SM5006 series Crystal Oscillator Module ICs

Transcription

1 Crystal Oscillator Module ICs OVERVIEW The SM5006 series are crystal oscillator module ICs, that incorporate high-frequency, low current consumption oscillator and output buffer circuits. Highly accurate thin-film feedback resistors and high-frequency capacitors are built-in, eliminating the need for external components to make a stable 3rd overtone oscillator. FEATURES Up to 107MHz operation Capacitors C G, C D built-in Inverter amplifier feedback resistor built-in TTL input level 16mA (V DD = 4.5V) drive capability 4mA (V DD = 4.5V) drive capability (5006AH ) SERIES CONFIGURATION Output three-state function 2.7 to 5.5V supply voltage Oscillator frequency output 8-pin SOP (SM5006 S) Chip form (CF5006 ) Version *1 3V operating 5V operating Built-in capacitance gm R f Input Output Output Recommended Output Recommended ratio [kω] level duty load operating load operating Output level (max) frequency (max) frequency waveform *3 C G C D [pf] range *2 [MHz] [pf] range *2 [MHz] t r /t f [ns] [pf] [pf] SM5006ANAS to 30 8/ TTL CMOS SM5006ANBS to 40 8/ TTL CMOS SM5006ANCS to to 60 7/ TTL CMOS SM5006ANDS to to 70 7/ TTL CMOS SM5006ANES to (15) *4 70 to 100 6/ TTL CMOS SM5006ANFS 4 30 (15) *4 80 to 107 6/ TTL CMOS SM5006CNCS to to to 50 8/ TTL CMOS SM5006CNDS to to 70 8/ TTL CMOS SM5006CNES to to 100 7/ TTL CMOS SM5006BNCS to to to 70 7/ No TTL CMOS SM5006BNES to (15) *4 70 to 107 6/ No TTL CMOS SM5006DNCS to to to 50 8/ No TTL CMOS SM5006DNES to to to 70 7/ No TTL CMOS SM5006AKAS to 30 4/ TTL TTL SM5006AKBS to 40 4/ TTL TTL SM5006AKCS to 60 4/ TTL TTL SM5006AKDS to 70 4/ TTL TTL SM5006CKDS to 70 4/ TTL TTL SM5006BKCS to 70 4/ No TTL TTL SM5006DKCS to 70 4/ No TTL TTL SM5006AHAS to 30 7/ TTL CMOS SM5006AHBS to 40 7/ TTL CMOS SM5006AHCS to 60 7/ TTL CMOS SM5006AHDS to 70 7/ TTL CMOS *1. Chip form devices have designation CF5006. *2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. * N : C L = 50pF, CMOS load, 5006 K :, 10TTL load, 5006AH :, CMOS load *4. SOP package only SEIKO NPC CORPORATION 1

2 ORDERING INFORMATION Device SM5006 S CF Package 8-pin SOP Chip form PACKAGE DIMENSIONS (: mm) 8-pin SOP typ M 0 to 10 SEIKO NPC CORPORATION 2

3 PAD LAYOUT (: µm) PINOUT (Top view) Q (920,1310) Y HA5006 INHN 1 8 XT 2 7 NC XTN 3 6 NC (0,0) INHN XT XTN VSS VSS 4 5 Q X Chip size: mm Chip thickness: 300 ± 30µm Chip base: V DD level PIN DESCRIPTION and PAD DIMENSIONS Pad dimensions [µm] Number Name I/O Description X Y 1 INHN I Output state control input. High impedance when LOW. Pull-up resistor built in XT I Amplifier input. Crystal oscillator connection pins XTN O Amplifier output. Crystal oscillator connected between XT and XTN VSS Ground Q O Output. Output frequency (f O ) NC No connection 7 NC No connection 8 Supply voltage BLOCK DIAGRAM VSS XTN RG CG Rf RD CD XT Q INHN SEIKO NPC CORPORATION 3

4 SPECIFICATIONS Absolute Maximum s V SS = 0V Parameter Symbol Condition Supply voltage range V DD 0.5 to 7.0 V Input voltage range V IN 0.5 to V DD V Output voltage range V OUT 0.5 to V DD V Operating temperature range T opr 40 to 85 Storage temperature range T stg Chip form 8-pin SOP 65 to to 125 Output current I OUT 5006 N, K AH 10 ma Power dissipation P D 8-pin SOP 500 mw SEIKO NPC CORPORATION 4

