luxcontrol masterconfigurator Product Manual

Transcription

1 luxcontrol masterconfigurator Produt Manual

2 Table of ontents 2 Sgns and symbols Changes ntrodued... wth masterconfigurator Introduton Installaton Atve wndow Commssonng Seletng an nterfae Optons Flter settngs edali addressng Multmaster Improvements Testng the nstallaton Addressng Testng addressng Groupng ontrol... gear Settng senes Savng a projet General funtons Searhng for deves Changng a deve... name Creatng a new... group Changng a group... name Assgnng a DALI... deve to a group Assgnng a DALI... deve to more than one group Removng a DALI... deve from a group Deletng a DALI... deve Chekng deve... assgnment 35 8 Confguraton DALI ontrol gear Deve nformaton Bas onfguraton Status Trdon-spef onfguraton Deve Type 0: Control... gear for fluoresent lamps Deve Type 1: Control... gear for emergeny lghtng Deve Type 2: Control... gear for hgh-pressure dsharge lamps 130 2

3 8.1.8 Deve Type 3: Control... gear for low-voltage halogen lamps Deve Type 4: Control... gear for phase dmmers Deve Type 6: Control... gear for LEDs Deve Type 7: Control... gear for swthng funton Deve Type 8: Control... gear for olour onverters Deve Type 255: Mult-deve... types DALI XC Bas onfguraton Confguraton of operatng... mode "MC" Status 8.3 DALI MC DALI basdim... DGC Bas onfguraton Room profles Deve-spef onfguraton Status Lght sensor Moton sensor Remote ontrol DALI MSensor MSensor 5DPI DALI MSensor 02 (verson ) DALI MSensor (verson and 1.7) DALI MSensor (verson ) DALI TOUCHPANEL User-defned onfguraton Tunable Whte Fatory settngs DALI PS2 Standby DALI-Somfy anmeo... Interfae Quk test 9 Tools Command admnstrator DALI ommands DSI ommands Command sequene Control gear wzard Loalsaton wzard... for DALI XC Frmware update Further omponents Appendx 3

4 11.1 Confguraton... ommands for DALI ontrol gear Swth and dm... ommands Query ommands Reset values Doument verson

5 Sgns and symbols 1 Sgns and symbols The followng haraters and symbols are used n ths manual: 1. Indvdual steps n the nstrutons are numbered. Sngle-step nstrutons are ndated by at the begnnng of the lne. After a step has been desrbed, a desrpton of the expeted results wll follow. These results are ndated by at the begnnng of the lne. Requrements whh need to be heked before arryng out a step are ndated by. Indvdual notes an be reognsed by. In addton, notes are dentfed by the word. 5

6 Changes ntrodued wth masterconfigurator Changes ntrodued wth masterconfigurator 2.28 Improvements Searh speed optmzed, further optmzatons and bug fxes New program and toolbar ons Enhanements New Trdon-spef parameters added. New ontrol gear added. New DALI BusServer wth DALI montor 6

7 Introduton 3 Introduton The masterconfigurator software s a onfguraton and parametersaton program for DALI deves. Ths software an be used to set up a DALI ontrol lne and onfgure ndvdual ontrol gear and ontrol unts. Bas funtons Addressng Groupng Settng senes Parametersng DALI deves Confgurng DALI and DSI ommands Creatng ommand sequenes Testng nstallaton, addressng and funtons The masterconfigurator software s desgned for onlne operaton. If DALI deves are onfgured offlne, faults may our. 7

8 Installaton 4 Installaton Ths seton overs the system requrements for the masterconfigurator software and how the software s nstalled. System requrements In order to make full use of the funtonalty of the masterconfigurator software, the followng are requred: Operatng system Wndows 7: only ompatble wth DALI USB frmware verson 1.4 or hgher (August 2008); ompatblty mode: Wndows XP (Serve Pak 3) Wndows XP The hapter Changng ompatblty mode an hange the ompatblty mode. Sreen resoluton Mnmum XGA (1024 x 768 pxels) Communaton USB or COM nterfae 10 wll tell you how you Table 1: System requrements Installng software as admnstrator 1. Run the fle masterconfigurator_vxxx.exe as admnstrator. a. Rght-lk on fle. Submenu s dsplayed. b. Clk on Run as admnstrator. 2. Clk on Next. The setup wzard appears. 3. Follow the setup wzard steps. The masterconfigurator software s nstalled. The masterconfigurator software an be aessed by gong to Start > Programs > Trdon > masterconfigurator or va the desktop. shortut on the Installng software wthout admnstratve rghts 1. Run the fle masterconfigurator_vxxx.exe. 2. Clk on Next. The setup wzard appears. 3. Follow the setup wzard steps. The masterconfigurator software s nstalled. 4. Follow the setup wzard steps. The DALI BusServer software s nstalled. 8

9 Installaton If the masterconfigurator software s nstalled wthout admnstraton rghts, an nstallaton path wth wrte permsson must be seleted. An nstallaton to the default path s not possble beause of mssng wrte permsson for non-admnstrators. The masterconfigurator software an be aessed by gong to Start > Programs > Trdon > masterconfigurator or va the desktop. shortut on the 9

10 Installaton Changng ompatblty mode The ompatblty mode only has to be hanged f Mrosoft Wndows 7 s used as the operatng system. 1. On the desktop, rght-lk on the on. 2. Selet menu tem Propertes. 3. Clk on the Compatblty tab. 4. Enable the Run program n ompatblty mode hekbox. 5. In the dropdown lst, selet Wndows XP (Serve Pak 3). 6. Clk OK. Compatblty mode has been hanged. 10

11 Atve wndow 5 Atve wndow After startng up, the software dsplays the atve wndow. The ontrol gear and ontrol unts an be parametersed and onfgured here. Dependng on the funton, further sub-wndows wll be opened. Name Funton (1) Ttle bar Dsplays the name of the projet fle urrently open. (2) Menu bar Contans the Fle, Settngs, Commssonng, Tools and Vew menus. (3) Toolbar Contans ons for quk aess to varous funtons. You an show or hde the toolbar va menu tem Vew > Toolbar. (4) DALI deve tree dagram Dsplays the deves onneted to the DALI ontrol lne n a tree dagram. It s also possble to see whh group eah deve belongs to. (5) Detal vew Dsplays the propertes of a deve or a group that has been seleted n the DALI deve tree dagram. The deves or groups an be onfgured and parametrsed here. (6) Status bar Dsplays status nformaton and help text. You an show or hde the status bar va menu tem Vew > Status bar. Table 2: Atve w ndow 11

12 Atve wndow Toolbar The followng ons are found n the toolbar: Ion Funton Create a new projet Open a projet Save a projet Prnt a projet Loate Identfy Table 3: Toolbar A detaled desrpton of the Loate and Identfy funtons an be found n Seton Chekng deve assgnment Changng the language The software user nterfae an be dsplayed n German or Englsh. The language s hanged as follows: 1. Selet Vew. 2. Selet language. A message appears ndatng that the language wll only be hanged after the program has been restarted. 3. Confrm the message by lkng on OK. 4. Restart the program. The software wll be started n the desred language. Showng/hdng advaned settngs Control gear and ontrol unts an be onfgured usng the masterconfigurator. The advaned settngs must be dsplayed n order to onfgure addtonal parameters as well as the general settngs. The advaned settngs an be shown or hdden as follows: 1. Selet Vew. 2. Show (enable) or hde (dsable) the Advaned settngs. The advaned settngs are shown/hdden n the detal vew. 12

13 Atve wndow The advaned settngs must be enabled agan eah tme the software s restarted. 13

14 Commssonng 6 Commssonng The masterconfigurator software allows the user to test the orret wrng of the DALI ontrol lne, address the deves and defne group and sene settngs n fve easy steps. In order for these steps to be arred out, an nterfae must frst be seleted. Optonally, the deve searh and the addressng an be narrowed down. 6.1 Seletng an nterfae Use a DALI USB or the ready2mans Programmer for exhangng data between the omputer and the deves on the DALI ontrol lne. For bakward ompatblty, DALI SCI2 an be used. DALI SCI s not supported. If the omputer s already onneted to the DALI ontrol lne va an nterfae, the masterconfigurator software automatally detets the type of nterfae and selets t for ommunaton. However, the nterfae may also be seleted manually. Seletng an nterfae manually 1. Connet the USB able of the DALI USB or the ready2mans Programmer to the omputer on whh the masterconfigurator software s nstalled. 2. Connet the DALI USB or the ready2mans Programmer to the DALI ontrol lne. 3. Selet Settngs > Selet nterfae The Selet nterfae pop-up wndow appears. 4. To use a USB nterfae, selet the USB rado button and selet the desred nterfae from the drop-down lst. 5. To use a COM nterfae, selet the COM rado button and selet the desred nterfae from the drop-down lst. 6. Confrm the seleton by lkng on OK. The nterfae has been seleted. DALI BusServer starts automatally. 14

15 Commssonng If the masterconfigurator software detets that a DALI USB s onneted, t automatally heks the USB software verson. If t s older than the verson suppled wth the masterconfigurator software, t wll be updated automatally. Ths update takes approxmately one mnute. 6.2 Optons Under Settngs > Optons the followng funtons an be set: Flter settngs ed addressng Multmaster Improvements Flter settngs Ths funton allows the user to narrow the deve searh or addressng. Enablng the flter 1. Selet Settngs > Optons. The Optons pop-up wndow appears. 2. Clk on the Flter tab. 3. Selet the hekbox to nlude deves n the deve searh and addressng. 4. Confrm the seleton by lkng on OK. 15

16 Commssonng Flter for the deve searh and the addressng s enabled. Only those deves wth enabled hekboxes wll be nluded n the deve searh and the addressng edali addressng Up to 64 ed addresses an be assgned when addressng ed deves. The 64 ed addresses an be onfgured to be assgned one per DALI ontrol lne or one per deve lass. Dsablng the opton 1. Selet Settngs > Optons. The Optons pop-up wndow appears. 2. Clk on the ed addressng tab. 3. Dsable the hekbox. 4. Confrm the seleton by lkng on OK. The type of ed addressng has been hanged. Ths hange wll be appled when the system s next re-ntalsed (New ntalsaton). Both types of ed addressng are explaned n the followng examples. Example 1: Assgn ed address (0-63) only one enabled: The ed addresses are assgned one per DALI ontrol lne. Example 2: Assgn ed address (0-63) only one dsabled: The ed addresses are assgned one per deve lass. 16

17 Commssonng Example 1: ed addresses assgned one per DALI ontrol lne Deve lass ed address Explanaton DALI MSensor: lght sensor ea 0 The frst of 64 ed addresses has been assgned on ths DALI ontrol lne. DALI MSensor: moton sensor ea 1 The seond of 64 ed addresses has been assgned on ths DALI ontrol lne. DALI MSensor: remote ontrol ea 2 The thrd of 64 ed addresses has been assgned on ths DALI ontrol lne. DALI MC ea 3 The fourth of 64 ed addresses has been assgned on ths DALI ontrol lne. Table 4: Example of ed addressng, opton enabled In ths example a total of four out of 64 ed addresses have been assgned. Another 60 ed addresses an stll be assgned on ths DALI ontrol lne. 17

18 Commssonng Example 2: ed addresses assgned one per deve lass Deve lass ed address Explanaton DALI MSensor: lght sensor ea 0 The frst of 64 ed addresses has been assgned to the "Lght sensor" deve lass. DALI MSensor: moton sensor ea 0 The frst of 64 ed addresses has been assgned to the "Moton sensor" deve lass. DALI MSensor: remote ontrol ea 0 The frst of 64 ed addresses has been assgned to the "Manual ontrol unts" deve lass. DALI MC ea 1 The seond of 64 ed addresses has been assgned to the "Manual ontrol unts" deve lass. Table 5: Example of ed addressng, opton dsabled In ths example only one of the 64 ed addresses has been assgned to eah of the "Lght sensor" and "Moton sensor" deve lasses. Another 63 ed addresses an stll be assgned to eah deve lass. Two of the 64 ed addresses have been assgned to the "Manual ontrol unts" deve lass. Another 62 ed addresses an stll be assgned to ths deve lass. 18

19 Commssonng Multmaster Ths funton s enabled by default and prevents ontrol deves from transmttng frames durng frmware updates. Wth ths, t s possble to avod onfltng ommands from the masterconfigurator and other ontrol deves va the DALI lne. Dsablng the opton 1. Selet Settngs > Optons. The Optons pop-up wndow appears. 2. Clk on the Multmaster tab. 3. Dsable the hekbox. 4. Confrm the seleton by lkng on OK. Set the masterconfigurator as multmaster head has been deatvated. Ths hange wll be appled when the system s next re-ntalsed (New ntalsaton). Both types of Multmaster are explaned n the followng examples. Example 1: Set the masterconfigurator as multmaster head enabled: The masterconfigurator s set as multmaster head. Other ontrol deves annot transmt frames durng a frmware update. Example 2: Set the masterconfigurator as multmaster head dsabled: Other ontrol deves an transmt frames durng a frmware update. 19

20 Commssonng Improvements Ths funton s enabled by default and allows the applaton to trak nformaton about the funtons used. Dsablng the opton 1. Selet Settngs > Optons. The Optons pop-up wndow appears. 2. Clk on the Improvements tab. 3. Dsable the hekbox. 4. Confrm the seleton by lkng on OK. Allow data trakng to mprove user experene has been deatvated. Ths hange wll be appled when the system s next re-ntalsed (New ntalsaton). 20

21 Commssonng 6.3 Testng the nstallaton Ths funton allows the user to test the wrng of the nstallaton. Testng the nstallaton 1. Selet Commssonng > 1. Test nstallaton. The Exeute test pop-up wndow appears. 2. Enter an nterval between 1 and 10 seonds. 3. Clk on Start. The Start button hanges nto the Stop button. One the test s started, the mnmum level and maxmum level ommands are sent alternately to all lumnares on the DALI ontrol lne. 4. Clk on Stop to stop the test. 6.4 Addressng Addressng an be arred out usng the addressng wzard. There are generally two ways to address deves: New ntalsaton: all addresses and group membershps are deleted n the deves. The deves are then readdressed. System extenson (address prevously unaddressed deves): a searh s arred out for prevously addressed and unaddressed deves. Addressng for prevously addressed deves wll reman unhanged. The next avalable address s then assgned to deves whh have been reently added. In the event of system extenson, reently added deves annot already have an address. Otherwse, duplate addresses ould be assgned, whh would lead to problems. 21

22 Commssonng Addressng Requrements: Installaton test ompleted suessfully. No lamp errors. Optonal: flter enabled. 1. Selet Commssonng > 2. Address. The addressng wzard appears. 2. Selet rado button New ntalsaton or System extenson (address prevously unaddressed deves). If no other optons are seleted, the addresses are assgned at random. 3. To set other addressng optons, lk on Optons. Further optons appear. 22

23 Commssonng 4. To address lumnares spefally n aordane wth the addressng plan usng the physal seleton method, selet Lumnares. The way n whh the physal seleton method s arred out dffers from deve to deve and should therefore be taken from the doumentaton spefally for the deve n queston. Not all DALI ontrol gear supports ths type of addressng. Before addressng, hek whether the onneted ontrol gear supports the physal seleton method. 5. To address ontrol unts spefally aordng to the addressng plan usng the physal seleton method, selet Control unts. Seton Speal notes on addressng ontrol unts 24 ontans nformaton on how ontrol unts are addressed usng the physal seleton method. 6. To address lumnares so that no reaton s vsble n the room, selet Addressng wthout vsble reaton. If lumnares are addressed wth the physal seleton method, the Addressng wthout vsble reaton funton s gnored. Addressng wthout vsble reaton s reommended f the rooms are already n use and the system s just beng extended. In the ase of addressng wth a vsble reaton, the lumnare beng addressed goes to the maxmum level. 7. Clk on Next. Addressng s arred out n aordane wth the seleted optons. Found deves are lsted n the pop-up wndow. The assgned address s shown n brakets, wth A standng for DALI address and ea for ed address. 8. As soon as the addressng s omplete, a message appears. 23

24 Commssonng 9. Clk Done to ext the addressng wzard. Found deves are shown n the DALI deve tree dagram. Speal notes on addressng ontrol unts Control unts suh as the DALI MC or the DALI TOUCHPANEL must be addressed wth the physal seleton method. When addressng ontrol unts, the user s prompted to press a key on the ontrol unt to address the deve. 24

25 Commssonng Addressng the DALI MC 1. Press the key on the DALI MC twe ("double-lk"). The masterconfigurator software reognses the nput and assgns an ed address (ea) to t. 2. Repeat the proess for all four DALI MC nputs. The ed addresses (ea) are assgned n the order n whh the keys on the DALI MC are pressed. Addressng the DALI TOUCHPANEL Press any key on the DALI TOUCHPANEL. The masterconfigurator software reognses the nput and assgns an ed address (ea) to t. A total of 64 addresses an be assgned on the DALI ontrol lne. The ed addresses gven to the DALI MC and the DALI TOUCHPANEL do not redue ths number. 25

26 Commssonng 6.5 Testng addressng Ths funton allows the user to test the addressng. Testng addressng 1. Selet Commssonng > 3. Chek addressng. The Exeute test pop-up wndow appears. The number of addressed ontrol gear elements s shown under Total of addressed ontrol gear. 2. Enter an nterval between 1 and 10 seonds. 3. Clk on Start. The Start button hanges nto the Stop button. One the test s started, the maxmum level s sent to all lumnares n order. The orrespondng address appears under Control gear to maxmum value wth address. 4. Clk on Stop to stop the test. 26

27 Commssonng 6.6 Groupng ontrol gear Ths funton allows the user to group ontrol gear. Up to 16 groups (0 15) are avalable. Groupng ontrol gear 1. Selet Commssonng > 4. Group ontrol gear. The Group ontrol gear pop-up wndow appears. The left-hand olumn lsts all the avalable ontrol gear. The rght-hand olumn shows all the deves that are n the seleted group. 2. Selet the desred group (0 15) from the Group drop-down lst. 3. Optonally, selet the Loalse hekbox. The seleted lumnare goes to the maxmum level. 4. Selet the ontrol gear n the left-hand olumn. 5. To add ontrol gear to the group, lk on Add. The ontrol gear s removed from the left-hand olumn. It s added to the seleted group and appears n the rghthand olumn. Removng ontrol gear from a group 1. Selet the ontrol gear n the left-hand olumn. 2. Clk on Remove. The ontrol gear s removed from the group and appears n the left-hand olumn. 27

28 Commssonng 6.7 Settng senes Ths funton allows the user to onfgure up to 16 senes (0 15). Settng senes Requrement: Deves assgned to the groups. 1. Selet Commssonng > 5. Set senes. The Set senes pop-up wndow appears. 2. Selet the desred sene (0 15) from the drop-down lst. All the followng settngs are defned for ths sene. 3. Selet the hekbox to assgn an ntensty to all the lumnares n the group. 4. Enter a value between 0% and 100%. All the ontrol gear n ths group mmedately go to the entered level. 5. Confrm the entry by lkng on OK. Settngs are saved for ths group. 6. To defne the settngs for the other senes, repeat steps 2 to 5 for eah sene. MASK means that the lumnares n ths group wll retan ther urrent ntensty when the relevant sene s realled. 28

29 Commssonng 6.8 Savng a projet Ths funton allows the user to save the ommssonng n a *.dn fle. 1. Selet Fle > Save. The Save fle pop-up wndow appears. 2. Selet a loaton for the fle. 3. Enter the fle name. 4. Clk on Save. The projet s saved. -or- 1. In the toolbar, lk on. The Save fle pop-up wndow appears. 2. Selet a loaton for the fle. 3. Enter the fle name. 4. Clk on Save. The projet s saved. 29

30 General funtons 7 General funtons After addressng, the deves are dsplayed n the DALI deve tree dagram. If deves have already been assgned to a group (see Seton Groupng ontrol gear 27 ), ths group s reated automatally and the deves are assgned to t. DALI deves an be assgned to more than one group at the same tme. Group membershp an be seen n the detal vew. 7.1 Searhng for deves Requrements: Installaton test ompleted suessfully. No lamp errors. Optonal: flter enabled. 1. In the DALI deve tree dagram, rght-lk on the The ontext menu appears. on. 2. Selet Searh deves n the ontext menu. The searh s arred out wth the addressng wzard. Found deves are lsted n the pop-up wndow. The assgned address s shown n brakets, wth A standng for DALI address and ea for ed address. 30

31 General funtons 3. One the searh s fnshed, a message appears. 4. Clk Done to ext the addressng wzard. Found deves are shown n the DALI deve tree dagram. For more nformaton on the settng optons for the addressng wzard, please refer to Seton Addressng Changng a deve name 1. In the DALI deve tree dagram, rght-lk on the deve name to be hanged. The ontext menu appears. 2. Selet Rename n the ontext menu. 3. Change the deve name dretly n the DALI deve tree dagram. 4. Confrm the entry by pressng ENTER. The deve name s hanged. -or1. In the DALI deve tree dagram, selet the deve name to be hanged. 2. Press F2. 3. Change the deve name dretly n the DALI deve tree dagram. 4. Confrm the entry by pressng ENTER. The deve name s hanged. When a deve s renamed, the abbrevaton n brakets dsappears. One the new name s onfrmed, however, the abbrevaton automatally reappears n the brakets. 31

32 General funtons 7.3 Creatng a new group 1. In the DALI deve tree dagram, rght-lk on the The ontext menu appears. on. 2. Selet Create new group n the ontext menu. The next free group s automatally added to the DALI deve tree dagram. 7.4 Changng a group name 1. In the DALI deve tree dagram, rght-lk on the group name to be hanged. The ontext menu appears. 2. Selet Rename n the ontext menu. 3. Change the group name dretly n the DALI deve tree dagram. 4. Confrm the entry by pressng ENTER. The group name s hanged. -or1. In the DALI deve tree dagram, selet the group name to be hanged. 2. Press F2. 3. Change the group name dretly n the DALI deve tree dagram. 4. Confrm the entry by pressng ENTER. The group name s hanged. When a group s renamed, the abbrevaton n brakets dsappears. One the new name s onfrmed, however, the abbrevaton automatally reappears n the brakets. 7.5 Assgnng a DALI deve to a group 1. In the DALI deve tree dagram, lk on the deve to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the deve to the approprate group. (Drag & Drop) The deve s removed from the group n whh t was prevously loated and s added to the desred group. -or1. In the DALI deve tree dagram, rght-lk on the deve to be assgned to a group. 2. Hold down the rght mouse button. 3. Drag the deve to the approprate group. 4. Release the rght-hand mouse button. 5. Selet Move. The deve s removed from the group n whh t was prevously loated and s added to the desred group. 32

