Thyristors 8 Amp Sensitive & Standard SCRs. Sxx08xSx & Sxx08x Series. Description

Transcription

1 Sxx08xSx & Sxx08x Series RoHS Description This Sxx08x SCR series is ideal for uni-directional switch applications such as phase control, heating, motor speed controls, converters/rectifiers and capacitive discharge ignitions. These SCRs have a low gate current trigger level of 0.2 to 15 m at approximately 1.5V, with a sensitive version of this series having a gate trigger current less than 500µ. The sensitive gate SCR version is easily triggered by sense coils, proximity switches, and microprocessors. Features & Benefits gency pproval gency gency File Number L Package: E71639 Halogen Free and RoHS compliant Glass passivated junctions Voltage capability up to 0 V Surge capability up to at 60 Hz half cycle L - Package is UL recognized for 2500Vrms Main Features Symbol Value Unit I T(RMS) 8 RM /V RRM 400 to 0 V I GT 0.2 to 15 m pplications Typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. lso C control & rectification for power tools, home/brown goods, white goods appliances and 2-wheeler rectifier/ battery regulators. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. dditional Information Schematic Symbol K Datasheet Resources Samples G

2 bsolute Maximum Ratings Sensitive SCRs Symbol Parameter Test Conditions Value Unit I T(RMS) I T(V) I TSM RMS on-state current verage on-state current Peak non-repetitive surge current Sxx08LSy = 80 C Sxx08RSy/Sxx08NSy Sxx08DSy Sxx08VSy = 95 C Sxx08LSy = 80 C Sxx08RSy/Sxx08NSy Sxx08DSy Sxx08VSy = 95 C single half cycle; f = 50Hz; (initial) = 25 C single half cycle; f = 60Hz; (initial) = 25 C I 2 t I 2 t Value for fusing t p = 8.3 ms 41 2 s di/dt Critical rate of rise of on-state current f = 60 Hz ; = 110 C 70 /μs I GTM Peak gate current = 110 C 1.6 P G(V) verage gate power dissipation = 110 C 0.4 W T stg Storage temperature range -40 to 150 C Operating junction temperature range -40 to 110 C Note: xx = voltage, y = sensitivity 83 bsolute Maximum Ratings Standard SCRs Symbol Parameter Test Conditions Value Unit I T(RMS) I T(V) I TSM RMS on-state current verage on-state current Peak non-repetitive surge current Sxx08L = C Sxx08R/Sxx08N Sxx08D Sxx08V = 110 C Sxx08L = C Sxx08R/Sxx08N Sxx08D Sxx08V = 110 C single half cycle; f = 50Hz; (initial) = 25 C single half cycle; f = 60Hz; (initial) = 25 C I 2 t I 2 t Value for fusing t p = 8.3 ms 41 2 s di/dt Critical rate-of-rise of on-state current f = 60 Hz = 125 C /μs I GM Peak gate current = 125 C 2 P G(V) verage gate power dissipation = 125 C 0.5 W T stg Storage temperature range -40 to 150 C Note: xx = voltage Operating junction temperature range -40 to 125 C 83

3 Electrical Characteristics ( = 25 C, unless otherwise specified) Sensitive SCRs Value Symbol Test Conditions Sxx08xS1 Sxx08xS2 Sxx08xS3 Sxx08x4 Unit I GT = 6V R L = Ω MX μ V GT = 6V R L = Ω MX. 0.8 V dv/dt = RM ; R GK = 1kΩ; = 110 C TYP. 8 V/μs V GD = RM R L = 3.3 kω = 110 C MIN. 0.2 V V GRM I GR = 10μ MIN. 6 V I H I T = 20m (initial) MX m t q I T =2; t p =50µs; dv/dt=5v/µs; di/dt=-30/µs MX μs t gt I G = 2 x I GT PW = 15µs I T = 12 TYP μs Note: xx = voltage x = package Electrical Characteristics ( = 25 C, unless otherwise specified) Standard SCRs Symbol Test Conditions Value Sxx08x Unit I GT = 12V R L = 60 Ω MX. 15 m V GT = 12V R L = 60 Ω MX. 1.5 V 400V 350 = RM ; gate open; = C 600V V 250 dv/dt 0V MIN. V/μs 400V 250 = RM ; gate open; = 125 C 600V V 200 V GD = RM R L = 3.3 kω = 125 C MIN. 0.2 V I H I T = 200m (initial) MX. 30 m t q I T =2; t p =50µs; dv/dt=5v/µs; di/dt=-30/µs MX. 35 μs t gt I G = 2 x I GT PW = 15µs I T = 16 TYP. 2 μs Note: xx = voltage x = package Static Characteristics Symbol Test Conditions Value Unit V TM I T = 16; t p = 380 µs MX. 1.6 V Sxx08xyy = 25 C V 5 = 110 C V 250 I DRM / I RRM RM = V RRM = 25 C V 10 0V MX. 20 μ Sxx08x = C V 200 0V 3000 = 125 C V 500 Note: xx = voltage, x = package, yy = sensitivity