5 Recommended Operating Conditions SM5006 series (package form) V SS = 0V Parameter Symbol Series Condition Supply voltage V DD ANA, ANB, CNC, CND, DNC ANC, AND, BNC, CNE, DNE ANE, ANF, BNE f 50MHz, C L = 50pF f 70MHz, f 40MHz, f 70MHz, C L = 50pF f 100MHz, f 50MHz, f 70MHz, f 100MHz, f 107MHz, f 50MHz, f 70MHz, V V V AKA, AKB, AKC, CKD, DKC f 70MHz, V AKD, BKC f 70MHz, V AHA, AHB, AHC, AHD f 70MHz, V Input voltage V IN All series V SS V DD V ANA, ANB, CNC, CND, DNC ANC, AND, BNC, CNE, DNE f 50MHz, C L = 50pF, 4.5 V DD f 70MHz,, 4.5 V DD f 40MHz,, 2.7 V DD f 50MHz, C L = 50pF, 4.5 V DD f 70MHz, C L = 50pF, 4.5 V DD f 70MHz,, 4.5 V DD f 100MHz,, 4.5 V DD f 50MHz,, 2.7 V DD f 70MHz,, 3.0 V DD Operating temperature T OPR f 70MHz, C L = 50pF, 4.5 V DD f 100MHz,, 4.5 V DD ANE, ANF, BNE AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD f 107MHz,, 4.5 V DD f 50MHz,, 2.7 V DD f 70MHz,, 3.0 V DD f 50MHz,, 4.5 V DD f 70MHz,, 4.5 V DD f 50MHz,, 4.5 V DD f 70MHz,, 4.5 V DD f 50MHz,, 4.5 V DD f 70MHz,, 4.5 V DD SEIKO NPC CORPORATION 5

6 CF5006 series (chip form) V SS = 0V Parameter Symbol Series Condition ANA, ANB, CNC, CND, DNC f 50MHz, C L = 50pF f 70MHz, f 40MHz, V f 70MHz, C L = 50pF ANC, AND, BNC, CNE, DNE f 100MHz, f 50MHz, V f 70MHz, Supply voltage V DD f 70MHz, C L = 50pF ANE, ANF, BNE f 107MHz, C L = 30pF f 50MHz, V f 70MHz, AKA, AKB, AKC, CKD, DKC f 70MHz, V AKD, BKC f 70MHz, V AHA, AHB, AHC, AHD f 70MHz, V Input voltage V IN All series V SS V DD V ANA, ANB, CNC, CND, DNC f 50MHz, C L = 50pF, 4.5 V DD f 70MHz,, 4.5 V DD f 40MHz,, 2.7 V DD f 70MHz, C L = 50pF, 4.5 V DD ANC, AND, BNC, CNE, DNE f 100MHz,, 4.5 V DD f 50MHz,, 2.7 V DD f 70MHz,, 3.0 V DD f 70MHz, C L = 50pF, 4.5 V DD Operating temperature T OPR ANE, ANF, BNE f 100MHz, C L = 30pF, 4.5 V DD f 107MHz, C L = 30pF, 4.5 V DD f 50MHz,, 2.7 V DD f 70MHz,, 3.0 V DD AKA, AKB, AKC, CKD, DKC f 50MHz,, 4.5 V DD f 70MHz,, 4.5 V DD AKD, BKC f 50MHz,, 4.5 V DD f 70MHz,, 4.5 V DD AHA, AHB, AHC, AHD f 50MHz,, 4.5 V DD f 70MHz,, 4.5 V DD SEIKO NPC CORPORATION 6

7 Electrical Characteristics 5006 N series 3V operation: V DD = 2.7 to 3.6 V, V SS = 0 V, Ta = 20 to 80 unless otherwise noted. Parameter Symbol Condition HIGH-level output voltage V OH Q: Measurement cct 1, V DD = 2.7V, I OH = 8mA V LOW-level output voltage V OL Q: Measurement cct 2, V DD = 2.7V, I OL = 8mA V Output leakage current I Z Q: Measurement cct 2, INHN = LOW, V DD = 5.5V V OH = V DD 10 V OL = V SS 10 µa HIGH-level input voltage V IH INHN 2.0 V LOW-level input voltage V IL INHN 0.5 V f = 30MHz SM5006ANCS CF5006ANC SM5006BNCS CF5006BNC 8 16 f = 30MHz, Ta = 10 to 70 SM5006CNCS CF5006CNC 8 16 f = 50MHz SM5006ANDS CF5006AND Current consumption I DD INHN = open, V DD = 3.0 to 3.6V, f = 70MHz SM5006BNES CF5006BNE SM5006CNES CF5006CNE SM5006DNES CF5006DNE ma f = 40MHz, Ta = 10 to 70 SM5006CNDS CF5006CND SM5006DNCS CF5006DNC f = 70MHz SM5006ANES CF5006ANE SM5006ANFS CF5006ANF INHN pull-up resistance R UP Measurement cct kω SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB Feedback resistance R f Measurement cct 5 SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE kω Built-in resistance Built-in capacitance R G Design value, determined by the R f value R D Design value, determined by the R f value C G Design value. A monitor pattern on a wafer is tested C D Design value. A monitor pattern on a wafer is tested Ω pf SEIKO NPC CORPORATION 7

