1 Signs and symbols. 4 Installation 5 Active window 6 Commissioning Filter settings edali addressing. 6.4 Addressing. 7 General functions

Transcription

1

2 Table of contents 1 Sgns and symbols Changes ntroduced... wth masterconfigurator Introducton Installaton Actve wndow Commssonng Selectng... an nterface Optons Flter settngs edali addressng Testng... the nstallaton Addressng Testng... addressng Groupng... control gear Settng... scenes Savng... a project 25 7 General functons Searchng... for devces Changng... a devce name Creatng... a new group Changng... a group name Assgnng... a DALI devce to a group Assgnng... a DALI devce to more than one group Removng... a DALI devce from a group Deletng... a DALI devce Checkng... devce assgnment 31 8 Confguraton DALI... control gear Devce Type... 0: Control gear for fluorescent lamps Devce Type... 1: Control gear for emergency lghtng Devce Type... 2: Control gear for hgh-pressure dscharge lamps Devce Type... 3: Control gear for low-voltage halogen lamps Devce Type... 4: Control gear for phase dmmers Devce Type... 6: Control gear for LEDs Devce Type... 8: Control gear for colour converters Devce Type : Mult-devce types DALI... XC 211 2

3 8.2.1 Basc confguraton Confguraton... of operatng mode "MC" Status DALI... MC DALI... bascdim DGC Basc confguraton Room profles Devce-specfc... confguraton Status Lght sensor Moton sensor Remote control DALI... MSensor DALI MSensor (verson 2.0) DALI MSensor... (verson 1.5 and 1.7) DALI MSensor... (verson 1.3) DALI... TOUCHPANEL User-defned... confguraton Tunable Whte Factory settngs DALI... PS2 Standby DALI-Somfy... anmeo Interface Quck... test Tools Command... admnstrator DALI commands DSI commands Command... sequence Control... gear wzard Localsaton... wzard for DALI XC Frmware... update Further components DALI... Montor DALI... BusServer Appendx Confguraton... commands for DALI control gear DALI... commands Reset... values Document... verson 307 3

4 4

5 1 Sgns and symbols The followng characters and symbols are used n ths manual: 1. Indvdual steps n the nstructons are numbered. Sngle-step nstructons are ndcated by at the begnnng of the lne. After a step has been descrbed, a descrpton of the expected results wll follow. These results are ndcated by at the begnnng of the lne. Requrements whch need to be checked before carryng out a step are ndcated by. Indvdual notes can be recognsed by. In addton, notes are dentfed by the word. 5

6 2 Changes ntroduced wth masterconfigurator 2.10 New functons Integraton of DALI XC (More nformaton can be found here ) Localsaton wzard for DALI XC (More nformaton can be found here ) Integraton of LCAI TuWh Lnear (More nformaton can be found here ) 305 ) Enhancements Enhancement of DALI commands (More nformaton can be found here... New devce: DALI bascdim DGC (More nformaton can be found here ). Changes to exstng functons Content of Sectons "Locatng devces" and "Identfyng emergency lumnares" was revsed and combned n Secton "Checkng devce assgnment" (More nformaton can be found here ) Content of Secton "Devce Type 2: Control gear for hgh-pressure dscharge lamps" was extended wth new sectons "Devce-specfc confguraton" (More nformaton can be found here ) and "chronostep" (More nformaton can be found here ). Content of secton "Status" was revsed and extended (More nformaton can be found here ). 6

7 3 Introducton The masterconfigurator software s a confguraton and parametersaton program for DALI devces. Ths software can be used to set up a DALI control lne and confgure ndvdual control gear and control unts. Basc functons Addressng Groupng Settng scenes Parametersng DALI devces Confgurng DALI and DSI commands Creatng command sequences Testng nstallaton, addressng and functons The masterconfigurator software s desgned for onlne operaton. If DALI devces are confgured offlne, faults may occur. 7

8 4 Installaton Ths secton covers the system requrements for the masterconfigurator software and how the software s nstalled. System requrements In order to make full use of the functonalty of the masterconfigurator software, the followng are requred: Operatng system Wndows XP Wndows Vsta: only compatble wth DALI USB frmware verson 1.4 or hgher (August 2008) Wndows 7: only compatble wth DALI USB frmware verson 1.4 or hgher (August 2008); compatblty mode: Wndows XP (Servce Pack 3) The chapter Changng compatblty mode you can change the compatblty mode. Screen resoluton Mnmum XGA (1024 x 768 pxels) Communcaton USB or COM nterface 9 wll tell you how Table 1: System requrements For updated nstructons for DALI USB wth older frmware versons, please refer to Secton DALI BusServer > Updatng the frmware verson 304. Installng software 1. Double-clck the fle masterconfigurator_vxxx.exe. 2. Clck on Next. The setup wzard appears. 3. Follow the setup wzard steps. The masterconfigurator software s nstalled. The masterconfigurator software can be accessed by gong to Start > Programs > DALITools > masterconfigurator or va the shortcut on the desktop. 8

9 Changng compatblty mode The compatblty mode only has to be changed f Mcrosoft Wndows 7 s used as the operatng system. 1. On the desktop, rght-clck on the con. 2. Select menu tem Propertes. 3. Clck on the Compatblty tab. 4. Enable the Run program n compatblty mode checkbox. 5. In the dropdown lst, select Wndows XP (Servce Pack 3). 6. Clck OK. Compatblty mode has been changed. 9

10 5 Actve wndow After startng up, the software dsplays the actve wndow. The control gear and control unts can be parametersed and confgured here. Dependng on the functon, further sub-wndows wll be opened. Name Functon (1) Ttle bar Dsplays the name of the project fle currently open. (2) Menu bar Contans the Fle, Settngs, Commssonng, Tools and Vew menus. (3) Toolbar Contans cons for quck access to varous functons. You can show or hde the toolbar va menu tem Vew > Toolbar. (4) DALI devce tree dagram Dsplays the devces connected to the DALI control lne n a tree dagram. It s also possble to see whch group each devce belongs to. (5) Detal vew Dsplays the propertes of a devce that has been selected n the DALI devce tree dagram. The devces can be confgured and parametersed here. (6) Status bar Dsplays status nformaton and help text. You can show or hde the status bar va menu tem Vew > Status bar. Table 2: Actve w ndow 10

11 Toolbar The followng cons are found n the toolbar: Icon Functon Create a new project Open a project Save a project Prnt a project Locate Identfy Table 3: Toolbar A detaled descrpton of the Locate and Identfy functons can be found n Secton Checkng devce assgnment Changng the language The software user nterface can be dsplayed n German or Englsh. The language s changed as follows: 1. Select Vew. 2. Select language. A message appears ndcatng that the language wll only be changed after the program has been restarted. 3. Confrm the message by clckng on OK. 4. Restart the program. The software wll be started n the desred language. Showng/hdng advanced settngs Control gear and control unts can be confgured usng the masterconfigurator. The advanced settngs must be dsplayed n order to confgure addtonal parameters as well as the general settngs. The advanced settngs can be shown or hdden as follows: 1. Select Vew. 2. Show (enable) or hde (dsable) the Advanced settngs. The advanced settngs are shown/hdden n the detal vew. The advanced settngs must be enabled agan each tme the software s restarted. 11

12 6 Commssonng The masterconfigurator software allows the user to test the correct wrng of the DALI control lne, address the devces and defne group and scene settngs n fve easy steps. In order for these steps to be carred out, an nterface must frst be selected. Optonally, the devce search and the addressng can be narrowed down. 6.1 Selectng an nterface Use a DALI USB for exchangng data between the computer and the devces on the DALI control lne. For backward compatblty, DALI SCI2 can be used. DALI SCI s not supported. If the computer s already connected to the DALI control lne va an nterface, the masterconfigurator software automatcally detects the type of nterface and selects t for communcaton. However, the nterface may also be selected manually. Selectng an nterface manually 1. Connect the USB cable to the DALI USB and the computer on whch the masterconfigurator software s nstalled. 2. Connect the DALI USB to the DALI control lne. 3. Select Settngs > Select nterface The Select nterface pop-up wndow appears. 4. To use a USB nterface, select the USB rado button. 5. To use a COM nterface, select the COM rado button. 6. If a COM nterface s beng used, select the COM nterface from the drop-down lst. 7. Confrm the selecton by clckng on OK. The nterface has been selected. DALI BusServer starts automatcally. 12

13 If the masterconfigurator software detects that a DALI USB s connected, t automatcally checks the USB software verson. If t s older than the verson suppled wth the masterconfigurator software, t wll be updated automatcally. Ths update takes approxmately one mnute. 6.2 Optons Under Settngs > Optons the followng functons can be set: Flter settngs ed addressng Flter settngs Ths functon allows the user to narrow the devce search or addressng. Enablng the flter 1. Select Settngs > Optons. The Optons pop-up wndow appears. 2. Clck on the Flter tab. 3. Select the checkbox to nclude devces n the devce search and addressng. 4. Confrm the selecton by clckng on OK. Flter for the devce search and the addressng s enabled. Only those devces wth enabled checkboxes wll be ncluded n the devce search and the addressng. 13

14 6.2.2 edali addressng Up to 64 ed addresses can be assgned when addressng ed devces. The 64 ed addresses can be confgured to be assgned once per DALI control lne or once per devce class. Dsablng the opton 1. Select Settngs > Optons. The Optons pop-up wndow appears. 2. Clck on the ed addressng tab. 3. Dsable the checkbox. 4. Confrm the selecton by clckng on OK. The type of ed addressng has been changed. Ths change wll be appled when the system s next rentalsed (New ntalsaton). Both types of ed addressng are explaned n the followng examples. Example 1: Assgn ed address (0-63) only once enabled: The ed addresses are assgned once per DALI control lne. Example 2: Assgn ed address (0-63) only once dsabled: The ed addresses are assgned once per devce class. 14

15 Example 1: ed addresses assgned once per DALI control lne Devce class ed address Explanaton DALI MSensor: lght sensor ea 0 The frst of 64 ed addresses has been assgned on ths DALI control lne. DALI MSensor: moton sensor ea 1 The second of 64 ed addresses has been assgned on ths DALI control lne. DALI MSensor: remote control ea 2 The thrd of 64 ed addresses has been assgned on ths DALI control lne. DALI MC ea 3 The fourth of 64 ed addresses has been assgned on ths DALI control lne. Table 4: Example of ed addressng, opton enabled In ths example a total of four out of 64 ed addresses have been assgned. Another 60 ed addresses can stll be assgned on ths DALI control lne. 15

16 Example 2: ed addresses assgned once per devce class Devce class ed address Explanaton DALI MSensor: lght sensor ea 0 The frst of 64 ed addresses has been assgned to the "Lght sensor" devce class. DALI MSensor: moton sensor ea 0 The frst of 64 ed addresses has been assgned to the "Moton sensor" devce class. DALI MSensor: remote control ea 0 The frst of 64 ed addresses has been assgned to the "Manual control unts" devce class. DALI MC ea 1 The second of 64 ed addresses has been assgned to the "Manual control unts" devce class. Table 5: Example of ed addressng, opton dsabled In ths example only one of the 64 ed addresses has been assgned to each of the "Lght sensor" and "Moton sensor" devce classes. Another 63 ed addresses can stll be assgned to each devce class. Two of the 64 ed addresses have been assgned to the "Manual control unts" devce class. Another 62 ed addresses can stll be assgned to ths devce class. 16

17 6.3 Testng the nstallaton Ths functon allows the user to test the wrng of the nstallaton. Testng the nstallaton 1. Select Commssonng > 1. Test nstallaton. The Execute test pop-up wndow appears. 2. Enter an nterval between 1 and 10 seconds. 3. Clck on Start. The Start button changes nto the Stop button. Once the test s started, the mnmum level and maxmum level commands are sent alternately to all lumnares on the DALI control lne. 4. Clck on Stop to stop the test. 6.4 Addressng Addressng can be carred out usng the addressng wzard. There are generally two ways to address devces: New ntalsaton: all addresses and group membershps are deleted n the devces. The devces are then re-addressed. System extenson (address prevously unaddressed devces): a search s carred out for prevously addressed and unaddressed devces. Addressng for prevously addressed devces wll reman unchanged. The next avalable address s then assgned to devces whch have been recently added. In the event of system extenson, recently added devces cannot already have an address. Otherwse, duplcate addresses could be assgned, whch would lead to problems. 17

18 Addressng Requrements: Installaton test completed successfully. No lamp errors. Optonal: flter enabled. 1. Select Commssonng > 2. Address. The addressng wzard appears. 2. Select rado button New ntalsaton or System extenson (address prevously unaddressed devces). If no other optons are selected, the addresses are assgned at random. 3. To set other addressng optons, clck on Optons. Further optons appear. 18

19 4. To address lumnares specfcally n accordance wth the addressng plan usng the physcal selecton method, select Lumnares. The way n whch the physcal selecton method s carred out dffers from devce to devce and should therefore be taken from the documentaton specfcally for the devce n queston. Not all DALI control gear supports ths type of addressng. Before addressng, check whether the connected control gear supports the physcal selecton method. 5. To address control unts specfcally accordng to the addressng plan usng the physcal selecton method, select Control unts. Secton Specal notes on addressng control unts 20 contans nformaton on how control unts are addressed usng the physcal selecton method. 6. To address lumnares so that no reacton s vsble n the room, select Addressng wthout vsble reacton. If lumnares are addressed wth the physcal selecton method, the Addressng wthout vsble reacton functon s gnored. Addressng wthout vsble reacton s recommended f the rooms are already n use and the system s just beng extended. In the case of addressng wth a vsble reacton, the lumnare beng addressed goes to the maxmum level. 7. Clck on Next. Addressng s carred out n accordance wth the selected optons. Found devces are lsted n the pop-up wndow. The assgned address s shown n brackets, wth A standng for DALI address and ea for ed address. 19

20 8. As soon as the addressng s complete, a message appears. 9. Clck Done to ext the addressng wzard. Found devces are shown n the DALI devce tree dagram. Specal notes on addressng control unts Control unts such as the DALI MC or the DALI TOUCHPANEL must be addressed wth the physcal selecton method. 20

21 When addressng control unts, the user s prompted to press a key on the control unt to address the devce. Addressng the DALI MC 1. Press the key on the DALI MC twce ("double-clck"). The masterconfigurator software recognses the nput and assgns an ed address (ea) to t. 2. Repeat the process for all four DALI MC nputs. The ed addresses (ea) are assgned n the order n whch the keys on the DALI MC are pressed. Addressng the DALI TOUCHPANEL Press any key on the DALI TOUCHPANEL. The masterconfigurator software recognses the nput and assgns an ed address (ea) to t. A total of 64 addresses can be assgned on the DALI control lne. The ed addresses gven to the DALI MC and the DALI TOUCHPANEL do not reduce ths number. 21

22 6.5 Testng addressng Ths functon allows the user to test the addressng. Testng addressng 1. Select Commssonng > 3. Check addressng. The Execute test pop-up wndow appears. The number of addressed control gear elements s shown under Total of addressed control gear. 2. Enter an nterval between 1 and 10 seconds. 3. Clck on Start. The Start button changes nto the Stop button. Once the test s started, the maxmum level s sent to all lumnares n order. The correspondng address appears under Control gear to maxmum value wth address. 4. Clck on Stop to stop the test. 22

23 6.6 Groupng control gear Ths functon allows the user to group control gear. Up to 16 groups (0 15) are avalable. Groupng control gear 1. Select Commssonng > 4. Group control gear. The Group control gear pop-up wndow appears. The left-hand column lsts all the avalable control gear. The rght-hand column shows all the devces that are n the selected group. 2. Select the desred group (0 15) from the Group drop-down lst. 3. Optonally, select the Localse checkbox. The selected lumnare goes to the maxmum level. 4. Select the control gear n the left-hand column. 5. To add control gear to the group, clck on Add. The control gear s removed from the left-hand column. It s added to the selected group and appears n the rght-hand column. Removng control gear from a group 1. Select the control gear n the left-hand column. 2. Clck on Remove. The control gear s removed from the group and appears n the left-hand column. 23

24 6.7 Settng scenes Ths functon allows the user to confgure up to 16 scenes (0 15). Settng scenes Requrement: Devces assgned to the groups. 1. Select Commssonng > 5. Set scenes. The Set scenes pop-up wndow appears. 2. Select the desred scene (0 15) from the drop-down lst. All the followng settngs are defned for ths scene. 3. Select the checkbox to assgn an ntensty to all the lumnares n the group. 4. Enter a value between 0% and 100%. All the control gear n ths group mmedately go to the entered level. 5. Confrm the entry by clckng on OK. Settngs are saved for ths group. 6. To defne the settngs for the other scenes, repeat steps 2 to 5 for each scene. MASK means that the lumnares n ths group wll retan ther current ntensty when the relevant scene s recalled. 24

25 6.8 Savng a project Ths functon allows the user to save the commssonng n a *.dnc fle. 1. Select Fle > Save. The Save fle pop-up wndow appears. 2. Select a locaton for the fle. 3. Enter the fle name. 4. Clck on Save. The project s saved. -or1. In the toolbar, clck on. The Save fle pop-up wndow appears. 2. Select a locaton for the fle. 3. Enter the fle name. 4. Clck on Save. The project s saved. 25

26 7 General functons After addressng, the devces are dsplayed n the DALI devce tree dagram. If devces have already been assgned to a group (see Secton Groupng control gear 23 ), ths group s created automatcally and the devces are assgned to t. DALI devces can be assgned to more than one group at the same tme. Group membershp can be seen n the detal vew. 7.1 Searchng for devces Requrements: Installaton test completed successfully. No lamp errors. Optonal: flter enabled. 1. In the DALI devce tree dagram, rght-clck on the The context menu appears. con. 2. Select Search devces n the context menu. The search s carred out wth the addressng wzard. Found devces are lsted n the pop-up wndow. The assgned address s shown n brackets, wth A standng for DALI address and ea for ed address. 26

27 3. Once the search s fnshed, a message appears. 4. Clck Done to ext the addressng wzard. Found devces are shown n the DALI devce tree dagram. For more nformaton on the settng optons for the addressng wzard, please refer to Secton Addressng Changng a devce name 1. In the DALI devce tree dagram, rght-clck on the devce name to be changed. The context menu appears. 2. Select Rename n the context menu. 3. Change the devce name drectly n the DALI devce tree dagram. 4. Confrm the entry by pressng ENTER. The devce name s changed. -or1. In the DALI devce tree dagram, select the devce name to be changed. 2. Press F2. 3. Change the devce name drectly n the DALI devce tree dagram. 4. Confrm the entry by pressng ENTER. The devce name s changed. When a devce s renamed, the abbrevaton n brackets dsappears. Once the new name s confrmed, however, the abbrevaton automatcally reappears n the brackets. 27

28 7.3 Creatng a new group 1. In the DALI devce tree dagram, rght-clck on the The context menu appears. con. 2. Select Create new group n the context menu. The next free group s automatcally added to the DALI devce tree dagram. 7.4 Changng a group name 1. In the DALI devce tree dagram, rght-clck on the group name to be changed. The context menu appears. 2. Select Rename n the context menu. 3. Change the group name drectly n the DALI devce tree dagram. 4. Confrm the entry by pressng ENTER. The group name s changed. -or1. In the DALI devce tree dagram, select the group name to be changed. 2. Press F2. 3. Change the group name drectly n the DALI devce tree dagram. 4. Confrm the entry by pressng ENTER. The group name s changed. When a group s renamed, the abbrevaton n brackets dsappears. Once the new name s confrmed, however, the abbrevaton automatcally reappears n the brackets. 7.5 Assgnng a DALI devce to a group 1. In the DALI devce tree dagram, clck on the devce to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the devce to the approprate group. (Drag & Drop) The devce s removed from the group n whch t was prevously located and s added to the desred group. -or1. In the DALI devce tree dagram, rght-clck on the devce to be assgned to a group. 2. Hold down the rght mouse button. 3. Drag the devce to the approprate group. 4. Release the rght-hand mouse button. 5. Select Move. The devce s removed from the group n whch t was prevously located and s added to the desred group. 28

29 Secton DALI MSensor 02 > Effectve range DALI MSensor 02 to a group. 250 contans nformaton on how to assgn a Secton DALI MSensor (verson 1.5) > Effectve range 266 contans nformaton on how to assgn a DALI MSensor (verson 1.5 and lower) to a group. 7.6 Assgnng a DALI devce to more than one group One DALI devce can be assgned to multple groups. To do ths, the DALI devce s frst coped and then assgned to the desred groups. 1. In the DALI devce tree dagram, clck on the devce to be coped and assgned to a group. 2. Hold down the left mouse button. 3. In addton, hold down the CTRL key. 4. Drag the devce to the approprate group. The devce s coped. It s now n both groups. -or1. In the DALI devce tree dagram, rght-clck on the devce to be coped and assgned to a group. 2. Hold down the rght mouse button. 3. Drag the devce to the approprate group. 4. Release the rght-hand mouse button. 5. Select Copy. The devce s coped. It s now n both groups. 7.7 Removng a DALI devce from a group 1. Clck on the devce to be removed from a group. 2. Hold down the left mouse button. 3. Drag the devce to the con. The devce s removed from the group and appears once agan n the DALI devce tree dagram wthout a group. -or1. Rght-clck on the devce to be removed from a group. The context menu appears. 2. Select Remove devce from group n the context menu. The devce s removed from the group and appears once agan n the DALI devce tree dagram wthout a group. 29

30 7.8 Deletng a DALI devce 1. Rght-clck on the devce to be deleted. The context menu appears. 2. Select Delete from the context menu. A message appears, promptng for confrmaton that the selected devce should be deleted. 3. Confrm the acton by clckng on Yes. The devce s deleted from the DALI devce tree dagram. The devce's address s deleted. -or1. In the DALI devce tree dagram, select the devce to be deleted. 2. Press DEL. A message appears, promptng for confrmaton that the selected devce should be deleted. 3. Confrm the acton by clckng on Yes. The devce s deleted from the DALI devce tree dagram. The devce's address s deleted. 30

31 7.9 Checkng devce assgnment There are varous ways to check the devce assgnment to the physcally exstng groups. Icon Descrpton The Locate con can be used to determne where bus subscrbers are located or whch address they have. A sngle devce, a group or all the devces connected to the DALI control lne can be located. The type of locaton method depends on the devce. There are two types of method: vsual and acoustc. Vsual locaton: type of locaton n whch the address of a bus subscrber s used to vsually locate ths subscrber n the feld. A vsually located lumnare, for example, responds by swtchng to the maxmum level. A vsually located emergency lumnare, for example, responds by forwardng ts address as a bnary flashng pattern va the status LED. Acoustc locaton: type of locaton n whch the address of a bus subscrber s used to acoustcally locate ths subscrber n the feld. An acoustcally located sensor, for example, responds by beepng. The followng devces can be located: DALI control gear Specal note for control gear for emergency lghtng: Only ever one control gear element for emergency lghtng can be located. Locatng all of the devces connected to the DALI control lne s only possble wth the Identfy con. Input devces Sensors The Identfy con can be used to determne where an emergency lumnare wth a specfc DALI short address s located. If the functon s enabled, all of the emergency lumnares connected to the DALI control lne respond by forwardng ther address as a bnary flashng pattern va the status LED. The followng devces can be dentfed: DALI control gear for emergency lghtng Table 6: Optons for checkng devce assgnment 31

32 Tps & trcks If an con s hghlghted n grey n the toolbar, the functon s enabled. After checkng the devce assgnment, the functon used must be dsabled va the correspondng con. Otherwse the devces wll contnue to respond accordng to the respectve functon. To locate an ndvdual devce va the dagram. To locate a group va the con, select the correspondng devce n the DALI devce tree con, select the group n the DALI devce tree dagram. To locate all of the devces connected to the DALI control lne va the DALI devce tree dagram. con, select the con n the 32

33 Emergency lumnares forward ther address as a bnary flashng pattern va the status LED. For ths purpose, the address s converted nto a sx-dgt bnary number, whch s represented as a flashng pattern. The red LED stands for bnary number 0, the green LED for bnary number 1. The followng optons are avalable to users n order to convert a bnary number to a decmal number: EM PRO Ident.TOOL software: You can download ths software from Trdonc's homepage at: Servces Software. EM PRO addressng tool (Artcle number ) 33

34 8 Confguraton The masterconfigurator software can be used to confgure the followng devces: DALI control gear DALI MC DALI MSensor 249 DALI TOUCHPANEL DALI PS2 Standby DALI Somfy anmeo nterface 287 A devce that has been selected n the DALI devce tree dagram can be confgured n the detal vew. The followng functons are avalable n the upper part of the detal vew: Functon Descrpton Read The settngs stored n the devce are read and dsplayed n the detal vew. Save Changes are stored n the devce. Quck test The confguraton of the control gear can be tested n the Quck test pop-up wndow. A detaled descrpton of the quck test can be found n Secton Quck test Readdress The address of the devce s changed. If the desred address has already been assgned to another devce on the DALI control lne, the addresses of the two devces are swapped. For the swap to take place, however, at least one address must be free. Factory settngs The devce s reset to ts factory settngs. Not every control gear element supports ths functon. Table 7: General functons Not every devce supports all functons. Functons whch are not supported are greyed out. 34

