SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
|
|
- Camilla Merry Parrish
- 5 years ago
- Views:
Transcription
1 GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power supply. It features high-bandwidth (300MHz) and low on-resistance (4Ω TYP), targeted applications for audio switching. The SGM44601 is configured as a dual double-pole /double-throw (DPDT) device with two logic control inputs that control two multiplexer/demultiplexers each. The configuration can also be used as a dual differential 2-to-1 multiplexer/ demultiplexer. FEATURES Low Voltage Operation: 1.8V to 5.5V Low On-Resistance: 4Ω (TYP) Low On-Resistance Flatness -3dB Bandwidth: 300MHz Rail-to-Rail Input and Output Operation High Off-Isolation: -75dB at 1MHz Low Crosstalk: -100dB at 1MHz Typical Power Consumption (< 0.01μW) TTL/CMOS Compatible Available in Green TQFN L Package Extended Industrial Temperature Range: -40 to +85 SGM44601 is available in Green TQFN L package. BLOCK DIAGRAM APPLICATIONS Communication Systems Cell Phones Portable Instrumentation Audio Signal Routing Audio and Video Switching PCMCIA Cards Computer Peripherals Modems PDAs 1 IN1-IN2 2 3 IN3-IN4 4 NC1 NO1 NC2 NO2 NC3 NO3 NC4 NO4 REV. A. 4
2 PACKAGE/ORDERING INFORMATION MODEL PIN- PACKAGE SPECIFIED TEMPERATURE RANGE ORDERING NUMBER PACKAGE MARKING PACKAGE OPTION SGM44601 TQFN L -40 to +85 SGM44601YTQA16/TR Tape and Reel, 3000 ABSOLUTE MAXIMUM RATINGS to...0v to 6V Analog, Digital voltage range V to () +0.3V Continuous Current NO, NC, or...±100ma Operating Temperature Range to +85 Junction Temperature Storage Temperature Range to +150 Lead Temperature (soldering, 10s) NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. CAUTION This integrated circuit can be damaged by ESD if you don t pay attention to ESD protection. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. SGMICRO reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. Please contact SGMICRO sales office to get the latest datasheet. 2
3 PIN CONFIGURATION (TOP VIEW) SGM44601YTQA16 4 NO4 IN3-IN4 NC3 NC NO3 NO NC2 NC1 IN1-IN2 NO2 2 TQFN L PIN DESCRIPTION NAME TQFN PIN FUNCTION 14 Power Supply. 6 Ground. IN X 2, 10 Digital Control Pin to Connect the Terminal to the NO or NC Terminals. X 16, 4, 8, 12 Common Terminal. NO X 15, 3, 7, 11 Normally-Open Terminal. NC X 1, 5, 9, 13 Normally-Closed Terminal. NOTE: NO X, NC X and X terminals may be an input or output. FUNCTION TABLE FUNCTION IN1-IN2 NC1 and NC2 NO1 and NO2 0 ON OFF 1 OFF ON FUNCTION IN3-IN4 NC3 and NC4 NO3 and NO4 0 ON OFF 1 OFF ON 3
4 ELECTRICAL CHARACTERISTICS ( = +4.5V to +5.5V, = 0V, V IH = +1.6V, V IL = +0.5V, T A = -40 to +85. Typical values are at = +5.0V, T A = +25, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS TEMP MIN TYP MAX UNITS ANALOG SWITCH Analog Signal Range V NO, V NC, V -40 to V On-Resistance On-Resistance Match Between Channels On-Resistance Flatness Source OFF Leakage Current Channel ON Leakage Current DIGITAL INPUTS R ON R ON R FLAT(ON) I NC(OFF), I NO(OFF) I NC(ON), I NO(ON), I (ON) = 4.5V, 0V V NO or V NC, I = -100mA, Test Circuit 1 = 4.5V, 0V V NO or V NC, I = -100mA, Test Circuit 1 = 4.5V, 0V V NO or V NC, I = -100mA, Test Circuit 1 =5.5V, V NO or V NC = 3.3V/0.3V, V = 0.3V/3.3V = 5.5V, V = 0.3V/3.3V, V NO or V NC = 0.3V/3.3V or floating Ω -40 to Ω Ω -40 to Ω Ω -40 to Ω -40 to μa -40 to μa Input High Voltage V INH -40 to V Input Low Voltage V INL -40 to V Input Leakage Current I IN = 5.5V, V IN = 0V or 5.5V -40 to μa DYNAMIC CHARACTERISTICS Turn-On Time t ON V NC or V NO = 3.0V, R L = 