NGD8205ANT4G. Ignition IGBT. 20 Amp, 350 Volt, N Channel DPAK. 20 A, 350 V V CE(on) = 1.3 I C = 10 A, V GE 4.5 V

Transcription

1 NGD25AN Ignition IGBT 2 Amp, 35 Volt, N Channel DPAK This Logic Level Insulated Gate Bipolar Transistor (IGBT) features monolithic circuitry integrating ESD and Overvoltage clamped protection for use in inductive coil drivers applications. Primary uses include Ignition, Direct Fuel Injection, or wherever high voltage and high current switching is required. Features Ideal for Coil on Plug and Driver on Coil Applications DPAK Package Offers Smaller Footprint for Increased Board Space Gate Emitter ESD Protection Temperature Compensated Gate Collector Voltage Clamp Limits Stress Applied to Load Integrated ESD Diode Protection Low Threshold Voltage for Interfacing Power Loads to Logic or Microprocessor Devices Low Saturation Voltage High Pulsed Current Capability Optional Gate Resistor (R G ) and Gate Emitter Resistor (R GE ) These are Pb Free Devices G Littelfuse.com 2 A, 35 V V CE(on) =.3 I C = A, V GE.5 V R G R GE C E Applications Ignition Systems MAXIMUM RATINGS (T J = 25 C unless otherwise noted) Rating Symbol Value Unit Collector Emitter Voltage V CES 39 V Collector Gate Voltage V CER 39 V Gate Emitter Voltage V GE 5 V Collector Current T C = 25 C Pulsed I C 2 5 A DC A AC Continuous Gate Current I G. ma Transient Gate Current (t 2 ms, f Hz) I G 2 ma ESD (Charged Device Model) ESD 2. kv ESD (Human Body Model) R = 5, C = pf ESD ESD (Machine Model) R =, C = 2 pf ESD V Total Power T C = 25 C Derate above 25 C. P D 25.3 kv W W/ C Operating & Storage Temperature Range T J, T stg 55 to +75 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. DPAK CASE 369C STYLE 7 MARKING DIAGRAM G YWW C NGD C 25xG E Y WW NGD25x x G = Year = Work Week = Device Code = A = Pb Free Package ORDERING INFORMATION NGD25ANTG 2 3 Device Package Shipping DPAK (Pb Free) 25/Tape & Reel Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. Publication Order Number: NGD25AN/D

2 NGD25AN UNCLAMPED COLLECTOR TO EMITTER AVALANCHE CHARACTERISTICS ( 55 T J 75 C) Characteristic Symbol Value Unit Single Pulse Collector to Emitter Avalanche Energy V CC = 5 V, V GE = 5. V, Pk I L = 6.7 A, R G =, L =. mh, Starting T J = 25 C V CC = 5 V, V GE = 5. V, Pk I L =.9 A, R G =, L =. mh, Starting T J = 5 C V CC = 5 V, V GE = 5. V, Pk I L =. A, R G =, L =. mh, Starting T J = 75 C Reverse Avalanche Energy V CC = V, V GE = 2 V, Pk I L = 25. A, L = 6. mh, Starting T J = 25 C THERMAL CHARACTERISTICS E AS 25 2 E AS(R) 2 mj mj Thermal Resistance, Junction to Case R JC.2 C/W Thermal Resistance, Junction to Ambient (Note ) R JA 95 C/W Maximum Temperature for Soldering Purposes, / from case for 5 seconds T L 275 C. When surface mounted to an FR board using the minimum recommended pad size. ELECTRICAL CHARACTERISTICS Characteristic Symbol Test Conditions Temperature Min Typ Max Unit OFF CHARACTERISTICS Collector Emitter Clamp Voltage BV CES I C = 2. ma T J = C to 75 C V I C = ma T J = C to 75 C Zero Gate Voltage Collector Current I CES V GE = V, V CE = 5 V Reverse Collector Emitter Clamp Voltage B VCES(R) V CE = 75 V, V GE = V I C = 75 ma Reverse Collector Emitter Leakage Current I CES(R) V CE = 2 V T J = 25 C.. A T J = 25 C.5.5 A T J = 75 C. 25 * T J = C.. 5. T J = 25 C V T J = 75 C * T J = C T J = 25 C ma T J = 75 C T J = C.3.25 Gate Emitter Clamp Voltage BV GES I G = 5. ma T J = C to 75 C V Gate Emitter Leakage Current I GES V GE = 5. V T J = C to 75 C * A Gate Resistor (Optional) R G T J = C to 75 C 7 Gate Emitter Resistor R GE T J = C to 75 C k ON CHARACTERISTICS (Note ) Gate Threshold Voltage V GE(th) I C =. ma, V GE = V CE Threshold Temperature Coefficient (Negative) *Maximum Value of Characteristic across Temperature Range. 3. Pulse Test: Pulse Width 3 S, Duty Cycle 2%. T J = 25 C V T J = 75 C.7..3 T J = C * mv/ C Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. 2 Publication Order Number: NGD25AN/D