35 The followng table contans nformaton about whch devces support whch functons: Devce Read Save Quck test Readdress Factory settngs Control gear for fluorescent lamps (DT 0) Control gear for emergency lghtng (DT 1) Control gear for hghpressure dscharge lamps (DT 2) Control gear for low-voltage halogen lamps (DT 3) Control gear for phase dmmers (DT 4) Control gear for LEDs (DT 6) Control gear for colour converters (DT 8) Mult-devce type (DT 255) DALI XC DALI MC DALI bascdim DGC DALI MSensor DALI TOUCHPANEL DALI PS2 Standby DALI-Somfy anmeo Interface Table 8: Overvew of functon optons 35

36 8.1 DALI control gear The masterconfigurator software can be used to confgure the followng DALI control gear elements: DALI control gear Devce Type 0 (DT 0): control gear for fluorescent lamps 39 Devce Type 1 (DT 1): control gear for emergency lghtng 70 Devce Type 2 (DT 2): control gear for hgh-pressure dscharge lamps Devce Type 3 (DT 3): control gear for low-voltage halogen lamps Devce Type 4 (DT 4): control gear for phase dmmers Devce Type 5 (DT 5): not supported Devce Type 6 (DT 6): control gear for LEDs 150 Devce Type 7 (DT 7): not supported Devce Type 8 (DT 8): control gear for colour converters Devce Type 255 (DT 255): mult-devce type Devce type unknown: The devce operatng mode s ncorrectly set for control gear whch s reported as Devce type unknown. Perform readdressng. The devce operatng mode of all devces connected to the DALI control lne s automatcally set to automatc detecton. -orgo to the Trdonc-specfc confguraton context menu n the Devce operatng mode tab and change the devce operatng mode to automatc detecton. 36

37 Confguraton usng group commands Control gear can be confgured n groups, f t has already been assgned to groups. Sendng commands to a group Requrement: Devces have been grouped. 1. In the DALI devce tree dagram, select the group to be confgured. The detal vew appears. 37

38 2. Clck on Send commands to... The Send commands to pop-up wndow appears. 3. Select the desred command from the drop-down menu. 4. Set the value usng the slder. Above the slder, the set value s dsplayed on the left n the relevant unt of measurement and on the rght as a DALI value (decmal). 5. Clck on Send command. The command s sent to the control gear n the selected group. 6. Optonally, test the confguraton. Informaton on how to check the confguraton appears n the pop-up wndow n the help text above the Test confguraton feld. A detaled descrpton of the confguraton and control commands can be found n Secton Confguraton commands for DALI control gear

39 8.1.1 Devce Type 0: Control gear for fluorescent lamps Control gear for fluorescent lamps are shown n the DALI devce tree dagram wth the short descrpton fluorescent. symbol and the Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 9: Devce nformaton Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. 39

40 Scenes The ntensty of the lumnare can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Enter a value between 0% and 100%. 3. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. For control gear for fluorescent lamps from seres xtec II, automatc means that the control gear enables automatc control when ths scene s recalled. More nformaton on automatc control can be found n Sectons Lght sensor and Moton sensor DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. 40

41 The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ brghtenng. Value range: Mnmum Level 100% Power On Level The selected value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Table 10: DALI default parameters 41

42 To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 42

43 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. 43

44 Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 11: DALI control gear status nformaton 44

45 Trdonc-specfc confguraton All Trdonc-specfc functons and status nformaton can be found n the Trdonc-specfc confguraton pop-up wndow. Not every control gear element supports all functons. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Open the Trdonc-specfc confguraton pop-up wndow 1. In the DALI devce tree dagram, rght-clck on the DALI control gear to be confgured. The context menu appears. 2. Select Trdonc-specfc confguraton n the context menu. The Trdonc-specfc confguraton pop-up wndow opens. -ordouble-clck the DALI control gear to be confgured n the DALI devce tree dagram. The Trdonc-specfc confguraton pop-up wndow opens. 45

46 Devce operatng mode The devce operatng mode used by the control gear n order to carry out ts functons can be set here. Devce operatng mode Descrpton Automatc detecton The control gear detects the ncomng sgnal and swtches automatcally to the correspondng devce operatng mode. The followng devce operatng modes are automatcally detected: DALI only DSI only swtchdim only DALI and SMART DSI and SMART swtchdim and SMART corrdorfunction DALI only The control gear detects only DALI commands. DSI only The control gear detects only DSI commands. swtchdim only The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches. The mans voltage s used as a control sgnal. The control gear nterprets the sgnal as ether a smooth adjustment or swtch command dependng on how long the manual momentary-acton swtch s pressed. SMART only The lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DALI and SMART The control gear detects only DALI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DSI and SMART The control gear detects only DSI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. swtchdim and SMART The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches or va the SMART nterface. corrdorfunction Functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects movement, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). There are four types of corrdorfunction: 46

47 corrdorfunction wth fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wth fade-n tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 4) Swtch-off delay corrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 4) Swtch-off delay Table 12: Devce operatng modes The DALI and SMART, DSI and SMART and swtchdim and SMART devce operatng modes are not supported by the control gear for fluorescent lamps belongng to the xtec II seres. 47

48 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Value range: 0 100% Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Value range: 0 100% Fade-n tme Tme requred to reach the presence value. Value range: fast s Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. The run-on tme can be confgured on the moton sensor. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Table 13: Overvew of corrdorfunction parameters 48

49 Commssonng date The commssonng date can be saved once n the control gear. Settng the commssonng date 1. The current day s marked n blue on the calendar. 2. Clck on save. Changes are stored n the devce. The date can only be set once. If the date has already been set, the commssonng date wll be dsplayed. 49

50 Compatblty settngs The generaton wth whch the control gear s compatble can be set here. Dependng on the compatblty settngs supported by the control gear, the followng optons are avalable: current generaton (n): the control gear uses the settngs for the current generaton. precedng generaton (n-1): the control gear uses the settngs for the precedng generaton (n-1). pre-precedng generaton (n-2): the control gear uses the settngs for the generaton before last (n-2). A detaled descrpton of whch parameters are changed (e.g. Mnmum level, Fade tme), can be found n the product documentaton for the correspondng control gear. Selectng compatblty settngs 1. Select the compatblty settng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. 50

51 Features The behavour n DC mode, epower On Level and preheatng tme can be set for the ndvdual control gear element n the Features tab. Behavour durng DC operaton The control gear can be set to recall a fxed control value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. can be smoothly adjusted or swtched on/off) here. Settng behavour durng DC operaton 1. Enter the release code. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Normal operaton. 3. Clck on save. Changes are stored n the devce.. The release code can be obtaned from your sales partner. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. epower On Level Here users can set whether the Power On Level (value after power has been restored) s overwrtten by an ed command. The epower On Level can be set to swtch the control gear to a fxed control value (0 100 %) or recall the memory value after power has been restored followng a falure. The memory value s the last control value to whch the control gear was set before the power falure. 51

52 Settng epower On Level 1. Enable the Enable epower On Level checkbox. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Memory value. 3. Clck on save. Changes are stored n the devce. Preheatng tme The control gear can be set to gnore the preheatng tme and mmedately swtch on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme checkbox. 2. Clck on save. Changes are stored n the devce. 52

53 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Status Descrpton Normal operaton durng DC operaton Indcates whether the control gear contnues n normal operaton durng DC operaton,.e. can be smoothly adjusted and swtched on/off. Compatblty Indcates the compatblty settng used by the control gear. Intellgent Temperature Guard (ITG) Indcates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght control Indcates whether the ambent lght control s enabled or dsabled. Supply voltage Indcates the supply voltage wth whch the control gear s operatng. Overvoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an overvoltage. When overvoltage s detected, the lamps connected to the control gear flash n alternatng successon. 53

54 Undervoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an undervoltage. When voltage under 70 V s detected, the lamps connected to the control gear swtch off. When voltage between 70 and 140 V s detected, the lamps connected to the control gear swtch on and off at rregular ntervals. SMART sensor connected Indcates whether a SMART sensor s connected and that no error has occurred. Yes: SMART sensor connected and no error No: no SMART sensor connected, or SMART sensor connected but error has occurred Slave mode actve Indcates whether the slave mode s enabled. In slave mode the sensor s connected to two devces smultaneously and cannot be confgured. The sensor only responds to commands from the master devce. LED temperature montorng (ITM) actve Indcates whether the LED temperature montorng (ITM) functon s enabled. ITM fault Indcates whether a short crcut has occurred for the temperature sensor used for LED temperature montorng (ITM). Table 14: Status nformaton 54

55 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. 55

56 Specal features: xtec II Varous SMART sensors and SMART plugs can be connected to control gear for fluorescent lamps from seres xtec II va a SMART nterface. More nformaton on possble combnatons of ndvdual xtec II control gear elements and SMART sensors/plugs can be found n the devce documentaton. Dfferent tabs (and thus dfferent combnaton optons) are dsplayed n the masterconfigurator dependng on whch SMART sensor/plug s connected. The tabs shown for specfc sensors or plugs are gven n the followng table: Devce name Lght sensor Moton sensor Remote control Plug SMART Sensor 5D x SMART Sensor 5DP x x SMART Sensor 5DPI x x x SMART Sensor 5DPI cf NO x x x x SMART Sensor 5DPI cf 01 x x x x SMART Sensor 5DPI cf 30 x x x x SMART Sensor 10DPI x x x SMART Sensor 10DPI cf NO x x x x SMART Sensor 10DPI cf 01 x x x x SMART Sensor 10DPI cf 30 x x x x SMART Plug MA x SMART Plug cf NO x SMART Plug cf 01 x SMART Plug cf 30 x SMART Plug GrA x SMART Plug GrB x SMART Plug GrC x SMART Plug GrD x Table 15: Overvew of SMART sensors and SMART plugs For further detals on ndvdual SMART sensors and SMART plugs, please refer to the relevant devce documentaton. 56

57 Lght sensor SMART devce nformaton The followng devce nformaton s dsplayed: Devce nformaton Descrpton Name Dsplays the name of the SMART sensor. Artcle number Dsplays the artcle number of the SMART sensor. Hardware verson Dsplays the hardware verson of the SMART sensor. Software verson Dsplays the software verson of the SMART sensor. Table 16: SMART devce nformaton Status The followng status nformaton s dsplayed for the lght sensor: Status Descrpton Illumnance Illumnance currently measured at the lght sensor. On account of the room condtons and the nstallaton heght, the llumnance n the workspace may, however, be three to four tmes hgher. Update status automatcally Indcates whether the lght sensor status s updated automatcally. Ambent lght control Indcates the status of ambent lght control for the lght sensor. enabled: ambent lght control s enabled. dsabled: ambent lght control s dsabled. started: ambent lght control has been started. The lght 57

58 sensor regulates the control gear to match the desred value. Table 17: Status nformaton Confguraton optons The followng confguraton optons are dsplayed for the lght sensor: Confguraton opton Descrpton Ambent lght control Ambent lght control can be enabled or dsabled. Automatc control Indcates the scene wth whch the ambent lght control s enabled. When ths scene s recalled, the sensor s enabled, the lumnares are swtched on and ambent lght control regulates the lumnares. : The scene selected here s dentfed n the Basc confguraton as automatc. Enable dmmng off (brght out) Checkbox enabled: f the measured llumnance exceeds the desred value by 150% for longer than 8.5 mnutes, the lumnare group wll be swtched off by the lght sensor even f movement s detected n the room. As soon as the measured llumnance falls below the desred value, the lumnare group s swtched on agan. Set desred value Set the desred value for ambent lght control. The desred value s the value to whch the lght sensor regulates the control gear. The default settng s 500 lx. Ths value can be smoothly adjusted usng the Dm and Brghten commands untl the desred llumnance s acheved. Use a luxmeter to acheve an accurate measurement of the llumnance. Table 18: Lght sensor confguraton optons 58

59 Automatc control for dfferent SMART sensors and SMART plugs The automatc control for the SMART Sensor 5D refers only to ambent lght control. In contrast, the automatc control for sensors SMART Sensor 5DP, SMART Sensor 5DPI and SMART Sensor 10DPI refers to a type of ambent lght control that depends on the presence of people. More nformaton can be found n Secton Moton sensor To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. Moton sensor SMART devce nformaton The followng devce nformaton s dsplayed: Devce nformaton Descrpton Name Dsplays the name of the SMART sensor. Artcle number Dsplays the artcle number of the SMART sensor. 59

60 Hardware verson Dsplays the hardware verson of the SMART sensor. Software verson Dsplays the software verson of the SMART sensor. Table 19: SMART devce nformaton Status The followng status nformaton s dsplayed for the moton sensor: Status Descrpton Update status automatcally Indcates whether the moton sensor status s updated automatcally. Moton sensor Indcates the status of the moton sensor: Movement detected No movement detected Table 20: Status nformaton Confguraton optons The followng confguraton optons are dsplayed for the moton sensor: Confguraton opton Descrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatcally swtched on and off dependng on whether presence s detected. (factory settng) enabled (only OFF): the moton sensor swtches the lghtng off only. It must be swtched on manually. dsabled: the moton sensor s dsabled. The lghtng must be swtched on and off manually. : The never OFF functon s mplemented as follows: 1. Select the enabled operatng mode. 2. Select swtch-off delay never OFF. Automatc control Indcates the scene used to control the lghtng based on whether presence s detected. If ths scene s recalled the moton sensor s enabled and the lumnares are controlled based on whether presence s detected. : The scene selected here s dentfed n the Basc confguraton as automatc. Table 21: Moton sensor confguraton optons 60

61 Automatc control for dfferent SMART sensors and SMART plugs The automatc control for sensors SMART Sensor 5DP, SMART Sensor 5DPI and SMART Sensor 10DPI refers to a type of ambent lght control that depends on the presence of people. Ambent lght control can be dsabled as follows: 1. Clck on the SMART lght sensor tab. 2. Select dsabled for ambent lght control. 3. Clck on save. Changes are stored n the devce. The moton sensor controls the lghtng based on the presence of people. corrdorfunction profles The corrdorfunction s a functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects presence, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). If the Operatng mode for the moton sensor s enabled, the user has fve profles from whch to choose. Profle Descrpton never off The corrdorfunction parameters cannot be confgured, wth the excepton of the dead tme. The followng values are saved n the profle: A) Presence value: 100% B) Absence value: 10% 1) Fade-n tme: < 0.7 s 2) Run-on tme: 20 mn 3) Fade tme: 32 s 4) Swtch-off delay: No swtch-off delay s defned for ths profle. Once the fade tme has expred, the absence value of 10% s mantaned untl the moton sensor once agan detects presence. Dead tme Swtch-off delay: 1 mn The corrdorfunction parameters cannot be confgured, wth the excepton of the dead tme. The followng values are saved n the profle: A) Presence value: 100% B) Absence value: 10% 1) Fade-n tme: < 0.7 s 2) Run-on tme: 20 mn 3) Fade tme: 32 s 4) Swtch-off delay: 1 mn Dead tme Swtch-off delay: 30 mn The corrdorfunction parameters cannot be confgured, wth the excepton of the dead tme. The followng values are saved n the profle: A) Presence value: 100% B) Absence value: 10% 1) Fade-n tme: < 0.7 s 2) Run-on tme: 20 mn 61

62 3) Fade tme: 32 s 4) Swtch-off delay: 30 mn Dead tme user-defned 1 The corrdorfunction parameters can be freely confgured, wth the excepton of the fade-n tme. A) Presence value B) Absence value 1) Fade-n tme: < 0.7 s (not confgurable) 2) Run-on tme 3) Fade tme 4) Swtch-off delay Dead tme user-defned 2 The corrdorfunction parameters can be freely confgured, wth the excepton of the fade-n tme. A) Presence value B) Absence value 1) Fade-n tme: < 0.7 s (not confgurable) 2) Run-on tme 3) Fade tme 4) Swtch-off delay Dead tme Table 22: corrdorfunction confguraton optons Overvew of confguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay A) Presence value B) Absence value 62

63 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Fade-n tme Tme requred to reach the presence value. Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Dead tme Tme started by manually swtchng off the lghtng va the momentary-acton swtch or the remote control and durng whch the moton sensor s dsabled. If movement s detected n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s detected n the room, the moton sensor s enabled agan. Table 23: Overvew of corrdorfunction parameters Remote control 63

64 SMART devce nformaton The followng devce nformaton s dsplayed: Devce nformaton Descrpton Name Dsplays the name of the SMART sensor. Artcle number Dsplays the artcle number of the SMART sensor. Hardware verson Dsplays the hardware verson of the SMART sensor. Software verson Dsplays the software verson of the SMART sensor. Table 24: SMART devce nformaton Confguraton optons The followng confguraton optons are dsplayed for the remote control: Confguraton opton Descrpton Remote control Remote control can be enabled or dsabled. : Only the SMART remote control can be used wth control gear from seres xtec II. The key assgnment has already been parametersed. ON: the maxmum level s recalled mmedately wthout any fade tme. OFF: the lumnares are swtched off mmedately wthout any fade tme. UP: the ntensty s ncreased by the steps defned n the fade rate. DOWN: the ntensty s reduced by the steps defned n the fade rate. SET: the current ntensty s saved as the desred value for ambent lght control. AUTOMATIC: automatc control s enabled. Table 25: Remote control confguraton optons To apply the changed values, clck on save. 64

65 Plug SMART devce nformaton The followng devce nformaton s dsplayed: Devce nformaton Descrpton Name Dsplays the name of the SMART plug. Artcle number Dsplays the artcle number of the SMART plug. Hardware verson Dsplays the hardware verson of the SMART plug. Software verson Dsplays the software verson of the SMART plug. Table 26: SMART devce nformaton Confguraton optons The followng confguraton optons are dsplayed for the plug: Confguraton opton Descrpton Plug Plug can be enabled or dsabled. Table 27: Plug confguraton optons To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 65

66 Specal feature: group plugs Group plugs automatcally assgn the DALI control gear element, nto whch they are plugged, to a group. Plug Effectve range SMART Plug GrA Group 0 SMART Plug GrB Group 1 SMART Plug GrC Group 2 SMART Plug GrD Group 3 Table 28: Group plugs and ther correspondng effectve ranges A group plug that has been plugged n can be reconfgured ndvdually. It can be assgned to another group or to more than one group. If a reconfgured group plug s plugged nto another DALI control gear element, ths element takes on the confguraton of the group plug the next tme the power s reset. Changng the group to whch a group plug belongs Requrement: Group plug s plugged nto a DALI control gear element. 1. In the DALI devce tree dagram, clck on the devce nto whch the group plug has been plugged. 2. Hold down the left mouse button. 3. Drag the devce to the desred group. (Drag & Drop) The devce s removed from the group n whch t was prevously located and s added to the desred group. The group has now been changed on the group plug. Assgnng a group plug to more than one group Requrement: Group plug s plugged nto a DALI control gear element. 1. In the DALI devce tree dagram, clck on the devce nto whch the group plug has been plugged. 2. Hold down the left mouse button. 3. In addton, hold down the CTRL key. 4. Drag the devce to the desred group. The devce s coped. It s now n both groups. The group has been saved addtonally on the group plug. The group plug s now assgned to both groups. 66

67 Deletng a group from a group plug Requrement: Group plug s plugged nto a DALI control gear element. 1. Rght-clck on the devce nto whch the group plug has been plugged. The context menu appears. 2. Select Remove devce from group n the context menu. The devce s removed from the group and appears once agan n the DALI devce tree dagram wthout a group. The group has now been deleted on the group plug. 67

68 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 29: DALI control gear status nformaton 68

69 SMART sensor status Status Descrpton Sensor connected Indcates whether a sensor s connected. Sensor defcency Indcates whether the sensor s experencng a defcency. Ambent lght control Indcates the status of ambent lght control for the lght sensor. enabled: ambent lght control s enabled. dsabled: ambent lght control s dsabled. started: ambent lght control has been started. The lght sensor regulates the control gear to match the desred value. Moton sensor enabled Indcates whether the moton sensor s enabled. Movement detected Indcates whether the moton sensor has detected movement. Slave mode actve Indcates whether the slave mode s enabled. The sensor cannot be confgured n slave mode. The sensor only responds to commands from the master devce. Plug defcency Indcates whether there s a fault wth the plug or the wrong plug s connected. Ths status nformaton s only dsplayed when a SMART plug s plugged n. Table 30: Sensor status nformaton 69

70 8.1.2 Devce Type 1: Control gear for emergency lghtng Control gear for emergency lghtng are shown n the DALI devce tree dagram wth the short descrpton Emergency lghtng. con and the A dstncton s made between three types of swtchng modes n the case of emergency lghtng: Non-mantaned lght The emergency lghtng s swtched off n mans operaton, the emergency lghtng s swtched on n emergency mode (f there s a power falure or durng emergency lghtng testng). Mantaned lght The emergency lghtng s permanently swtched on durng mans operaton and n emergency mode (e.g. escape sgn lumnares). Swtched mantaned lght The emergency lghtng can be swtched on and off n mans operaton and n emergency mode. There are also emergency lumnares that can be dmmed. Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 31: Devce nformaton 70

71 Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Not all control gear for emergency lghtng supports all the functons that can be set n the masterconfigurator software (e.g. settng scenes). Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. Scenes The ntensty of the lumnare can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Enter a value between 0% and 100%. 3. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. 71

72 DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ 72

73 brghtenng. Value range: Mnmum Level 100% Power On Level The selected value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Table 32: DALI default parameters To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 73

74 Devce-specfc confguraton On the Emergency lghtng tab, you can make the followng settngs for devce-specfc confguratons: Identfy emergency lumnare For a detaled descrpton, see Secton Identfcaton 75. Set the tme for emergency mode after mans power s restored For a detaled descrpton, see Secton Emergency mode after mans power s restored Confgure test settngs For a detaled descrpton, see Secton Test settngs 77. Dsable emergency lumnare through addtonal operatng modes For a detaled descrpton, see Secton Dsablng emergency lumnares 82. Defne ntensty settngs n emergency mode For a detaled descrpton, see Secton Intensty settngs n emergency mode

75 Identfcaton Here you can drectly dsplay the address of the emergency lumnare va the status LED on the devce. For ths purpose, the address s converted nto a sx-dgt bnary number, whch s represented as a flashng pattern. The red LED stands for bnary number 0, the green LED for bnary number 1. The followng optons are avalable to users n order to convert a bnary number to a decmal number: EM PRO Ident.TOOL software: You can download ths software from Trdonc's homepage at: Servces Software. EM PRO addressng tool (Artcle number ) In the masterconfigurator software there are 3 ways n whch emergency lumnares can be dentfed. Functon Descrpton Identfy emergency lumnare button The address of an emergency lumnare that s hghlghted n the devce tree dagram s dsplayed once or n an endless loop Enabled n the detal vew by clckng the Identfy emergency lumnare button Locate con For a detaled descrpton of ths functon, see ths secton. The address of an emergency lumnare that s hghlghted n the devce tree dagram s dsplayed n an endless loop Is enabled by clckng the Locate Identfy con con For a detaled descrpton of ths functon, see Secton Checkng devce assgnment The addresses of all the emergency lumnares connected to the DALI control lne are dsplayed n an endless loop s enabled by clckng the Identfy con For a detaled descrpton of ths functon, see Secton Checkng devce assgnment Table 33: Summary of dentfyng emergency lumnares 75

76 Identfy emergency lumnare once Clck the Identfy emergency lumnare button. The emergency lumnare's status LED sends the address of the emergency lumnare once as a bnary flashng pattern. Identfy emergency lumnare agan 1. Enable the Repeat dentfcaton checkbox. 2. Clck the Identfy emergency lumnare button. The emergency lumnare's status LED sends the address of the emergency lumnare n an endless loop as a bnary flashng pattern. 3. To qut dentfcaton, dsable the Repeat dentfcaton checkbox. The current status of ths functon can be seen n the Status tab. Emergency mode after mans power s restored Here you can set how long emergency mode s mantaned after mans power s restored. Ths functon s used, for example, to compensate for voltage fluctuatons after a power outage or to brdge the restrke tmes of hgh-pressure dscharge lamps. The battery must be suffcently charged n order to mantan emergency mode after mans power s restored. Set the tme for emergency mode after mans power s restored 1. Select a value n the dropdown lst. 2. Clck on save. Changes are stored n the devce. 76

77 Test settngs Here you can vew the current confguraton of the functon and duraton tests, confgure the functon and duraton tests and defne a test wndow wthn whch the control gear s to perform a test. Functon test Durng a functon test, a power falure s smulated n order to test whether the emergency lumnare s functonng properly. Confguraton opton Descrpton Number of hours untl the next test starts Indcates n how many hours the next functon test wll be performed. Interval Indcates at what ntervals the functon test s performed. The nterval for the functon test s specfed n days. Confgure Button used to confgure functon test. Start Button used to start functon test manually. A manual functon test must be performed after nstallng and addressng the emergency lumnare. Stop The control gear usually performs a functon test mmedately. It s only delayed f the emergency lumnare s n emergency mode or f the battery s not suffcently charged. To see whether the functon test has been started, vew the Status Operatng mode Functon test n progress tab. To see whether the functon test has been delayed, vew the Status Emergency lghtng status Functon test on hold tab. Button used to termnate a functon test that s n progress prematurely. Table 34: Functon test confguraton optons 77