300Ω, ns Turn-Off Time t OFF = 35pF, Test Circuit ns Break-Before-Make Time Delay Charge Injection Off Isolation Channel-to-Channel Crosstalk -3dB Bandwidth Channel ON Capacitance POWER REQUIREMENTS t D Q O ISO X TALK BW C NC(ON), C NO(ON), C (ON) V NC or V NO = 3.0V, R L = 300Ω, = 35pF, Test Circuit4 V G =, R G = 0Ω, = 1.0nF, Q =, Test Circuit3 Signal = 0dBm, R L = 50Ω, Test Circuit5 Signal = 0dBm,R L = 50Ω, Test Circuit6 Signal = 0dBm, R L = 50Ω, Test Circuit ns pc 1MHz MHz MHz MHz db db MHz pf Power Supply Range -40 to V Power Supply Current I + = 5.5V, V IN = 0V or -40 to μa 4
5 ELECTRICAL CHARACTERISTICS ( = +2.7V to +3.6V, V IH = +1.6V, V IL = +0.4V, T A = -40 to +85. Typical values are at = +3.0V, T A = +25, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS TEMP MIN TYP MAX UNITS ANALOG SWITCH Analog Signal Range V NO, V NC, V -40 to V On-Resistance On-Resistance Match Between Channels On-Resistance Flatness Source OFF Leakage Current Channel ON Leakage Current DIGITAL INPUTS R ON R ON R FLAT(ON) I NC(OFF), I NO(OFF) I NC(ON), I NO(ON), I (ON) = 2.7V, 0V V NO or V NC, I = -100mA, Test Circuit 1 = 2.7V, 0V V NO or V NC, I = -100mA, Test Circuit 1 = 2.7V, 0V V NO or V NC, I = -100mA, Test Circuit 1 = 3.6V, V NO or V NC = 3.3V/0.3V, V = 0.3V/3.3V = 3.6V, V = 0.3V/3.3V, V NO or V NC = 0.3V/3.3V or floating Ω -40 to Ω Ω -40 to Ω Ω -40 to Ω -40 to μa -40 to μa Input High Voltage V INH -40 to V Input Low Voltage V INL -40 to V Input Leakage Current I IN = 2.7V, V IN = 0V or2.7v -40 to μa DYNAMIC CHARACTERISTICS Turn-On Time t ON V NC or V NO = 1.5V, R L = 300Ω, ns Turn-Off Time t OFF = 35pF, Test Circuit ns Break-Before-Make Time Delay Charge Injection Off Isolation Channel-to-Channel Crosstalk -3dB Bandwidth Channel ON Capacitance t D Q O ISO X TALK BW C NC(ON), C NO(ON), C (ON) V NC or V NO = 1.5V, R L = 300Ω, = 35pF, Test Circuit4 V G =, R G = 0Ω, = 1.0nF, Q =, Test Circuit3 Signal = 0dBm, R L = 50Ω, Test Circuit5 Signal = 0dBm, R L = 50Ω, Test Circuit6 Signal = 0dBm, R L = 50Ω, Test Circuit ns pc 1MH db 10MHz db 1MHz db 10MHz db MHz pf 5
6 SGM44601 TYPICAL PERFORMANCE CHARACTERISTICS On Response (db) On Response vs. Frequency = +4.2V T A = +25 On Response (db) On Response vs. Frequency = +3V T A = Frequency (MHz) Frequency (MHz) On Response (db) Response vs. Frequency OFF-ISOLATION -80 CROSSTALK -100 = +4.2V -120 T A = Frequency (MHz) On Response (db) OFF-ISOLATION Response vs. Frequency CROSSTALK = +3V T A = Frequency (MHz) 6
7 TEST CIRCUITS 100mA V1 NO or NC V NO or V NC R ON = V1/100mA Test Circuit 1. On Resistance 0.1μF NO or NC V IN 50% 50% V NO or V NC IN RL 300Ω 35pF 90% 90% t ON t OFF Test Circuit 2. Switching Times (t ON, t OFF) 0.1μF R G NO or NC Δ V G IN 1nF V IN ON OFF ON 0V Q = Δ V IN Test Circuit 3. Charge Injection 7
8 TEST CIRCUITS (Cont.) 0.1μF V NO or V NC NC NO V IN 0 50% IN R L 300Ω 35pF V NO or V NC 90% t D Test Circuit 4. Break-Before-Make Time Delay (t D) 0.1µF NC NO Source Signal R L 50Ω IN R L 50Ω 5pF Test Circuit 5. Off Isolation 0.1μF NO or NC Source Signal N.C. NO or NC R L 50Ω 5pF IN1-IN2 R L 50Ω 5pF Channel To Channel Crosstalk = -20 log V NO or V NC Test Circuit 6. Channel-to-Channel Crosstalk 8
9 TEST CIRCUITS (Cont.) 10nF NO or NC Source Signal IN R L 50Ω 5pF Test Circuit 7. -3dB Bandwidth 9
10 PACKAGE INFORMATION PACKAGE OUTLINE DIMENSIONS TQFN L 2.600± ± TYP ( 15) PIN #1 IDENTIFICATION CHAMFER ± Ref ± N16 PIN #1 DOT BY MARKING TOP VIEW N2 N ± BOTTOM VIEW ± SIDE VIEW 0.050± Ref REMENDED LAND PATTERN NOTE: All linear dimensions are in millimeters. TX
