C106 Series. Sensitive Gate Silicon Controlled Rectifiers
|
|
|
- Darleen Cannon
- 5 years ago
- Views:
Transcription
1 Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability of operation is important. Features Glassivated Surface for Reliability and Uniformity Power Rated at Economical Prices Practical Level Triggering and Holding Characteristics Flat, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability Sensitive Gate Triggering These are PbFree Devices MAXIMUM RATINGS (T J = 25 C unless otherwise noted) Characteristic Symbol Max Unit Peak Repetitive OffState Voltage (Note 1) (Sine Wave, 5060 Hz, R GK = 1 k, T C = 40 to 1 C) C6B C6D, C6D1* C6M, C6M1* On-State RMS Current (180 Conduction Angles, T C = 80 C) Average OnState Current (180 Conduction Angles, T C = 80 C) Peak Non-Repetitive Surge Current (1/2 Cycle, Sine Wave, 60 Hz, T J = +25 C) V DRM, V RRM V I T(RMS) 4.0 A I T(AV) 2.55 A I TSM 20 A Circuit Fusing Considerations (t = 8.3 ms) I 2 t 1.65 A 2 s Forward Peak Gate Power (Pulse Width 1.0 sec, T C = 80 C) Forward Average Gate Power (Pulse Width 1.0 sec, T C = 80 C) Forward Peak Gate Current (Pulse Width 1.0 sec, T C = 80 C) P GM 0.5 W P G(AV) 0.1 W I GM 0.2 A Operating Range T J 40 to +1 Storage Temperature Range T stg 40 to +150 Mounting Torque (Note 2) 6.0 in. lb. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. V DRM and V RRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. 2. Torque rating applies with use of compression washer (B52200F006). Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Anode lead and heatsink contact pad are common. C C SCRs 4 A RMS, Volts A TO225AA CASE 077 STYLE 2 MARKING DIAGRAM & PIN ASSIGNMENT 1. Cathode 2. Anode 3. Gate Y WW C6xx xx G ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. G K YWW C6xxG = Year = Work Week = Device Code = B, D, D1, M, M1 = PbFree Package September, 2011 Rev. 1 C6/D
2 THERMAL CHARACTERISTICS (T C = 25 C unless otherwise noted.) Characteristic Symbol Max Unit Thermal Resistance, JunctiontoCase R JC 3.0 C/W Thermal Resistance, JunctiontoAmbient R JA 75 C/W Maximum Lead Temperature for Soldering Purposes 1/8 in. from Case for Seconds T L 260 C ELECTRICAL CHARACTERISTICS (T C = 25 C unless otherwise noted.) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Peak Repetitive Forward or Reverse Blocking Current (V AK = Rated V DRM or V RRM, R GK = 1 k ) T J = 25 C T J = 1 C ON CHARACTERISTICS Peak Forward OnState Voltage (Note 3) (I TM = 4 A) Gate Trigger Current (Continuous dc) (Note 4) (V AK = 6 Vdc, R L = 0 ) T J = 25 C T J = 40 C I DRM, I RRM 0 A A V TM 2.2 V Peak Reverse Gate Voltage (I GR = A) V GRM 6.0 V Gate Trigger Voltage (Continuous dc) (Note 4) (V AK = 6 Vdc, R L = 0 ) T J = 25 C T J = 40 C Gate NonTrigger Voltage (Continuous dc) (Note 4) (V AK = 12 V, R L = 0, T J = 1 C) Latching Current (V AK = 12 V, I G = 20 ma, R GK = 1 k ) T J = 25 C T J = 40 C Holding Current (V D = 12 Vdc) (Initiating Current = 20 ma, R GK = 1 k ) T J = 25 C T J = 40 C T J = +1 C DYNAMIC CHARACTERISTICS I GT V GT V GD 0.2 V I L I H A V ma ma Critical RateofRise of OffState Voltage (V AK = Rated V DRM, Exponential Waveform, R GK = 1 k, T J = 1 C) dv/dt 8.0 V/ s 3. Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. 4. R GK is not included in measurement. 2
3 Voltage Current Characteristic of SCR + Current Anode + Symbol V DRM I DRM V RRM I RRM V TM I H Parameter Peak Repetitive Off State Forward Voltage Peak Forward Blocking Current Peak Repetitive Off State Reverse Voltage Peak Reverse Blocking Current Peak On State Voltage Holding Current I RRM at V RRM on state Reverse Blocking Region (off state) Reverse Avalanche Region V TM I H + Voltage I DRM at V DRM Forward Blocking Region (off state) Anode T C, CASE TEMPERATURE ( C) HALF SINE WAVE RESISTIVE OR INDUCTIVE LOAD. 50 to 400 Hz I T(AV) AVERAGE ON STATE CURRENT (AMPERES) DC Figure 1. Average Current Derating P (AV), AVERAGE ON STATE POWER DISSIPATION (WATTS) HALF SINE WAVE RESISTIVE OR INDUCTIVE LOAD 50 TO 400Hz. JUNCTION TEMPERATURE 1 C I T(AV) AVERAGE ON STATE CURRENT (AMPERES) Figure 2. Maximum OnState Power Dissipation DC 3
4 0 00 I GT, GATE TRIGGER CURRENT ( A) I H, HOLDING CURRENT ( A) Figure 3. Typical Gate Trigger Current versus Figure 4. Typical Holding Current versus , GATE TRIGGER VOLTAGE (V) I L, LATCHING CURRENT ( A) 0 VGT Figure 5. Typical Gate Trigger Voltage versus Figure 6. Typical Latching Current versus 4
