PROCESS CONTROL UNITS ESM-XX50

Transcription

1 Remote RAMP MAN AUTO PROESS TROL UNITS ESM-XX0 ESM-0, ESM-0, ESM-0, ESM-0, ESM-0 Unversal Input PID ontroller wth Smart I/O Module System - dgts process (P) ve dgts process set (S) dsplay - Unversal process nput(t, RTD, m,, ma ) - Optonal secondary sensor nput - Dual or mult pont calbraton for voltage & urrent nput - onfgurable /, P, PI, PD and PID control forms - Auto-tune and Self-tune PID - Manual/Automatc mode selecton for control outputs - Bumpless transfer - Motorzed valve control functon - Programmable heatng, coolng and alarm functons for control outputs - steps profle control ( Ramp & Soak ) functon and start-holdstop by usng logc nput module -Remote set pont functon by usng analogue nput modules - Re-Transmsson - Detecton of heater falure by usng 0... A T nput module - Smart I/O module system - RS-232 (standard) or RS- (optonal) seral communcaton wth Modbus RTU protocol SPEIFIIS: Inputs Unversal Input: Unversal nput, T, RTD, oltage/urrent Thermocouple (T) : L(DIN 3),J, K, R, S, T, B, E ve N (IE.)(ITS0), (ITS0) Thermoresstance (RTD): PT-0 (IE)(ITS0) Input : m,, ma Measurement Range: Please refer to Table- for selecton of nput type and scala. Accuracy: ± 0,2% of full scale for thermocouple, thermoresstance and voltage old Juncton ompensaton: Automatcally ± 0./. Lne ompensaton: Maxmum Ohm Sensor Break Protecton: Upscale Samplng ycle: 3 samples per second Input Flter : 0.0 le 00.0 seconds TROL ontrol Forms: Programmable /, P, PI, PD or PID. OUTPUT Standard Relay : A@20 (Programmable control or alarm output) (Electrcal Lfe : Operaton (Full Load)) Modules -Relay Module - SSR Drver Module (Max.mA@ ) - Dgtal (Transstor) Module (Maks.0 ) -0/... ma urrent Module Input Modules -Dgtal Input Module -0/... ma urrent Input Module -0...A T Input Module -T or 0...0m Input Module -PT-0 Input Module Input Module oltage 0-20 (-%;+%) -A 2 (-% ; +%)-A or 2 (-% ; +%)-W ( oltage must be determned n order.) INDIORS Indcators : ESM-0 and ESM-0 :. mm Red dgt LED Dsplay ESM-0 and ESM-0 :.2 mm Red dgt LED Dsplay ESM-0 : mm Red dgt LED Dsplay Setpont Indcators : ESM-0, ESM-0 and ESM-0 : mm Green djt LED Dsplay ESM-0 :. mm Green djt LED Dsplay ESM-0 :. mm Green djt LED Dsplay LED Indcators : (Auto Tunng), S(Set alue), Man(Manuel Operaton),Auto(Auto Operaton), /2/3 ( status Leds),,,, Ramp and Remote LEDs Envronmental Ratngs and Pyhscal Spesfcatons Operatng Temperature: Max. Operatng Humdty : 0-0%RH (non-condensng) Protecton lass : NEMA X (IP at front, IP at rear). Weght: ESM-0 : 2 gr. ESM-0 : gr. ESM-0 : gr. ESM-0 : 30 gr. ESM-0 : gr. Dmensons: ESM-0 : ( x mm, Depth : mm) ESM-0 : ( x mm, Depth :. mm) ESM-0 : (2 x 2mm, Depth :. mm) ESM-0 : ( x mm, Depth :. mm) ESM-0 : ( x mm, Depth :. mm) Panel ut-out ESM-0 : ( x mm) ESM-0 : (2 x mm) ESM-0 : ( x mm) ESM-0 : (2 x 2mm) ESM-0 : ( x 2mm) Electrcal onnectons T 2 Unversal Input MODULE- 0 to 0 m 0 to ESM-0 II T 2 3 Unversal Input MODULE- 0 to 0 m 0 to ESM-0 II 3 2 Sensor oltage MODULE-2 2 Sensor oltage MODULE-2 ontrol, or Logc N N A@20 N L A T ontrol, or Logc A@20 ommuncaton Module (RS-232(standart)/ RS-( optonal)) N L A T ommuncaton Module (RS-232(standart)/ RS-( optonal)) T 2 3 Unversal Input II MODULE - 0 to 0 m 0 to ESM-0 2 Sensor oltage MODULE - 2 T 2 3 Unversal Input II MODULE - MODULE to 0 m 0 to ESM-0 2 Maks.0mA Sensor oltage T 2 3 Unversal Input II MODULE - 0 to 0 m 0 to ESM-0 DIMENSIS S mm /. nch ontroller S 2 Sensor oltage MODULE - 2 ESM-0 ontroller 2mm / 2.3 nch mm /. nch. ± mm /0. nch ESM-0 2mm / 2.3 nch ontrol, or Logc N N A@20 N ontrol, or Logc