SM5160CM/DM OVERVIEW PINOUT FEATURES PACKAGE DIMENSIONS SERIES LINEUP. Programable PLL Frequency Synthesizer. (Top View)
|
|
|
- Felicia Rodgers
- 5 years ago
- Views:
Transcription
1 NIPPON PRECISION CIRCUITS INC. Programable PLL Frequency Synthesizer OVERVIEW PINOUT (Top View) The SM5160CM/DM is a PLL frequency synthesizer IC with programmable input and reference frequency dividers. The SM5160CM/DM features an unlock detector, outputs for use with active passive lowpass filters and direct frequency divider outputs. The SM5160CM/DM operates from 0.95 to 2.00 V and 2.0 to 3.3 V supplies and is available in 16-pin SSOPs. XIN XOUT VDD3 VSS TEST FEATURES Up to 95 MHz input frequency (, VDD= 0.98V) Up to 90 MHz input frequency (, VDD= 0.95V) Up to 13.0 MHz reference frequency (XIN) 1056 to programmable input frequency divider ratio 20 to programmable reference frequency divider ratio (SM5160CM) 20 to 8188 programmable reference frequency divider ratio (SM5160DM) Unlock detector Outputs for use with active and passive lowpass filters Direct outputs from frequency dividers 0.95 to 2.0 V and 2.0 to 3.3 V supplies Molybdenum- gate CMOS process 16-pin SSOP PACKAGE DIMENSIONS 0.6TYP (Unit: mm) SERIES LINEUP XIN SM5160CM Divider range 20 to (4 step) 1056 to Counter bits 14 bit 16 bit SM5160DM Divider range 20 to 8188 (4 step) 1056 to Counter bits 11 bit 16 bit NIPPON PRECISION CIRCUITS-1
2 BLOCK DIAGRAM XIN 1/4 PRESCAR XOUT 11 or 14 BIT R COUNTER VEL SHIFTER TEST 14 BIT LATCH LOCK DETECTOR 17 BIT SHIFT REGISTER PHASE DETECTOR VDD3 16 BIT LATCH CHARGE PUMP 16 BIT N COUNTER VEL SHIFTER PIN DESCRIPTION Number Name Description 1 XIN Reference oscillator or external clock input. Internal feedback resistor for AC coupling 2 XOUT Reference oscillator or external clock output. Oscillator is OFF when is LOW. 3 VDD3 Supply voltage for sections not supplied by and 4 Output to active lowpass filter. Single-ended, tristate output. Floating when is LOW 5 Output to passive lowpass filter. Single-ended, tristate output Floating when is LOW 6 VSS Ground 7 Comparison frequency input. Internal feedback resistor for AC coupling 8 Supply voltage for XIN and amplifiers 9 Supply voltage for N counter and R counter 10 Unlock detector output. LOW when PLL is unlocked. 11 Shift register clock input 12 Serial data input 13 Latch enable input 14 Input frequency divider buffered output. This is level-shifted and input to the phase detector. 15 Reference frequency divider buffered output. This is level-shifted and input to the phase detector. 16 TEST Test input. Internal pull-down resistor NIPPON PRECISION CIRCUITS-2
3 SPECIFICATIONS Absolute Maximum Ratings Parameter Symbol Condition Rating Unit Supply voltage range 1 VSS 0.3 to +7.0 V VSS Supply voltage range 2 VDD3-VSS 0.3 to +7.0 V Input voltage range VIN VSS 0.3 to VDD+0.3 V Operating temperature range TOPR 10 to +60 C Storage temperature range TSTG 40 to +125 C Soldering temperature range TS 250 C Soldering time range ts 10 sec Electrical Characteristics (= = 0.95 to 2.0V, VDD3= 2.0 to 3.3V, VSS= 0V, Ta= 10 to +60 C unless otherwise noted) Rating Parameter Symbol Condition min typ max Unit Supply voltage 1, and pins V Supply voltage 2 VDD3 VDD3 pin V = 90MHz, 0.5VP-P sine wave XIN= 12.8MHz, 0.5VP-P sine wave ma Current consumption IDD1 = = 0.95 to 1.05V (*1) = 95MHz, 0.5VP-P sine wave XIN= 12.8MHz, 0.5VP-P sine wave ma = = 0.98 to 1.08V Standby-mode current consumption IDD2 = = 0V 10 µa : 0.5VP-P sine wave 90 MHz maximum operating frequency fmax1 = = 0.95 to 2.0V : 0.5VP-P sine wave 95 MHz = = 0.98 to 2.0V XIN maximum operating frequency fmax2 XIN: 0.5VP-P sine wave 13 MHz minimum operating frequency fmin1 : 0.5VP-P sine wave 40 MHz XIN minimum operating frequency fmin2 XIN: 0.5VP-P sine wave 7 MHz and XIN input voltage VIN and XIN pins 0.5 VP-P, and VIH VDD3 0.3 V input voltage VIL 0.3 V XIN input current IIH1 VIH= 10 µa IIL1 VIL= 0V 10 µa input current IIH2 VIH= 60 µa IIL2 VIL= 0V 60 µa and IOH1 VDD3= 2.7 to 3.3V, VOH= VDD3 0.4V 1.0 ma output current IOL1 VDD3= 2.7 to 3.3V, VOL= 0.4V 1.0 ma, and IOH1 VOH= 0.4V 0.1 ma output current IOL1 VOH= 0.4V 0.1 ma to and to tsu1 2 µs setup time tsu2 2 µs hold time th 2 µs *1 Current consumption is the current consumed from and. NIPPON PRECISION CIRCUITS-3
4 Serial data input timing tsu1 th tsu2 Phase detector timing NIPPON PRECISION CIRCUITS-4
