LT1009 Series 2.5V Reference FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION
|
|
|
- Roy Wilkins
- 6 years ago
- Views:
Transcription
1 LT9 Series.5V Reference FEATURES n Maximum Initial Tolerance:.% n Guaranteed Temperature Stability n Maximum.6Ω Dynamic Impedance n Wide Operating Current Range n Directly Interchangeable with LM6 for Improved Performance n No Adjustments Needed for Minimum Temperature Coeffi cient n Available in 8-Lead SO and MSOP Packages and -Lead TO-9 Package APPLICATIONS n Reference for 5V Systems n 8-Bit A/D and D/A Reference n Digital Voltmeters n Current Loop Measurement and Control Systems n Power Supply Monitor DESCRIPTION The LT 9 is a precision trimmed.5v shunt regulator diode featuring a maximum initial tolerance of only ±5mV. The low dynamic impedance and wide operating current range enhances its versatility. The.% reference tolerance is achieved by on-chip trimming which not only minimizes the initial voltage tolerance but also minimizes the temperature drift. Even though no adjustments are needed with the LT9, a third terminal allows the reference voltage to be adjusted ±5% to calibrate out system errors. In many applications, the LT9 can be used as a pin-to-pin replacement of the LM6 and the external trim network eliminated. For a lower drift.5v reference, see the LT9 data sheet. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. ICAL APPLICATION.5V Reference Output Voltage 5V TO 5V.5.6k.5 LT9 k* TRIM *DOES NOT AFFECT TEMPERATURE COEFFICIENT. ±5% TRIM RANGE OUTPUT 9 TA REFEREE VOLTAGE (V) GUARANTEED MAXIMUM GUARANTEED MINIMUM ICAL TEMPERATURE ( C) 9 TA
2 LT9 Series ABSOLUTE MAXIMUM RATINGS (Note ) Reverse Current...mA Forward Current...mA Storage Temperature Range C to 5 C Lead Temperature (Soldering, sec)... C Operating Temperature Range LT9/LT9C... C to 7 C LT9I... C to 85 C LT9M (OBSOLETE) C to 5 C PIN CONFIGURATION BOTTOM VIEW ( ) TOP VIEW 8 () 7 6 () 5 H PACKAGE -LEAD TO-6 METAL CAN T JMAX = 5 C, θ JA = C/W, θ JC = 8 C/W OBSOLETE PACKAGE Consider the MS8, S8 or Z Packages for Alternate Source MS8 PACKAGE 8-LEAD PLASTIC MSOP T JMAX = 5 C, θ JA = 5 C/W TOP VIEW BOTTOM VIEW 8 7 () 6 () ( ) S8 PACKAGE 8-LEAD PLASTIC SO T JMAX = 5 C, θ JA = 9 C/W 5 Z PACKAGE -LEAD PLASTIC TO-9 T JMAX = C, θ JA = 6 C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LT9MH#PBF LT9MH#TRPBF -Lead TO-6 Metal Can 55 C to 5 C LT9CH#PBF LT9CH#TRPBF -Lead TO-6 Metal Can C to 7 C LT9CMS8#PBF LT9CMS8#TRPBF LTQZ 8-Lead Plastic MSOP C to 7 C LT9S8#PBF LT9S8#TRPBF 9 8-Lead Plastic SO C to 7 C LT9IS8#PBF LT9IS8#TRPBF 9I 8-Lead Plastic SO C to 85 C LT9CZ#PBF LT9CZ#TRPBF -Lead Plastic TO-9 C to 7 C LT9IZ#PBF LT9IZ#TRPBF -Lead Plastic TO-9 C to 85 C
3 LT9 Series ORDER INFORMATION LEAD BASED FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LT9MH LT9MH#TR -Lead TO-6 Metal Can 55 C to 5 C LT9CH LT9CH#TR -Lead TO-6 Metal Can C to 7 C LT9CMS8 LT9CMS8#TR LTQZ 8-Lead Plastic MSOP C to 7 C LT9S8 LT9S8#TR 9 8-Lead Plastic SO C to 7 C LT9IS8 LT9IS8#TR 9I 8-Lead Plastic SO C to 85 C LT9CZ LT9CZ#TR -Lead Plastic TO-9 C to 7 C LT9IZ LT9IZ#TR -Lead Plastic TO-9 C to 85 C Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. For more information on lead free part marking, go to: For more information on tape and reel specifi cations, go to: AVAILABLE OPTIONS TEMPERATURE PACKAGE STYLE TEMPERATURE ACCURACY (%) COEFFICIENT (ppm/ C) TO-6 (H) OBSOLETE MSOP-8 (MS8) SO-8 (S8) C to 7 C. 5 LT9CH. 5 LT9CMS8 LT9S8 C to 85 C LT9IS8 55 C to 5 C. 5 LT9MH TO-9 (Z) LT9CZ LT9IZ ELECTRICAL CHARACTERISTICS The l denotes the specifi cations which apply over the full operating temperature range, otherwise specifi cations are at T A = 5 C. SYMBOL PARAMETER V Z Reverse Breakdown Voltage ΔV Z ΔI R r Z ΔV Z ΔTemp ΔV Z ΔTime Reverse Breakdown Change with Current Reverse Dynamic Impedance CONDITIONS T A = 5 C, I R = ma H, Z Pkg MS, S Pkg μa I R ma l LTM LT9I LT9/LT9C MIN MAX MIN MAX MIN MAX I R = ma Ω l Ω Temperature Stability T MIN T A T MAX l mv Average Temperature Coefficient (Notes, ) C T A 7 C C T A 85 C 55 C T A 5 C UNITS V V mv mv 5 5 ppm/ C ppm/ C ppm/ C Long-Term Stability T A = 5 C ±. C, I R = ma ppm/khr Note : Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note : Guaranteed by Design. Note : Average temperature coeffi cient is defi ned as the total voltage change divided by the specifi ed temperature change.