33 General funtons Seton DALI MSensor 02 > Effetve range DALI MSensor 02 to a group. 213 ontans nformaton on how to assgn a Seton DALI MSensor (verson 1.5) > Effetve range 229 ontans nformaton on how to assgn a DALI MSensor (verson 1.5 and lower) to a group. 7.6 Assgnng a DALI deve to more than one group One DALI deve an be assgned to multple groups. To do ths, the DALI deve s frst oped and then assgned to the desred groups. 1. In the DALI deve tree dagram, lk on the deve to be oped and assgned to a group. 2. Hold down the left mouse button. 3. In addton, hold down the CTRL key. 4. Drag the deve to the approprate group. The deve s oped. It s now n both groups. -or1. In the DALI deve tree dagram, rght-lk on the deve to be oped and assgned to a group. 2. Hold down the rght mouse button. 3. Drag the deve to the approprate group. 4. Release the rght-hand mouse button. 5. Selet Copy. The deve s oped. It s now n both groups. 7.7 Removng a DALI deve from a group 1. Clk on the deve to be removed from a group. 2. Hold down the left mouse button. 3. Drag the deve to the on. The deve s removed from the group and appears one agan n the DALI deve tree dagram wthout a group. -or1. Rght-lk on the deve to be removed from a group. The ontext menu appears. 2. Selet Remove deve from group n the ontext menu. The deve s removed from the group and appears one agan n the DALI deve tree dagram wthout a group. 33

34 General funtons 7.8 Deletng a DALI deve 1. Rght-lk on the deve to be deleted. The ontext menu appears. 2. Selet Delete from the ontext menu. A message appears, promptng for onfrmaton that the seleted deve should be deleted. 3. Confrm the aton by lkng on Yes. The deve s deleted from the DALI deve tree dagram. The deve's address s deleted. -or1. In the DALI deve tree dagram, selet the deve to be deleted. 2. Press DEL. A message appears, promptng for onfrmaton that the seleted deve should be deleted. 3. Confrm the aton by lkng on Yes. The deve s deleted from the DALI deve tree dagram. The deve's address s deleted. 34

35 General funtons 7.9 Chekng deve assgnment There are varous ways to hek the deve assgnment to the physally exstng groups. Ion Desrpton The Loate on an be used to determne where bus subsrbers are loated or whh address they have. A sngle deve, a group or all the deves onneted to the DALI ontrol lne an be loated. The type of loaton method depends on the deve. There are two types of method: vsual and aoust. Vsual loaton: type of loaton n whh the address of a bus subsrber s used to vsually loate ths subsrber n the feld. A vsually loated lumnare, for example, responds by swthng to the maxmum level. A vsually loated emergeny lumnare, for example, responds by forwardng ts address as a bnary flashng pattern va the status LED. Aoust loaton: type of loaton n whh the address of a bus subsrber s used to aoustally loate ths subsrber n the feld. An aoustally loated sensor, for example, responds by beepng. The followng deves an be loated: DALI ontrol gear Speal note for ontrol gear for emergeny lghtng: Only ever one ontrol gear element for emergeny lghtng an be loated. Loatng all of the deves onneted to the DALI ontrol lne s only possble wth the Identfy on. Input deves Sensors The Identfy on an be used to determne where an emergeny lumnare wth a spef DALI short address s loated. If the funton s enabled, all of the emergeny lumnares onneted to the DALI ontrol lne respond by forwardng ther address as a bnary flashng pattern va the status LED. The followng deves an be dentfed: DALI ontrol gear for emergeny lghtng Table 6: Optons for hekng deve assgnment The two funtons Loate und Identfy are hghlghted n dfferent olor for better dstnton. Loate: Bakground olor yellow. Identfy: bakground olor green. 35

36 General funtons Tps & trks If an on s hghlghted n blue n the toolbar, the funton s enabled. After hekng the deve assgnment, the funton used must be dsabled va the orrespondng on. Otherwse the deves wll ontnue to respond aordng to the respetve funton. To loate an ndvdual deve va the To loate a group va the on, selet the orrespondng deve n the DALI deve tree dagram. on, selet the group n the DALI deve tree dagram. To loate all of the deves onneted to the DALI ontrol lne va the deve tree dagram. on, selet the on n the DALI 36

37 General funtons Emergeny lumnares forward ther address as a bnary flashng pattern va the status LED. For ths purpose, the address s onverted nto a sx-dgt bnary number, whh s represented as a flashng pattern. The red LED stands for bnary number 0, the green LED for bnary number 1. The followng optons are avalable to users n order to onvert a bnary number to a demal number: EM PRO Ident.TOOL software: You an download ths software from Trdon's homepage at: Serves Software. EM PRO addressng tool (Artle number ) 37

38 Confguraton 8 Confguraton The masterconfigurator software an be used to onfgure the followng deves: DALI ontrol gear DALI XC 159 DALI MC DALI basdim DGC DALI MSensor DALI TOUCHPANEL DALI PS2 Standby DALI Somfy anmeo nterfae 250 A deve that has been seleted n the DALI deve tree dagram an be onfgured n the detal vew. The followng funtons are avalable n the upper part of the detal vew: Funton Desrpton Read The settngs stored n the deve are read and dsplayed n the detal vew. Save Changes are stored n the deve. Quk test The onfguraton of the ontrol gear an be tested n the Quk test pop-up wndow. A detaled desrpton of the quk test an be found n Seton Quk test Readdress The address of the deve s hanged. If the desred address has already been assgned to another deve on the DALI ontrol lne, the addresses of the two deves are swapped. For the swap to take plae, however, at least one address must be free. Fatory settngs The deve s reset to ts fatory settngs. Not every ontrol gear element supports ths funton. Table 7: General funtons Not every deve supports all funtons. Funtons whh are not supported are greyed out. When onfgurng a deve wth the above-mentoned funtons, the addressng s ontrolled. In ase of falure (deve no longer aessble, no supply, et.) the followng error message s dsplayed: 38

39 Confguraton 39

40 Confguraton The followng table ontans nformaton about whh deves support whh funtons: Deve Read Save Quk test Readdress Fatory settngs Control gear for DALI V1 Control gear for DALI V2 DALI XC DALI MC DALI basdim DGC DALI MSensor DALI TOUCHPANEL DALI PS2 Standby DALI-Somfy anmeo Interfae Table 8: Overvew of funton optons 8.1 DALI ontrol gear The onfguraton of the DALI ontrol gear s dvded nto: Bas onfguraton 45 n detal vew Trdon-spef onfguraton 50 n the ontext menu Deve-spef onfguraton n detal vew The masterconfigurator software an be used to onfgure the followng DALI ontrol gear elements: 40

41 Confguraton Deve Type 0 (DT 0): ontrol gear for fluoresent lamps 99 Deve Type 1 (DT 1): ontrol gear for emergeny lghtng 114 Deve Type 2 (DT 2): ontrol gear for hgh-pressure dsharge lamps Deve Type 3 (DT 3): ontrol gear for low-voltage halogen lamps Deve Type 4 (DT 4): ontrol gear for phase dmmers Deve Type 5 (DT 5): not supported Deve Type 6 (DT 6): ontrol gear for LEDs 143 Deve Type 7 (DT 7): ontrol gear for swthng funton Deve Type 8 (DT 8): ontrol gear for olour onverters Deve Type 255 (DT 255): mult-deve type Deve type unknown: The deve operatng mode s norretly set for ontrol gear whh s reported as Deve type unknown. Perform readdressng. The deve operatng mode of all deves onneted to the DALI ontrol lne s automatally set to automat deteton. -orgo to the Trdon-spef onfguraton ontext menu n the Deve operatng mode tab and hange the deve operatng mode to automat deteton. Confguraton usng group ommands Requrement for all the followng steps: Deves have been grouped. Desred group s seleted. Control gear an be onfgured n groups, f t has already been assgned to groups. 41

42 Confguraton Regroup ontrol gear 1. Enter the desred number n nput feld Group. 2. Clk Apply. All the ontrol gear of the seleted group are sent to the group. Test onfguraton of group At Quk test the onfguraton of the seleted group an be tested. 1. Clk desred term (Off, Maxmum level, Mnmum level, Brghten, Dm). Set DALI default parameters A group s defned by the values of the DALI default parameters Fade Tme, Fade Rate, Mnmum Level, Maxmum Level, Power On Level, System Falure Level. More nformaton about the DALI default parameters an be found at DALI default parameters Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. De Send key s hghlghted n olour whh ndates that the value hasn't been sent to the group yet. 2. Clk Send to send the set value to the group. The Send key hanges the olour bak to normal. 42

43 Confguraton Set senes A sene s defned by the values of the parameters Intensty and Colour temperature. Settng the Colour temperature s only possble for Gerätetyp 8: Betrebsgerät für Farbkonverter Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. De Send key s hghlghted n olour whh ndates that the value hasn't been sent to the group yet. 2. Clk Send to send the set value to the group. The Send key hanges the olour bak to normal. All the lumnares n ths group adopt the set value. Set to senes At Set to sene the sene settngs an be set to sene number (0-15). 1. Clk desred number to set settngs to a sene number. The text "Sene xx s set" s dsplayed. 43

44 Confguraton Deve nformaton Deve nformaton The followng deve nformaton s dsplayed n the header: Deve nformaton Desrpton Name Dsplays the name of the ontrol gear. Lght soure Dsplays the type of lght soure (LED, Fluoresent, HID ) onneted to the ontrol gear. Artle number Dsplays the artle number of the ontrol gear. Seral number Dsplays the unque seral number of the ontrol gear. Date of manufature Dsplays the date of manufature for the ontrol gear. Frmware verson Dsplays the frmware verson of the ontrol gear. DALI verson Dsplays the verson of the DALI spefaton supported by the ontrol gear. ed verson Dsplays the verson of the ed spefaton supported by the ontrol gear. ed s an enhaned protool based on DALI onnetons. Table 9: Deve nformaton 44

45 Confguraton Bas onfguraton The group assgnment for ontrol gear and senes and default DALI parameters an be set for eah ontrol gear element n the Bas onfguraton tab. Member of group(s) Member of group(s) spefes the group or groups to whh the ontrol gear belongs. These groups are ndated by the blue bakground. Wth these 16 keys the group membershp an be hanged easly. Senes The ntensty of the lumnare an be set for all 16 senes (0 15) here. Settng senes 1. Enable the hekbox for a sene, n order to assgn an ntensty to the lumnare. The nput feld an be edted. 2. Enter a value between 0.0 % and 100 % 3. To defne settngs for addtonal senes, repeat steps 1 and Clk on save. Changes are stored n the deve. MASK means that the lumnare n ths group wll retan ts urrent ntensty when the relevant sene s realled. The mnmum level and maxmum level for settng senes (default: 0.0 % and 100 %) an be hanged n the bas DALI onfguraton of the deve. When settng the sene value, the respetve DALI value s addtonally dsplayed n square brakets. Example: 100% [254] 45

46 Confguraton DALI default parameters DALI default parameters an be set here. DALI-Verson V1: DALI-Verson V2: Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clk on save. Changes are stored n the deve. When settng the DALI default parameters, the respetve DALI value s addtonally dsplayed n square brakets. Example: 100% [254] The followng DALI default parameters an be set: DALI default parameters Desrpton Fade tme The seleted value s set as the fade tme n seonds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The seleted value s set as the dmmng speed. It ndates by how many steps per seond the ntensty s hanged. The Fade Rate s used wth the DALI ommands Brghten (Up) and Dm 46

47 Confguraton (Down). Value range: steps per seond : 45 steps per seond s the DALI default. 358 steps per seond s the fastest fade rate, and 2.8 steps per seond s the slowest. Mnmum level The seleted value s set as the mnmum level for the ontrol gear. Ths value annot be fallen below durng dmmng/brghtenng. Value range: Physal lower lmt Maxmum level : The physal lower lmt of the ontrol gear s shown to the rght of the Mnmum level as a perentage. The mnmum level must be above ths value. Maxmum level The seleted value s set as the maxmum level for the ontrol gear. Ths value annot be exeeded durng dmmng/brghtenng. Value range: Mnmum Level 100% Power On Level The seleted value s set as the value after power s restored. Value range: 0 100% MASK System Falure Level The seleted value s set as the value n the event of falure of the DALI power supply. Value range: 0 100% MASK Extended Fade Tme (only DALI V2) By usng the hekbox the Power On Level an be ether fxed (hekbox atvated) or set to MASK (hekbox deatvated). When power s restored, the deve reats as follows: If the hekbox s atvated, the deve swthes to the fxed value. If the hekbox s deatvated (settng MASK), the deve swthes to the last atve ntensty. By usng the hekbox the System Falure Level an be ether fxed (hekbox atvated) or set to MASK (hekbox deatvated). When there s a falure of the DALI power supply, the deve reats as follows: If the hekbox s atvated, the deve swthes to the fxed value. If the hekbox s deatvated (settng MASK), the deve swthes to the last atve ntensty. The seleted value s set as the fade tme. Value range: fast 100 ms - 16 mn 47

48 Confguraton The Extended Fade Tme s only effetve f the "old" Fade Tme and the Fast Fade Tme (DT6) s set to 0. Table 10: DALI default parameters To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. When settng the DALI default parameters, the respetve DALI value s addtonally dsplayed n square brakets. Example: 100% [254] 48

49 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 11: DALI ontrol gear status nformaton 49

50 Confguraton Trdon-spef onfguraton Trdon-spef onfguraton ontans the followng parameters: Deve operatng mode DALI V1 52 Deve operatng mode DALI V2 56 Logal Unts Features Optal Balanng hronostep hronostep 2 71 LED temperature montorng I-Selet 75 General log Drver log Emergeny log ITM CLO and OTL 85 Power-up Fadng 89 Current onsumpton I-Selet protokoll ColourSWITCH ProportonSWITCH 94 Compatblty settngs Status Overvew of funtons 98 All Trdon-spef funtons and status nformaton an be found n the Trdon-spef onfguraton pop-up wndow. Not every ontrol gear element supports all funtons. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. Open the Trdon-spef onfguraton pop-up wndow 1. In the DALI deve tree dagram, rght-lk on the DALI ontrol gear to be onfgured. The ontext menu appears. 2. Selet Trdon-spef onfguraton n the ontext menu. The Trdon-spef onfguraton pop-up wndow opens. -or- 50

51 Confguraton Double-lk the DALI ontrol gear to be onfgured n the DALI deve tree dagram. The Trdon-spef onfguraton pop-up wndow opens. 51

52 Confguraton Deve operatng mode DALI V1 The deve operatng mode used by the ontrol gear n order to arry out ts funtons an be set here. Confgurng the Deve operatng mode 1. Selet desred Deve operatng mode n the dropdown lst. 2. Clk on save. Deve operatng mode Desrpton Automat deteton The ontrol gear detets the nomng sgnal and swthes automatally to the orrespondng deve operatng mode. The followng deve operatng modes are automatally deteted: DALI only DSI only swthdim only DALI and SMART DSI and SMART swthdim and SMART orrdorfunction DALI only The ontrol gear detets only DALI ommands. DSI only The ontrol gear detets only DSI ommands. swthdim only The lumnares onneted to the ontrol gear an only be smoothly adjusted usng manual momentary-aton swthes. The mans voltage s used as a ontrol sgnal. The ontrol gear nterprets the sgnal as ether a smooth adjustment or swth ommand dependng on how long the manual momentary-aton swth s pressed. 52

53 Confguraton SMART only The lumnares onneted to the ontrol gear an only be smoothly adjusted usng a SMART nterfae. DALI and SMART The ontrol gear detets only DALI ommands and the lumnares onneted to the ontrol gear an only be smoothly adjusted usng a SMART nterfae. DSI and SMART The ontrol gear detets only DSI ommands and the lumnares onneted to the ontrol gear an only be smoothly adjusted usng a SMART nterfae. swthdim and SMART The lumnares onneted to the ontrol gear an only be smoothly adjusted usng manual momentary-aton swthes or va the SMART nterfae. orrdorfunction Funton used to automatally adjust the llumnane n an area (e.g. underground ar park, underground walkways for pedestrans). When a moton sensor detets movement, the lghtng swthes to the presene value. When absene s deteted, the lghtng swthes to the absene value. Then the lghtng s swthed off or stays at the absene value (dependng on requrements and settngs). There are four types of orrdorfunction: orrdorfunction wth fade tme Adjustable parameters: A) Presene value B) Absene value 2) Run-on tme 3) Fade tme 4) Swth-off delay orrdorfunction wth fade-n tme Adjustable parameters: A) Presene value B) Absene value 1) Fade-n tme 2) Run-on tme 4) Swth-off delay orrdorfunction wth fade-n tme and fade tme Adjustable parameters: A) Presene value B) Absene value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swth-off delay 53

54 Confguraton orrdorfunction wthout fade-n tme and fade tme Adjustable parameters: A) Presene value B) Absene value 2) Run-on tme 4) Swth-off delay Table 12: Deve operatng modes DALI V1 The DALI and SMART, DSI and SMART and swthdim and SMART deve operatng modes are not supported by the ontrol gear for fluoresent lamps belongng to the xte II seres. 54

55 Confguraton orrdorfunction parameters The followng table gves a desrpton of the ndvdual parameters for the orrdorfunction: Confguraton opton Desrpton Presene value Value to whh the lumnare group swthes when presene s deteted n the room. Value range: 0 100% Absene value Level to whh the lumnare group swthes durng the swth-off delay. Value range: 0 100% Fade-n tme Tme requred to reah the presene value. Value range: fast s Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. The run-on tme an be onfgured on the moton sensor. Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Value range: fast s Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absene value untl further movement s deteted and the moton sensor swthes to the presene value. The lumnare group s never swthed off by the moton sensor. Table 13: Overvew of orrdorfunction parameters 55

56 Confguraton Deve operatng mode DALI V2 The deve operatng mode used by the ontrol gear n order to arry out ts funtons an be set here. Confgurng the Deve operatng mode 1. Enable the desred rado button. 2. Clk on save. Deve operatng mode Desrpton Automat deteton The ontrol gear detets the nomng sgnal and swthes automatally to the orrespondng deve operatng mode. The followng deve operatng modes are automatally deteted: DALI DSI swthdim ready2mans 1-10 V orrdorfunction 2 DALI The ontrol gear detets only DALI ommands. DSI The ontrol gear detets only DSI ommands. swthdim The lumnares onneted to the ontrol gear an only be smoothly adjusted usng manual momentary-aton swthes. The mans voltage s used as a ontrol sgnal. The ontrol gear nterprets the sgnal as ether a smooth adjustment or swth ommand dependng on how long the manual momentary-aton swth s pressed. 56

57 Confguraton ready2mans The ontrol gear detets only ready2mans ommands V The ontrol gear adjusts the brghtness aordng to the appled voltage at the 1-10 V termnal. orrdorfunction Funton used to automatally adjust the llumnane n an area (e.g. underground ar park, underground walkways for pedestrans). When a moton sensor detets movement, the lghtng swthes to the presene value. When absene s deteted, the lghtng swthes to the absene value. Then the lghtng s swthed off or stays at the absene value (dependng on requrements and settngs). orrdorfunction 2 has the followng parameters: Adjustable parameters: A) Presene value B) Absene value 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swth-off delay hronostep 2 Ths deve operatng mode an be parametrzed n the hronostep 2 tab. Table 14: Deve operatng modes DALI V2 The DALI and SMART, DSI and SMART and swthdim and SMART deve operatng modes are not supported by the ontrol gear for fluoresent lamps belongng to the xte II seres. orrdorfunction 2 parameters The followng table gves a desrpton of the ndvdual parameters for the orrdorfunction 2: Confguraton opton Desrpton Presene value Value to whh the lumnare group swthes when presene s deteted n the room. Value range: 0 100% Absene value Level to whh the lumnare group swthes durng the swth-off delay. Value range: 0 100% Fade-n tme Tme requred to reah the presene value. Value range: 57

58 Confguraton fast 0.1 s 160 mn Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. Value range: 0 s 40 mn 50 s Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Value range: fast 0.1 s 160 mn Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Value range: 0 s 40 mn 50 s never OFF: the lghtng remans at the absene value untl further movement s deteted and the moton sensor swthes to the presene value. The lumnare group s never swthed off by the moton sensor. Table 15: Overvew of orrdorfunction 2 parameters 58

59 Confguraton Logal Unts Here you an assgn the physal LED outputs to dfferent logal unts (DALI addresses). The settng optons dffer, dependng on whether t s a ontrol gear for LEDs or a ontrol gear for olour onverters. For a ontrol gear for LEDs the followng settngs are avalable: 1. Selet hekbox 2 logal unts (DALI addresses) to assgn all LED outputs to one DALI address -or2. Selet hekbox 4 logal unts (DALI addresses) to assgn the LED outputs to two DALI addresses, whh means that two LED outputs are assgned to one DALI address. The hanged onfguraton of the deve s dsplayed n the tree vew as follows: For a ontrol gear for olour onverters the followng settngs are avalable: 59

60 Confguraton 1. Selet hekbox 1 logal unts (DALI addresses) to assgn all outputs to one DALI address -or2. Selet hekbox 2 logal unts (DALI addresses) to assgn the outputs to two DALI addresses. The hanged onfguraton of the deve s dsplayed n the tree vew as follows: The Logal Unts funton s only avalable f t s supported by the deve. 60

61 Confguraton Features The behavour n DC mode, epower On Level and preheatng tme an be set for the ndvdual ontrol gear element n the Features tab. Behavour durng DC operaton The ontrol gear an be set to reall a fxed ontrol value (0 100%) durng DC operaton or behave as f t s stll n normal operaton (.e. an be smoothly adjusted or swthed on/off) here. Settng behavour durng DC operaton 1. Enter the release ode. The nput felds an be edted. 2. Selet Fxed ontrol value and enter the desred ontrol value. -orselet Normal operaton. 3. Clk on save. Changes are stored n the deve.. The release ode an be obtaned from your sales partner. The urrent status of ths funton an be seen n the Trdon-spef onfguraton pop-up wndow n the Status tab. epower On Level Here users an set whether the Power On Level (value after power has been restored) s overwrtten by an ed ommand. The epower On Level an be set to swth the ontrol gear to a fxed ontrol value (0 100 %) or reall the memory value after power has been restored followng a falure. The memory value s the last ontrol value to whh the ontrol gear was set before the power falure. 61

62 Confguraton Settng epower On Level 1. Enable the Enable epower On Level hekbox. The nput felds an be edted. 2. Selet Fxed ontrol value and enter the desred ontrol value. -orselet Memory value. 3. Clk on save. Changes are stored n the deve. Preheatng tme The ontrol gear an be set to gnore the preheatng tme and mmedately swth on. Ignorng the preheatng tme may shorten the lamp lfe. Dsablng the preheatng tme 1. Enable the no preheatng tme hekbox. 2. Clk on save. Changes are stored n the deve. Fade2Zero The ontrol gear an be set to use a fade tme when the ontrol gear s swthed off. Enable Fade2Zero 1. Enable the enable Fade2Zero hekbox. 62

63 Confguraton 2. Clk on save. Changes are stored n the deve. Physal mn level The ontrol gear an be set to use a physal mn level (PHM). The physal mn level s the lowest value the deve an reah. If an attempt s made to set a mnmum level that s lower than the physal mn level, the physal mn level s automatally adjusted to a hgher value. Set physal mn level 1. Enable the set physal mn level hekbox. 2. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 3. Clk on save. Changes are stored n the deve. Send physal mn level broadast 1. Enable the send broadast hekbox. 2. Clk on save. Changes are stored n all deves. 63

64 Confguraton Optal Balanng Here you an dvde the avalable output urrent between one or two outputs. The maxmum total urrent s 1 A. Dstrbutng output urrent to one output 1. Enable hekbox of one output. Slder beomes adjustable. 2. Use the slder to set a value between 170 and 700 ma. The value s shown to the left of the slder. 3. Clk on save. Changes are stored n the deve. 64