A@20 ontrol, or Logc A@20. ± mm /0. nch. mm/. nch N L A T N L A T N L A T mm / 2. nch ontroller ESM - 0 REMOTE RAMP MAN AUTO mm / 3. nch S PANEL MOUNTING S ontroller mm / 3. nch S ontroller ESM-0 mm /. nch 2 ESM-0 mm / 3. nch 3 mm / 3. nch -Before mountng the devce n your panel, make sure that the cut-out s of the rght sze. 2-heck front panel gasket poston 3-Insert the devce through the cutout. If the mountng clamps are on the unt, put out them before nsertng the unt to the panel. -Insert the unt n the panel cut-out from the front sde. -Insert the mountng clamps to the holes that located top and bottom sdes of devce and screw up the fxng screws untl the unt completely mmoble wthn the Panel Introducton Brochure. ENG ESM-XX0 0 0 / mm/. nch. ± mm /0. nch mm / 2. nch. ± mm /0. nch mm / 2. nch. ± mm /0. nch mm / 2. nch

2 S S S S S S S S S S S S S S S S S S S S S S S S S Adjustment of Set alue Man Operaton Press menu hange set value wth ncrement and decrement s. Proses Set Ekraný Press menu to ext wthout savng Set value. Easy Access Dagram for Operator Parameters Man Operaton Screen Press menu for enterng to the operator parameters secton. Press /OK Operator Menu Enterng Screen Enter the password wth ncrement and decrement s Set LýSt: Set values Proses Set ()Unt - Set ()Unt -2 Set ()Unt onfrm the password wth /OK -3 Set ()Unt Run LýSt: Selecton of PID Tune and Operaton Form TUNE SELETIBy selectng one of the methods below, devce can determne the PID parameters. Devce operates accordng to the defned PID Auto tune (Lmt ycle Tunng) operaton Self tune (Step Response Tunng) operaton Auto-Self Tune Self Tune operaton s performed, f the condtons are realzed when power on frstly. In normal operaton, t controls the tune condtons n Auto Tune selecton whch explaned below. If any of the condtons s realzed, t performs the Auto Tune operaton AUTOMI TUNE SELETI Devce does not do (Lmt ycle Tunng) operaton Devce does (Lmt ycle Tunng) operaton Easy Access Dagram for Techncan Parameters Man Operaton Screen Press menu Press menu changng next Button Operator menu enterng screen Press /OK Not BUMPLESS TRANSFER Enter the password wth ncrement and decrement s onfrm the password wth /OK OPERI FORM SELETI Automatc:The devce automatcally calculates the %output Manual: %cutput rate can be controlled manually by usng drecton s. Ramp/Soak ontrol Ramp/Soak functon s deactvated Ramp/Soak functon s actve Ramp/Soak functon s holdng. Real tme s stopped MOTORIZED ALE TROL Motorzed valve control s deactve Motorzed valve runs wth heatng PID functon. Motorzed valve runs wth coolng PID functon. output value n manual control s not taken nto consderaton whle passng from manual control to automatc control. New control output that s measured n automatc control s appled to process output. Last %output value s taken output value of manual control and manual control contnues whle passng from automatc control to manual control Whle passng from manual control to automatc control, last process output value n manual control s accepted as frst process output value n automatc control and automatc control contnues to run. Last % process output value n automatc control s accepted as process output value of manual control and manual control contnues to run. ALARM LH ANELING latch cancelng s not performed. If there s an alarm output wth latchng and there s no alarm status, latchng operaton wll be fnshed by the devce. When t s fnshed, ths parameter becomes Automatcally dýsp LýSt: Functon Selecton for Top and Bottom Dsplay It defnes the functon of the top dsplay. Ths parameter determnes