2N6344A, 2N6348A, 2N6349A
|
|
- Ashlie Bishop
- 5 years ago
- Views:
Transcription
1 2N6344A, 2N6348A, 2N6349A Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled solid-state devices are needed. Triac type thyristors switch from a blocking to a conducting state for either polarity of applied anode voltage with positive or negative gate triggering. Features Blocking Voltage to 8 V All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability Pin Out Small, Rugged, Thermowatt Construction for Low Thermal Resistance, High Heat Dissipation and Durability Gate Triggering Guaranteed in all Four Quadrants For 4 Hz Operation, Consult Factory 8. A Devices Available as 2N6344 thru 2N6349 Pb Free Package is Available CASE 221A STYLE 4 Functional Diagram 1 2 Additional nformation Datasheet Resources Samples
2 Maximum Ratings and Thermal Characteristics (T J = 25 C unless otherwise noted) Rating Symbol Value Unit *Peak Repetitive Off-State Voltage (Note 1) (T J = -4 to 11 C, Sine Wave, 5 to 6 Hz, Gate Open) 2N6344A, 6 2N6348A V DRM, V RRM 2N6349A 8 V *On-State RMS Current (Full Cycle Sine Wave 5 to 6 Hz) (T C =+8 C) T (RMS) 12 (T C =+9 C) 6. A *Peak Non Repetitive Surge Current (One Full Cycle, Sine Wave 6 Hz, T C = +8 C) Preceded and followed by rated current TSM 1 A Circuit Fusing Considerations (t = 8.3 ms) 2 t 59 A²s *Peak Gate Power (T C = +8 C, Pulse Width = 2 µs) P GM W *Average Gate Power (T C = +8 C, t = 8.3 ms) P G(AV).5 W *Peak Gate Current (T C = +8 C, Pulse Width = 2. µs) GM 2. A *Peak Gate Voltage (T C = +8 C, Pulse Width = 2. µs) V GM ±1 V *Operating Junction Temperature Range T J -4 to +15 C *Storage Temperature Range T stg -4 to +15 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. * ndicates JEDEC Registered Data. 1. V DRM and V RRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Thermal Characteristics Rating Symbol Value Unit * Thermal Resistance, Junction to Case R 8JC 2. C/W Maximum Lead Temperature for Soldering Purposes, 1/8 from case for 1 seconds T L 26 C
3 Electrical Characteristics - OFF (T C = 25 C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit *Peak Repetitive Blocking Current (V D = V DRM = V RRM ; Gate Open) T J = 25 C DRM, µa RRM T J = 11 C ma Electrical Characteristics - ON (T C = 25 C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak On State Voltage ( TM = ±17 A Peak; Pulse Width = 1 to 2 ms, Duty Cycle 2%) V TM V Gate Trigger Current (Continuous dc) (V D = 12 Vdc, R L = 1 Q) Quadrant : MT2(+), G(+) All Quadrant : MT2(+), G( ) 2N6348A & 2N6349A Quadrant : MT2( ), G( ) All Quadrant V: MT2( ), G(+) 2N6348A & 2N6349A GT ma MT2(+), G(+); MT2( ), G( ) T C = 4 C - 1 MT2(+), G( ); MT2( ), G(+) T C = 4 C Gate Trigger Voltage (Continuous dc) (V D = 12 Vdc, R L = 1 Q) Quadrant : MT2(+), G(+) Both.9 2. Quadrant : MT2(+), G( ) 2N6349 only Quadrant : MT2( ), G( ) Both Quadrant V: MT2( ), G(+) 2N6349 only V GT V MT2(+), G(+); MT2( ), G( ) TC = 4 C T C = 4 C 2.5 MT2(+), G( ); MT2( ), G(+) TC = 4 C T C = 4 C 3. Gate Non Trigger Voltage (Continuous dc) V GD MT2(+), G(+); MT2( ), G( ); MT2(+), G( ); MT2( ), G( ) TC = 25 C H TC = -4 C ma Turn-On Time (V D = Rated V DRM, TM = 11 A, GT = 1 ma, t gt µs ndicates JEDEC Registered Data.