5 FUNCTIONAL DESCRIPTION SM5160CM/DM Lowpass Filter Connection An external lowpass filter connects to or. The output form the filter is fed to a voltage-controlled oscillator (VCO) which generates the PLL output. is intended for use with a passive filter as shown in figure 1. is intended for use with an active filter as shown in figure 2. R1 VCO R2 C Programmable Frequency Divider The input frequency divider and reference frequency divider ratios can be programmed using the serial data input. Input data consists of 16 data bits, in the order msb to lsb, followed by a control bit, as shown in figure 3 and 4. SM5160CM If the control bit is set to 0, the data is written to the 16-bit latch and then passed to the input frequency divider. If the control bit is set to 1, the 2 lsbs are ignored and the remaining data is written to the 14-bit latch and then passed to the reference frequency divider. 16BIT (N- COUNTER ) Figure 1. Passive lowpass filter circuit CONTROL LSB MSB VDD VDD ignored 14BIT (R- COUNTER ) 1: R-LATCH 0: N-LATCH R1 R2 C RL VCO Figure 3. Serial data format (SM5160CM) SM5160DM If the control bit is set to 0, the data is written to the 16-bit latch and then passed to the input frequency divider. 510kΩ If the control bit is set to 1, the 2 lsbs and 3msbs are ignored and the remaining data is written to the 11-bit latch and then passed to the reference frequency divider. Figure 2. Active lowpass filter circuit 16BIT (N- COUNTER ) CONTROL LSB MSB ignored 11BIT (R- COUNTER ) ignored 1: R-LATCH 0: N-LATCH Figure 4. Serial data format (SM5160DM) NIPPON PRECISION CIRCUITS-5
6 Serial data input timing Serial data input timing is shown in figure 5. Data is read on the rising edge of. The state on should be changed in sync with the falling edge of. should be LOW while data is being written to the shift register. When goes HIGH, data is transferred from the shift register to one of the frequency divider latches. Stand-by mode The stand-by mode is entered by setting, to 0V while the device is operation. In the stand-by mode, the amplifiers of XIN, and N/R counter are stopped. As long as voltage is provide to VDD3, data written in latch is kept. Exit from this mode to normal operation, therefore, is made by providing voltage to,. In this mode, input to must be done AC coupling, input to XIN must be done AC coupling or by crystal oscillator. In this mode,, should be in state of floating MSB LSB CONTROL Figure 5. Serial data input NIPPON PRECISION CIRCUITS-6
7 TYPICAL APPLICATION (For Ex. : in case of Pager) RF AMP 1'st MIX 1'st IF 2'nd MIX 2'nd IF B+ DISC WAVE SHAPER LPF Frequency Multiplier 3 1'st LO 2'nd LO SM5160 RAM ROM XIN XOUT VDD3 VSS TEST CPU LCD DRIVER DECODER DRIVER DC/ DC CONVERTER B++ Display B+ NIPPON PRECISION CIRCUITS INC. reserves the right to make changes to the products described in this data sheet in order to improve the design or performance and to supply the best possible products. Nippon Precision Circuits Inc. assumes no responsibility for the use of any circuits shown in this data sheet, conveys no license under any patent or other rights, and makes no claim that the circuits are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Nippon Precision Circuits Inc. makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification. The products described in this data sheet are not intended to use for the apparatus which influence human lives due to the failure or malfunction of the products. Customers are requested to comply with applicable laws and regulations in effect now and hereinafter, including compliance with export controls on the distribution or dissemination of the products. Customers shall not export, directly or indirectly, any products without first obtaining required licenses and approvals from appropriate government agencies. NIPPON PRECISION CIRCUITS INC. NIPPON PRECISION CIRCUITS INC. 4-3, 2-chome Fukuzumi, Koto-ku Tokyo, , JAPAN Telephon: Facsimile: NC9506AE NIPPON PRECISION CIRCUITS-7
CF5008A1 2. VCXO Module IC OVERVIEW FEATURES SERIES CONFIGURATION ORDERING INFORMATION
NIPPON PRECISION CIRCUITS INC. CF5008A1 VCXO Module IC OVERVIEW The CF5008A1 is a VCXO module IC that employs a circuit structure with low parasitic capacitance effects and a wide frequency range. Built-in
SM8141BV. EL Sheet Driver OVERVIEW PINOUT FEATURES PACKAGE DIMENSIONS ORDERING INFORMATION
NIPPON PRECISION CIRCUITS INC. SM141 EL Sheet Driver OVERVIEW The SM141 is a transformer-less electroluminescent (EL) sheet lamp driver, capable of driving sheets up to 50cm 2 in size. It employs built-in
ΣDECO SM5865BM D/A Converter for Digital Audio
NIPPON PRECISION CIRCUITS INC. ΣDECO SM5865BM D/A Converter for Digital Audio OVERVIEW PINOUT The SM5865BM is a 24-bit input D/A converter for digital audio equipment. It comprises newly developed DEM
LC7215, 7215F, 7215FM. MW/LW PLL Frequency Synthesizers. Package Dimensions. Overview. Features