11 PACKAGE INFORMATION TAPE AND REEL INFORMATION REEL DIMENSIONS TAPE DIMENSIONS P2 P0 W Q1 Q2 Q1 Q2 Q1 Q2 B0 Q3 Q4 Q3 Q4 Q3 Q4 Reel Diameter P1 A0 K0 Reel Width (W1) DIRECTION OF FEED NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF TAPE AND REEL Package Type Reel Diameter Reel Width W1 A0 B0 K0 P0 P1 P2 W Pin1 Quadrant TQFN L Q1 DD0001 TX
12 PACKAGE INFORMATION CARTON BOX DIMENSIONS NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF CARTON BOX Reel Type Length Width Height Pizza/Carton 7 (Option) DD0002 TX
SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
More informationSGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM44599 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
More informationSGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM4461 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
More informationSGM Ω, Low Voltage Quad, SPDT Analog Switch
GENERAL DESCRIPTION The SGM3699 is a quad, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch that is designed to operate from a single 1.8V to 4.35V power
More informationSGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM4462 is a dual, high-speed, low-voltage, double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single 1.8V to 5.5V power supply. It features high-bandwidth
More informationSGM4684 Chip Scale Packaging, Low-Voltage 0.4Ω, Dual, SPDT Analog Switch
GENERAL DESCRIPTION The SGM4684 is a dual, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch designed to operate from a single 1.8V to 5.5V power supply.
More informationSGM Ω, 300MHz, Low-Power Full-Speed USB (12Mbps) Switch
GENERAL ESCRIPTION The SGM2258 is a high-performance, dual, single-pole/ double-throw (SPT) CMOS analog switch designed for switching USB 1.1 signals. High bandwidth and low on-resistance make this switch
More informationSGM MHz, Low Voltage SPDT Analog Switch in 6-pin SC70
GENERAL DESCRIPTION The SGM3167 is a single, bidirectional, single-pole/ double-throw (SPDT) CMOS analog switches designed to operate from a single 1.8V to 5.5V supply. It features high-bandwidth (600MHz)
More informationSGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch
GENERAL DESCRIPTION The SGM7222 is a high-speed, low-power double-pole/ double-throw (DPDT) analog switch that operates from a single 1.8V to 4.3V power supply. SGM7222 is designed for the switching of
More informationSGM3003 Ultra Low ON-Resistance, Low Voltage, SPDT Analog Switch
GENERAL DESCRIPTION The SGM3003 is a single, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch designed to operate from a single +1.8V to +5.5V supply. Targeted
More informationSGM3717 4Ω, 400MHz Bandwidth, Dual, SPDT Negative Signal Handling Analog Switch
Preliminary datasheet SGM3717 GENERAL DESCRIPTION The SGM3717 is a dual, bidirectional, single-pole/ double-throw (SPDT) CMOS analog switch designed to operate from a single +2.5V to +5.0V supply. It features
More informationSGM Ω Ultra Low ON-Resistance, Dual, SPDT Analog Switch
GENERAL DESCRIPTION The SGM2267 is a dual single-pole/double-throw (SPDT) analog switch that is designed to operate from a single +1.8V to +4.2V power supply. Targeted applications include battery powered
More informationSGM Ω, 300MHz, Low-Power Full-Speed USB (12Mbps) Switch
GENERAL ESCRIPTION The SGM2258 is a high-performance, dual, single-pole/ double-throw (SPT) CMOS analog switch designed for switching USB 1.1 signals. High bandwidth and low on-resistance make this switch
More information4Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power supply.