4 Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Critical Rate of Rise of Commutation Voltag (V D = Rated V DRM, TM = 17 A, Commutating di/dt = 6.1 A/ms, Gate Unenergized, T C = 8 C) dv/dt(c) V/µs Voltage Current Characteristic of Triacs (Bidirectional Device) Symbol Parameter V DRM Peak Repetitive Forward Off State Voltage DRM V RRM Peak Forward Blocking Current Peak Repetitive Reverse Off State Voltage RRM Peak Reverse Blocking Current V TM Maximum On State Voltage H Holding Current Quadrant Definitions for a Triac Quadrant Quadrant Quadrant Quadrant V All polarities are referenced to MT1. With in phase signals (using standard AC lines) quadrants and are used.
5 Ratings and Characteristic Curves Figure 1. RMS Current Derating Figure 2. On State Power Dissipation 11 3 dc T, CASE TEMPERATURE ( C) C = CONDUCTON ANGLE dc T(RMS), RMS ON-STATE CURRENT, (AMP) P AV, AVERAGE POWER (WATTS) T J = 11 C = CONDUCTON ANGLE = T(RMS), RMS ON-STATE CURRENT (AMP) Figure 3. Typical Gate Trigger Voltage Figure 4. Typical Gate Trigger Current V gt, GATE TRGGER VOLTAGE (VOLTS) QUADRANTS QUADRANT 4 V D = 12 V GT, GATE TRGGER CURRENT (ma) QUADRANT V D = 12 V.4 T J, JUNCTON TEMPERATURE ( C) T J, JUNCTON TEMPERATURE ( C)
6 Figure 7. Maximum On-State Characteristics Figure 8. Typical Holding Current i TM, NSTANTANEOUS ON-STATE CURRENT (AMP) T J = 1 C 25 C v TM, NSTANTANEOUS ON-STATE VOLTAGE (VOLTS) 4.4 H, HOLDNG CURRENT (ma) MAN TERMNAL #2 POSTVE MAN TERMNAL #1 POSTVE GATE OPEN T J, JUNCTON TEMPERATURE ( C) Figure 9. Maximum Allowable Surge Current, PEAK SURGE CURRENT (AMP) TSM CYCLE T J = 1 C f = 6 Hz Surge is preceded and followed by rated current NUMBER OF CYCLES Figure 1. Typical Thermal Response r(t), TRANSENT THERMAL RESSTANCE(NORMALZED) Z JC(t) = r(t) R JC k 2. k k 1 k t,tme (ms)
7 Dimensions Part Marking System SEATNG PLANE B F T C S Q 4 A H Z 12 3 K U 1 2 CASE 221A STYLE 4 L R V G N D J Dim nches Millimeters Min Max Min Max Pin Assignment A B C D F G H J K L N Q R S T U V Z Ordering nformation Device Package Shipping 2N6344A 2N6344AG 2N6348A 2N6348AG 1 Main Terminal 1 2 Main Terminal 2 3 Gate 4 Main Terminal 2 (Pb-Free) (Pb-Free) 5 Units / Box 1. DMENSONNG AND TOLERANCNG PER ANS Y14.5M, CONTROLLNG DMENSON: NCH. 3. DMENSON Z DEFNES A ZONE WHERE ALL BODY AND LEAD RREGULARTES ARE ALLOWED. 2N6349A 2N6349AG (Pb-Free)
2N6344. Thyristors. Surface Mount V > 2N6344. Description
2N6344 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled
More information2N6071A/B Series. Thyristors. Surface Mount 200V-600W > 2N6071A/B Series. Description
2N6071A/B Series Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate
More informationMAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
More information2N6394. Thyristors. Surface Mount V > 2N6394. Description
2N6394 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies. Features Glass Passivated Junctions for Greater Parameter Uniformity
More information2N6400. Thyristors. Surface Mount V > 2N6400. Description
2N6400 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More information2N6504 Series. Thyristors. Surface Mount V > 2N6504 Series. Description
2N6504 Series Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Glass Passivated Junctions for
More informationC122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationMCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
More informationMAC228A. Thyristors. Surface Mount 400V - 800V > MAC228A. Description
MAC228A Pb Description Designed primarily for industrial and consumer applications for full wave control of AC loads such as appliance controls, heater controls, motor controls, and other power switching
More informationMAC3030 8G. Triacs. Silicon Bidirectional Thyristors TRIACS 8.0 AMPERES RMS 250 VOLTS
Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever fullwave silicon
More informationMAC223A6, MAC223A8, MAC223A10. Triacs. Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 400 thru 800 VOLTS
MAC3A6, MAC3A8, MAC3A Triacs Preferred Device Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications such as lighting systems, heater controls, motor controls and power
More informationMAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
More information2N6344. Silicon Bidirectional Thyristors. TRIACS 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationMCR69-2, MCR69-3. Thyristors. Surface Mount V > MCR69-2, MCR69-3. Description. Designed for overvoltage protection in crowbar circuits.