3 NGD25AN ELECTRICAL CHARACTERISTICS Characteristic Symbol Test Conditions Temperature Min Typ Max Unit ON CHARACTERISTICS (Note ) Collector to Emitter On Voltage V CE(on) I C = 6.5 A, V GE = 3.7 V I C = 9. A, V GE = 3.9 V I C = 7.5 A, I C = A, I C = 5 A, I C = 2 A, Forward Transconductance gfs I C = 6. A, V CE = 5. V T J = 25 C V T J = 75 C T J = C..3. T J = 25 C T J = 75 C T J = C...5 T J = 25 C.5.5. T J = 75 C T J = C..3.6* T J = 25 C..3.6 T J = 75 C..5. T J = C...7* T J = 25 C T J = 75 C T J = C * T J = 25 C T J = 75 C.2.5. T J = C * T J = 25 C 25 Mhos DYNAMIC CHARACTERISTICS Input Capacitance C ISS 3 5 pf Output Capacitance C OSS f = khz, V CE = 25 V T J = 25 C 7 9 Transfer Capacitance C RSS 2 22 SWITCHING CHARACTERISTICS Turn Off Delay Time (Resistive) t d(off) T J = 25 C 6.. Sec VCC = 3 V, IC = 9. A T J = 75 C 6.. Fall Time (Resistive) t f R G =. k, R L = 33, V GE = 5. V T J = 25 C. 6.. T J = 75 C..5 Turn Off Delay Time (Inductive) t d(off) T J = 25 C VCC = 3 V, IC = 9. A T J = 75 C Fall Time (Inductive) t f R G =. k, L = 3 H, V GE = 5. V T J = 25 C T J = 75 C Turn On Delay Time t d(on) T J = 25 C VCC = V, IC = 9. A T J = 75 C Rise Time t r R G =. k, R L =.5, V GE = 5. V T J = 25 C. 6.. *Maximum Value of Characteristic across Temperature Range.. Pulse Test: Pulse Width 3 S, Duty Cycle 2%. T J = 75 C Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. 3 Publication Order Number: NGD25AN/D

4 NGD25AN TYPICAL ELECTRICAL CHARACTERISTICS SCIS ENERGY (mj) T J = 25 C T J = 75 C 5 V CC = V V GE = 5. V R G = 2 6 INDUCTOR (mh) I A, AVALANCHE CURRENT (A) L =. mh L = 3. mh L = mh V CC = V V GE = 5. V R G = 5 75 Figure. Self Clamped Inductive Switching Figure 2. Open Secondary Avalanche Current vs. Temperature I C = 25 A I C = 2 A I C = 5 A I C = A I C = 7.5 A I C, COLLECTOR CURRENT (A) V GE = V 5 V T J = 75 C V V 3.5 V 3 V 2.5 V Figure 3. vs. Junction Temperature Figure. Collector Current vs. I C, COLLECTOR CURRENT (A) V GE = V 5 V T J = 25 C.5 V V 3.5 V 3 V 2.5 V I C, COLLECTOR CURRENT (A) V GE = V 5 V T J = C.5 V V 3.5 V 3 V 2.5 V Figure 5. Collector Current vs. Figure 6. Collector Current vs. Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. Publication Order Number: NGD25AN/D