8 5V operation: V DD = 4.5 to 5.5V, V SS = 0V, Ta = 40 to 85 unless otherwise noted. Parameter Symbol Condition HIGH-level output voltage V OH Q: Measurement cct 1, V DD = 4.5V, I OH = 16mA V LOW-level output voltage V OL Q: Measurement cct 2, V DD = 4.5V, I OL = 16mA V Output leakage current I Z Q: Measurement cct 2, INHN = LOW, V DD = 5.5V V OH = V DD 10 V OL = V SS 10 µa HIGH-level input voltage V IH INHN 2.0 V LOW-level input voltage V IL INHN 0.8 V f = 30MHz SM5006ANAS CF5006ANA Current consumption I DD INHN = open, V DD = 4.5 to 5.5V, C L = 50pF INHN = open, V DD = 4.5 to 5.5V f = 40MHz SM5006ANBS CF5006ANB f = 60MHz CF5006ANC f = 60MHz, Ta = 20 to 80 SM5006ANCS f = 70MHz Ta = 20 to 80 f = 60MHz,, Ta = 15 to 75 f = 60MHz,, Ta = 0 to 70, Ta = 15 to 75, Ta = 0 to 70 f = 100MHz,, Ta = 20 to 80 f = 100MHz,, Ta = 0 to 70 CF5006AND CF5006BNC SM5006ANDS SM5006BNCS CF5006CNC SM5006CNCS CF5006CND CF5006DNC SM5006CNDS SM5006DNCS CF5006CNE CF5006DNE SM5006CNES SM5006DNES f = 100MHz, C L = 30pF CF5006ANE f = 100MHz, SM5006ANES f = 107MHz, C L = 30pF, Ta = 20 to 80 f = 107MHz,, Ta = 20 to 80 CF5006ANF CF5006BNE SM5006ANFS SM5006BNES INHN pull-up resistance R UP Measurement cct kω Feedback resistance R f Measurement cct 5 Built-in resistance Built-in capacitance SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE R G Design value, determined by the R f value R D Design value, determined by the R f value C G Design value. A monitor pattern on a wafer is tested C D Design value. A monitor pattern on a wafer is tested ma kω Ω pf SEIKO NPC CORPORATION 8

9 5006 K series V DD = 4.5 to 5.5V, V SS = 0V, Ta = 40 to 85 unless otherwise noted. Parameter Symbol Condition HIGH-level output voltage V OH V DD = 4.5V, Q: Measurement cct 1, I OH = 16mA SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB SM5006AKCS, CF5006AKC SM5006CKDS, CF5006CKD SM5006DKCS, CF5006DKC SM5006AKDS, CF5006AKD SM5006BKCS, CF5006BKC V LOW-level output voltage V OL Q: Measurement cct 2, V DD = 4.5V, I OL = 16mA V Output leakage current I Z Q: Measurement cct 2, INHN = LOW, V DD = 5.5V V OH = V DD 10 V OL = V SS 10 µa HIGH-level input voltage V IH INHN 2.0 V LOW-level input voltage V IL INHN 0.8 V f = 30MHz SM5006AKAS CF5006AKA f = 40MHz SM5006AKBS CF5006AKB Current consumption I DD INHN = open, V DD = 4.5 to 5.5V, f = 60MHz, Ta = 15 to 75 f = 60MHz, Ta = 0 to 70 Ta = 20 to 80 CF5006AKC CF5006DKC SM5006AKCS SM5006DKCS CF5006AKD CF5006BKC ma Ta = 15 to 75 CF5006CKD Ta = 0 to 70 SM5006AKDS SM5006BKCS SM5006CKDS INHN pull-up resistance R UP Measurement cct kω SM5006AKAS, CF5006AKA Feedback resistance R f Measurement cct 5 SM5006AKBS, CF5006AKB SM5006AKCS, CF5006AKC kω SM5006AKDS, CF5006AKD SM5006CKDS, CF5006CKD Built-in resistance Built-in capacitance R G Design value, determined by the R f value R D Design value, determined by the R f value C G Design value. A monitor pattern on a wafer is tested C D Design value. A monitor pattern on a wafer is tested Ω pf SEIKO NPC CORPORATION 9