More informationSGM7228 Low Cost, High Speed USB 2.0 (480Mbps) DPDT Analog Switch
GENERAL DECRIPTION The GM7228 is a high-speed, low-power double-pole/ double-throw (DPDT) analog switch that operates from a single 1.8V to 4.3V power supply. GM7228 is designed for the switching of high-speed
More informationSGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch
GENERAL DECRIPTION The GM7222 is a high-speed, low-power double-pole/ double-throw (DPDT) analog switch that operates from a single 1.8V to 4.3V power supply. GM7222 is designed for the switching of high-speed
More informationSGM48754 Quad SPST CMOS Analog Switch
GENERAL DESCRIPTION The is a CMOS analog switch configured as quad SPST. This CMOS device can operate from 2.5V to 5.5V single supplies. Each switch can handle rail-to-rail analog signals. The off-leakage
More informationSGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch
GENERAL DESCRIPTION The SGM330A is a quad, bidirectional, single-pole/ double-throw (SPDT) CMOS video analog switch (Mux/ DeMux) designed to operate from a single 2.7V to 5.5V power supply. This 2-channel
More informationHigh Speed, Low Voltage, Dual, DPDT Analog Switch
High Speed, Low Voltage, Dual, DPDT Analog Switch General Description UM QFN16 3.0 3.0 UMA QFN16 2.6 1.8 The UM/A is a high speed, dual, dual-pole/double-throw (DPDT) analog switch operates from a single
More informationSGM mW Differential Input, Stereo Audio Power Amplifier
SGM482 2mW Differential Input, GENERAL DESCRIPTION The SGM482 is a stereo audio power amplifier with differential inputs. Operating on a single 5V power supply, it delivers 2mW of continuous RMS power
More informationSGM3798 Audio Headset Analog Switch with Reduced GND Switch R ON and FM Capability
GENERAL DESCRIPTION The is an audio headset analog switch that is used to detect 3.5mm accessories and switch SLEEVE and RING2 by external controller. The ground signal is routed through a pair of low-impedance
More informationHigh Speed, Low Voltage, Dual, DPDT Analog Switch
High Speed, Low Voltage, Dual, DPDT Analog Switch General Description UM QF 3.0 3.0 UMA QF 2.6 1.8 The UM/A is a high speed, dual, dual-pole/double-throw (DPDT) analog switch operates from a single +1.8V
More informationSGM W Audio Power Amplifier
GENERAL DESCRIPTION The SGM489 is a.2w, fully integrated, audio power amplifier. It is designed to maximize audio performance in portable applications such as mobile phone. The portable application requires
More informationSGM8140 Low Power, Vibration Sensor and PIR Sensor Analog Front End (AFE)
SGM814 PRODUCT DESCRIPTION The SGM814 is a PIR sensor and vibration sensor analog front end which consists of 2 independent building block circuits. One is a dual rail-to-rail input and output operational
More informationPI5A121/PI5A122/PI5A124
es Features Single-Supply Operation (+V to +6V) Rail-to-Rail Analog Signal Dynamic Range Low On-Resistance (6Ω typ. with 5V supply) Minimizes Distortion and Error Voltages On-Resistance Flatness, Ω typ.
More informationSGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch
GERAL DESCRIPTION The SGM330A is a quad, bidirectional, single-pole/ double-throw (SPDT) CMOS video analog switch (Mux/DeMux) designed to operate at a single +5V supply. This 2-channel multiplexer/demultiplexer
More informationSGM mW, Capless, Stereo Headphone Amplifier with Shutdown
GENERAL DESCRIPTION The SGM4914 stereo headphone amplifier is designed for portable equipment where board space is at a premium. The SGM4914 uses capless architecture to produce a ground-referenced output
More informationSGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain
SGM9111 8MHz Rail-to-Rail Composite GENERAL DESCRIPTION The SGM9111 is a single rail-to-rail -pole output reconstruction filter with a -3dB bandwidth of 8MHz and 3V/µs slew rate. Operating from single
More informationMP2735/MP2736 Low-Voltage 0.45Ω Dual SPDT Analog Switches
The Future of Analog IC Technology GENERAL DESCRIPTION The MP2735/MP2736 are low voltage, low onresistance, dual single-pole, double-throw (SPDT) monolithic CMOS analog switches designed for high performance
More informationMultiplexers/Switches
EVALUATION KIT AVAILABLE / General Description The / are low-voltage, single-supply CMOS analog switches configured as a 4-channel multiplexer/demultiplexer () and a double-pole/double-throw (DPDT) switch
More informationSGM W Fully Differential Audio Power Amplifier with Selectable Shutdown
GENERAL DESCRIPTION The SGM4996 is a fully differential audio power amplifier that is designed for portable communication device applications and demanding applications in mobile phones. It is capable
More informationSGM4809 Dual 158mW Headphone Amplifier with Active Low Shutdown Mode
Dual 58mW Headphone Amplifier GENERAL DESCRIPTION The SGM4809 is a dual audio power amplifier capable of delivering 58mW per channel of continuous average power with less than 0.% distortion(thd N)when
More informationSGM8925/7 110kHz, 6.4μA, Rail-to-Rail Output CMOS Operational Amplifiers