whch value s shown n top dsplay. value (P) s shown n top dsplay Result of subtracton of process set value from process value (S-P) s shown n top dsplay If one of the analogue nput modules s plugged n or socket, measured value from ths module nput s shown n top dsplay. It defnes the functon of the bottom dsplay Ths parameter determnes whch value s shown n bottom dsplay. set value (S) s shown n bottom dsplay. % value that s appled to process control output s shown n bottom dsplay. Status of the Ramp/Soak functon s shown n bottom Dsplay. If one of the analogue nput modules s plugged n or socket, measured value from ths module nput s shown n top dsplay. If T nput module (EMI-) s plugged n or socket, measured value from ths module nput s shown n bottom dsplay. rmp SoA: onfguraton of RAMP/SOAK Functon and Step alues Soft-Start parameter Proses deðer, chaz enerjlendðnde set deðerne bu parametrede tanýmlanan süre sonunda erþr. Ramp Soak tolerans parametres (%0;%0 Skala)Brm Ramp/Soak þlemnde, proses deðernn artý veya eks yönde bu parametre le tanýmlanan toleransýn dýþýna çýkmasý durumunda zaman durdurulur. Ramp/Soak program step selecton parameter..program - steps 2.program - steps Steps between - s used as one program. Ramp/Soak step set value. For ramp operaton ; process value reaches to step set values that are defned wth these parameters at the end of the tme that are defned n ramp tme parameters. For soak operaton ; process value s constant n step set value that are defned n these parameters for tme that are defned n soak tme parameters. Ramp/Soak step set values can be adjusted from mnmum value of set scale to maxmum value of set scale. Ramp tme for Ramp/Soak value reaches to step set values at the end of the tme that are defned n these parameters. Soak tme for Ramp/Soak value s constant n step set value for tme that are defned n these parameters. PýnP onf: Input Type and Relevant Parameters wth Input Defnes the process nput T nput type selecton RTDnput type selecton oltage/urrent nput type selecton. Defnes type and scale of the thermocouple for T nput. It s actve f T nput type s selected L (-0;0) or (-;2) L (-0.0;0.0) or (-.0;.) J (-0;00) or (-32;2) J (-.;00.0) or (-.;.) K (-0;00) or (-32;232) K (-.;.) or (-.;.) R (0;0) or (32;302) R (0.0;.) or (32.0;.) S (0;0) or (32;302) S (0.0;.) or (32.0;.) T (-0;00) or (-32;2) T (-.;00.0) or (-.;2.0) B (;0) or (;3) B (.0;.) or (.0 ;.) E (-0;00) or (-23;2) E (-0.0;00.0) or (-.;.) N (-0;00) or (-32;232) N (-.;.) or (-.;.) (0;2300) or (32;3) (0.0;.) or (32.0;.) Defnes type and scale of sensor for RTD nput. It s actve f RTD nput PT-0 ( -0 ; 0 ) or ( -32 ; 02) PT-0 ( -. ; 0.0 ) or ( -. ;.) oltage / urrent Input Selecton Ths parameter s actve f oltage / urrent s selected m ( - ; ) 0... ( - ; ) 0... ( - ; ) 0...mA ( - ; )...ma ( - ; ) Dsplay Pont Poston Ths parameter s actve f No pont Between frst and second dgts 0.0 Between second and thrd dgts 0.00 Between thrd and fourth dgts Dsplay alue Adjustment Type oltage / urrent s selected. Fxed dual pont dsplay adjustment. Dsplay adjustment low pont value s fxed to -, dsplay adjustment hgh pont value s fxed to. User can do dual pont dsplay adjustment wth tpol and tpoh. User can do defned dsplay adjustment ponts. Low Pont Dsplay adjustment (-, )Unt Actve f oltage / urrent nput s selected. Hgh Pont Dsplay adjustment (-, )Unt Actve f oltage / urrent nput s selected. Dsplay adjustment ponts (-, )Unt Ths parameter s actve f oltage / urrent s selected. In mult pont dsplay adjustment operaton, defned scale s dvded nto adjustment ponts. For example : s (0-0 m ).

