2) (I TM = ±2 A Peak) V TM.2.6 V Gate Trigger Current (Continuous dc) = 2 V, R L = 00 Ω) Gate Trigger Voltage (Continuous dc) = 2 V, R L = 00 Ω) Latching Current = 24 V, I G = 35 ma) MT2(+), G(+) I GT MT2(+), G( ) MT2( ), G( ) MT2(+), G(+) V GT MT2(+), G( ) MT2( ), G( ) MT2(+), G(+) I L MT2(+), G( ) MT2( ), G( ) ma V ma Holding Current = 2 V dc, Gate Open, Initiating Current = ±50 ma)) I H ma Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. 2. Indicates Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Rate of Change of Commutating Current, See Figure 0. (VD = 400 V, ITM = 6.0 A, Commutating dv/dt = 24 V/µs, Gate Open, TJ = 25 C, f = 250 Hz, No Snubber) (di/dt)c 9.0 A/ms Critical Rate of Rise of Off-State Voltage = Rated V DRM, Exponential Waveform, Gate Open, T J = 25 C) dv/dt 600 V/µs
4 Voltage Current Characteristic of SCR Symbol Parameter +C urrent V DRM Peak Repetitive Forward Off State Voltage V TM Quadrant MainTerminal 2 + I DRM Peak Forward Blocking Current I RRM at V RRM on state I H V RRM I RRM V TM Peak Repetitive Reverse Off State Voltage Peak Reverse Blocking Current Maximum On State Voltage Quadrant 3 I H V TM off state +V oltage I DRM at V DRM I H Holding Current Quadrant Definitions for a Triac Quadrant II Quadrant I I Quadrant III Quadrant IV All polarities are referenced to MT. With in phase signals (using standard AC lines) quadrants I and III are used.
5 Figure. RMS Current Derating Figure 2. On-State Power Dissipation Figure 3. On State Characteristics Figure 4. Thermal Response r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) t, TIME (ms) Figure 5. Hold Current Variation 40 I H, HOLD CURRENT (ma) MT2 NEGATIVE MT2 POSITIVE 5 T J, JUNCTION TEMPERATURE (ϒC)
6 Figure 6. Typical Holding Current vs Junction Temperature Figure 7. Gate Trigger Voltage vs Junction Temperature IGT, GATE TRIGGER CURRENT (ma) 00 Q2 Q Q3 V D = 2 V R L = 00 VGT, GATE TRIGGER VOLTAGE (VOLT) Q Q2 V D = 2 V R L = 00 Q3 0.5 T J, JUNCTION TEMPERATURE (ϒC) T J, JUNCTION TEMPERATURE (ϒC) Figure 8. Critical Rate of Rise of Off State Voltage (Exponential) Figure 9. Critical Rate of Rise of Commutating Voltage (V/s ) μ K 3K 2K K V D = 800 Vpk T J = 25 C (dv/dt), CRITICAL RATE OF RISE OF (V/s μ ) c COMMUTATING VOLTAGE 0 T J = 25 C 00 C 75 C I TM V DRM t w f = 2 t w (di/dt) c = 6f I TM R G, GATE TO MAIN TERMINAL RESISTANCE (OHMS) (di/dt) c, RATE OF CHANGE OF COMMUTATING CURRENT (A/ms) Figure 0. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Current (di/dt)c L L N V RMS ADJUST FOR I TM, 60 Hz V AC MEASURE I CHARGE TRIGGER CHARGE CONTROL C L TRIGGER CONTROL N94 5 MT2 G MT V Note: Component values are for verification of rated (di/dt) c. See AN048 for additional information.