Ordering number: EN 3584B Silicon-gate CMOS LSI LC7215, 7215F, 7215FM MW/LW PLL Frequency Synthesizers Overview The LC7215, LC7215F and LC7215FM are phase-locked-loop frequency synthesizer LSIs that provide
CF5073 series VCXO Module ICs with Built-in Varicap
XO Module ICs with Built-in Varicap OVERVIEW The CF5073 series are XO ICs with built-in varicap diode. They use a recently developed negative-resistance switching oscillation circuit, at oscillation startup
Low-Current Consumption, Real-Time Clock IC (General-Purpose IC)
S1T542XXD0A00 Low-Current Consumption, Real-Time Clock IC (General-Purpose IC) Operating power voltage 1.6 to 5.5V (-40 to +85 C) Output control 32.768kHz output function Clock power voltage 1.2 to 5.5V
TDA7326 AM-FM RADIO FREQUENCY SYNTHESIZER
AM-FM RADIO FREQUENCY SYNTHESIZER FM INPUT AND PRECOUNTER FOR UP TO 140MHz AM INPUT FOR UP TO 40MHz 6-BIT SWALLOW COUNTER, 8-BIT PRO- GRAMMABLE COUNTER FOR FM AND SW 14-BIT PROGRAMMABLE COUNTER FOR LW
CMOS MELODY IC. Enables to program up to 16 songs Provided with two built-in independent sound sources A 8-pin package OVERVIEW FEATURES
PF1095-01 SVM7561 SVM7561 Series CMOS MELODY IC Enables to program up to 16 songs Provided with two built-in independent sound sources A 8-pin package OVERVIEW SVM7561Series is the CMOS melody IC that
Low Power Consumption IPS009BL9_BL9A_BLAA AT Cut 32KHz SPXO
Description IPS009BL9, IPS009BL9A and is the specific SPXO IC for achieving 32KHz output by divide, corresponding to the fundamental crystal from 14MHZ to 27MHz and 33.554MHz corresponding to each IC.
Maintenance/ Discontinued
PLL LSI with Built-In Prescaler Overview The is a CMOS LSI for a phase-locked loop (PLL) frequency synthesizer with serial data parameter input. It consists of a two-coefficient prescaler, variable frequency
8-bit shift register and latch driver
8-bit shift register and latch driver The BU2114 and BU2114F are CMOS ICs with low power consumption, and are equipped with an 8-bit shift register latch. Data in the shift register can be latched asynchronously.
CF5074B VCXO Module IC with Built-in Varicap
XO Module IC with Built-in Varicap OVERVIEW The CF574B is XO module IC with built-in varicap diodes. The integrated varicap diode BiCMOS process allows the device to be fabricated on a single chip. newly
MC MOTOROLA CMOS SEMICONDUCTOR TECHNICAL DATA
SEMICONDUCTOR TECHNICAL DATA Order this document by MC456/D CMOS The MC456 is a phase locked loop (PLL) frequency synthesizer constructed in CMOS on a single monolithic structure. This synthesizer finds
PROGRAMMABLE FREQUENCY SYNTHESIZER (25MHz to 400MHz)
PROGRAMMABLE FREQUENCY SYNTHESIZER (25MHz to 400MHz) FEATURES Improved jitter performance over SY89429 25MHz to 400MHz differential PECL outputs ±25ps peak-to-peak output jitter Minimal frequency over-shoot
APPLICATIONS GENERAL DESCRIPTION FEATURES PIN CONFIGURATION PIN ASSIGNMENT /INH, Q0 PIN FUNCTION
CMOS Oscillation Frequency : 125MHz (MAX.) 3-State Output Built-in Oscillation Capacitor Built-in Oscillation Feedback Resistor Mini Mold SOT-26 Package APPLICATIONS Crystal Oscillation Modules Computer,
MB15E03SL ASSP. Single Serial Input PLL Frequency Synthesizer On-chip 1.2 GHz Prescaler DS E DESCRIPTION FEATURES PACKAGES
FUJITSU SEMICONDUCTOR DATA SHEET DS04-21359-4E ASSP Single Serial Input PLL Frequency Synthesizer On-chip 1.2 GHz Prescaler MB15E03SL DESCRIPTION The Fujitsu MB15E03SL is a serial input Phase Locked Loop
XC2300 Series GENERAL DESCRIPTION APPLICATIONS FEATURES PIN CONFIGURATION PIN ASSIGNMENT /INH, Q0 PIN FUNCTION. Tri-State Buffer ICs 1/7
ETR1406_001a Tri-State Buffer ICs GENERAL DESCRIPTION The 2300 Series are a group of high frequency, CMOS low power tri-state buffer ICs with input amplifier, divider and output tri-state buffer circuits
5076 series VCXO Module IC with Built-in Varicap
XO Module IC with Built-in Varicap OVERVIEW The 576 series are miniature XO ICs that provide a wide frequency pulling range, even when using miniature crystal units for which a wide pulling range is difficult
5075 series VCXO Module IC with Built-in Varicap
XO Module IC with Built-in Varicap OVERVIEW The 575 series are miniature XO ICs that provide a wide frequency pulling range, even when using miniature crystal units for which a wide pulling range is difficult
The SM8144 comprises an oscillator, booster, and high voltage switching circuit functional blocks. Boosting Block. Dividing Circuit 1/4
Application Note E Driver IC OVERVIEW The has an E ON/OFF control pin, (ON when HIGH, and OFF when OW). The inductor drive and E output frequencies are derived from a single built-in oscillator (), however,
VDD Series. AnaSem. Low voltage, Low power, ±1% High detect accuracy CMOS Voltage Detector with Delay circuit. Analog Semiconductor IC.