78 Confgure functon test 1. In the Functon test group feld, clck the Confgure button. The Confgure functon test pop-up wndow appears. 2. In the dropdown lst, select an Interval wthn whch the test s to be performed. 3. In the dropdown lst, select a Tme at whch the test s to be performed. 4. Choose a start date for the functon test n the calendar. The current day s marked n blue on the calendar. 5. Clck OK. Functon test has been confgured. Settngs are transferred to the detal vew. 6. Clck on save. Changes are stored n the devce. 78

79 Duraton test Durng a duraton test, a power falure s smulated n order to test whether the emergency lumnare s functonng properly and whether the battery acheves ts nomnal operatng duraton. Confguraton opton Descrpton Number of hours untl the next test starts Indcates n how many hours the next duraton test wll be performed. Interval Indcates at what ntervals the duraton test s performed. The nterval for the duraton test s specfed n weeks. Confgure Ths button s used to confgure the duraton test. Start Button used to start duraton test manually. A manual duraton test must be performed after nstallng and addressng the emergency lumnare. Stop The control gear usually performs a duraton test mmedately. It s only delayed f the emergency lumnare s n emergency mode or f the battery s not fully charged. To see whether the duraton test has been started, vew the Status Operatng mode Duraton test n progress tab. To see whether the functon test has been delayed, vew the Status Emergency lghtng status Functon test on hold tab. Button used to termnate a duraton test that s n progress prematurely. Table 35: Duraton test confguraton optons 79

80 Confgure duraton test 1. In the Duraton test group feld, clck the Confgure button. The Confgure duraton test pop-up wndow appears. 2. In the dropdown lst, select an Interval wthn whch the test s to be performed. 3. In the dropdown lst, select a Tme at whch the test s to be performed. 4. Choose a start date for the duraton test n the calendar. The current day s marked n blue on the calendar. 5. Clck OK. Duraton test has been confgured. Settngs are transferred to the detal vew. 6. Clck on save. Changes are stored n the devce. 80

81 Test wndow The test wndow defnes the maxmum tme that may elapse between the scheduled start tme and the tme the test s actually performed. The test wndow must be at least 24 hours because the batteres can take up to 24 hours to fully charge when they are frst charged. Dfferent requrements apply n order to start a functon test and a duraton test. Test Requrement Functon test The emergency lumnare must be operatng under mans operaton. The battery must be suffcently charged to perform the test. Duraton test The emergency lumnare must be operatng under mans operaton. The battery must be fully charged to perform the test. Table 36: Test requrements If these requrements are not met, the test s delayed wthn the lmts of the test wndow. On the Status tab, the status of the emergency lghtng Functon test on hold or Duraton test on hold s set to yes. Set the tme for the test wndow 1. In the Test settngs group feld n the Test wndow dropdown lst, select a value for the test wndow. 2. Clck on save. Changes are stored n the devce. If the test s not performed wthn the tme defned n the test wndow, on the Status tab, the Test wndow for functon test exceeded or Test wndow for duraton test exceeded status s set to yes. 81

82 Dsablng emergency lumnares! Warnng Suppresson of safety devce! These operatng modes suppress a safety devce. The emergency lumnares are not swtched on n an emergency and ths can lead to fataltes or serous physcal njures. Make sure that there s not an emergency and emergency mode s not requred. To nterrupt the voltage supply wthout the emergency lumnare beng swtched on, t s possble to use the operatng modes nhbt mode and rest mode. Inhbt mode Rest mode The emergency lumnare s powered by the mans supply. Inhbt mode lasts no longer than 15 mnutes. Rest mode s enabled nstead of emergency mode f the voltage supply s nterrupted durng these 15 mnutes. Ths prevents the emergency lumnare from beng swtched on n emergency mode. If there s no power outage durng these 15 mnutes, nhbt mode s termnated and mans operaton s restored. The emergency lumnare remans delberately swtched off whle the voltage supply s nterrupted. Ths functon s used to ensure that the battery s not dscharged n cases where the voltage supply s delberately nterrupted. Applcaton example: Mantenance of emergency lumnares Applcaton example: Plant holdays Table 37: The dfference betw een nhbt mode and rest mode Enable/termnate nhbt mode Requrement: Voltage supply to emergency lumnare s present. 1. Make sure that emergency mode s not requred. 2. Clck on Inhbt mode. The operatng mode s enabled. 3. Interrupt the voltage supply wthn 15 mnutes. The emergency lumnare remans swtched off. Rest mode s enabled. As soon as the emergency lumnare's voltage supply s restored, mans operaton s enabled. 4. To enable emergency mode wthout restorng the voltage supply, clck Termnate nhbt/rest mode. Emergency mode s enabled. Not all control gear for emergency lghtng supports the Termnate nhbt/rest mode 82

83 functon. You can see whether the control gear for emergency lghtng supports ths status by lookng on the Overvew of functons tab. If the control gear for emergency lghtng does not support ths functon, nhbt or rest mode can only be termnated by restorng the voltage supply. The current status of ths functon can be seen n the Status tab. Enable/termnate rest mode Requrements: Voltage supply to emergency lumnare s nterrupted wthout there beng an emergency. DALI voltage supply s present. 1. Make sure that emergency mode s not requred. 2. Clck on Rest mode. The operatng mode s enabled. The emergency lumnare s swtched off. As soon as the emergency lumnare's voltage supply s restored, mans operaton s enabled. 3. To enable emergency mode when the voltage supply s nterrupted, clck Termnate nhbt/rest mode. Emergency mode s enabled. Not all control gear for emergency lghtng supports the Termnate nhbt/rest mode functon. You can see whether the control gear for emergency lghtng supports ths status by lookng on the Overvew of functons tab. If the control gear for emergency lghtng does not support ths functon, nhbt or rest mode can only be termnated by restorng the voltage supply. Intensty settngs n emergency mode Here you can set the ntensty wth whch the lamp s llumnated n emergency mode. The adjustable ntensty s lmted by a lower lmt and an upper lmt. Settng ntensty n emergency mode 1. Enter a percentage value that les between the lower lmt and the upper lmt for the ntensty n emergency mode. 2. Clck on save. Changes are stored n the devce. 83

84 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. 84

85 Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 38: DALI control gear status nformaton Devce-specfc status: Operatng mode Status Descrpton Rest mode actve Indcates whether the emergency lumnare s n rest mode. In rest mode the emergency lumnare remans delberately swtched off whle the voltage supply s nterrupted. Mans operaton actve Indcates whether the emergency lumnare s n mans operaton. The DALI control gear s powered by the mans supply. Emergency mode actve Indcates whether the emergency lumnare s n emergency mode. The DALI control gear s powered by the battery. Emergency mode after mans return actve Indcates whether the emergency lumnare s n emergency mode after mans power s restored. Functon test n progress Indcates whether a functon test s n progress. Duraton test n progress Indcates whether a duraton test s n progress. Hardwred nhbt mode actve Indcates whether the emergency lumnare s n nhbt mode. Inhbt mode s enabled by a swtch. If there s a power falure when nhbt mode s actve, rest mode s enabled nstead of emergency operaton. Ths prevents the emergency lumnare beng swtched on. Swtched mantaned lght on Indcates that, n the case of swtched mantaned lght, the emergency lumnare s swtched on n mans mode. Table 39: DALI control gear for emergency lghtng Devce-specfc status: Operatng mode 85

86 Devce-specfc status: Emergency lghtng status Status Descrpton Inhbt mode actve Indcates whether the emergency lumnare s n nhbt mode. Inhbt mode was enabled by the DALI command Inhbt. Rest mode s enabled nstead of emergency mode f the voltage supply s nterrupted whle nhbt mode s actve. Ths prevents the emergency lumnare beng swtched on n emergency mode. Functon test completed Indcates whether the latest functon test was completed. Duraton test completed Ths status does not provde any nformaton as to whether errors were found durng the functon test. Faults are lsted n the Faults group secton. Indcates whether the latest duraton test was completed. Ths status does not provde any nformaton as to whether faults were found durng the duraton test. Faults are lsted n the Faults group secton. Battery fully charged Indcates whether the battery s fully charged. Functon test on hold Indcates whether a functon test s on hold. The functon test s delayed wthn the lmts of the test wndow. Possble causes: Emergency lumnare s n operaton mode Battery not suffcently charged Duraton test on hold Indcates whether a duraton test s on hold. The duraton test s delayed wthn the lmts of the test wndow. Possble causes: Emergency lumnare s n operaton mode Battery not fully charged Identfcaton actve Indcates whether the emergency lumnare s beng dentfed. Addressed wth Physcal Selecton method Indcates whether the emergency lumnare was addressed wth Physcal Selecton method. Table 40: DALI control gear for emergency lghtng Devce-specfc status: Emergency lghtng status 86

87 Devce-specfc status: Addtonal nformaton Status Descrpton Battery chargng state Indcates battery state of charge (%) Tme span duraton test Indcates hours of servce reached at tme of latest duraton test. Lamp burnng hours n emergency mode Indcates how long the lamp was n emergency mode. Lamp burnng hours n emergency mode are ndcated n 1-hour ncrements. Total lamp burnng hours Indcates how long the lamp has been n operaton n total (mans operaton and emergency mode). Total lamp burnng hours are ndcated n 4-hour ncrements. Rated duraton Indcates the tme for whch the battery delvers the requred energy n emergency mode (usually 1 hour or 3 hours). Reset lamp burnng hours Button used to reset Lamp burnng hours n emergency mode and Total lamp burnng hours. Table 41: DALI control gear for emergency lghtng Devce-specfc status: Addtonal nformaton Devce-specfc status: Faults Status Descrpton Crcut defectve Indcates whether a crcut on the prnted crcut board (PCB) of the devce s defectve. Nomnal operatng tme not acheved Indcates whether, durng a duraton test, the nomnal operatng tme was not acheved. Battery fault Indcates whether there s a battery fault (e.g. open crcut, nsuffcent battery capacty, battery ncorrectly connected). Lamp falure detected durng emergency mode Indcates whether a lamp falure was detected n emergency mode or durng an emergency lghtng test. Test wndow for functon test exceeded Indcates whether the test wndow for the functon test was exceeded. Test wndow for duraton test exceeded Indcates whether the test wndow for the duraton test was exceeded. Functon test faled Indcates whether the latest functon test faled. Duraton test faled Indcates whether the latest duraton test faled. Table 42: DALI control gear for emergency lghtng Devce-specfc status: Faults 87

88 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. Specal feature Physcal Selecton method: If the Physcal Selecton method s supported, t can be confgured under Commssonng 2. Address 17. The control gear s addressed specfcally n accordance wth the addressng plan usng the Physcal Selecton method. 88

89 8.1.3 Devce Type 2: Control gear for hgh-pressure dscharge lamps Control gear for hgh-pressure dscharge lamps are shown n the DALI devce tree dagram wth the symbol and the short descrpton HID. There are three ways to confgure DALI control gear: va the detal vew 90 va devce-specfc confguraton va trdonc-specfc confguraton Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 43: Devce nformaton 89

90 Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. Scenes The ntensty of the lumnare can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Enter a value between 0% and 100%. 3. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. 90

91 DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ 91

92 brghtenng. Value range: Mnmum Level 100% Power On Level The selected value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Table 44: DALI default parameters To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld Devce-specfc confguraton Here you can drectly dsplay the address of the hgh-pressure dscharge lamps va the status LED on the devce. For ths purpose, the address s converted nto a sx-dgt bnary number, whch s represented as a flashng pattern. The red LED stands for bnary number 0, the green LED for bnary number 1. The followng optons are avalable to users n order to convert a bnary number to a decmal number: EM PRO Ident.TOOL software: You can download ths software from Trdonc's homepage at: Servces Software. EM PRO addressng tool (Artcle number ) In the masterconfigurator software hgh-pressure dscharge lamps can be dentfed as follows. Functon Locate con Descrpton The address of a hgh-pressure dscharge lamps that s hghlghted n the devce tree dagram s dsplayed n an endless loop Is enabled by clckng the Locate con For a detaled descrpton of ths functon, see Secton Checkng devce assgnment

93 After shutdown hgh-pressure dscharge lamps requre some tme to cool down before they can be regnted. Ideally, perform dentfcaton process when lamps are cold! If lamps were prevously gnted: Make sure that they could cool suffcently! Table 45: Summary of dentfyng hgh-pressure dscharge lamps 93

94 Identfy hgh-pressure dscharge lamp once Clck the Identfy button. The hgh-pressure dscharge lamp's status LED sends the address of the hgh-pressure dscharge lamp once as a bnary flashng pattern. Identfy hgh-pressure dscharge lamp agan 1. Enable the Repeat dentfcaton checkbox. 2. Clck the Identfy button. The hgh-pressure dscharge lamp's status LED sends the address of the hgh-pressure dscharge lamp n an endless loop as a bnary flashng pattern. 3. To qut dentfcaton, dsable the Repeat dentfcaton checkbox. The current status of ths functon can be seen n the Status tab Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. 94

95 General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 46: DALI control gear status nformaton 95

96 Devce type-specfc Status: HID-Status Status Descrpton Run-up tme ready Indcates whether the run-up tme s ready. Arc power at requested value Indcates whether the requested value of arc power has been reached after gnton. Watng for gnton Indcates whether a lamp could not be gnted. Identfcaton actve Indcates whether dentfcaton s actve. Table 47: DALI control gear status nformaton Devce type-specfc Status: Falures Status Descrpton Mans voltage too low Indcates whether mans voltage s too low. Mans voltage too hgh Indcates whether mans voltage s too hgh. Converter thermal overload Indcates whether the converter has been thermally overloaded. Ignton tme out Indcates whether gnton has been tmed out, that s, the lamp could not be gnted. Lamp voltage out of specfcaton Indcates whether lamp voltage s out of specfcaton. Lamp cyclng falure Indcates whether a lamp cyclng falure occurred. "Lamp cyclng falure" means that the lamp s n a cycle of constantly gntng and gong off agan. Table 48: DALI control gear status nformaton Devce type-specfc Status: Stored Falures Status Descrpton Mans voltage too low Indcates whether mans voltage s too low. Mans voltage too hgh Indcates whether mans voltage s too hgh. Converter thermal overload Indcates whether the converter has been thermally overloaded. Ignton tme out Indcates whether gnton has been tmed out, that s, the lamp could not be gnted. Lamp voltage out of specfcaton Indcates whether lamp voltage s out of specfcaton. Lamp cyclng falure Indcates whether a lamp cyclng falure occurred. "Lamp cyclng falure" means that the lamp s n a cycle of constantly gntng and gong off agan. Table 49: DALI control gear status nformaton 96

97 Trdonc-specfc confguraton All Trdonc-specfc functons and status nformaton can be found n the Trdonc-specfc confguraton pop-up wndow. Not every control gear element supports all functons. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Open the Trdonc-specfc confguraton pop-up wndow 1. In the DALI devce tree dagram, rght-clck on the DALI control gear to be confgured. The context menu appears. 2. Select Trdonc-specfc confguraton n the context menu. The Trdonc-specfc confguraton pop-up wndow opens. -ordouble-clck the DALI control gear to be confgured n the DALI devce tree dagram. The Trdonc-specfc confguraton pop-up wndow opens. 97

98 Devce operatng mode The devce operatng mode used by the control gear n order to carry out ts functons can be set here. Devce operatng mode Descrpton Automatc detecton The control gear detects the ncomng sgnal and swtches automatcally to the correspondng devce operatng mode. The followng devce operatng modes are automatcally detected: DALI only DSI only swtchdim only DALI and SMART DSI and SMART swtchdim and SMART corrdorfunction DALI only The control gear detects only DALI commands. DSI only The control gear detects only DSI commands. swtchdim only The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches. The mans voltage s used as a control sgnal. The control gear nterprets the sgnal as ether a smooth adjustment or swtch command dependng on how long the manual momentary-acton swtch s pressed. SMART only The lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DALI and SMART The control gear detects only DALI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DSI and SMART The control gear detects only DSI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. swtchdim and SMART The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches or va the SMART nterface. corrdorfunction Functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects movement, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). There are four types of corrdorfunction: 98

99 corrdorfunction wth fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wth fade-n tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 4) Swtch-off delay corrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 4) Swtch-off delay Table 50: Devce operatng modes The DALI and SMART, DSI and SMART and swtchdim and SMART devce operatng modes are not supported by the control gear for fluorescent lamps belongng to the xtec II seres. 99

100 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Value range: 0 100% Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Value range: 0 100% Fade-n tme Tme requred to reach the presence value. Value range: fast s Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. The run-on tme can be confgured on the moton sensor. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Table 51: Overvew of corrdorfunction parameters 100

101 Commssonng date The commssonng date can be saved once n the control gear. Settng the commssonng date 1. The current day s marked n blue on the calendar. 2. Clck on save. Changes are stored n the devce. The date can only be set once. If the date has already been set, the commssonng date wll be dsplayed. 101

102 Compatblty settngs The generaton wth whch the control gear s compatble can be set here. Dependng on the compatblty settngs supported by the control gear, the followng optons are avalable: current generaton (n): the control gear uses the settngs for the current generaton. precedng generaton (n-1): the control gear uses the settngs for the precedng generaton (n-1). pre-precedng generaton (n-2): the control gear uses the settngs for the generaton before last (n-2). A detaled descrpton of whch parameters are changed (e.g. Mnmum level, Fade tme), can be found n the product documentaton for the correspondng control gear. Selectng compatblty settngs 1. Select the compatblty settng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. 102

103 Features The behavour n DC mode, epower On Level and preheatng tme can be set for the ndvdual control gear element n the Features tab. Behavour durng DC operaton The control gear can be set to recall a fxed control value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. can be smoothly adjusted or swtched on/off) here. Settng behavour durng DC operaton 1. Enter the release code. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Normal operaton. 3. Clck on save. Changes are stored n the devce.. The release code can be obtaned from your sales partner. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. epower On Level Here users can set whether the Power On Level (value after power has been restored) s overwrtten by an ed command. The epower On Level can be set to swtch the control gear to a fxed control value (0 100 %) or recall the memory value after power has been restored followng a falure. The memory value s the last control value to whch the control gear was set before the power falure. 103

104 Settng epower On Level 1. Enable the Enable epower On Level checkbox. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Memory value. 3. Clck on save. Changes are stored n the devce. Preheatng tme The control gear can be set to gnore the preheatng tme and mmedately swtch on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme checkbox. 2. Clck on save. Changes are stored n the devce. 104

105 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Status Descrpton Normal operaton durng DC operaton Indcates whether the control gear contnues n normal operaton durng DC operaton,.e. can be smoothly adjusted and swtched on/off. Compatblty Indcates the compatblty settng used by the control gear. Intellgent Temperature Guard (ITG) Indcates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght control Indcates whether the ambent lght control s enabled or dsabled. Supply voltage Indcates the supply voltage wth whch the control gear s operatng. Overvoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an overvoltage. When overvoltage s detected, the lamps connected to the control gear flash n alternatng successon. 105

106 Undervoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an undervoltage. When voltage under 70 V s detected, the lamps connected to the control gear swtch off. When voltage between 70 and 140 V s detected, the lamps connected to the control gear swtch on and off at rregular ntervals. SMART sensor connected Indcates whether a SMART sensor s connected and that no error has occurred. Yes: SMART sensor connected and no error No: no SMART sensor connected, or SMART sensor connected but error has occurred Slave mode actve Indcates whether the slave mode s enabled. In slave mode the sensor s connected to two devces smultaneously and cannot be confgured. The sensor only responds to commands from the master devce. LED temperature montorng (ITM) actve Indcates whether the LED temperature montorng (ITM) functon s enabled. ITM fault Indcates whether a short crcut has occurred for the temperature sensor used for LED temperature montorng (ITM). Table 52: Status nformaton 106

107 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. 107

108 LCAI outdoor specal features chronostep Here you can confgure the chronostep functon. The lumnare calculates a vrtual mdnght (VM) based on the lamp burnng hours of the last 3 days. On ths bass, tme wndows can be defned wthn whch the ntensty of the lumnare can be reduced n one or two steps. 108

109 Overvew of chronostep functon The followng fgure shows a summary of the ndvdual parameters. 1) Reducton tme (t2 VM) A) Intensty 1 2) Reducton tme (VM t3) B) Intensty 2 (only for profles 2 5) 3) Reducton tme (t1 VM) (only for profles 2 5) C) Intensty 3 4) Reducton tme (VM t4) (only for profles 2 5) t0 Swtch-on tme t5 Swtch-off tme VM vrtual mdnght The reducton tmes are descrbed here: Parameter Descrpton 1) Reducton tme (t2 VM) Tme wndow before vrtual mdnght, durng whch the lumnare assumes ntensty 3. 2) Reducton tme (VM t3) Tme wndow after vrtual mdnght, durng whch the lumnare assumes ntensty 3. 3) Reducton tme (t1 VM) Tme wndow before vrtual mdnght, durng whch the lumnare assumes ntensty 2. 4) Reducton tme (VM t4) Tme wndow after vrtual mdnght, durng whch the lumnare assumes ntensty 2. Table 53: Overvew of reducton tmes 109

110 chronostep profles You can choose between 6 profles. If the chronostep and corrdorfunction functons are enabled at the same tme, ths may cause problems. Therefore check the devce operatng mode (Devce operatng mode tab) and ensure that corrdorfunction s not selected. Profle 0 (dsabled) The chronostep functon s dsabled. The ntensty of the lumnare s not reduced. Profle 1 (default) The ntensty of the lumnare s reduced n one step. Parameter Value range 1) Reducton tme (t2 VM) 0 10 h MASK: MASK means that the t2 tme wll be gnored. 2) Reducton tme (VM t3) 0 10 h MASK: MASK means that the t3 tme wll be gnored. A) Intensty 1 100% (cannot be set) C) Intensty 3 50% (cannot be set) Table 54: Profle 1 parameter (default) 110

111 Profles 2 5 (user-defned) These 4 profles can be confgured ndvdually by each user. The ntensty of the lumnare s reduced n two steps. Parameter 1) Reducton tme (t2 VM) Value range 0 10 h MASK: MASK means that the t2 tme wll be gnored. 2) Reducton tme (VM t3) The value must be smaller than the reducton tme (t1 VM) h MASK: MASK means that the t3 tme wll be gnored. The value must be smaller than the reducton tme (VM t4). 3) Reducton tme (t1 VM) 0 10 h MASK: MASK means that the t1 tme wll be gnored. 4) Reducton tme (VM t4) 0 10 h MASK: MASK means that the t4 tme wll be gnored. A) Intensty 1 100% (cannot be set) B) Intensty 2 0%; 5 100% C) Intensty 3 Intensty 2 must be less than Intensty 1. 0%; 5 100% Intensty 3 must be less than Intensty 2. Table 55: Profle parameters 2 5 (user-defned) 111

112 8.1.4 Devce Type 3: Control gear for low-voltage halogen lamps Control gear for low-voltage halogen lamps are shown n the DALI devce tree dagram wth the and the short descrpton low-voltage halogen. symbol There are three ways to confgure DALI control gear: va the detal vew 113 va control gear confguraton 119 va trdonc-specfc confguraton 122 Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 56: Devce nformaton 112

113 Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. Scenes The ntensty of the lumnare can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Enter a value between 0% and 100%. 3. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. 113

114 DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. 114

115 The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ brghtenng. Value range: Mnmum Level 100% Power On Level The selected value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Table 57: DALI default parameters 115

116 To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 116

117 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. 117

118 Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 58: DALI control gear status nformaton 118

119 Control gear confguraton General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. 119

120 Address mssng Indcates whether the DALI control gear s unaddressed. Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 59: DALI control gear status nformaton Advanced Status Descrpton Short crcut Indcates whether a short crcut has occurred. Open crcut Indcates whether there s an open crcut. Load decrease Indcates whether a load decrease s present. Load ncrease Indcates whether a load ncrease s present. Overcurrent protecton Indcates whether the overcurrent protecton has been trggered. The overcurrent protecton s trggered when the level exceeds or falls below the value of the reference measurement. Thermal shut down Indcates whether the permssble temperature of the lowvoltage transformer has been exceeded. Thermal overload Not yet supported. Referencng fault Indcates whether the reference measurement has faled. Table 60: Advanced status dsplay of DALI control gear for low -voltage halogen lamps Reference measurement Here you can perform a reference measurement. Ths determnes the current lamp load usng nternal processes and measurements. Ths can only be done f the control gear supports ths functon. Performng a reference measurement Clck on Start reference measurement. Reference measurement s performed. Ths lasts approxmately 5 mnutes. If the reference measurement fals, the status Referencng error wll be set to Yes. 120