4 Thermal Resistances Symbol Parameter Value Unit Sxx08RSy / Sxx08NSy 1.8 Sxx08LSy 3.4 Sxx08VSy 2.1 R θ(j-c) Junction to case (C) Sxx08DSy 1.5 Sxx08R / S xx08n 1.8 C/W Sxx08L 3.4 Sxx08V 2.0 Sxx08D 1.5 Sxx08RSy 40 Sxx08LSy 65 R θ(j-) Junction to ambient Sxx08VSy 85 Sxx08R 40 C/W Sxx08L 50 Sxx08V 70 Note: xx = voltage, y = sensitivity Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature (Sensitive SCR) Figure 2: Normalized DC Gate Trigger Current vs. Junction Temperature (Standard SCR) Ratio of I GT / I GT ( = 25 C) Ratio of I GT / I GT ( = 25 C) Junction Temperature ( ) - ( C) Junction Temperature ( ) - ( C) 125

5 Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature Figure 4: Normalized DC Holding Current vs. Junction Temperature Ratio of V GT / V GT ( = 25 C) Ratio of I H / I H ( = 25 C) Junction Temperature ( ) - ( C) Junction Temperature ( ) - ( C) 125 Figure 5: On-State Current vs. On-State Voltage (Typical) Figure 6: Power Dissipation (Typical) vs. RMS On-State Current 32 8 Instantaneous On-state Current (i T ) mps = 25 C Instantaneous On-state Voltage (v T ) Volts verage On-State Power Dissipation [P D(V) ] -- (Watts) RMS On-State Current [I T(RMS) ] - (mps) Figure 7: Maximum llowable Case Temperature vs. RMS On-State Current Figure 8: Maximum llowable Case Temperature vs. verage On-State Current Maximum llowable Case Temperature ( ) - C Sxx08RSy/ Sxx08NSy Sxx08RSy Sxx08DSy Sxx08VSy Sxx08R/Sxx08N Sxx08D Sxx08V CURRENT WVEFORM: Sinusoidal LOD: Resistive or Inductive Conduction ngle: 180 FREE IR RTING Sxx08LSy Sxx08L RMS On-State Current [I T(RMS) ] - mps Maximum llowable Case Temperature ( ) - C Sxx08RSy/ Sxx08RSy Sxx08NSy Sxx08DSy Sxx08VSy Sxx08R/Sxx08N Sxx08D Sxx08V Sxx08L 95 Sx08LSy 90 CURRENT WVEFORM: Sinusoidal LOD: Resistive or Inductive 85 Conduction ngle: 180 FREE IR RTING verage On-State Current [I T(VE) ] - mps

