SEMICONDUCTOR TECHNICAL DATA

Size: px

Start display at page:

Download "SEMICONDUCTOR TECHNICAL DATA"

Giles Carroll
6 years ago
Views:

1 SEMICONDUCTOR TECHNICAL DATA Order this document by N/D The N, N and N7 devices consist of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon phototransistor detector. Current Transfer Ratio 00% Specified Conditions Guaranteed Switching Speeds Meets or Exceeds all JEDEC Registered Specifications To order devices that are tested and marked per VDE 088 requirements, the suffix V must be included at end of part number. VDE 088 is a test option. Applications General Purpose Switching Circuits Interfacing and coupling systems of different potentials and impedances Regulation Feedback Circuits Monitor & Detection Circuits Solid State Relays MAXIMUM RATINGS (TA = C unless otherwise noted) INPUT LED GlobalOptoisolator Rating Symbol Value Unit Reverse Voltage VR Volts Forward Current Continuous IF 0 ma LED Power TA = C with Negligible Power in Output Detector Derate above C OUTPUT TRANSISTOR PD 0. mw mw/ C Collector Emitter Voltage VCEO 0 Volts Emitter Base Voltage VEBO 7 Volts Collector Base Voltage VCBO 70 Volts Collector Current Continuous IC 0 ma Detector Power TA = C with Negligible Power in Input LED Derate above C PD 0.7 mw mw/ C [CTR = 00% Min] *Motorola Preferred Device STANDARD THRU HOLE CASE 70A 0 STYLE PLASTIC SCHEMATIC PIN. LED ANODE. LED CATHODE. N.C.. EMITTER. COLLECTOR. BASE TOTAL DEVICE Isolation Source Voltage() (Peak ac Voltage, 0 Hz, sec Duration) VISO 700 Vac(pk) Total Device Power TA = C Derate above C PD 0.9 mw mw/ C Ambient Operating Temperature Range() TA to +00 C Storage Temperature Range() Tstg to +0 C Soldering Temperature (0 sec, / from case) TL 0 C. Isolation surge voltage is an internal device dielectric breakdown rating.. For this test, Pins and are common, and Pins, and are common.. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc. REV Motorola, Inc. Optoelectronics 99 Device Data

2 ELECTRICAL CHARACTERISTICS (TA = C unless otherwise noted)() INPUT LED Characteristic Symbol Min Typ() Max Unit Forward Voltage (IF = 0 ma) TA = C TA = C TA = 00 C VF Reverse Leakage Current (VR = V) IR 0 µa Capacitance (V = 0 V, f = MHz) CJ 8 pf OUTPUT TRANSISTOR Collector Emitter Dark Current (VCE = 0 V, TA = C) Collector Emitter Dark Current (VCE = 0 V, TA = 00 C) Collector Base Dark Current (VCB = 0 V) TA = C TA = 00 C ICEO...0 ICBO Collector Emitter Breakdown Voltage (IC = ma) V(BR)CEO 0 V Collector Base Breakdown Voltage (IC = 00 µa) V(BR)CBO V Emitter Base Breakdown Voltage (IE = 00 µa) V(BR)EBO V DC Current Gain (IC = ma, VCE = V) hfe 00 Collector Emitter Capacitance (f = MHz, VCE = 0) CCE 7 pf Collector Base Capacitance (f = MHz, VCB = 0) CCB 9 pf Emitter Base Capacitance (f = MHz, VEB = 0) CEB 9 pf COUPLED Output Collector Current TA = C (IF = 0 ma, VCE = 0 V) TA = C TA = 00 C IC (CTR)() 0 (00) (0) (0) 0 (00) Collector Emitter Saturation Voltage (IC = 0. ma, IF = 0 ma) VCE(sat) V Turn On Time ton 7. 0 µs Turn Off Time (IC = ma, VCC = 0 V, Rise Time RL = 00 Ω)() toff.7 0 tr. Fall Time tf.7 V na µa na ma (%) Isolation Voltage (f = 0 Hz, t = sec) VISO 700 Vac(pk) Isolation Current() (VI O = 0 Vpk) Isolation Current (VI O = 00 Vpk) Isolation Current (VI O = 00 Vpk) N N N7 IISO Isolation Resistance (V = 00 V)() RISO 0 Ω Isolation Capacitance (V = 0 V, f = MHz)() CISO 0. pf. Always design to the specified minimum/maximum electrical limits (where applicable).. Current Transfer Ratio (CTR) = IC/IF x 00%.. For test circuit setup and waveforms, refer to Figure.. For this test, Pins and are common, and Pins, and are common µa Motorola Optoelectronics Device Data

