TIP2955 PNP SILICON POWER TRANSISTOR

Transcription

1 Designed for Complementary Use with the TIP3055 Series 90 W at 5 C Case Temperature 15 A Continuous Collector Current Customer-Specified Selections Available B C SOT-93 PACKAGE (TOP VIEW) 1 E 3 Pin is in electrical contact with the mounting base. MDTRAAA absolute maximum ratings at 5 C case temperature (unless otherwise noted) RATING SYMBOL VALUE UNIT Collector-base voltage (I E = 0) V CBO -100 V Collector-emitter voltage (I B = 0) (see Note 1) V CER -70 V Emitter-base voltage V EBO -7 V Continuous collector current I C -15 A Continuous base current I B -7 A Continuous device dissipation at (or below) 5 C case temperature (see Note ) P tot 90 W Continuous device dissipation at (or below) 5 C free air temperature (see Note 3) P tot 3.5 W Unclamped inductive load energy (see Note 4) ½LI C 6.5 mj Operating junction temperature range T j -65 to +150 C Storage temperature range T stg -65 to +150 C Lead temperature 3. mm from case for 10 seconds T L 60 C NOTES: 1. This value applies when the base-emitter resistance R BE = 100 Ω.. Derate linearly to 150 C case temperature at the rate of 0.7 W/ C. 3. Derate linearly to 150 C free air temperature at the rate of 8 mw/ C. 4. This rating is based on the capability of the transistor to operate safely in a circuit of: L = 0 mh, I B(on) = -0.4 A, R BE = 100 Ω, V BE(off) = 0, R S = 0.1 Ω, V CC = -10 V. 1

2 electrical characteristics at 5 C case temperature PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Collector-emitter V (BR)CEO I breakdown voltage C = -30 ma I B = 0 (see Note 5) -60 V I CEO I CEV I EBO h FE V CE(sat) V BE h fe h fe Collector cut-off current Voltage between base and emitter Emitter cut-off current Forward current transfer ratio Collector-emitter saturation voltage Base-emitter voltage Small signal forward current transfer ratio Small signal forward current transfer ratio V CE = -30 V I B =0-0.7 ma V CE = -100 V V BE = 1.5 V -5 ma V EB = -7 V I C =0-5 ma V CE = V CE = I B = I B = -4 V -4 V -0.4 A -3.3 A I C = - 4A I C = -10 A I C = - 4A I C = -10A (see Notes 5 and 6) (see Notes 5 and 6) V CE = -4 V I C = -4 A (see Notes 5 and 6) -1.8 V V CE = -10 V I C = -0.5 A f = 1 khz 0 V CE = -10 V I C = -0.5 A f = 1 MHz 3 NOTES: 5. These parameters must be measured using pulse techniques, = 300 µs, duty cycle %. 6. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts V thermal characteristics PARAMETER MIN TYP MAX UNIT R θjc Junction to case thermal resistance 1.39 C/W R θja Junction to free air thermal resistance 35.7 C/W resistive-load-switching characteristics at 5 C case temperature PARAMETER TEST CONDITIONS MIN TYP MAX UNIT t on Turn-on time I C = -6 A I B(on) = -0.6 A I B(off) = 0.6 A 0.4 µs t off Turn-off time V BE(off) = 4 V R L = 5 Ω = 0 µs, dc % 0.7 µs Voltage and current values shown are nominal; exact values vary slightly with transistor parameters.

3 TYPICAL CHARACTERISTICS 1000 TYPICAL DC CURRENT GAIN vs COLLECTOR CURRENT V CE = -4 V T C = 5 C = 300 µs, duty cycle < % TCS638AD h FE - DC Current Gain I C - Collector Current - A Figure 1. MAXIMUM SAFE OPERATING REGIONS I C - Collector Current - A MAXIMUM FORWARD-BIAS SAFE OPERATING AREA SAS638AB = 300 µs, = 1 ms, = 10 ms, DC Operation V CE - Collector-Emitter Voltage - V Figure. 3

4 THERMAL 100 MAXIMUM POWER DISSIPATION vs CASE TEMPERATURE TIS637AB P tot - Maximum Power Dissipation - W T C - Case Temperature - C Figure 3. 4

5 MECHANICAL DATA SOT-93 3-pin plastic flange-mounackage This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuierformance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. SOT-93 4,90 4,70 ø 4,1 4,0 15, 14,7 3,95 4,15 1,37 1,17 1, MAX. 16, MAX. 31,0 TYP. 18,0 TYP ,30 1,10 0,78 0,50 11,1 10,8,50 TYP. ALL LINEAR DIMENSIONS IN MILLIMETERS NOTE A: The centre pin is in electrical contact with the mounting tab. MDXXAW 5