10 5006AH series V DD = 4.5 to 5.5V, V SS = 0V, Ta = 40 to 85 unless otherwise noted. Parameter Symbol Condition HIGH-level output voltage V OH Q: Measurement cct 1, V DD = 4.5V, I OH = 4mA V LOW-level output voltage V OL Q: Measurement cct 2, V DD = 4.5V, I OL = 4mA V Output leakage current I Z Q: Measurement cct 2, INHN = LOW, V DD = 5.5V V OH = V DD 10 V OL = V SS 10 µa HIGH-level input voltage V IH INHN 2.0 V LOW-level input voltage V IL INHN 0.8 V f = 30MHz SM5006AHAS CF5006AHA f = 40MHz SM5006AHBS CF5006AHB Current consumption I DD INHN = open, V DD = 4.5 to 5.5V, f = 60MHz, Ta = 20 to 80 f = 60MHz, Ta = 15 to 75 CF5006AHC SM5006AHCS ma Ta = 20 to 80 CF5006AHD Ta = 15 to 75 SM5006AHDS INHN pull-up resistance R UP Measurement cct kω SM5006AHAS, CF5006AHA Feedback resistance R f Measurement cct 5 SM5006AHBS, CF5006AHB SM5006AHCS, CF5006AHC SM5006AHDS, CF5006AHD kω Built-in resistance Built-in capacitance R G Design value, determined by the R f value R D Design value, determined by the R f value C G Design value. A monitor pattern on a wafer is tested C D Design value. A monitor pattern on a wafer is tested Ω pf SEIKO NPC CORPORATION 10

11 Switching Characteristics 5006 N series 3V operation: V DD = 2.7 to 3.6V, V SS = 0V, Ta = 20 to 80 unless otherwise noted. Parameter Symbol Condition Output rise time Output fall time Output duty cycle *1 t r1 0.1V DD to 0.9V DD,, Ta = 10 to 70 t r2 0.1V DD to 0.9V DD, t f1 0.9V DD to 0.1V DD,, Ta = 10 to 70 t f2 0.9V DD to 0.1V DD, Duty Ta = 25, V DD = 3.3V,, f = 30MHz Ta = 25, V DD = 3.3V,, f = 40MHz Ta = 25, V DD = 3.3V,, f = 50MHz Ta = 25, V DD = 3.3V,, f = 70MHz *1. The duty cycle characteristic is checked the sample chips of each production lot. SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE Output disable delay time t PLZ 100 ns Ta = 25, V DD = 5V, C L 15pF Output enable delay time t PZL 100 ns ns ns % SEIKO NPC CORPORATION 11

12 5V operation: V DD = 4.5 to 5.5V, V SS = 0V, Ta = 40 to 85 unless otherwise noted. Parameter Symbol Condition Output rise time Output fall time t r1 0.1V DD to 0.9V DD, t r2 0.1V DD to 0.9V DD, C L = 30pF t r3 0.1V DD to 0.9V DD, C L = 50pF t f1 0.9V DD to 0.1V DD, t f2 0.9V DD to 0.1V DD, C L = 30pF t f3 0.9V DD to 0.1V DD, C L = 50pF SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE CF5006ANE CF5006ANF CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE CF5006ANE CF5006ANF CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE ns ns SEIKO NPC CORPORATION 12

13 Parameter Symbol Condition Output duty cycle *1 Duty Ta = 25, V DD = 5.0V f = 30MHz, C L = 50pF f = 40MHz, C L = 50pF f = 60MHz, C L = 50pF C L = 50pF f = 100MHz, C L = 30pF f = 100MHz, f = 107MHz, C L = 30pF f = 107MHz, f = 50MHz, C L = 50pF f = 100MHz, f = 60MHz, SM5006ANAS CF5006ANA SM5006ANBS CF5006ANB SM5006ANCS CF5006ANC SM5006ANDS CF5006AND SM5006BNCS CF5006BNC CF5006ANE SM5006ANES CF5006ANF CF5006BNE SM5006ANFS SM5006BNES SM5006CNCS CF5006CNC SM5006DNCS CF5006DNC SM5006CNES CF5006CNE SM5006DNES CF5006DNE SM5006CNCS CF5006CNC SM5006CNDS CF5006CND SM5006DNCS CF5006DNC Output disable delay time t PLZ 100 ns Ta = 25, V DD = 5V, C L 15pF Output enable delay time t PZL 100 ns *1. The duty cycle characteristic is checked the sample chips of each production lot. % SEIKO NPC CORPORATION 13