PRODUCT DESCRIPTION The SGM8925 and SGM8927 are low power, low offset voltage and rail-to-rail output voltage feedback amplifiers. They have a wide output voltage swing, and take the minimum operating
More informationThe UM4684 is a sub 1Ω (0.5Ω at 2.7V) dual SPDT analog switch designed for low voltage
General Description 0.5Ω Low-Voltage Dual SPDT Analog Switch H CSP10 2.0 1.5 EEUE MSOP10 The is a sub 1Ω (0.5Ω at 2.7V) dual SPDT analog switch designed for low voltage applications. The has on-resistance
More informationSON3130 FEATURES PRODUCT DESCRIPTION PIN CONFIGURATION (TOP VIEW) APPLICATIONS
PRODUCT DESCRIPTION The SON313 is designed for heart rate output with SON133(heart rate sensor) offering low cost. It has a wide input common mode voltage range and output voltage swing, and takes the
More informationSGM9203 Triple, 6th-Order, Video Filter Driver for SD/PS/HD (1080i)/HD (1080p)
SGM923 for SD/PS/HD (18i)/HD (18p) PRODUCT DESCRIPTION The SGM923 is a comprehensive filtering solution designed to give designers the flexibility to easily filter and drive various video signals, including
More information0.8Ω, Low-Voltage, 4-Channel Analog Multiplexer
General Description The is a low on-resistance, low-voltage, 4-channel CMOS analog multiplexer that operates from a single 1.6V to 3.6V supply. This device has fast switching speeds (t ON = 25ns, t OFF
More informationSGM8705 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator
SGM87 Micro-Power, CMOS Input, RRIO, 1.4V, GENERAL DESCRIPTION The SGM87 is a dual low power comparator with a typical power supply current of 3nA (per channel). It has the best-in-class power supply current
More informationSGM330A Quad, Wide-Bandwidth SPDT Video Analog Switch
GERAL DESCRIPTION The SGM330A is a quad, bidirectional, single-pole/doublethrow (SPDT) CMOS video analog switch (Mux/DeMux) designed to operate at a single +5V supply. This 2-channel multiplexer/demultiplexer
More informationSGM8706 Micro-Power, RRIO, 1.8V, Push-Pull Output Comparator with Integrated Voltage Reference GENERAL DESCRIPTION FEATURES APPLICATIONS
Micro-Power, RRIO, 1.V, Push-Pull Output GENERAL DESCRIPTION The is a low power comparator with a typical power supply current of 2.2µA. It features an uncommitted on-chip voltage reference, comparator
More informationSGM W Mono Fully Differential Audio Power Amplifier
.3W Mono Fully Differential GENERAL DESCRIPTION The SGM4995 is a fully differential audio power amplifier that is designed for portable communication device applications and demanding applications in mobile
More informationSGM8701 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator
SGM871 GENERAL DESCRIPTION The SGM871 is an ultra low power comparator with a typical power supply current of 3nA. It has the best-in-class power supply current versus propagation delay performance. The
More informationSGM Channel PWM Dimming Charge Pump White LED Driver
GENERAL DESCRIPTION The SGM3145 is a high performance white LED driver. It integrates current sources and automatic mode selection charge pump. The part maintains the high efficiency by utilizing a 1 /1.5
More information0.6Ω, Low-Voltage, Single-Supply, Dual SPDT Analog Switch
.6Ω, Low-Voltage, Single-Supply, Dual SPDT General Description The is a low on-resistance, low-voltage, dual single-pole/double throw (SPDT) analog switch that operates from a single 1.6V to 4.2V supply.
More informationSGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator
150ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power
More informationSGM4863 Dual 2.1W Audio Power Amplifier Plus Stereo Headphone Function
Dual.W Audio Power Amplifier GENERAL DESCRIPTION The SGM4863 is a dual bridge-connected audio power amplifier which, when connected to a 5V supply, will deliver.w into a 4Ω load or.5w into a 3Ω load with
More informationSGM mW, Capless, Stereo Headphone Amplifier with Shutdown
8mW, Capless, Stereo Headphone GENERAL DESCRIPTION The SGM497 stereo headphone amplifier is designed for portable equipment where board space is at a premium. The SGM497 uses capless architecture to produce
More informationAME. 1-Ohm Low Voltage SPDT Analog Switch AME4620. Functional Block Diagram. General Description. Features. Applications
4620 General Description The 4620 analog switches feature low ON resistance, single-pole, double-throw (SPDT) with wide operating single power supply voltage range, from 1.8V to 5.5V. Functional Block
More informationSGM MHz, 48μA, Rail-to-Rail I/O CMOS Operational Amplifier
PRODUCT DESCRIPTION The is a low cost, single rail-to-rail input and output voltage feedback amplifier. It has a wide input common mode voltage range and output voltage swing, and takes the minimum operating
More informationSGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator
45ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power consumption,
More informationFEATURES GENERAL DESCRIPTION PIN CONFIGURATIONS(TOP VIEW) APPLICATIONS SGM4157YD6 FUNCTION TABLE PIN DESCRIPTION 6 IN GND 5 V+ COM DFN-6 REV.