1 2 3 Thyristors MCR69-2, MCR69-3 Pb Description Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and Reliability Center-Gate
More informationMAC8DG, MAC8MG, MAC8NG
MAC8DG, MAC8MG, MAC8NG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMCR218-2G, MCR218-4G, MCR218-6G
MCR218-2G, MCR218-4G, MCR218-6G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half-wave silicon gate-controlled,
More informationBTB08-600BW3G, BTB08-800BW3G
BTB08-600BW3G, BTB08-800BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationMCR8SDG, MCR8SMG, MCR8SNG
MCR8SDG, MCR8SMG, MCR8SNG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationT2322B. Thyristors Surface Mount 200V > T2322B TO 225AA CASE 77 STYLE 2. Description
T2322B Pb Description Designed primarily for ac power switching. The gate sensitivity of these triacs permits the use of economical transistorized or integrated circuit control circuits, and it enhances
More informationMAC12D, MAC12M, MAC12N
MAC12D, MAC12M, MAC12N Pb Description Designed for high performance full wave ac control applications where high noise immunity and commutating di/dt are required. Features Blocking Voltage to 800 Volts
More informationMCR25DG, MCR25MG, MCR25NG
MCR25DG, MCR25MG, MCR25NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationMAC15 Series. Triacs. Silicon Bidirectional Thyristors. TRIACS 15 AMPERES RMS 400 thru 800 VOLTS
MAC5 Series Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as solidstate relays, motor controls, heating controls and power supplies; or wherever
More informationThyristors Surface Mount 120V - 240V > MKP1V120 Series. Description. Features. Strobes and Flashers. Ignitors. High Voltage Regulators
MKP1V120 Series Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state
More informationBTA16-600BW3G, BTA16-800BW3G,
BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationBTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G
BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More informationMCR12DG, MCR12MG, MCR12NG
MCR12DG, MCR12MG, MCR12NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMAC16DG, MAC16MG, MAC16NG
MAC6DG, MAC6MG, MAC6NG Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800
More informationMAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationBTA25-600CW3G, BTA25-800CW3G
BTA25-600CW3G, BTA25-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage
More informationDescription. Features. Strobes and Flashers. Ignitors. High Voltage Regulators. Pulse Generators. Functional Diagram. Additional Information
MKP3V120, MKP3V240 Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking
More informationBTA08-800CW3G. Thyristors. Surface Mount 800V > BTA08-800CW3G. Description
BTA08-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage to 800 On-State
More informationBTA30H-600CW3G, BTA30H-800CW3G
BTA30H-600CW3G, BTA30H-800CW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More information2N6400 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 16 AMPERES RMS 50 thru 800 VOLTS
Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever halfwave silicon
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationMC4DCM, MAC4DCN. Thyristors. Surface Mount 600V - 800V > MC4DCM, MAC4DCN. Description
MCDCM, MACDCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size Surface
More informationMCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationMCR12DCM, MCR12DCN. Thyristors. Surface Mount 400V - 800V > MCR12DCM, MCR12DCN G K. Description
MCR12DCM, MCR12DCN Pb Description This thyristor is designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationSilicon Controlled Rectifiers
MCR692, MCR693 Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and
More informationMCR8DCM, MCR8DCN. Thyristors. Surface Mount 600V - 800V > MCR8DCM, MCR8DCN G K. Description
MCR8DCM, MCR8DCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6V I T(RMS) = 4 A I TSM = 4 A I GT = 5mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 4A) Gate Trigger Current : 5mA High commutation
More informationBTA12-600C4G, BTA12-800C4G. Triacs Silicon Bidirectional Thyristors. TRIACS 12 AMPERES RMS 600 thru 800 VOLTS
BTA12-6C4G, BTA12-8C4G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationC106 Series. Thyristors. Surface Mount > V > C106 Series TO 225AA CASE 77 STYLE 2. Description
C106 Series Pb Description Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and
More informationBTB16-600BW3G, BTB16-700BW3G, BTB16-800BW3G. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-BW3G, BTB-7BW3G, BTB-8BW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6 V I T(RMS) = 5 A I TSM = 6 A I GT = 35mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 5A) Gate Trigger Current : 35mA High commutation