121 Settng parameters Requrement: Control gear confguraton pop-up wndow open. 1. Clck on the desred parameter. 2. Set the value usng the slder. The gear. con appears. Ths ndcates that the command has not yet been sent to the DALI control Above the slder, the set value s dsplayed on the left n the relevant unt of measurement and on the rght as a DALI value (decmal). 3. Clck on Send command. The change s mplemented n the DALI control gear. The con appears. Ths ndcates that the command has not yet been sent to the DALI control gear. If the command s nconsstent wth another parameter and therefore cannot be appled to the DALI control gear, the con contnues to be dsplayed. Repeat steps 2 and Optonally, test the confguraton. Informaton on how to check the confguraton appears n the pop-up wndow n the help text above the Test confguraton feld. A detaled descrpton of the confguraton and control commands can be found n Secton Confguraton commands for DALI control gear

122 Trdonc-specfc confguraton All Trdonc-specfc functons and status nformaton can be found n the Trdonc-specfc confguraton pop-up wndow. Not every control gear element supports all functons. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Open the Trdonc-specfc confguraton pop-up wndow 1. In the DALI devce tree dagram, rght-clck on the DALI control gear to be confgured. The context menu appears. 2. Select Trdonc-specfc confguraton n the context menu. The Trdonc-specfc confguraton pop-up wndow opens. -ordouble-clck the DALI control gear to be confgured n the DALI devce tree dagram. The Trdonc-specfc confguraton pop-up wndow opens. 122

123 Devce operatng mode The devce operatng mode used by the control gear n order to carry out ts functons can be set here. Devce operatng mode Descrpton Automatc detecton The control gear detects the ncomng sgnal and swtches automatcally to the correspondng devce operatng mode. The followng devce operatng modes are automatcally detected: DALI only DSI only swtchdim only DALI and SMART DSI and SMART swtchdim and SMART corrdorfunction DALI only The control gear detects only DALI commands. DSI only The control gear detects only DSI commands. swtchdim only The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches. The mans voltage s used as a control sgnal. The control gear nterprets the sgnal as ether a smooth adjustment or swtch command dependng on how long the manual momentary-acton swtch s pressed. SMART only The lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DALI and SMART The control gear detects only DALI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DSI and SMART The control gear detects only DSI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. swtchdim and SMART The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches or va the SMART nterface. corrdorfunction Functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects movement, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). There are four types of corrdorfunction: 123

124 corrdorfunction wth fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wth fade-n tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 4) Swtch-off delay corrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 4) Swtch-off delay Table 61: Devce operatng modes The DALI and SMART, DSI and SMART and swtchdim and SMART devce operatng modes are not supported by the control gear for fluorescent lamps belongng to the xtec II seres. 124

125 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Value range: 0 100% Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Value range: 0 100% Fade-n tme Tme requred to reach the presence value. Value range: fast s Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. The run-on tme can be confgured on the moton sensor. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Table 62: Overvew of corrdorfunction parameters 125

126 Commssonng date The commssonng date can be saved once n the control gear. Settng the commssonng date 1. The current day s marked n blue on the calendar. 2. Clck on save. Changes are stored n the devce. The date can only be set once. If the date has already been set, the commssonng date wll be dsplayed. 126

127 Compatblty settngs The generaton wth whch the control gear s compatble can be set here. Dependng on the compatblty settngs supported by the control gear, the followng optons are avalable: current generaton (n): the control gear uses the settngs for the current generaton. precedng generaton (n-1): the control gear uses the settngs for the precedng generaton (n-1). pre-precedng generaton (n-2): the control gear uses the settngs for the generaton before last (n-2). A detaled descrpton of whch parameters are changed (e.g. Mnmum level, Fade tme), can be found n the product documentaton for the correspondng control gear. Selectng compatblty settngs 1. Select the compatblty settng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. 127

128 Features The behavour n DC mode, epower On Level and preheatng tme can be set for the ndvdual control gear element n the Features tab. Behavour durng DC operaton The control gear can be set to recall a fxed control value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. can be smoothly adjusted or swtched on/off) here. Settng behavour durng DC operaton 1. Enter the release code. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Normal operaton. 3. Clck on save. Changes are stored n the devce.. The release code can be obtaned from your sales partner. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. epower On Level Here users can set whether the Power On Level (value after power has been restored) s overwrtten by an ed command. The epower On Level can be set to swtch the control gear to a fxed control value (0 100 %) or recall the memory value after power has been restored followng a falure. The memory value s the last control value to whch the control gear was set before the power falure. 128

129 Settng epower On Level 1. Enable the Enable epower On Level checkbox. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Memory value. 3. Clck on save. Changes are stored n the devce. Preheatng tme The control gear can be set to gnore the preheatng tme and mmedately swtch on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme checkbox. 2. Clck on save. Changes are stored n the devce. 129

130 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Status Descrpton Normal operaton durng DC operaton Indcates whether the control gear contnues n normal operaton durng DC operaton,.e. can be smoothly adjusted and swtched on/off. Compatblty Indcates the compatblty settng used by the control gear. Intellgent Temperature Guard (ITG) Indcates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght control Indcates whether the ambent lght control s enabled or dsabled. Supply voltage Indcates the supply voltage wth whch the control gear s operatng. Overvoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an overvoltage. When overvoltage s detected, the lamps connected to the control gear flash n alternatng successon. 130

131 Undervoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an undervoltage. When voltage under 70 V s detected, the lamps connected to the control gear swtch off. When voltage between 70 and 140 V s detected, the lamps connected to the control gear swtch on and off at rregular ntervals. SMART sensor connected Indcates whether a SMART sensor s connected and that no error has occurred. Yes: SMART sensor connected and no error No: no SMART sensor connected, or SMART sensor connected but error has occurred Slave mode actve Indcates whether the slave mode s enabled. In slave mode the sensor s connected to two devces smultaneously and cannot be confgured. The sensor only responds to commands from the master devce. LED temperature montorng (ITM) actve Indcates whether the LED temperature montorng (ITM) functon s enabled. ITM fault Indcates whether a short crcut has occurred for the temperature sensor used for LED temperature montorng (ITM). Table 63: Status nformaton 131

132 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. 132

133 8.1.5 Devce Type 4: Control gear for phase dmmers Control gear for phase dmmers are shown n the DALI devce tree dagram wth the short descrpton phase dmmer. symbol and the Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 64: Devce nformaton Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. 133

134 Scenes The ntensty of the lumnare can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Enter a value between 0% and 100%. 3. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. 134

135 The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ brghtenng. Value range: Mnmum Level 100% Power On Level The selected value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Table 65: DALI default parameters To apply the changed values, clck on save. The saved confguraton can now be tested 135

136 drectly n the feld. 136

137 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. 137

138 Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 66: DALI control gear status nformaton 138

139 Trdonc-specfc confguraton All Trdonc-specfc functons and status nformaton can be found n the Trdonc-specfc confguraton pop-up wndow. Not every control gear element supports all functons. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Open the Trdonc-specfc confguraton pop-up wndow 1. In the DALI devce tree dagram, rght-clck on the DALI control gear to be confgured. The context menu appears. 2. Select Trdonc-specfc confguraton n the context menu. The Trdonc-specfc confguraton pop-up wndow opens. -ordouble-clck the DALI control gear to be confgured n the DALI devce tree dagram. The Trdonc-specfc confguraton pop-up wndow opens. 139

140 Devce operatng mode The devce operatng mode used by the control gear n order to carry out ts functons can be set here. Devce operatng mode Descrpton Automatc detecton The control gear detects the ncomng sgnal and swtches automatcally to the correspondng devce operatng mode. The followng devce operatng modes are automatcally detected: DALI only DSI only swtchdim only DALI and SMART DSI and SMART swtchdim and SMART corrdorfunction DALI only The control gear detects only DALI commands. DSI only The control gear detects only DSI commands. swtchdim only The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches. The mans voltage s used as a control sgnal. The control gear nterprets the sgnal as ether a smooth adjustment or swtch command dependng on how long the manual momentary-acton swtch s pressed. SMART only The lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DALI and SMART The control gear detects only DALI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DSI and SMART The control gear detects only DSI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. swtchdim and SMART The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches or va the SMART nterface. corrdorfunction Functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects movement, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). There are four types of corrdorfunction: 140

141 corrdorfunction wth fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wth fade-n tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 4) Swtch-off delay corrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 4) Swtch-off delay Table 67: Devce operatng modes The DALI and SMART, DSI and SMART and swtchdim and SMART devce operatng modes are not supported by the control gear for fluorescent lamps belongng to the xtec II seres. 141

142 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Value range: 0 100% Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Value range: 0 100% Fade-n tme Tme requred to reach the presence value. Value range: fast s Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. The run-on tme can be confgured on the moton sensor. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Table 68: Overvew of corrdorfunction parameters 142

143 Commssonng date The commssonng date can be saved once n the control gear. Settng the commssonng date 1. The current day s marked n blue on the calendar. 2. Clck on save. Changes are stored n the devce. The date can only be set once. If the date has already been set, the commssonng date wll be dsplayed. 143

144 Compatblty settngs The generaton wth whch the control gear s compatble can be set here. Dependng on the compatblty settngs supported by the control gear, the followng optons are avalable: current generaton (n): the control gear uses the settngs for the current generaton. precedng generaton (n-1): the control gear uses the settngs for the precedng generaton (n-1). pre-precedng generaton (n-2): the control gear uses the settngs for the generaton before last (n-2). A detaled descrpton of whch parameters are changed (e.g. Mnmum level, Fade tme), can be found n the product documentaton for the correspondng control gear. Selectng compatblty settngs 1. Select the compatblty settng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. 144

145 Features The behavour n DC mode, epower On Level and preheatng tme can be set for the ndvdual control gear element n the Features tab. Behavour durng DC operaton The control gear can be set to recall a fxed control value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. can be smoothly adjusted or swtched on/off) here. Settng behavour durng DC operaton 1. Enter the release code. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Normal operaton. 3. Clck on save. Changes are stored n the devce.. The release code can be obtaned from your sales partner. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. epower On Level Here users can set whether the Power On Level (value after power has been restored) s overwrtten by an ed command. The epower On Level can be set to swtch the control gear to a fxed control value (0 100 %) or recall the memory value after power has been restored followng a falure. The memory value s the last control value to whch the control gear was set before the power falure. 145

146 Settng epower On Level 1. Enable the Enable epower On Level checkbox. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Memory value. 3. Clck on save. Changes are stored n the devce. Preheatng tme The control gear can be set to gnore the preheatng tme and mmedately swtch on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme checkbox. 2. Clck on save. Changes are stored n the devce. 146

147 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Status Descrpton Normal operaton durng DC operaton Indcates whether the control gear contnues n normal operaton durng DC operaton,.e. can be smoothly adjusted and swtched on/off. Compatblty Indcates the compatblty settng used by the control gear. Intellgent Temperature Guard (ITG) Indcates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght control Indcates whether the ambent lght control s enabled or dsabled. Supply voltage Indcates the supply voltage wth whch the control gear s operatng. Overvoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an overvoltage. When overvoltage s detected, the lamps connected to the control gear flash n alternatng successon. 147

148 Undervoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an undervoltage. When voltage under 70 V s detected, the lamps connected to the control gear swtch off. When voltage between 70 and 140 V s detected, the lamps connected to the control gear swtch on and off at rregular ntervals. SMART sensor connected Indcates whether a SMART sensor s connected and that no error has occurred. Yes: SMART sensor connected and no error No: no SMART sensor connected, or SMART sensor connected but error has occurred Slave mode actve Indcates whether the slave mode s enabled. In slave mode the sensor s connected to two devces smultaneously and cannot be confgured. The sensor only responds to commands from the master devce. LED temperature montorng (ITM) actve Indcates whether the LED temperature montorng (ITM) functon s enabled. ITM fault Indcates whether a short crcut has occurred for the temperature sensor used for LED temperature montorng (ITM). Table 69: Status nformaton 148

149 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. 149

150 8.1.6 Devce Type 6: Control gear for LEDs Control gear for LEDs are shown n the DALI devce tree dagram wth the descrpton LED. symbol and the short Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 70: Devce nformaton Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. 150

151 Scenes The ntensty of the lumnare can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Enter a value between 0% and 100%. 3. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. 151

152 DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. 152

153 Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ brghtenng. Value range: Mnmum Level 100% Power On Level The selected value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Table 71: DALI default parameters To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 153

154 Devce-specfc confguraton The dmmng curve can be selected, fast fade tme can be enabled and a reference measurement can be carred out n the LED tab. Dmmng curve The course of the lumnous flux of the lumnare durng smooth adjustment can be set here. lnear: the lumnous flux s changed lnearly durng smooth adjustment. Ths does not match the senstvty of the human eye and mght not be perceved as smooth. logarthmc: the lumnous flux of the lumnare s changed logarthmcally durng smooth adjustment as per the DALI specfcaton. Ths matches the senstvty of the human eye and s therefore perceved as smooth. Settng the dmmng curve 1. Clck lnear or logarthmc. 2. Clck on save. Changes are stored n the devce. The detal vew shows n the Status tab whether a lnear dmmng curve has been selected. Fast Fade Tme The Fast Fade Tme can be selected nstead of the fade tme here. The fade tme s gven n seconds. Ths settng can be defned n the Basc confguraton tab. The Fast Fade Tme s gven n mllseconds (< 25 ms 675 ms). Settng the Fast Fade Tme Requrement: In the Basc confguraton tab, set the Fade tme to Set the value usng the slder. 2. Clck on save. Changes are stored n the devce. 154

155 Reference measurement Here you can perform a reference measurement. Ths determnes the current lamp load usng nternal processes and measurements. Ths can only be done f the control gear supports ths functon. Performng a reference measurement Clck on Start. Reference measurement s performed. Ths lasts approxmately 5 mnutes. If the reference measurement fals, the status Referencng error wll be set to Yes. 155

156 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. 156

157 Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 72: DALI control gear status nformaton Status of control gear for LEDs (DT6) Status Descrpton Short crcut Indcates whether a short crcut has occurred. Open crcut Indcates whether there s an open crcut. Load decrease Indcates whether a load decrease s present. Load ncrease Indcates whether a load ncrease s present. Overcurrent protecton Indcates whether the overcurrent protecton has been trggered. The overcurrent protecton s trggered when the level exceeds or falls below the value of the reference measurement. Thermal shut down Indcates whether the permssble temperature of the control gear for LEDs has been exceeded. Thermal overload Not yet supported. Referencng fault Indcates whether the reference measurement has faled. Pulse wdth modulaton Indcates whether the lamps connected to the control gear are operated wth pulse wdth modulaton. Ampltude modulaton Indcates whether the lamps connected to the control gear are operated wth ampltude modulaton. Current control mode Indcates whether the lamps connected to the control gear are operated wth current control. Hgh-current pulse Indcates whether the lamps connected to the control gear are operated wth hgh-current pulse. Lnear dmmng curves Indcates whether a non-logarthmc dmmng curve (e.g. lnear dmmng curve) s enabled. Table 73: Devce-specfc status nformaton for DALI control gear for LEDs 157

158 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. Specal feature Physcal Selecton method: If the Physcal Selecton method s supported, t can be confgured under Commssonng 2. Address 17. The control gear s addressed specfcally n accordance wth the addressng plan usng the Physcal Selecton method. 158

159 Trdonc-specfc confguraton All Trdonc-specfc functons and status nformaton can be found n the Trdonc-specfc confguraton pop-up wndow. Not every control gear element supports all functons. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Open the Trdonc-specfc confguraton pop-up wndow 1. In the DALI devce tree dagram, rght-clck on the DALI control gear to be confgured. The context menu appears. 2. Select Trdonc-specfc confguraton n the context menu. The Trdonc-specfc confguraton pop-up wndow opens. -ordouble-clck the DALI control gear to be confgured n the DALI devce tree dagram. The Trdonc-specfc confguraton pop-up wndow opens. 159

160 Devce operatng mode The devce operatng mode used by the control gear n order to carry out ts functons can be set here. Devce operatng mode Descrpton Automatc detecton The control gear detects the ncomng sgnal and swtches automatcally to the correspondng devce operatng mode. The followng devce operatng modes are automatcally detected: DALI only DSI only swtchdim only DALI and SMART DSI and SMART swtchdim and SMART corrdorfunction DALI only The control gear detects only DALI commands. DSI only The control gear detects only DSI commands. swtchdim only The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches. The mans voltage s used as a control sgnal. The control gear nterprets the sgnal as ether a smooth adjustment or swtch command dependng on how long the manual momentary-acton swtch s pressed. SMART only The lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DALI and SMART The control gear detects only DALI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DSI and SMART The control gear detects only DSI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. swtchdim and SMART The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches or va the SMART nterface. corrdorfunction Functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects movement, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). There are four types of corrdorfunction: 160

161 corrdorfunction wth fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wth fade-n tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 4) Swtch-off delay corrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 4) Swtch-off delay Table 74: Devce operatng modes The DALI and SMART, DSI and SMART and swtchdim and SMART devce operatng modes are not supported by the control gear for fluorescent lamps belongng to the xtec II seres. 161

162 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Value range: 0 100% Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Value range: 0 100% Fade-n tme Tme requred to reach the presence value. Value range: fast s Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. The run-on tme can be confgured on the moton sensor. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Table 75: Overvew of corrdorfunction parameters 162

163 Commssonng date The commssonng date can be saved once n the control gear. Settng the commssonng date 1. The current day s marked n blue on the calendar. 2. Clck on save. Changes are stored n the devce. The date can only be set once. If the date has already been set, the commssonng date wll be dsplayed. 163

164 Compatblty settngs The generaton wth whch the control gear s compatble can be set here. Dependng on the compatblty settngs supported by the control gear, the followng optons are avalable: current generaton (n): the control gear uses the settngs for the current generaton. precedng generaton (n-1): the control gear uses the settngs for the precedng generaton (n-1). pre-precedng generaton (n-2): the control gear uses the settngs for the generaton before last (n-2). A detaled descrpton of whch parameters are changed (e.g. Mnmum level, Fade tme), can be found n the product documentaton for the correspondng control gear. Selectng compatblty settngs 1. Select the compatblty settng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. 164

165 ITM LED temperature montorng can be confgured here. LED temperature montorng s ntended to protect the LED aganst thermal damage. Parameter Descrpton dsable temporarly LED temperature montorng s enabled as soon as a temperature sensor s connected. Ths functon can be temporarly dsabled usng the dsable temporarly button. As soon as the lghtng s swtched off and then on agan, the temperature sensor at the nput s detected once more and LED temperature montorng s re-enabled. To completely dsable LED temperature montorng, the temperature sensor must be removed. Further nformaton can be found on the data sheet for the ndvdual devce. Data sheets are avalable to downloaded onlne at Temperature sensor Indcates whether a temperature sensor s connected. Maxmum swtch-off temperature Indcates the maxmum confgurable swtch-off temperature. Mnmum swtch-off temperature Indcates the mnmum confgurable swtch-off temperature. Swtch-off temperature Indcates the temperature at whch the control gear for the LED s swtched off to protect the LED aganst thermal 165

166 damage. Ths allows the LED to cool. The control gear for the LED remans swtched off untl the temperature for restart s reached. Value range: mnmum swtch-off temperature maxmum swtchoff temperature Start power reducton at Indcates the temperature at whch the LED output current s gradually reduced. The LED s dmmed. Ths allows the LED to cool. The LED s gradually dmmed untl the temperature reduces by 10%, or 50% of the current ntensty has been reached. Value range: Ths temperature s calculated automatcally. The value s 15% below the swtch-off temperature. Stop power reducton at If the temperature contnues to ncrease despte the power reducton, the control gear for the LED s swtched off as soon as the swtch-off temperature s reached. Temperature at whch the reducton of the LED output current s stopped and the LED output current s gradually ncreased agan. LED output current s gradually ncreased untl the temperature reaches the start power reducton at parameter. Value range: Ths temperature s calculated automatcally. Value s 10% below the temperature at whch the power reducton starts. Temperature for restart Indcates the temperature at whch the LED output current s swtched back on after a thermal shut down: The LED output current assumes the value before the Intellgent Temperature Management was actvated. Value range: Ths temperature s calculated automatcally. The value s 50 % below the swtch-off temperature. Table 76: Parameters for LED temperature montorng 166

167 Features The behavour n DC mode, epower On Level and preheatng tme can be set for the ndvdual control gear element n the Features tab. Behavour durng DC operaton The control gear can be set to recall a fxed control value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. can be smoothly adjusted or swtched on/off) here. Settng behavour durng DC operaton 1. Enter the release code. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Normal operaton. 3. Clck on save. Changes are stored n the devce.. The release code can be obtaned from your sales partner. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. epower On Level Here users can set whether the Power On Level (value after power has been restored) s overwrtten by an ed command. The epower On Level can be set to swtch the control gear to a fxed control value (0 100 %) or recall the memory value after power has been restored followng a falure. The memory value s the last control value to whch the control gear was set before the power falure. 167

168 Settng epower On Level 1. Enable the Enable epower On Level checkbox. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Memory value. 3. Clck on save. Changes are stored n the devce. Preheatng tme The control gear can be set to gnore the preheatng tme and mmedately swtch on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme checkbox. 2. Clck on save. Changes are stored n the devce. 168

169 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Status Descrpton Normal operaton durng DC operaton Indcates whether the control gear contnues n normal operaton durng DC operaton,.e. can be smoothly adjusted and swtched on/off. Compatblty Indcates the compatblty settng used by the control gear. Intellgent Temperature Guard (ITG) Indcates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght control Indcates whether the ambent lght control s enabled or dsabled. Supply voltage Indcates the supply voltage wth whch the control gear s operatng. Overvoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an overvoltage. When overvoltage s detected, the lamps connected to the control gear flash n alternatng successon. 169

170 Undervoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an undervoltage. When voltage under 70 V s detected, the lamps connected to the control gear swtch off. When voltage between 70 and 140 V s detected, the lamps connected to the control gear swtch on and off at rregular ntervals. SMART sensor connected Indcates whether a SMART sensor s connected and that no error has occurred. Yes: SMART sensor connected and no error No: no SMART sensor connected, or SMART sensor connected but error has occurred Slave mode actve Indcates whether the slave mode s enabled. In slave mode the sensor s connected to two devces smultaneously and cannot be confgured. The sensor only responds to commands from the master devce. LED temperature montorng (ITM) actve Indcates whether the LED temperature montorng (ITM) functon s enabled. ITM fault Indcates whether a short crcut has occurred for the temperature sensor used for LED temperature montorng (ITM). Table 77: Status nformaton 170

171 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. 171

172 LCAI outdoor specal features For control gear for LEDs that have been developed for outdoor lghts and streetlghts, addtonal confguraton optons are avalable n the Trdonc-specfc confguraton pop-up wndow. Optcal Balancng Here you can dvde the avalable output current between one or two outputs. The maxmum total current s 1 A. Dstrbutng output current to one output 1. Enable checkbox of one output. Slder becomes adjustable. 2. Use the slder to set a value between 170 and 700 ma. The value s shown to the left of the slder. 3. Clck on save. Changes are stored n the devce. 172

173 Dvdng output current between two outputs 1. Enable checkboxes of outputs 1 and 2. Slders become adjustable. 2. Use the slder to set a value between 170 and 700 ma for output 1. The value s shown to the left of the slder. 3. Use the slder to set a value between 170 and 700 ma for output 2. The value s shown to the left of the slder. The maxmum total current s 1 A. If the output current for one output s set such that the maxmum total current s exceeded, the value at the other output wll be automatcally reduced. 4. Clck on save. Changes are stored n the devce. Usng predefned values for the output current dstrbuton 1. Clck on the button for a predefned output current dstrbuton. The values are shown to the left of the slders. 2. Clck on save. Changes are stored n the devce. 173

174 chronostep Here you can confgure the chronostep functon. The lumnare calculates a vrtual mdnght (VM) based on the lamp burnng hours of the last 3 days. On ths bass, tme wndows can be defned wthn whch the ntensty of the lumnare can be reduced n one or two steps. 174

175 Overvew of chronostep functon The followng fgure shows a summary of the ndvdual parameters. 1) Reducton tme (t2 VM) A) Intensty 1 2) Reducton tme (VM t3) B) Intensty 2 (only for profles 2 5) 3) Reducton tme (t1 VM) (only for profles 2 5) C) Intensty 3 4) Reducton tme (VM t4) (only for profles 2 5) t0 Swtch-on tme t5 Swtch-off tme VM vrtual mdnght The reducton tmes are descrbed here: Parameter Descrpton 1) Reducton tme (t2 VM) Tme wndow before vrtual mdnght, durng whch the lumnare assumes ntensty 3. 2) Reducton tme (VM t3) Tme wndow after vrtual mdnght, durng whch the lumnare assumes ntensty 3. 3) Reducton tme (t1 VM) Tme wndow before vrtual mdnght, durng whch the lumnare assumes ntensty 2. 4) Reducton tme (VM t4) Tme wndow after vrtual mdnght, durng whch the lumnare assumes ntensty 2. Table 78: Overvew of reducton tmes 175