SPDT 1Ω Analog Switch GENERAL DESCRIPTION The is a single Low ON-Resistance(1Ω), fast single-pole double-throw (SPDT) CMOS switch. It is designed for low operating voltage, high current switching of speaker
More informationSGM2025 Quad, Low Power, Low Dropout, 200mA, RF-Linear Regulators
GENERAL DESCRIPTION The SGM2025 is a quad, low-power, low-dropout, CMOS linear voltage regulator that operates from 3.3V to 5.5V input and delivers up to 200mA continuous current at each channel. An ultra
More informationSGM8521/2/4 150kHz, 5.5μA, Rail-to-Rail I/O, CMOS Operational Amplifiers
//4 0kHz,.μA, Rail-to-Rail I/O, GENERAL DESCRIPTION The (single), SGM8 (dual) and SGM84 (quad) are low cost, rail-to-rail input and output voltage feedback amplifiers. They have a wide input common mode
More informationUM Ω Ultra Low ON-Resistance Dual SPDT Analog Switch UM5223 QFN General Description. Applications
0.5Ω Ultra Low ON-Resistance Dual SPDT Analog Switch UM5223 QFN10 1.8 1.4 General Description The UM5223 is a low on-resistance (R ON ), dual single-pole/double-throw (SPDT) analog switch operates from
More informationSGM W Fully Differential Audio Power Amplifier
.3W Fully Differential GENERAL DESCRIPTION The SGM4895 is a fully differential audio power amplifier that is designed for portable communication device applications and demanding applications in mobile
More information0.8Ω, Low-Voltage, Single-Supply Dual SPST Analog Switches
19-116; Rev ; 1/6.Ω, Low-Voltage, Single-Supply Dual SPST General Description The are low on-resistance, low-voltage, dual single-pole/single-throw (SPST) analog switches that operate from a single +1.6V
More informationFSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation
December 2013 FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation Features Low I CC When the S Input is Lower Than V CC Power-Off Isolation (V CC=0 V) 1 Ω On Resistance (R ON) for 4.5 V
More informationPI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP.
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.5Ω. Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation:
More information50Ω, Low-Voltage, Quad SPST/Dual SPDT Analog Switches in WLP
9-266; Rev 3; /2 5Ω, Low-Voltage, Quad SPST/Dual SPDT Analog General Description The low-voltage, quad single-pole single-throw (SPST)/dual single-pole/double-throw (SPDT) analog switches operate from
More informationSGM9119 Triple, 5th-Order, Standard Definition Video Filter Driver
PRODUCT DESCRIPTION The SGM9119 is a low voltage, triple video amplifier with integrated reconstruction filters and input clamps. Specially suited for standard definition video signals, this device is
More informationFEATURES BENEFITS APPLICATIONS. PARAMETER LIMIT UNIT Reference to GND V to +6 IN, COM, NC, NO a -0.3 to (V )
DESCRIPTION www.vishay.com.5, High Bandwidth, Dual SPDT Analog Switch The DGE is a low-voltage dual single-pole / double-throw monolithic CMOS analog switch. Designed to operate from. V to 5.5 V power
More informationSGM321/SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers
/SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers GENERAL DESCRIPTION The (single), SGM358 (dual) and SGM324 (quad) are low cost, rail-to-rail input and output voltage feedback amplifiers.
More informationPin Configurations/Functional Diagrams/Truth Table COM COM GND MAX4644 OFF OFF. Maxim Integrated Products 1
9-7; Rev ; 3/ High-Speed, Low-Voltage, 4Ω, General Description The is a single-pole/double-throw (SPDT) switch that operates from a single supply ranging from +.8V to +.V. It provides low 4Ω on-resistance
More informationTOP VIEW COUT1 COM2. Maxim Integrated Products 1
19-77; Rev ; 7/4.75Ω, Dual SPDT Audio Switch with General Description The dual, single-pole/double-throw (SPDT) switch operates from a single +2V to +5.5V supply and features rail-to-rail signal handling.