7 Dimensions Part Marking System SEATING PLANE B F T C S H Q Z L V G N D A K U R J 2 3 CASE 22A STYLE 4 x= D, M, or N A= Assembly Location Y= Year WW = Work Week MAC6xG AYWW Pin Assignment Dim Inches Millimeters Min Max Min Max A B C D F G H J K L N Q R S T U V Z Main Terminal 2 Main Terminal 2 3 Gate 4 Main Terminal 2 Ordering Information Device Package Shipping MAC6DG MAC6MG MAC6NG TO-220 (Pb-Free) 50 Units/ Rail. DIMENSIONING AND TOLERANCING PER ANSI Y4.5M, CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at:
MAC12D, MAC12M, MAC12N
MAC12D, MAC12M, MAC12N Pb Description Designed for high performance full wave ac control applications where high noise immunity and commutating di/dt are required. Features Blocking Voltage to 800 Volts
More informationMAC8DG, MAC8MG, MAC8NG
MAC8DG, MAC8MG, MAC8NG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
More informationBTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G
BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More informationMAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
More informationBTB08-600BW3G, BTB08-800BW3G
BTB08-600BW3G, BTB08-800BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationMCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
More informationBTA16-600BW3G, BTA16-800BW3G,
BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationBTA08-800CW3G. Thyristors. Surface Mount 800V > BTA08-800CW3G. Description
BTA08-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage to 800 On-State
More informationBTA25-600CW3G, BTA25-800CW3G
BTA25-600CW3G, BTA25-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage
More informationBTA30H-600CW3G, BTA30H-800CW3G
BTA30H-600CW3G, BTA30H-800CW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationMAC228A. Thyristors. Surface Mount 400V - 800V > MAC228A. Description
MAC228A Pb Description Designed primarily for industrial and consumer applications for full wave control of AC loads such as appliance controls, heater controls, motor controls, and other power switching
More informationC122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationMC4DCM, MAC4DCN. Thyristors. Surface Mount 600V - 800V > MC4DCM, MAC4DCN. Description
MCDCM, MACDCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size Surface
More informationMCR25DG, MCR25MG, MCR25NG
MCR25DG, MCR25MG, MCR25NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationMCR12DG, MCR12MG, MCR12NG
MCR12DG, MCR12MG, MCR12NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMCR8SDG, MCR8SMG, MCR8SNG
MCR8SDG, MCR8SMG, MCR8SNG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More information2N6400. Thyristors. Surface Mount V > 2N6400. Description
2N6400 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationMAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationMCR218-2G, MCR218-4G, MCR218-6G
MCR218-2G, MCR218-4G, MCR218-6G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half-wave silicon gate-controlled,
More information2N6504 Series. Thyristors. Surface Mount V > 2N6504 Series. Description
2N6504 Series Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Glass Passivated Junctions for
More informationMCR69-2, MCR69-3. Thyristors. Surface Mount V > MCR69-2, MCR69-3. Description. Designed for overvoltage protection in crowbar circuits.
1 2 3 Thyristors MCR69-2, MCR69-3 Pb Description Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and Reliability Center-Gate
More information2N6394. Thyristors. Surface Mount V > 2N6394. Description
2N6394 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies. Features Glass Passivated Junctions for Greater Parameter Uniformity
More informationMCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationT2322B. Thyristors Surface Mount 200V > T2322B TO 225AA CASE 77 STYLE 2. Description
T2322B Pb Description Designed primarily for ac power switching. The gate sensitivity of these triacs permits the use of economical transistorized or integrated circuit control circuits, and it enhances
More informationMCR8DCM, MCR8DCN. Thyristors. Surface Mount 600V - 800V > MCR8DCM, MCR8DCN G K. Description
MCR8DCM, MCR8DCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationMCR08B, MCR08M. Thyristors. Surface Mount 600V - 800V > MCR08B, MCR08M G K. Description
MCR8B, MCR8M Pb Description PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection
More informationC106 Series. Thyristors. Surface Mount > V > C106 Series TO 225AA CASE 77 STYLE 2. Description
C106 Series Pb Description Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability
More informationMCR12DCM, MCR12DCN. Thyristors. Surface Mount 400V - 800V > MCR12DCM, MCR12DCN G K. Description
MCR12DCM, MCR12DCN Pb Description This thyristor is designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon
More informationMCR12DSM, MCR12DSN. Thyristors. Surface Mount 100V -600V > MCR12DSM, MCR12DSN G K. Description
MCR12DSM, MCR12DSN Thyristors Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control; CDI (Capacitive
More information2N6344. Thyristors. Surface Mount V > 2N6344. Description
2N6344 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled
More informationBTA08-800CW3G. Triacs. Silicon Bidirectional Thyristors TRIACS 8 AMPERES RMS 800 VOLTS
BTA8-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationBTA25-600CW3G, BTA25-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTA-6CW3G, BTA-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationBTB16-600CW3G, BTB16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-CW3G, BTB-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationBTB16-600BW3G, BTB16-700BW3G, BTB16-800BW3G. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-BW3G, BTB-7BW3G, BTB-8BW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