176 chronostep profles You can choose between 6 profles. If the chronostep and corrdorfunction functons are enabled at the same tme, ths may cause problems. Therefore check the devce operatng mode (Devce operatng mode tab) and ensure that corrdorfunction s not selected. Profle 0 (dsabled) The chronostep functon s dsabled. The ntensty of the lumnare s not reduced. Profle 1 (default) The ntensty of the lumnare s reduced n one step. Parameter Value range 1) Reducton tme (t2 VM) 0 10 h MASK: MASK means that the t2 tme wll be gnored. 2) Reducton tme (VM t3) 0 10 h MASK: MASK means that the t3 tme wll be gnored. A) Intensty 1 100% (cannot be set) C) Intensty 3 50% (cannot be set) Table 79: Profle 1 parameter (default) 176

177 Profles 2 5 (user-defned) These 4 profles can be confgured ndvdually by each user. The ntensty of the lumnare s reduced n two steps. Parameter 1) Reducton tme (t2 VM) Value range 0 10 h MASK: MASK means that the t2 tme wll be gnored. 2) Reducton tme (VM t3) The value must be smaller than the reducton tme (t1 VM) h MASK: MASK means that the t3 tme wll be gnored. The value must be smaller than the reducton tme (VM t4). 3) Reducton tme (t1 VM) 0 10 h MASK: MASK means that the t1 tme wll be gnored. 4) Reducton tme (VM t4) 0 10 h MASK: MASK means that the t4 tme wll be gnored. A) Intensty 1 100% (cannot be set) B) Intensty 2 0%; 5 100% C) Intensty 3 Intensty 2 must be less than Intensty 1. 0%; 5 100% Intensty 3 must be less than Intensty 2. Table 80: Profle parameters 2 5 (user-defned) 177

178 LED temperature montorng LED temperature montorng can be confgured here. LED temperature montorng s ntended to protect the LED aganst thermal damage. Parameter Descrpton Temperature montorng Temperature montorng can be enabled or dsabled. Temperature sensor Indcates whether a temperature sensor s connected. Temperature currently measured at the LED Indcates the temperature currently measured at the LED. Swtch-off temperature Indcates the temperature at whch the control gear for the LED s swtched off to protect the LED aganst thermal damage. Ths allows the LED to cool. The control gear for the LED remans swtched off untl the temperature for restart s reached. Value range: C 178

179 Start power reducton at Indcates the temperature at whch the LED output current s gradually reduced. The LED s dmmed. Ths allows the LED to cool. The LED s dmmed untl the temperature has fallen by 5 C. Value range: Ths temperature s calculated automatcally. It s 5 C below the swtch-off temperature. Stop power reducton at If the temperature contnues to ncrease despte the power reducton, the control gear for the LED s swtched off as soon as the swtch-off temperature s reached. Temperature at whch the reducton of the LED output current s stopped and the LED output current s gradually ncreased agan. LED output current s gradually ncreased untl the temperature reaches the start power reducton at parameter. Value range: Ths temperature s calculated automatcally. It s 5 C below the temperature at whch the power reducton s started. Temperature for restart Indcates the temperature at whch the LED output current s swtched back on after a thermal shut down: The LED output current assumes the value before the Intellgent Temperature Management was actvated. Value range: Ths temperature s calculated automatcally. It s 30 C below the swtch-off temperature. Table 81: LED temperature montorng parameters 179

180 LCAI ECO specal features Addtonal confguraton optons are avalable for LCAI ECO control gear for LEDs n the Trdonc-specfc confguraton pop-up wndow. I-Select The electrc current used by the control gear to supply the connected LEDs can be confgured here. Not every control gear element supports ths functon. Whether ths functon s supported by the control gear can be found on the data sheet for the ndvdual devce. Data sheets are avalable to downloaded onlne at Parameter Descrpton Output current Indcates the electrc current used by the control gear to supply the connected LEDs. Maxmum output current Indcates the maxmum confgurable electrc current that can be used by the control gear to supply the connected LEDs. Mnmum output current Indcates the mnmum confgurable electrc current that can be used by the control gear to supply the connected LEDs. Table 82: Parameters for adjustable output current 180

181 Confgurng the output current usng the masterconfigurator software 1. Enable the va software rado button. 2. Enter a value between the maxmum and mnmum output current n the nput feld. -orclck a button wth a predefned value. The value s dsplayed n the nput feld. 3. Clck on save. Changes are stored n the devce. The control gear only regulates to the saved output current once the voltage supply to the control gear s dsconnected and then reconnected agan. Confgurng the output current va the termnal on the control gear 1. Dsconnect the voltage supply to the control gear. 2. To set the mnmum output current, do not brdge the termnal on the control gear. -orto set the maxmum output current, brdge the termnal on the control gear. -orto set a value between the mnmum and maxmum output current, use a resstor. The types of resstors whch can be used can be found on the data sheet for the ndvdual devce. Data sheets are avalable to downloaded onlne at 3. Reconnect the voltage supply to the control gear. 4. Enable the va termnal rado button. 5. Clck on save. Changes are stored n the devce. The control gear only regulates to the saved output current once the voltage supply to the control gear s dsconnected and then reconnected agan. 181

182 CLO and OTL The CLO and OTL functons can be confgured here. CLO The CLO functon s a control to ensure that the requred ntensty remans constant over the entre LED lamp lfe. CLO dsabled Requred ntensty: 100% Expected LED lfe: 50,000 h The ntensty of an LED contnuously decreases over the LED lamp lfe. The control gear does not compensate for ths decrease. For ths reason the requred ntensty can no longer be ensured over the entrety of the LED's lamp lfe. CLO enabled Requred ntensty: 80% Expected LED lfe: 50,000 h A requred ntensty must be defned n order to ensure a constant ntensty over the LED lamp lfe. Ths ntensty s based on the natural reducton of ntensty defned by the LED manufacturer. The control gear compensated for ths natural reducton by adjustng ts own output accordngly. Table 83: Dfference betw een enabled and dsabled CLO functon OTL If the OTL functon s enabled, vsual feedback s gven as soon as the LED exceeds the expected LED lamp lfe. If the expected LED lamp lfe s exceeded, the lumnare flashes for 2 seconds after beng swtched on. 182

183 Parameter Descrpton Constant ntensty (CLO) The CLO functon can be enabled or dsabled. Vsual feedback (OTL) The OTL functon can be enabled or dsabled. Power of the control gear Indcates the current control gear output requred for reachng the requred ntensty. Requred ntensty Indcates the ntensty whch should reman constant over the entrety of the LED lamp lfe. Value range: % LED burnng hours Indcates the duraton for whch the LED has been on. If only the OTL functon s enabled, the Requred ntensty cannot be confgured. It wll be set at 100%. If the Advanced settngs are enabled, the LED burnng hours can be confgured. Informaton on how to enable the Advanced settngs can be found n Secton Actve wndow

184 Expected LED lfe Indcates the duraton for whch the LED can be operated before t becomes unusable or no longer meets the crtera gven n applcable standards. Value range: 0 127,500 h The Expected LED lfe s confgured n 500-hour ncrements. Table 84: Parameters for CLO and OTL functons If faulty control gear for LEDs must be replaced, we recommend applyng the settngs from another control gear element for LEDs to the new control gear element for LEDs. Applyng settngs from another control gear element for LEDs Requrements: Advanced settngs are enabled. Old control gear for LEDs has been replaced by new control gear for LEDs. 1. Dsplay the nformaton for a control gear element for LEDs located n the same room as the new control gear element for LEDs. 2. Open the Trdonc-specfc confguraton pop-up wndow. 3. Clck the CLO and OTL tab. 4. Make a note of the values for the followng parameters: Requred ntensty, LED burnng hours and Expected LED lfe. 5. Close the Trdonc-specfc confguraton pop-up wndow. 6. Dsplay the nformaton for the new control gear element for LEDs. 7. Open the Trdonc-specfc confguraton pop-up wndow. 8. Clck the CLO and OTL tab. 9. Enter the values prevously noted from the other control gear element for the followng parameters: Requred ntensty, LED burnng hours and Expected LED lfe. 10.Clck on save. Changes are stored n the devce. 184

185 Power-up Fadng The tme t takes after lghtng s swtched on for t to reach the value set for when power s restored (Power On Level or epower On Level) can be confgured here. The Power-up Fadng functon s only avalable when the lghtng s swtched on va the supply voltage or swtchdim. Value range: 0 16 s, where 0 s s the fastest tme and 16 s the longest. The Power-up Fadng functon does not affect the fade tme, as these are two dfferent functons. For a detaled descrpton of the fade tme, see Secton Devce type 6: control gear for LEDs > Basc confguraton 152. Confgurng Power-up Fadng for the Power On Level Requrement: epower On Level functon s dsabled. 1. Select the tme for Power-up Fadng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The value for the Power On Level can be changed n the Basc confguraton detal vew n the DALI default parameters group box. For a detaled descrpton of the Power On Level, see Secton Devce type 6: control gear for LEDs > Basc confguraton

186 Confgurng Power-up Fadng for the epower On Level Requrements: Control gear supports the epower On Level functon. epower On Level functon s enabled. 1. Select the tme for Power-up Fadng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The value for the epower On Level can be changed n the Trdonc-specfc confguraton pop-up wndow n the Features tab. For a detaled descrpton of the epower On Level, see Secton Features

187 8.1.7 Devce Type 8: Control gear for colour converters Control gear for colour converters are shown n the DALI devce tree dagram wth the short descrpton colour. symbol and the Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 85: Devce nformaton 187

188 Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. Settng scenes The ntensty of the lumnare and ts colour temperature or xy-coordnates can be set for all 16 scenes (0 15) here. The detal vew shows an overvew of the set scenes. The settngs can be defned n the Set scene pop-up wndow. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. Clck the button. The Set scene pop-up wndow appears. 3. Set the value for the ntensty usng the slder. -orclck MASK. 4. Select colour type colour temperature, xy-coordnates or MASK. The vew s updated. 5. Set the colour temperature or xy-coordnates. Adjustng the colour temperature Settng the xy-coordnates 188

189 Set the value usng the slder. -orclck the button for a pre-defned colour temperature, e.g K. Set the value usng the slders. -orclck the button for pre-defned xy-coordnates, e.g. Bakery products/gold. 189

190 6. Clck OK. The settngs are appled. The pop-up wndow s closed. 7. Clck on save. Changes are stored n the devce. 190

191 Settng DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. 2. Clck on save. Changes are stored n the devce. The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The selected value s set as the dmmng speed. It ndcates by how many steps per second the ntensty s changed. The Fade Rate s used wth the DALI commands Brghten (Up) and Dm (Down). Value range: steps per second : 45 steps per second s the DALI default. 358 steps per second s the fastest fade rate, and 2.8 steps per second s the slowest. Mnmum Level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum Level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ brghtenng. Value range: Mnmum Level 100% 191

192 Power On Level The selected value s set as the value after power s restored. There are two values for the Power On Level: one for ntensty and one for the colour temperature or xycoordnates. System Falure Level The selected value s set as the value n the event of falure of the DALI power supply. There are two values for the System Falure Level: one for ntensty and one for the colour temperature or xy-coordnates. Table 86: DALI default parameters 192

193 Specal feature: Settng the Power On Level and System Falure Level The Power On Level and the System Falure Level are set va a separate pop-up wndow. 1. Clck the button. The Set Power On Level or Set System Falure Level pop-up wndow appears. 2. Set the value for the ntensty usng the slder. -orclck MASK. 3. Select colour type colour temperature, xy-coordnates or MASK. The vew s updated. 4. Set the colour temperature or xy-coordnates. Adjustng the colour temperature Set the value usng the slder. -orclck the button for a pre-defned colour temperature, e.g K. Settng the xy-coordnates Set the value usng the slders. -orclck the button for pre-defned xy-coordnates, e.g. Bakery products/gold. 5. Clck OK. The settngs are appled. 6. Clck on save. Changes are stored n the devce. 193

194 Devce-specfc confguraton The colour temperature range can be set, automatc calbraton can be carred out and colours can be drectly changed n the Colour tab. Colour temperature range The range n whch the colour temperature of the lamps can be changed can be set here. The colour temperature range s restrcted to the physcal upper and lower lmts. Mnmum colour temperature: the warmest colour temperature that a lamp can have. Ths temperature s ether the physcal lower lmt or s cooler than ths lmt. Maxmum colour temperature: the coolest colour temperature that a lamp can have. Ths temperature s ether the physcal upper lmt or s warmer than ths lmt. Settng the mnmum or maxmum colour temperature 1. Set the value for the ndvdual parameter usng the slder. 2. Clck on save. Changes are stored n the devce. The mnmum colour temperature cannot be lower than the physcal lower lmt. The maxmum colour temperature cannot be hgher than the physcal upper lmt. Automatc calbraton The xy-coordnates for all supported prmares can be calbrated here. Carryng out automatc calbraton Clck on Start. Automatc calbraton begns. It lasts approxmately 15 mnutes. If calbraton s completed successfully, the status of the automatc calbraton s dsplayed n the Status tab as successful. If calbraton was not successful, the values from the last successful calbraton are automatcally loaded. If Stop s clcked durng automatc calbraton, calbraton s cancelled and the values of the last successful calbraton are loaded. 194

195 The current status of ths functon can be seen n the Status tab. Immedate colour change Users can set whether the colour can be mmedately changed or only usng an Actvate command here. These commands nclude Intensty (DAP), Brghten, Dm and Recall scene X. The fade tme for the ndvdual command s used. Dsablng mmedate colour change 1. Dsable the Colour only changes wth the "Actvate" command checkbox. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Status tab. 195

196 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control gear Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. 196

197 Power On Level Indcates whether the DALI control gear has gone to the Power On Level. Table 87: DALI control gear status nformaton Status of control gear for colour converters (DT 8) Status Descrpton xy-coordnates outsde value range Indcates whether values were chosen for the xy-coordnates whch are outsde of the value range. The confgurable value range depends on the LED module connected to the colour converter. Colour temperature outsde value range Indcates whether a value was chosen for the colour temperature whch s outsde of the value range. The confgurable value range depends on the LED module connected to the colour converter. Automatc calbraton n progress Indcates whether the automatc calbraton s stll ongong. Automatc calbraton successful Indcates whether the automatc calbraton was successful. If t was not successful, the values from the last successful calbraton are automatcally loaded. Colour type "xy-coordnates" actve Indcates whether the "xy-coordnates" colour type s enabled. Colour type "Colour temperature" actve Indcates whether the "colour temperature" colour type s enabled. Colour type "Prmary" actve Indcates whether the "prmary" colour type s enabled. Colour type "RGBWAF" actve Indcates whether the "RGBWAF" colour type s enabled. Table 88: Devce-specfc status nformaton for DALI control gear for colour converters 197

198 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. Specal features Number of prmares: If the prmares colour type s supported, the number of prmares s dsplayed. Number of RGBWAF channels: If the RGBWAF colour type s supported, the number of RGBWAF channels s dsplayed. 198

199 Trdonc-specfc confguraton All Trdonc-specfc functons and status nformaton can be found n the Trdonc-specfc confguraton pop-up wndow. Not every control gear element supports all functons. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Open the Trdonc-specfc confguraton pop-up wndow 1. In the DALI devce tree dagram, rght-clck on the DALI control gear to be confgured. The context menu appears. 2. Select Trdonc-specfc confguraton n the context menu. The Trdonc-specfc confguraton pop-up wndow opens. -ordouble-clck the DALI control gear to be confgured n the DALI devce tree dagram. The Trdonc-specfc confguraton pop-up wndow opens. 199

200 Devce operatng mode The devce operatng mode used by the control gear n order to carry out ts functons can be set here. Devce operatng mode Descrpton Automatc detecton The control gear detects the ncomng sgnal and swtches automatcally to the correspondng devce operatng mode. The followng devce operatng modes are automatcally detected: DALI only DSI only swtchdim only DALI and SMART DSI and SMART swtchdim and SMART corrdorfunction DALI only The control gear detects only DALI commands. DSI only The control gear detects only DSI commands. swtchdim only The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches. The mans voltage s used as a control sgnal. The control gear nterprets the sgnal as ether a smooth adjustment or swtch command dependng on how long the manual momentary-acton swtch s pressed. SMART only The lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DALI and SMART The control gear detects only DALI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. DSI and SMART The control gear detects only DSI commands and the lumnares connected to the control gear can only be smoothly adjusted usng a SMART nterface. swtchdim and SMART The lumnares connected to the control gear can only be smoothly adjusted usng manual momentary-acton swtches or va the SMART nterface. corrdorfunction Functon used to automatcally adjust the llumnance n an area (e.g. underground car park, underground walkways for pedestrans). When a moton sensor detects movement, the lghtng swtches to the presence value. When absence s detected, the lghtng swtches to the absence value. Then the lghtng s swtched off or stays at the absence value (dependng on requrements and settngs). There are four types of corrdorfunction: 200

201 corrdorfunction wth fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wth fade-n tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 4) Swtch-off delay corrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay corrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presence value B) Absence value 2) Run-on tme 4) Swtch-off delay Table 89: Devce operatng modes The DALI and SMART, DSI and SMART and swtchdim and SMART devce operatng modes are not supported by the control gear for fluorescent lamps belongng to the xtec II seres. 201

202 corrdorfunction parameters The followng table gves a descrpton of the ndvdual parameters for the corrdorfunction: Confguraton opton Descrpton Presence value Value to whch the lumnare group swtches when presence s detected n the room. Value range: 0 100% Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Value range: 0 100% Fade-n tme Tme requred to reach the presence value. Value range: fast s Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. The run-on tme can be confgured on the moton sensor. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Table 90: Overvew of corrdorfunction parameters 202

203 Commssonng date The commssonng date can be saved once n the control gear. Settng the commssonng date 1. The current day s marked n blue on the calendar. 2. Clck on save. Changes are stored n the devce. The date can only be set once. If the date has already been set, the commssonng date wll be dsplayed. 203

204 Compatblty settngs The generaton wth whch the control gear s compatble can be set here. Dependng on the compatblty settngs supported by the control gear, the followng optons are avalable: current generaton (n): the control gear uses the settngs for the current generaton. precedng generaton (n-1): the control gear uses the settngs for the precedng generaton (n-1). pre-precedng generaton (n-2): the control gear uses the settngs for the generaton before last (n-2). A detaled descrpton of whch parameters are changed (e.g. Mnmum level, Fade tme), can be found n the product documentaton for the correspondng control gear. Selectng compatblty settngs 1. Select the compatblty settng n the dropdown lst. 2. Clck on save. Changes are stored n the devce. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. 204

205 Features The behavour n DC mode, epower On Level and preheatng tme can be set for the ndvdual control gear element n the Features tab. Behavour durng DC operaton The control gear can be set to recall a fxed control value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. can be smoothly adjusted or swtched on/off) here. Settng behavour durng DC operaton 1. Enter the release code. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Normal operaton. 3. Clck on save. Changes are stored n the devce.. The release code can be obtaned from your sales partner. The current status of ths functon can be seen n the Trdonc-specfc confguraton pop-up wndow n the Status tab. epower On Level Here users can set whether the Power On Level (value after power has been restored) s overwrtten by an ed command. The epower On Level can be set to swtch the control gear to a fxed control value (0 100 %) or recall the memory value after power has been restored followng a falure. The memory value s the last control value to whch the control gear was set before the power falure. 205

206 Settng epower On Level 1. Enable the Enable epower On Level checkbox. The nput felds can be edted. 2. Select Fxed control value and enter the desred control value. -orselect Memory value. 3. Clck on save. Changes are stored n the devce. Preheatng tme The control gear can be set to gnore the preheatng tme and mmedately swtch on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme checkbox. 2. Clck on save. Changes are stored n the devce. 206

207 Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. Status Descrpton Normal operaton durng DC operaton Indcates whether the control gear contnues n normal operaton durng DC operaton,.e. can be smoothly adjusted and swtched on/off. Compatblty Indcates the compatblty settng used by the control gear. Intellgent Temperature Guard (ITG) Indcates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght control Indcates whether the ambent lght control s enabled or dsabled. Supply voltage Indcates the supply voltage wth whch the control gear s operatng. Overvoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an overvoltage. When overvoltage s detected, the lamps connected to the control gear flash n alternatng successon. 207

208 Undervoltage Indcates whether the Intellgent Voltage Guard (IVG) has detected an undervoltage. When voltage under 70 V s detected, the lamps connected to the control gear swtch off. When voltage between 70 and 140 V s detected, the lamps connected to the control gear swtch on and off at rregular ntervals. SMART sensor connected Indcates whether a SMART sensor s connected and that no error has occurred. Yes: SMART sensor connected and no error No: no SMART sensor connected, or SMART sensor connected but error has occurred Slave mode actve Indcates whether the slave mode s enabled. In slave mode the sensor s connected to two devces smultaneously and cannot be confgured. The sensor only responds to commands from the master devce. LED temperature montorng (ITM) actve Indcates whether the LED temperature montorng (ITM) functon s enabled. ITM fault Indcates whether a short crcut has occurred for the temperature sensor used for LED temperature montorng (ITM). Table 91: Status nformaton 208

209 Overvew of functons The Overvew of functons tab shows all functons supported by control gear of ths devce type. The Overvew of functons tab s only vsble f advanced settngs have been enabled. Not every control gear element supports all functons. For ths reason the functons are shown wth the followng symbols: Ths functon s supported by the control gear. Ths functon s not supported by the control gear. Types of functons The followng types of functons are avalable: Confgurable functons Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Functons wth dsplayed statuses Ths functons cannot be confgured. Statuses are shown n the Status tab. Confgurable functons wth dsplayed statuses Functons are confgured n the detal vew, ether n the Basc confguraton tab or n a devce-specfc tab. Statuses are shown n the Status tab. 209

210 8.1.8 Devce Type 255: Mult-devce types Mult-devce types are shown n the DALI devce tree dagram wth the symbol and the short descrpton Mult. They comprse at least two devce types. There are several combnatons avalable. The confguraton optons for the mult-devce type depend on the confguraton optons for the ndvdual devce types whch make up the mult-devce type. The followng mult-devce types are currently supported: TALEXXmodule STARK DLE LCAI TuWh Lnear Devce type 6: control gear for LEDs 150 Devce type 8: control gear for colour converters 187 Devce type 6: control gear for LEDs 150 Devce type 8: control gear for colour converters

211 8.2 DALI XC The DALI XC s represented n the DALI devce tree dagram by the con and the short name DALI XC. When addressng, the DALI XC s gven an ed address (ea) and can be confgured n the detal vew usng ths address. The masterconfigurator software uses the countng method gven n DALI standard IEC Addresses, groups and scenes are counted startng wth 0. However there are devces that are counted startng wth 1, e.g. DALI XC. If scene 1 s selected va a rotary selector swtch, for example, t s dsplayed n the masterconfigurator software as scene 0. Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the devce. Artcle number Dsplays the artcle number of the devce. Seral number Dsplays the unque seral number of the devce. Date of manufacture (CW.YYYY) Dsplays the date of manufacture of the devce n the format CW.YYYY (calendar week, year). Frmware verson Dsplays the frmware verson of the devce. ed verson Dsplays the verson of the ed specfcaton supported by the devce. ed s an enhanced protocol based on DALI connectons. Table 92: Devce nformaton 211

212 8.2.1 Basc confguraton The power on behavour can be set and the current confguraton of the DALI XC can be vewed n the Basc confguraton tab. Power on behavour The power on behavour ndcates how the DALI XC responds after the voltage supply has faled. The power on behavour can be confgured n all operatng modes. Command Indcates whch command the DALI XC sends to all of the lumnares connected to the DALI control lne after the power s restored: Off Recall scene X (0 15) Do not send command: If more than one DALI XC s connected to the DALI control lne, the power on behavour can only be set on one DALI XC. Do not send command must be set for all other DALI XC devces. Delay tme Tme after whch the selected command s sent. Value range: 0 7 s Table 93: Confguraton optons for "pow er on behavour" 212

213 "Mode" and "Confg" rotary selector swtches There are two rotary selector swtches on the DALI XC. (1) Mode rotary selector swtch The operatng mode of the DALI XC can be set va ths rotary selector swtch. (2) Confg rotary selector swtch The nputs of the DALI XC can be confgured va ths rotary selector swtch. Operatng modes The DALI XC has seven operatng modes (A G), whch are set va the Mode rotary selector swtch. Rotary selector swtch poston Descrpton Confguraton A MC operatng mode: Programmed functons can be recalled va sngle momentaryacton swtches and/or double momentary-acton swtches and/or standard swtches. Ths operatng mode s confgured va the masterconfigurator software. Rotary selector swtch Confg (2) has no functon here. For a detaled descrpton of the settng optons, see Secton Confguraton of operatng mode "MC" B SC-A operatng mode: Scenes can be recalled va sngle momentary-acton swtches. Ths operatng mode s confgured va rotary selector swtch Confg (2) on the DALI XC. A scene s assgned to each of the four nputs. The settngs are dsplayed n the masterconfigurator software. C SC operatng mode: Scenes can be recalled and saved va sngle momentary-acton swtches. Ths operatng mode s confgured va rotary selector swtch Confg (2) on the DALI XC. A scene s assgned to each of the four nputs. The settngs are dsplayed n the masterconfigurator software. D GC-A operatng mode: Lumnare groups can be swtched on and off and dmmed and brghtened va sngle momentaryacton swtches and/or double Ths operatng mode s confgured va rotary selector swtch Confg (2) on the DALI XC. A lumnare group s assgned to each of the four nputs. The settngs are dsplayed n the masterconfigurator software. 213