4 LT9 Series ICAL PERFORMAE CHARACTERISTICS Reverse Characteristics Forward Characteristics Reverse Voltage Change. 5 T J = 5 C REVERSE CURRENT (A) T J = 5 C T J = 5 C T J = 55 C FORWARD VOLTAGE (V) REVERSE VOLTAGE CHANGE (mv) REVERSE VOLTAGE (V) 9 G... FORWARD CURRENT (ma) 9 G 8 6 REVERSE CURRENT (ma) 9 G DYNAMIC IMPEDAE (Ω). Dynamic Impedance Output Noise Voltage Response Time I R = ma 55 C T J 5 C k k k FREQUEY (Hz) NOISE (nv/ Hz) 5 5 I R = ma T J = 5 C 5 k k k FREQUEY (Hz) VOLTAGE SWING (V) INPUT OUTPUT 5k INPUT OUTPUT TIME (μs) 9 G 9 G5 9 G6
5 SCHEMATIC DIAGRAM LT9 Series Q7 Q k k 6.6k Q8 Q7 pf k pf Q 5Ω Q Q Q Q9 k 6.6k Q6 Q Q Q5 7Ω Q 9 SD ICAL APPLICATIONS Wide Supply Range, Adjustable Reference Low Temperature Coeffi cient Power Regulator.6V TO V V LM V R 6Ω V IN LT7A IN OUT.k 75Ω V OUT LT9 k LT9 9 TA k 9 TA Switchable ±.5V Bipolar Reference 5V 5k 5V 5V 5k LT9 k % OUT 9.76k % 5Ω 9 TA5 5k 5V 5
6 LT9 Series PACKAGE DESCRIPTION H Package -Lead and -Lead TO-6 Metal Can (Reference LTC DWG # 5-8-).9.9 ( ) (.5.95).5 (.7) MIN REFEREE PLANE.6.9** (.6.8) DIA.85.5 ( ).5 (.65) MAX SEATING* PLANE.5 (.7).6.6 (.9.68). (.5) PIN * LEAD DIAMETER IS UONTROLLED BETWEEN THE REFEREE PLANE AND.5" BELOW THE REFEREE PLANE.6. ** FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS (.6.6) 5 OBSOLETE PACKAGE.5 (.7) FOR -LEAD PACKAGE ONLY.8.8 (.7.9) H/(TO-6) 8 MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # ).. (.8.) (NOTE ) (.5) REF 5. (.6) MIN..8 (.65.5) (.5.5)..5 (.6.6).65 (.56) BSC RECOMMENDED SOLDER PAD LAYOUT GAUGE PLANE.8 (.7).5 (.) DETAIL A DETAIL A NOTE:. DIMENSIONS IN MILLIMETER/(IH). DRAWING NOT TO SCALE (..6) SEATING PLANE.9.5 (.9.6). (.) MAX..8 (.9.5).65 (.56) BSC. DIMENSION DOES NOT ILUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED.5mm (.6") PER SIDE. DIMENSION DOES NOT ILUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED.5mm (.6") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE.mm (.") MAX.. (.8.) (NOTE ).86 (.) REF.6.58 (..) MSOP (MS8) 7 REV F 6
7 PACKAGE DESCRIPTION S8 Package 8-Lead Plastic Small Outline (Narrow.5 Inch) (Reference LTC DWG # 5-8-6) LT9 Series.5 BSC.5 ± (.8 5.) NOTE MIN.6 ±.5.8. ( ).5.57 (.8.988) NOTE. ±.5 RECOMMENDED SOLDER PAD LAYOUT.8. (..5).. (.5.58) (.6.75).. (..5) (.6.7) (.55.8) NOTE: IHES. DIMENSIONS IN (MILLIMETERS). DRAWING NOT TO SCALE. THESE DIMENSIONS DO NOT ILUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED.6" (.5mm).5 (.7) BSC SO8 Z Package -Lead Plastic TO-9 (Similar to TO-6) (Reference LTC DWG # 5-8-).6.5 (.5.7) DIA.8.5 (.57.7).8.5 (.57.7).9 (.86) NOM.5 (.7) MIN.5 UONTROLLED (.7) LEAD DIMENSION MAX 5 NOM.5 (.7) BSC BULK PACK.6. (.6.76).6. (.5.5).5. (.8.5) Z (TO-9) 8 REV C.98.6/. (.5./.) PLCS TO-9 TAPE AND REEL REFER TO TAPE AND REEL SECTION OF LTC DATA BOOK FOR ADDITIONAL INFORMATION.. (.556.7) NOM Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 7
8 LT9 Series ICAL APPLICATION Low Noise.5V Buffered Reference μf V IN 6V k k LT9 k k k μf μf 7 LTC 6.5V 9 TA6 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT9 Precision Series Reference Bandgap,.5%, 5ppm/ C LT6 Precision Series Reference 5V and V Zener-Based 5ppm/ C, SO-8 Package LTC 798 Micropower Low Dropout Series Reference.5% Max, 6.5μA Supply Current LT6 Micropower Precision Series Reference Bandgap, μa Supply Current ppm/ C, Available in SOT- LT6 Micropower Precision Shunt Voltage Reference Bandgap.5%, ppm/ C, μa Supply Current LT6 Micropower Precision Series Reference.% Max, ppm/ C Max, 5μA Supply Current 8 LT 9 REV F PRINTED IN USA Linear Technology Corporation 6 McCarthy Blvd., Milpitas, CA (8) -9 FAX: (8) LINEAR TECHNOLOGY CORPORATION 985
FEATURES DESCRIPTIO TYPICAL APPLICATIO. LM / LM /LM Micropower Voltage Reference APPLICATIO S
Micropower Voltage Reference FEATRES 2µA to 2mA Operating Range Guaranteed % Initial Voltage Tolerance Guaranteed Ω Dynamic Impedance Very Low Power Consumption APPLICATIO S Portable Meter References Portable
LTC Bit Rail-to-Rail Micropower DAC in MSOP Package FEATURES
12-Bit Rail-to-Rail Micropower DAC in MSOP Package FEATURES Buffered True Rail-to-Rail Voltage Output Maximum DNL Error:.5LSB 12-Bit Resolution Supply Operation: 3V to 5V Output Swings from V to V REF
DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. LT1004 Micropower Voltage Reference
LT Micropower Voltage eference FEATES Guaranteed ±mv Initial Accuracy LT-. Guaranteed ±mv Accuracy LT-.5 Guaranteed µa Operating Current Guaranteed Temperature Performance Operates up to ma Very Low Dynamic