65 Confguraton Dvdng output urrent between two outputs 1. Enable hekboxes of outputs 1 and 2. Slders beome adjustable. 2. Use the slder to set a value between 170 and 700 ma for output 1. The value s shown to the left of the slder. 3. Use the slder to set a value between 170 and 700 ma for output 2. The value s shown to the left of the slder. The maxmum total urrent s 1 A. If the output urrent for one output s set suh that the maxmum total urrent s exeeded, the value at the other output wll be automatally redued. 4. Clk on save. Changes are stored n the deve. Usng predefned values for the output urrent dstrbuton 1. Clk on the button for a predefned output urrent dstrbuton. The values are shown to the left of the slders. 2. Clk on save. Changes are stored n the deve. 65

66 Confguraton hronostep Here you an onfgure the hronostep funton. The lumnare alulates a vrtual mdnght (VM) based on the lamp burnng hours of the last 3 days. On ths bass, tme wndows an be defned wthn whh the ntensty of the lumnare an be redued n one or two steps. 66

67 Confguraton Overvew of hronostep funton The followng fgure shows a summary of the ndvdual parameters. 1) Reduton tme (t2 VM) A) Intensty 1 2) Reduton tme (VM t3) B) Intensty 2 (only for profles 2 5) 3) Reduton tme (t1 VM) (only for profles 2 5) C) Intensty 3 4) Reduton tme (VM t4) (only for profles 2 5) t0 Swth-on tme t5 Swth-off tme VM vrtual mdnght The reduton tmes are desrbed here: Parameter Desrpton 1) Reduton tme (t2 VM) Tme wndow before vrtual mdnght, durng whh the lumnare assumes ntensty 3. 2) Reduton tme (VM t3) Tme wndow after vrtual mdnght, durng whh the lumnare assumes ntensty 3. 3) Reduton tme (t1 VM) Tme wndow before vrtual mdnght, durng whh the lumnare assumes ntensty 2. 4) Reduton tme (VM t4) Tme wndow after vrtual mdnght, durng whh the lumnare assumes ntensty 2. Table 16: Overvew of reduton tmes Confguraton Seletng profle for vrtual mdnght 1. Selet the desred Profle n the Vrtual mdnght dropdown lst. 2. Clk on save. Confgurng reduton tmes Underneath the hronostep mage there are eght dropdown lsts to onfgure the four reduton tmes. 1. Selet the desred Reduton tme. 67

68 Confguraton 2. Selet hours from frst dropdown lst. 3. Selet mnutes from seond dropdown lst. 4. Clk on save. Confgurng ntensty Underneath the hronostep mage there are three nput felds to onfgure the ntensty. 1. Enter the desred Intensty. 2. Clk on save. 68

69 Confguraton hronostep profles You an hoose between 6 profles. If the hronostep and orrdorfunction funtons are enabled at the same tme, ths may ause problems. Therefore hek the deve operatng mode (Deve operatng mode tab) and ensure that orrdorfunction s not seleted. Profle 0 (dsabled) The hronostep funton s dsabled. The ntensty of the lumnare s not redued. Profle 1 (default) The ntensty of the lumnare s redued n one step. Parameter Value range 1) Reduton tme (t2 VM) 0 10 h MASK: MASK means that the t2 tme wll be gnored. 2) Reduton tme (VM t3) 0 10 h MASK: MASK means that the t3 tme wll be gnored. A) Intensty 1 100% (annot be set) C) Intensty 3 50% (annot be set) Table 17: Profle 1 parameter (default) 69

70 Confguraton Profles 2 5 (user-defned) These 4 profles an be onfgured ndvdually by eah user. The ntensty of the lumnare s redued n two steps. Parameter 1) Reduton tme (t2 VM) Value range 0 10 h MASK: MASK means that the t2 tme wll be gnored. 2) Reduton tme (VM t3) The value must be smaller than the reduton tme (t1 VM) h MASK: MASK means that the t3 tme wll be gnored. The value must be smaller than the reduton tme (VM t4). 3) Reduton tme (t1 VM) 0 10 h MASK: MASK means that the t1 tme wll be gnored. 4) Reduton tme (VM t4) 0 10 h MASK: MASK means that the t4 tme wll be gnored. A) Intensty 1 100% (annot be set) B) Intensty 2 0%; 5 100% C) Intensty 3 Intensty 2 must be less than Intensty 1. 0%; 5 100% Intensty 3 must be less than Intensty 2. Table 18: Profle parameters 2 5 (user-defned) 70

71 Confguraton hronostep 2 Here you an onfgure the hronostep 2 funton. hronostep 2 s a further development of hronostep offers more profles and settngs. 66 and The hronostep 2 tab s only dsplayed f the deve operatng mode (Deve operatng mode tab) s set to hronostep 2. 71

72 Confguraton hronostep 2 profles You an hoose between 7 profles. 4 profles are pre-defned standard profles. The other 3 profles an be adjusted ndvdually. If the hronostep 2 and orrdorfunction funtons are enabled at the same tme, ths may ause problems. Therefore hek the deve operatng mode (Deve operatng mode tab) and ensure that orrdorfunction s not seleted. Confguraton The profles an be adjusted by settng the values for 8 dfferent reduton tmes. The tme an be set va two dropdown menus for hours and mnutes. The ntensty an be entered as a perentage value. Seletng profle for vrtual mdnght 1. Selet the desred Profle n the Vrtual mdnght dropdown lst. 2. Clk on save. Confgurng reduton tme and ntensty 1. Enable the hek box of the desred Red. tme (reduton tme). 2. Selet hours from frst dropdown lst. 3. Selet mnutes from seond dropdown lst. 4. Enter the desred perentage. 5. Clk on save. 72

73 Confguraton LED temperature montorng LED temperature montorng an be onfgured here. LED temperature montorng s ntended to protet the LED aganst thermal damage. Parameter Desrpton Temperature montorng Temperature montorng an be enabled or dsabled. Enablng or dsablng temperature montorng: 1. Selet enabled or dsabled n the Temperature montorng dropdown lst. 2. Clk on save. Temperature sensor Indates whether a temperature sensor s onneted. Temperature urrently measured at the LED Indates the temperature urrently measured at the LED. Swth-off temperature Indates the temperature at whh the ontrol gear for the LED s swthed off to protet the LED aganst thermal damage. Ths allows the LED to ool. The ontrol gear for the LED remans swthed off untl the temperature for restart s reahed. Value range: C Confgurng the swth-off temperature: 1. Enter the desred swth-off temperature. 2. Clk on save. 73

74 Confguraton Start power reduton at Indates the temperature at whh the LED output urrent s gradually redued. The LED s dmmed. Ths allows the LED to ool. The LED s dmmed untl the temperature has fallen by 5 C. Value range: Ths temperature s alulated automatally. It s 5 C below the swth-off temperature. Stop power reduton at If the temperature ontnues to nrease despte the power reduton, the ontrol gear for the LED s swthed off as soon as the swth-off temperature s reahed. Temperature at whh the reduton of the LED output urrent s stopped and the LED output urrent s gradually nreased agan. LED output urrent s gradually nreased untl the temperature reahes the start power reduton at parameter. Value range: Ths temperature s alulated automatally. It s 5 C below the temperature at whh the power reduton s started. Temperature for restart Indates the temperature at whh the LED output urrent s swthed bak on after a thermal shut down: The LED output urrent assumes the value before the Intellgent Temperature Management was atvated. Value range: Ths temperature s alulated automatally. It s 30 C below the swth-off temperature. Table 19: LED temperature montorng parameters 74

75 Confguraton I-Selet The eletr urrent used by the ontrol gear to supply the onneted LEDs an be onfgured here. Not every ontrol gear element supports ths funton. Whether ths funton s supported by the ontrol gear an be found on the data sheet for the ndvdual deve. Data sheets are avalable to downloaded onlne at Parameter Desrpton Output urrent Indates the eletr urrent used by the ontrol gear to supply the onneted LEDs. Maxmum output urrent Indates the maxmum onfgurable eletr urrent that an be used by the ontrol gear to supply the onneted LEDs. Mnmum output urrent Indates the mnmum onfgurable eletr urrent that an be used by the ontrol gear to supply the onneted LEDs. Table 20: Parameters for adjustable output urrent 75

76 Confguraton Confgurng the output urrent usng the masterconfigurator software 1. Enable the va software rado button. 2. Enter a value between the maxmum and mnmum output urrent n the nput feld. -orclk a button wth a predefned value. The value s dsplayed n the nput feld. 3. Clk on save. Changes are stored n the deve. The ontrol gear only regulates to the saved output urrent one the voltage supply to the ontrol gear s dsonneted and then reonneted agan. Confgurng the output urrent va the termnal on the ontrol gear 1. Dsonnet the voltage supply to the ontrol gear. 2. To set the mnmum output urrent, do not brdge the termnal on the ontrol gear. -orto set the maxmum output urrent, brdge the termnal on the ontrol gear. -orto set a value between the mnmum and maxmum output urrent, use a resstor. The types of resstors whh an be used an be found on the data sheet for the ndvdual deve. Data sheets are avalable to downloaded onlne at 3. Reonnet the voltage supply to the ontrol gear. 4. Enable the va termnal rado button. 5. Clk on save. Changes are stored n the deve. The ontrol gear only regulates to the saved output urrent one the voltage supply to the ontrol gear s dsonneted and then reonneted agan. 76

77 Confguraton General log General Parameter Desrpton Produton date Date of manufaturng. OEM GTIN Global Trade Item Number OEM ID Indates the deve dentfaton. Total operaton tme Indates the tme the deve was operated ether va mans or from battery. Table 21: Parameters for General Mans Parameter Desrpton Current onsumpton The Current onsumpton tab shows the atve urrent onsumpton. The value s updated every mnute. Mans overvoltage ounter Indates how often a voltage > 230 V was measured at the mans nput. Maxmum mans voltage Indated the maxmum voltage measured at the mans nput. Table 22: Parameters for Mans 77

78 Confguraton 78

79 Confguraton Drver log Drver Parameter Desrpton Frmware verson Indates the frmware verson of the emergeny drver. Hardware verson Indates the hardware verson of the emergeny drver. Produt verson Indates the produt verson of the emergeny drver. Deve restart ounter Indates how often the deve was restarted. Internal tmng errors ounter Indates how often the deve had to restart tself due to a tmng error. Software restart va DALI ounter Indates how often the deve was restarted va DALI. Crtal temperature reahed ounter Indates how often the deve reahed a rtal temperature and the Intellgent Temperature Guard funton (ITG) turned off the deve. Hgh temperature reahed ounter Indates how often the deve reahed a rtal temperature and the Intellgent Temperature Guard funton (ITG) started to dm t down. Mnmum gear temperature Indates the mnmum temperature the deve had reahed. Maxmum gear temperature Indates the maxmum temperature the deve had reahed. 79

80 Confguraton Table 23: Parameters for Drver LED Parameter Desrpton Mnmum output urrent Indates the mnmum onfgurable eletr urrent that an be used by the ontrol gear to supply the onneted LEDs. Maxmum output urrent Indates the maxmum onfgurable eletr urrent that an be used by the ontrol gear to supply the onneted LEDs. Used output urrent Indates the eletr urrent used by the ontrol gear to supply the onneted LEDs. LED swthng yle ounter Indates how often the LED was swthed on. LED undervoltage ounter Indates how often a LED wth a too low forward voltage was onneted. LED overvoltage ounter Indates how often a LED wth a too hgh forward voltage was onneted. LED overpower ounter Indates how often a LED wth a too hgh power was onneted. Open rut at LED output ounter Indates how often no LED was onneted. Short rut at LED output ounter Indates how often the LED output was short ruted. Table 24: Parameters for LED 80

81 Confguraton Emergeny log Emergeny Parameter Desrpton System falures ounter Indates how often the DALI nterfae was unpowered. The parameter s refreshed every. Internal rut falures ounter Indates a rtal nternal error n the emergeny lghtng ontrolgear. Total lamp burnng tme Indates how long the lamp was on n emergeny and mans mode. Lamp burnng mnutes are ndated n 1-mnute nrements. Lamp burnng tme n emergeny mode Indates how long the lamp was on n emergeny mode. Lamp burnng mnutes n emergeny mode are ndated n 1-mnute nrements. Lamp burnng tme n emergeny mode wth urrent battery Indates how long the lamp was on n emergeny mode wth the urrently onneted battery. Lamp burnng mnutes n emergeny mode wth urrent battery are ndated n 1-mnute nrements. Total operaton tme Indates how long the deve was powered ether by mans or battery. Table 25: Parameters for Emergeny Battery Parameter Desrpton 81

82 Confguraton Hgh temperature fault ounter Indates how often the battery temperature reahed a rtally hgh level. Hgh temperature warnng ounter Indates how often the battery temperature reahed a hgh level. Low temperature fault ounter Indates how often the battery temperature reahed a rtally low level. Low temperature warnng ounter Indates how often the battery temperature reahed a low level. Rest mode atvaton ounter Indates how often the deve entered rest mode. Emergeny mode ounter Indates how often the deve entered emergeny mode. Started funton test ounter Indates how often the deve started a funton test. Started duraton test ounter Indates how often the deve started a duraton test. Faled funton test ounter Indates how often a funton test faled. Faled duraton test ounter Indates how often a duraton test faled. Funton test delay exeeded ounter Indates how often a funton test was requested and ould not be arred out n the spefed tme. Duraton test delay exeeded ounter Indates how often a duraton test was requested and ould not be arred out n the spefed tme. Low voltage battery ut off ounter Indated how often the battery was dsharged to the low voltage battery ut off. Battery falure ounter Indates how often a battery falure was deteted. Average battery temperature Indates the average battery temperature. Battery replaement ounter Indates how often the battery was replaed aordng to the replaement proess mentoned n the datasheet. Operaton tme Indates how long the battery was onneted to the deve. Mnmum battery temperature Indates the mnmum battery temperature. Maxmum battery temperature Indates the maxmum battery temperature. Table 26: Parameters for Battery 82

83 Confguraton ITM LED temperature montorng an be onfgured here. LED temperature montorng s ntended to protet the LED aganst thermal damage. Parameter Desrpton Temperature sensor Indates whether a temperature sensor s onneted. Maxmum swth-off temperature Indates the maxmum onfgurable swth-off temperature. Mnmum swth-off temperature Indates the mnmum onfgurable swth-off temperature. Swth-off temperature Indates the temperature at whh the ontrol gear for the LED s swthed off to protet the LED aganst thermal damage. Ths allows the LED to ool. The ontrol gear for the LED remans swthed off untl the temperature for restart s reahed. Value range: mnmum swth-off temperature maxmum swth-off temperature Confgurng the swth-off temperature: 1. Enter the desred swth-off temperature. 2. Clk on save. 83

84 Confguraton Start power reduton at Indates the temperature at whh the LED output urrent s gradually redued. The LED s dmmed. Ths allows the LED to ool. The LED s gradually dmmed untl the temperature redues by 10%, or 50% of the urrent ntensty has been reahed. Value range: Ths temperature s alulated automatally. The value s 15% below the swth-off temperature. Stop power reduton at If the temperature ontnues to nrease despte the power reduton, the ontrol gear for the LED s swthed off as soon as the swth-off temperature s reahed. Temperature at whh the reduton of the LED output urrent s stopped and the LED output urrent s gradually nreased agan. LED output urrent s gradually nreased untl the temperature reahes the start power reduton at parameter. Value range: Ths temperature s alulated automatally. Value s 10% below the temperature at whh the power reduton starts. Temperature for restart Indates the temperature at whh the LED output urrent s swthed bak on after a thermal shut down: The LED output urrent assumes the value before the Intellgent Temperature Management was atvated. Value range: Ths temperature s alulated automatally. The value s 50 % below the swth-off temperature. Dsable ITM Va the hekbox Dsable ITM the ITM funton an be dsabled. Dsable ITM an be used to replae the temperature sensor wth a new one or to deatvate the ITM funton permanently. After the replaement of the temperature sensor the new sensor s automatally deteted and 10 mnutes later the ITM funton s automatally re-enabled. In order to permanently deatvate the ITM funton the temperature sensor must be removed. Dsablng ITM 1. Enable the Dsable ITM hekbox. 2. Clk on save. Table 27: Parameters for LED temperature montorng 84

85 Confguraton CLO and OTL The CLO and OTL funtons an be onfgured here. CLO The CLO funton s a ontrol to ensure that the requred ntensty remans onstant over the entre LED lamp lfe. CLO dsabled Requred ntensty: 100% Expeted LED lfe: 50,000 h The ntensty of an LED ontnuously dereases over the LED lamp lfe. The ontrol gear does not ompensate for ths derease. For ths reason the requred ntensty an no longer be ensured over the entrety of the LED's lamp lfe. CLO enabled Requred ntensty: 80% Expeted LED lfe: 50,000 h A requred ntensty must be defned n order to ensure a onstant ntensty over the LED lamp lfe. Ths ntensty s based on the natural reduton of ntensty defned by the LED manufaturer. The ontrol gear ompensated for ths natural reduton by adjustng ts own output aordngly. Table 28: Dfferene betw een enabled and dsabled CLO funton OTL If the OTL funton s enabled, vsual feedbak s gven as soon as the LED exeeds the expeted LED lamp lfe. If the expeted LED lamp lfe s exeeded, the lumnare flashes for 2 seonds after beng swthed on. 85

86 Confguraton Parameter Desrpton Constant ntensty (CLO) The CLO funton an be enabled or dsabled. Enablng or dsablng CLO: 1. Selet enabled or dsabled n the Constant ntensty dropdown lst. 2. Clk on save. Vsual feedbak (OTL) The OTL funton an be enabled or dsabled. Enablng or dsablng OTL: 1. Selet enabled or dsabled n the Vsual feedbak dropdown lst. 2. Clk on save. Power of the ontrol gear Indates the urrent ontrol gear output requred for reahng the requred ntensty. Requred ntensty Indates the ntensty whh should reman onstant over the entrety of the LED lamp lfe. Value range: % If only the OTL funton s enabled, the Requred ntensty annot be onfgured. It wll be set at 100%. 86

87 Confguraton Confgurng requred ntensty 1. Enter the desred Requred ntensty. 2. Clk on save. LED burnng hours Indates the duraton for whh the LED has been on. If the Advaned settngs are enabled, the LED burnng hours an be onfgured. Informaton on how to enable the Advaned settngs an be found n Seton Atve wndow 12. Confgurng LED burnng hours 1. Enter the desred LED burnng hours. 2. Clk on save. Expeted LED lfe Indates the duraton for whh the LED an be operated before t beomes unusable or no longer meets the rtera gven n applable standards. Value range: 0 127,500 h The Expeted LED lfe s onfgured n 500-hour nrements. Table 29: Parameters for CLO and OTL funtons If faulty ontrol gear for LEDs must be replaed, we reommend applyng the settngs from another ontrol gear element for LEDs to the new ontrol gear element for LEDs. Applyng settngs from another ontrol gear element for LEDs Requrements: Advaned settngs are enabled. Old ontrol gear for LEDs has been replaed by new ontrol gear for LEDs. 1. Dsplay the nformaton for a ontrol gear element for LEDs loated n the same room as the new ontrol gear element for LEDs. 2. Open the Trdon-spef onfguraton pop-up wndow. 3. Clk the CLO and OTL tab. 4. Make a note of the values for the followng parameters: Requred ntensty, LED burnng hours and Expeted LED lfe. 5. Close the Trdon-spef onfguraton pop-up wndow. 6. Dsplay the nformaton for the new ontrol gear element for LEDs. 7. Open the Trdon-spef onfguraton pop-up wndow. 8. Clk the CLO and OTL tab. 9. Enter the values prevously noted from the other ontrol gear element for the followng parameters: Requred ntensty, LED burnng hours and Expeted LED lfe. 87

88 Confguraton 10.Clk on save. Changes are stored n the deve. 88

89 Confguraton Power-up Fadng The tme t takes after lghtng s swthed on for t to reah the value set for when power s restored (Power On Level or epower On Level) an be onfgured here. The Power-up Fadng funton s only avalable when the lghtng s swthed on va the supply voltage or swthdim. Value range: 0 16 s, where 0 s s the fastest tme and 16 s the longest. The Power-up Fadng funton does not affet the fade tme, as these are two dfferent funtons. For a detaled desrpton of the fade tme, see Seton Deve type 6: ontrol gear for LEDs > Bas onfguraton 46. Confgurng Power-up Fadng for the Power On Level Requrement: epower On Level funton s dsabled. 1. Selet the tme for Power-up Fadng n the dropdown lst. 2. Clk on save. Changes are stored n the deve. The value for the Power On Level an be hanged n the Bas onfguraton detal vew n the DALI default parameters group box. For a detaled desrpton of the Power On Level, see Seton Deve type 6: ontrol gear for LEDs > Bas onfguraton

90 Confguraton Confgurng Power-up Fadng for the epower On Level Requrements: Control gear supports the epower On Level funton. epower On Level funton s enabled. 1. Selet the tme for Power-up Fadng n the dropdown lst. 2. Clk on save. Changes are stored n the deve. The value for the epower On Level an be hanged n the Trdon-spef onfguraton pop-up wndow n the Features tab. For a detaled desrpton of the epower On Level, see Seton Features

91 Confguraton Current onsumpton The Current onsumpton tab shows the atve orrent onsumpton. The value s updated every mnute. 91

92 Confguraton I-Selet protokoll The I-Selet Protool tab shows the last 5 values and the maxmum of I-Selet. The tab dsplays the output urrent, the duraton and how the urrent was set (va Memory Bank, ready2mans or a resstor). 92

93 Confguraton ColourSWITCH Here you an set dfferent olour temperatures for ten senes. Defne Colour temperature for a sene 1. Enable the hekbox for a sene, n order to assgn a olour temperature to the lumnare. The nput feld an be edted. 2. Clk the button. The Set sene pop-up wndow appears. 3. Set the value for the olour temperature usng the slder. -orclk a button wth a predefned value. 4. Clk Okay. The vew s updated. 5. Clk on save. Changes are stored n the deve. 93

94 Confguraton ProportonSWITCH Here you an set dfferent ntenstes for ten senes. Defne ntensty for a sene 1. Enable the hekbox for a sene, n order to assgn an ntensty to the lumnare. The nput feld an be edted. 2. Enter a value between 0% and 100%. 3. To defne the settngs for the other senes, repeat steps 2 to 5 for eah sene. 4. Clk on save. Changes are stored n the deve. 94

95 Confguraton Compatblty settngs The generaton wth whh the ontrol gear s ompatble an be set here. Dependng on the ompatblty settngs supported by the ontrol gear, the followng optons are avalable: urrent generaton (n): the ontrol gear uses the settngs for the urrent generaton. preedng generaton (n-1): the ontrol gear uses the settngs for the preedng generaton (n-1). pre-preedng generaton (n-2): the ontrol gear uses the settngs for the generaton before last (n-2). A detaled desrpton of whh parameters are hanged (e.g. Mnmum level, Fade tme), an be found n the produt doumentaton for the orrespondng ontrol gear. Seletng ompatblty settngs 1. Selet the ompatblty settng n the dropdown lst. 2. Clk on save. Changes are stored n the deve. The urrent status of ths funton an be seen n the Trdon-spef onfguraton pop-up wndow n the Status tab. 95