6 Figure 9: Maximum llowable mbient Temperature vs. RMS On-State Current Figure 10: Maximum llowable mbient Temperature vs. verage On-State Current Maximum llowable mbient Temperature (T ) - C Sxx08RSy Sxx08LSy Sxx08R Sxx08VSy Sxx08L CURRENT WVEFORM: Sinusoidal LOD: Resistive or Inductive CONDUCTION NGLE: 180 FREE IR RTING Sxx08V RMS On-State Current [I T(RMS) ] - mps Maximum llowable mbient Temperature (T ) - C Sxx08RSy Sxx08LSy Sxx08VSy Sxx08R CURRENT WVEFORM: Sinusoidal LOD: Resistive or Inductive CONDUCTION NGLE: 180 FREE IR RTING Sxx08L 0.5 verage On-State Current [I T(VE) ] - mps Sxx08V 1.5 Note: xx = voltage, y = sensitivity Figure 11: Peak Capacitor Discharge Current Figure 12: Peak Capacitor Discharge Current Derating Peak Discharge Current (I TM ) - mps I TRM Normalized Peak Current Sensitive SCR Standard SCR 0.2 t W Pulse Current Duration (t w ) - ms Case Temperature ( ) - C Figure 13-1: Typical DC Gate Trigger Current with R GK vs. Junction Temperature for S6008xS2 Figure 13-2: Typical DC Gate Trigger Current with R GK vs. Junction Temperature for S6008xS3

7 Figure 14-1: Typical DC Holding Current with R GK vs. Junction Temperature for S6008xS2 Figure 14-1: Typical DC Holding Current with R GK vs. Junction Temperature for S6008xS3 Figure 15-1: Typical Static dv/dt with R GK vs. Junction Temperature for S6008xS2 Figure 15-2: Typical Static dv/dt with R GK vs. Junction Temperature for S6008xS3 Figure 16-1: Typical turn off time with R GK vs. Junction Temperature for S6008xS2 Figure 16-2: Typical DC Gate Trigger Current with R GK vs. Junction Temperature for S6008xS3

8 Temperature Figure 17: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive)On-state Current (I TSM ) mps 10 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOD: Resistive RMS On-State Current: [I T(RMS) ]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value Surge Current Duration -- Full Cycles Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Pre Heat - Temperature Max (T s(max) ) 200 C - Time (min to max) (t s ) secs verage ramp up rate (Liquidus Temp) (T L ) to peak 5 C/second max T L T S(max) T S(min) Preheat t L Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max t S - Temperature (T L ) (Liquidus) 217 C Reflow - Temperature (t L ) seconds Peak Temperature (T P ) /-5 C 25 time to peak temperature Time Time within 5 C of actual peak Temperature (t p ) seconds Ramp-down Rate 5 C/second max Time 25 C to peak Temperature (T P ) 8 minutes Max. Do not exceed 280 C

9 Physical Specifications Environmental Specifications Terminal Finish Body Material Lead Material Design Considerations % Matte Tin-plated UL recognized epoxy meeting flammability rating 94V-0 Copper lloy Careful selection of the correct component for the application s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Test C Blocking Temperature Cycling Temperature/ Humidity High Temp Storage Low-Temp Storage Resistance to Solder Heat Solderability Lead Bend Specifications and Conditions MIL-STD-750, M-1040, Cond pplied Peak C 125 C for 8 hours MIL-STD-750, M-1051, cycles; -40 C to +150 C; 15-min dwell-time EI / JEDEC, JESD hours; 320V - DC: 85 C; 85% rel humidity MIL-STD-750, M-1031, 8 hours; 150 C 8 hours; -40 C MIL-STD-750 Method 2031 NSI/J-STD-002, category 3, Test MIL-STD-750, M-2036 Cond E

10 Dimensions TO-220B (R-Package) Non-Isolated Mounting Tab Common with Center Lead E NODE MESURING POINT O P RE (REF.) 0.17 IN 2 Inches Millimeters Dimension Min Max Min Max B C D B C D E G F L H R NOTCH IN GTE LED TO ID. NON-ISOLTED TB F G H J K CTHODE NODE K J GTE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). L M N O P R Dimensions TO-220B (L-Package) Isolated Mounting Tab E MESURING POINT RE (REF.) 0.17 IN 2 O P Inches Millimeters Dimension Min Max Min Max B C D B C D E F F G G L H R H J K CTHODE NODE K J GTE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). L M N O P R

11 Dimensions TO-251 (V/I-Package) V/I-PK Through Hole node E D MESURING POINT H J RE: IN Inches Millimeters Dimension Min Typ Max Min Typ Max B B C D E C P Q R S K F G H I J Cathode node GTE I G F L K L P Q R S Dimensions TO-252 (D-Package) D-PK Surface Mount node B E D MESURING POINT Dimension Inches Millimeters Min Typ Max Min Typ Max B C Cathode node I G P Q GTE F RE: IN C D E F G O L M N K J H H I J K L M N O P Q