More informationUSB2.0 Hi-Speed and Audio Switches with Negative Signal Capability
BCT4153 with Negative Signal Capability GENERAL DESCRIPTION The BCT4153 is a double-pole double-throw (DPDT) analog switch with multiplexes USB2.0 and negative signal audio analog signals. One Channel
More informationSGM8621/2/3/4 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers
SGM8621/2/3/4 3MHz, Rail-to-Rail I/O PRODUCT DESCRIPTION The SGM8621 (single), SGM8622 (dual), SGM8623 (single with shutdown) and SGM8624 (quad) are low noise, low voltage, and low power operational amplifiers,
More informationSGM8631/2/3 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers
/2/3 6MHz, Rail-to-Rail I/O PRODUCT DESCRIPTION The (single), SGM8632 (dual) and SGM8633 (single with shutdown) are low noise, low voltage, and low power operational amplifiers that can be designed into
More informationLow-Voltage, High-Speed, Quad, SPST CMOS Analog Switches
9-5; Rev ; 7/99 Low-Voltage, High-Speed, Quad, SPST General Description The quad, low-voltage, high-speed, single-pole/single-throw (SPST) analog switches are pin compatible with the industry-standard
More informationFSA Ω Low-Voltage Dual DPDT Analog Switch
March 2013 FSA2467 0.4Ω Low-Voltage Dual DPDT Analog Switch Features Typical 0.4 On Resistance (R ON ) for +2.7V Supply Features Less then12µa ICCT Current when Sn Input is Lower than V CC 0.25 Maximum
More informationSGM9154 Single Channel, Video Filter Driver for HD (1080p)
PRODUCT DESCRIPTION The SGM9154 video filter is intended to replace passive LC filters and drivers with an integrated device. The 6th-order channel offers High Definition (HDp) filter. The SGM9154 may
More informationSGM8271/2/4 High Voltage Rail-to-Rail Output Operational Amplifiers
GENERAL DESCRIPTION The SGM8271 (single), SGM8272 (dual) and SGM8274 (quad) are high voltage operational amplifiers that are designed to offer a wide input common mode voltage range and output voltage
More informationSGM MHz, Triple, 6dB Video Driver
PRODUCT DESCRIPTION The SGM9117 includes triple high-speed video buffers with G = +2 in one package. Every video buffer has -db full signal bandwidth in excess of 2MHz, along with slew rates in excess
More informationSGM8631/2/3/4 470μA, 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers
PRODUCT DESCRIPTION The SGM863 (single), SGM863 (dual), SGM8633 (single with shutdown) and SGM8634 (quad) are low noise, low voltage, and low power operational amplifiers, that can be designed into a wide
More informationSGM89000 Capless 2Vrms Line Driver with Adjustable Gain
GENERAL DESCRIPTION The SGM89000 is a 2Vrms pop/click-free stereo line driver designed to allow the removal of the output DC-blocking capacitors for reduced component count and cost. The device is ideal
More information0.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854
.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854 FEATURES.8 Ω typical on resistance Less than 1 Ω maximum on resistance at 85 C 1.8 V to 5.5 V single supply High current carrying capability:
More informationSGM % Efficient Synchronous Step-Up Converter with 1.1A Switch
GERAL DESCRIPTION The SGM0 is a constant frequency, current mode, synchronous step-up switching regulator. It can be used for generating V at 00mA from a.v rail or a Li-Ion battery. High switching frequency
More informationADG1411/ADG1412/ADG1413
.5 Ω On Resistance, ±5 V/+2 V/±5 V, icmos, Quad SPST Switches ADG4/ADG42/ADG43 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel
More informationSGM706 Low-Cost, Microprocessor Supervisory Circuit
GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power-supply and monitor microprocessor activity. It significantly improves
More informationBCT4222B 350MHz DPDT Analog Switch
BCT4222B 350MHz DPDT Analog Switch Features VCC Operating Range: 1.65V to V Rail-to-Rail Signal Range ON-Resistance Matching: 0.04 Ω (TYP) ON-Resistance Flatness: 0.08Ω (TYP) High Off Isolation: 58dB at
More informationSGM8908 Capless 3Vrms Line Driver with Adjustable Gain
GENERAL DESCRIPTION The is a 3Vrms pop/click-free stereo line driver designed to allow the removal of the output DC-blocking capacitors for reduced component count and cost. The device is ideal for single
More informationSGM mA, High Voltage Regulators
Preliminary Datasheet SGM2203 GENERAL DESCRIPTION The SGM2203 series is a set of low power high voltage regulators implemented in CMOS technology which can provide 150mA output current. The device allows
More information20Ω, 300MHz Bandwidth, Dual SPDT Analog Switch in UCSP
9-2626; Rev ; /2 2, 3MHz Bandwidth, Dual SPDT Analog General Description The low-voltage, low on-resistance (R ON ), dual single-pole/double throw (SPDT) analog switch operates from a single +.8V to +5.5V
More informationMAX4680CWE. Pin Configurations/Functional Diagrams/Truth Tables N01 N.C. COM1 V- MAX4690 COM2 IN2 N.C. NO2 SSOP/SO/DIP SWITCH 2 ON OFF 1 OFF