96 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. Status Desrpton Normal operaton durng DC operaton Indates whether the ontrol gear ontnues n normal operaton durng DC operaton,.e. an be smoothly adjusted and swthed on/off. Compatblty Indates the ompatblty settng used by the ontrol gear. Intellgent Temperature Guard (ITG) Indates whether the Intellgent Temperature Guard s enabled or dsabled. Ambent lght ontrol Indates whether the ambent lght ontrol s enabled or dsabled. Supply voltage Indates the supply voltage wth whh the ontrol gear s operatng. Overvoltage Indates whether the Intellgent Voltage Guard (IVG) has deteted an overvoltage. When overvoltage s deteted, the lamps onneted to the ontrol gear flash n alternatng suesson. Undervoltage Indates whether the Intellgent Voltage Guard (IVG) has deteted an undervoltage. When voltage under 70 V s deteted, the lamps onneted to the ontrol gear swth off. When voltage between 70 and 140 V s deteted, the lamps onneted to the ontrol gear swth on and off at rregular ntervals. 96

97 Confguraton SMART sensor onneted Indates whether a SMART sensor s onneted and that no error has ourred. Yes: SMART sensor onneted and no error No: no SMART sensor onneted, or SMART sensor onneted but error has ourred Slave mode atve Indates whether the slave mode s enabled. In slave mode the sensor s onneted to two deves smultaneously and annot be onfgured. The sensor only responds to ommands from the master deve. LED temperature montorng (ITM) atve Indates whether the LED temperature montorng (ITM) funton s enabled. ITM fault Indates whether a short rut has ourred for the temperature sensor used for LED temperature montorng (ITM). Automat physal mnmum level deteton Indates whether the automat physal mnmum level deteton s enabled (default). The automat physal mnmum level s enabled for as long as no physal mnmum level has been set (see Seton Features) Lamp burnng hours Indates the duraton for whh the lamp has been on. Table 30: Status nformaton 97

98 Confguraton Overvew of funtons The Overvew of funtons tab shows all funtons supported by ontrol gear of ths deve type. The Overvew of funtons tab s only vsble f advaned settngs have been enabled. Not every ontrol gear element supports all funtons. For ths reason the funtons are shown wth the followng symbols: Ths funton s supported by the ontrol gear. Ths funton s not supported by the ontrol gear. Types of funtons The followng types of funtons are avalable: Confgurable funtons Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Funtons wth dsplayed statuses Ths funtons annot be onfgured. Statuses are shown n the Status tab. Confgurable funtons wth dsplayed statuses Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Statuses are shown n the Status tab. 98

99 Confguraton Deve Type 0: Control gear for fluoresent lamps Control gear for fluoresent lamps are shown n the DALI deve tree dagram wth the desrpton fluoresent. symbol and the short Speal features: xte II Varous SMART sensors and SMART plugs an be onneted to ontrol gear for fluoresent lamps from seres xte II va a SMART nterfae. More nformaton on possble ombnatons of ndvdual xte II ontrol gear elements and SMART sensors/plugs an be found n the deve doumentaton. Dfferent tabs (and thus dfferent ombnaton optons) are dsplayed n the masterconfigurator dependng on whh SMART sensor/plug s onneted. The tabs shown for spef sensors or plugs are gven n the followng table: Deve name Lght sensor Moton sensor Remote ontrol Plug SMART Sensor 5D x SMART Sensor 5DP x x SMART Sensor 5DPI x x x SMART Sensor 5DPI F NO x x x x SMART Sensor 5DPI F 01 x x x x SMART Sensor 5DPI F 30 x x x x SMART Sensor 10DPI x x x SMART Sensor 10DPI F NO x x x x SMART Sensor 10DPI F 01 x x x x SMART Sensor 10DPI F 30 x x x x SMART Plug MA x SMART Plug F NO x SMART Plug F 01 x SMART Plug F 30 x SMART Plug GrA x SMART Plug GrB x SMART Plug GrC x SMART Plug GrD x 99

100 Confguraton Table 31: Overvew of SMART sensors and SMART plugs For further detals on ndvdual SMART sensors and SMART plugs, please refer to the relevant deve doumentaton. Lght sensor SMART deve nformaton The followng deve nformaton s dsplayed: Deve nformaton Desrpton Name Dsplays the name of the SMART sensor. Artle number Dsplays the artle number of the SMART sensor. Hardware verson Dsplays the hardware verson of the SMART sensor. Software verson Dsplays the software verson of the SMART sensor. Table 32: SMART deve nformaton Status The followng status nformaton s dsplayed for the lght sensor: Status Desrpton Illumnane Illumnane urrently measured at the lght sensor. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. 100

101 Confguraton Update status automatally Indates whether the lght sensor status s updated automatally. Ambent lght ontrol Indates the status of ambent lght ontrol for the lght sensor. enabled: ambent lght ontrol s enabled. dsabled: ambent lght ontrol s dsabled. started: ambent lght ontrol has been started. The lght sensor regulates the ontrol gear to math the desred value. Table 33: Status nformaton Confguraton optons The followng onfguraton optons are dsplayed for the lght sensor: Confguraton opton Desrpton Ambent lght ontrol Ambent lght ontrol an be enabled or dsabled. Automat ontrol Indates the sene wth whh the ambent lght ontrol s enabled. When ths sene s realled, the sensor s enabled, the lumnares are swthed on and ambent lght ontrol regulates the lumnares. : The sene seleted here s dentfed n the Bas onfguraton as automat. Enable dmmng off (brght out) Chekbox enabled: f the measured llumnane exeeds the desred value by 150% for longer than 8.5 mnutes, the lumnare group wll be swthed off by the lght sensor even f movement s deteted n the room. As soon as the measured llumnane falls below the desred value, the lumnare group s swthed on agan. Set desred value Set the desred value for ambent lght ontrol. The desred value s the value to whh the lght sensor regulates the ontrol gear. The default settng s 500 lx. Ths value an be smoothly adjusted usng the Dm and Brghten ommands untl the desred llumnane s aheved. Use a luxmeter to aheve an aurate measurement of the llumnane. Table 34: Lght sensor onfguraton optons 101

102 Confguraton Automat ontrol for dfferent SMART sensors and SMART plugs The automat ontrol for the SMART Sensor 5D refers only to ambent lght ontrol. In ontrast, the automat ontrol for sensors SMART Sensor 5DP, SMART Sensor 5DPI and SMART Sensor 10DPI refers to a type of ambent lght ontrol that depends on the presene of people. More nformaton an be found n Seton Moton sensor To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. Moton sensor SMART deve nformaton The followng deve nformaton s dsplayed: Deve nformaton Desrpton Name Dsplays the name of the SMART sensor. 102

103 Confguraton Artle number Dsplays the artle number of the SMART sensor. Hardware verson Dsplays the hardware verson of the SMART sensor. Software verson Dsplays the software verson of the SMART sensor. Table 35: SMART deve nformaton Status The followng status nformaton s dsplayed for the moton sensor: Status Desrpton Update status automatally Indates whether the moton sensor status s updated automatally. Moton sensor Indates the status of the moton sensor: Movement deteted No movement deteted Table 36: Status nformaton Confguraton optons The followng onfguraton optons are dsplayed for the moton sensor: Confguraton opton Desrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatally swthed on and off dependng on whether presene s deteted. (fatory settng) enabled (only OFF): the moton sensor swthes the lghtng off only. It must be swthed on manually. dsabled: the moton sensor s dsabled. The lghtng must be swthed on and off manually. : The never OFF funton s mplemented as follows: 1. Selet the enabled operatng mode. 2. Selet swth-off delay never OFF. Automat ontrol Indates the sene used to ontrol the lghtng based on whether presene s deteted. If ths sene s realled the moton sensor s enabled and the lumnares are ontrolled based on whether presene s deteted. : The sene seleted here s dentfed n the Bas onfguraton as automat. Table 37: Moton sensor onfguraton optons 103

104 Confguraton Automat ontrol for dfferent SMART sensors and SMART plugs The automat ontrol for sensors SMART Sensor 5DP, SMART Sensor 5DPI and SMART Sensor 10DPI refers to a type of ambent lght ontrol that depends on the presene of people. Ambent lght ontrol an be dsabled as follows: 1. Clk on the SMART lght sensor tab. 2. Selet dsabled for ambent lght ontrol. 3. Clk on save. Changes are stored n the deve. The moton sensor ontrols the lghtng based on the presene of people. orrdorfunction profles The orrdorfunction s a funton used to automatally adjust the llumnane n an area (e.g. underground ar park, underground walkways for pedestrans). When a moton sensor detets presene, the lghtng swthes to the presene value. When absene s deteted, the lghtng swthes to the absene value. Then the lghtng s swthed off or stays at the absene value (dependng on requrements and settngs). If the Operatng mode for the moton sensor s enabled, the user has fve profles from whh to hoose. Profle Desrpton never off The orrdorfunction parameters annot be onfgured, wth the exepton of the dead tme. The followng values are saved n the profle: A) Presene value: 100% B) Absene value: 10% 1) Fade-n tme: < 0.7 s 2) Run-on tme: 20 mn 3) Fade tme: 32 s 4) Swth-off delay: No swth-off delay s defned for ths profle. One the fade tme has expred, the absene value of 10% s mantaned untl the moton sensor one agan detets presene. Dead tme Swth-off delay: 1 mn The orrdorfunction parameters annot be onfgured, wth the exepton of the dead tme. The followng values are saved n the profle: A) Presene value: 100% B) Absene value: 10% 1) Fade-n tme: < 0.7 s 2) Run-on tme: 20 mn 3) Fade tme: 32 s 4) Swth-off delay: 1 mn Dead tme Swth-off delay: 30 mn The orrdorfunction parameters annot be onfgured, wth the exepton of the dead tme. The followng values are saved n the profle: A) Presene value: 100% B) Absene value: 10% 1) Fade-n tme: < 0.7 s 2) Run-on tme: 20 mn 3) Fade tme: 32 s 4) Swth-off delay: 30 mn Dead tme 104

105 Confguraton user-defned 1 The orrdorfunction parameters an be freely onfgured, wth the exepton of the fade-n tme. A) Presene value B) Absene value 1) Fade-n tme: < 0.7 s (not onfgurable) 2) Run-on tme 3) Fade tme 4) Swth-off delay Dead tme user-defned 2 The orrdorfunction parameters an be freely onfgured, wth the exepton of the fade-n tme. A) Presene value B) Absene value 1) Fade-n tme: < 0.7 s (not onfgurable) 2) Run-on tme 3) Fade tme 4) Swth-off delay Dead tme Table 38: orrdorfunction onfguraton optons Overvew of onfguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swth-off delay A) Presene value B) Absene value 105

106 Confguraton orrdorfunction parameters The followng table gves a desrpton of the ndvdual parameters for the orrdorfunction: Confguraton opton Desrpton Presene value Value to whh the lumnare group swthes when presene s deteted n the room. Absene value Level to whh the lumnare group swthes durng the swth-off delay. Fade-n tme Tme requred to reah the presene value. Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Dead tme Tme started by manually swthng off the lghtng va the momentaryaton swth or the remote ontrol and durng whh the moton sensor s dsabled. If movement s deteted n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s deteted n the room, the moton sensor s enabled agan. Table 39: Overvew of orrdorfunction parameters 106

107 Confguraton Remote ontrol 107

108 Confguraton SMART deve nformaton The followng deve nformaton s dsplayed: Deve nformaton Desrpton Name Dsplays the name of the SMART sensor. Artle number Dsplays the artle number of the SMART sensor. Hardware verson Dsplays the hardware verson of the SMART sensor. Software verson Dsplays the software verson of the SMART sensor. Table 40: SMART deve nformaton Confguraton optons The followng onfguraton optons are dsplayed for the remote ontrol: Confguraton opton Desrpton Remote ontrol Remote ontrol an be enabled or dsabled. : Only the SMART remote ontrol an be used wth ontrol gear from seres xte II. The key assgnment has already been parametersed. ON: the maxmum level s realled mmedately wthout any fade tme. OFF: the lumnares are swthed off mmedately wthout any fade tme. UP: the ntensty s nreased by the steps defned n the fade rate. DOWN: the ntensty s redued by the steps defned n the fade rate. SET: the urrent ntensty s saved as the desred value for ambent lght ontrol. AUTOMATIC: automat ontrol s enabled. Table 41: Remote ontrol onfguraton optons To apply the hanged values, lk on save. 108

109 Confguraton Plug SMART deve nformaton The followng deve nformaton s dsplayed: Deve nformaton Desrpton Name Dsplays the name of the SMART plug. Artle number Dsplays the artle number of the SMART plug. Hardware verson Dsplays the hardware verson of the SMART plug. Software verson Dsplays the software verson of the SMART plug. Table 42: SMART deve nformaton Confguraton optons The followng onfguraton optons are dsplayed for the plug: Confguraton opton Desrpton Plug Plug an be enabled or dsabled. Table 43: Plug onfguraton optons To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 109

110 Confguraton Speal feature: group plugs Group plugs automatally assgn the DALI ontrol gear element, nto whh they are plugged, to a group. Plug Effetve range SMART Plug GrA Group 0 SMART Plug GrB Group 1 SMART Plug GrC Group 2 SMART Plug GrD Group 3 Table 44: Group plugs and ther orrespondng effetve ranges A group plug that has been plugged n an be reonfgured ndvdually. It an be assgned to another group or to more than one group. If a reonfgured group plug s plugged nto another DALI ontrol gear element, ths element takes on the onfguraton of the group plug the next tme the power s reset. Changng the group to whh a group plug belongs Requrement: Group plug s plugged nto a DALI ontrol gear element. 1. In the DALI deve tree dagram, lk on the deve nto whh the group plug has been plugged. 2. Hold down the left mouse button. 3. Drag the deve to the desred group. (Drag & Drop) The deve s removed from the group n whh t was prevously loated and s added to the desred group. The group has now been hanged on the group plug. Assgnng a group plug to more than one group Requrement: Group plug s plugged nto a DALI ontrol gear element. 1. In the DALI deve tree dagram, lk on the deve nto whh the group plug has been plugged. 2. Hold down the left mouse button. 3. In addton, hold down the CTRL key. 4. Drag the deve to the desred group. The deve s oped. It s now n both groups. The group has been saved addtonally on the group plug. The group plug s now assgned to both groups. Deletng a group from a group plug Requrement: Group plug s plugged nto a DALI ontrol gear element. 1. Rght-lk on the deve nto whh the group plug has been plugged. The ontext menu appears. 2. Selet Remove deve from group n the ontext menu. 110

111 Confguraton The deve s removed from the group and appears one agan n the DALI deve tree dagram wthout a group. The group has now been deleted on the group plug. 111

112 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 45: DALI ontrol gear status nformaton 112

113 Confguraton SMART sensor status Status Desrpton Sensor onneted Indates whether a sensor s onneted. Sensor defeny Indates whether the sensor s experenng a defeny. Ambent lght ontrol Indates the status of ambent lght ontrol for the lght sensor. enabled: ambent lght ontrol s enabled. dsabled: ambent lght ontrol s dsabled. started: ambent lght ontrol has been started. The lght sensor regulates the ontrol gear to math the desred value. Moton sensor enabled Indates whether the moton sensor s enabled. Movement deteted Indates whether the moton sensor has deteted movement. Slave mode atve Indates whether the slave mode s enabled. The sensor annot be onfgured n slave mode. The sensor only responds to ommands from the master deve. Plug defeny Indates whether there s a fault wth the plug or the wrong plug s onneted. Ths status nformaton s only dsplayed when a SMART plug s plugged n. Table 46: Sensor status nformaton 113

114 Confguraton Deve Type 1: Control gear for emergeny lghtng Control gear for emergeny lghtng are shown n the DALI deve tree dagram wth the desrpton Emergeny lghtng. on and the short A dstnton s made between three types of swthng modes n the ase of emergeny lghtng: Non-mantaned lght The emergeny lghtng s swthed off n mans operaton, the emergeny lghtng s swthed on n emergeny mode (f there s a power falure or durng emergeny lghtng testng). Mantaned lght The lghtng s permanently swthed on durng both mans operaton and emergeny mode (e.g. esape sgn lumnares). In mans operaton the lghtng s suppled from the mans, n emergeny mode the lghtng s suppled by the battery. Swthed mantaned lght The lghtng s permanently swthed on durng both mans operaton and emergeny mode (e.g. esape sgn lumnares). In mans operaton the lghtng s suppled from the mans, n emergeny mode the lghtng s suppled by the battery. In mans operatons the lghtng an be swthed on and off and an be dmmed. 114

115 Confguraton Deve-spef onfguraton On the Emergeny lghtng tab, you an make the followng settngs for deve-spef onfguratons: Identfy emergeny lumnare For a detaled desrpton, see Seton Identfaton 116. Set the tme for emergeny mode after mans power s restored For a detaled desrpton, see Seton Emergeny mode after mans power s restored Confgure test settngs For a detaled desrpton, see Seton Test settngs Dsable emergeny lumnare through addtonal operatng modes For a detaled desrpton, see Seton Dsablng emergeny lumnares 123. Defne ntensty settngs n emergeny mode For a detaled desrpton, see Seton Intensty settngs n emergeny mode

116 Confguraton Identfaton Here you an dretly dsplay the address of the emergeny lumnare va the status LED on the deve. For ths purpose, the address s onverted nto a sx-dgt bnary number, whh s represented as a flashng pattern. The red LED stands for bnary number 0, the green LED for bnary number 1. The followng optons are avalable to users n order to onvert a bnary number to a demal number: EM PRO Ident.TOOL software: You an download ths software from Trdon's homepage at: Serves Software. EM PRO addressng tool (Artle number ) In the masterconfigurator software there are 3 ways n whh emergeny lumnares an be dentfed. Funton Desrpton Identfy emergeny lumnare button The address of an emergeny lumnare that s hghlghted n the deve tree dagram s dsplayed one or n an endless loop Enabled n the detal vew by lkng the Identfy emergeny lumnare button Loate on For a detaled desrpton of ths funton, see ths seton. The address of an emergeny lumnare that s hghlghted n the deve tree dagram s dsplayed n an endless loop Is enabled by lkng the Loate Identfy on on For a detaled desrpton of ths funton, see Seton Chekng deve assgnment The addresses of all the emergeny lumnares onneted to the DALI ontrol lne are dsplayed n an endless loop s enabled by lkng the Identfy on For a detaled desrpton of ths funton, see Seton Chekng deve assgnment Table 47: Summary of dentfyng emergeny lumnares 116

117 Confguraton Identfy emergeny lumnare one Clk the Identfy emergeny lumnare button. The emergeny lumnare's status LED sends the address of the emergeny lumnare one as a bnary flashng pattern. Identfy emergeny lumnare agan 1. Enable the Repeat dentfaton hekbox Clk the Identfy emergeny lumnare button. The emergeny lumnare's status LED sends the address of the emergeny lumnare n an endless loop as a bnary flashng pattern. 4. To qut dentfaton, dsable the Repeat dentfaton hekbox. The urrent status of ths funton an be seen n the Status tab. Emergeny mode after mans power s restored Here you an set how long emergeny mode s mantaned after mans power s restored. Ths funton s used, for example, to ompensate for voltage flutuatons after a power outage or to brdge the restrke tmes of hgh-pressure dsharge lamps. The battery must be suffently harged n order to mantan emergeny mode after mans power s restored. Set the tme for emergeny mode after mans power s restored 1. Selet a value n the dropdown lst. 2. Clk on save. Changes are stored n the deve. 117

118 Confguraton Test settngs Here you an vew the urrent onfguraton of the funton and duraton tests, onfgure the funton and duraton tests and defne a test wndow wthn whh the ontrol gear s to perform a test. Funton test Durng a funton test, a power falure s smulated n order to test whether the emergeny lumnare s funtonng properly. Confguraton opton Desrpton Number of hours untl the next test starts Indates n how many hours the next funton test wll be performed. Interval Indates at what ntervals the funton test s performed. The nterval for the funton test s spefed n days. Confgure Button used to onfgure funton test. Start Button used to start funton test manually. A manual funton test must be performed after nstallng and addressng the emergeny lumnare. Stop The ontrol gear usually performs a funton test mmedately. It s only delayed f the emergeny lumnare s n emergeny mode or f the battery s not suffently harged. To see whether the funton test has been started, vew the Status Operatng mode Funton test n progress tab. To see whether the funton test has been delayed, vew the Status Emergeny lghtng status Funton test on hold tab. Button used to termnate a funton test that s n progress prematurely. Table 48: Funton test onfguraton optons 118

119 Confguraton Confgure funton test 1. In the Funton test group feld, lk the Confgure button. The Confgure funton test pop-up wndow appears. 2. In the dropdown lst, selet an Interval wthn whh the test s to be performed. 3. In the dropdown lst, selet a Tme at whh the test s to be performed. 4. Choose a start date for the funton test n the alendar. The urrent day s marked n blue on the alendar. 5. Clk OK. Funton test has been onfgured. Settngs are transferred to the detal vew. 6. Clk on save. Changes are stored n the deve. 119

120 Confguraton Duraton test Durng a duraton test, a power falure s smulated n order to test whether the emergeny lumnare s funtonng properly and whether the battery aheves ts nomnal operatng duraton. Confguraton opton Desrpton Number of hours untl the next test starts Indates n how many hours the next duraton test wll be performed. Interval Indates at what ntervals the duraton test s performed. The nterval for the duraton test s spefed n weeks. Confgure Ths button s used to onfgure the duraton test. Start Button used to start duraton test manually. A manual duraton test must be performed after nstallng and addressng the emergeny lumnare. Stop The ontrol gear usually performs a duraton test mmedately. It s only delayed f the emergeny lumnare s n emergeny mode or f the battery s not fully harged. To see whether the duraton test has been started, vew the Status Operatng mode Duraton test n progress tab. To see whether the funton test has been delayed, vew the Status Emergeny lghtng status Funton test on hold tab. Button used to termnate a duraton test that s n progress prematurely. Table 49: Duraton test onfguraton optons 120

121 Confguraton Confgure duraton test 1. In the Duraton test group feld, lk the Confgure button. The Confgure duraton test pop-up wndow appears. 2. In the dropdown lst, selet an Interval wthn whh the test s to be performed. 3. In the dropdown lst, selet a Tme at whh the test s to be performed. 4. Choose a start date for the duraton test n the alendar. The urrent day s marked n blue on the alendar. 5. Clk OK. Duraton test has been onfgured. Settngs are transferred to the detal vew. 6. Clk on save. Changes are stored n the deve. 121

122 Confguraton Test wndow The test wndow defnes the maxmum tme that may elapse between the sheduled start tme and the tme the test s atually performed. The test wndow must be at least 24 hours beause the batteres an take up to 24 hours to fully harge when they are frst harged. Dfferent requrements apply n order to start a funton test and a duraton test. Test Requrement Funton test The emergeny lumnare must be operatng under mans operaton. The battery must be suffently harged to perform the test. Duraton test The emergeny lumnare must be operatng under mans operaton. The battery must be fully harged to perform the test. Table 50: Test requrements If these requrements are not met, the test s delayed wthn the lmts of the test wndow. On the Status tab, the status of the emergeny lghtng Funton test on hold or Duraton test on hold s set to yes. Set the tme for the test wndow 1. In the Test settngs group feld n the Test wndow dropdown lst, selet a value for the test wndow. 2. Clk on save. Changes are stored n the deve. If the test s not performed wthn the tme defned n the test wndow, on the Status tab, the Test wndow for funton test exeeded or Test wndow for duraton test exeeded status s set to yes. 122