3 Po Po Po Po Po Po Po Po0 Po0 Po0 Po0 Po0 Po0 Po03 Po02 Po0 Po00 = 0 Set value m range are dvded nto egual parts. Every Poxx value s defned 0 / = 3. m range. oeffcent value (.000,.) value s multpled wth ths value. Actve f oltage / urrent nput s selected. Unt selecton Unt Unt Unt s oltage. Actve f oltage / urrent nput s selected No unt. Actve f oltage / current nput s selected Operatng Scale Mnmum alue (Scale Low Pont, Scale Hgh Pont)Unt Used for Proportonal band calculaton and dsplay blnk. Operatng Scale Maxmum alue (Scale Low Pont, Scale Hgh Pont)Unt Used for Proportonal band calculaton and dsplay blnk. m Dsplay offset for process value (Scale -%, Scale +%)Unt Ths parameter value s added to the process value. Flter Tme (0.0, 00.0)Second Defnes flter tme for dsplay value. old Juncton ompensaton Ths parameter s actve f process nput s selected T nput. old juncton compensaton s actve. old juncton compensaton s not actve. Scale: The dfference, between hgh pont and low pont of the process nput type. Example: If tsl = 2 (low pont s -0, hgh pont s 00), then scale s 0. If nput type s oltage/urrent, then the scale s dfference between tpoh and tpol parameters. Pýd onf: PID onfguraton Parameters PROPORTIAL BAND (0.0,.)% If = 00, = 0 and = 0.0 then Proportonal Band = ( - ) * / 0.0 Proportonal Band = (00-0)*0.0/0.0 = 00 INTEGRAL TIME (0, 300)Second an be changed by the user. After complated the tunnng correctly, ntegral tme value changes automatcally. If t s 0, ntegral control s deactvated. DERIIE TIME (0.0,.)Second an be changed by the user. After complated the tunnng correctly, ntegral tme value changes automatcally. If t s 0, dervatve control s deactvated. TROL PERIOD TIME (, 0) Second output perod tme MINIMUM TROL OUTPUT (0.0, )% Even as a result of the PID calculaton devce calculates the %output value less than ths parameter, heatng or coolng output s actve mnmum for OLL parameter. 0 MAXIMUM TROL OUTPUT (, 0.0)% Even as a result of the PID calculaton devce calculates the % output value greater than ths parameter, heatng or coolng output s actve maxmum for OUL parameter. HEING MINIMUM TROL OUTPUT TIME(0.0, Heatng output can not be actve less than ths parameter. Even f ths parameter s 0, ths parameter s accepted 0 msecs for securty. SOÐUTMA ORANSAL BAND KSAYISI (0.0, 0.0) )sec If heatng and coolng PID s used n a system, tune operaton s performed by heatng output.oolng proportonal parameter s calculated wth heatng proportonal band value and coeffcent(p- L = P-Ht * oe / 0.0) OOLING PROPORTIAL BAND ( 000.0%,.% ) If = 00, = 0 and = 0.0 se Proportonal Band = ( - ) * / 0.0 Proportonal Band = (00-0)*0.0/0.0 = 00 OOLINGINTEGRALTIME (0000 sec, 300 secs) It can be changed by the user. When tune operaton fnshes, t can be changed by the devce. If t s 0, ntegral control part does not perform. OOLINGDERIIE TIME (000.0 sec,. secs) It can be changed by the user. When tune operaton fnshes, t can be changed by the devce. If t s 0, dervatve control part does not perform. When tune operaton fnshes f ths parameter s 0, t can not be changed because dervatve control part does not perform. OOLING OUTPUT PERIOD TIME ( sec, 0 secs) It s control perod of coolng output. OOLING MINIMUM TROL OUTPUT( 0.0, )% It s % of coolng mnmum output. If heatng and coolng PID control functons operate together, ths parameter s not consdered. Even as a result of the coolng PID calculaton devce calculates the output value less than ths parameter, coolng output s actve mnmumor OLL parameter. OOLING MAXIMUM TROL OUTPUT (,0.0)% It s%of coolng maxmum output. Even as a result of the coolng PID calculaton devce calculates the output value greater than ths parameter, coolng output s actve maxmum foroulparameter. OOLING MINIMUM TROL OUTPUT ( 0.0%, ) oolng output can not be actve less than ths parameter. Even f ths parameter s 0, ths parameter s accepted 0 msecs for securty. ANTI-RE WINDUP ( 0-SALE HIGH POINT)UNIT Whle PID operaton s runnng f - <= process value <= + condton s true, ntegral value s calculated. If the condton s not true, ntegral value s not calculated and last calculated ntegral value s used. ALUE ((- SALE HIGH POINT / 2), (SALE HIGH POINT / 2) )Unt + s used as set value n PID calculatons. Ths parameter s used for shftng the proportonal band. PID OUTPUT (FOR HEING PID 0.0, 0.0)% (FOR OOLING PID -0.0, 0.0)% (FOR HEING&OOLIND PID : -0.0, 0.0)% Ths parameter s added to % whch s calculated at the end of the PID. OUTPUT RELED TO PID (FOR HEING PID 0.0, 0.0)% (FOR OOLING PID -0.0, 0.0)% (FOR HEING&OOLIND PID : -0.0, 0.0)% Ths parameter s added to the %process output that s calculated at the end of the PID accordng to process set value * / ( - ) PROESS ALUE STABILIZI (, SALE HIGH POINT)Unt It s used for controllng f process value oscllates or not when Parameter s or If; - <= alue <= + condton s not true, then devce start tunn operaton SALE LOW POINT : Mnmum process nput value n and Tc nputs. - for fxed dual pont dsplay adjustment used nputs, Scale low pont s the lowest one from or for selectable dual pont dsplay adjustment used nputs Scale low pont s the lowest one from or for mult pont dsplay adjustment used nputs SALE HIGH POINT : Maxmum process nput value n and Tc nputs. for fxed dual pont dsplay adjustment used nputs, Scale hgh pont s the bggest one from or for selectable dual pont dsplay adjustment used nputs Scale hgh pont s the bggest one from or for mult pont dsplay adjustment used nputs PROPORTIAL BAND SHIFTING ((- SALE HIGH POINT / 2 ), ( SALE HIGH POINT / 2 ) )Unt If coolng functon s performed ; oolng process set value s calculated by addng set value Wth parameter ontrol form can be / or PID. If set value for heatng = + ; Then set value for coolng = + + SENSOR BREAK OUTPUT ALUE (FOR HEING PID 0.0, 0.0)% (FOR OOLING PID -0.0, 0.0)% When sensor breaks, controllng of the process can contnue by enterng %output value to parameter. If ths parameter 0.0, process control output does not perform an output when sensor breaks. ýop onf: MODULE- onfguraton Parameters These parameters are actve f EMO-00 (Relay ), EMO- (SSR Drver) or EMO- (Dgtal ) module s plugged n socket. Defnes output functon for Heatng oolng Logc output It s actve f output functon of s heatng or coolng. / PID Hysteress value for OUT-. It can be adjusted from 0% to 0% of defned scale. ( It s actve f / control s selected. ) It determnes operaton form of hysteress. ( / ) S + /2 and S - /2 S and S+ or S and S- In / operaton, ths tme must be passed for the output to be logc output functon of output module n It s actve f output functon of s Lout (Logc ) output Manual /Automatc data output Sensor break alarm output s actve when the process value s out of the band whch s defned wth mnmum value of operatng scale And maxmum value of operatng scale ndcates that Ramp/Soak functon has fnshed Sensor break alarm output for analogue nput module n socket. ( It s vsble f one of analogue nput modules s plugged n socket ) If process value s less than mnmum value of operatng scale for analogue nput module n socket or greater than maxmum value of operatng scale for analogue nput module n socket, process output becomes actve.(ths parameter s vsble f one of the analogue nput modules s plugged n socket) Measurement nput selecton for alarm output. Ths parameter s vsble f Logc output functon of s output and one of the analogue nput modules s plugged n socket output runs accordng to the process nput. output runs accordng to the analogue nput module (2nd sensor nput) n socket MODULE- alarm It determnes alarm type. It s actve f logc output functon of s an alarm output. hgh alarm Devaton hgh alarm Devaton low alarm Devaton band alarm. Devaton range alarm Heater falure alarm. It s actve f T nput module s plugged n socket. MODULE- - hysteress value. It s actve f logc output functon of s an alarm output. on delay tme (0, )Seconds It s actve f logc output functon of s an alarm output off delay tme (0, )Seconds off delay tme. It can be adjusted from 0000 to seconds.when the value s greater than, s seen on the dsplay. It means alarm latchng output s selected. ýop onf: MODULE- onfguraton Parameters These parameters are actve f EMO-x30 (0/... ma Akým Çýkýþ) m module s plugged n socket. onfguraton of analogue output module n odule- 0...mA output s selected...ma output s selected Functon selecton of analogue output module n socket. Heatng oolng. Re-transmsson MODÜL- re-transmsson functon (It s actve f re-transmsson functon s selected for analogue output module n socket It retransmts value to analogue output. dfference of the process value and the set value It retransmts Set value to analogue output. ýop onf: MODULE- onfguraton Parameters These parameters are actve f EMI-00 (Dgtal Input) plugged n socket. onfguraton of dgtal nput n socket. Manual /Automatc selecton nput Auto Tune ( Lmt ycle Tunng ) Start/Stop nput. Ramp&Soak Start/Stop nput. Ramp&Soak Start/Hold nput. Latch ancelng.