3 I TYPICAL CHARACTERISTICS VF, FORWARD VOLTAGE (VOLTS).8... TA = C PULSE ONLY PULSE OR DC C 00 C IF, LED FORWARD CURRENT (ma) IC, OUTPUT COLLECTOR CURRENT (NORMALIZED) 0 0. NORMALIZED TO: IF = 0 ma Figure. LED Forward Voltage versus Forward Current Figure. Output Current versus Input Current IC, COLLECTOR CURRENT (ma) 8 IF = 0 ma 0 ma 8 ma ma VCE, COLLECTOR EMITTER VOLTAGE (VOLTS), OUTPUT COLLECTOR CURRENT (NORMALIZED) IC NORMALIZED TO TA = C TA, AMBIENT TEMPERATURE ( C) Figure. Collector Current versus Collector Emitter Voltage Figure. Output Current versus Ambient Temperature, COLLECTOR EMITTER DARK CURRENT (NORMALIZED) CEO 00 0 NORMALIZED TO: VCE = 0 V TA = C VCE = 0 V 0 V TA, AMBIENT TEMPERATURE ( C) Figure. Dark Current versus Ambient Temperature t, TIME ( µ s) RL = 000{ RL = 00{ Figure. Rise and Fall Times (Typical Values) tr tf tf tr VCC = 0 V Motorola Optoelectronics Device Data

4 VCC = 0 V VCC = 0 V, TURN ON TIME ( s) t on µ RL = , TURN OFF TIME ( s) t off µ RL = Figure 7. Turn On Switching Times Figure 8. Turn Off Switching Times I C, TYPICAL COLLECTOR CURRENT (ma) IF = 0 IB = 7 µa Figure 9. DC Current Gain (Detector Only) µa µa µa µa µa µa VCE, COLLECTOR EMITTER VOLTAGE (VOLTS) C, CAPACITANCE (pf) CLED CCB CEB CCE f = MHz V, VOLTAGE (VOLTS) Figure 0. Capacitances versus Voltage TEST CIRCUIT VCC = 0 V WAVEFORMS INPUT PULSE IC RL = 00 Ω INPUT OUTPUT 0% 90% OUTPUT PULSE INPUT CURRENT ADJUSTED TO ACHIEVE IC = ma. ton tr tf toff Figure. Switching Time Test Circuit and Waveforms Motorola Optoelectronics Device Data

5 PACKAGE DIMENSIONS A B NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 98.. CONTROLLING DIMENSION: INCH.. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. T SEATING PLANE F PL E PL N C L K G M D PL 0. (0.00) M T A M B M J PL 0. (0.00) M T B M A M INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G 0.00 BSC. BSC J K L 0.00 BSC 7. BSC M 0 0 N STYLE : PIN. ANODE. CATHODE. NC. EMITTER. COLLECTOR. BASE CASE 70A 0 ISSUE G A B NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 98.. CONTROLLING DIMENSION: INCH. F PL E PL G H D PL C L K PL 0. (0.00) M T A M B M J T SEATING PLANE 0. (0.00) M T B M A M CASE 70C 0 ISSUE D INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G 0.00 BSC. BSC H J K L 0.0 BSC 8. BSC S *Consult factory for leadform option availability Motorola Optoelectronics Device Data

6 F PL T SEATING PLANE A B N L C G K D PL J NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 98.. CONTROLLING DIMENSION: INCH.. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G 0.00 BSC. BSC J K L N E PL 0. (0.00) M T A M B M *Consult factory for leadform option availability CASE 70D 0 ISSUE D Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi SPD JLDC, Toshikatsu Otsuki, P.O. Box 09; Phoenix, Arizona F Seibu Butsuryu Center, Tatsumi Koto Ku, Tokyo, Japan. 0 8 MFAX: RMFAX0@ .sps.mot.com TOUCHTONE (0) 09 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, INTERNET: NET.com Ting Kok Road, Tai Po, N.T., Hong Kong Motorola Optoelectronics Device N/D Data

7 This datasheet has been download from: Datasheets for electronics components.

SEMICONDUCTOR TECHNICAL DATA

SEMICONDUCTOR TECHNICAL DATA Order this document by MOC8020/D The MOC8020 and MOC802 devices consist of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon photodarlington