123 Confguraton Dsablng emergeny lumnares! Warnng Suppresson of safety deve! These operatng modes suppress a safety deve. The emergeny lumnares are not swthed on n an emergeny and ths an lead to fataltes or serous physal njures. Make sure that there s not an emergeny and emergeny mode s not requred. To nterrupt the voltage supply wthout the emergeny lumnare beng swthed on, t s possble to use the operatng modes nhbt mode and rest mode. Inhbt mode Rest mode The emergeny lumnare s powered by the mans supply. Inhbt mode lasts no longer than 15 mnutes. Rest mode s enabled nstead of emergeny mode f the voltage supply s nterrupted durng these 15 mnutes. Ths prevents the emergeny lumnare from beng swthed on n emergeny mode. If there s no power outage durng these 15 mnutes, nhbt mode s termnated and mans operaton s restored. The emergeny lumnare remans delberately swthed off whle the voltage supply s nterrupted. Ths funton s used to ensure that the battery s not dsharged n ases where the voltage supply s delberately nterrupted. Applaton example: Mantenane of emergeny lumnares Applaton example: Plant holdays Table 51: The dfferene betw een nhbt mode and rest mode Enable/termnate nhbt mode Requrement: Voltage supply to emergeny lumnare s present. 1. Make sure that emergeny mode s not requred. 2. Clk on Inhbt mode. The operatng mode s enabled. 3. Interrupt the voltage supply wthn 15 mnutes. The emergeny lumnare remans swthed off. Rest mode s enabled. As soon as the emergeny lumnare's voltage supply s restored, mans operaton s enabled. 4. To enable emergeny mode wthout restorng the voltage supply, lk Termnate nhbt/rest mode. Emergeny mode s enabled. Not all ontrol gear for emergeny lghtng supports the Termnate nhbt/rest mode 123

124 Confguraton funton. You an see whether the ontrol gear for emergeny lghtng supports ths status by lookng on the Overvew of funtons tab. If the ontrol gear for emergeny lghtng does not support ths funton, nhbt or rest mode an only be termnated by restorng the voltage supply. The urrent status of ths funton an be seen n the Status tab. Enable/termnate rest mode Requrements: Voltage supply to emergeny lumnare s nterrupted wthout there beng an emergeny. DALI voltage supply s present. 1. Make sure that emergeny mode s not requred. 2. Clk on Rest mode. The operatng mode s enabled. The emergeny lumnare s swthed off. As soon as the emergeny lumnare's voltage supply s restored, mans operaton s enabled. 3. To enable emergeny mode when the voltage supply s nterrupted, lk Termnate nhbt/rest mode. Emergeny mode s enabled. Not all ontrol gear for emergeny lghtng supports the Termnate nhbt/rest mode funton. You an see whether the ontrol gear for emergeny lghtng supports ths status by lookng on the Overvew of funtons tab. If the ontrol gear for emergeny lghtng does not support ths funton, nhbt or rest mode an only be termnated by restorng the voltage supply. Intensty settngs n emergeny mode Here you an set the ntensty wth whh the lamp s llumnated n emergeny mode. The adjustable ntensty s lmted by a lower lmt and an upper lmt. Settng ntensty n emergeny mode 1. Enter a perentage value that les between the lower lmt and the upper lmt for the ntensty n emergeny mode. 2. Clk on save. Changes are stored n the deve. 124

125 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. 125

126 Confguraton Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 52: DALI ontrol gear status nformaton Deve-spef status: Operatng mode Status Desrpton Rest mode atve Indates whether the emergeny lumnare s n rest mode. In rest mode the emergeny lumnare remans delberately swthed off whle the voltage supply s nterrupted. Mans operaton atve Indates whether the emergeny lumnare s n mans operaton. The DALI ontrol gear s powered by the mans supply. Emergeny mode atve Indates whether the emergeny lumnare s n emergeny mode. The DALI ontrol gear s powered by the battery. Emergeny mode after mans return atve Indates whether the emergeny lumnare s n emergeny mode after mans power s restored. Funton test n progress Indates whether a funton test s n progress. Duraton test n progress Indates whether a duraton test s n progress. Hardwred nhbt mode atve Indates whether the emergeny lumnare s n nhbt mode. Inhbt mode s enabled by a swth. If there s a power falure when nhbt mode s atve, rest mode s enabled nstead of emergeny operaton. Ths prevents the emergeny lumnare beng swthed on. Swthed mantaned lght on Indates that, n the ase of swthed mantaned lght, the emergeny lumnare s swthed on n mans mode. Table 53: DALI ontrol gear for emergeny lghtng Deve-spef status: Operatng mode 126

127 Confguraton Deve-spef status: Emergeny lghtng status Status Desrpton Inhbt mode atve Indates whether the emergeny lumnare s n nhbt mode. Inhbt mode was enabled by the DALI ommand Inhbt. Rest mode s enabled nstead of emergeny mode f the voltage supply s nterrupted whle nhbt mode s atve. Ths prevents the emergeny lumnare beng swthed on n emergeny mode. Funton test ompleted Indates whether the latest funton test was ompleted. Duraton test ompleted Ths status does not provde any nformaton as to whether errors were found durng the funton test. Faults are lsted n the Faults group seton. Indates whether the latest duraton test was ompleted. Ths status does not provde any nformaton as to whether faults were found durng the duraton test. Faults are lsted n the Faults group seton. Battery fully harged Indates whether the battery s fully harged. Funton test on hold Indates whether a funton test s on hold. The funton test s delayed wthn the lmts of the test wndow. Possble auses: Emergeny lumnare s n operaton mode Battery not suffently harged Duraton test on hold Indates whether a duraton test s on hold. The duraton test s delayed wthn the lmts of the test wndow. Possble auses: Emergeny lumnare s n operaton mode Battery not fully harged Identfaton atve Indates whether the emergeny lumnare s beng dentfed. Addressed wth Physal Seleton method Indates whether the emergeny lumnare was addressed wth Physal Seleton method. Table 54: DALI ontrol gear for emergeny lghtng Deve-spef status: Emergeny lghtng status 127

128 Confguraton Deve-spef status: Addtonal nformaton Status Desrpton Battery hargng state Indates battery state of harge (%) Tme span duraton test Indates hours of serve reahed at tme of latest duraton test. Lamp burnng hours n emergeny mode Indates how long the lamp was n emergeny mode. Lamp burnng hours n emergeny mode are ndated n 1-hour nrements. Total lamp burnng hours Indates how long the lamp has been n operaton n total (mans operaton and emergeny mode). Total lamp burnng hours are ndated n 4-hour nrements. Rated duraton Indates the tme for whh the battery delvers the requred energy n emergeny mode (usually 1 hour or 3 hours). Reset lamp burnng hours Button used to reset Lamp burnng hours n emergeny mode and Total lamp burnng hours. Table 55: DALI ontrol gear for emergeny lghtng Deve-spef status: Addtonal nformaton Deve-spef status: Faults Status Desrpton Crut defetve Indates whether a rut on the prnted rut board (PCB) of the deve s defetve. Nomnal operatng tme not aheved Indates whether, durng a duraton test, the nomnal operatng tme was not aheved. Battery fault Indates whether there s a battery fault (e.g. open rut, nsuffent battery apaty, battery norretly onneted). Lamp falure deteted durng emergeny mode Indates whether a lamp falure was deteted n emergeny mode or durng an emergeny lghtng test. Test wndow for funton test exeeded Indates whether the test wndow for the funton test was exeeded. Test wndow for duraton test exeeded Indates whether the test wndow for the duraton test was exeeded. Funton test faled Indates whether the latest funton test faled. Duraton test faled Indates whether the latest duraton test faled. Table 56: DALI ontrol gear for emergeny lghtng Deve-spef status: Faults 128

129 Confguraton Overvew of funtons The Overvew of funtons tab shows all funtons supported by ontrol gear of ths deve type. The Overvew of funtons tab s only vsble f advaned settngs have been enabled. Not every ontrol gear element supports all funtons. For ths reason the funtons are shown wth the followng symbols: Ths funton s supported by the ontrol gear. Ths funton s not supported by the ontrol gear. Types of funtons The followng types of funtons are avalable: Confgurable funtons Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Funtons wth dsplayed statuses Ths funtons annot be onfgured. Statuses are shown n the Status tab. Confgurable funtons wth dsplayed statuses Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Statuses are shown n the Status tab. Speal feature Physal Seleton method: If the Physal Seleton method s supported, t an be onfgured under Commssonng 2. Address 21. The ontrol gear s addressed spefally n aordane wth the addressng plan usng the Physal Seleton method. 129

130 Confguraton Deve Type 2: Control gear for hgh-pressure dsharge lamps Control gear for hgh-pressure dsharge lamps are shown n the DALI deve tree dagram wth the the short desrpton HID. symbol and Deve-spef onfguraton Here you an dretly dsplay the address of the hgh-pressure dsharge lamps va the status LED on the deve. For ths purpose, the address s onverted nto a sx-dgt bnary number, whh s represented as a flashng pattern. The red LED stands for bnary number 0, the green LED for bnary number 1. The followng optons are avalable to users n order to onvert a bnary number to a demal number: EM PRO Ident.TOOL software: You an download ths software from Trdon's homepage at: Serves Software. EM PRO addressng tool (Artle number ) In the masterconfigurator software hgh-pressure dsharge lamps an be dentfed as follows. Funton Loate on Desrpton The address of a hgh-pressure dsharge lamps that s hghlghted n the deve tree dagram s dsplayed n an endless loop Is enabled by lkng the Loate on For a detaled desrpton of ths funton, see Seton Chekng deve assgnment After shutdown hgh-pressure dsharge lamps requre some tme to ool down before they an be regnted. Ideally, perform dentfaton proess when lamps are old! If lamps were prevously gnted: Make sure that they ould ool suffently! Table 57: Summary of dentfyng hgh-pressure dsharge lamps 130

131 Confguraton Identfy hgh-pressure dsharge lamp one Clk the Identfy button. The hgh-pressure dsharge lamp's status LED sends the address of the hgh-pressure dsharge lamp one as a bnary flashng pattern. Identfy hgh-pressure dsharge lamp agan 1. Enable the Repeat dentfaton hekbox. 2. Clk the Identfy button. The hgh-pressure dsharge lamp's status LED sends the address of the hgh-pressure dsharge lamp n an endless loop as a bnary flashng pattern. 3. To qut dentfaton, dsable the Repeat dentfaton hekbox. The urrent status of ths funton an be seen n the Status tab. Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. 131

132 Confguraton General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 58: DALI ontrol gear status nformaton 132

133 Confguraton Deve type-spef Status: HID-Status Status Desrpton Run-up tme ready Indates whether the run-up tme s ready. Ar power at requested value Indates whether the requested value of ar power has been reahed after gnton. Watng for gnton Indates whether a lamp ould not be gnted. Identfaton atve Indates whether dentfaton s atve. Table 59: DALI ontrol gear status nformaton Deve type-spef Status: Falures Status Desrpton Mans voltage too low Indates whether mans voltage s too low. Mans voltage too hgh Indates whether mans voltage s too hgh. Converter thermal overload Indates whether the onverter has been thermally overloaded. Ignton tme out Indates whether gnton has been tmed out, that s, the lamp ould not be gnted. Lamp voltage out of spefaton Indates whether lamp voltage s out of spefaton. Lamp ylng falure Indates whether a lamp ylng falure ourred. "Lamp ylng falure" means that the lamp s n a yle of onstantly gntng and gong off agan. Table 60: DALI ontrol gear status nformaton Deve type-spef Status: Stored Falures Status Desrpton Mans voltage too low Indates whether mans voltage s too low. Mans voltage too hgh Indates whether mans voltage s too hgh. Converter thermal overload Indates whether the onverter has been thermally overloaded. Ignton tme out Indates whether gnton has been tmed out, that s, the lamp ould not be gnted. Lamp voltage out of spefaton Indates whether lamp voltage s out of spefaton. Lamp ylng falure Indates whether a lamp ylng falure ourred. "Lamp ylng falure" means that the lamp s n a yle of onstantly gntng and gong off agan. Table 61: DALI ontrol gear status nformaton 133

134 Confguraton Deve Type 3: Control gear for low-voltage halogen lamps Control gear for low-voltage halogen lamps are shown n the DALI deve tree dagram wth the short desrpton low-voltage halogen. symbol and the Control gear onfguraton General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). 134

135 Confguraton Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 62: DALI ontrol gear status nformaton Advaned Status Desrpton Short rut Indates whether a short rut has ourred. Open rut Indates whether there s an open rut. Load derease Indates whether a load derease s present. Load nrease Indates whether a load nrease s present. Overurrent proteton Indates whether the overurrent proteton has been trggered. The overurrent proteton s trggered when the level exeeds or falls below the value of the referene measurement. Thermal shut down Indates whether the permssble temperature of the low-voltage transformer has been exeeded. Thermal overload Not yet supported. Referenng fault Indates whether the referene measurement has faled. Table 63: Advaned status dsplay of DALI ontrol gear for low -voltage halogen lamps Referene measurement Here you an perform a referene measurement. Ths determnes the urrent lamp load usng nternal proesses and measurements. Ths an only be done f the ontrol gear supports ths funton. Performng a referene measurement Clk on Start referene measurement. Referene measurement s performed. Ths lasts approxmately 5 mnutes. If the referene measurement fals, the status Referenng error wll be set to Yes. 135

136 Confguraton Settng parameters Requrement: Control gear onfguraton pop-up wndow open. 1. Clk on the desred parameter. 2. Set the value usng the slder. The on appears. Ths ndates that the ommand has not yet been sent to the DALI ontrol gear. Above the slder, the set value s dsplayed on the left n the relevant unt of measurement and on the rght as a DALI value (demal). 3. Clk on Send ommand. The hange s mplemented n the DALI ontrol gear. The on appears. Ths ndates that the ommand has not yet been sent to the DALI ontrol gear. If the ommand s nonsstent wth another parameter and therefore annot be appled to the DALI ontrol gear, the on ontnues to be dsplayed. Repeat steps 2 and Optonally, test the onfguraton. Informaton on how to hek the onfguraton appears n the pop-up wndow n the help text above the Test onfguraton feld. A detaled desrpton of the onfguraton and ontrol ommands an be found n Seton Confguraton ommands for DALI ontrol gear

137 Confguraton Deve Type 4: Control gear for phase dmmers Control gear for phase dmmers are shown n the DALI deve tree dagram wth the desrpton phase dmmer. symbol and the short Deve-spef onfguraton The dmmng urve an be seleted, fast fade tme an be enabled and a referene measurement an be arred out n the phase dmmers tab. Dmmng urve The ourse of the lumnous flux of the lumnare durng smooth adjustment an be set here. lnear: the lumnous flux s hanged lnearly durng smooth adjustment. Ths does not math the senstvty of the human eye and mght not be pereved as smooth. logarthm: the lumnous flux of the lumnare s hanged logarthmally durng smooth adjustment as per the DALI spefaton. Ths mathes the senstvty of the human eye and s therefore pereved as smooth. Settng the dmmng urve 1. Clk lnear or logarthm. 2. Clk on save. Changes are stored n the deve. The detal vew shows n the Status tab whether a lnear dmmng urve has been seleted. 137

138 Confguraton Referene measurement Here you an perform a referene measurement. Ths determnes the urrent lamp load usng nternal proesses and measurements. Ths an only be done f the ontrol gear supports ths funton. Performng a referene measurement Clk on Start. Referene measurement s performed. Ths lasts approxmately 5 mnutes. If the referene measurement fals, the status Referenng error wll be set to Yes. 138

139 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. 139

140 Confguraton Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 64: DALI ontrol gear status nformaton Deve type spef status: Operatng mode of the ontrol gear (DT4) Status Desrpton Leadng edge atve Indated whether the leadng edge s atve Tralng edge atve Indated whether the tralng edge s atve Referene measurement atve Indated whether the referene measurement s atve Lnear dmmng atve Indated whether the lnear dmmng s atve Tabelle 65: Deve type spef status: Operatng mode of the ontrol gear Deve type spef status: Measurements of the ontrol gear (DT4) Status Desrpton Temperature Dsplays the temperature Mans voltage Dsplays the mans voltage Mans frequeny Dsplays the mans frequeny Load voltage Dsplays the load voltage Load urrent Dsplays the load urrent Load power Dsplays the load power max. Nomnal urrent Dsplays the max. nomnal urrent Tabelle 66: Deve type spef status: Measurements of the ontrol gear Deve type spef status: Errors of the ontrol gear (DT4) Status Desrpton Short rut Indates a short rut Open rut Indates a open rut Load derease Indates a load derease Load nrease Indates a load nrease Thermal shut down Indates a thermal shut down Thermal overload Indates a thermal overload Referenng fault Indates a referenng fault Load does not ft Indates a load does not ft Mans voltage out of range Indates a mans voltage out of range 140

141 Confguraton Mans frequeny out of range Indates a mans frequeny out of range Load voltage out of range Indates a load voltage out of range Overurrent reduton atve Indates a overurrent reduton atve Tabelle 67: Deve type spef status: Errors of the ontrol gear 141

142 Confguraton Overvew of funtons The Overvew of funtons tab shows all funtons supported by ontrol gear of ths deve type. The Overvew of funtons tab s only vsble f advaned settngs have been enabled. Not every ontrol gear element supports all funtons. For ths reason the funtons are shown wth the followng symbols: Ths funton s supported by the ontrol gear. Ths funton s not supported by the ontrol gear. Types of funtons The followng types of funtons are avalable: Confgurable funtons Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Funtons wth dsplayed statuses Ths funtons annot be onfgured. Statuses are shown n the Status tab. Confgurable funtons wth dsplayed statuses Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Statuses are shown n the Status tab. 142

143 Confguraton Deve Type 6: Control gear for LEDs Control gear for LEDs are shown n the DALI deve tree dagram wth the symbol and the short desrpton LED. Deve-spef onfguraton The dmmng urve an be seleted, fast fade tme an be enabled and a referene measurement an be arred out n the LED tab. Dmmng urve The ourse of the lumnous flux of the lumnare durng smooth adjustment an be set here. lnear: the lumnous flux s hanged lnearly durng smooth adjustment. Ths does not math the senstvty of the human eye and mght not be pereved as smooth. logarthm: the lumnous flux of the lumnare s hanged logarthmally durng smooth adjustment as per the DALI spefaton. Ths mathes the senstvty of the human eye and s therefore pereved as smooth. Settng the dmmng urve 1. Clk lnear or logarthm. 2. Clk on save. Changes are stored n the deve. The detal vew shows n the Status tab whether a lnear dmmng urve has been seleted. Fast Fade Tme The Fast Fade Tme an be seleted nstead of the fade tme here. The Fade Tme s gven n seonds. Ths settng an be defned n the Bas onfguraton tab. The Fast Fade Tme s gven n mllseonds (< 25 ms 675 ms). Settng the Fast Fade Tme Requrement: In the Bas onfguraton tab, set the Fade Tme to 0. In the Bas onfguraton tab, set the Extended Fade Tme to Deatvate the hekbox left of fast. Slder turns atve. 2. Set the value usng the slder. 143

144 Confguraton 3. Clk on save. Changes are stored n the deve. The lower lmt of the ontrol gear s shown to the rght of Mnmum. The value hosen wth the slder must be above the lower lmt. Fade Tme, Fast Fade Tme and Extended Fade Tme have dfferent prortes. These prorty settngs determne how the deve ats f values have been assgned to more than one of the parameters. Ths s how the prortes work: Prorty 1 = Fade Tme: If Fade Tme > 0 the Fade Tme s used. If ths s not the ase, prorty 2 beomes atve. Prorty 2 = Fast Fade Tme: If Fast Fade Tme > 0 the Fast Fade Tme s used. If ths s not the ase, prorty 3 beomes atve. Prorty 3 = Extended Fade Tme: If Extended Fade Tme > 0 the Extended Fade Tme s used. If ths s not the ase, the deve s run wth no Fade Tme at all. 144

145 Confguraton Referene measurement Here you an perform a referene measurement. Ths determnes the urrent lamp load usng nternal proesses and measurements. Ths an only be done f the ontrol gear supports ths funton. Performng a referene measurement Clk on Start. Referene measurement s performed. Ths lasts approxmately 5 mnutes. If the referene measurement fals, the status Referenng error wll be set to Yes. 145

146 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. 146

147 Confguraton Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 68: DALI ontrol gear status nformaton Status of ontrol gear for LEDs (DT6) Status Desrpton Short rut Indates whether a short rut has ourred. Open rut Indates whether there s an open rut. Load derease Indates whether a load derease s present. Load nrease Indates whether a load nrease s present. Overurrent proteton Indates whether the overurrent proteton has been trggered. The overurrent proteton s trggered when the level exeeds or falls below the value of the referene measurement. Thermal shut down Indates whether the permssble temperature of the ontrol gear for LEDs has been exeeded. Thermal overload Not yet supported. Referenng fault Indates whether the referene measurement has faled. Pulse wdth modulaton Indates whether the lamps onneted to the ontrol gear are operated wth pulse wdth modulaton. Ampltude modulaton Indates whether the lamps onneted to the ontrol gear are operated wth ampltude modulaton. Current ontrol mode Indates whether the lamps onneted to the ontrol gear are operated wth urrent ontrol. Hgh-urrent pulse Indates whether the lamps onneted to the ontrol gear are operated wth hgh-urrent pulse. Lnear dmmng urves Indates whether a non-logarthm dmmng urve (e.g. lnear dmmng urve) s enabled. Table 69: Deve-spef status nformaton for DALI ontrol gear for LEDs 147

148 Confguraton Overvew of funtons The Overvew of funtons tab shows all funtons supported by ontrol gear of ths deve type. The Overvew of funtons tab s only vsble f advaned settngs have been enabled. Not every ontrol gear element supports all funtons. For ths reason the funtons are shown wth the followng symbols: Ths funton s supported by the ontrol gear. Ths funton s not supported by the ontrol gear. Types of funtons The followng types of funtons are avalable: Confgurable funtons Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Funtons wth dsplayed statuses Ths funtons annot be onfgured. Statuses are shown n the Status tab. Confgurable funtons wth dsplayed statuses Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Statuses are shown n the Status tab. Speal feature Physal Seleton method: If the Physal Seleton method s supported, t an be onfgured under Commssonng 2. Address 21. The ontrol gear s addressed spefally n aordane wth the addressng plan usng the Physal Seleton method. 148

149 Confguraton Deve Type 7: Control gear for swthng funton Control gear for swth ontat are shown n the DALI deve tree dagram wth the desrpton DALI - RM/S. symbol and the short Deve Type 8: Control gear for olour onverters Control gear for olour onverters are shown n the DALI deve tree dagram wth the desrpton olour. symbol and the short Bas onfguraton The group assgnment for ontrol gear and senes and default DALI parameters an be set for eah ontrol gear element n the Bas onfguraton tab. Member of group(s) Member of group(s) spefes the group or groups to whh the ontrol gear belongs. These groups are ndated by the blue bakground. Wth these 16 keys the group membershp an be hanged easly. Settng senes The ntensty of the lumnare and ts olour temperature or xy-oordnates an be set for all 16 senes (0 15) here. The detal vew shows an overvew of the set senes. The settngs an be defned n the Set sene pop-up wndow. Settng senes 1. Enable the hekbox for a sene, n order to assgn an ntensty to the lumnare. The nput feld an be edted. 2. Clk the button. The Set sene pop-up wndow appears. 3. Set the value for the ntensty usng the slder. 149