214 Rotary selector swtch poston Descrpton Confguraton momentary-acton swtches. E GC operatng mode: Lumnare groups can be swtched on and off, dmmed and brghtened, and grouped va sngle momentaryacton swtches and/or double momentary-acton swtches. Ths operatng mode s confgured va rotary selector swtch Confg (2) on the DALI XC. A lumnare group s assgned to each of the four nputs. The settngs are dsplayed n the masterconfigurator software. F PROG operatng mode: Commssonng or a system extenson can be started and completed n ths operatng mode. The control ponts for ths DALI XC are locked. All other DALI XC devces can be operated as normal. Ths operatng mode s confgured va rotary selector swtch Confg (2) on the DALI XC. A lumnare group s assgned to each of the four nputs. The settngs are dsplayed n the masterconfigurator software. G TuWh operatng mode: The ntensty and colour temperature of Tunable Whte lumnares can be set va double momentary-acton swtches. Ths operatng mode s confgured va rotary selector swtch Confg (2) on the DALI XC. A lumnare group s assgned to each of the four nputs. The settngs are dsplayed n the masterconfigurator software. Table 94: Operatng modes of the DALI XC 214

215 8.2.2 Confguraton of operatng mode "MC" In the MC operatng mode, sngle momentary-acton swtches and/or double momentary-acton swtches and/or standard swtches can be used to recall programmed functons. These functons are confgured va the masterconfigurator software. The Confg rotary selector swtch has no functon. The DALI XC has four nputs (T1 T4). The effectve range of the respectve nput and ts functon can be set n tabs T1, T2, T3 and T4. Confguraton opton Descrpton Effectve range Range controlled va the relevant nput (T1, T2, T3 or T4): All Group (0 15) Address (0 63) Functon Functon stored for the selected effectve range on the relevant nput (T1, T2, T3 or T4): No functon: The selected nput has no functon. Momentary-acton swtch: more nformaton can be found here Changeover swtch: more nformaton can be found here Standard swtch: more nformaton can be found here Macro: starwell functon More nformaton can be found here Macro: dynamc scene recall More nformaton can be found here Macro: sequental scene recall More nformaton can be found here Macro: user-defned command sequence More nformaton can be found here User-defned confguraton of the nputs: settngs stored on the DALI XC do not correspond to the settng optons n the masterconfigurator software. As soon as the system s swtched from functon User-defne confguraton of the nputs to another functon and ths s saved, the userdefned confguraton of the nputs s lost and cannot be restored. Table 95: Confguraton optons for "MC" operatng mode 215

216 Momentary-acton swtch The selected nput s confgured as a momentary-acton swtch. The followng confguraton optons are avalable for ths functon: Confguraton opton Descrpton Brefly press momentary-acton swtch Brefly pressng the momentary-acton swtch wll send command X1 one tme. The followng commands can be selected from the dropdown lst for command X1: Ignored Intensty (DAP): n percent Off Maxmum level Mnmum level Recall scene X (0 15) A fade tme can also be stored dependng on the command. For a precse descrpton of the DALI commands, see Secton DALI commands

217 Confguraton opton Descrpton Hold down momentary-acton swtch Holdng down the momentary-acton swtch wll send command Y1. The commands are repeatedly sent for as long as the momentary-acton swtch s held down. The followng commands can be selected from the dropdown lst for command Y1: Ignored Brghten Dm Increase colour temperature Decrease colour temperature A fade rate can also be stored dependng on the command. For a precse descrpton of the DALI commands, see Secton DALI commands Table 96: Confguraton optons for the "momentary-acton sw tch" functon To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 217

218 Changeover swtch The selected nput s confgured as a changeover swtch. Each tme the momentary-acton swtch s brefly pressed command X1 and command X2 are sent n alternatng sequence. Each tme the momentaryacton swtch s held down command Y1 and command Y2 are sent n alternatng sequence. The command sent each tme depends on the lghtng status and s automatcally selected by the DALI XC. The followng confguraton optons are avalable for ths functon: Confguraton opton Descrpton Brefly press momentary-acton swtch Each tme the momentary-acton swtch s brefly pressed command X1 and command X2 are sent n alternatng sequence. The followng commands can be selected from the dropdown lst for command X1 and command X2: Ignored Intensty (DAP): n percent Off Maxmum level Mnmum level Recall scene X (0 15) For a precse descrpton of the DALI commands, see Secton DALI commands

219 Confguraton opton Descrpton Hold down momentary-acton swtch Each tme the momentary-acton swtch s held down command Y1 and command Y2 are sent n alternatng sequence. The commands are repeatedly sent for as long as the momentary-acton swtch s held down. The followng commands can be selected from the dropdown lst for command Y1: Ignored Brghten Increase colour temperature The followng commands can be selected from the dropdown lst for command Y2: Ignored Dm Decrease colour temperature For a precse descrpton of the DALI commands, see Secton DALI commands Table 97: Confguraton optons for the "changeover sw tch" functon To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 219

220 Standard swtch The selected nput s confgured as a standard swtch. The followng confguraton optons are avalable for ths functon: Confguraton opton Descrpton Lghtng-lnked The command sent each tme depends on the lghtng status and s automatcally selected by the DALI XC. Close If the standard swtch s confgured to be lghtnglnked, no fade tme can be stored for command X1 and command Y1. When the swtch s closed, command X1 s sent one tme. The followng commands can be selected from the dropdown lst for command X1: Ignored Intensty (DAP): n percent Off Maxmum level Mnmum level Recall scene X (0 15) 220

221 A fade tme can also be stored dependng on the command. Open For a precse descrpton of the DALI commands, see Secton DALI commands When the swtch s opened, command Y1 s sent one tme. The followng commands can be selected from the dropdown lst for command Y1: Ignored Intensty (DAP): n percent Off Maxmum level Mnmum level Recall scene X (0 15) A fade tme can also be stored dependng on the command. For a precse descrpton of the DALI commands, see Secton DALI commands Table 98: Confguraton optons for the "standard sw tch" functon To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 221

222 Macro: starwell functon A momentary-acton swtch or standard swtch s pressed n a starwell, whch swtches on the lghtng wth command X1 and starts the run-on tme. If no one presses a momentary-acton swtch or standard swtch agan durng the run-on tme, command Y1 s then sent. The followng confguraton optons are avalable for ths functon: Confguraton opton Descrpton Brefly press momentary-acton swtch When the momentary-acton swtch or standard swtch s pressed, command X1 s sent one tme. The followng commands can be selected from the dropdown lst for command X1: Ignored Intensty (DAP): n percent Off Maxmum level Mnmum level Recall scene X (0 15) A fade tme can also be stored dependng on the command. 222

223 Confguraton opton Descrpton Run-on tme For a precse descrpton of the DALI commands, see Secton DALI commands Tme that starts when the lghtng s swtched on and after whch command Y1 s sent. If someone presses a momentary-acton swtch or standard swtch agan n ths starwell durng the run-on tme, the run-on tme starts agan. Value range: 1 s 60 mn None After run-on tme has expred After run-on tme has expred, command Y1 s sent one tme. The followng commands can be selected from the dropdown lst for command Y1: Ignored Intensty (DAP): n percent Off Maxmum level Mnmum level Recall scene X (0 15) A fade tme can also be stored dependng on the command. For a precse descrpton of the DALI commands, see Secton DALI commands Table 99: Confguraton optons for the "starw ell functon" To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 223

224 Macro: dynamc scene recall A dynamc scene recall conssts of no more than 16 scenes that are automatcally recalled one after the other. The order of the scenes can be selected freely. Scenes may occur more than once n a dynamc scene recall. A fade tme and hold tme are defned for each scene. Brefly pressng the momentary-acton swtch connected to the nput starts the dynamc scene recall; one scene after the other s recalled. Brefly pressng the momentary-acton swtch agan nterrupts the dynamc scene recall. The last scene recalled remans actve. Brefly pressng the momentary-acton swtch agan contnues the dynamc scene recall. Holdng down the momentary-acton swtch stops the dynamc scene recall and sends an off command. The followng confguraton optons are avalable for ths functon: Confguraton opton Descrpton Repeat all When the last scene s recalled, the scene recall starts agan wth the frst scene. If the dynamc scene recall s not repeated, the last hold tme runs ndefntely and the scene s not swtched. Fade tme The tme t takes to change from one scene to the next. Value range: fastest s : 90.5 s s the slowest fade tme. 224

225 Confguraton opton Descrpton Scene Scene beng recalled. Scenes can be used repeatedly wthn a dynamc scene recall. Value range: Scene X (0 15) Hold tme Tme for whch the set scene s held. Once the hold tme expres, the next scene s recalled wth the defned fade tme. Value range: 1 s 60 mn Ignore: the set fade tme and scene are gnored. Ths settng s used when a scene needs to be removed from a dynamc scene recall that s already defned, wthout havng to reconfgure the entre dynamc scene recall. Table 100: Confguraton optons for the "macro: dynamc scene recall" functon To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 225

226 Macro: sequental scene recall A sequental scene recall conssts of no more than 16 scenes. The order of the scenes cannot be nfluenced. An off command can be sent to the set effectve range after the last scene f desred. Every tme the momentary-acton swtch connected to the nput s pressed, the next selected scene s recalled. Once all scenes have been recalled, the sequental scene recall starts agan from the start. To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. An off command from another devce sent to the set effectve range or an off command sent to all control gear connected to the control lne s nterpreted by the DALI XC as such and the sequental scene recall s stopped. The sequental scene recall starts agan from the start the next tme a momentary-acton swtch s pressed. 226

227 Macro: user-defned command sequence A *.cot fle created by the user wth user-defned commands s loaded. Every tme the momentary-acton swtch connected to the nput s pressed, the user-defned command sequence s recalled. The *.cot fle can be created wth the command admnstrator. A detaled descrpton of the command admnstrator can be found n Secton Command admnstrator Defnton of the *.cot fle The effectve range must be defned n the *.cot fle. The *.cot fle can contan maxmum 20 commands. The delay tme for sendng the commands must be 20 ms. If a dfferent tme s defned for sendng the commands, the masterconfigurator software gnores ths nformaton and uses 20 ms nstead. To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 227

228 8.2.3 Status The Status tab shows all status nformaton whch can be quered by the DALI XC. General status of the DALI XC Status Descrpton Ready Indcates whether the DALI XC s ready for communcaton. Fault on at least one nput Indcates whether a fault exsts on at least one nput. At least one nput locked: Indcates whether at least one nput s locked from operaton. At least one swtch frozen To fnd out whch nputs are affected, press each nput n order. Status Input Tx pressed shows the nput on whch a fault exsts. The ed commands can be used to lock and unlock nputs from operaton. Indcates whether at least one swtch s frozen. Table 101: Status nformaton for the DALI XC 228

229 Status of the nputs of the DALI XC Status Descrpton Input T1 Indcates whether the momentary-acton swtch or standard swtch connected to nput T1 s currently pressed. Input T2 Indcates whether the momentary-acton swtch or standard swtch connected to nput T2 s currently pressed. Input T3 Indcates whether the momentary-acton swtch or standard swtch connected to nput T3 s currently pressed. Input T4 Indcates whether the momentary-acton swtch or standard swtch connected to nput T4 s currently pressed. Table 102: Status nformaton for the DALI XC 229

230 8.3 DALI MC The DALI MC s represented n the DALI devce tree dagram by the vew. con and s confgured n the detal The DALI MC has four ndependent nputs. To make t possble to parameterse these nputs freely, each of the four nputs must have ts own edali address (ea). Confguraton opton Descrpton Power on behavour Specfes how the DALI MC behaves when power s restored: do not send command OFF Scene 0 15 Delay tme Tme after whch the selected command s sent. The delay tme s used to take nto account the start-up tme of the DALI control gear after power s restored. Table 103: Confguraton optons for the DALI MC The behavour when power s restored can only be set va the detal vew of nput T4. Ths functon s not avalable for any of the other nputs. 230

231 Parametersng the nputs Requrement: Each DALI MC nput has ts own edali address (ea). 1. In the DALI devce tree dagram, select a DALI MC nput. The confguraton s dsplayed n the detal vew. 2. From the Target drop-down lst, select the destnaton address to whch the command s to apply: All, Group 0 15 or ndvdual Address. 3. From the Confgure functon drop-down lst, select a functon or macro. 4. Defne the functon va nput felds, lsts and rado buttons. 5. Clck on Save. The confguraton s saved n the DALI MC. The saved confguraton can now be tested drectly n the feld. Functons In the Confgure functon drop-down lst, choose between the followng functons: Functon Descrpton 1) Push-button: short or long = 1 * command X Brefly pressng or holdng down the push-button wll send command X one tme. 2) Push-button: short = 1 * command X, long = 1 * command X then 1 * command Y Brefly pressng the push-button wll send command X one tme. Holdng down the push-button wll send command X once, and then command Y once. 3) Push-button: short = 1 * command X, long = 1 * command X then repeatedly command Y Brefly pressng the push-button wll send command X one tme. Holdng down the push-button wll send command X once, and then command Y repeatedly. 4) Push-button: short = 1* command X, long = repeatedly command Y Brefly pressng the push-button wll send command X one tme. Holdng down the push-button wll repeatedly send command Y. 5) Push-button (toggle): short or long = toggle between command X and Y Brefly pressng or holdng down the push-button wll alternate between sendng commands X and Y. 6) Push-button (toggle): short or long = toggle between command X and Y, lghtng-based Brefly pressng or holdng down the push-button wll alternate between sendng commands X and Y. The command sent n each case depends on the status of the lghtng: If the lghtng was prevously swtched off, command X s sent. If the lghtng was prevously swtched on, command Y s sent. 231

232 7) Push-button (dmmng key): short = toggle between command X and Y, long = dmmng, lghtng-based 8) Swtch: close = command X, open = command Y SwtchDIM mode Brefly pressng on the dmmng key wll alternate between sendng commands X and Y. The command sent n each case depends on the status of the lghtng. If the lghtng was prevously swtched off, command X s sent. If the lghtng was prevously swtched on, command Y s sent. Holdng down the dmmer swtch dms or brghtens the lghtng. When the swtch s closed, command X s sent. When the swtch s opened, command Y s sent. 9) Changeover swtch: close = command X, open = command Y, lghtng-based Each tme the swtch s pressed, the commands X and Y are sent n alternatng order. The command sent n each case depends on the status of the lghtng: If the lghtng was prevously swtched off, command X s sent. If the lghtng was prevously swtched on, command Y s sent. 10) Starwell functon: close = command X, start run-on tme, run-on tme elapsed = command Y If the push-button s pressed, command X s sent and the run-on tme starts. Once the run-on tme has elapsed, command Y s sent. Table 104: DALI MC functons Commands X and Y represent varables. The followng commands can be selected: Intensty (DAP) Off Down Step up Step down Recall max Recall mn Step down and off On and Step up Go to Scene X (0 15) No functon For a precse descrpton of the DALI commands, see Secton DALI commands

233 Macros In the Confgure functon drop-down lst, choose between the followng macros: Macro 1: Go home Functon Dm off lumnare wthn a defned tme. Adjustable parameters Fade tme: tme requred to reach the absence level. Reset fade tme: tme requred to reach the presence level agan. Table 105: DALI MC macro 1: Go home Macro 2: MSensor automatc Functon Ambent lght control of the DALI MSensor s enabled. Target The destnaton address of the macro s ether All or the edali (ea) of the approprate DALI MSensor. Table 106: DALI MC macro 2: MSensor automatc Macro 3: Sequental scene recall Functon Every tme the push-button connected to the nput s pressed, the next scene s recalled. At the end of the sequence, the process begns agan. Adjustable parameters Scenes 0 15: selecton of scenes to be recalled. Off: selecton of whether an off command s to be sent at the end of the sequence. Table 107: DALI MC macro 3: Sequental scene recall The order of the scenes cannot be nfluenced. The scenes are always recalled n ascendng order. 233

234 Macro 4: Dynamc scene Functon Pressng the push-button recalls a sequence of four scenes. The fade tme and delay tme can be defned freely for each scene. Sequence Press the push-button brefly: the sequence starts. Brefly press the push-button wth scene runnng: the sequence stops. Hold down the push-button wth scene runnng: sequence s stopped and an off command s sent. Adjustable parameters Delay tme: delay tme before the scene s recalled. Ths can be between 0 and 255 seconds. The delay tme for the next scene s therefore the dwell tme for the precedng scene. Fade tme: fade tme for the new scene. Scene: selecton of whch scene s to be recalled. Repeat: when the last scene s reached, the sequence starts agan wth the frst scene. Table 108: DALI MC macro 4: Dynamc scene The delay tme before the frst scene only comes nto effect when the sequence s repeated, snce t s the dwell tme of the fourth scene and wll only start rght before the frst scene s recalled. It s gnored when the sequence s started wth the push-button. Macro 5: DALI reset Functon Reset for defned devces. Optonally, the addresses may also be deleted. The followng parameters are reset to the reset values: Group and scene settngs Maxmum level, mnmum level Power on level, system falure level Fade tme, fade rate If the DALI control gear possesses other parameters (e.g. epower on level on the PCA lp), they are not reset. Adjustable parameters addtonally delete addresses: the devces are reset and the addresses are deleted. Table 109: DALI MC macro 5: DALI reset The reset values can be found n Secton Reset values

235 Macro 6: e-power ON level Functon Sets the power-on level of the DALI control gear to the defned value. DALI devces whch do not support ths functon wll gnore the command. Adjustable parameters Memory value: sets the power-on level to the value before power falure (memory value). user-defned: the power-on level s shown as a percentage. In addton, a fade tme can be defned. Table 110: DALI MC macro 6: e-pow er ON level Macro 7: PCA compatblty Functon Sets the PCA compatblty parameter n the PCA EXCEL one4all devces to the defned value. DALI devces whch do not support ths functon wll gnore the command. Table 111: DALI MC macro 7: PCA compatblty Macro 8: User-defned DALI commands Functon Executes a *.cot fle that can be created by the user. The followng ponts must be observed: The *.cot fle must not exceed the lmt of 10 commands. The destnaton address must be specfed n the *.cot fle. The delay tme from one command to another s set to 20 ms and cannot be changed. Table 112: DALI MC macro 8: User-defned DALI commands 235

236 8.4 DALI bascdim DGC DALI bascdim DGC s represented n the DALI devce tree dagram by the detal vew. con and s confgured n the DALI bascdim DGC conssts nternally of three devce classes, whch are lsted ndvdually n the DALI devce tree dagram: Lght sensor: A detaled descrpton of the lght sensor can be found n Secton DALI bascdim DGC Lght sensor 244. Moton sensor: A detaled descrpton of the moton sensor can be found n Secton bascdim DGC Moton sensor 245. Remote control: A detaled descrpton of the remote control can be found n Secton bascdim DGC Remote control 249. Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the control gear. Lamp type Dsplays the lamp type of the lamp connected to the control gear. Artcle number Dsplays the artcle number of the control gear. Seral number Dsplays the unque seral number of the control gear. Date of manufacture Dsplays the date of manufacture for the control gear. Frmware verson Dsplays the frmware verson of the control gear. DALI verson Dsplays the verson of the DALI specfcaton supported by the control gear. ed verson Dsplays the verson of the ed specfcaton supported by the control gear. ed s an enhanced protocol based on DALI connectons. Table 113: Devce nformaton 236

237 8.4.1 Basc confguraton The group assgnment for control gear can be vewed and scenes and default DALI parameters can be set for each control gear element n the Basc confguraton tab. Member of group(s) Member of group(s) specfes the group or groups to whch the control gear belongs. These groups are ndcated by the blue background. Scenes The ntensty of the dfferent outputs can be set for all 16 scenes (0 15) here. Settng scenes 1. Enable the checkbox for a scene, n order to assgn an ntensty to the lumnare. The nput feld can be edted. 2. For Output 1 and Output 2: Enter a value between 0 % and 100 %. 3. For Relay output: Enter off, on or MASK. 4. To defne settngs for addtonal scenes, repeat steps 1 and Clck on save. Changes are stored n the devce. MASK means that the lumnare n ths group wll retan ts current ntensty when the relevant scene s recalled. 237

238 DALI default parameters DALI default parameters can be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clck on save. Changes are stored n the devce. The followng DALI default parameters can be set: DALI default parameters Descrpton Fade tme The selected value s set as the fade tme n seconds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Mnmum level The selected value s set as the mnmum level for the control gear. Ths value cannot be fallen below durng dmmng/ brghtenng. Value range: Physcal lower lmt Maxmum level : The physcal lower lmt of the control gear s shown to the rght of the Mnmum level as a percentage. The mnmum level must be above ths value. Maxmum level The selected value s set as the maxmum level for the control gear. Ths value cannot be exceeded durng dmmng/ brghtenng. Value range: Mnmum Level 100% Table 114: DALI default parameters To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 238

239 8.4.2 Room profles In the Room profles tab you can choose and actvate a room profle. The followng fve room profles are avalable: Image Profle name Descrpton Indvdual room Two llumnaton areas (wndows area, rest of the room ), two swtches, moton sensor(s) Swtch 1 operates the lghtng of the wndows area, swtch 2 operates the lghtng of the rest of the room. Classroom Three llumnaton areas (wndows area, rest of the room, separate presentaton area), two swtches, moton sensor(s) Swtch 1 operates the lghtng of the wndows area and the rest room of the room together (rato of the two dmmng levels remans the same), button 2 operates the presentaton area. Corrdor One llumnaton areas, swtches, moton sensor(s) Swtches operates the lghtng of all the lumnares. Dfferent dmmng levels can be defned for presence detecton n another room (neghbourhood functon), for presence detecton n the corrdor tself and for the absence of any presence detecton. WC Two llumnaton areas (snk and mrror area, tolet area ), two swtches, moton sensor(s) Swtch 1 operates the lghtng of the snk and mrror area, swtch 2 operates the lghtng of the tolet area. 239

240 Image Profle name Descrpton In connecton wth presence detecton dfferent dmmng levels can be defned for the two lghtng areas. Free-standng lumnare Two llumnaton areas (drect and ndrect lghtng ), two swtches, moton sensor(s) Swtch 1 controls drect lghtng, swtch 2 controls ndrect lghtng. If no presence s detected the freestandng lumnare s swtched off completely to avod stand by losses. Tabelle 115: Room profles of the DALI bascdim DGC Wth the neghbourhood functon presence detecton can be transfered from one room to another. By default the neghbourhood functon s deactvated. Clckng on Reset, resets the current profle to ts default values Devce-specfc confguraton If the checkbox Lock desred value has been actvated, the nomnal value cannot be changed va remote control or the momentary-acton swtch nput. Inputs 240

241 Confguraton opton Descrpton Effectve range: Range that s operated by momentary-acton swtch nput T1 and T2: Output 1 Output 2 Relay output Brefly press momentary-acton swtch Determnes the reacton of the lghtng when the momentaryacton swtch s brefly pressed: no functon only on only off on/off Hold down momentary-acton swtch Determnes the reacton of the lghtng when the momentaryacton swtch s held down: no functon brghten dm brghten/dm Double clck the momentary-acton swtch Determnes the reacton of the lghtng when the momentaryacton swtch s double clcked: no functon save desred value Table 116: Confguraton optons for the "momentary-acton sw tch" functon Output 1, 2 and relay Confguraton opton Descrpton Output 1 and output 2 Determnes the settngs for output 1 and output 2: both outputs: DSI both outputs: DALI output 1: DALI; output 2: lnkng output 1: DSI; output 2: lnkng Dfference from output 2 to output 1: Determnes the dfference from output 2 to output 1: Range of values: -95% - +95%, adjustable n 5% steps 241

242 Confguraton opton Descrpton Operatng Determnes the settngs for the operaton mode: energy-savng mode va PIR: only ON va PIR: only OFF va momentary-acton swtch: ON/OFF Delay tme: Determnes the settngs for the delay tme. (In energy-savng mode the contact s opened after the delay tme) Range of values: 1-30 mn, default: 10 mn Table 117: Confguraton optons for the "momentary-acton sw tch" functon Status The Status tab shows all status nformaton whch can be quered by the control gear. An overvew of whch functons are supported by the control gear can be found n the Overvew of functons tab. Ths tab s only vsble f advanced settngs have been enabled. General status of control module Status Descrpton Ready Indcates whether the DALI control gear s ready for communcaton. Lamp falure Indcates whether a lamp falure (short crcut, open crcut, load decrease or load ncrease) has occurred. Lamp on Indcates whether the lamp s on. Lmt volaton Indcates that the lumnare was unable to swtch to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme actve Indcates whether a devce s changng from one control value to another. Reset values Indcates whether the DALI control gear has been reset to the reset values. Address mssng Indcates whether the DALI control gear s unaddressed. Power On Level Indcates whether the DALI control gear has gone to the 242