12 Product Selector Voltage Part Number 400V 600V 800V 0V Gate Sensitivity Type Package Sxx08RS2 X X 0.2m Sensitive SCR TO-220R Sxx08LS2 X X 0.2m Sensitive SCR TO-220L Sxx08VS2 X X 0.2m Sensitive SCR TO-251 Sxx08DS2 X X 0.2m Sensitive SCR TO-252 Sxx08RS3 X X 0.5m Sensitive SCR TO-220R Sxx08LS3 X X 0.5m Sensitive SCR TO-220L Sxx08VS3 X X 0.5m Sensitive SCR TO-251 Sxx08DS3 X X 0.5m Sensitive SCR TO-252 Sxx08R X X X X 15m Standard SCR TO-220R Sxx08L X X X X 15m Standard SCR TO-220L Sxx08V X X X X 15m Standard SCR TO-251 Sxx08D X X X X 15m Standard SCR TO-252 Sxx08NS2 X X 0.2m Sensitive SCR TO-263 Sxx08NS3 X X 0.5m Sensitive SCR TO-263 Sxx08N X X X X 15m Standard SCR TO-263 Sxx08DS1 X 50µ Sensitive SCR TO-252 Sxx08DS4 X µ Sensitive SCR TO-252 Note: xx = Voltage/10 Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx08L/RyyTP Sxx08L/Ryy 2.2 g Tube 500 (50 per tube) Sxx08DyyTP Sxx08Dyy 0.3 g Tube 750 (75 per tube) Sxx08DyyRP Sxx08Dyy 0.3 g Embossed Carrier 2500 Sxx08VyyTP Sxx08Vyy 0.4 g Tube 750 (75 per tube) Sxx08L/RTP Sxx08L/R 2.2 g Tube 500 (50 per tube) Sxx08DTP Sxx08D 0.3 g Tube 750 (75 per tube) Sxx08DRP Sxx08D 0.3 g Embossed Carrier 2500 Sxx08NyyTP Sxx08Nyy 1.6g Tube 500 (50 per tube) Sxx08NyyRP Sxx08Nyy 1.6g Embossed Carrier 500 Sxx08VyyNTP Sxx08N 1.6g Tube 500 (50 per tube) Sxx08NTP Sxx08N 1.6g Embossed Carrier 500 Sxx08NRP Sxx08V 0.4 g Tube 750 (75 per tube) Note: xx = Voltage/10; yy = Sensitivity

13 TO-252 Embossed Carrier Reel Pack (RP) Specifications Meets all EI Standards (4.0) Gate DI (1.5) Cathode 0.63 (16.0) (13.3) * XXXXXX XX DC XXXXXX XX DC XXXXXX XX DC XXXXXX * Cover tape (8.0) node (13.0) rbor Hole Diameter (330.0) Dimensions are in inches (and millimeters) (16.3) Direction of Feed TO-202 Type 1 (F Package) TO-202 Type 1 (F Package) Part Numbering System COMPONENT DEVICE TYPE S: SCR VOLTGE RTING 40: 400V 60: 600V 80: 800V K0: 0V CURRENT RTING 08: 8 S L S2 56 S6008F1 yxxxx LED FORM DIMENSIONS xx: Lead Form Option SENSITIVITY & TYPE Sensitive SCR: SCR: Standard SCR: S1: S2: 50µ200µ {blank} 15m S2: S3: 200µ 500µ S3: Standard 500µ SCR: TO-220 B (blank): - (L and 15m S4: µ R Package) PCKGE TYPE L: TO-220 Isolated R: TO-220 Non-Isolated S6008RS2 V: YMXXX TO-251 (V/I-Pak) D: TO-252 (D-Pak) N: TO-263 (D 2 PK) Part Marking System TO (V Package) TO (D Package) S6008F1 S6008DS2 S6008DS2 YMLDD yxxxx Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code YMLDD TO-263 (N Package) TO-220 B - (L and R Package) S6008DS2 YMLDD Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code TO (V Package) TO (D Package) S6008DS2 YMLDD Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code S6008RS2 YMXXX Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code