150 Confguraton -orclk MASK. 4. Selet olour type olour temperature, xy-oordnates or MASK. The vew s updated. 5. Set the olour temperature or xy-oordnates. Adjustng the olour temperature Set the value usng the slder. -orclk the button for a pre-defned olour temperature, e.g K. Settng the xy-oordnates Set the value usng the slders. -orclk the button for pre-defned xy-oordnates, e.g. Bakery produts/gold. 150

151 Confguraton 6. Clk OK. The settngs are appled. The pop-up wndow s losed. 7. Clk on save. Changes are stored n the deve. Settng DALI default parameters DALI default parameters an be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. 2. Clk on save. Changes are stored n the deve. The followng DALI default parameters an be set: DALI default parameters Desrpton Fade tme The seleted value s set as the fade tme n seonds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Fade rate The seleted value s set as the dmmng speed. It ndates by how many steps per seond the ntensty s hanged. The Fade Rate s used wth the DALI ommands Brghten (Up) and Dm (Down). Value range: steps per seond : 45 steps per seond s the DALI default. 358 steps per seond s the fastest fade rate, and 2.8 steps per seond s the slowest. Mnmum Level The seleted value s set as the mnmum level for the ontrol gear. Ths value annot be fallen below durng dmmng/brghtenng. Value range: Physal lower lmt Maxmum level : The physal lower lmt of the ontrol gear s shown to the rght of the Mnmum level as a perentage. The mnmum level must be above ths value. Maxmum Level The seleted value s set as the maxmum level for the ontrol gear. Ths value annot be exeeded durng dmmng/brghtenng. 151

152 Confguraton Value range: Mnmum Level 100% Power On Level The seleted value s set as the value after power s restored. There are two values for the Power On Level: one for ntensty and one for the olour temperature or xy-oordnates. System Falure Level The seleted value s set as the value n the event of falure of the DALI power supply. There are two values for the System Falure Level: one for ntensty and one for the olour temperature or xy-oordnates. Table 70: DALI default parameters Speal feature: Settng the Power On Level and System Falure Level The Power On Level and the System Falure Level are set va a separate pop-up wndow. 1. Clk the button. The Set Power On Level or Set System Falure Level pop-up wndow appears. 2. Set the value for the ntensty usng the slder. -orclk MASK. 3. Selet olour type olour temperature, xy-oordnates or MASK. The vew s updated. 4. Set the olour temperature or xy-oordnates. Adjustng the olour temperature Set the value usng the slder. -orclk the button for a pre-defned olour temperature, e.g K. Settng the xy-oordnates Set the value usng the slders. -orclk the button for pre-defned xy-oordnates, e.g. Bakery produts/gold. 5. Clk OK. The settngs are appled. 152

153 Confguraton 6. Clk on save. Changes are stored n the deve. Deve-spef onfguraton The olour temperature range an be set, automat albraton an be arred out and olours an be dretly hanged n the Colour tab. Colour temperature range The range n whh the olour temperature of the lamps an be hanged an be set here. The olour temperature range s restrted to the physal upper and lower lmts. Mnmum olour temperature: the warmest olour temperature that a lamp an have. Ths temperature s ether the physal lower lmt or s ooler than ths lmt. Maxmum olour temperature: the oolest olour temperature that a lamp an have. Ths temperature s ether the physal upper lmt or s warmer than ths lmt. Settng the mnmum or maxmum olour temperature 1. Set the value for the ndvdual parameter usng the slder. 2. Clk on save. Changes are stored n the deve. The mnmum olour temperature annot be lower than the physal lower lmt. The maxmum olour temperature annot be hgher than the physal upper lmt. Automat albraton The xy-oordnates for all supported prmares an be albrated here. Carryng out automat albraton Clk on Start. Automat albraton begns. It lasts approxmately 15 mnutes. If albraton s ompleted suessfully, the status of the automat albraton s dsplayed n the Status tab as suessful. If albraton was not suessful, the values from the last suessful albraton are automatally loaded. If Stop s lked durng automat albraton, albraton s anelled and the values of the last suessful albraton are loaded. 153

154 Confguraton The urrent status of ths funton an be seen n the Status tab. Immedate olour hange Users an set whether the olour an be mmedately hanged or only usng an Atvate ommand here. These ommands nlude Intensty (DAP), Brghten, Dm and Reall sene X. The fade tme for the ndvdual ommand s used. Dsablng mmedate olour hange 1. Dsable the Colour only hanges wth the "Atvate" ommand hekbox. 2. Clk on save. Changes are stored n the deve. The urrent status of ths funton an be seen n the Status tab. 154

155 Confguraton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol gear Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. Address mssng Indates whether the DALI ontrol gear s unaddressed. 155

156 Confguraton Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 71: DALI ontrol gear status nformaton Status of ontrol gear for olour onverters (DT 8) Status Desrpton xy-oordnates outsde value range Indates whether values were hosen for the xy-oordnates whh are outsde of the value range. The onfgurable value range depends on the LED module onneted to the olour onverter. Colour temperature outsde value range Indates whether a value was hosen for the olour temperature whh s outsde of the value range. The onfgurable value range depends on the LED module onneted to the olour onverter. Automat albraton n progress Indates whether the automat albraton s stll ongong. Automat albraton suessful Indates whether the automat albraton was suessful. If t was not suessful, the values from the last suessful albraton are automatally loaded. Colour type "xy-oordnates" atve Indates whether the "xy-oordnates" olour type s enabled. Colour type "Colour temperature" atve Indates whether the "olour temperature" olour type s enabled. Colour type "Prmary" atve Indates whether the "prmary" olour type s enabled. Colour type "RGBWAF" atve Indates whether the "RGBWAF" olour type s enabled. Table 72: Deve-spef status nformaton for DALI ontrol gear for olour onverters 156

157 Confguraton Overvew of funtons The Overvew of funtons tab shows all funtons supported by ontrol gear of ths deve type. The Overvew of funtons tab s only vsble f advaned settngs have been enabled. Not every ontrol gear element supports all funtons. For ths reason the funtons are shown wth the followng symbols: Ths funton s supported by the ontrol gear. Ths funton s not supported by the ontrol gear. Types of funtons The followng types of funtons are avalable: Confgurable funtons Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Funtons wth dsplayed statuses Ths funtons annot be onfgured. Statuses are shown n the Status tab. Confgurable funtons wth dsplayed statuses Funtons are onfgured n the detal vew, ether n the Bas onfguraton tab or n a deve-spef tab. Statuses are shown n the Status tab. Speal features Number of prmares: If the prmares olour type s supported, the number of prmares s dsplayed. Number of RGBWAF hannels: If the RGBWAF olour type s supported, the number of RGBWAF hannels s dsplayed. 157

158 Confguraton Deve Type 255: Mult-deve types Mult-deve types are shown n the DALI deve tree dagram wth the symbol and the short desrpton Mult. They omprse at least two deve types. There are several ombnatons avalable. The onfguraton optons for the mult-deve type depend on the onfguraton optons for the ndvdual deve types whh make up the mult-deve type. The followng mult-deve types are urrently supported: TALEXXmodule STARK DLE LCAI TW Lnear Deve type 6: Control gear for LEDs 143 Deve type 8: Control gear for olour onverters 149 Deve type 6: Control gear for LEDs 143 Deve type 8: Control gear for olour onverters 149 EMpowerLED PRO DIM Deve type 1: Control gear for emergeny lghtng Deve type 6: Control gear for LEDs 143 LCA 50/100W mA DT8/2xDT8 Deve type 6: Control gear for LEDs 143 Deve type 8: Control gear for olour onverters

159 Confguraton 8.2 DALI XC The DALI XC s represented n the DALI deve tree dagram by the on and the short name DALI XC. When addressng, the DALI XC s gven an ed address (ea) and an be onfgured n the detal vew usng ths address. The masterconfigurator software uses the ountng method gven n DALI standard IEC Addresses, groups and senes are ounted startng wth 0. However there are deves that are ounted startng wth 1, e.g. DALI XC. If sene 1 s seleted va a rotary seletor swth, for example, t s dsplayed n the masterconfigurator software as sene 0. Deve nformaton The followng deve nformaton s dsplayed n the header: Deve nformaton Desrpton Name Dsplays the name of the deve. Artle number Dsplays the artle number of the deve. Seral number Dsplays the unque seral number of the deve. Date of manufature (CW.YYYY) Dsplays the date of manufature of the deve n the format CW.YYYY (alendar week, year). Frmware verson Dsplays the frmware verson of the deve. ed verson Dsplays the verson of the ed spefaton supported by the deve. ed s an enhaned protool based on DALI onnetons. Table 73: Deve nformaton 159

160 Confguraton Bas onfguraton The power on behavour an be set and the urrent onfguraton of the DALI XC an be vewed n the Bas onfguraton tab. Power on behavour The power on behavour ndates how the DALI XC responds after the voltage supply has faled. The power on behavour an be onfgured n all operatng modes. Command Indates whh ommand the DALI XC sends to all of the lumnares onneted to the DALI ontrol lne after the power s restored: Off Reall sene X (0 15) Do not send ommand: If more than one DALI XC s onneted to the DALI ontrol lne, the power on behavour an only be set on one DALI XC. Do not send ommand must be set for all other DALI XC deves. Delay tme Tme after whh the seleted ommand s sent. Value range: 0 7 s Table 74: Confguraton optons for "pow er on behavour" 160

161 Confguraton "Mode" and "Confg" rotary seletor swthes There are two rotary seletor swthes on the DALI XC. (1) Mode rotary seletor swth The operatng mode of the DALI XC an be set va ths rotary seletor swth. (2) Confg rotary seletor swth The nputs of the DALI XC an be onfgured va ths rotary seletor swth. Operatng modes The DALI XC has seven operatng modes (A G), whh are set va the Mode rotary seletor swth. Rotary seletor swth poston Desrpton Confguraton A MC operatng mode: Programmed funtons an be realled va sngle momentary-aton swthes and/or double momentary-aton swthes and/or standard swthes. Ths operatng mode s onfgured va the masterconfigurator software. Rotary seletor swth Confg (2) has no funton here. For a detaled desrpton of the settng optons, see Seton Confguraton of operatng mode "MC"... B SC-A operatng mode: Senes an be realled va sngle momentary-aton swthes. Ths operatng mode s onfgured va rotary seletor swth Confg (2) on the DALI XC. A sene s assgned to eah of the four nputs. The settngs are dsplayed n the masterconfigurator software. C SC operatng mode: Senes an be realled and saved va sngle momentary-aton swthes. Ths operatng mode s onfgured va rotary seletor swth Confg (2) on the DALI XC. A sene s assgned to eah of the four nputs. The settngs are dsplayed n the masterconfigurator software. D GC-A operatng mode: Lumnare groups an be swthed on and off and dmmed and brghtened va sngle momentary-aton swthes and/or double momentary-aton swthes. Ths operatng mode s onfgured va rotary seletor swth Confg (2) on the DALI XC. A lumnare group s assgned to eah of the four nputs. The settngs are dsplayed n the masterconfigurator software. E GC operatng mode: Ths operatng mode s onfgured va rotary seletor

162 Confguraton Rotary seletor swth poston Desrpton Confguraton Lumnare groups an be swthed on and off, dmmed and brghtened, and grouped va sngle momentary-aton swthes and/or double momentaryaton swthes. swth Confg (2) on the DALI XC. A lumnare group s assgned to eah of the four nputs. The settngs are dsplayed n the masterconfigurator software. F PROG operatng mode: Commssonng or a system extenson an be started and ompleted n ths operatng mode. The ontrol ponts for ths DALI XC are loked. All other DALI XC deves an be operated as normal. Ths operatng mode s onfgured va rotary seletor swth Confg (2) on the DALI XC. A lumnare group s assgned to eah of the four nputs. The settngs are dsplayed n the masterconfigurator software. G TuWh operatng mode: The ntensty and olour temperature of Tunable Whte lumnares an be set va double momentary-aton swthes. Ths operatng mode s onfgured va rotary seletor swth Confg (2) on the DALI XC. A lumnare group s assgned to eah of the four nputs. The settngs are dsplayed n the masterconfigurator software. Table 75: Operatng modes of the DALI XC 162

163 Confguraton Confguraton of operatng mode "MC" In the MC operatng mode, sngle momentary-aton swthes and/or double momentary-aton swthes and/or standard swthes an be used to reall programmed funtons. These funtons are onfgured va the masterconfigurator software. The Confg rotary seletor swth has no funton. The DALI XC has four nputs (T1 T4). The effetve range of the respetve nput and ts funton an be set n tabs T1, T2, T3 and T4. Confguraton opton Desrpton Effetve range Range ontrolled va the relevant nput (T1, T2, T3 or T4): All Group (0 15) Address (0 63) Funton Funton stored for the seleted effetve range on the relevant nput (T1, T2, T3 or T4): No funton: The seleted nput has no funton. Momentary-aton swth: more nformaton an be found here Changeover swth: more nformaton an be found here Standard swth: more nformaton an be found here Maro: starwell funton More nformaton an be found here Maro: dynam sene reall More nformaton an be found here Maro: sequental sene reall More nformaton an be found here Maro: user-defned ommand sequene More nformaton an be found here User-defned onfguraton of the nputs: settngs stored on the DALI XC do not orrespond to the settng optons n the masterconfigurator software. As soon as the system s swthed from funton Userdefne onfguraton of the nputs to another funton and ths s saved, the user-defned onfguraton of the nputs s lost and annot be restored. Table 76: Confguraton optons for "MC" operatng mode 163

164 Confguraton Momentary-aton swth The seleted nput s onfgured as a momentary-aton swth. The followng onfguraton optons are avalable for ths funton: Confguraton opton Desrpton Brefly press momentary-aton swth Brefly pressng the momentary-aton swth wll send ommand X1 one tme. The followng ommands an be seleted from the dropdown lst for ommand X1: Ignored Intensty (DAP): n perent Off Maxmum level Mnmum level Last atve level Reall sene X (0 15) A fade tme an also be stored dependng on the ommand. 164

165 Confguraton Confguraton opton Desrpton Hold down momentary-aton swth For a prese desrpton of the DALI ommands, see Seton DALI ommands... Holdng down the momentary-aton swth wll send ommand Y1. The ommands are repeatedly sent for as long as the momentaryaton swth s held down. The followng ommands an be seleted from the dropdown lst for ommand Y1: Ignored Brghten Dm Inrease olour temperature Derease olour temperature A fade rate an also be stored dependng on the ommand. For a prese desrpton of the DALI ommands, see Seton DALI ommands... Table 77: Confguraton optons for the "momentary-aton sw th" funton To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 165

166 Confguraton Changeover swth The seleted nput s onfgured as a hangeover swth. Eah tme the momentary-aton swth s brefly pressed ommand X1 and ommand X2 are sent n alternatng sequene. Eah tme the momentary-aton swth s held down ommand Y1 and ommand Y2 are sent n alternatng sequene. The ommand sent eah tme depends on the lghtng status and s automatally seleted by the DALI XC. The followng onfguraton optons are avalable for ths funton: Confguraton opton Desrpton Brefly press momentary-aton swth Eah tme the momentary-aton swth s brefly pressed ommand X1 and ommand X2 are sent n alternatng sequene. The followng ommands an be seleted from the dropdown lst for ommand X1 and ommand X2: Ignored Intensty (DAP): n perent Off Maxmum level Mnmum level Last atve level Reall sene X (0 15) 166

167 Confguraton Confguraton opton Desrpton Hold down momentary-aton swth For a prese desrpton of the DALI ommands, see Seton DALI ommands... Eah tme the momentary-aton swth s held down ommand Y1 and ommand Y2 are sent n alternatng sequene. The ommands are repeatedly sent for as long as the momentary-aton swth s held down. The followng ommands an be seleted from the dropdown lst for ommand Y1: Ignored Brghten Inrease olour temperature The followng ommands an be seleted from the dropdown lst for ommand Y2: Ignored Dm Derease olour temperature For a prese desrpton of the DALI ommands, see Seton DALI ommands... Table 78: Confguraton optons for the "hangeover sw th" funton To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 167

168 Confguraton Standard swth The seleted nput s onfgured as a standard swth. The followng onfguraton optons are avalable for ths funton: Confguraton opton Desrpton Lghtng-lnked The ommand sent eah tme depends on the lghtng status and s automatally seleted by the DALI XC. Close If the standard swth s onfgured to be lghtng-lnked, no fade tme an be stored for ommand X1 and ommand Y1. When the swth s losed, ommand X1 s sent one tme. The followng ommands an be seleted from the dropdown lst for ommand X1: Ignored Intensty (DAP): n perent Off Maxmum level Mnmum level 168

169 Confguraton Last atve level Reall sene X (0 15) A fade tme an also be stored dependng on the ommand. Open For a prese desrpton of the DALI ommands, see Seton DALI ommands... When the swth s opened, ommand Y1 s sent one tme. The followng ommands an be seleted from the dropdown lst for ommand Y1: Ignored Intensty (DAP): n perent Off Maxmum level Mnmum level Last atve level Reall sene X (0 15) A fade tme an also be stored dependng on the ommand. For a prese desrpton of the DALI ommands, see Seton DALI ommands... Table 79: Confguraton optons for the "standard sw th" funton To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 169

170 Confguraton Maro: starwell funton A momentary-aton swth or standard swth s pressed n a starwell, whh swthes on the lghtng wth ommand X1 and starts the run-on tme. If no one presses a momentary-aton swth or standard swth agan durng the run-on tme, ommand Y1 s then sent. The followng onfguraton optons are avalable for ths funton: Confguraton opton Desrpton Brefly press momentary-aton swth When the momentary-aton swth or standard swth s pressed, ommand X1 s sent one tme. The followng ommands an be seleted from the dropdown lst for ommand X1: Ignored Intensty (DAP): n perent Off Maxmum level Mnmum level Reall sene X (0 15) A fade tme an also be stored dependng on the ommand. 170

171 Confguraton Confguraton opton Desrpton Run-on tme For a prese desrpton of the DALI ommands, see Seton DALI ommands... Tme that starts when the lghtng s swthed on and after whh ommand Y1 s sent. If someone presses a momentary-aton swth or standard swth agan n ths starwell durng the run-on tme, the run-on tme starts agan. Value range: 1 s 60 mn None After run-on tme has expred After run-on tme has expred, ommand Y1 s sent one tme. The followng ommands an be seleted from the dropdown lst for ommand Y1: Ignored Intensty (DAP): n perent Off Maxmum level Mnmum level Reall sene X (0 15) A fade tme an also be stored dependng on the ommand. For a prese desrpton of the DALI ommands, see Seton DALI ommands... Table 80: Confguraton optons for the "starw ell funton" To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 171

172 Confguraton Maro: dynam sene reall A dynam sene reall onssts of no more than 16 senes that are automatally realled one after the other. The order of the senes an be seleted freely. Senes may our more than one n a dynam sene reall. A fade tme and hold tme are defned for eah sene. Brefly pressng the momentary-aton swth onneted to the nput starts the dynam sene reall; one sene after the other s realled. Brefly pressng the momentary-aton swth agan nterrupts the dynam sene reall. The last sene realled remans atve. Brefly pressng the momentary-aton swth agan ontnues the dynam sene reall. Holdng down the momentary-aton swth stops the dynam sene reall and sends an off ommand. Brefly pressng the momentary-aton swth agan starts the dynam sene reall agan from the start. The followng onfguraton optons are avalable for ths funton: Confguraton opton Desrpton Repeat all When the last sene s realled, the sene reall starts agan wth the frst sene. If the dynam sene reall s not repeated, the last hold tme runs ndefntely and the sene s not swthed. Fade tme The tme t takes to hange from one sene to the next. 172

173 Confguraton Confguraton opton Desrpton Value range: fastest s : 90.5 s s the slowest fade tme. Sene Sene beng realled. Senes an be used repeatedly wthn a dynam sene reall. Value range: Sene X (0 15) Hold tme Tme for whh the set sene s held. One the hold tme expres, the next sene s realled wth the defned fade tme. Value range: 1 s 60 mn Ignore: the set fade tme and sene are gnored. Ths settng s used when a sene needs to be removed from a dynam sene reall that s already defned, wthout havng to reonfgure the entre dynam sene reall. Table 81: Confguraton optons for the "maro: dynam sene reall" funton To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 173

174 Confguraton Maro: sequental sene reall A sequental sene reall onssts of no more than 16 senes. The order of the senes annot be nfluened. An off ommand an be sent to the set effetve range after the last sene f desred. Every tme the momentary-aton swth onneted to the nput s pressed, the next seleted sene s realled. One all senes have been realled, the sequental sene reall starts agan from the start. To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. An off ommand from another deve sent to the set effetve range or an off ommand sent to all ontrol gear onneted to the ontrol lne s nterpreted by the DALI XC as suh and the sequental sene reall s stopped. The sequental sene reall starts agan from the start the next tme a momentary-aton swth s pressed. 174

175 Confguraton Maro: user-defned ommand sequene A *.ot fle reated by the user wth user-defned ommands s loaded. Every tme the momentary-aton swth onneted to the nput s pressed, the user-defned ommand sequene s realled. The *.ot fle an be reated wth the ommand admnstrator. A detaled desrpton of the ommand admnstrator an be found n Seton Command admnstrator Defnton of the *.ot fle The effetve range must be defned n the *.ot fle. The *.ot fle an ontan maxmum 20 ommands. The delay tme for sendng the ommands must be 20 ms. If a dfferent tme s defned for sendng the ommands, the masterconfigurator software gnores ths nformaton and uses 20 ms nstead. To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 175

176 Confguraton Status The Status tab shows all status nformaton whh an be quered by the DALI XC. General status of the DALI XC Status Desrpton Ready Indates whether the DALI XC s ready for ommunaton. Fault on at least one nput Indates whether a fault exsts on at least one nput. At least one nput loked: Indates whether at least one nput s loked from operaton. At least one swth frozen To fnd out whh nputs are affeted, press eah nput n order. Status Input Tx pressed shows the nput on whh a fault exsts. The ed ommands an be used to lok and unlok nputs from operaton. Indates whether at least one swth s frozen. Table 82: Status nformaton for the DALI XC 176

177 Confguraton Status of the nputs of the DALI XC Status Desrpton Input T1 Indates whether the momentary-aton swth or standard swth onneted to nput T1 s urrently pressed. Input T2 Indates whether the momentary-aton swth or standard swth onneted to nput T2 s urrently pressed. Input T3 Indates whether the momentary-aton swth or standard swth onneted to nput T3 s urrently pressed. Input T4 Indates whether the momentary-aton swth or standard swth onneted to nput T4 s urrently pressed. Table 83: Status nformaton for the DALI XC 177

178 Confguraton 8.3 DALI MC The DALI MC s represented n the DALI deve tree dagram by the on and s onfgured n the detal vew. The DALI MC has four ndependent nputs. To make t possble to parameterse these nputs freely, eah of the four nputs must have ts own edali address (ea). Confguraton opton Desrpton Power on behavour Spefes how the DALI MC behaves when power s restored: do not send ommand OFF Sene 0 15 Delay tme Tme after whh the seleted ommand s sent. The delay tme s used to take nto aount the start-up tme of the DALI ontrol gear after power s restored. Table 84: Confguraton optons for the DALI MC The behavour when power s restored an only be set va the detal vew of nput T4. Ths funton s not avalable for any of the other nputs. 178