243 Power On Level. Table 118: Status nformaton of the control module 243

244 8.4.5 Lght sensor If several sensors are conntected to the DALI bascdim DGC, all these sensors have the same settngs. Confguraton optons n drect master mode The followng confguraton optons are dsplayed for the lght sensor n drect master mode: Confguraton opton Descrpton Ambent lght control output 1: Ambent lght control can be enabled or dsabled. Ambent lght control output 2: Avalable optons: not enabled connected to output 1 Desred value: Value used by the lght sensor to regulate the control gear. On account of the room condtons and the nstallaton heght, the llumnance n the workspace may, however, be three to four tmes hgher. Value range: lx Control speed: Speed at whch the control gear reaches the desred value. 244

245 Value range: ncrements 0 7, wth 0 beng the slowest and 7 the fastest. Automatc control: Indcates the scene used to control the lghtng based on whether presence s detected. If ths scene s recalled the moton sensor s enabled and the lumnares are controlled based on whether presence s detected. Value range: Scene 0-15 The scene selected here s dentfed n the Basc confguraton as automatc. Response to manual dmmng: Avalable optons: dsable ambent lght control permanent desred value change temporary desred value change Enable dmmng off (brght out) Checkbox enabled: f the measured llumnance exceeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swtched off even f moton s detected n the room. As soon as the measured llumnance falls below the desred value, the lumnare group s swtched on agan. Dsplay flashng pattern on sensor status LED: Checkbox enabled: Devce status s dsplayed by a flashng pattern on sensor status LED. Threshold Value above whch the lumnare group s swtched off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whch the threshold must be exceeded n order for the lumnare group to be swtched off by the lght sensor. Value range: mn Table 119: Lght sensor confguraton optons n drect master mode Moton sensor If several sensors are conntected to the DALI bascdim DGC, all these sensors have the same settngs. 245

246 Confguraton optons Confguraton opton Descrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatcally swtched on and off dependng on whether presence s detected. (factory settng) enabled (only OFF): the moton sensor swtches the lghtng off only. It must be swtched on manually. dsabled: the moton sensor s dsabled. The lghtng must be swtched on and off manually. : The never OFF functon s mplemented as follows: 1. Select the enabled operatng mode. 2. Select swtch-off delay never OFF. Power on behavour Indcates how the moton sensor wll react after falure of the DALI power supply: Standby presence value Fade-n tme Tme requred to reach the presence value. Value range: fast 246

247 s Presence value Value to whch the lumnare group swtches when presence s detected n the room. Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. Value range: 30 s - 60 mn adaptve: The adaptve run-on tme adapts the length of the run-on tme automatcally (between 4 and 20 mn.) The length s calculated dependng on the number of presence detectons. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 60 mn never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Fade-out tme Tme requred to dm off from the absence value. Value range: fast s Dead tme (manual off) Tme started by manually swtchng off the lghtng va the momentary-acton swtch or the remote control and durng whch the moton sensor s dsabled. If movement s detected n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s detected n the room, the moton sensor s enabled agan. Value range: 0 s - 10 mn Send own presence as Value range: Group 0-15 Broadcast 247

248 Send own presence as defnes a unque group dentfer for the bascdim DGC. If the bascdim DGC transmts nformaton va the neghborhood functon, ths group dentfer s also transmtted. Response to presence detected by other bascdim DGC devces Ths settng determnes how the moton sensor responds when presence s detected n another group. Three groups n total can be confgured. MASK: the DALI MSensor 02 gnores the presence detected n another group (factory settng). Presence value: the lumnare group assgned to the DALI MSensor 02 swtches to the presence value. Absence value: the lumnare group assgned to the DALI MSensor 02 swtches to the absence value. Excepton: f the lumnares are already at the presence value, they retan ths settng. Dsplay flashng pattern on sensor status LED Checkbox enabled: Devce status s dsplayed by a flashng pattern on sensor status LED Table 120: Moton sensor confguraton optons n drect master mode To apply the changed values, clck on save. The saved confguraton can now be tested drectly n the feld. 248

249 8.4.7 Remote control Confguraton optons n drect master mode The followng devce nformaton s dsplayed for the remote control n drect master mode: Confguraton opton Descrpton Basc functon Operatng functons of the remote controls: nactve: the keys of the remote control are nactve. actve: the keys of the remote control are actve. Table 121: Remote control confguraton optons n drect master mode 8.5 DALI MSensor The masterconfigurator can be used to confgure the followng versons of the DALI MSensor: DALI MSensor 02 (verson 2.0) DALI MSensor (verson 1.5) 266 DALI MSensor (verson 1.3)

250 8.5.1 DALI MSensor 02 (verson 2.0) DALI MSensors are represented n the DALI devce tree dagram by the detal vew. con and are confgured n the DALI MSensor 02 conssts nternally of three devce classes, whch are lsted ndvdually n the DALI devce tree dagram: Lght sensor: A detaled descrpton of the lght sensor can be found n Secton DALI MSensor 02 (V2.0) > Lght sensor 253. Moton sensor: A detaled descrpton of the moton sensor can be found n Secton DALI MSensor 02 (V2.0) > Moton sensor 259. Remote control: A detaled descrpton of the remote control can be found n Secton DALI MSensor 02 (V2.0) > Remote control 263. Group concept The group assgnment for the DALI MSensor 02 s dsplayed. Lumnare group: DALI group (G) contanng the DALI MSensor 02. All devces n ths group are controlled by the DALI MSensor 02. The followng groups are also dsplayed f advanced settngs have been enabled: Lght sensor group: ed group (eg) contanng the lght sensor. Moton sensor group: ed group (eg) contanng the moton sensor. Remote control group: ed group (eg) contanng the remote control. Effectve range The DALI MSensor 02 controls ether all devces (broadcast) or one DALI group. Assgnment va the rotary swtch The effectve range of the DALI MSensor 02 s set usng the rotary swtch on the back of the sensor. All control gear elements n the set effectve range are controlled by the DALI MSensor 02. Poston of the rotary swtch on the DALI MSensor 02 Effectve range 0 All (broadcast) 1 Group 0 2 Group Groups 2 8 A F Groups 9 14 Table 122: Poston of the rotary sw tch on the DALI MSensor 02 and ts correspondng effectve range 250

251 Assgnment va the masterconfigurator When the DALI MSensor 02 s not assgned to a group n the DALI devce tree dagram, t controls the lumnare group set usng the rotary swtch on the back of the sensor. It must be assgned to a group to control an ndvdual group. 1. In the DALI devce tree dagram, clck on the DALI MSensor 02 to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the DALI MSensor 02 to the desred lumnare group. (Drag & Drop) The DALI MSensor 02 s removed from the ndvdual (non-grouped) secton of the DALI devce tree dagram and s added to the desred lumnare group. The poston of the rotary swtch on the back of the DALI MSensor 02 s gnored. If the group assgnment n the masterconfigurator s undone, the rotary swtch poston wll be actve agan. 251

252 Operatng modes The DALI MSensor 02 supports two operatng modes. The operatng mode can only be changed when the advanced settngs are enabled. Drect master mode (factory settng) Functon: Master Tasks: Send DALI commands to DALI control gear Send ed commands to other DALI MSensor 02 devces Addressng: The DALI MSensor 02 has one DALI address. The lght sensor, moton sensor and remote control each have one ed address. Slave mode Functon: Slave Tasks: Respond to DALI and ed commands from a master devce Addressng: The DALI MSensor 02 has one DALI address. The lght sensor, moton sensor and remote control each have one ed address. In slave mode the rotary swtch on the back of the DALI MSensor 02 does not have a functon. 252

253 Lght sensor The lght sensor supports two operatng modes: Drect master mode Slave mode: the lght sensor cannot be confgured n ths operatng mode. The lght sensor just responds to commands from the master devce. More nformaton on these operatng modes can be found n Secton DALI MSensor Drect master mode 253

254 Status n drect master mode The followng status nformaton s dsplayed for the lght sensor n drect master mode: Status Descrpton Illumnance Illumnance currently measured at the lght sensor. On account of the room condtons and the nstallaton heght, the llumnance n the workspace may, however, be three to four tmes hgher. Update status automatcally Indcates whether the lght sensor status s updated automatcally. Ambent lght control Indcates the status of ambent lght control for the lght sensor. enabled: ambent lght control s enabled. temporarly dsabled: ambent lght control has been temporarly dsabled manually by the user. dsabled: ambent lght control s dsabled. unknown: there s currently no connecton to the lght sensor. Reference devce Indcates the DALI control gear used as a reference for calculatng the swtch-on level durng ambent lght control. If no reference devce has been assgned to the lght sensor, no devce wll be dsplayed. : Secton Reference devce reference devce s assgned. 258 explans how a Table 123: Lght sensor status nformaton n drect master mode Confguraton optons n drect master mode The followng confguraton optons are dsplayed for the lght sensor n drect master mode: Confguraton opton Descrpton Ambent lght control Ambent lght control can be enabled or dsabled. Desred value Value used by the lght sensor to regulate the control gear. On account of the room condtons and the nstallaton heght, the llumnance n the workspace may, however, be three to four tmes hgher. Value range: lx Control speed Speed at whch the control gear reaches the desred value. Value range: ncrements 0 7, wth 0 beng the slowest and 7 the fastest. 254

255 Swtch-on level Level when the lghtng s swtched on. Ambent lght control starts from ths value. Mnmum level Maxmum level calculated: the swtch-on level for ambent lght control s specally calculated so that t s as close to the desred value as possble. Enable dmmng off (brght out) Checkbox enabled: f the measured llumnance exceeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swtched off by the lght sensor even f moton s detected n the room. As soon as the measured llumnance falls below the desred value, the lumnare group s swtched on agan. Threshold Value above whch the lumnare group s swtched off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whch the threshold must be exceeded n order for the lumnare group to be swtched off by the lght sensor. Value range: mn Table 124: Lght sensor confguraton optons n drect master mode 255

256 Settng the response of the DALI MSensor 02 to a scene recall In the detal vew of the DALI MSensor 02 ts response to a scene recall can be set. A response can be confgured for each of the 16 scenes. The followng confguraton optons are avalable: Confguraton Lght sensor Moton sensor automatc The lumnare group assgned to the lght sensor swtches to the presence value. Ambent lght control s enabled. Moton sensor dsabled: the moton sensor s enabled. The run-on tme starts over. Moton sensor enabled: the run-on tme starts over. statc The lumnare group assgned to the lght sensor swtches to the ntensty set n the control gear for the scene n queston. If ambent lght control was enabled before the scene was recalled, t s temporarly dsabled. Moton sensor dsabled: the moton sensor s enabled. The run-on tme starts over. Moton sensor enabled: the run-on tme starts over. off The lumnare group assgned to the lght sensor s swtched off. The moton sensor swtches to status Dead tme (manual off) n progress. MASK The lght sensor gnores the scene recall. The moton sensor gnores the scene recall. Table 125: Response of the DALI MSensor 02 to a scene recall If the response to a scene recall s set to automatc, off or MASK, the MASK value for ths scene must be set for all control gear elements. Informaton on how scenes are confgured can be found n Secton DALI control gear > Confguraton va the detal vew 36. Advanced settngs n drect master mode The followng advanced settngs are dsplayed for the lght sensor n drect master mode f ambent lght control has been enabled. Advanced settngs The "Maxmum level" command starts ambent lght control. Descrpton Checkbox dsabled: after the Maxmum level command s receved, the lumnare group swtches to the maxmum level untl the run-on tme for the moton sensor has expred. If ambent lght control was enabled before the Maxmum level command was receved, t s temporarly 256

257 dsabled. Checkbox enabled: after the Maxmum level command s receved, the lumnare group swtches to the maxmum level. Ambent lght control s started. The "Brghten" and "Dm" commands temporarly change the desred value for ambent lght control. Checkbox dsabled: after a Brghten or Dm command s receved, the lumnare group s smoothly adjusted accordngly. The desred value for ambent lght control remans unchanged. Checkbox enabled: after a Brghten or Dm command s receved, the lumnare group s smoothly adjusted accordngly. The measured llumnance on the DALI MSensor after smooth adjustment s temporarly saved as a new desred value for ambent lght control. The desred value s reset once the run-on tme has expred or an OFF command s receved. Table 126: Lght sensor advanced settngs n drect master mode To apply the changed values to the lght sensor, clck on save. The saved confguraton can now be tested drectly n the feld. 257

258 Reference devce The lght sensor requres a reference devce n order to exactly calculate the swtch-on level for ambent lght control. A reference devce s a DALI control gear element located n the same group as the DALI MSensor. The masterconfigurator automatcally adds the frst DALI control gear element located n the same group as the DALI MSensor as a reference devce. If another DALI control gear element s desred for use as a reference devce, remove the reference devce and add the desred DALI control gear element agan. Removng a reference devce Requrement: Advanced settngs enabled. Clck Remove n the detal vew of the lght sensor. The reference devce s removed. Addng a reference devce Requrement: DALI MSensor has been assgned to a DALI group. 1. In the DALI devce tree dagram, clck on the devce to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the devce to the desred group. (Drag & Drop) The devce s removed from the group n whch t was prevously located and s added to the desred group. The address of the DALI control gear element s automatcally dsplayed as the reference devce n the DALI MSensor. If the DALI control gear element used as a reference devce by the DALI MSensor (or the DALI MSensor tself) s deleted from the DALI group, the nformaton for the reference devce n the DALI MSensor s also deleted. For Reference devce the followng appears: none. 258

259 Moton sensor The moton sensor supports two operatng modes: Drect master mode Slave mode: the moton sensor cannot be confgured n ths operatng mode. The moton sensor just responds to commands from the master devce. More nformaton on these operatng modes can be found n Secton DALI MSensor Drect master mode Status n drect master mode The followng status nformaton s dsplayed for the moton sensor n drect master mode: Status Descrpton Moton sensor Indcates the status of the moton sensor: Off Lghtng at presence value Lghtng at presence value, run-on tme n progress 259

260 Lghtng fadng to absence value, fade tme n progress Lghtng at absence value Lghtng at absence value, swtch-off delay n progress Dead tme (manual off) n progress Update status automatcally Indcates whether the moton sensor status s updated automatcally. Table 127: Moton sensor status nformaton n drect master mode Confguraton optons n drect master mode The followng confguraton optons are dsplayed for the moton sensor n drect master mode: Confguraton opton Descrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatcally swtched on and off dependng on whether presence s detected. (factory settng) enabled (only OFF): the moton sensor swtches the lghtng off only. It must be swtched on manually. dsabled: the moton sensor s dsabled. The lghtng must be swtched on and off manually. : The never OFF functon s mplemented as follows: 1. Select the enabled operatng mode. 2. Select swtch-off delay never OFF. Power on behavour Indcates how the moton sensor wll react after falure of the DALI power supply: no acton last state maxmum level off presence value: specally calculated value for ambent lght control. Fade-n tme Tme requred to reach the presence value. Value range: fast s Presence value Value to whch the lumnare group swtches when presence s detected n the room. The presence value control depends on how the lght sensor s confgured. ambent lght-controlled: If ambent lght control s enabled for the lght sensor, the presence value s regulated based on ambent lght levels. fxed: If ambent lght control s dsabled for the lght sensor, a value can be set as a percentage between 0 100%. 260

261 Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. Value range: 30 s 60 mn nfnte: the run-on tme contnues wthout end. Ths means that the lumnares reman at the defned presence value (ambent lght-controlled or fxed). The fade tme does not start. Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 60 mn never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Fade-out tme Tme requred to dm off from the absence value. Value range: fast s Dead tme (manual off) Tme started by manually swtchng off the lghtng va the momentary-acton swtch or the remote control and durng whch the moton sensor s dsabled. If movement s detected n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s detected n the room, the moton sensor s enabled agan. Value range: 0 s 20 mn Table 128: Moton sensor confguraton optons n drect master mode 261

262 Overvew of confguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay 5) Fade-out tme A) Presence value B) Absence value Advanced settngs n drect master mode The followng advanced settngs are dsplayed for the moton sensor n drect master mode: Advanced settngs Descrpton Set response to presence n other groups Ths settng determnes how the moton sensor responds when presence s detected n another group. Four groups n total can be confgured. MASK: the DALI MSensor 02 gnores the presence detected n another group (factory settng). Presence value: the lumnare group assgned to the DALI MSensor 02 swtches to the presence value. Absence value: the lumnare group assgned to the DALI MSensor 02 swtches to the absence value. Excepton: f the lumnares are already at the presence value, they retan ths settng. Table 129: Moton sensor advanced settngs n drect master mode To apply the changed values to the moton sensor, clck on save. The saved confguraton can now be tested drectly n the feld. 262

263 Remote control The remote control supports two operatng modes: Drect master mode Slave mode: the remote control cannot be confgured n ths operatng mode. The remote control has no functon. More nformaton on these operatng modes can be found n Secton DALI MSensor Drect master mode Confguraton optons n drect master mode The followng devce nformaton s dsplayed for the remote control n drect master mode: Confguraton opton Descrpton Confguraton Confguraton of the remote control: Inactve: the keys of the remote control are nactve. Factory settngs: the remote control keys are assgned wth default settngs. The lumnare group s set usng the 263

264 rotary swtch n the battery compartment of the remote control. user-defned: the keys of the remote control can be assgned to selected functons. Table 130: Remote control confguraton optons n drect master mode Parametersng the key assgnment Wth the user-defned confguraton, the key assgnment of the remote control can be parametersed by the user. If key assgnment s customsed, the group assgnment as defned by the rotary swtch n the battery compartment of the remote control s gnored. The commands only apply to the lumnare group set drectly on the rotary swtch on the DALI MSensor 02. Dependng on the key, varous confguraton optons are avalable: On Off On/Off Brghten Dm Scene 0 15 Intensty 1 100% Ambent lght control Reserved: ths opton s reserved for future functonal enhancements and currently has no functon. To apply the changed values to the remote control, clck on save. The saved confguraton can now be tested drectly n the feld. 264

265 Specal notes: DALI MSensor devces verson 2.0 and lower The behavour of the DALI MSensor 02 s to some extent sgnfcantly dfferent from that of prevous versons (V1.5 or lower). Group assgnment of dfferent generatons of DALI MSensor devces DALI MSensor 02 devces and DALI MSensor devces verson 1.5 or lower cannot be assgned to the same group, as these versons work from dfferent group concepts. Replacng a faulty DALI MSensor (V1.5 or lower) A faulty DALI MSensor V1.5 or lower can only be replaced by a DALI MSensor 02 to a lmted extent. Further nformaton can be found n the product manual for the DALI MSensor 02. Resettng the frmware verson of DALI MSensor 02 devces to verson 1.5 If a faulty DALI MSensor 1.5 cannot be replaced, a DALI MSensor 02 can be reset to frmware verson 1.5 usng the masterconfigurator. More nformaton on the frmware update can be found here The frmware of all DALI MSensors connected to the DALI control lne wll be updated. If only one devce needs to be updated, ths devce must be updated on a separate DALI control lne. The devce must be readdressed after the frmware has been updated. 265

266 8.5.2 DALI MSensor (verson 1.5 and 1.7) DALI MSensors are represented n the DALI devce tree dagram by the detal vew. con and are confgured n the The DALI MSensor conssts nternally of three devce classes, whch are lsted ndvdually n the DALI devce tree dagram: Lght sensor: A detaled descrpton of the lght sensor can be found n Secton DALI MSensor (V1.5 and 1.7) > Lght sensor 268. Moton sensor: A detaled descrpton of the moton sensor can be found n Secton DALI MSensor (V1.5 and 1.7) > Moton sensor 271. Remote control: A detaled descrpton of the remote control can be found n Secton DALI MSensor (V1.5 and 1.7) > Remote control 274. Group concept Every DALI MSensor has two groups: Lumnare group: all devces n ths group are controlled by the DALI MSensor. Sensor group: a group va whch the DALI MSensor can be nfluenced. The next hghest group s automatcally assgned as the sensor group. The followng groups are also dsplayed f advanced settngs have been enabled: Lght sensor group: ed group (eg) contanng the lght sensor. Moton sensor group: ed group (eg) contanng the moton sensor. Remote control group: ed group (eg) contanng the remote control. Effectve range The DALI MSensor controls ether all devces (broadcast) or one DALI group: Assgnment va the rotary swtch The effectve range of the DALI MSensor s set usng the rotary swtch on the back of the sensor. All control gear elements n the set effectve range are controlled by the DALI MSensor. The next hghest group s automatcally assgned as the sensor group. 266

267 Assgnment va the masterconfigurator When the DALI MSensor s not assgned to a group n the DALI devce tree dagram, t controls the lumnare group set usng the rotary swtch on the back of the sensor. It must be assgned to a group to control an ndvdual group. 1. In the DALI devce tree dagram, clck on the DALI MSensor. 2. Hold down the left mouse button. 3. Drag the DALI MSensor to the desred lumnare group. The DALI MSensor s removed from the ndvdual (non-grouped) secton of the DALI devce tree dagram and s added to the desred lumnare group. The next hghest group s automatcally assgned as the sensor group. The poston of the rotary swtch on the back of the DALI MSensor s gnored. If the group assgnment n the masterconfigurator s undone, the rotary swtch poston wll be actve agan. 267

268 Lght sensor Status The followng status nformaton s dsplayed for the lght sensor: Status Descrpton Illumnance Illumnance currently measured at the lght sensor. On account of the room condtons and the nstallaton heght, the llumnance n the workspace may, however, be three to four tmes hgher. Update status automatcally Indcates whether the lght sensor status s updated automatcally. Ambent lght control Indcates the status of ambent lght control for the lght sensor. enabled: ambent lght control s enabled. temporarly dsabled: ambent lght control has been temporarly dsabled manually by the user. dsabled: ambent lght control s dsabled. unknown: there s currently no connecton to the lght sensor. Reference devce Indcates the DALI control gear used as a reference for calculatng the swtch-on level durng ambent lght control. 268

269 If no reference devce has been assgned to the lght sensor, no devce wll be dsplayed. : Secton Reference devce reference devce s assgned. 270 explans how a Table 131: Lght sensor status nformaton Confguraton optons The followng confguraton optons are dsplayed for the lght sensor: Confguraton opton Descrpton Ambent lght control Ambent lght control can be enabled or dsabled. Desred value Value used by the lght sensor to regulate the control gear. On account of the room condtons and the nstallaton heght, the llumnance n the workspace may, however, be three to four tmes hgher. Value range: lx Control speed Speed at whch the control gear reaches the desred value. Value range: ncrements 0 7, wth 0 beng the slowest and 7 the fastest. Swtch-on level Level when the lghtng s swtched on. Ambent lght control starts from ths value. Mnmum level Maxmum level calculated: the swtch-on level for ambent lght control s specally calculated so that t s as close to the desred value as possble. Enable dmmng off (brght out) Checkbox enabled: f the measured llumnance exceeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swtched off by the lght sensor even f moton s detected n the room. As soon as the measured llumnance falls below the desred value, the lumnare group s swtched on agan. Threshold Value above whch the lumnare group s swtched off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whch the threshold must be exceeded n order for the lumnare group to be swtched off by the lght sensor. Value range: mn Table 132: Lght sensor confguraton optons 269

270 To apply the changed values to the lght sensor, clck on save. The saved confguraton can now be tested drectly n the feld. Reference devce The lght sensor requres a reference devce n order to exactly calculate the swtch-on level for ambent lght control. A reference devce s a DALI control gear element located n the same group as the DALI MSensor. The masterconfigurator automatcally adds the frst DALI control gear element located n the same group as the DALI MSensor as a reference devce. If another DALI control gear element s desred for use as a reference devce, remove the reference devce and add the desred DALI control gear element agan. Removng a reference devce Requrement: Advanced settngs enabled. Clck Remove n the detal vew of the lght sensor. The reference devce s removed. Addng a reference devce Requrement: DALI MSensor has been assgned to a DALI group. 1. In the DALI devce tree dagram, clck on the devce to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the devce to the desred group. (Drag & Drop) The devce s removed from the group n whch t was prevously located and s added to the desred group. The address of the DALI control gear element s automatcally dsplayed as the reference devce n the DALI MSensor. If the DALI control gear element used as a reference devce by the DALI MSensor (or the DALI MSensor tself) s deleted from the DALI group, the nformaton for the reference devce n the DALI MSensor s also deleted. For Reference devce the followng appears: none. 270

271 Moton sensor Status The followng status nformaton s dsplayed for the moton sensor: Status Descrpton Moton sensor Indcates the status of the moton sensor: Off Lghtng at presence value Lghtng at presence value, run-on tme n progress Lghtng fadng to absence value, fade tme n progress Lghtng at absence value Lghtng at absence value, swtch-off delay n progress Dead tme (manual off) n progress Update status automatcally Indcates whether the moton sensor status s updated automatcally. Table 133: Moton sensor status nformaton 271