安纳森 Analog Semiconductor IC Low voltage, Low power, ±1% High detect accuracy CMOS Voltage Detector with Delay circuit (IMPORTANT: Please check the last page for Genuine Product Labeling) Rev. E13-1 Website:
FEATURES DESCRIPTION APPLICATIONS BLOCK DIAGRAM. PT2262 Remote Control Encoder
Remote Control Encoder DESCRIPTION PT2262 is a remote control encoder paired with PT2272 utilizing CMOS Technology. It encodes data and address pins into a serial coded waveform suitable for RF or IR modulation.
Single Serial Input PLL Frequency Synthesizer
FUJITSU SEMICODUCTO DATA SHEET DS04-21349-1E ASSP Single Serial Input PLL Frequency Synthesizer On-Chip prescaler MB15C03 DESCIPTIO The Fujitsu MB15C03 is a serial input Phase Locked Loop (PLL) frequency
PLL Frequency Synthesizer. Technical Data YYWW HPLL HPLL-8001
PLL Frequency Synthesizer Technical Data HPLL-8001 Features Low Operating Current Consumption (4 ma, typ.) High Input Sensitivity, High Input Frequencies (50 MHz) Synchronous Programming of the Counters
IPS009 series IC CMOS SPXO
IPS009 series IC Description IPS009 is the IC for SPXO corresponding to the fundamental crystal from 14MHZ to 100MHz, and operation voltage is 1.2V minimum, so it is the best for the application to the
SM1155 series Melody LSIs
Melody LSIs OVERVIEW The SM1155 series are CMOS melody LSIs that, together with a battery and piezoelectric buzzer. They also feature an oscillator stop function in non-play mode and a variable pull-down
DATASHEET CD4013BMS. Pinout. Features. Functional Diagram. Applications. Description. CMOS Dual D -Type Flip-Flop. FN3080 Rev 0.
DATASHEET CD013BMS CMOS Dual D -Type Flip-Flop FN300 Rev 0.00 Features High-Voltage Type (0V Rating) Set-Reset Capability Static Flip-Flop Operation - Retains State Indefinitely With Clock Level Either
ICS2694. Motherboard Clock Generator. Integrated Circuit Systems, Inc. Description. Features. Applications. Pin Configuration ICS2694
查询 ICS2694 供应商 Integrated Circuit Systems, Inc. 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 ICS2694 Motherboard Clock Generator Description The ICS2694 Motherboard Clock Generator is an integrated circuit using PLL and
CS SK DI DO NC TEST GND. Figure 1. Table 1
Rev.. CMOS SERIAL E 2 PROM The series are low power 4K/8K-bit E 2 PROM with a low operating voltage range. They are organized as 256-word 6-bit and 52-word 6bit, respectively. Each is capable of sequential
78A207 MFR1 Receiver DATA SHEET DESCRIPTION FEATURES OCTOBER 2005
DESCRIPTION The 78A207 is a single-chip, Multi-Frequency (MF) receiver that can detect all 15 tone-pairs, including ST and KP framing tones. This receiver is intended for use in equal access applications
XC2163 Series GENERAL DESCRIPTION APPLICATIONS FEATURES PIN ASSIGNMENT PIN CONFIGURATION /INH, Q0 PIN FUNCTION
ETR1403_001a ICs for use with 3rd Overtone Crystal Oscillators GENERAL DESCRIPTION The XC2163 series are high frequency, low current consumption CMOS ICs with built-in crystal oscillator and divider circuits.
Recommended crystal unit/ resonator. Fundamental, Fundamental, 3rd overtone, SAW. 80 to A1N No 2.5. SAW 110 to B1N
2.5V LVDS Output Oscillator ICs OVERVIEW The 5037 series are 2.5V operation, LVDS output oscillator ICs. They support 80MHz to 400MHz 3rd overtone oscillation and 80MHz to 600MHz fundamental oscillation.
NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.