179 Confguraton Parametersng the nputs Requrement: Eah DALI MC nput has ts own edali address (ea). 1. In the DALI deve tree dagram, selet a DALI MC nput. The onfguraton s dsplayed n the detal vew. 2. From the Target drop-down lst, selet the destnaton address to whh the ommand s to apply: All, Group 0 15 or ndvdual Address. 3. From the Confgure funton drop-down lst, selet a funton or maro. 4. Defne the funton va nput felds, lsts and rado buttons. 5. Clk on Save. The onfguraton s saved n the DALI MC. The saved onfguraton an now be tested dretly n the DALI nstallaton. Funtons In the Confgure funton drop-down lst, hoose between the followng funtons: Funton Desrpton 1) Push-button: short or long = 1 * ommand X Brefly pressng or holdng down the push-button wll send ommand X one tme. 2) Push-button: short = 1 * ommand X, long = 1 * ommand X then 1 * ommand Y Brefly pressng the push-button wll send ommand X one tme. Holdng down the push-button wll send ommand X one, and then ommand Y one. 3) Push-button: short = 1 * ommand X, long = 1 * ommand X then repeatedly ommand Y Brefly pressng the push-button wll send ommand X one tme. Holdng down the push-button wll send ommand X one, and then ommand Y repeatedly. 4) Push-button: short = 1* ommand X, long = repeatedly ommand Y Brefly pressng the push-button wll send ommand X one tme. Holdng down the push-button wll repeatedly send ommand Y. 5) Push-button (toggle): short or long = toggle between ommand X and Y Brefly pressng or holdng down the push-button wll alternate between sendng ommands X and Y. 6) Push-button (toggle): short or long = toggle between ommand X and Y, lghtng-based Brefly pressng or holdng down the push-button wll alternate between sendng ommands X and Y. The ommand sent n eah ase depends on the status of the lghtng: If the lghtng was prevously swthed off, ommand X s sent. If the lghtng was prevously swthed on, ommand Y s sent. 179

180 Confguraton 7) Push-button (dmmng key): short = toggle between ommand X and Y, long = dmmng, lghtng-based 8) Swth: lose = ommand X, open = ommand Y SwthDIM mode Brefly pressng on the dmmng key wll alternate between sendng ommands X and Y. The ommand sent n eah ase depends on the status of the lghtng. If the lghtng was prevously swthed off, ommand X s sent. If the lghtng was prevously swthed on, ommand Y s sent. Holdng down the dmmer swth dms or brghtens the lghtng. When the swth s losed, ommand X s sent. When the swth s opened, ommand Y s sent. 9) Changeover swth: lose = ommand X, open = ommand Y, lghtng-based Eah tme the swth s pressed, the ommands X and Y are sent n alternatng order. The ommand sent n eah ase depends on the status of the lghtng: If the lghtng was prevously swthed off, ommand X s sent. If the lghtng was prevously swthed on, ommand Y s sent. 10) Starwell funton: lose = ommand X, start runon tme, run-on tme elapsed = ommand Y If the push-button s pressed, ommand X s sent and the run-on tme starts. One the run-on tme has elapsed, ommand Y s sent. Table 85: DALI MC funtons Commands X and Y represent varables. The followng ommands an be seleted: Intensty (DAP) Off Down Step up Step down Reall max Reall mn Step down and off On and Step up Go to Sene X (0 15) No funton For a prese desrpton of the DALI ommands, see Seton DALI ommands

181 Confguraton Maros In the Confgure funton drop-down lst, hoose between the followng maros: Maro 1: Go home Funton Dm off lumnare wthn a defned tme. Adjustable parameters Fade tme: tme requred to reah the absene level. Reset fade tme: tme requred to reah the presene level agan. Table 86: DALI MC maro 1: Go home Maro 2: MSensor automat Funton Ambent lght ontrol of the DALI MSensor s enabled. Target The destnaton address of the maro s ether All or the edali (ea) of the approprate DALI MSensor. Table 87: DALI MC maro 2: MSensor automat Maro 3: Sequental sene reall Funton Every tme the push-button onneted to the nput s pressed, the next sene s realled. At the end of the sequene, the proess begns agan. Adjustable parameters Senes 0 15: seleton of senes to be realled. Off: seleton of whether an off ommand s to be sent at the end of the sequene. Table 88: DALI MC maro 3: Sequental sene reall The order of the senes annot be nfluened. The senes are always realled n asendng order. 181

182 Confguraton Maro 4: Dynam sene Funton Pressng the push-button realls a sequene of four senes. The fade tme and delay tme an be defned freely for eah sene. Sequene Press the push-button brefly: the sequene starts. Brefly press the push-button wth sene runnng: the sequene stops. Hold down the push-button wth sene runnng: sequene s stopped and an off ommand s sent. Adjustable parameters Delay tme: delay tme before the sene s realled. Ths an be between 0 and 255 seonds. The delay tme for the next sene s therefore the dwell tme for the preedng sene. Fade tme: fade tme for the new sene. Sene: seleton of whh sene s to be realled. Repeat: when the last sene s reahed, the sequene starts agan wth the frst sene. Table 89: DALI MC maro 4: Dynam sene The delay tme before the frst sene only omes nto effet when the sequene s repeated, sne t s the dwell tme of the fourth sene and wll only start rght before the frst sene s realled. It s gnored when the sequene s started wth the push-button. Maro 5: DALI reset Funton Reset for defned deves. Optonally, the addresses may also be deleted. The followng parameters are reset to the reset values: Group and sene settngs Maxmum level, mnmum level Power on level, system falure level Fade tme, fade rate If the DALI ontrol gear possesses other parameters (e.g. epower on level on the PCA lp), they are not reset. Adjustable parameters addtonally delete addresses: the deves are reset and the addresses are deleted. Table 90: DALI MC maro 5: DALI reset The reset values an be found n Seton Reset values

183 Confguraton Maro 6: e-power ON level Funton Sets the power-on level of the DALI ontrol gear to the defned value. DALI deves whh do not support ths funton wll gnore the ommand. Adjustable parameters Memory value: sets the power-on level to the value before power falure (memory value). user-defned: the power-on level s shown as a perentage. In addton, a fade tme an be defned. Table 91: DALI MC maro 6: e-pow er ON level Maro 7: PCA ompatblty Funton Sets the PCA ompatblty parameter n the PCA EXCEL one4all deves to the defned value. DALI deves whh do not support ths funton wll gnore the ommand. Table 92: DALI MC maro 7: PCA ompatblty Maro 8: User-defned DALI ommands Funton Exeutes a *.ot fle that an be reated by the user. The followng ponts must be observed: The *.ot fle must not exeed the lmt of 10 ommands. The destnaton address must be spefed n the *.ot fle. The delay tme from one ommand to another s set to 20 ms and annot be hanged. Table 93: DALI MC maro 8: User-defned DALI ommands 183

184 Confguraton 8.4 DALI basdim DGC DALI basdim DGC s represented n the DALI deve tree dagram by the vew. on and s onfgured n the detal DALI basdim DGC onssts nternally of three deve lasses, whh are lsted ndvdually n the DALI deve tree dagram: Lght sensor: A detaled desrpton of the lght sensor an be found n Seton DALI basdim DGC Lght sensor 192. Moton sensor: A detaled desrpton of the moton sensor an be found n Seton basdim DGC Moton sensor 193. Remote ontrol: A detaled desrpton of the remote ontrol an be found n Seton basdim DGC Remote ontrol 197. Deve nformaton The followng deve nformaton s dsplayed n the header: Deve nformaton Desrpton Name Dsplays the name of the ontrol gear. Lamp type Dsplays the lamp type of the lamp onneted to the ontrol gear. Artle number Dsplays the artle number of the ontrol gear. Seral number Dsplays the unque seral number of the ontrol gear. Date of manufature Dsplays the date of manufature for the ontrol gear. Frmware verson Dsplays the frmware verson of the ontrol gear. DALI verson Dsplays the verson of the DALI spefaton supported by the ontrol gear. ed verson Dsplays the verson of the ed spefaton supported by the ontrol gear. ed s an enhaned protool based on DALI onnetons. Table 94: Deve nformaton 184

185 Confguraton Bas onfguraton The group assgnment for ontrol gear and senes and default DALI parameters an be set for eah ontrol gear element n the Bas onfguraton tab. Member of group(s) Member of group(s) spefes the group or groups to whh the ontrol gear belongs. These groups are ndated by the blue bakground. Wth these 16 keys the group membershp an be hanged easly. Senes The ntensty of the dfferent outputs an be set for all 16 senes (0 15) here. Settng senes 1. Enable the hekbox for a sene, n order to assgn an ntensty to the lumnare. The nput feld an be edted. 2. For Output 1 and Output 2: Enter a value between 0 % and 100 %. 3. For Relay output: Enter off, on or MASK. 4. To defne settngs for addtonal senes, repeat steps 1 and Clk on save. Changes are stored n the deve. MASK means that the lumnare n ths group wll retan ts urrent ntensty when the relevant sene s realled. 185

186 Confguraton DALI default parameters DALI default parameters an be set here. Settng DALI default parameters 1. Set the value for the ndvdual parameter usng the slder. The value s shown to the left of the slder. 2. Clk on save. Changes are stored n the deve. The followng DALI default parameters an be set: DALI default parameters Desrpton Fade tme The seleted value s set as the fade tme n seonds. Value range: < s : < 0.7 s s the DALI default. < 0.7 s s the fastest fade tme, and 90.5 s s the slowest. Mnmum level The seleted value s set as the mnmum level for the ontrol gear. Ths value annot be fallen below durng dmmng/brghtenng. Value range: Physal lower lmt Maxmum level : The physal lower lmt of the ontrol gear s shown to the rght of the Mnmum level as a perentage. The mnmum level must be above ths value. Maxmum level The seleted value s set as the maxmum level for the ontrol gear. Ths value annot be exeeded durng dmmng/brghtenng. Value range: Mnmum Level 100% Table 95: DALI default parameters To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 186

187 Confguraton Room profles In the Room profles tab you an hoose and atvate a room profle. The followng fve room profles are avalable: Image Profle name Desrpton Indvdual room Two llumnaton areas (wndows area, rest of the room), two swthes, moton sensor(s) Swth 1 operates the lghtng of the wndows area, swth 2 operates the lghtng of the rest of the room. Classroom Three llumnaton areas (wndows area, rest of the room, separate presentaton area), two swthes, moton sensor(s) Swth 1 operates the lghtng of the wndows area and the rest room of the room together (rato of the two dmmng levels remans the same), button 2 operates the presentaton area. Corrdor One llumnaton areas, swthes, moton sensor(s) Swthes operates the lghtng of all the lumnares. Dfferent dmmng levels an be defned for presene deteton n another room (neghbourhood funton), for presene deteton n the orrdor tself and for the absene of any presene deteton. Restroom Two llumnaton areas (snk and mrror area, tolet area), two swthes, moton sensor(s) Swth 1 operates the lghtng of the snk and mrror area, swth 2 operates the lghtng of the tolet area. In onneton wth presene deteton dfferent dmmng levels an be defned for the two lghtng areas. 187

188 Confguraton Image Profle name Desrpton Free-standng lumnare Two llumnaton areas (dret and ndret lghtng), two swthes, moton sensor(s) Swth 1 ontrols dret lghtng, swth 2 ontrols ndret lghtng. If no presene s deteted the free-standng lumnare s swthed off ompletely to avod stand by losses. Tabelle 96: Room profles of the DALI basdim DGC Wth the neghbourhood funton presene deteton an be transfered from one room to another. By default the neghbourhood funton s deatvated. Clkng on Reset, resets the urrent profle to ts default values Deve-spef onfguraton If the hekbox Lok desred value has been atvated, the nomnal value annot be hanged va remote ontrol or the momentary-aton swth nput. Inputs 188

189 Confguraton Confguraton opton Desrpton Effetve range: Range that s operated by momentary-aton swth nput T1 and T2: Output 1 Output 2 Relay output Brefly press momentary-aton swth Determnes the reaton of the lghtng when the momentary-aton swth s brefly pressed: no funton only on only off on/off Hold down momentary-aton swth Determnes the reaton of the lghtng when the momentary-aton swth s held down: no funton brghten dm brghten/dm Double lk the momentary-aton swth Determnes the reaton of the lghtng when the momentary-aton swth s double lked: no funton save desred value Table 97: Confguraton optons for the "momentary-aton sw th" funton Output 1, 2 and relay Confguraton opton Desrpton Output 1 and output 2 Determnes the settngs for output 1 and output 2: both outputs: DSI both outputs: DALI output 1: DALI; output 2: lnkng (DALI In Deatvated) output 1: DSI; output 2: lnkng (DALI In Deatvated) Dfferene from output 2 to output 1: Determnes the dfferene from output 2 to output 1: Range of values: -95% - +95%, adjustable n 5% steps 189

190 Confguraton Confguraton opton Desrpton Operatng Determnes the settngs for the operaton mode: Standby: If the basdim DGC module s swthed off, the relay wll swth off (after 10 mnutes). If the basdim DGC s swthed on, the relay wll swth on. Swthng: relay n standby mode onlyoff: The relay s swthed on va momentary-aton swth or remote ontrol. The relay s swthed off va the presene detetor f no presene s deteted. ON/OFF: The relay s swthed on or off va the presene detetor. Relay output: The relay an be used as 3rd output hannel. Delay tme: Determnes the settngs for the delay tme. (In energy-savng mode the ontat s opened after the delay tme) Range of values: 1-30 mn, default: 10 mn Table 98: Confguraton optons for the "momentary-aton sw th" funton Status The Status tab shows all status nformaton whh an be quered by the ontrol gear. An overvew of whh funtons are supported by the ontrol gear an be found n the Overvew of funtons tab. Ths tab s only vsble f advaned settngs have been enabled. General status of ontrol module Status Desrpton Ready Indates whether the DALI ontrol gear s ready for ommunaton. Lamp falure Indates whether a lamp falure (short rut, open rut, load derease or load nrease) has ourred. Lamp on Indates whether the lamp s on. Lmt volaton Indates that the lumnare was unable to swth to a value, as ths value was outsde of the defned range (mnmum level and maxmum level). Fade tme atve Indates whether a deve s hangng from one ontrol value to another. Reset values Indates whether the DALI ontrol gear has been reset to the reset values. 190

191 Confguraton Address mssng Indates whether the DALI ontrol gear s unaddressed. Power On Level Indates whether the DALI ontrol gear has gone to the Power On Level. Table 99: Status nformaton of the ontrol module 191

192 Confguraton Lght sensor If several sensors are onnteted to the DALI basdim DGC, all these sensors have the same settngs. Confguraton optons n dret master mode The followng onfguraton optons are dsplayed for the lght sensor n dret master mode: Confguraton opton Desrpton Ambent lght ontrol output 1: Ambent lght ontrol an be enabled or dsabled. Ambent lght ontrol output 2: Avalable optons: not enabled onneted to output 1 Desred value: Value used by the lght sensor to regulate the ontrol gear. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Value range: lx 192

193 Confguraton Control speed: Speed at whh the ontrol gear reahes the desred value. Value range: nrements 0 7, wth 0 beng the slowest and 7 the fastest. Automat ontrol: Indates the sene used to ontrol the lghtng based on whether presene s deteted. If ths sene s realled the moton sensor s enabled and the lumnares are ontrolled based on whether presene s deteted. Value range: Sene 0-15 The sene seleted here s dentfed n the Bas onfguraton as automat. Response to manual dmmng: Avalable optons: dsable ambent lght ontrol permanent desred value hange temporary desred value hange Enable dmmng off (brght out) Chekbox enabled: f the measured llumnane exeeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swthed off even f moton s deteted n the room. As soon as the measured llumnane falls below the desred value, the lumnare group s swthed on agan. Dsplay flashng pattern on sensor status LED: Chekbox enabled: Deve status s dsplayed by a flashng pattern on sensor status LED. Threshold Value above whh the lumnare group s swthed off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whh the threshold must be exeeded n order for the lumnare group to be swthed off by the lght sensor. Value range: mn Table 100: Lght sensor onfguraton optons n dret master mode Moton sensor If several sensors are onnteted to the DALI basdim DGC, all these sensors have the same settngs. 193

194 Confguraton Confguraton optons Confguraton opton Desrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatally swthed on and off dependng on whether presene s deteted. (fatory settng) enabled (only OFF): the moton sensor swthes the lghtng off only. It must be swthed on manually. dsabled: the moton sensor s dsabled. The lghtng must be swthed on and off manually. : The never OFF funton s mplemented as follows: 1. Selet the enabled operatng mode. 2. Selet swth-off delay never OFF. Power on behavour Indates how the moton sensor wll reat after falure of the DALI power supply: Standby presene value Fade-n tme Tme requred to reah the presene value. 194

195 Confguraton Value range: fast s Presene value Value to whh the lumnare group swthes when presene s deteted n the room. Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. Value range: 30 s - 60 mn adaptve: The adaptve run-on tme adapts the length of the run-on tme automatally (between 4 and 20 mn.) The length s alulated dependng on the number of presene detetons. Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Value range: fast s Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Value range: 0 s 60 mn never OFF: the lghtng remans at the absene value untl further movement s deteted and the moton sensor swthes to the presene value. The lumnare group s never swthed off by the moton sensor. Absene value Level to whh the lumnare group swthes durng the swth-off delay. Fade-out tme Tme requred to dm off from the absene value. Value range: fast s Dead tme (manual off) Tme started by manually swthng off the lghtng va the momentary-aton swth or the remote ontrol and durng whh the moton sensor s dsabled. If movement s deteted n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s deteted n the room, the moton sensor s enabled agan. Value range: 0 s - 10 mn Send own presene as Value range: Group

196 Confguraton Broadast Send own presene as defnes a unque group dentfer for the basdim DGC. If the basdim DGC transmts nformaton va the neghborhood funton, ths group dentfer s also transmtted. E.g. DGC s n DALI group 0, but t s possble that t sends hs own presene as G5. Response to presene deteted by other basdim DGC deves Ths settng determnes how the moton sensor responds when presene s deteted n another group. Three settngs n total an be onfgured. MASK: the basdim DGC gnores the presene deteted n another group (fatory settng). Presene value: the lumnare group assgned to the basdim DGC swthes to the presene value. Absene value: the lumnare group assgned to the basdim DGC swthes to the absene value. Exepton: f the lumnares are already at the presene value, they retan ths settng. It s possble to program the response for up to fve groups. E.g. Response to G1, G2, G3, G4, G5. By default the basdim DGC wll send nformaton about ts own presene as Broadast ommand. If you program the neghbourhood funton va the DGC programmer, ths behavour hanges: The basdim DGC wll start sendng ts own presene as Group 0 ommand and wll only respond to presene deteted n Group 0. Dsplay flashng pattern on sensor status LED Chekbox enabled: Deve status s dsplayed by a flashng pattern on sensor status LED Table 101: Moton sensor onfguraton optons n dret master mode To apply the hanged values, lk on save. The saved onfguraton an now be tested dretly n the feld. 196

197 Confguraton Remote ontrol Confguraton optons n dret master mode The followng deve nformaton s dsplayed for the remote ontrol n dret master mode: Confguraton opton Desrpton Bas funton Operatng funtons of the remote ontrols: natve: the keys of the remote ontrol are natve. atve: the keys of the remote ontrol are atve. Table 102: Remote ontrol onfguraton optons n dret master mode 8.5 DALI MSensor The masterconfigurator an be used to onfgure the followng versons of the DALI MSensor: MSensor 5DPI DALI MSensor 02 (verson 2.0) DALI MSensor (verson 1.5) 229 DALI MSensor (verson 1.3)

198 Confguraton MSensor 5DPI 14 DALI MSensors are represented by four dfferent symbols n the DALI deve tree. MSensor 5DPI 14 onssts nternally of three deve lasses, whh are lsted ndvdually n the DALI deve tree dagram: Lght sensor: A detaled desrpton of the lght sensor an be found n Seton MSensor 5DPI 14 > Lght sensor 201. Moton sensor: A detaled desrpton of the moton sensor an be found n Seton MSensor 5DPI 14 > Moton sensor 207. Remote ontrol: A detaled desrpton of the remote ontrol an be found n Seton MSensor 5DPI 14 > Remote ontrol 211. Group onept The group assgnment for the MSensor 5DPI 14 s dsplayed. Lumnare group: DALI group (G) ontanng the MSensor 5DPI 14. All deves n ths group are ontrolled by the MSensor 5DPI 14. The followng groups are also dsplayed f advaned settngs have been enabled: Lght sensor group: ed group (eg) ontanng the lght sensor. Moton sensor group: ed group (eg) ontanng the moton sensor. Remote ontrol group: ed group (eg) ontanng the remote ontrol. Effetve range The MSensor 5DPI 14 ontrols ether all deves (broadast) or one DALI group. 198

199 Confguraton Assgnment va the masterconfigurator When the MSensor 5DPI 14 s not assgned to a group n the DALI deve tree dagram, t ontrols all lumnare groups. To ontrol an ndvdual group the MSensor 5DPI 14 must be assgned to an ndvdual group. 1. In the DALI deve tree dagram, lk on the MSensor 5DPI 14 to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the MSensor 5DPI 14 to the desred lumnare group. (Drag & Drop) The MSensor 5DPI 14 s removed from the ndvdual (non-grouped) seton of the DALI deve tree dagram and s added to the desred lumnare group. 199

200 Confguraton Operatng modes The MSensor 5DPI 14 supports two operatng modes. The operatng mode an only be hanged when the advaned settngs are enabled. Dret master mode (fatory settng) Funton: Master Tasks: Send DALI ommands to DALI ontrol gear Send ed ommands to other MSensor 5DPI 14 deves Addressng: The MSensor 5DPI 14 has one DALI address. The lght sensor, moton sensor and remote ontrol eah have one ed address. Slave mode Funton: Slave Tasks: Respond to DALI and ed ommands from a master deve Addressng: The MSensor 5DPI 14 has one DALI address. The lght sensor, moton sensor and remote ontrol eah have one ed address. In slave mode the rotary swth on the bak of the MSensor 5DPI 14 does not have a funton. 200

201 Confguraton Lght sensor The lght sensor supports two operatng modes: Dret master mode Slave mode: the lght sensor annot be onfgured n ths operatng mode. The lght sensor just responds to ommands from the master deve. More nformaton on these operatng modes an be found n Seton MSensor 5DPI Dret master mode 201

202 Confguraton Status n dret master mode The followng status nformaton s dsplayed for the lght sensor n dret master mode: Status Desrpton Illumnane Illumnane urrently measured at the lght sensor. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Update status automatally Indates whether the lght sensor status s updated automatally. Ambent lght ontrol Indates the status of ambent lght ontrol for the lght sensor. enabled: ambent lght ontrol s enabled. temporarly dsabled: ambent lght ontrol has been temporarly dsabled manually by the user. dsabled: ambent lght ontrol s dsabled. unknown: there s urrently no onneton to the lght sensor. Referene deve Indates the DALI ontrol gear used as a referene for alulatng the swth-on level durng ambent lght ontrol. If no referene deve has been assgned to the lght sensor, no deve wll be dsplayed. : Seton Referene deve referene deve s assgned. 206 explans how a Table 103: Lght sensor status nformaton n dret master mode Confguraton optons n dret master mode The followng onfguraton optons are dsplayed for the lght sensor n dret master mode: Confguraton opton Desrpton Ambent lght ontrol Ambent lght ontrol an be enabled or dsabled. Desred value Value used by the lght sensor to regulate the ontrol gear. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Value range: lx Control speed Speed at whh the ontrol gear reahes the desred value. Value range: nrements 0 7, wth 0 beng the slowest and 7 the fastest. 202