5 PACKAGE INTERCHANGEABILITY The dimensional diagrams below compare the critical dimensions of the ON Semiconductor C-6 package with competitive devices. It has been demonstrated that the smaller dimensions of the ON Semiconductor package make it compatible in most lead-mount and chassis-mount applications. The user is advised to compare all critical dimensions for mounting compatibility DIA TYP BSC ON Semiconductor C-6 Package Competitive C-6 Package ORDERING INFORMATION C6BG C6DG C6D1G* C6MG C6M1G* Device Package Shipping TO225AA (PbFree) TO225AA (PbFree) TO225AA (PbFree) TO225AA (PbFree) TO225AA (PbFree) *D1 signifies European equivalent for D suffix and M1 signifies European equivalent for M suffix. 5
6 PACKAGE DIMENSIONS TO225 CASE 7709 ISSUE Z H Q B U F A K V G S D 2 PL M C J R 0.25 (0.0) M A M B M 0.25 (0.0) M A M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: INCH THRU -08 OBSOLETE, NEW STANDARD INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D F G BSC 2.39 BSC H J K M 5 TYP 5 TYP Q R S U V STYLE 2: PIN 1. CATHODE 2. ANODE 3. GATE 6
C106 Series. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 A RMS, Volts
C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light,
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers
C106 Series. Thyristors. Surface Mount > V > C106 Series TO 225AA CASE 77 STYLE 2. Description
C106 Series Pb Description Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability
2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
MCR106-6, MCR Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 AMPERES RMS 400 thru 600 VOLTS
MCR106-6, MCR106-8 Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume consumer applications such as temperature, light and speed
2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
C122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
2N6400 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 16 AMPERES RMS 50 thru 800 VOLTS
Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever halfwave silicon
MCR106-6, MCR Thyristors. Surface Mount 400V - 600V > MCR106-6, MCR106-8 TO 225AA CASE 77 STYLE 2 G K. Description
MCR106-6, MCR106-8 Pb Description PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability
MCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
Silicon Controlled Rectifiers
MCR692, MCR693 Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and
2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
MCR8DSM, MCR8DSN. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS VOLTS
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control;
MCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
MCR8N. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever
T2322B. Thyristors Surface Mount 200V > T2322B TO 225AA CASE 77 STYLE 2. Description
T2322B Pb Description Designed primarily for ac power switching. The gate sensitivity of these triacs permits the use of economical transistorized or integrated circuit control circuits, and it enhances
MCR218-2G, MCR218-4G, MCR218-6G
MCR218-2G, MCR218-4G, MCR218-6G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half-wave silicon gate-controlled,
MCR12DCM, MCR12DCN. Thyristors. Surface Mount 400V - 800V > MCR12DCM, MCR12DCN G K. Description
MCR12DCM, MCR12DCN Pb Description This thyristor is designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon
2N6400. Thyristors. Surface Mount V > 2N6400. Description
2N6400 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
MCR100 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 A RMS 100 thru 600 V
MCR0 Series Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume, line-powered consumer applications such as relay and lamp drivers,
2N6394. Thyristors. Surface Mount V > 2N6394. Description
2N6394 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies. Features Glass Passivated Junctions for Greater Parameter Uniformity
2N6504 Series. Thyristors. Surface Mount V > 2N6504 Series. Description
2N6504 Series Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Glass Passivated Junctions for
MCR69-2, MCR69-3. Thyristors. Surface Mount V > MCR69-2, MCR69-3. Description. Designed for overvoltage protection in crowbar circuits.