LTC1798 Series Micropower Low Dropout References FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION
Micropower Low Dropout References FEATURES n mv Max Dropout at ma Output Current n µa Typical Quiescent Current n.% Max Initial Accuracy n No Output Capacitor Required n Output Sources ma, Sinks ma n ppm/
NCV1009ZG. 2.5 Volt Reference
V9 2.5 Volt Reference The V9 is a precision trimmed 2.5 V ±5. mv shunt regulator diode. The low dynamic impedance and wide operating current range enhances its versatility. The tight reference tolerance
Distributed by: www.jameco.com -8-83-4242 The content and copyrights of the attached material are the property of its owner. FEATRES Regulates While Sourcing or Sinking Current Provides Termination for
FEATURES U U PRECO DITIO I G APPLICATIO S TYPICAL APPLICATIO. LT1033 3A Negative Adjustable Regulator DESCRIPTIO
NOT RECOMMENDED FOR NEW DESIGNS Contact Linear Technology for Potential Replacement FEATRES Guaranteed 1% Initial Voltage Tolerance Guaranteed.15%/V Line Regulation Guaranteed.2%/ W Thermal Regulation
DATASHEET ICL8069. Features. Pinouts. Ordering Information. Low Voltage Reference. FN3172 Rev.3.00 Page 1 of 6. Jan FN3172 Rev.3.00.
DATASHEET Low Voltage Reference The is a 1.2V temperature-compensated voltage reference. It uses the band-gap principle to achieve excellent stability and low noise at reverse currents down to 50 A. Applications
LT MHz, 30V/µs 16-Bit Accurate A V 2 Op Amp. Description. Features. Applications. Typical Application
Features n Stable in Gain A (A = ) n MHz Gain Bandwidth Product n /μs Slew Rate n Settling Time: 8ns ( Step, ) n Specified at and Supplies n Low Distortion, 9.dB for khz, P-P n Maximum Input Offset oltage:
FEATURES TYPICAL APPLICATIO. LT1194 Video Difference Amplifier DESCRIPTIO APPLICATIO S
FEATURES Differential or Single-Ended Gain Block: ± (db) db Bandwidth: MHz Slew Rate: /µs Low Cost Output Current: ±ma Settling Time: ns to.% CMRR at MHz: db Differential Gain Error:.% Differential Phase
LT Dual 200MHz, 30V/µs 16-Bit Accurate A V 2 Op Amp DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION
FEATURES n Stable in Gain A (A = ) n MHz Gain Bandwidth Product n /μs Slew Rate n Settling Time: 8ns (μ, Step) n Specifi ed at and Supplies n Maximum Input Offset oltage: μ n Low Distortion: 9. for khz,
DESCRIPTIO APPLICATIO S TYPICAL APPLICATIO LTC1921 Dual 48V Supply and Fuse Monitor FEATURES
LTC9 Dual Supply and Fuse Monitor FEATRES Withstands Transient Voltages p to V/V Requires No Precision External Components Independently Monitors Two Supplies for ndervoltage Faults:.V ±V MAX Overvoltage
DESCRIPTIO FEATURES APPLICATIO S. LT GHz to 2.7GHz Receiver Front End TYPICAL APPLICATIO
1.GHz to 2.GHz Receiver Front End FEATURES 1.V to 5.25V Supply Dual LNA Gain Setting: +13.5dB/ db at Double-Balanced Mixer Internal LO Buffer LNA Input Internally Matched Low Supply Current: 23mA Low Shutdown
TYPICAL APPLICATIO. LT1027 Precision 5V Reference FEATURES DESCRIPTIO APPLICATIO S
Precision 5V Reference FEATRES Very Low Drift: 2ppm/ C Max TC Pin Compatible with LT121-5, REF-2, (PDIP Package) Output Sources 15mA, Sinks 1mA Excellent Transient Response Suitable for A-to-D Reference
Distributed by: www.jameco.com --3-44 The content and copyrights of the attached material are the property of its owner. MHz, 3nV/ Hz, A V Operational Amplifier FEATRES Gain-Bandwidth: MHz Gain of Stable
SC431M. Adjustable Shunt Regulator. Description. Features. Applications. Typical Application Circuit
SC431M Adjustable Shunt Regulator Features Wide operating current range 130µA to 150mA Low dynamic output impedance 0.25Ω typ. Trimmed bandgap + 0.5% Alternate for TL1431, TL431, LM431& AS431 Military
FEATURES TYPICAL APPLICATIO LTC MHz to 3GHz RF Power Detector. in SC70 Package DESCRIPTIO APPLICATIO S
300MHz to 3GHz RF Power Detector in SC70 Package FEATRES Temperature Compensated Internal Schottky Diode RF Detector Wide Input Frequency Range: 300MHz to 3GHz Wide Input Power Range: 30dBm to 6dBm Buffered
FEATURES APPLICATIONS TYPICAL APPLICATION LT1466L/LT1467L Micropower Dual/Quad Precision Rail-to-Rail Input and Output Op Amps
Micropower Dual/Quad Precision Rail-to-Rail Input and Output Op Amps FEATRES Rail-to-Rail Input and Output Low Supply Current: 75µA Max 39µV V OS(MAX) for V CM = V to V + High Common Mode Rejection Ratio:
LT1206 TA mA/60MHz Current Feedback Amplifi er DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION
LT26 2mA/6MHz Current Feedback Amplifi er FEATURES 2mA Minimum Output Drive Current 6MHz Bandwidth, A V = 2, R L = Ω 9V/µs Slew Rate, A V = 2, R L = Ω.2% Differential Gain, A V = 2, R L = Ω.7 Differential
TYPICAL APPLICATIO. LT MHz, 250V/µs, A V 4 Operational Amplifier DESCRIPTIO FEATURES APPLICATIO S
5MHz, 5V/µs, A V Operational Amplifier FEATRES Gain-Bandwidth: 5MHz Gain of Stable Slew Rate: 5V/µs Input Noise Voltage: nv/ Hz C-Load TM Op Amp Drives Capacitive Loads Maximum Input Offset Voltage: µv
LTC1664 Micropower Quad 10-Bit DAC. Applications. Block Diagram
LTC Micropower Quad -Bit DAC Features n Tiny: DACs in the Board Space of an SO- n Micropower: µa per DAC Plus µa Sleep Mode for Extended Battery Life n Wide.V to.v Supply Range n Rail-to-Rail Voltage Outputs
1.2 V Precision Low Noise Shunt Voltage Reference ADR512
1.2 V Precision Low Noise Shunt Voltage Reference FEATURES Precision 1.200 V Voltage Reference Ultracompact 3 mm 3 mm SOT-23 Package No External Capacitor Required Low Output Noise: 4 V p-p (0.1 Hz to
DESCRIPTIO FEATURES LT1787/LT1787HV Precision, High Side Current Sense Amplifiers APPLICATIO S TYPICAL APPLICATIO
Precision, High Side Current Sense Amplifiers FEATURES Input Offset Voltage: µv (Max) upply Operation (LTHV) -Bit Dynamic Range Operating Current: µa User-Selectable External Sense Resistor Bidirectional
HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8
HA-533 Data Sheet February 6, 26 FN2924.8 25MHz Video Buffer The HA-533 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 25MHz and
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
Precision, Low Power, Micropower Dual Operational Amplifier OP290
Precision, Low Power, Micropower Dual Operational Amplifier OP9 FEATURES Single-/dual-supply operation:. V to 3 V, ±.8 V to ±8 V True single-supply operation; input and output voltage Input/output ranges
DESCRIPTIO APPLICATIO S. LTC5531 Precision 300MHz to 7GHz RF Detector with Shutdown and Offset Adjustment FEATURES TYPICAL APPLICATIO
LTC553 Precision 3MHz to 7GHz RF Detector with Shutdown and Offset Adjustment FEATURES Temperature Compensated Internal Schottky Diode RF Detector Wide Input Frequency Range: 3MHz to 7GHz* Wide Input Power
TS V adjustable shunt voltage reference. Description. Features. Applications
1.24 V adjustable shunt voltage reference Datasheet - production data Battery chargers Switch mode power supply Battery operated equipment SOT23-3L (Plastic micropackage) Description The is an adjustable
LTC1440/LTC1441/LTC1442 Ultralow Power Single/Dual Comparator with Reference DESCRIPTIO FEATURES APPLICATIO S TYPICAL APPLICATIO
LTC/LTC/LTC Ultralow Power Single/Dual Comparator with Reference FEATURES Ultralow Quiescent Current:.µA Typ (LTC) Reference Output Drives.µF Capacitor Adjustable Hysteresis (LTC/LTC) Wide Supply Range:
FEATURES DESCRIPTIO APPLICATIO S. LT1120 Micropower Regulator with Comparator and Shutdown TYPICAL APPLICATIO
LT Micropower Regulator with Comparator and Shutdown FEATRES μa Supply Current ma Output Current.V Reference Voltage Reference Output Sources ma and Sinks ma Open Collector Comparator Sinks ma Logic Shutdown.V
FEATURES DESCRIPTIO APPLICATIO S TYPICAL APPLICATIO. LTC1046 Inductorless 5V to 5V Converter
LTC Inductorless V to V Converter FEATRES ma Output Current Plug-In Compatible with ICL/LTC R OT = Ω Maximum µa Maximum No Load Supply Current at V Boost Pin (Pin ) for Higher Switching Frequency 9% Minimum
V ON = 0.93V V OFF = 0.91V V ON = 2.79V V OFF = 2.73V V ON = 4.21V V OFF = 3.76V V ON = 3.32V V OFF = 2.80V. 45.3k 6.04k 1.62k. 3.09k. 7.68k 1.
FEATURES Fully Sequence Four Supplies Six with Minimal External Circuitry Cascadable for Additional Supplies Power Off in Reverse Order or Simultaneously Charge Pump Drives External MOSFETs Drives Power
DESCRIPTIO FEATURES APPLICATIO S. LT1129/LT /LT Micropower Low Dropout Regulators with Shutdown TYPICAL APPLICATIO
Micropower Low Dropout Regulators with Shutdown FEATRES.4V Dropout Voltage 7mA Output Current µa Quiescent Current No Protection Diodes Needed Adjustable Output from 3.8V to 3V 3.3V and V Fixed Output
FEATURES TYPICAL APPLICATIO. LT µA, 14nV/ Hz, Rail-to-Rail Output Precision Op Amp with Shutdown DESCRIPTIO APPLICATIO S
FEATURES 3µV Maximum Offset Voltage pa Maximum Input Bias Current 3µA Supply Current Rail-to-Rail Output Swing µa Supply Current in Shutdown db Minimum Voltage Gain (V S = ±V).µV/ C Maximum V OS Drift
HA Features. 12MHz, High Input Impedance, Operational Amplifier. Applications. Pinout. Part Number Information. Data Sheet May 2003 FN2893.
OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 HA-2515 Data Sheet May 23 FN2893.5 12MHz, High Input Impedance, Operational Amplifier HA-2515 is a high performance operational amplifier which sets
DESCRIPTIO APPLICATIO S. LTC5530 Precision 300MHz to 7GHz RF Detector with Shutdown and Gain Adjustment FEATURES TYPICAL APPLICATIO
Precision 3MHz to 7GHz RF Detector with Shutdown and Gain Adjustment FEATURES Temperature Compensated Internal Schottky Diode RF Detector Wide Input Frequency Range: 3MHz to 7GHz* Wide Input Power Range:
FEATURES DESCRIPTIO APPLICATIO S TYPICAL APPLICATIO. LT1024 Dual, Matched Picoampere, Microvolt Input, Low Noise Op Amp
FEATURES Guaranteed Offset Voltage: 5µV Max Guaranteed Bias Current: 5 C: pa Max 55 C to 5 C: 7pA Max Guaranteed Drift:.5µV/ C Max Low Noise,.Hz to Hz:.5µV P-P Guaranteed Supply Current: 6µA Max Guaranteed
VID Controlled High Current 4-Phase DC/DC Converter (Simplified Block Diagram) 4.5V TO 22V V OS TG1 INTV CC SW1 LTC1629 BG1 PGND SGND TG2 EAIN SW2
FEATRES Fully Compliant with the Intel RM 8. ID Specification Programs Regulator Output oltage from.0 to.8 in m Steps Programs an Entire Family of Linear Technology DC/DC Converters with 0.8 References
FEATURES APPLICATIONS TYPICAL APPLICATION. LTC1451 LTC1452/LTC Bit Rail-to-Rail Micropower DACs in SO-8 DESCRIPTION
12-Bit Rail-to-Rail Micropower DACs in SO-8 FEATRES 12-Bit Resolution Buffered True Rail-to-Rail Voltage Output 3V Operation (LTC1453), I CC : 250µA Typ 5V Operation (), I CC : 400µA Typ 3V to 5V Operation
DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. LT1498/LT MHz, 6V/µs, Dual/Quad Rail-to-Rail Input and Output Precision C-Load Op Amps
MHz, 6V/µs, Dual/Quad Rail-to-Rail Input and Output Precision C-Load Op Amps FEATRES Rail-to-Rail Input and Output 475µV Max V OS from V + to V Gain-Bandwidth Product: MHz Slew Rate: 6V/µs Low Supply Current
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628 FEATURES FUNCTIONAL BLOCK DIAGRAM High common-mode input voltage range ±20 V at VS = ±5 V Gain range 0. to 00 Operating temperature
DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. LT1039A/LT1039A-16 Triple RS232 Driver/Receiver with Shutdown
FEATRES On-Chip ESD Protection: ±15kV Human Body Model ±15kV IEC-00-4-2 Air Gap Test** ±8kV IEC-00-4-2 Contact Test 125kBd Operation with 3kΩ/2500pF Load 250kBd Operation with 3kΩ/00pF Load Operates from
DESCRIPTIO. LT685 High Speed Comparator FEATURES APPLICATIO S TYPICAL APPLICATIO
High Speed Comparator FEATRES ltrafast (5.5ns typ) Complementary ECL Output 50Ω Line Driving Capability Low Offset Voltage Output Latch Capability External Hysteresis Control Pin Compatible with Am685
1.2 V Precision Low Noise Shunt Voltage Reference ADR512W
1.2 V Precision Low Noise Shunt Voltage Reference ADR512W FEATURES Precision 1.200 V voltage reference Ultracompact 3-lead SOT-23 package No external capacitor required Low output noise: 4 µv p-p (0.1
V ON = 2.64V V OFF = 1.98V V ON = 0.93V V OFF = 0.915V V ON = 3.97V V OFF = 2.97V. V ON = 2.79V V OFF = 2.73V 100k 1.62k 66.5k. 6.04k.
FEATURES Fully Sequence and Monitor Four Supplies Six with Minimal External Circuitry Cascadable for Additional Supplies Power Off in Reverse Order or Simultaneously Charge Pump Drives External MOSFETs
FEATURES DESCRIPTIO APPLICATIO S LTC1451 LTC1452/LTC Bit Rail-to-Rail Micropower DACs in SO-8 TYPICAL APPLICATIO
12-Bit Rail-to-Rail Micropower DACs in SO-8 FEATRES 12-Bit Resolution Buffered True Rail-to-Rail Voltage Output 3V Operation (LTC1453), I CC : 250µA Typ 5V Operation (), I CC : 400µA Typ 3V to 5V Operation
FEATURES APPLICATIO S TYPICAL APPLICATIO. LT1102 High Speed, Precision, JFET Input Instrumentation Amplifier (Fixed Gain = 10 or 100) DESCRIPTIO
FEATRES Slew Rate: V/μs Gain-Bandwidth Product: MHz Settling Time (.%): μs Overdrive Recovery:.μs Gain Error:.% Max Gain Drift: ppm/ C Gain Nonlinearity: ppm Max Offset Voltage (Input Output): μv Max Drift
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM136-2.5/LM236-2.5/LM336-2.5V Reference Diode General Description The LM136-2.5/LM236-2.5
DATASHEET CA Applications. Pinout. Ordering Information. General Purpose NPN Transistor Array. FN483 Rev.6.00 Page 1 of 7.