PRESETTABLE BCD/DECADE UP/DOWN COUNTER PRESETTABLE 4-BIT BINARY UP/DOWN COUNTER The SN54/74LS192 is an UP/DOWN BCD Decade (8421) Counter and the SN54/74LS193 is an UP/DOWN MODULO- Binary Counter. Separate
16-bit stereo D / A converter for audio applications
6-bit stereo D / A converter for audio applications The is a 6-bit stereo D / A converter designed for audio applications, and has an internal 2 oversampling circuit. Applications 6-bit stereo D / A converter
IPS009 series IC CMOS SPXO
IPS009 series IC CMOS SPXO Description IPS009 is the IC for SPXO corresponding to the fundamental crystal from 14MHZ to 100MHz, and operation voltage is 1.2V minimum, so it is the best for the application
MB1503. LOW-POWER PLL FREQUENCY SYNTHESIZER WITH POWER SAVE FUNCTION (1.1GHz) Sept Edition 1.0a DATA SHEET. Features
Sept. 1995 Edition 1.0a MB1503 DATA SHEET LOW-POWER PLL FREQUENCY SYNTHESIZER WITH POWER SAVE FUNCTION (1.1GHz) The Fujitsu MB1503 is a serial input phase-locked loop (PLL) frequency synthesizer with a
Phase Detector. Selectable / 1,/ 2,/4,/8. Selectable / 1,/2
Programming Logic PL611-01 FEATURES Advanced programmable PLL design Very low Jitter and Phase Noise (30-70ps Pk-Pk typical) Up to 3 programmable outputs Output frequency up to 200MHz CMOS. Accepts Crystal
MOS INTEGRATED CIRCUIT
DATA SHEET MOS INTEGRATED CIRCUIT µpd6345 8 BIT SERIAL IN/PARALLEL OUT DRIVER The µpd6345 is a monolithic Bi-CMOS integrated Circuit designed to drive LED, Solenoid and Relay. This device consists of an
NT7603. Features. General Description
PRELIMINARY Single-Chip 16Cx2L Dot-Matrix LCD Controller / Driver Features Internal LCD drivers 16 common signal drivers 80 segment signal drivers Maximum display dimensions 16 characters * 2 lines or
Recommended crystal unit/ resonator. 5036G 80 to A1 5036A2 3rd overtone, 5036B 2. Fundamental,
2.5V LV-PECL Output Oscillator ICs OVERVIEW The 5036 series are 2.5V operation, differential LV-PECL output oscillator ICs. They support 50MHz to 400MHz 3rd overtone oscillation and 50MHz to 600MHz fundamental
ICS1561A. Differential Output PLL Clock Generator. Integrated Circuit Systems, Inc. Features. Description. Block Diagram
Integrated Circuit Systems, Inc. ICS1561A Differential Output PLL Clock Generator Description The ICS1561A is a very high performance monolithic PLL frequency synthesizer. Utilizing ICS s advanced CMOS
DATASHEET CD4027BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS Dual J-KMaster-Slave Flip-Flop. FN3302 Rev 0.
DATASHEET CD7BMS CMOS Dual J-KMaster-Slave Flip-Flop FN33 Rev. Features Pinout High Voltage Type (V Rating) Set - Reset Capability CD7BMS TOP VIEW Static Flip-Flop Operation - Retains State Indefinitely
Dual Tone Multiple Frequency Line Interface
SEMICONDUCTOR TECHNICAL DATA Order this document by /D Dual Tone Multiple Frequency Line Interface The is a silicon gate HCMOS LSI designed for general purpose Dual Tone Multiple Frequency (DTMF) communications,
NT7605. Features. General Description
PRELIMINARY Single-chip 20CX2L Dot-Matrix LCD Controller / Driver Features! Internal LCD drivers 6 common signal drivers 00 segment signal drivers! Maximum display dimensions 20 characters * 2 lines or
The following document contains information on Cypress products.
The following document contains information on Cypress products. FUJITSU MICROELECTRONICS DATA SHEET DS04-13501-3Ea Linear IC General purpose Converter CMOS D/A Converter for Digital Tuning (12 channels.
Preliminary. Charge-pump DC/DC Converter & Voltage Regulator S1F75510 DESCRIPTION FEATURES
PF1233-01 Preliminary S1F75510 Charge-pump DC/DC Converter & Voltage Regulator DESCRIPTION The S1F75510 is a power IC designed for use with medium or small capacity TFT LCD panel modules. A single chip
Description. Benefits CONTROL LOGIC. Rev 1.2, December 21, 2010 Page 1 of 12
3-Channel Clock Distribution Buffer Key Features Low current consumption: - 2.7mA-typ (VDD=1.8V, CL=0) 1.70V to 3.65V power supply operation MHz to 52MHz CLKIN range Supports LVCMOS or Sine Inputs Supports
unit: mm 3059-DIP22S unit: mm 3036B-MFP20
Ordering number : EN5743 CMOS IC LC72137, 72137M PLL Frequency Synthesizer for Electronic Tuning Overview The LC72137 and LC72137M are PLL frequency synthesizers for use in radio/cassette players. They
NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.
BCD DECADE/MODULO BINARY SYNCHRONOUS BI-DIRECTIONAL COUNTERS The SN54/ 74LS8 and SN54/ 74LS9 are fully synchronous 4-stage up/down counters featuring a preset capability for programmable operation, carry
SN54/74LS195A UNIVERSAL 4-BIT SHIFT REGISTER UNIVERSAL 4-BIT SHIFT REGISTER FAST AND LS TTL DATA 5-366
UNIVERSAL 4-BIT SHIFT REGISTER The SN54 / 74LS95A is a high speed 4-Bit Shift Register offering typical shift frequencies of 39 MHz. It is useful for a wide variety of register and counting applications.