More informationMCR8N. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationMCR08B, MCR08M. Thyristors. Surface Mount 600V - 800V > MCR08B, MCR08M G K. Description
MCR8B, MCR8M Pb Description PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection
More informationBTB16-600CW3G, BTB16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-CW3G, BTB-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationMAC4DSM, MAC4DSN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationBTA25H-600CW3G, BTA25H-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTAH-600CW3G, BTAH-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationMCR12DSM, MCR12DSN. Thyristors. Surface Mount 100V -600V > MCR12DSM, MCR12DSN G K. Description
MCR12DSM, MCR12DSN Thyristors Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control; CDI (Capacitive
More informationMCR106-6, MCR Thyristors. Surface Mount 400V - 600V > MCR106-6, MCR106-8 TO 225AA CASE 77 STYLE 2 G K. Description
MCR106-6, MCR106-8 Pb Description PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability
More informationBTA08-800CW3G. Triacs. Silicon Bidirectional Thyristors TRIACS 8 AMPERES RMS 800 VOLTS
BTA8-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive TO92
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationBTA25-600CW3G, BTA25-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTA-6CW3G, BTA-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationSensitive Triacs. ( Amps) Features
Selected Packages* U.L. RECOGNIZED File #E71639 TO - 92 THERMOTAB TO-22AB TO-22AB G Sensitive Triacs (.8 8. ) 11 General Description Teccor's line of sensitive gate triacs includes devices with current
More informationReverse Blocking Thyristors
Preferred Device Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Glass Passivated Junctions
More informationMAC16D, MAC16M, MAC16N. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 400 thru 800 VOLTS
MAC6D, MAC6M, MAC6N Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationTriacs. ( Amps) Features
Selected Packages* U.L. RECOGNIZED File #E71639 THERMOTAB TO-22AB TO - 92 TO-22AB G Triacs (.8 25 ) 2 General Description These gated triacs from Teccor Electronics are part of a broad line of bidirectional
More informationMCR106-6, MCR Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 AMPERES RMS 400 thru 600 VOLTS
MCR106-6, MCR106-8 Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume consumer applications such as temperature, light and speed
More informationMCR100 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 A RMS 100 thru 600 V
MCR0 Series Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume, line-powered consumer applications such as relay and lamp drivers,
More informationThyristors 12 Amp Alternistor (High Communitation) Triacs
Qxx12xHx Series RoHS Description This 12 Amp bidirectional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationMCR8DSM, MCR8DSN. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS VOLTS
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control;
More informationMCR703A Series. Thyristors. Surface Mount 100V -600V > MCR703A Series G K. Description
MCR703 Series Pb Description PNPN devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability
More informationMCR70xA Series. Thyristors. Surface Mount 100V -600V > MCR70xA Series G K. Description
MCR70x Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where
More informationZ0107MA TRIACS 1.0 AMPERE RMS 600 VOLTS
Z7MA Sensitive ate Triacs Series Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an
More informationBTA40 and BTA/BTB41 Series
STANDARD 4A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 4 A G V DRM /V RRM 6 and 8 V A1 A1 I GT (Q1 ) 5 ma G DESCRIPTION Available in high power packages, the BTA/ BTB4-41 series is suitable for general
More informationT1635T-8FP. 16 A Snubberless Triac. Features. Applications. Description
16 A Snubberless Triac G A A1 Features Datasheet production data Medium current Triac High static and dynamic commutation Three quadrants ECOPACK compliant component Complies with UL standards (File ref:
More informationMCR72-3, MCR72-6, MCR72-8. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 100 thru 600 VOLTS
MCR72-3, MCR72-6, MCR72-8 Sensitive ate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for industrial and consumer applications such as temperature, light and speed control; process
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DESCRIPTION Passivated, sensitive gate triacs in a plastic envelope, intended for use in general purpose bidirectional switching and phase control applications, where high
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 A RMS, Volts
C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light,
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers
More informationQJxx16xHx Series. Thyristors 16 Amp High Temperature Alternistor Triacs. RoHS. Description
