UNISONIC TECHNOLOGIES CO., LTD 4066 CMOS IC

Transcription

1 UNISONIC TECHNOLOGIES CO., LTD QUAD BILATERAL SWITCH DESCRIPTION The UTC 4066 is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals. FEATURES * Wide supply voltage range: 3V ~ 15V. * High noise immunity : 0.45 (typ.) * Wide range of digital and ± 7.5V PEAK analog switching * ON resistance for 15V operation : 80Ω * Matched ON resistance : R ON =5Ω (typ.) over 15V signal input * ON resistance flat over peak-to-peak signal range * High ON / OFF : 65 db (typ.) output voltage f IS =10kHz, =10kΩ * High degree linearity: 0.1% distortion f IS =1kHz, V IS =5Vp-p. * -V SS =1, =10kΩ * Extremely low OFF : 0.1nA (typ.) * switch -V SS =1, T A =25 C * Extremely high control input impedance : Ω (typ.) * Low crosstalk : -50dB (typ.) * between f IS =0.9MHz, =1kΩ * Frequency response, switch ON : 40MHz (typ.) ORDERING INFORMATION Ordering Number Lead Free Halogen Free Package Packing 4066L-D14-T 4066G-D14-T DIP-14 Tube 4066L-S14-R 4066G-S14-R SOP-14 Tape Reel 4066L-P14-R 4066G-P14-R TSSOP-14 Tape Reel MARKING DIP-14 SOP-14 / TSSOP UTC Date Code L: Lead Free G: Halogen Free Lot Code 1 of 7 Copyright 2017 Unisonic Technologies Co., Ltd

2 PIN CONFIGURATION SCHEMATIC DIAGRAM UNISONIC TECHNOLOGIES CO., LTD 2 of 7

3 ABSOLUTE MAXIMUM RATINGS (V SS =, unless otherwise specified)) PARAMETER SYMBOL RATINGS UNIT Supply Voltage -0.5 ~ +18 V Input Voltage V IN -0.5 ~ V CC +0.5 V Power Dissipation DIP P D SOP-14/TSSOP mw Junction Temperature T J +125 C Storage Temperature T STG -40 ~ +150 C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS (V SS =, unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Supply Voltage 3 ~ 15 V Input Voltage V IN 0 ~ V Operating Temperature Range T OPR -40 ~ +85 C DC ELECTRICAL CHARACTERISTICS (V SS =, unless otherwise specified) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT =5V Quiescent Device Current I DD = μa =15V SIGNAL INPUTS AND OUTPUTS Input or Output Leakage Switch OFF I IS V C =0 ±0.1 ±50 na ON Resistance ON Resistance Between Any 2 of 4 Switches CONTROL INPUTS Low Level Input Voltage HIGH Level Input Voltage Input Current R ON R ON V ILC V IHC I IN =10kΩ~ ( -V SS /2) V C =, V SS ~ =10kΩ~ ( -V SS /2) V C =, V IS =V SS ~ =5V = =15V =5V 20 =1 10 =15V 5 V IS =V SS and =5V = and V SS = V I IS =±10μA =15V =5V =1 (Note) V =15V V SS =15V, V IS V SS, V C V SS ±10-5 ±0.3 μa Note: Conditions for V IHC : (a) V IS =, I OS =standard B series I OH. (b) V IS =, I OL =standard B series I OL Ω Ω UNISONIC TECHNOLOGIES CO., LTD 3 of 7

4 AC ELECTRICAL CHARACTERISTICS (AC Parameters are guaranteed by DC correlated testing) (T A =25 C, t R =t F =20 ns and V SS = unless otherwise) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT Propagation Delay Time Signal Input to Signal Output Propagation Delay Time Control Input to Signal Output High Impedance to Logical Level Propagation Delay Time Control Input to Signal Output Logical Level to High Impedance Sine Wave Distortion Frequency Response -Switch ON (Frequency at-3db) Feedthrough - Switch OFF (Frequency at 50 db) Crosstalk Between Any Two Switches(Frequency at-50db) Crosstalk; Control Input to Signal Output Maximum Control Input T PHL, T PLH t PZH, t PLZ t PHZ, t PLZ V C =, C L =50Pf (Figure1) =200k =1.0kΩ, C L =50pF (Fig. 2, 3) =1.0kΩ, C L =50pF (Fig. 2, 3) V C = =5V, V SS = -5V =10kΩ, V IS =5V P-P, f=1khz, (Fig. 4) V C = =5V, V SS = -5V =1kΩ, V IS =5Vp-p 20 Log10 / (1kHz)-dB (Fig. 4) =5., V CC =V SS = -5., =1kΩ, V IS =5. P-P, 20Log 10, /V IS = -50dB, (Fig. 4) =V C (A)=5.; V SS =V C (B)=5., =1kΩ, V IS (A)=5. P-P, 20Log 10, (B)/V IS (A)= -50dB (Fig. 5) =1, =10kΩ, R IN =1.0kΩ, V CC =1 Square Wave, C L =50pF (Fig. 6) =1.0kΩ, C L =50pF (Fig. 7) (f) =1/2Vos (1.0kHz) =5V = =15V =5V 125 =1 60 =15V 50 =5V 125 =1 60 =15V 50 = =1 8.0 =15V 8.5 ns ns ns 0.1 % 40 MHz 1.25 MHz 0.9 MHz 150 mv p-p Signal Input Capacitance C IS 8.0 pf Signal Output Capacitance C OS =1 8.0 pf Feedthrough Capacitance C IOS V C = 0.5 pf Control lnput Capacitance C IN pf MHz UNISONIC TECHNOLOGIES CO., LTD 4 of 7

5 SPECIAL CONSIDERATIONS In applications where separate power sources are used to drive and the signal input, the current capability should exceed / ( =effective external load of the UTC 4066 bilateral switches).this provision avoids any permanent current flow or clamp action of the supply when power is applied or removed from UTC In certain applications, the external load-resistor current may include both and Signal-line components. To avoid drawing current when switch current flows into terminals 1,4,8 or 11,the voltage drop across the bidirectional swith must not exceed 0.6V at T A 25 C, or 0.4V at T A >25 C (calculated from R ON values shown). NO current will flow through if the switch current flows into terminals2, 3, 9 or 10. AC TEST CIRCUITS AND SWITCHING TIME WAVEFORMS V C V IS = CONTROL V SS VDD 1KΩ C L 50pF V OL t PZL t PZL 50% 90% V OL t PLZ 10% t PLZ 50% Fig. 3 t PZL,t PLZ Propagation Delay Time Control to Signal Output UNISONIC TECHNOLOGIES CO., LTD 5 of 7

6 AC TEST CIRCUITS AND SWITCHING TIME WAVEFORMS(Cont.) V C (1)= 5V V IS (1) V C (2)=Vss CONTROL Vss -5V 5V 1kΩ (1) V IS 2.5V -2.5V 1/f V IS (2)= CONTROL Vss -5V 1kΩ (2) Fig. 5 Crosstalk Between Any Two Switches V C V IS = CONTROL V SS t F t F C L 50pF 1kΩ VC 50%90% 50% 10% 10% 1/f 1kHz Fig. 7 Maximum Control Input Frequency UNISONIC TECHNOLOGIES CO., LTD 6 of 7

7 TYPICAL PERFORMANCE CHARACTERISTICS UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD 7 of 7