Video switch for CANAL-Plus decoder
Video switch for CANAL-Plus decoder The BA7630S and BA7630F are decoder switching ICs for the scrambled broadcasts in France. The ICs include a 3- input multiplexer, -input multiplexers with amplifiers,
SN54/74LS196 SN54/74LS197 4-STAGE PRESETTABLE RIPPLE COUNTERS 4-STAGE PRESETTABLE RIPPLE COUNTERS FAST AND LS TTL DATA 5-372
4-STAGE PRESETTABLE RIPPLE COUNTERS The SN54/74LS196 decade counter is partitioned into divide-by-two and divide-by-five sectio which can be combined to count either in BCD (8, 4, 2, 1) sequence or in
SRM2B256SLMX55/70/10
256K-BIT STATIC RAM Wide Temperature Range Extremely Low Standby Current Access Time 100ns (2.7V) 55ns (4.5V) 32,768 Words 8-Bit Asynchronous DESCRIPTION The SRM2B256SLMX is a low voltage operating 32,768
SM8578BV Real-time Clock IC
Real-time Clock IC OVERVIEW The SM8578BV is a serial interface, real-time clock IC that uses a 32.768kHz crystal oscillator for its reference timing. It comprises second-counter to year-counter clock and
SG500. Low Jitter Spectrum Clock Generator for PowerPC Designs. Approved Product. FREQUENCY TABLE (MHz) PRODUCT FEATURES CONNECTION DIAGRAM
PRODUCT FEATURES Supports Power PC CPU s. Supports simultaneous PCI and Fast PCI Buses. Uses external buffer to reduce EMI and Jitter PCI synchronous clock. Fast PCI synchronous clock Separated 3.3 volt
A variety of pagers day of a week, hour, minute and second. TV set and VCR CPU interface via three wires
Rev.. REAL-TIME CLOCK is a CMOS real-time clock IC, which is designed to transfer or set each data of a clock and calender as requested by a CPU. This IC is connected to the CPU by three signal buses.
NJU6434C 1/4 DUTY LCD DRIVER PRELIMINARY ! GENERAL DESCRIPTION ! PACKAGE OUTLINE ! FEATURES ! BLOCK DIAGRAM
PRELIMINARY 1/4 DUTY LCD DRIVER! GENERAL DESCRIPTION The NJU6434 is a 1/4 duty LCD driver for segment type LCD panel. The LCD driver consists of 4-common and 50-segment drives up to 200 segments. The NJU6434
DESCRIPTION FEARURES. Applications
FEARURES Complete UHF transmitter 450MHz to 1000MHz Frequency Range Data Rates up to 10kbps ASK Output Power to 10dBm on 50ohm load Low external part count Operate with Crystals or Ceramic Resonators SOT23-6
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at ore.hu.
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu. CD49BMS December 199 Features High-Voltage Type (V Rating) Medium Speed
NT7605. Single-chip 20C X 2L Dot-Matrix LCD Controller / Driver. Features. General Description 1 V2.1
Single-chip 20C X 2L Dot-Matrix LCD Controller / Driver Features! Internal LCD drivers 6 common signal drivers 00 segment signal drivers! Maximum display dimensions 20 characters * 2 lines or 40 characters
S6A0093 Specification Revision History
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/wwwcrystalfontzcom/controlers/ S6A0093 80 SEG / 26 COM DRIVER & CONTROLLER FOR STN LCD March 2001 Ver 06 Contents in this document are subject
Low-Cost Notebook EMI Reduction IC. Applications. Modulation. Phase Detector
Low-Cost Notebook EMI Reduction IC Features Provides up to 15dB of EMI suppression FCC approved method of EMI attenuation Generates a 1X low EMI spread spectrum clock of the input frequency Operates between
Spread Spectrum Clock Generator AK8126
Spread Spectrum Clock Generator AK8126 Features Output Frequency Range: 16MHz 128MHz Configurable Spread Spectrum Modulation: - AKEMD s Original Spread Spectrum Profile - Modulation Ratio: Center Spread:
DATASHEET CD4060BMS. Pinout. Features. Functional Diagram. Oscillator Features. Applications. Description
DATASHEET CDBMS CMOS 1 Stage Ripple-Carry Binary Counter/Divider and Oscillator FN3317 Rev. Features Pinout High Voltage Type (V Rating) Common Reset 1MHz Clock Rate at 15V Fully Static Operation Q1 Q13
RF: RF Applicatant, normally omitted IR: IR Applicatant S: SOP-20 Package D: DIP-20 Package Omitted: DIP-18 Package SC Pin.
REMOTE CONTROL ENCODER DESCRIPTION The is a remote control encoder paired with SC5272 utilizing CMOS technology. It encodes data and address pins into a serial coded waveform suitable for RF or IR modulation.
LSI/CSI LS7560N LS7561N BRUSHLESS DC MOTOR CONTROLLER
LSI/CSI LS7560N LS7561N LSI Computer Systems, Inc. 15 Walt Whitman Road, Melville, NY 747 (631) 71-0400 FAX (631) 71-0405 UL A3800 BRUSHLESS DC MOTOR CONTROLLER April 01 FEATURES Open loop motor control
W588AXXX Data Sheet. 8-BIT MCU WITH VOICE SYNTHESIZER (PowerSpeech TM Series) Table of Contents-
Data Sheet 8-BIT MCU WITH VOICE SYNTHESIZER (PowerSpeech TM Series) Table of Contents- 1. GENERAL DESCRIPTION... 2 2. FEATURES... 2 3. PIN DESCRIPTION... 3 4. BLOCK DIAGRAM... 4 5. ELECTRICAL CHARACTERISTICS...