4 ýop onf:module- onfguraton Parameters These parameters are actve f EMI- (0/...mA current Input), EMI-30 (T or 0...0m Input), EMI X0 (PT-0 Input) or EMI-0 (0... Input) module s plugged n onfguraton of analogue nput module n socket. T nput type selecton. Ths must be selected f analogue nput module n socket s EMI-30. PT-0 nput type selecton. Ths must be selected, f analogue nput module n socket s EMI-0. oltage / urrent nput type selecton. Ths must be selected f analogue nput module n socket s EMI-, EMI-30 or EMI - 0. MODULE-T nput module n sensor type selecton It s actve f nput type of s selected T. L (-0;0) or (-;2) L (-0.0;0.0) or (-.0;.) J (-0;00) or (-32;2) J (-.;00.0) or (-.;.) K (-0;00) or (-32;232) K (-.;.) or (-.;.) R (0;0) or (32;302) R (0.0;.) or (32.0;.) S (0;0) or (32;302) S (0.0;.) or (32.0;.) T (-0;00) or (-32;2) T (-.;00.0) or (-.;2.0) B (;0) or (;3) B (.0;.) or (.0 ;.) E (-0;00) or (-23;2) E (-0.0;00.0) or (-.;.) N (-0;00) or (-32;232) N (-.;.) or (-.;.) (0;2300) or (32;3) (0.0;.) or (32.0;.) MODULE- PT-0 nput module n sensor type selecton It s actve f nput type of s selected PT-0 PT-0 ( -0 ; 0 ) or ( -32 ; 02) PT-0 ( -. ; 0.0 ) or ( -. ;.) MODÜL- oltage/urrent Input Module Selecton It s actve f nput type of s selected oltage/urrent 0...0m ( - ; ) 0... ( - ; ) 0... ( - ; ) 0...mA ( - ; )...ma ( - ; ) pont poston for dsplay.it s actve f nput type of s selected oltage /urrent. No pont albraton type.it s actve f nput type of s selected oltage /urrent. Fxed dual pont calbraton s performed. Mnmum value of calbraton s - and maxmum value of calbraton s. Selectable dual pont calbraton s performed. Defnes mnmum value for selectable dual pont calbraton..it s actve f nput type of s selected oltage /urrent. Defnes maxmum value for selectable dual pont calbraton..it s actve f nput type of s selected oltage /urrent. Unt selecton Unt s Unt s Unt s U. No unt. Mnmum value of operatng scale (Low Lmt). It can be changed accordng to analogue nput type and scale. Maxmum value of operatng scale (Hgh Lmt). It can be changed accordng to analogue nput type and scale Dsplay offset for value n analogue nput module. It can be adjusted from -% to +% of scale. Ths value s added to the process value. It s flter tme for nput sgnal. It can be adjusted from 0.0 to 00.0 It decdes f cold juncton compensaton s actve or not for T nput module n socket. It s actve f process nput of s T nput. old juncton compensaton s actve old juncton compensaton s not actve It determnes f the measured value from analogue nput module n socket s used as Remote Set or not. Ths parameter s vsble f pont poston and unt parameters are same for process nput and analogue nput module. Measured value from analogue nput module n socket s used as process set value. User defned process set value s not consdered Measured value from analogue nput module n socket s not used as process set value. User defned process set value s consdered ýop onf: MODULE- onfguraton Parameters These parameters are actve f EMI-( T) Input Module s plugged n socket. urrent transfer rato for. It can be adjusted from 0 to 0. Example : For 0:A type current transformer ;Ths parameter must be tr= 0/ = ýop2 onf: MODULE-2 onfguraton Parameters All the functons that apply for module-, module-2 apples to. out3 onf: -3 onfguraton Parameters Defnes output functon for -3 Heatng oolng Logc output Defnes control algorthm of -3. It s actve f output functon of -3 s heatng or coolng / control algorthm PID control algorthm Hysteress value for OUT-3. It can be adjusted from 0% to 0% of defned scale. ( It s actve f / control s selected) It determnes operaton form of hysteress. ( It s actve f / control s selected) S+ /2 and S- /2 S and S+ or S and S- In / operaton, ths tme must be passed for the output to be energsed agan. ( It s actve f / control s selected) It determnes logc output functon of -3. It s actve f output functon of -3 s Lout(Logcoutput) output Manual /Automatc data output Sensor break alarm output P s actve when the process value s out of the band whch s defned wth mnmum value of operatng scale And maxmum value of operatng scale ndcates that Ramp/Soak functon has fnshed Sensor break alarm output for analogue nput module n or socket. ( It s vsble f one of analogue nput modules s plugged n or socket ) If process value s less than mnmum value of operatng scale or for analogue nput module n or socket or greater than maxmum value of operatng scale or for analogue nput module n or socket, process output becomes actve.