RoHS Description This 16A high temperature alternistor triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationUNISONIC TECHNOLOGIES CO., LTD
MCR00 UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS 3 2 SOT-23 SOT-223 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
More informationFeatures. Samples. Symbol Parameter Value Unit TO-92 SOT-223. t p TO-92 SOT-223. = 2 x I GT. Peak gate current t p. = 10 μs T J
L01 Series RoHS Description New 1 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationTeccor brand Thyristors EV Series 0.8 Amp Sensitive Triacs
LX8 Series RoHS Description New 0.8 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationDescription. Features. As low as 8mA max holding current. UL Recognized TO- 220AB package. 110 C rated junction temperature
Q6012xH1LED Series RoHS Description Q6012LH1LED series is designed to meet low load current characteristics typical in LED lighting applications. By keeping holding current at 8mA maximum, this Triac series
More informationBTA A Snubberless Triacs. Features. Description. I T(RMS) = 20 A V DRM, V RRM = 600 and 700 V I GT (Q1) (max) = 35 and 50 ma
20 A Snubberless Triacs Datasheet production data Features I T(RMS) = 20 A V DRM, V RRM = 600 and 700 V I GT (Q1) (max) = 35 and 50 ma Description G A2 A1 The Triacs use high performance glass passivated
More informationTeccor brand Thyristors 4 / 6 / 8 / 10 / 15 Amp Quadracs
QxxxxLTx Series RoHS Description The Quadrac is an internally triggered Triac designed for AC switching and phase control applications. It is a Triac and DIAC in a single package, which saves user expense
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS SOT-89 3 2 SOT-23 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
More informationSCT25N60FD 600V, 25A STANDARD TRIAC. Features. Applications. Ordering Information. Absolute Maximum Ratings (Limiting Values)
Triac 600V, 25A STANDARD TRIAC This device is suitable for low power AC switching application, phase control application such as fan speed and temperature modulation control, lighting control and static
More informationT2550H-600T 25A TRIACS MAIN FEATURES:
SNUBBERLESS HIGH TEMPERATURE 25A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 25 A V DRM /V RRM 600 V I GT (Q1 ) 50 ma DESCRIPTION Specifically designed for use in high temperature environment (found
More informationSamples. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV) Average on-state current T C
Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes
More informationTIC106 SERIES SILICON CONTROLLED RECTIFIERS
TIC06 SERIES Copyright 999, Power Innovations Limited, UK APRIL 97 - REVISED JULY 2000 5 A Continuous On-State Current 30 A Surge-Current Glass Passivated Wafer 400 V to 800 V Off-State Voltage Max I GT
More informationDescription. Features. As low as 8mA max holding current. UL Recognized TO- 220AB package. 110 C rated junction temperature
Q612LTH1LED Series RoHS Agency Approval Agency Agency File Number Description The Quadrac is an internally triggered Triac designed for AC switching and phase control applications. It is a Triac and DIAC
More informationSCT04N60FD 600V, 4A STANDARD TRIAC. Features. Applications. Ordering Information. Absolute Maximum Ratings (Limiting Values)
Triac 600V, 4A STANDARD TRIAC This device is suitable for low power AC switching application, phase control application such as fan speed and temperature modulation control, lighting control and static
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DESCRIPTION Glass passivated triac in a full pack plastic envelope, intended for use in applications requiring high bidirectional transient and blocking voltage capability
More informationT x V 25 A Snubberless Triac. Description. Features. Applications. Benefits
1200 V 25 A Snubberless Triac Description Datasheet production data Its 1200 V blocking voltage enables use in 3-phase industrial application. Its noise immunity and dynamic commutation makes it suitable
More informationLJxx08xx & QJxx08xHx Series
LJxx8xx & QJxx8xHx Series RoHS Description This 8 A High Temperature Alternistor Triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature
More informationLJxx08xx & QJxx08xHx Series
RoHS Description This 8 A High Temperature Alternistor Triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DESCRIPTION Glass passivated, sensitive gate triacs in a full pack plastic envelope, intended for use in general purpose bidirectional switching and phase control applications,
More informationTIC225 SERIES SILICON TRIACS
Copyright 997, Power Innovations Limited, UK JULY 975 - REVISED MARCH 997 Sensitive Gate Triacs 8 A RMS, 70 A Peak Glass Passivated Wafer 400 V to 800 V Off-State Voltage Max I GT of 5 ma (Quadrant ) MT
More information