CARDINAL COMPONENTS. Operating Conditions: Description Min Max Unit
Standard Package Options Series CPP Part Numbering Example: CPP C 1 L Z - A5 B6 - XXXXXX TS CPP C 1 L Z A5 SERIES CPP OUTPUT C = CMOS T = TTL Specifications: PACKAGE STYLE 1 = Full Size 4 = Half Size 5
High Voltage CMOS Logic. <Logic Gate> General-purpose CMOS Logic IC Series (BU4S,BU4000B Series)
General-purpose CMOS Logic IC Series (BUS,BUB Series) High Voltage CMOS Logic ICs BUB/F,BUB/F/FV,BUB/F,BU7B/F, BUB/F/FV,BU9B/F/FV,BU9UB/F/FV,BUB/F/FV No.9EAT Description BUB series ICs are
PT2240B Encoder IC. has. High noise immunity. data codes into application. 4 Data pins. Car/Garage BLOCK
Encoder IC DESCRIPTION PT2240B is encoder utilizing CMOS Technology specially designed for remote control applications. It has 2 20 Address. It can support up to 4 Data Bits and is housed in 8 pin SOP
FEATURES DESCRIPTION APPLICATIONS BLOCK DIAGRAM. PT2272 Remote Control Decoder
Remote Control Decoder DESCRIPTION PT2272 is a remote control decoder paired with PT2262 utilizing CMOS Technology. It has 12-bit of tri-state address pins providing a maximum of 531,441 (or 312) address
5056 series Crystal Oscillator Module ICs
Crystal Oscillator Module ICs OVERVIEW The 556 series are 7 to 135MHz oscillation frequency, crystal oscillator module ICs optimized for 3rd overtone crystal elements with C 2 to 4pF. They have built-in
ST8016. Datasheet. 160 Output LCD Common/ Segment Driver IC. Version /05/25. Crystalfontz
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ 160 Output LCD Common/ Segment Driver IC Datasheet Version 1.9 2007/05/25 Note: Sitronix Technology Corp. reserves
CD4063BMS. CMOS 4-Bit Magnitude Comparator. Pinout. Features. Functional Diagram. Applications. Description. December 1992
CD3BMS December 99 Features CMOS -Bit Magnitude Comparator Pinout High Voltage Type (V Rating) Expansion to 8,,... N Bits by Cascading Units CD3BMS TOP VIEW Medium Speed Operation - Compares Two -Bit Words
Frequency Generator and Integrated Buffer for PENTIUM
Integrated Circuit Systems, Inc. ICS9159C-14 Frequency Generator and Integrated Buffer for PENTIUM General Description The ICS9159C-14 generates all clocks required for high speed RISC or CISC microprocessor
CD4094. CMOS 8-Stage Shift-and-Store Bus Register. Pinout. Features. Functional Diagram Applications. Description. December 1992
C494 ecember 1992 CMOS 8-Stage Shift-and-Store Bus Register Features Pinout High Voltage Type (2V Rating) 3-State Parallel Outputs for Connection to Common Bus C494BMS TOP VIEW Separate Serial Outputs
Remote Control Encoder IC
DESCRIPTION is a remote control encoder paired with PT2294 utilizing CMOS Technology. It encodes data and address pins into a serial coded waveform suitable for RF modulation. has a maximum of 12-bit of
ICS309 SERIAL PROGRAMMABLE TRIPLE PLL SS VERSACLOCK SYNTH. Description. Features. Block Diagram DATASHEET
DATASHEET ICS309 Description The ICS309 is a versatile serially-programmable, triple PLL with spread spectrum clock source. The ICS309 can generate any frequency from 250kHz to 200 MHz, and up to 6 different
Single Clock Generator
ASAHI KASEI EMD CORPORATION Single Clock Generator AK8113 Features Output Frequency Range: 74.17582MHz / 74.25MHz (Selectable) Input Frequency: 27MHz Low Jitter Performance: 15 ps (Typ.) Period, 1σ Low
HMC677G32 INTERFACE - SMT. 6-Bit SERIAL/PARALLEL SWITCH DRIVER/CONTROLLER. Typical Applications. Features. Functional Diagram. General Description
Typical Applications The is ideal for: Microwave and Millimeterwave Control Circuits Test and Measurement Equipment Complex Multi-Function Assemblies Military and Space Subsystems Transmit/Receive Module
DATASHEET CD4069UBMS. Features. Pinout. Applications. Functional Diagram. Description. Schematic Diagram. CMOS Hex Inverter
DATASHEET CD9UBMS CMOS Hex Inverter FN331 Rev. December 199 Features Pinout High Voltage Types (V Rating) Standardized Symmetrical Output Characteristics CD9UBMS TOP VIEW Medium Speed Operation: tphl,
Features. Support for external one-path, internal three-path D/A converter reference voltages
AK2330 DAC Type 8-bit 8-channel Electronic Volume Features 8-bit 8 channels of built-in multiplication D/A converters Support for external one-path, internal three-path D/A converter reference voltages
Remote Control Decoder IC
V1.2-1 - April, 2006 查询 供应商 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 DESCRIPTION is a remote control decoder paired with PT2264 utilizing CMOS Technology. It has 12 bits of tri-state address pins providing a maximum
5V/3.3V PROGRAMMABLE FREQUENCY SYNTHESIZER (25MHz to 400MHz)
5V/3.3V PROGRAMMABLE FREQUENCY SYNTHESIZER (25MHz to 400MHz) FEATURES 3.3V and 5V power supply options 25MHz to 400MHz differential PECL outputs 50ps peak-to-peak output jitter Minimal frequency over-shoot
Maintenance/ Discontinued
DATA SHEET Part No. AN26261A Package Code No. ULGA031-W-3525 includes following four Product lifecycle stage. Publication date: January 2006 1 Contents Overview. 3 Features.. 3 Applications 3 Package.