5 NGD25AN TYPICAL ELECTRICAL CHARACTERISTICS I C, COLLECTOR CURRENT (A) V CE = 5 V.5 T J = 25 C T J = 75 C T J = C COLLECTOR TO EMITTER LEAKAGE CURRENT ( A).. 5 V CE = 2 V V CE = 75 V V GE, GATE TO EMITTER VOLTAGE (V) Figure 7. Transfer Characteristics Figure. Collector to Emitter Leakage Current vs. Temperature GATE THRESHOLD VOLTAGE (V) Mean + Mean Mean C, CAPACITANCE (pf).. C iss C oss C rss Figure 9. Gate Threshold Voltage vs. Temperature Figure. Capacitance vs. SWITCHING TIME ( s) t fall t delay V CC = 3 V V GE = 5. V R G = I C = 9. A R L = 33 SWITCHING TIME ( s) V CC = 3 V V GE = 5. V R G = I C = 9. A L = 3 H t delay t fall Figure. Resistive Switching Fall Time vs. Temperature Figure 2. Inductive Switching Fall Time vs. Temperature Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. 5 Publication Order Number: NGD25AN/D

6 NGD25AN R(t), TRANSIENT THERMAL RESISTANCE ( C/Watt) Duty Cycle = D CURVES APPLY FOR POWER P (pk) PULSE TRAIN SHOWN. t READ TIME AT t Single Pulse t 2 T J(pk) T A = P (pk) R JA (t) DUTY CYCLE, D = t /t 2 For D=: R JC R(t) for t. s t,time (S) Figure 3. Minimum Pad Transient Thermal Resistance (Non normalized Junction to Ambient) R JC(t), TRANSIENT THERMAL RESISTANCE ( C/Watt). Duty Cycle = DUTY CYCLE, D = t Single Pulse /t P (pk) t,time (S) Figure. Best Case Transient Thermal Resistance (Non normalized Junction to Case Mounted on Cold Plate) t t 2 D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t T J(pk) T A = P (pk) R JC (t) Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. 6 Publication Order Number: NGD25AN/D

7 NGD25AN PACKAGE DIMENSIONS L3 L b2 e E b3 2 3 b A D B DETAIL A.5 (.3) M C c A DPAK (SINGLE GAUGE) CASE 369C ISSUE D C c2 H L2 GAUGE PLANE L L DETAIL A ROTATED 9 CW SOLDERING FOOTPRINT A H 3.. C Z SEATING PLANE NOTES:. DIMENSIONING AND TOLERANCING PER ASME Y.5M, CONTROLLING DIMENSION: INCHES. 3. THERMAL PAD CONTOUR OPTIONAL WITHIN DI- MENSIONS b3, L3 and Z.. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED.6 INCHES PER SIDE. 5. DIMENSIONS D AND E ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY. 6. DATUMS A AND B ARE DETERMINED AT DATUM PLANE H. INCHES MILLIMETERS DIM MIN MAX MIN MAX A A b b b c c D E e.9 BSC 2.29 BSC H L L. REF 2.7 REF L2.2 BSC.5 BSC L L.. Z STYLE 7: PIN. GATE 2. COLLECTOR 3. EMITTER. COLLECTOR SCALE 3: mm inches Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and shall not be used for, any purpose (including, without limitation, military, aerospace, medical, life-saving, life-sustaining or nuclear facility applications, devices intended for surgical implant into the body, or any other application in which the failure or lack of desired operation of the product may result in personal injury, death, or property damage) other than those expressly set forth in applicable Littelfuse product documentation. Warranties granted by Littelfuse shall be deemed void for products used for any purpose not expressly set forth in applicable Littelfuse documentation. Littelfuse shall not be liable for any claims or damages arising out of products used in applications not expressly intended by Littelfuse as set forth in applicable Littelfuse documentation. The sale and use of Littelfuse products is subject to Littelfuse Terms and Conditions of Sale, unless otherwise agreed by Littelfuse. Littelfuse.com Specifications subject to change without notice. 26 Littelfuse, Inc. December, 26 Rev. 7 Publication Order Number: NGD25AN/D