14 5006 K series V SS = 0V, Ta = 40 to 85 unless otherwise noted. Parameter Symbol Condition Output rise time t r 0.4V to 2.4V, V DD = 4.5 to 5.5V Output fall time t f 2.4V to 0.4V, V DD = 4.5 to 5.5V Output duty cycle *1 Duty Ta = 25, V DD = 5.0V, f = 30MHz f = 40MHz f = 60MHz f = 70MHz f = 50MHz *1. The duty cycle characteristic is checked the sample chips of each production lot. 2 4 C L = 50pF C L = 50pF 7 SM5006AKAS CF5006AKA SM5006AKBS CF5006AKB SM5006AKCS CF5006AKC SM5006AKDS CF5006AKD SM5006BKCS CF5006BKC SM5006DKCS CF5006DKC f = 70MHz SM5006CKDS CF5006CKD SM5006DKCS CF5006DKC Output disable delay time t PLZ 100 ns Ta = 25, V DD = 5V, C L 15pF Output enable delay time t PZL 100 ns ns ns % 5006AH series V DD = 4.5 to 5.5V, V SS = 0V, Ta = 40 to 85 unless otherwise noted. Parameter Symbol Condition Output rise time t r t r2 0.1V DD to 0.9V DD C L = 50pF Output fall time t f t f2 0.9V DD to 0.1V DD C L = 50pF f = 30MHz SM5006AHAS CF5006AHA Output duty cycle *1 Duty Ta = 25, V DD = 5.0V, f = 40MHz f = 50MHz f = 60MHz, Ta = 20 to 80 f = 60MHz, Ta = 15 to 75 Ta = 20 to 80 Ta = 15 to 75 *1. The duty cycle characteristic is checked the sample chips of each production lot. SM5006AHBS CF5006AHB SM5006AHCS CF5006AHC CF5006AHC SM5006AHCS CF5006AHD SM5006AHDS Output disable delay time t PLZ 100 ns Ta = 25, V DD = 5V, C L 15pF Output enable delay time t PZL 100 ns ns ns % SEIKO NPC CORPORATION 14

15 Current consumption and Output waveform with NPC s standard crystal Cb L Ca R f [MHz] R [Ω] L [mh] Ca [ff] Cb [pf] FUNCTIONAL DESCRIPTION Standby Function When INHN goes LOW, the oscillator output on Q goes high impedance. INHN Q Oscillator HIGH (or open) f O output frequency Normal operation LOW High impedance Normal operation SEIKO NPC CORPORATION 15

16 MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 Signal Generator R1 C1 Rfo XT XTN VSS Q R2 VSS 5.0V INHN RUP = IPR Q out monitor VOH 0V VIH A IPR 3.5V P P, 10MHz sine wave input signal (5V operation) 2.0V P P, 10MHz sine wave input signal (3V operation) C1 : 0.001µF R1 : 50Ω R2 : 250Ω (5006 N /5V operation) 275Ω (5006 N /3V operation) 245Ω (5006AKA, AKB, AKC, CKD, DKC) 250Ω (5006AKD, BKC) 975Ω (5006AH ) R fo : 2.7kΩ (5006B, D ) Measurement cct 2 Measurement cct 5 IOL, IZ XT INHN VSS Q V IZ VOL A A XT XTN VSS Rf = IRf IRf Measurement cct 3 A IDD IST Rfo XT X'tal XTN INHN VSS Q R fo : 2.7kΩ (5006B, D ) SEIKO NPC CORPORATION 16

17 Load cct 1 Load cct 2 Q output CL (Including probe capacitance) Q output CL (Including probe capacitance) 400Ω Switching Time Measurement Waveform Output duty level (CMOS) Q output DUTY measurement voltage (0.5V DD) tr TW tf Output duty level (TTL) Q output DUTY measurement voltage (1.4V DD) TW tr tf Output duty cycle (CMOS) Q output TW DUTY measurement voltage (0.5) T DUTY= TW/ T 100 (%) Output duty cycle (TTL) Q output TW DUTY measurement voltage (1.4) T DUTY= TW/ T 100 (%) SEIKO NPC CORPORATION 17

18 Output Enable/Disable Delay INHN VIL tplz VIH tpzl Q output INHN input waveform tr = tf 10ns SEIKO NPC CORPORATION 18

19 Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter Products ) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter NPC ). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SEIKO NPC CORPORATION 1-9-9, Hatchobori, Chuo-ku, Tokyo , Japan Telephone: Facsimile: sales@npc.co.jp NC9713FE SEIKO NPC CORPORATION 19