19-1513; Rev ; 7/99 General Description The dual analog switches feature low on-resistance of 1.25Ω max. On-resistance is matched between switches to.3ω max and is flat (.3Ω max) over the specified signal
More informationSGM Ω, 300MHz Bandwidth, Dual, SPDT Analog Switch
GENERAL DESCRIPTION Th SGM4717 is a dual, bidirctional, singl-pol/ doubl-throw (SPDT) CMOS analog switch dsignd to oprat from a singl 1.8V to 5.5V supply. It faturs high-bandwidth (300MHz) and low on-rsistanc
More informationSGM % Efficient Synchronous Step-Up Converter with 1.1A Switch
GERAL DESCRIPTION The SGM0 is a constant frequency, current mode, synchronous step-up switching regulator. Its output currents can go as high as 7mA while using a single-cell alkaline, and discharge it
More informationMaxim Integrated Products 1
9-362; Rev 3; 6/7 Quad, SPST Analog Switch General Description The quad analog switch features on-resistance matching (4Ω max) between switches and guarantees on-resistance flatness over the signal range
More information10Ω, Quad, SPST, +3V Logic-Compatible Analog Switches
19-218; Rev 1; 9/8 1Ω, Quad, SPST, +3V Logic-Compatible General Description Maxim s analog switches feature low on-resistance (1Ω max) and 1.5Ω onresistance matching between channels. These switches are
More informationSub-Ω, Low Voltage, SPDT Analog Switches with Over Current Protection
New Product DG/DG1 Sub-Ω, Low Voltage, SPDT Analog Switches with Over Current Protection DESCRIPTION The DG/DG1 are low-voltage single single-pole/ double-throw monolithic CMOS analog switches. Designed
More information3 V/5 V CMOS 0.5 Ω SPDT/2:1 Mux in SC70 ADG849
3 V/5 V CMOS.5 Ω SPT/2: Mux in SC7 AG849 FEATURES Ultralow on-resistance:.5 Ω typical.8 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion:.3 Ω typical.24 Ω maximum RON flatness High
More informationPART MAX4503CPA MAX4503CSA. Pin Configurations 1 5 V+ COM N.C. V+ 4 MAX4504 MAX4503 DIP/SO
9-064; Rev ; /07 Low-Voltage, Dual-Supply, SPST, General Description The are low-voltage, dual-supply, single-pole/single-throw (SPST), CMOS analog switches. The is normally open (NO). The is normally
More informationAutomotive 125 C Analog Switch Dual DPDT / Quad SPDT, 0.37, 338 MHz Bandwidth
Automotive 125 C Analog Switch Dual DPDT / Quad SPDT, 0.37, 338 MHz Bandwidth DESCRIPTION The, is a four-channel single-pole double-throw (SPDT) analog switch with two control inputs. It is also known
More informationPA R T NC1 A0 V+ EN CONTROL LOGIC A0 NC1 EN 1 MAX4674 COM2 QFN. Maxim Integrated Products 1
9-78; Rev 3; 2/6 3V/5V, 4Ω, Wideband Quad 2: Analog Multiplexer General Description The is a low-voltage CMOS analog switch containing four 2: multiplexers/demultiplexer. When powered from a single +5V
More informationSGM8554 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier
PRODUCT DESCRIPTION The SGM8554 is a quad rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to 5.5V
More informationSGM8584 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier
PRODUCT DESCRIPTION The SGM8584 is a quad rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to 5.5V
More information1.3 Ω CMOS, 1.8 V to 5.5 V Single SPDT Switch/2:1 MUX in SOT-66 Package ADG859
1.3 Ω CMOS, 1.8 V to 5.5 ingle SPT Switch/2:1 MUX in SOT-66 Package AG859 FEATURES 1.8 V to 5.5 V single supply Tiny 1.65 mm 1.65 mm package Low on resistance: 1.3 Ω at 5 V supply High current-carrying
More informationSGM3122 White LED Charge Pump Current Source with PWM Brightness Control
GENERAL DESCRIPTION The SGM3122 is a charge pump with PWM brightness control for white LED supplies in LCD display backlight applications. The supply voltage ranges from 2.7V to 5.5V, it is ideally suited
More informationMAX4684/MAX4685 OFF ON 1 SWITCHES SHOWN FOR LOGIC "0" INPUT
19-1977; Rev 4; 1/9.5Ω/.8Ω Low-Voltage, Dual SPDT General Description The low on-resistance (R ON ), lowvoltage, dual single-pole/double-throw (SPDT) analog switches operate from a single +1.8V to +5.5V
More information5Ω, Quad, SPST, CMOS Analog Switches
9-393; Rev ; 8/99 5Ω, Quad, SPST, CMOS Analog Switches General Description The quad analog switches feature 5Ω max on-resistance. On-resistance is matched between switches to.5ω max and is flat (.5Ω max)
More information3110(A) SGM3110 MicroPower Regulated Charge Pump FEATURES GENERAL DESCRIPTION PIN CONFIGURATION (TOP VIEW) APPLICATIONS TYPICAL APPLICATION
GENERAL DESCRIPTION The SGM30 is a MicroPower switched capacitor voltage converter that delivers a regulated output. No external inductor is required for operation. The SGM30 can deliver up to 00mA to
More informationFEATURES DG2538, MSOP-10 V+ 1 V+ COM 1. Top View. Temperature Range Package Part Number
Dual SPST Switches DG, DG8, DG9 DESCRIPTION The DG, DG8, and DG9 are low voltage, precision dual SPST switches that can be operated in a single supply or in a dual supply configuration power supply with
More information