DATASHEET CA-386 General Purpose NPN Transistor Array The CA386 consists of five general-purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected
TS HIGH THERMAL STABILITY MICROPOWER SHUNT VOLTAGE REFERENCE
HIGH THERMAL STABILITY MICROPOWER SHUNT VOLTAGE REFERENCE LOW Tc: ppm/ C MAXIMUM.V OUTPUT VOLTAGE LOW OPERATING CURRENT: 6µA max @ C HIGH PRECISION AT C: ±.% AND ±% STABLE WHEN USED WITH CAPACITIVE LOADS
AMS A Adjustable/Fixed Low Dropout Linear Regulator. General Description. Key Features. Applications. Typical Application
General Description The -ADJ and -1.2,-1.5,-1.8,-2.5,-2.85, -3.3 and-5 are low dropout three-terminal regulators with 1A output current capability. These devices have been optimized for low voltage where
September 2010 Rev FEATURES. Fig. 1: XRP431L Application Diagram
September 2010 Rev. 1.2.0 GENERAL DESCRIPTION The XRP431L is a three-terminal adjustable shunt voltage regulator providing a highly accurate bandgap reference. The XRP431L acts as an open-loop error amplifier
DESCRIPTIO TYPICAL APPLICATIO. LTC1383 5V Low Power RS232 Transceiver FEATURES APPLICATIO S
LTC V Low Power RS Transceiver FEATRES Operates from a Single V Supply Low Supply Current: I CC = µa ESD Protection Over ±kv Available in -Pin SOIC Narrow Package ses Small Capacitors: Operates to kbaud
HA-2520, HA-2522, HA-2525
HA-, HA-, HA- Data Sheet November, 6 FN894.8 MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-, HA-, HA- comprise a series of operational amplifiers delivering an unsurpassed
DESCRIPTIO TYPICAL APPLICATIO. LT1803/LT1804/LT1805 Single/Dual/Quad 100V/µs, 85MHz, Rail-to-Rail Input and Output Op Amps FEATURES APPLICATIO S
FEATURES Slew Rate: V/µs Gain Bandwidth Product: 8MHz Input Common Mode Range Includes Both Rails Output Swings Rail-to-Rail Low Quiescent Current: 3mA Max per Amplifier Large Output Current: 42mA Voltage
1.0 V Precision Low Noise Shunt Voltage Reference ADR510
1.0 V Precision Low Noise Shunt Voltage Reference FEATURES Precision 1.000 V voltage reference Ultracompact 3 mm 3 mm SOT-23 package No external capacitor required Low output noise: 4 μv p-p (0.1 Hz to
Dual Low Offset, Low Power Operational Amplifier OP200
Dual Low Offset, Low Power Operational Amplifier OP200 FEATURES Low input offset voltage: 75 μv maximum Low offset voltage drift, over 55 C < TA < +25 C 0.5 μv/ C maximum Low supply current (per amplifier):
Low Noise, Micropower 5.0 V Precision Voltage Reference ADR293-EP
Enhanced Product Low Noise, Micropower 5.0 V Precision Voltage Reference FEATURES 6.0 V to 15 V supply range Supply current: 15 μa maximum Low noise: 15 μv p-p typical (0.1 Hz to 10 Hz) High output current:
CA124, CA224, CA324, LM324, LM2902
OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT CA, CA, CA, LM, LM9 Data Sheet May File Number 796.5 itle 9 b- ad, Hz, raal plis i- - -, usl, lis) tho y- ds er- Quad, MHz, Operational Amplifiers for Commercial,
FEATURES TYPICAL APPLICATIO. LTC1382 5V Low Power RS232 Transceiver with Shutdown DESCRIPTIO APPLICATIO S
FEATRES Operates from a Single V Supply Low Supply Current: I CC = µa I CC =.µa in Shutdown Mode ESD Protection Over ±1kV ses Small Capacitors:.1µF Operates to 1kBaud Output Overvoltage Does Not Force
DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12.
25MHz Video Buffer NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at -888-INTERSIL or www.intersil.com/tsc DATASHEET FN2924 Rev 8. The HA-533 is a unity
RH1016M UltraFast Precision 10ns Comparator ABSOLUTE MAXIMUM RATINGS DESCRIPTION BURN-IN CIRCUIT PACKAGE INFORMATION
DESCRIPTION The RH is an UltraFast TM ns comparator that interfaces directly to TTL/CMOS logic while operating from either ±V or single V supplies. Tight offset voltage specifi ca tions and high gain allow
DATASHEET HA Features. Applications. Ordering Information. 110MHz, High Slew Rate, High Output Current Buffer. FN2921 Rev 12.
DATASHEET HA-52 MHz, High Slew Rate, High Output Current Buffer The HA-52 is a monolithic, wideband, high slew rate, high output current, buffer amplifier. Utilizing the advantages of the Intersil D.I.