Low voltage 16-bit constant current LED sink driver with auto power-saving. Description
Low voltage 16-bit constant current LED sink driver with auto power-saving Datasheet - production data Features Low voltage power supply down to 3 V 16 constant current output channels Adjustable output
MOSA ELECTRONICS. Features. Description. MS8870 DTMF Receiver
Features Complete DTMF receiver Low power consumption Adjustable guard time Central Office Quality CMOS, Single 5V operation Description O rdering Information : 18 PIN DIP PACKAGE The is a complete DTMF
CDC MHz CLOCK SYNTHESIZER/DRIVER FOR PC MOTHERBOARDS WITH 3-STATE OUTPUTS
Supports Pentium III Class Motherboards Uses a 14.318-MHz Crystal Input to Generate Multiple Output Frequencies Includes Spread Spectrum Clocking (SSC), 0.5% Downspread for Reduced EMI Performance Power
LC75836WS-T/D. 1/4-Duty General-Purpose LCD Driver
1/4-Duty General-Purpose LCD Driver Overview The LC75836WS-T is 1/4-duty general-purpose microprocessor-controlled LCD driver that can be used in applications such as frequency display in products with
ITM-1601A LCM. User s Guide. (Liquid Crystal Display Module) 1998 Intech LCD Group Ltd. Document No. TE nd Edition Jan.
User s Guide Document No. TE-014-001 2 nd Edition Jan. 1999 ITM-1601A LCM 16 Characters X 1 lines with 5 X 8 dots format (Liquid Crystal Display Module) 1998 Intech LCD Group Ltd. ITM-1601A LCM Use s Guide
STP16CP05. Low voltage 16-bit constant current LED sink driver. Description. Features
Low voltage 16-bit constant current LED sink driver Datasheet - production data Features Low voltage power supply down to 3 V 16 constant current output channels Adjustable output current through external
NT Output LCD Segment/Common Driver NT7703. Features. General Description. Pin Configuration 1 V1.0
160 Output LCD Segment/Common Driver Features (Segment mode)! Shift Clock frequency: 14 MHz (Max.) (VDD = 5V ± 10%) 8 MHz (Max.) (VDD = 2.5V - 4.5V)! Adopts a data bus system! 4-bit / 8-bit parallel input
MARKING DIAGRAMS* ORDERING INFORMATION KPT23 ALYW SO 8 D SUFFIX CASE 751 TSSOP 8 DT SUFFIX CASE 948R KA23 ALYW
The MC00EPT23 is a dual differential LVPECL to LVTTL translator. Because LVPECL (Positive ECL) levels are used, only +3.3 V and ground are required. The small outline -lead package and the dual gate design
LC8904Q. Digital Audio Interface Receiver
Ordering number : EN*5014B CMOS LSI LC8904Q Digital Audio Interface Receiver Preliminary Overview The LC8904Q demodulates data transmitted between digital audio equipment in the EIAJ format (CP-1201) to
PIN CONNECTIONS ORDERING INFORMATION FUNCTIONAL TABLE
The MC12026 is a high frequency, low voltage dual modulus prescaler used in phase locked loop (PLL) applications. The MC12026A can be used with CMOS synthesizers requiring positive edges to trigger internal
LOW POWER SCHOTTKY. MARKING DIAGRAMS GUARANTEED OPERATING RANGES
The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops appear transparent to the data (data changes asynchronously) when Latch Enable (LE) is
ICS2494 ICS2494A. Dual Video/Memory Clock Generator. Integrated Circuit Systems, Inc. New Features. Features. Applications.
Integrated Circuit Systems, Inc. ICS2494 Dual Video/Memory Clock Generator Features World standard has been reconfigured to allow 8 memory frequencies. Maskprogrammable frequencies Preprogrammed versions
RS5C313 ULTRA-COMPACT REAL-TIME CLOCK IC OUTLINE FEATURES NO.EA
ULTRA-COMPACT REAL-TIME CLOCK IC RS5C313 NO.EA-034-0208 OUTLINE The RS5C313 is a CMOS type real-time clock which is connected to the CPU via three signal lines and capable of serial transmission of clock
SM5006 series Crystal Oscillator Module ICs
Crystal Oscillator Module ICs OVERVIEW The SM5006 series are crystal oscillator module ICs, that incorporate high-frequency, low current consumption oscillator and output buffer circuits. Highly accurate
CD40174BMS. CMOS Hex D -Type Flip-Flop. Features. Pinout. Applications. Functional Diagram. Description. December 1992
SEMICONDUCTOR CD17BMS December 199 CMOS Hex D -Type Flip-Flop Features Pinout High Voltage Type (V Rating) 5V, and 15V Parametric Ratings CD17BMS TOP VIEW Standardized, Symmetrical Output Characteristics