More informationBTA25H-600CW3G, BTA25H-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTAH-600CW3G, BTAH-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationMAC16D, MAC16M, MAC16N. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 400 thru 800 VOLTS
MAC6D, MAC6M, MAC6N Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationBTA12-600C4G, BTA12-800C4G. Triacs Silicon Bidirectional Thyristors. TRIACS 12 AMPERES RMS 600 thru 800 VOLTS
BTA12-6C4G, BTA12-8C4G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More information2N6344A, 2N6348A, 2N6349A
2N6344A, 2N6348A, 2N6349A Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationMAC4DSM, MAC4DSN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationMAC3030 8G. Triacs. Silicon Bidirectional Thyristors TRIACS 8.0 AMPERES RMS 250 VOLTS
Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever fullwave silicon
More informationMCR703A Series. Thyristors. Surface Mount 100V -600V > MCR703A Series G K. Description
MCR703 Series Pb Description PNPN devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability
More informationMAC223A6, MAC223A8, MAC223A10. Triacs. Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 400 thru 800 VOLTS
MAC3A6, MAC3A8, MAC3A Triacs Preferred Device Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications such as lighting systems, heater controls, motor controls and power
More information2N6071A/B Series. Thyristors. Surface Mount 200V-600W > 2N6071A/B Series. Description
2N6071A/B Series Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate
More informationMCR106-6, MCR Thyristors. Surface Mount 400V - 600V > MCR106-6, MCR106-8 TO 225AA CASE 77 STYLE 2 G K. Description
MCR106-6, MCR106-8 Pb Description PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability
More informationMCR70xA Series. Thyristors. Surface Mount 100V -600V > MCR70xA Series G K. Description
MCR70x Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where
More informationMCR8N. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever
More information2N6344. Silicon Bidirectional Thyristors. TRIACS 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationMAC15 Series. Triacs. Silicon Bidirectional Thyristors. TRIACS 15 AMPERES RMS 400 thru 800 VOLTS
MAC5 Series Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as solidstate relays, motor controls, heating controls and power supplies; or wherever
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6V I T(RMS) = 4 A I TSM = 4 A I GT = 5mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 4A) Gate Trigger Current : 5mA High commutation
More information2N6400 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 16 AMPERES RMS 50 thru 800 VOLTS
Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever halfwave silicon
More informationSilicon Controlled Rectifiers
MCR692, MCR693 Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationMCR100 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 A RMS 100 thru 600 V
MCR0 Series Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume, line-powered consumer applications such as relay and lamp drivers,
More informationDescription. Features. Strobes and Flashers. Ignitors. High Voltage Regulators. Pulse Generators. Functional Diagram. Additional Information
MKP3V120, MKP3V240 Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6 V I T(RMS) = 5 A I TSM = 6 A I GT = 35mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 5A) Gate Trigger Current : 35mA High commutation
More informationT8M35T-B SERIES TRIACS 8 AMPERES RMS 600 VOLTS. Triacs Sillicon Bidirectional Thyristors TO-220AB FEATURES MECHANICAL DATA
LITE-ON SEMICONDUCTOR Triacs Sillicon Bidirectional Thyristors TRIACS 8 AMPERES RMS 600 VOLTS FEATURES Blocking Voltage to 600 Volts On-State Current Rating of 8.0 Amperes RMS at 0 Uniform Gate Trigger
More informationThyristors Surface Mount 120V - 240V > MKP1V120 Series. Description. Features. Strobes and Flashers. Ignitors. High Voltage Regulators
MKP1V120 Series Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state
More informationZ0107MA TRIACS 1.0 AMPERE RMS 600 VOLTS
Z7MA Sensitive ate Triacs Series Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an
More informationT12M50T600B TRIACS 12 AMPERES RMS 600 VOLTS. Triacs Sillicon Bidirectional Thyristors TO-220AB FEATURES MECHANICAL DATA
LITE-ON SEMICONDUCTOR Triacs Sillicon Bidirectional Thyristors TRIACS 12 AMPERES RMS VOLTS FEATURES Blocking Voltage to Volts On-state Current Rating of 12 Amperes RMS at 9 Uniform Gate Trigger Currents
More informationT12M5T-B SERIES TRIACS 12 AMPERES RMS 600 VOLTS. Sensitive Gate Triacs Sillicon Bidirectional Thyristors FEATURES TO-220AB MECHANICAL DATA
LITE-ON SEMICONDUCTOR Sensitive Gate Triacs Sillicon Bidirectional Thyristors TRIACS 2 AMPERES RMS 600 VOLTS FEATURES Sensitive Gate Allows Triggering by Microcontrollers and other Blocking Voltage to
More informationMCR8DSM, MCR8DSN. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS VOLTS
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control;
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive TO92
More informationBTA40 and BTA/BTB41 Series
STANDARD 4A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 4 A G V DRM /V RRM 6 and 8 V A1 A1 I GT (Q1 ) 5 ma G DESCRIPTION Available in high power packages, the BTA/ BTB4-41 series is suitable for general
More informationR L = 60 Ω. DC Gate Trigger Voltage. = 1 kω T J = 125 C = V DRM. / V RRM Exponential Waveform R GK I G. = 10mA PW = 15μsec I T. = 3.