1.2 V Precision Low Noise Shunt Voltage Reference ADR512
FEATURES Precision 1.200 V Voltage Reference Ultracompact 3 mm 3 mm SOT-23 Package No External Capacitor Required Low Output Noise: 4 µv p-p (0.1 Hz to 10 Hz) Initial Accuracy: ±0.3% Max Temperature Coefficient:
RC A Adjustable/Fixed Low Dropout Linear Regulator. Description. Features. Applications. Typical Applications.
www.fairchildsemi.com A Adjustable/Fixed Low Dropout Linear Regulator Features Low dropout voltage Load regulation:.5% typical Trimmed current limit On-chip thermal limiting Standard SOT-223, TO-263, and
LT1011/LT1011A Voltage Comparator FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION
LT/LTA Voltage Comparator FEATURES n Pin Compatible with LM Series Devices n Guaranteed Max.mV Input Offset Voltage n Guaranteed Max na Input Bias Current n Guaranteed Max na Input Offset Current n Guaranteed
Dual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature
Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by
FEATURES DESCRIPTIO APPLICATIO S. LTC2050/LTC2050HV Zero-Drift Operational Amplifiers in SOT-23 TYPICAL APPLICATION
FEATRES Maximum Offset Voltage of µv Maximum Offset Voltage Drift of nv/ C Noise:.µV P-P (.Hz to Hz Typ) Voltage Gain: db (Typ) PSRR: db (Typ) CMRR: db (Typ) Supply Current:.8mA (Typ) Supply Operation:.7V
LTC mA Step-Up DC/DC Converter with Maximum Power Point Control and 250mV Start-Up APPLICATIONS TYPICAL APPLICATION
400mA Step-Up DC/DC Converter with Maximum Power Point Control and 250mV Start-Up FEATURES n Low Start-Up Voltage: 250mV n Maximum Power Point Control n Wide Range: 225mV to 5V n Auxiliary 6mA Regulator
150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS
ICS NETWORKING AND PCI CLOCK SOURCE. Description. Features. Block Diagram DATASHEET
DATASHEET Description The is a low cost frequency generator designed to support networking and PCI applications. Using analog/digital Phase Locked-Loop (PLL) techniques, the device uses a standard fundamental
FEATURES TYPICAL APPLICATIO. LT1635 Micropower Rail-to-Rail Op Amp and Reference DESCRIPTIO APPLICATIO S
LT5 Micropower Rail-to-Rail Op Amp and Reference FEATRES Guaranteed Operation at.v Op Amp and Reference on Single Chip Micropower: µa Supply Current Industrial Temperature Range SO- Packages Rail-to-Rail
DESCRIPTIO. LTC1446/LTC1446L Dual 12-Bit Rail-to-Rail Micropower DACs in SO-8
Dual 12-Bit Rail-to-Rail Micropower DACs in SO-8 FEATRES Dual DACs with 12-Bit Resolution SO-8 Package Rail-to-Rail Output Amplifiers 3V Operation (LTC1446L): I CC = 65µA Typ 5V Operation (LTC1446): I
APPLICATIO S BLOCK DIAGRA. LTC2602/LTC2612/LTC2622 Dual 16-/14-/12-Bit Rail-to-Rail DACs in 8-Lead MSOP FEATURES DESCRIPTIO
LTC262/LTC2612/LTC2622 Dual 16-/14-/12-Bit Rail-to-Rail DACs in 8-Lead MSOP FEATURES Smallest Pin-Compatible Dual DACs: LTC262: 16-Bits LTC2612: 14-Bits LTC2622: 12-Bits Guaranteed 16-Bit Monotonic Over
LTC4352 Low Voltage Ideal Diode Controller with Monitoring FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION
Low Voltage Ideal Diode Controller with Monitoring FEATURES n Low Loss Replacement for Power Diode n Controls N-Channel MOSFET n V to 18V Supply ORing or Holdup n.μs Turn-On and Turn-Off Time n Undervoltage
FEATURES DESCRIPTIO APPLICATIO S. LT1636 Over-The-Top Micropower Rail-to-Rail Input and Output Op Amp TYPICAL APPLICATIO
Over-The-Top Micropower Rail-to-Rail Input and Output Op Amp FEATRES Rail-to-Rail Input and Output Micropower: 5µA I Q, 44V Supply MSOP Package Over-The-Top TM : Input Common Mode Range Extends 44V Above
AME. Shunt Bandgap Voltage Reference. General Description. Functional Block Diagram. Features. Typical Application. Applications
General Description The is a micropower 2-terminal band-gap voltage regulator diode. It operates over a 30µA to 20mA current range. Each circuit is trimmed at wafer sort to provide a ± 0.5% initial tolerance.