1 2 3 Thyristors MCR69-2, MCR69-3 Pb Description Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and Reliability Center-Gate
MCR12DG, MCR12MG, MCR12NG
MCR12DG, MCR12MG, MCR12NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
MCR8DCM, MCR8DCN. Thyristors. Surface Mount 600V - 800V > MCR8DCM, MCR8DCN G K. Description
MCR8DCM, MCR8DCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
MCR8SDG, MCR8SMG, MCR8SNG
MCR8SDG, MCR8SMG, MCR8SNG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
Reverse Blocking Thyristors
Preferred Device Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning
2N6071A/B Series. Thyristors. Surface Mount 200V-600W > 2N6071A/B Series. Description
2N6071A/B Series Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate
MAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
MCR12DSM, MCR12DSN. Thyristors. Surface Mount 100V -600V > MCR12DSM, MCR12DSN G K. Description
MCR12DSM, MCR12DSN Thyristors Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control; CDI (Capacitive
MCR25DG, MCR25MG, MCR25NG
MCR25DG, MCR25MG, MCR25NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
BTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
MAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
MAC3030 8G. Triacs. Silicon Bidirectional Thyristors TRIACS 8.0 AMPERES RMS 250 VOLTS
Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever fullwave silicon
MAC12D, MAC12M, MAC12N
MAC12D, MAC12M, MAC12N Pb Description Designed for high performance full wave ac control applications where high noise immunity and commutating di/dt are required. Features Blocking Voltage to 800 Volts
MCR08B, MCR08M. Thyristors. Surface Mount 600V - 800V > MCR08B, MCR08M G K. Description
MCR8B, MCR8M Pb Description PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection
MAC8DG, MAC8MG, MAC8NG
MAC8DG, MAC8MG, MAC8NG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
MAC228A. Thyristors. Surface Mount 400V - 800V > MAC228A. Description
MAC228A Pb Description Designed primarily for industrial and consumer applications for full wave control of AC loads such as appliance controls, heater controls, motor controls, and other power switching
MAC16DG, MAC16MG, MAC16NG
MAC6DG, MAC6MG, MAC6NG Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800
BTB08-600BW3G, BTB08-800BW3G
BTB08-600BW3G, BTB08-800BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G
BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
2N5060 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors nnular PNPN devices designed for high volume consumer applications such as relay and lamp drivers, small motor
BTA12-600C4G, BTA12-800C4G. Triacs Silicon Bidirectional Thyristors. TRIACS 12 AMPERES RMS 600 thru 800 VOLTS
BTA12-6C4G, BTA12-8C4G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
BTB16-600BW3G, BTB16-700BW3G, BTB16-800BW3G. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-BW3G, BTB-7BW3G, BTB-8BW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
MAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
MAC4DSM, MAC4DSN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
BTB16-600CW3G, BTB16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-CW3G, BTB-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
MAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
BTA08-800CW3G. Triacs. Silicon Bidirectional Thyristors TRIACS 8 AMPERES RMS 800 VOLTS
BTA8-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
BTA25H-600CW3G, BTA25H-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTAH-600CW3G, BTAH-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
MC4DCM, MAC4DCN. Thyristors. Surface Mount 600V - 800V > MC4DCM, MAC4DCN. Description
MCDCM, MACDCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size Surface
BTA30H-600CW3G, BTA30H-800CW3G
BTA30H-600CW3G, BTA30H-800CW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
MCR72-3, MCR72-6, MCR72-8. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 100 thru 600 VOLTS
MCR72-3, MCR72-6, MCR72-8 Sensitive ate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for industrial and consumer applications such as temperature, light and speed control; process
BTA16-600BW3G, BTA16-800BW3G,
BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
BTA25-600CW3G, BTA25-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTA-6CW3G, BTA-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
MCR70xA Series. Thyristors. Surface Mount 100V -600V > MCR70xA Series G K. Description