(ths parameter s vsble f one of the analogue nput modules s plugged n or socket) Measurement nput selecton for -3 alarm output. Ths parameter s vsble f Logc output functon of -3 s output and one of the analogue nput modules s plugged n or socket output runs accordng to the process nput output runs accordng to the analogue nput module (2nd sensor nput) n or socket. It determnes alarm It s actve f logc output functon of -3 s alarm output. hgh alarm Devaton hgh alarm. Devaton low alarm. Devaton band alarm. Devaton range alarm Isýtýcý Arýzasý ý. It s actve f T nput module s plugged n or socket. - 3 hysteress value. (Scale 0%, scale 0%)Unt It s actve f logc output functon of -3 on delay tme(0, )Seconds It s actve f logc output functon of s alarm output. off delay tme (0, )Seconds When the value s than, s seen on the dsplay. It means alarm latchng output s selected. It s actve f logc output functon of -3 s alarm output. Types hgh alarm Set Set alue alue Types Devaton hgh alarm alue Devaton low alarm alue + Set alue alue - Set alue Devaton Band Devaton Range alue - Set alue - Set Gen onf: General Parameters alue alue alue alue + Set alue alue + Set Mnmum value for process set and alarm set values Maxmum value for process set and alarm set values alue 2. Sensor Set Pont Low Lmt.sensor scale mn. ) 2. Sensor Unt or socket Analog Input Modules. (If you have any of these parameters s observed) 2. Sensor Set Pont Hýgh Lmt.sensor scale mn. ) 2. Sensor Unt or socket Analog Input Modules. (If you have any of these parameters s observed) Whle the motor s completely off the valve fully open Whle the fully open or fully closed for the pass tme requred. alue between and 00 seconds can be entered. (If motorzed valve control s selected ths parameter s actve) The mnmum duraton of the valve motor drve output (0.,.0)% Ultt = 0 sec and = %.0 and the motor drvng the valve outlet. The mnmum tme to be actve n 0 *.0%= sec. (If motorzed valve control s selected ths parameter s actve) om onf: Parameters for onfguraton of Seral ommuncaton ommuncaton Accessng Address (,2) ommuncaton accessng address of devce. It can be adjusted from to 2. ommuncaton Baud Rate 00 Baud Rate. 200 Baud Rate. 00 Baud Rate 00 Baud Rate 00 Baud Rate

5 om onf: Parameters for onfguraton of Seral ommuncaton Falure Messages n ESM-XX0 ontrollers S S S Party Selecton for ommuncaton No party. Odd party. Even party. Stop Bt Selecton for ommuncaton stop bt 2 stop bt PASS onf: Operator and Techncan Passwords Operator Passwords (0, ) It s used for accessng to the operator parameters. If t s ; no password protecton whle enterng to the operator Parameters. If t s dfferent from 0 and user wants to access to the operator parameters; - If user does not enter password correctly : It turns to operaton screen wthout accessng to parameters. 2- When n top dsplay and n bottom dsplay are seen, f user presses wthout enterng Password (For observng the parameters): Operator can see operator menus and parameters but operator can not change the parameters Techncan Passwords(0, ) It s used for accessng to the techncan parameters. If t s no password protecton whle enterng to the techncan Parameters. If t s dfferent from 0 and user wants to access to the techncan parameters; - I f user does not enter password correctly : It turns to operaton screen wthout accessng to parameters. : When n top dsplay and n bottom dsplay are seen, f user presses wthout enterng Password (For observng the parameters): Operator can see operator menus and parameters but operator can not change the parameters. - Sensor falure n analogue nputs. Sensor connecton s wrong or there s no sensor connecton. 2- If parameter n Dsp Lst menu s and analogue nput module s plugged n Module- or socket, ths s sensor falure of analogue nput module. Sensor connecton s wrong or there s no sensor connecton. 3-If parameter s and parameter s and analogue nput module s plugged n Module- or socket, ths s sensor falure of analogue nput module. Sensor connecton s wrong or there s no sensor connecton. S S S S S S S - If top dsplay blnks : If analogue nput value s less than mnmum value of operatng scale top dsplay starts to blnk. - If top dsplay blnks : If analogue nput value s greater than maxmum value of operatng scale top dsplay starts to blnk. - If operator or techncan password s dfferent from 0 and user accesses to the parameter by Set wthout enterng the operator or techncan password and wants to change a parameter, the warnng message s shown on the bottom dsplay as shown on the left. Devce does not allow to do any changes wthout enterng the password correctly. - If tunng operaton can not be completed n hours, led starts to blnk.blnkng can be canceled by pressng Enter. -If user does not do anythng for 0 seconds whle devce s on operator or techncan menus, devce turns to operaton screen. - The devce s powered