272 Confguraton optons The followng confguraton optons are dsplayed for the moton sensor: Confguraton opton Descrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatcally swtched on and off dependng on whether presence s detected. (factory settng) enabled (only OFF): the moton sensor swtches the lghtng off only. It must be swtched on manually. dsabled: the moton sensor s dsabled. The lghtng must be swtched on and off manually. : The never OFF functon s mplemented as follows: 1. Select the enabled operatng mode. 2. Select swtch-off delay never OFF. Power on behavour Indcates how the moton sensor wll react after falure of the DALI power supply: no acton last state maxmum level off presence value: specally calculated value for ambent lght control. Fade-n tme Tme requred to reach the presence value. Value range: fast s Presence value Value to whch the lumnare group swtches when presence s detected n the room. The presence value control depends on how the lght sensor s confgured. ambent lght-controlled: If ambent lght control s enabled for the lght sensor, the presence value s regulated based on ambent lght levels. fxed: If ambent lght control s dsabled for the lght sensor, a value can be set as a percentage between 0 100%. Run-on tme A tme startng from the last detected movement n the room; when the run-on tme expres, the fade tme begns. If further movement s detected durng the run-on tme, t starts over agan. Value range: 30 s 60 mn nfnte: the run-on tme contnues wthout end. Ths means that the lumnares reman at the defned presence value (ambent lght-controlled or fxed). The fade tme does not start. 272

273 Fade tme Tme durng whch the lghtng s smoothly adjusted to the absence value. Value range: fast s Swtch-off delay Tme for whch the absence value s mantaned f no movement s detected. Value range: 0 s 60 mn never OFF: the lghtng remans at the absence value untl further movement s detected and the moton sensor swtches to the presence value. The lumnare group s never swtched off by the moton sensor. Absence value Level to whch the lumnare group swtches durng the swtch-off delay. Fade-out tme Tme requred to dm off from the absence value. Value range: fast s Dead tme (manual off) Tme started by manually swtchng off the lghtng va the momentary-acton swtch or the remote control and durng whch the moton sensor s dsabled. If movement s detected n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s detected n the room, the moton sensor s enabled agan. Value range: 0 s 20 mn Table 134: Moton sensor confguraton optons Overvew of confguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swtch-off delay 5) Fade-out tme A) Presence value B) Absence value 273

274 To apply the changed values to the moton sensor, clck on save. The saved confguraton can now be tested drectly n the feld Remote control Confguraton optons The followng devce nformaton s dsplayed for the remote control: Confguraton opton Descrpton Confguraton Confguraton of the remote control: Inactve: the keys of the remote control are nactve. Factory settngs: the remote control keys are assgned wth default settngs. The lumnare group s set usng the rotary swtch n the battery compartment of the remote control. user-defned: the keys of the remote control can be assgned to selected functons. Table 135: Remote control confguraton optons 274

275 Parametersng the key assgnment Wth the user-defned confguraton, the key assgnment of the remote control can be parametersed by the user. If key assgnment s customsed, the group assgnment as defned by the rotary swtch n the battery compartment of the remote control s gnored. The commands only apply to the lumnare group set drectly on the rotary swtch on the DALI MSensor. Dependng on the key, varous confguraton optons are avalable: On Off On/Off Brghten Dm Scene 0 15 Intensty 1 100% Ambent lght control Reserved: ths opton s reserved for future functonal enhancements and currently has no functon. To apply the changed values to the remote control, clck on save. The saved confguraton can now be tested drectly n the feld. 275

276 8.5.3 DALI MSensor (verson 1.3) For DALI MSensors wth frmware verson 1.3, there are a few small dfferences compared to DALI MSensors wth verson 1.4 or hgher. Ambent lght control: enabled/dsabled Ths parameter s not supported by a DALI MSensor wth a frmware verson lower than 1.4. In the masterconfigurator software, the parameter appears greyed out. Ambent lght control can be dsabled as follows: 1. Open the detal vew for the moton sensor. 2. Under "Presence value" select the fxed rado button. 3. Enter the percentage for the presence value. 4. Clck on save. Ambent lght control s dsabled. Status There are only two status messages: enabled: ambent lght control s enabled. temporarly dsabled: ambent lght control s dsabled usng the DALI RC remote control or s dsabled temporarly by the user manually. Dead tme (manual off) The lowest value whch can be set for the dead tme s 30 seconds. 276

277 8.6 DALI TOUCHPANEL The DALI TOUCHPANEL s represented n the DALI devce tree dagram by the con and the name DALI Touch. When addressng, the DALI TOUCHPANEL s gven an ed address (ea) and can be confgured n the detal vew usng ths address. Devce nformaton The followng devce nformaton s dsplayed n the header: Devce nformaton Descrpton Name Dsplays the name of the devce. Frmware verson Dsplays the frmware verson of the devce. Table 136: Devce nformaton Confguraton The followng confguraton optons are avalable for the DALI TOUCHPANEL: User-defned: For a detaled descrpton of the user-defned confguraton, see Secton User-defned confguraton 278. Tunable Whte: For a detaled descrpton of the Tunable Whte confguraton, see Secton Tunable Whte 282. Factory settngs: For a detaled descrpton of the Factory settngs, see Secton Factory settngs

278 8.6.1 User-defned confguraton The user-defned confguraton can be enabled usng the masterconfigurator. The 6 keys on the DALI TOUCHPANEL can be confgured ndvdually. Settng the user-defned confguraton 1. Enable the user-defned rado button. A message appears, promptng for confrmaton that the devce confguraton should be modfed. Ths overwrtes the exstng settngs. 2. Confrm the acton by clckng on Yes. 3. Select Key 1. Current confguraton of Key 1 s loaded. The followng confguratons are performed for the selected key. 4. From the Target dropdown lst, select the destnaton address to whch the command s to apply: All, group (0 15) or address (0 63). 5. Select a response from the Set response to key press dropdown lst. For a precse descrpton of possble responses see Response to key press 280 table. 278

279 6. In order to store a DALI command for command X and command Y, enable the DALI command (ndrect) rado button. -orin order to store an ntensty for command X and command Y, enable the Intensty (DAP) rado button. Command X and command Y represent varables that must be stored for the commands. You can ether store DALI commands or an ntensty. 7. Confgure command X and command Y. DALI command (ndrect) Intensty (DAP) Select a DALI command n the dropdown lst. Enter the value for the ntensty. For a precse descrpton of the DALI commands, see Secton DALI commands In order to nvoke command X wth a fade tme, n the command X group feld, enable the Fade Tme checkbox and select a fade tme n the dropdown lst. 9. In order to nvoke command Y wth a fade tme, n the command Y group feld, enable the Fade Tme checkbox and select a fade tme n the dropdown lst. 10.Clck on Save. The confguraton s saved n the DALI TOUCHPANEL. 11.Repeat steps 3 to 10 for keys

280 The saved confguraton can now be tested drectly n the feld. Response to key press bref = toggle between command X and command Y, long = s gnored Descrpton When the key s pressed brefly, command X and command Y are output alternately. A long key press has no effect. Adjustable parameters: Command X Command Y bref = s gnored, long = brghten A bref key press has no effect. In the case of a long key press the command that s output depends on the status of the lghtng: If the lghtng was prevously swtched off, the mnmum level s sent. If the lghtng was prevously swtched on, the lghtng s brghtened. bref = command X, long = brghten Command X and command Y do not have to be defned. Brefly pressng the key outputs the selected command X. In the case of a long key press the command that s output depends on the status of the lghtng: If the lghtng was prevously swtched off, the mnmum level s sent. If the lghtng was prevously swtched on, the lghtng s brghtened. Adjustable parameters: Command X bref = s gnored, long = dm A bref key press has no effect. In the case of a long key press the lghtng s dmmed. bref = command Y, long = dm Command X and command Y do not have to be defned. Brefly pressng the key outputs the selected command Y. In the case of a long key press the lghtng s dmmed. Adjustable parameters: Command Y 280

281 bref = s gnored, long = toggle between brghten and dm A bref key press has no effect. In the case of a long key press the lghtng s brghtened and dmmed alternately. bref = toggle between command X and command Y, long = toggle between brghten and dm Command X and command Y do not have to be defned. When the key s pressed brefly, command X and command Y are output alternately. In the case of a long key press the lghtng s brghtened and dmmed alternately. Adjustable parameters: Command X Command Y Table 137: Summary of response to key press n case of DALI TOUCHPANEL 281

282 8.6.2 Tunable Whte The Tunable Whte confguraton can be enabled usng the masterconfigurator. "Tunable Whte" descrbes the opton to dynamcally change the lght of an LED lumnare n the whte lght range. The colour temperature of Tunable Whte lumnares can be changed n the whte lght range from 2700 to 6500 kelvn. Default settngs for ntensty and colour temperature are assgned to the keys of the DALI TOUCHPANEL. The masterconfigurator software can be used to set the destnaton address and two fade tmes, one for swtchng the lumnares on and one for swtchng them off. As soon as a fade tme has been set for swtchng the lumnares on or off, a fade tme of 1 s s automatcally stored for dmmng. Settng the "Tunable Whte" confguraton Requrement: Tunable Whte lumnares are n use. 1. Enable the Tunable Whte rado button. A message appears, promptng for confrmaton that the devce confguraton should be modfed. Ths overwrtes the exstng settngs. 2. Confrm the acton by clckng on Yes. 3. From the Target dropdown lst, select the destnaton address that the DALI TOUCHPANEL s to control: All, group (0 15) or address (0 63). 282

283 4. In order to store a fade tme for swtchng on, n the command X group feld, enable the Fade Tme checkbox and select a fade tme n the dropdown lst. 5. In order to store a fade tme for swtchng off, n the command Y group feld, enable the Fade Tme checkbox and select a fade tme n the dropdown lst. 6. Clck on Save. The confguraton s saved n the DALI TOUCHPANEL. The saved confguraton can now be tested drectly n the feld. 283

284 8.6.3 Factory settngs The keys of the DALI TOUCHPANEL are assgned as follows by default. Key 1: Go to scene 1 Key 2: Up Key 3: Go to scene 2 Key 4: Down Key 5: Go to scene 3 Key 6: Off When the factory settngs are stored n the DALI TOUCHPANEL, a dagram showng the key assgnments s dsplayed n the masterconfigurator. The factory settngs cannot be modfed. In order to set the DALI TOUCHPANEL up as user defned, enable the user-defned confguraton. For a detaled descrpton of the user-defned confguraton, see Secton Userdefned confguraton 278. Restorng the factory settngs 1. Clck on Factory settngs. A message appears, promptng for confrmaton that the devce should be reset to ts factory settngs. 2. Confrm the acton by clckng on Yes. The devce s reset to ts factory settngs. 284

285 8.7 DALI PS2 Standby The DALI PS2 Standby s a DALI power supply wth 240 ma nomnal current for DALI control gear and DALI control unts whch do not have ther own power supply. To reduce the standby losses, the bult-n relay dsconnects the control gear from the mans as soon as all the lumnares have been swtched off. Ths ensures that the power loss s reduced to a mnmum. The DALI PS2 Standby s represented n the DALI devce tree dagram by the the detal vew. con and s confgured n Confguraton opton Descrpton Standby/Actve Indcates the status of the DALI PS2 Standby: Standby Actve swtch to: Standby swtch to: Actve Ths button allows the user to swtch between the Actve and Standby modes. Update status automatcally The status s updated automatcally. Swtch-off delay Tme that starts runnng as soon as t s detected that all the 285

286 DALI control gear has been swtched off, after whch the unt swtches to standby mode. Value range: 1 mn 2 d Standby mode dsabled The DALI PS2 Standby behaves lke a conventonal DALI power supply nstead of swtchng to standby mode. Lght level poll nterval Tme nterval n whch the control gear s polled about the lght level. Value range: 1 mn 23 h Ballast power up delay Tme durng whch the frst 10 commands that are sent whle the electronc ballasts are powerng up wll be buffered. At the end of the electronc ballast swtch-on delay, the commands are sent from the power supply to the electronc ballasts. Ths ensures that no commands are lost whle the electronc ballasts are startng up. Command buffer Number of commands that are buffered whle the electronc ballasts are startng up. Value range: 1 10 commands Relay state nverted dsabled: f all the devces are swtched off, the relay output s open. (factory settng) enabled: f all the devces are swtched off, the relay output s closed. DALI LED nverted enabled: LED llumnates only f there s communcaton on the DALI control lne. (factory settng) dsabled: LED llumnates when the power supply s ready for operaton. If there s communcaton on the DALI control lne, the LED wll go out brefly. Standby LED nverted dsabled: LED llumnates when standby mode s enabled. (factory settng) enabled: LED llumnates when standby mode s dsabled. Update/read current values If the checkbox s selected, the current values of the voltage (V) and of the flowng supply current (ma) are dsplayed. Table 138: Confguraton optons for DALI PS2 Standby n the detal vew To apply the changed values to the DALI PS 2 Standby, clck on Save. The saved confguraton can now be tested drectly n the feld. 286

287 8.8 DALI-Somfy anmeo Interface The DALI Somfy anmeo nterface s represented n the DALI devce tree dagram by the confgured n the detal vew. con and s The DALI Somfy anmeo nterface s an nterface module wth four addresses. Wth each of these addresses t s possble to control one of the four motors of the anmeo IB+ motor controller. Each address of the DALI Somfy anmeo nterface appears ndvdually n the devce tree dagram. Confguraton opton Descrpton Actual poston of blnd Indcates the actual poston (0 100%) and the actual angle (0 200%) of the blnd. Ergonomcs Determnes the behavour of the blnd durng tltng, when one of the followng commands s sent: Off, Down, Recall mn US: moves to the lower end poston EU: makes a small postve angle movement Up, On and step up, Recall max US: moves to the upper end poston EU: makes a small negatve angle movement Scene assgnment Confgure scenes Value range: 287

288 Poston: 0 100% Tlt: 0 200% MASK: the blnds n ths group retan ther current poston when the respectve scene s called up. Table 139: Confguraton optons for the DALI Somfy anmeo nterface n the detal vew Before scenes can be set or recalled for the blnds, the runnng and tltng tmes must be set n the Somfy anmeo motor controller. To apply the new values to the DALI Somfy anmeo nterface, clck on Save. The saved confguraton can now be tested drectly n the feld. 288

289 8.9 Quck test The confguraton of the ndvdual control gear elements can be tested n the Quck test pop-up wndow. Intensty Scenes DALI commands xy-coordnates Colour temperature 292 Sendng current ntensty 1. Set the value usng the slder. The desred value s dsplayed as a DALI value n the tool tp wndow. 2. Clck Send. The value wll be sent to the control gear and recalled wth the set fade tme. The current ntensty s dsplayed to the left of the slder. The selected value must be between the Mnmum level and the Maxmum level. 289

290 Recallng scene X Clck Scene X (0 15). Scene X (0 15) s recalled. The defned fade tme wll be used. Sendng a command The followng DALI commands can be tested: DALI command Descrpton Mnmum level The mnmum level s recalled mmedately wthout any fade tme. Maxmum level The maxmum level s recalled mmedately wthout any fade tme. Dm The ntensty s reduced by the steps defned n the fade rate. When the lghtng reaches the set mnmum level, t remans at ths level. : As long as the Dm button s pressed, the Dm command wll be sent repeatedly. Brghten The ntensty s ncreased by the steps defned n the fade rate. When the lghtng reaches the set maxmum level, t remans at ths level. : As long as the Brghten button s pressed, the Brghten command wll be sent repeatedly. Step darker The ntensty s reduced by one step. Step brghter The ntensty s ncreased by one step. Step darker - Off If the lghtng s swtched on, the ntensty s reduced by one step. If the lghtng reaches the mnmum level, t s swtched off. Mn. level + step brghter If the lghtng s swtched off, the mnmum level s recalled. If the lghtng s swtched on, the ntensty s ncreased by one step. Off The lghtng s swtched off mmedately wthout any fade tme. Table 140: DALI commands The DALI commands Step darker, Step brghter, Step darker - Off and Mn. level + step brghter are only vsble when the advanced settngs are enabled. Informaton on how to enable the advanced settngs can be found n Secton Actve wndow

291 Sendng xy-coordnates 1. Set the value usng the slder. -orclck the button for a pre-defned colour temperature, e.g. Cheese. 2. Clck Send. The value wll be sent to the control gear and recalled wth the set fade tme. 291

292 Sendng the colour temperature 1. Set the value usng the slder. -orclck the button for a pre-defned colour temperature, e.g K. 2. Clck Send. The value wll be sent to the control gear and recalled wth the set fade tme. 292

293 9 Tools The masterconfigurator software provdes the followng tools: Command admnstrator Control gear wzard Frmware update Command admnstrator The Command admnstrator enables the advanced DALI user to send DALI and DSI commands drectly to all control gear connected to the control lne, to an ndvdual group or an ndvdual address, and also to work wth command sequences DALI commands Ths functon of the command admnstrator allows the user to send DALI commands to all control gear connected to the control lne, to an ndvdual group or to an ndvdual address. Sendng a DALI command Requrement: Knowledge of the DALI command set. 1. Select Tools > Command admnstrator. The Command admnstrator pop-up wndow appears. 2. Clck on the DALI commands tab. 3. Select rado button all, group or address. 4. Enter the number of the command. -orselect the desred command from the drop-down lst. 5. Enter the value n decmal (dec) or hexadecmal (hex). -orset the value usng the slder. 6. In order to repeat the command once, select the checkbox Repeat command once. 293

294 7. In order to repeat the command every 500 ms, select the checkbox Repeat command every 500 ms. 8. Clck on Send command. The DALI command wll be sent n accordance wth the selected optons. The response appears mmedately n the Response feld DSI commands Ths functon of the Command admnstrator allows the user to send DSI commands to all control gear connected to the control lne. To do so, frst send a value and then the desred command. Sendng a value Requrement: Knowledge of the DSI command set. 1. Select Tools > Command admnstrator. The Command admnstrator pop-up wndow appears. 2. Clck on the DSI commands tab. 3. Enter the ntensty n decmal (dec) or hexadecmal (hex). -orset the ntensty usng the slder. 4. Clck on Send value. The value wll be sent to all control gear connected to the control lne. 294

295 Sendng a command Requrements: Knowledge of the DSI command set. Command admnstrator pop-up wndow and DSI commands tab open. 1. Select the desred command from the Command drop-down lst. 2. In order to repeat the command every 500 ms, select the checkbox Repeat command every 500 ms. 3. Clck on Send command. The DSI command wll be sent to all control gear connected to the control lne Command sequence Ths functon of the Command admnstrator allows the user to send a sequence of DALI or DSI commands. Create command sequence Requrement: Knowledge of the DALI and DSI command sets. 1. Select Tools > Command admnstrator. The Command admnstrator pop-up wndow appears. 2. Clck on the Command sequence tab. 295

296 3. Clck on Add command. The Add command pop-up wndow appears. 4. Defne the DALI or DSI command va the nput felds, lsts and rado buttons. 5. Optonally, a delay tme n mllseconds can be defned. 6. Clck on Add. The DALI or DSI command s added to the command sequence. Further functons Descrpton Open Open a prevously saved command sequence. Save Save the current command sequence n a fle wth the extenson *.cot. Add command Add a new command to the command sequence. Change command Change the selected command. Delete command Delete the selected command. Delete sequence Delete all commands. Sngle step One command at a tme s sent to the devces or groups n the specfed order. Start Start the command sequence. All commands are sent to the defned destnaton address (all, group, ndvdual address) n the specfed order. Stop Stop the command sequence. Infnte loop Repeat the command sequence endlessly. Table 141: Command admnstrator - further functons 296

297 9.2 Control gear wzard The control gear wzard can be used to enable and confgure control gear functons and parameters. The confguratons are sent to all control gear connected to the DALI control lne. Functons and parameters Descrpton Interface mode Select an nterface operatng mode. corrdorfunction Carry out corrdor control wth a smple moton sensor. Devce confguraton Set the epoweron level and dmmng/swtchng parameters n DC mode. DC level Set the ntensty to whch the ballast should dm/brghten n DC mode. Compatblty settngs Parameterse the ballast so that ts settngs match those of the precedng generaton of devces. Ths functon s desgned for replacng ballasts n exstng systems. Commssonng date Store the date the system was commssoned n the control gear. The date can only be set once. Reset default settngs Delete all prevous settngs and reset to the defaults. Table 142: Control gear w zard functons Adjustng the settngs requres extensve knowledge of the control gear. For further detals on the ndvdual functons of the control gear wzard, please refer to the relevant devce documentaton. 9.3 Localsaton wzard for DALI XC The localsaton wzard for DALI XC can be used for tactle locaton of the ndvdual nputs of the DALI XC wth a double-clck. The localsaton wzard creates a lst of located devces. Ths lst can be used to note the assocated address and nput (T1 T4) n the addressng plan for each momentary-acton swtch or standard swtch connected to a DALI XC. 297

298 Locatng momentary-acton swtches or standard swtches usng the localsaton wzard 1. Select menu tem Tools > Localsaton wzard for DALI XC... The Localsaton wzard for DALI XC pop-up wndow appears. 2. Double-clck one of the momentary-acton swtches or standard swtches connected to a DALI XC. Consecutve numbers and ed addresses for the assocated DALI XC and the nput (T1 T4) of the momentary-acton swtch or standard swtch pressed are added to the lst. 3. Repeat step 2 for each of the momentary-acton swtches or standard swtches connected to a DALI XC. 4. the ed addresses and nputs n the addressng plan. To be able to contnue to use the nformaton n a text edtng program, select the content of ths pop-up wndow usng the mouse and then press CTRL + C to copy. 5. To delete the lst, clck Delete lst. Lst s deleted. 6. To ext the localsaton wzard, clck Ext. Localsaton wzard s closed. Lst s deleted. 298

299 Confgurng located momentary-acton swtches or standard swtches The localsaton wzard for DALI XC always opens n a separate pop-up wndow. Ths wndow remans open untl you ext the localsaton wzard. The wzard provdes the opton of confgurng a located momentaryacton swtch or standard swtch drectly. Requrements: Momentary-acton swtch or standard swtch has been located n the localsaton wzard for DALI XC. Localsaton wzard for DALI XC s stopped but not closed. 1. To confgure nput T3 of the DALI XC wth ed address 44, for example, clck the DALI XC wth ed address 44 n the DALI devce tree dagram. The basc confguraton s opened n the detal vew. 2. Clck on the T3 tab. The T3 tab s opened n the detal vew. The localsaton wzard remans open n a separate pop-up wndow. 3. Confgure nput T3. 4. Clck on Save. For a detaled descrpton of the confguraton optons, see Secton DALI XC

300 9.4 Frmware update The frmware of the followng devces can be updated usng the masterconfigurator software: DALI MSensor Frmware verson 1.5 or hgher cannot be used for DALI MSensors wth versons 1.3 or 1.4, as these nvolve dfferent hardware. DALI Somfy anmeo nterface DALI TOUCHPANEL The frmware update wll take around 20 mnutes. Durng the update, the power supply and connecton to the DALI control lne must not be nterrupted. Update frmware The frmware of all DALI MSensors, DALI Somfy anmeo nterfaces or DALI TOUCHPANELS connected to the DALI control lne wll be updated. If only one devce needs to be updated, ths devce must be updated on a separate DALI control lne. The devce must be readdressed after the frmware has been updated. 1. In the menu bar, clck on Tools > Update frmware. The Update frmware pop-up wndow appears. 2. Clck on Open. 3. Select *.hex fle. The fle name for DALI MSensors follows ths format: dalms150.hex, where the number ndcates the verson of the frmware. The fle name for DALI Somfy anmeo nterfaces follows ths format: SomfyMoCo_V19.hex. 4. To update the frmware of all the DALI MSensors connected to the DALI control lne, enable the MSensor rado button. -orto update the frmware of all the DALI Somfy anmeo nterfaces connected to the DALI control lne, 300

301 enable the SomfyMoCo nterface rado button. -orto update the frmware of all the DALI TOUCHPANELS connected to the DALI control lne, enable the DALI TOUCHPANEL rado button. 5. Clck on Start. A message appears whch states that the update wll take mnutes. 6. Confrm the message by clckng on Yes. The frmware of all DALI MSensors, DALI Somfy anmeo nterfaces or DALI TOUCHPANELS connected to the DALI control lne wll be updated. The Frmware update completed pop-up wndow appears. Ths completes the update. The updated devces must be re-addressed. More nformaton on system extenson wth unaddressed devces can be found n Secton Addressng

302 10 Further components The programs DALI Montor V and DALI BusServer V are also nstalled wth the masterconfigurator software; these programs support the user when workng wth the masterconfigurator software DALI Montor The DALI Montor allows the user to montor the DALI control lne. The DALI Montor records the commands on the DALI control lne, enablng the user to check that the commands are sent correctly. Openng the DALI Montor Clck on Start > Programs > DALITools > DALIMontor. 302

303 10.2 DALI BusServer The DALI BusServer manages the nterface to the DALI control lne. The DALI BusServer allows multple Wndows applcatons to access the nterface at the same tme. Ths means the masterconfigurator software can be used to send commands whlst the DALI Montor can be used smultaneously to check whether the commands were sent correctly. The confgtool operates wth the DALI BusServer V It s therefore not possble to have the confgtool and the masterconfigurator software open at the same tme. The DALI BusServer opens automatcally when the masterconfigurator software or the DALI Montor s started. As soon as the DALI BusServer s runnng, t can be accessed va the con n the Wndows task bar. 303