MCR70x Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where
BTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
BTA25-600CW3G, BTA25-800CW3G
BTA25-600CW3G, BTA25-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage
MAC15 Series. Triacs. Silicon Bidirectional Thyristors. TRIACS 15 AMPERES RMS 400 thru 800 VOLTS
MAC5 Series Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as solidstate relays, motor controls, heating controls and power supplies; or wherever
MCR703A Series. Thyristors. Surface Mount 100V -600V > MCR703A Series G K. Description
MCR703 Series Pb Description PNPN devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability
BTA08-800CW3G. Thyristors. Surface Mount 800V > BTA08-800CW3G. Description
BTA08-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage to 800 On-State
2N6344. Silicon Bidirectional Thyristors. TRIACS 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever
MARKING DIAGRAMS MAXIMUM RATINGS
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light
2N6344A, 2N6348A, 2N6349A
2N6344A, 2N6348A, 2N6349A Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon
MAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
Silicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive TO92
Reverse Blocking Thyristors
Preferred Device Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Glass Passivated Junctions
2N6344. Thyristors. Surface Mount V > 2N6344. Description
2N6344 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled
NYE08-10B6TG. Protected TRIAC
NYE8-B6TG Protected TRIAC Silicon Bidirectional Thyristor Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive
MAC223A6, MAC223A8, MAC223A10. Triacs. Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 400 thru 800 VOLTS
MAC3A6, MAC3A8, MAC3A Triacs Preferred Device Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications such as lighting systems, heater controls, motor controls and power
Z0107MA TRIACS 1.0 AMPERE RMS 600 VOLTS
Z7MA Sensitive ate Triacs Series Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an
UNISONIC TECHNOLOGIES CO., LTD
MCR00 UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS 3 2 SOT-23 SOT-223 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
2N5060 Series. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors SILICON CONTROLLED RECTIFIERS 0.
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors nnular PNPN devices designed for high volume consumer applications such as relay and lamp drivers, small motor
MAC16D, MAC16M, MAC16N. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 400 thru 800 VOLTS
MAC6D, MAC6M, MAC6N Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
MCR68 2. Silicon Controlled Rectifiers Reverse Blocking Thyristors. SCRs 12 AMPERES RMS 50 VOLTS
MCR682 Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for overvoltage protection in crowbar circuits. Features lass-passivated Junctions for reater Parameter Stability and Reliability
UNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS SOT-89 3 2 SOT-23 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
MBR2045CT, MBRF2045CT. SWITCHMODE Power Rectifier SCHOTTKY BARRIER RECTIFIER 20 AMPERES, 45 VOLTS
SWITCHMODE Power Rectifier Features and Benefits Low Forward Voltage Low Power Loss / High Efficiency High Surge Capacity 175 C Operating Junction Temperature 2 A Total ( A Per Diode Leg) PbFree Package
Symbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6V I T(RMS) = 4 A I TSM = 4 A I GT = 5mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 4A) Gate Trigger Current : 5mA High commutation
: PNPN DB3 : MCRB25D MCRB25M MCRB25N MCRB25H. Pin Polarity Circuit Diagram TO-220F, TO-220AB, TO-263 (D 2 PAK)
Designed primarily for half wave ac control applications, such asmotor controls, heating controls, and power supplies; or whereverhalf wave, silicon gate controlled devices are needed. Blocking Voltage
MARKING DIAGRAMS MAXIMUM RATINGS
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light
Teccor brand Thyristors Silicon Controlled Rectifiers
Sx02xS EV Series Amp Sensitive SCR Description New Amp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. All SCR s junctions are
C106 Series High Sensitive SCRs
is lassivated PNPN devices designed for high volume consumerapplications such as temperature, light, and speed control; process andremote control, and warning systems where reliability of operation isimportant.
Symbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6 V I T(RMS) = 5 A I TSM = 6 A I GT = 35mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 5A) Gate Trigger Current : 35mA High commutation
LDR3 Outline Dimensions. Dimension Inches Millimeters
OUTLINE DRAWING Dual SCR Module 5 Amperes / 16-18 Volts Ordering Information: Select the complete eight-digit module part number from the table below. Example: LDR3165 is a 16V, 5 Ampere Dual SCR Isolated
Value Unit I T(RMS) RMS on-state current A A Tj = 25 C I FSM current (Tj initial = 25 C)
MAIN FEATURES: DIODE / SCR MODULE Symbol Value Unit I T(RMS) 50-70-85 A V DRM /V RRM 800 and 1200 V I GT 50 and 100 ma DESCRIPTION Packaged in ISOTOP modules, the MDS Series is based on the half-bridge
SCR/GTO/Diode POW-R-BLOK Modules Ratings and Characteristics. 1.3 The Device Data Sheet
1.3 The Device Data Sheet The proper application of power semiconductors requires an understanding of their maximum ratings and electrical characteristics, information which is presented within the device
Phase Control Thyristor RMS SCRs, 25 A, 35 A
VS-N681, VS-N Series Phase Control Thyristor RMS SCRs, A, 3 A TO-8 (TO-8AA) V DRM /V RRM PRIMARY CHARACTERISTICS I T(AV) 16 A, A I T(RMS) A, 3 A 3 V, V, V, 6 V, 7 V, 8 V, V, V, 1 V, 1 V, V, V, 1 V 1 V
Samples. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV) Average on-state current T C
Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes
ST300S SERIES 300A. Features. Typical Applications. Major Ratings and Characteristics. Bulletin I25158 rev. B 01/94. case style TO-209AE (TO-118)
ST300S SERIES PHASE CONTROL THYRISTORS Stud Version Features Center amplifying gate Hermetic metal case with ceramic insulator International standard case TO-209AE (TO-118) Threaded studs UNF 3/4-16UNF2A
MKP1V120 Series. Sidac High Voltage. Bidirectional Triggers 0.9 AMPERES RMS VOLTS
MKP112 Series Sidac High oltage Bidirectional Triggers Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches
Teccor brand Thyristors 40 Amp Low T q SCR. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV)
RoHS Description The S4040xQx series of s offer fast turn-off time (tq) characteristics required for applications such as power inverters, switching regulator, and high frequency pulse circuits. These
R L = 60 Ω. DC Gate Trigger Voltage. = 1 kω T J = 125 C = V DRM. / V RRM Exponential Waveform R GK I G. = 10mA PW = 15μsec I T. = 3.
S602ECS RoHS Description This new.8 A sensitive gate SCR in an TO-92 package with a GAK pin out, offers a high static component series with a high static dv/dt and a low turn off (t q ) time by the use
S1VM02600A TO-92 (TO-226AA) SCRs 1.5 AMPERES RMS 600 VOLTS. Sensitive Gate Sillicon Controlled Rectifiers Reverse Blocking Thyristors FEATURES
LITE-ON SEMICONDUCTOR Sensitive Gate Sillicon Controlled Rectifiers Reverse Blocking Thyristors SCRs 1.5 AMPERES RMS 6 VOLTS FEATURES Sensitive Gate Allows Triggering by Microcontrollers and Other Logic
MBR60H100CTG. SWITCHMODE Power Rectifier 100 V, 60 A SCHOTTKY BARRIER RECTIFIER 60 AMPERES 100 VOLTS
SWITCHMODE Power Rectifier 1 V, 6 A Features and Benefits Low Forward Voltage:.72 V @ 125 C Low Power Loss/High Efficiency High Surge Capacity 175 C Operating Junction Temperature 6 A Total (3 A Per Diode
MCR22-6, MCR22-8 Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 1.5 AMPERES RMS 400 thru 600 VOLTS
MCR22-6, MCR22-8 referred evice Sensitive ate Silicon Controlled Rectifiers Reverse Blocking Thyristors esigned and tested for repetitive peak operation required for C ignition, fuel ignitors, flash circuits,
MBR735, MBR745. SWITCHMODE Power Rectifiers. SCHOTTKY BARRIER RECTIFIERS 7.5 AMPERES 35 and 45 VOLTS
MBR735, MBR75 SWITCHMODE Power Rectifiers Features and Benefits Low Forward Voltage Low Power Loss/High Efficiency High Surge Capacity 75 C Operating Junction Temperature PbFree Packages are Available*
PINNING - TO220AB PIN CONFIGURATION SYMBOL
series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated thyristors in a plastic SYMBOL PARAMETER MAX. MAX. MAX. UNIT envelope, intended for use in applications requiring high - 4R 6R 8R bidirectional
Phase Control SCR, 70 A
Phase Control SCR, 70 A 70TPS..PbF High oltage Series ishay High Power Products 2 (A) DESCRIPTION/FEATURES The 70TPS..PbF High oltage Series of silicon controlled rectifiers are specifically designed for
Silicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to