(250 Volts Peak) COUPLER SCHEMATIC. MAXIMUM RATINGS (TA = 25 C unless otherwise noted) Rating Symbol Value Unit STYLE 6 PLASTIC

Transcription

1 (0 Volts Peak) The Series consists of gallium arsenide infrared emitting diodes, optically coupled to silicon bilateral switch and are designed for applications requiring isolated triac triggering, low current isolated ac switching, high electrical isolation (to 700 Vac peak), high detector standoff voltage, small size, and low cost. To order devices that are tested and marked per VDE 088 requirements, the suffix V must be included at end of part number. VDE 088 is a test option. Recommended for Vac(rms) Applications: Solenoid/Valve Controls Lamp Ballasts Interfacing Microprocessors to Vac Peripherals Motor Controls Static ac Power Switch Solid State Relays Incandescent Lamp Dimmers MAXIMUM RATINGS (TA = C unless otherwise noted) INFRARED EMITTING DIODE Rating Symbol Value Unit Reverse Voltage VR 3 Volts Forward Current Continuous IF 0 ma Total Power TA = C Negligible Power in Transistor Derate above C OUTPUT DRIVER PD mw mw/ C Off State Output Terminal Voltage VDRM 0 Volts Peak Repetitive Surge Current (PW = ms, 0 pps) Total Power TA = C Derate above C TOTAL DEVICE Isolation Surge Voltage() (Peak ac Voltage, 0 Hz, Second Duration) Total Power TA = C Derate above C ITSM A PD 300 mw mw/ C VISO 700 Vac(pk) PD 330. mw mw/ C Junction Temperature Range TJ 0 to +00 C Ambient Operating Temperature Range() TA 0 to +8 C Storage Temperature Range() Tstg 0 to +0 C Soldering Temperature (0 s) TL 0 C. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating.. For this test, Pins and are common, and Pins, and are common.. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc. [IFT = ma Max] [IFT = 0 ma Max] [IFT = ma Max] *Motorola Preferred Device STYLE PLASTIC STANDARD THRU HOLE CASE 730A 0 COUPLER SCHEMATIC 3. ANODE. CATHODE 3. NC. MAIN TERMINAL. SUBSTRATE DO NOT CONNECT. MAIN TERMINAL

2 ELECTRICAL CHARACTERISTICS (TA = C unless otherwise noted) I INPUT LED Reverse Leakage Current (VR = 3 V) Characteristic Symbol Min Typ Max Unit IR µa Forward Voltage (IF = 0 ma) OUTPUT DETECTOR (IF = 0 unless otherwise noted) Peak Blocking Current, Either Direction (Rated VDRM () ) Peak On State Voltage, Either Direction (ITM = 00 ma Peak) VF.. Volts IDRM 0 00 na VTM.8 3 Volts Critical Rate of Rise of Off State Voltage (Figure 7, Note ) dv/dt 0 V/µs COUPLED LED Trigger Current, Current Required to Latch Output (Main Terminal Voltage = 3 V(3)) MOC30 MOC30 Holding Current, Either Direction IH 00 µa. Test voltage must be applied within dv/dt rating.. This is static dv/dt. See Figure 7 for test circuit. Commutating dv/dt is a function of the load driving thyristor(s) only. 3. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended operating IF lies between max 3. IFT ( ma for, 0 ma for MOC30, ma for MOC30) and absolute max IF (0 ma). IFT ma TYPICAL ELECTRICAL CHARACTERISTICS TA = C +800 VF, FORWARD VOLTAGE (VOLTS).8... TA = 0 C C PULSE ONLY PULSE OR DC TM, ON-STATE CURRENT (ma) C IF, LED FORWARD CURRENT (ma) VTM, ON STATE VOLTAGE (VOLTS) Figure. LED Forward Voltage versus Forward Current Figure. On State Characteristics

3 NORMALIZED IFT TA, AMBIENT TEMPERATURE ( C) 00 I FT, NORMALIZED LED TRIGGER CURRENT NORMALIZED TO: PWin 00 µs PWin, LED TRIGGER WIDTH (µs) 00 Figure 3. Trigger Current versus Temperature Figure. LED Current Required to Trigger versus LED Pulse Width dv/dt, STATIC (V/µ s) 0 8 STATIC dv/dt CIRCUIT IN FIGURE TA, AMBIENT TEMPERATURE ( C) Figure. dv/dt versus Temperature Vdc PULSE INPUT MERCURY WETTED RELAY RTEST CTEST D.U.T. R = 0 kω X00 SCOPE PROBE. The mercury wetted relay provides a high speed repeated pulse to the D.U.T.. 00x scope probes are used, to allow high speeds and voltages. 3. The worst case condition for static dv/dt is established by triggering the D.U.T. with a normal LED input current, then removing the current. The variable RTEST allows the dv/dt to be gradually increased until the D.U.T. continues to trigger in response to the applied voltage pulse, even after the LED current has been removed. The dv/dt is then decreased until the D.U.T. stops triggering. RC is measured at this point and recorded. APPLIED VOLTAGE WAVEFORM 8 V Vmax = 0 V 0 VOLTS RC dv dt 0.3 V max RC 8 RC Figure. Static dv/dt Test Circuit

4 NOTE: This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only. Additional information on the use of the /30/30 is available in Application Note AN 780A. TYPICAL APPLICATION CIRCUITS VCC Rin MOC30 MOC30 80 RL 0 V 0 Hz VCC Rin MOC30 MOC µf C. k ZL 0 V 0 Hz Figure 7. Resistive Load Figure 8. Inductive Load with Sensitive Gate Triac (IGT ma) ZL VCC Rin MOC30 MOC µf C. k 0 V 0 Hz Figure 9. Inductive Load with Non Sensitive Gate Triac ( ma IGT 0 ma)

5 PACKAGE DIMENSIONS A 3 B NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 98.. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. T SEATING PLANE F PL E PL N C L K G M D PL 0.3 (0.00) M T A M B M J PL 0.3 (0.00) M T B M A M INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G 0.00 BSC. BSC J K L BSC 7. BSC M 0 0 N STYLE : PIN. ANODE. CATHODE 3. NC. MAIN TERMINAL. SUBSTRATE. MAIN TERMINAL CASE 730A 0 ISSUE G A 3 B NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 98.. CONTROLLING DIMENSION: INCH. F PL E PL G H D PL C L K PL 0.3 (0.00) M T A M B M J T SEATING PLANE 0.3 (0.00) M T B M A M CASE 730C 0 ISSUE D INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G 0.00 BSC. BSC H J K L 0.30 BSC 8.3 BSC S *Consult factory for leadform option availability

6 F PL T SEATING PLANE A B 3 N C G K L J NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 98.. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G 0.00 BSC. BSC J K L N D PL E PL 0.3 (0.00) M T A M B M *Consult factory for leadform option availability CASE 730D 0 ISSUE D