ABSOLTE MAXIMM RATINGS W W W... 7V Operating Junction Temperature Range Control Section... 0 C to 125 C Power Transistor... 0 C to 150 C Storage Tempe
FEATRES Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation: 0.05% Typ Trimmed Current Limit On-Chip Thermal Limiting APPLICATIONS Intel Pentium Pro Processor GTL Supply
MCP1700. Low Quiescent Current LDO. General Description. Features. Applications. Package Types. Related Literature. 3-Pin TO-92
Low Quiescent Current LDO Features 1.6 µa Typical Quiescent Current Input Operating Voltage Range: 2.3V to 6.0V Output Voltage Range: 1.2V to 5.0V 250 ma Output Current for output voltages 2.5V 200 ma
HA MHz Video Buffer. Description. Features. Applications. Ordering Information. Pinouts. April 1997
SEMICONDUCTOR HA-533 April 997 25MHz Video Buffer Features Differential Phase Error...............2 Degrees Differential Gain Error......................3% High Slew Rate......................... /µs Wide
VIN VOUT + + GND SHDN AIC1731. Low Noise Low Dropout Linear Regulator
300mA, Low Dropout Linear Regulator with Shutdown FEATURES Active Low Shutdown Control. Very Low Quiescent Current. Very Low Dropout Voltage of 470mV at 300mA Output Current (3.0V Output Version) 1.3V,
Wideband, High Output Current, Fast Settling Op Amp AD842
a FEATURES AC PERFORMAE Gain Bandwidth Product: 8 MHz (Gain = 2) Fast Settling: ns to.1% for a V Step Slew Rate: 375 V/ s Stable at Gains of 2 or Greater Full Power Bandwidth: 6. MHz for V p-p DC PERFORMAE
LT3572 Dual Full-Bridge Piezo Driver with 900mA Boost Converter DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION
Dual Full-Bridge Piezo Driver with 900mA Boost Converter FEATURES 2.7V to 0V Input Voltage Range 900mA Boost Converter Dual Full-Bridge Piezo Drivers Up to 00kHz PWM Frequency Programmable Switching Frequency
APPLICATIO S TYPICAL APPLICATIO. LTC2051/LTC2052 Dual/Quad Zero-Drift Operational Amplifiers FEATURES DESCRIPTIO
LTC/LTC Dual/Quad Zero-Drift Operational Amplifiers FEATRES Maximum Offset Voltage of μv Maximum Offset Voltage Drift of nv/ C Small Footprint, Low Profile MS/GN Packages Single Supply Operation:.V to
DATASHEET HA Features. Applications. Pinout. Part Number Information. 12MHz, High Input Impedance, Operational Amplifier
12MHz, High Input Impedance, Operational Amplifier OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 DATASHEET FN289 Rev 6. HA-255 is an operational amplifier whose design is optimized to deliver excellent
Low Noise, Micropower 5.0 V Precision Voltage Reference ADR293
Low Noise, Micropower 5. V Precision Voltage Reference ADR93 FEATURES. V to 5 V supply range Supply current: 5 μa maximum Low noise: 5 μv p-p typical (. Hz to Hz) High output current: 5 ma Temperature
LT GHz to 3.8GHz High Linearity Upconverting Mixer. Description. Features. Applications. Typical Application
Features n High Output IP3: +7.3 at.1ghz n Low Noise Floor: /Hz (P OUT = 5) n High Conversion Gain:. at.1ghz n Wide Frequency Range: 1.5GHz to 3.GHz* n Low LO Leakage n Single-Ended RF and LO n Low LO
LTC6081/LTC6082 Precision Dual/Quad CMOS Rail-to-Rail Input/ Output Amplifi ers DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION
FEATURES Maximum Offset Voltage: 7μV (2 C) Maximum Offset Drift:.8μV/ C Maximum Input Bias: pa (2 C) 4pA (T A 8 C) Open Loop Voltage Gain: 2dB Typ Gain Bandwidth Product: 3.6MHz CMRR: db Min PSRR: 98dB
MP A, 50V, 1.2MHz Step-Down Converter in a TSOT23-6
MP2456 0.5A, 50V, 1.2MHz Step-Down Converter in a TSOT23-6 DESCRIPTION The MP2456 is a monolithic, step-down, switchmode converter with a built-in power MOSFET. It achieves a 0.5A peak-output current over
Dual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
Features. QUIESCENT CURRENT (µa)
Enpirion Power Datasheet EY161SA-ADJ 4V, Low Quiescent Current, 5mA Linear Regulator for EY161SA-ADJ Datasheet The EY161SA-ADJ is a high voltage, low quiescent current linear regulator ideally suited for
MK2703 PLL AUDIO CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET MK2703 Description The MK2703 is a low-cost, low-jitter, high-performance PLL clock synthesizer designed to replace oscillators and PLL circuits in set-top box and multimedia systems. Using IDT
LTC2935 Ultra-Low Power Supervisor with Power-Fail Output, Selectable Thresholds FEATURES
Ultra-Low Power Supervisor with Power-Fail Output, Selectable Thresholds FEATURES n 5nA Quiescent Current n ±1.5% (Max) Accuracy over Temperature n Integrated Precision Attenuators n Eight Pin-Selectable
DESCRIPTIO FEATURES TYPICAL APPLICATIO. LT1080/LT1081 Advanced Low Power 5V RS232 Dual Driver/Receiver APPLICATIO S
Advanced Low Power V RS Dual Driver/Receiver FEATRES Superior to CMOS Improved Speed: Operates over kbaud Improved Protection: Outputs Can Be Forced to ±0V without Damage Three-State Outputs Are High Impedance
High Precision Shunt Mode Voltage References ADR525/ADR530/ADR550
High Precision Shunt Mode Voltage References ADR525/ADR530/ FEATURES Ultracompact SC70 and SOT-23-3 packages Temperature coefficient: 40 ppm/ C (maximum) 2 the temperature coefficient improvement over
TS6001. A 7ppm/ C, 0.08% Precision +2.5V Voltage Reference in SOT23 FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION CIRCUIT
VOLTAGE - Volt TS6001 A 7ppm/ C, 0.08% Precision +2.5V Voltage Reference in SOT23 FEATURES Improved Electrical Performance over MAX6025 Initial Accuracy: 0.08% (max) TS6001A 0.16% (max) TS6001B Temperature
1.2 V Micropower, Precision Shunt Voltage Reference AD1580
.2 V Micropower, Precision Shunt Voltage Reference AD58 FEATURES Wide operating range: 5 µa to ma Initial accuracy: ±.% maximum Temperature drift: ±5 ppm/ C maximum Output impedance:.5 Ω maximum Wideband
APPLICATIO S. LT /LT1585A-1.5 Fixed 1.5V, 4.6A and 5A Low Dropout, Fast Response GTL+ Regulators DESCRIPTIO FEATURES TYPICAL APPLICATIO
FEATRES Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation: 0.05% Typ Trimmed Current Limit On-Chip Thermal Limiting APPLICATIO S GTL+ Power Supply Low Voltage Logic
PCI-EXPRESS CLOCK SOURCE. Features
DATASHEET ICS557-01 Description The ICS557-01 is a clock chip designed for use in PCI-Express Cards as a clock source. It provides a pair of differential outputs at 100 MHz in a small 8-pin SOIC package.