up, the normal does not begn to run, and the bottom of the screen As the sde flashng; and slots, EMIX EMI-X30, X0-EMI, EMI-X0 Analog nput modules nstalled at the same tme the event occurs. The unt normal to return to work, the devce energy cut-off and Analog Input one of the modules must be removed. - When power s on ; not startng the normal operaton and blnkng the bottom dsplay as shown on the left; It appears when two analogue nput modules ( EMI-, EMI-30,EMI-0, EMI-0 ) are plugged n and socket at the same tme. For startng normal operaton power off and pull out one of the analogue nput modules. Installaton Before begnnng nstallaton of ths product, please read the nstructon manual and warnngs below carefully. In package, - One pece unt - Twopece mountng clamp - One pece nstructon manual A vsual nspecton of ths product for possble damage occured durng shpment s recommended before nstallaton. It s your responsblty to ensure that qualfed mechancal and electrcal techncans nstall ths product. If there s danger of serous accdent resultng from a falure or defect n ths unt, power off the system and seperate the electrcal connecton of the devce from the system. The unt s normally suppled wthout a power swtch or a fuse. Use power swtch and fuse as requred. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. Never attempt to dsassemble, modfy or repar ths unt. Tamperng wth the unt may results n malfuncton, electrc shock or fre. Do not use the unt n combustble or explosve gaseous atmospheres. Durng the equpment s putted n hole on the metal panel whle mechancal nstallaton some metal burrs can cause njury on hands, you must be careful. Montage of the product on a system must be done wth t s own fxng clamps. Do not do the montage of the devce wth napproprate fxng clamps. Be sure that devce wll not fall whle dong the montage. It s your responsblty f ths equpment s used n a manner not specfed n ths nstructon manual. Warranty EMKO Elektronk warrants that the equpment delvered s free from defects n materal and workmanshp. Ths warranty s provded for a perod of two years. The warranty perod starts from the delvery date. Ths warranty s n force f duty and responsbltes whch are determned n warranty document and nstructon manual performs by the customer completely. Mantenance Repars should only be performed by traned and specalzed personnel. ut power to the devce before accessng nternal parts. Do not clean the case wth hydrocarbon-based solvents (Petrol, Trchlorethylene etc.). Use of these solvents can reduce the mechancal relablty of the devce. Use a cloth dampened n ethyl alcohol or water to clean the external plastc case. Other Informatons Manufacturer Informaton: Emko Elektronk Sanay ve Tcaret A.Þ. Demrtaþ Organze Sanay Bölges Karanfl Sk. No: BURSA / TURKEY Phone : +0 0 Fax : +0 Repar and mantenance servce nformaton: Emko Elektronk Sanay ve Tcaret A.Þ. Demrtaþ Organze Sanay Bölges Karanfl Sk. No: BURSA BURSA / TURKEY Phone : +0 0 Fax : +0 Orderng Informaton ESM-0 ( x DIN / ) ESM-0 ( x DIN / ) A B D E / FG HI / ESM-0 ( 2x2 DIN Szes) ESM-0 ( x DIN / ) ESM-0 ( x DIN / ) / / D Seral ommuncaton 0 None RS RS- B Input Type(RTD) 3 PT 0, IE(ITS0) 0 PT 0, IE(ITS0) B Input Type( oltage and urrent) m ma... ma U W Z A oltage 0-20 (-%;+%) 0/0Hz 2 2 (-%;+%) 0/0Hz 2 (-%;+%) ustomer (Maxmum 20 (-%;+%))0/0Hz B Input Type Scale onfgurable(tablo-) Table- Product ode - EM-X00 EM-X E - () Relay (A@20 at Resstve Load) FG Product ode 00 None - 0 Relay Module EMO-X00 02 SSR Drver Module EMO-X 03 Dgtal (Transstor) Module EMO-X 0 urrent Module ( 0/... ma ) EMO-X30 0 Dgtal Input Module EMI-X00 0 0/... ma urrent Input Module EMI-X A T Input Module EMI-X T veya 0...0m Input Module EMI-X30 PT-0 Input Module EMI-X Input Module EMI-X0 HI Ürün Kodu 00 None - 0 Relay Module EMO-X00 02 SSR Drver Module EMO-X 03 Dgtal (Transstor) Module EMO-X 0 urrent Module ( 0/... ma ) EMO-X30 0 Dgtal Input Module EMI-X00 0 0/... ma urrent Input Module EMI-X A T Input Module EMI-X T veya 0...0m Input Module EMI-X30 PT-0 Input Module EMI-X Input Module EMI-X0 Table- B Input Type(T) Scale() Scale() L,Fe onst DIN3-0,0 -,2 L,Fe onst DIN3-0.0, ,. 23 J,Fe un IE.(ITS0) -0,00-32,2 2 J,Fe un IE.(ITS0) -., ,. 2 K,Nr N IE.(ITS0) -0,00-32,232 2 K,Nr N IE.(ITS0) -.,. -.,. 2 R,Pt%Rh Pt IE.(ITS0) 0,0 32,302 2 S,Pt%Rh Pt IE.(ITS0) 0,0 32,302 2 T,u un IE.(ITS0) -0,00-32,2 30 T,u un IE.(ITS0) -., ,2.0 3 B,Pt30%Rh Pt%Rh IE.(ITS0),0,3 32 B,Pt30%Rh Pt%Rh IE.(ITS0).0,..0,. 33 E,Nr un IE.(ITS0) -0,00-23,2 3 E,Nr un IE.(ITS0) -0.0, ,. 3 N,Ncrosl Nsl IE.(ITS0) -0,00-32,232 3 N,Ncrosl Nsl IE.(ITS0) -.,. -.,. 3, (ITS0) 0, ,3 3, (ITS0) 0.0,. 32.0,. Skala() Scale() -0,0-32,02 -.,0.0 -.,. Scale