S602ECS RoHS Description This new.8 A sensitive gate SCR in an TO-92 package with a GAK pin out, offers a high static component series with a high static dv/dt and a low turn off (t q ) time by the use
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 A RMS, Volts
C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light,
More informationQJxx16xHx Series. Thyristors 16 Amp High Temperature Alternistor Triacs. RoHS. Description
RoHS Description This 16A high temperature alternistor triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationNYE08-10B6TG. Protected TRIAC
NYE8-B6TG Protected TRIAC Silicon Bidirectional Thyristor Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive
More informationT2550H-600T 25A TRIACS MAIN FEATURES:
SNUBBERLESS HIGH TEMPERATURE 25A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 25 A V DRM /V RRM 600 V I GT (Q1 ) 50 ma DESCRIPTION Specifically designed for use in high temperature environment (found
More informationTeccor brand Thyristors EV Series 0.8 Amp Sensitive Triacs
LX8 Series RoHS Description New 0.8 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationT835T-8I. 8 A Snubberless Triac
8 A Snubberless Triac Datasheet - production data Features High static dv/dt High dynamic commutation 150 C maximum Tj Three quadrants Built-in ceramic for tab insulation Compliance to UL1557 standard
More informationT x V 25 A Snubberless Triac. Description. Features. Applications. Benefits
1200 V 25 A Snubberless Triac Description Datasheet production data Its 1200 V blocking voltage enables use in 3-phase industrial application. Its noise immunity and dynamic commutation makes it suitable
More informationFeatures. Samples. Symbol Parameter Value Unit TO-92 SOT-223. t p TO-92 SOT-223. = 2 x I GT. Peak gate current t p. = 10 μs T J
L01 Series RoHS Description New 1 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationMCR106-6, MCR Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 AMPERES RMS 400 thru 600 VOLTS
MCR106-6, MCR106-8 Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume consumer applications such as temperature, light and speed
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DESCRIPTION Passivated, sensitive gate triacs in a plastic envelope, intended for use in general purpose bidirectional switching and phase control applications, where high
More informationLJxx08xx & QJxx08xHx Series
RoHS Description This 8 A High Temperature Alternistor Triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationLJxx08xx & QJxx08xHx Series
LJxx8xx & QJxx8xHx Series RoHS Description This 8 A High Temperature Alternistor Triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature
More informationThyristors 12 Amp Alternistor (High Communitation) Triacs
Qxx12xHx Series RoHS Description This 12 Amp bidirectional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationT1635T-8FP. 16 A Snubberless Triac. Features. Applications. Description
16 A Snubberless Triac G A A1 Features Datasheet production data Medium current Triac High static and dynamic commutation Three quadrants ECOPACK compliant component Complies with UL standards (File ref:
More informationUNISONIC TECHNOLOGIES CO., LTD
MCR00 UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS 3 2 SOT-23 SOT-223 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
More informationACST1635-8FP. Overvoltage protected AC switch. Description. Features. Applications
Overvoltage protected AC switch Description Datasheet production data Features OUT COM TO-220FPAB Enables equipment to meet IEC 61000-4-5 surge with overvoltage crowbar technology High noise immunity against
More informationT9G Phase Control Thyristor
The T9G0 SCR employs a Center Fired amplifying gate structure which allows the SCR to be reliably operated at high di/dt and high dv/dt conditions in phase control applications. FEATURES: Low On-State
More informationMCR72-3, MCR72-6, MCR72-8. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 100 thru 600 VOLTS
MCR72-3, MCR72-6, MCR72-8 Sensitive ate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for industrial and consumer applications such as temperature, light and speed control; process
More information1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
More informationNGD8201B - 20 A, 400 V, N-Channel Ignition IGBT, DPAK
NGD8201B - 20 A, 400 V, N-Channel Ignition IGBT, DPAK Pb Description This Logic Level Insulated Gate Bipolar Transistor (IGBT) features monolithic circuitry integrating ESD and Over Voltage clamped protection
More informationACST310-8B. Overvoltage protected AC switch. Description. Features. Applications. Benefits
Overvoltage protected AC switch Datasheet production data Features AC switch with self over voltage protection Microcontroller direct driven (low gate current max. 10 ma) Three quadrants (Q1, Q2 and Q3)
More informationMBR20200CT. Switch mode Power Rectifier. Dual Schottky Rectifier SCHOTTKY BARRIER RECTIFIER 20 AMPERES, 200 VOLTS
MBRCT Switch mode Power Rectifier Dual Schottky Rectifier Features and Benefits Low Forward Voltage Low Power Loss/High Efficiency High Surge Capacity 75 C Operating Junction Temperature A Total ( A Per
More information1.5SMC6.8AT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMC6.8AT3G. Bi-directional. Cathode. Anode. Uni-directional. Description
1.5SMC6.8AT3G Pb Description The 1.5SMC6.8AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationT1235T-8R. 12 A Snubberless Triac. Description. Features. Applications
12 A Snubberless Triac Datasheet - production data Features A2 G I²PAK 12 A medium current Triac Three triggering quadrants device Very high noise immunity and dynamic commutation ECOPACK 2 compliant component
More information