203 Confguraton Swth-on level Level when the lghtng s swthed on. Ambent lght ontrol starts from ths value. Mnmum level Maxmum level alulated: the swth-on level for ambent lght ontrol s speally alulated so that t s as lose to the desred value as possble. Enable dmmng off (brght out) Chekbox enabled: f the measured llumnane exeeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swthed off by the lght sensor even f moton s deteted n the room. As soon as the measured llumnane falls below the desred value, the lumnare group s swthed on agan. Threshold Value above whh the lumnare group s swthed off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whh the threshold must be exeeded n order for the lumnare group to be swthed off by the lght sensor. Value range: mn Table 104: Lght sensor onfguraton optons n dret master mode 203

204 Confguraton Settng the response of the MSensor 5DPI 14 to a sene reall In the detal vew of the MSensor 5DPI 14 ts response to a sene reall an be set. A response an be onfgured for eah of the 16 senes. The followng onfguraton optons are avalable: Confguraton Lght sensor Moton sensor automat The lumnare group assgned to the lght sensor swthes to the presene value. Ambent lght ontrol s enabled. Moton sensor dsabled: the moton sensor s enabled. The run-on tme starts over. Moton sensor enabled: the run-on tme starts over. stat The lumnare group assgned to the lght sensor swthes to the ntensty set n the ontrol gear for the sene n queston. If ambent lght ontrol was enabled before the sene was realled, t s temporarly (aordng to the run-on tme) dsabled. Moton sensor dsabled: the moton sensor s enabled. The run-on tme starts over. Moton sensor enabled: the run-on tme starts over. off The lumnare group assgned to the lght sensor s swthed off. The moton sensor swthes to status Dead tme (manual off) n progress. MASK The lght sensor gnores the sene reall. The moton sensor gnores the sene reall. Table 105: Response of the DALI MSensor 02 to a sene reall If the response to a sene reall s set to automat, off or MASK, the MASK value for ths sene must be set for all ontrol gear elements. Informaton on how senes are onfgured an be found n Seton DALI ontrol gear > Confguraton va the detal vew 40. Advaned settngs n dret master mode The followng advaned settngs are dsplayed for the lght sensor n dret master mode f ambent lght ontrol has been enabled. Advaned settngs The "Maxmum level" ommand starts ambent lght ontrol. Desrpton Chekbox dsabled: after the Maxmum level ommand s reeved, the lumnare group swthes to the maxmum level untl the run-on tme for the moton sensor has expred. If ambent lght ontrol was enabled before the Maxmum level ommand was reeved, t s temporarly 204

205 Confguraton dsabled. Chekbox enabled: after the Maxmum level ommand s reeved, the lumnare group swthes to the maxmum level. Ambent lght ontrol s started. The "Brghten" and "Dm" ommands temporarly hange the desred value for ambent lght ontrol. Chekbox dsabled: after a Brghten or Dm ommand s reeved, the lumnare group s smoothly adjusted aordngly. The desred value for ambent lght ontrol remans unhanged. Chekbox enabled: after a Brghten or Dm ommand s reeved, the lumnare group s smoothly adjusted aordngly. The measured llumnane on the DALI MSensor after smooth adjustment s temporarly saved as a new desred value for ambent lght ontrol. The desred value s reset one the run-on tme has expred or an OFF ommand s reeved. Table 106: Lght sensor advaned settngs n dret master mode To apply the hanged values to the lght sensor, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 205

206 Confguraton Referene deve The lght sensor requres a referene deve n order to exatly alulate the swth-on level for ambent lght ontrol. A referene deve s a DALI ontrol gear element loated n the same group as the MSensor 5DPI 14. The masterconfigurator automatally adds the frst DALI ontrol gear element loated n the same group as the MSensor 5DPI 14 as a referene deve. If another DALI ontrol gear element s desred for use as a referene deve, remove the referene deve and add the desred DALI ontrol gear element agan. Removng a referene deve Requrement: Advaned settngs enabled. Clk Remove n the detal vew of the lght sensor. The referene deve s removed. Addng a referene deve Requrement: MSensor 5DPI 14 has been assgned to a DALI group. 1. In the DALI deve tree dagram, lk on the deve to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the deve to the desred group. (Drag & Drop) The deve s removed from the group n whh t was prevously loated and s added to the desred group. The address of the DALI ontrol gear element s automatally dsplayed as the referene deve n the MSensor 5DPI 14. If the DALI ontrol gear element used as a referene deve by the MSensor 5DPI 14 (or the MSensor 5DPI 14 tself) s deleted from the DALI group, the nformaton for the referene deve n the MSensor 5DPI 14 s also deleted. For Referene deve the followng appears: none. 206

207 Confguraton Moton sensor The moton sensor supports two operatng modes: Dret master mode Slave mode: the moton sensor annot be onfgured n ths operatng mode. The moton sensor just responds to ommands from the master deve. More nformaton on these operatng modes an be found n Seton MSensor 5DPI Dret master mode Status n dret master mode The followng status nformaton s dsplayed for the moton sensor n dret master mode: Status Desrpton Moton sensor Indates the status of the moton sensor: Off Lghtng at presene value 207

208 Confguraton Lghtng at presene value, run-on tme n progress Lghtng fadng to absene value, fade tme n progress Lghtng at absene value Lghtng at absene value, swth-off delay n progress Dead tme (manual off) n progress Update status automatally Indates whether the moton sensor status s updated automatally. Table 107: Moton sensor status nformaton n dret master mode Confguraton optons n dret master mode The followng onfguraton optons are dsplayed for the moton sensor n dret master mode: Confguraton opton Desrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatally swthed on and off dependng on whether presene s deteted. (fatory settng) enabled (only OFF): the moton sensor swthes the lghtng off only. It must be swthed on manually. dsabled: the moton sensor s dsabled. The lghtng must be swthed on and off manually. : The never OFF funton s mplemented as follows: 1. Selet the enabled operatng mode. 2. Selet swth-off delay never OFF. Power on behavour Indates how the moton sensor wll reat after falure of the DALI power supply: no aton last state maxmum level off presene value: speally alulated value for ambent lght ontrol. Fade-n tme Tme requred to reah the presene value. Value range: fast s Presene value Value to whh the lumnare group swthes when presene s deteted n the room. The presene value ontrol depends on how the lght sensor s onfgured. ambent lght-ontrolled: If ambent lght ontrol s enabled for the lght sensor, the presene value s regulated based on ambent lght levels. fxed: If ambent lght ontrol s dsabled for the lght sensor, a value an be set as a perentage between 0 100%. 208

209 Confguraton Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. Value range: 30 s 60 mn nfnte: the run-on tme ontnues wthout end. Ths means that the lumnares reman at the defned presene value (ambent lght-ontrolled or fxed). The fade tme does not start. Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Value range: fast s Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Value range: 0 s 60 mn never OFF: the lghtng remans at the absene value untl further movement s deteted and the moton sensor swthes to the presene value. The lumnare group s never swthed off by the moton sensor. Absene value Level to whh the lumnare group swthes durng the swth-off delay. Fade-out tme Tme requred to dm off from the absene value. Value range: fast s Dead tme (manual off) Tme started by manually swthng off the lghtng va the momentary-aton swth or the remote ontrol and durng whh the moton sensor s dsabled. If movement s deteted n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s deteted n the room, the moton sensor s enabled agan. Value range: 0 s 20 mn Table 108: Moton sensor onfguraton optons n dret master mode 209

210 Confguraton Overvew of onfguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swth-off delay 5) Fade-out tme A) Presene value B) Absene value Advaned settngs n dret master mode The followng advaned settngs are dsplayed for the moton sensor n dret master mode: Advaned settngs Desrpton Set response to presene n other groups Ths settng determnes how the moton sensor responds when presene s deteted n another group. Four groups n total an be onfgured. MASK: the DALI MSensor 02 gnores the presene deteted n another group (fatory settng). Presene value: the lumnare group assgned to the DALI MSensor 02 swthes to the presene value. Absene value: the lumnare group assgned to the DALI MSensor 02 swthes to the absene value. Exepton: f the lumnares are already at the presene value, they retan ths settng. Table 109: Moton sensor advaned settngs n dret master mode To apply the hanged values to the moton sensor, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 210

211 Confguraton Remote ontrol The remote ontrol supports two operatng modes: Dret master mode Slave mode: the remote ontrol annot be onfgured n ths operatng mode. The remote ontrol has no funton. More nformaton on these operatng modes an be found n Seton MSensor 5DPI Dret master mode Confguraton optons n dret master mode The followng deve nformaton s dsplayed for the remote ontrol n dret master mode: Confguraton opton Desrpton Confguraton Confguraton of the remote ontrol: Inatve: the keys of the remote ontrol are natve. Fatory settngs: the remote ontrol keys are assgned wth default settngs. The lumnare group s set usng the rotary swth n the battery ompartment of the remote 211

212 Confguraton ontrol. user-defned: the keys of the remote ontrol an be assgned to seleted funtons. Table 110: Remote ontrol onfguraton optons n dret master mode Parametersng the key assgnment Wth the user-defned onfguraton, the key assgnment of the remote ontrol an be parametersed by the user. If key assgnment s ustomsed, the group assgnment as defned by the rotary swth n the battery ompartment of the remote ontrol s gnored. The ommands only apply to the lumnare group set dretly on the rotary swth on the DALI MSensor 02. Dependng on the key, varous onfguraton optons are avalable: On Off On/Off Brghten Dm Sene 0 15 Intensty 1 100% Ambent lght ontrol Reserved: ths opton s reserved for future funtonal enhanements and urrently has no funton. To apply the hanged values to the remote ontrol, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 212

213 Confguraton DALI MSensor 02 (verson 2.0) DALI MSensors are represented by four dfferent symbols n the DALI deve tree. DALI MSensor 02 onssts nternally of three deve lasses, whh are lsted ndvdually n the DALI deve tree dagram: Lght sensor: A detaled desrpton of the lght sensor an be found n Seton DALI MSensor 02 (V2.0) > Lght sensor 216. Moton sensor: A detaled desrpton of the moton sensor an be found n Seton DALI MSensor 02 (V2.0) > Moton sensor 222. Remote ontrol: A detaled desrpton of the remote ontrol an be found n Seton DALI MSensor 02 (V2.0) > Remote ontrol 226. Group onept The group assgnment for the DALI MSensor 02 s dsplayed. Lumnare group: DALI group (G) ontanng the DALI MSensor 02. All deves n ths group are ontrolled by the DALI MSensor 02. The followng groups are also dsplayed f advaned settngs have been enabled: Lght sensor group: ed group (eg) ontanng the lght sensor. Moton sensor group: ed group (eg) ontanng the moton sensor. Remote ontrol group: ed group (eg) ontanng the remote ontrol. Effetve range The DALI MSensor 02 ontrols ether all deves (broadast) or one DALI group. Assgnment va the rotary swth The effetve range of the DALI MSensor 02 s set usng the rotary swth on the bak of the sensor. All ontrol gear elements n the set effetve range are ontrolled by the DALI MSensor 02. Poston of the rotary swth on the DALI MSensor 02 Effetve range 0 All (broadast) 1 Group 0 2 Group Groups 2 8 A F Groups 9 14 Table 111: Poston of the rotary sw th on the DALI MSensor 02 and ts orrespondng effetve range 213

214 Confguraton Assgnment va the masterconfigurator When the DALI MSensor 02 s not assgned to a group n the DALI deve tree dagram, t ontrols the lumnare group set usng the rotary swth on the bak of the sensor. It must be assgned to a group to ontrol an ndvdual group. 1. In the DALI deve tree dagram, lk on the DALI MSensor 02 to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the DALI MSensor 02 to the desred lumnare group. (Drag & Drop) The DALI MSensor 02 s removed from the ndvdual (non-grouped) seton of the DALI deve tree dagram and s added to the desred lumnare group. The poston of the rotary swth on the bak of the DALI MSensor 02 s gnored. If the group assgnment n the masterconfigurator s undone, the rotary swth poston wll be atve agan. 214

215 Confguraton Operatng modes The DALI MSensor 02 supports two operatng modes. The operatng mode an only be hanged when the advaned settngs are enabled. Dret master mode (fatory settng) Funton: Master Tasks: Send DALI ommands to DALI ontrol gear Send ed ommands to other DALI MSensor 02 deves Addressng: The DALI MSensor 02 has one DALI address. The lght sensor, moton sensor and remote ontrol eah have one ed address. Slave mode Funton: Slave Tasks: Respond to DALI and ed ommands from a master deve Addressng: The DALI MSensor 02 has one DALI address. The lght sensor, moton sensor and remote ontrol eah have one ed address. In slave mode the rotary swth on the bak of the DALI MSensor 02 does not have a funton. 215

216 Confguraton Lght sensor The lght sensor supports two operatng modes: Dret master mode Slave mode: the lght sensor annot be onfgured n ths operatng mode. The lght sensor just responds to ommands from the master deve. More nformaton on these operatng modes an be found n Seton DALI MSensor Dret master mode 216

217 Confguraton Status n dret master mode The followng status nformaton s dsplayed for the lght sensor n dret master mode: Status Desrpton Illumnane Illumnane urrently measured at the lght sensor. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Update status automatally Indates whether the lght sensor status s updated automatally. Ambent lght ontrol Indates the status of ambent lght ontrol for the lght sensor. enabled: ambent lght ontrol s enabled. temporarly dsabled: ambent lght ontrol has been temporarly dsabled manually by the user. dsabled: ambent lght ontrol s dsabled. unknown: there s urrently no onneton to the lght sensor. Referene deve Indates the DALI ontrol gear used as a referene for alulatng the swth-on level durng ambent lght ontrol. If no referene deve has been assgned to the lght sensor, no deve wll be dsplayed. : Seton Referene deve referene deve s assgned. 221 explans how a Table 112: Lght sensor status nformaton n dret master mode Confguraton optons n dret master mode The followng onfguraton optons are dsplayed for the lght sensor n dret master mode: Confguraton opton Desrpton Ambent lght ontrol Ambent lght ontrol an be enabled or dsabled. Desred value Value used by the lght sensor to regulate the ontrol gear. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Value range: lx Control speed Speed at whh the ontrol gear reahes the desred value. Value range: nrements 0 7, wth 0 beng the slowest and 7 the fastest. 217

218 Confguraton Swth-on level Level when the lghtng s swthed on. Ambent lght ontrol starts from ths value. Mnmum level Maxmum level alulated: the swth-on level for ambent lght ontrol s speally alulated so that t s as lose to the desred value as possble. Enable dmmng off (brght out) Chekbox enabled: f the measured llumnane exeeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swthed off by the lght sensor even f moton s deteted n the room. As soon as the measured llumnane falls below the desred value, the lumnare group s swthed on agan. Threshold Value above whh the lumnare group s swthed off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whh the threshold must be exeeded n order for the lumnare group to be swthed off by the lght sensor. Value range: mn Table 113: Lght sensor onfguraton optons n dret master mode 218

219 Confguraton Settng the response of the DALI MSensor 02 to a sene reall In the detal vew of the DALI MSensor 02 ts response to a sene reall an be set. A response an be onfgured for eah of the 16 senes. The followng onfguraton optons are avalable: Confguraton Lght sensor Moton sensor automat The lumnare group assgned to the lght sensor swthes to the presene value. Ambent lght ontrol s enabled. Moton sensor dsabled: the moton sensor s enabled. The run-on tme starts over. Moton sensor enabled: the run-on tme starts over. stat The lumnare group assgned to the lght sensor swthes to the ntensty set n the ontrol gear for the sene n queston. If ambent lght ontrol was enabled before the sene was realled, t s temporarly dsabled. Moton sensor dsabled: the moton sensor s enabled. The run-on tme starts over. Moton sensor enabled: the run-on tme starts over. off The lumnare group assgned to the lght sensor s swthed off. The moton sensor swthes to status Dead tme (manual off) n progress. MASK The lght sensor gnores the sene reall. The moton sensor gnores the sene reall. Table 114: Response of the DALI MSensor 02 to a sene reall If the response to a sene reall s set to automat, off or MASK, the MASK value for ths sene must be set for all ontrol gear elements. Informaton on how senes are onfgured an be found n Seton DALI ontrol gear > Confguraton va the detal vew 40. Advaned settngs n dret master mode The followng advaned settngs are dsplayed for the lght sensor n dret master mode f ambent lght ontrol has been enabled. Advaned settngs The "Maxmum level" ommand starts ambent lght ontrol. Desrpton Chekbox dsabled: after the Maxmum level ommand s reeved, the lumnare group swthes to the maxmum level untl the run-on tme for the moton sensor has expred. If ambent lght ontrol was enabled before the Maxmum level ommand was reeved, t s temporarly dsabled. 219

220 Confguraton Chekbox enabled: after the Maxmum level ommand s reeved, the lumnare group swthes to the maxmum level. Ambent lght ontrol s started. The "Brghten" and "Dm" ommands temporarly hange the desred value for ambent lght ontrol. Chekbox dsabled: after a Brghten or Dm ommand s reeved, the lumnare group s smoothly adjusted aordngly. The desred value for ambent lght ontrol remans unhanged. Chekbox enabled: after a Brghten or Dm ommand s reeved, the lumnare group s smoothly adjusted aordngly. The measured llumnane on the DALI MSensor after smooth adjustment s temporarly saved as a new desred value for ambent lght ontrol. The desred value s reset one the run-on tme has expred or an OFF ommand s reeved. Table 115: Lght sensor advaned settngs n dret master mode To apply the hanged values to the lght sensor, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 220

221 Confguraton Referene deve The lght sensor requres a referene deve n order to exatly alulate the swth-on level for ambent lght ontrol. A referene deve s a DALI ontrol gear element loated n the same group as the DALI MSensor. The masterconfigurator automatally adds the frst DALI ontrol gear element loated n the same group as the DALI MSensor as a referene deve. If another DALI ontrol gear element s desred for use as a referene deve, remove the referene deve and add the desred DALI ontrol gear element agan. Removng a referene deve Requrement: Advaned settngs enabled. Clk Remove n the detal vew of the lght sensor. The referene deve s removed. Addng a referene deve Requrement: DALI MSensor has been assgned to a DALI group. 1. In the DALI deve tree dagram, lk on the deve to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the deve to the desred group. (Drag & Drop) The deve s removed from the group n whh t was prevously loated and s added to the desred group. The address of the DALI ontrol gear element s automatally dsplayed as the referene deve n the DALI MSensor. If the DALI ontrol gear element used as a referene deve by the DALI MSensor (or the DALI MSensor tself) s deleted from the DALI group, the nformaton for the referene deve n the DALI MSensor s also deleted. For Referene deve the followng appears: none. 221

222 Confguraton Moton sensor The moton sensor supports two operatng modes: Dret master mode Slave mode: the moton sensor annot be onfgured n ths operatng mode. The moton sensor just responds to ommands from the master deve. More nformaton on these operatng modes an be found n Seton DALI MSensor Dret master mode Status n dret master mode The followng status nformaton s dsplayed for the moton sensor n dret master mode: Status Desrpton Moton sensor Indates the status of the moton sensor: Off Lghtng at presene value 222

223 Confguraton Lghtng at presene value, run-on tme n progress Lghtng fadng to absene value, fade tme n progress Lghtng at absene value Lghtng at absene value, swth-off delay n progress Dead tme (manual off) n progress Update status automatally Indates whether the moton sensor status s updated automatally. Table 116: Moton sensor status nformaton n dret master mode Confguraton optons n dret master mode The followng onfguraton optons are dsplayed for the moton sensor n dret master mode: Confguraton opton Desrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatally swthed on and off dependng on whether presene s deteted. (fatory settng) enabled (only OFF): the moton sensor swthes the lghtng off only. It must be swthed on manually. dsabled: the moton sensor s dsabled. The lghtng must be swthed on and off manually. : The never OFF funton s mplemented as follows: 1. Selet the enabled operatng mode. 2. Selet swth-off delay never OFF. Power on behavour Indates how the moton sensor wll reat after falure of the DALI power supply: no aton last state maxmum level off presene value: speally alulated value for ambent lght ontrol. Fade-n tme Tme requred to reah the presene value. Value range: fast s Presene value Value to whh the lumnare group swthes when presene s deteted n the room. The presene value ontrol depends on how the lght sensor s onfgured. ambent lght-ontrolled: If ambent lght ontrol s enabled for the lght sensor, the presene value s regulated based on ambent lght levels. fxed: If ambent lght ontrol s dsabled for the lght sensor, a value an be set as a perentage between 0 100%. 223

224 Confguraton Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. Value range: 30 s 60 mn nfnte: the run-on tme ontnues wthout end. Ths means that the lumnares reman at the defned presene value (ambent lght-ontrolled or fxed). The fade tme does not start. Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Value range: fast s Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Value range: 0 s 60 mn never OFF: the lghtng remans at the absene value untl further movement s deteted and the moton sensor swthes to the presene value. The lumnare group s never swthed off by the moton sensor. Absene value Level to whh the lumnare group swthes durng the swth-off delay. Fade-out tme Tme requred to dm off from the absene value. Value range: fast s Dead tme (manual off) Tme started by manually swthng off the lghtng va the momentary-aton swth or the remote ontrol and durng whh the moton sensor s dsabled. If movement s deteted n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s deteted n the room, the moton sensor s enabled agan. Value range: 0 s 20 mn Table 117: Moton sensor onfguraton optons n dret master mode 224

225 Confguraton Overvew of onfguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swth-off delay 5) Fade-out tme A) Presene value B) Absene value Advaned settngs n dret master mode The followng advaned settngs are dsplayed for the moton sensor n dret master mode: Advaned settngs Desrpton Set response to presene n other groups Ths settng determnes how the moton sensor responds when presene s deteted n another group. Four groups n total an be onfgured. MASK: the DALI MSensor 02 gnores the presene deteted n another group (fatory settng). Presene value: the lumnare group assgned to the DALI MSensor 02 swthes to the presene value. Absene value: the lumnare group assgned to the DALI MSensor 02 swthes to the absene value. Exepton: f the lumnares are already at the presene value, they retan ths settng. Table 118: Moton sensor advaned settngs n dret master mode To apply the hanged values to the moton sensor, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 225

226 Confguraton Remote ontrol The remote ontrol supports two operatng modes: Dret master mode Slave mode: the remote ontrol annot be onfgured n ths operatng mode. The remote ontrol has no funton. More nformaton on these operatng modes an be found n Seton DALI MSensor Dret master mode Confguraton optons n dret master mode The followng deve nformaton s dsplayed for the remote ontrol n dret master mode: Confguraton opton Desrpton Confguraton Confguraton of the remote ontrol: Inatve: the keys of the remote ontrol are natve. Fatory settngs: the remote ontrol keys are assgned wth default settngs. The lumnare group s set usng the rotary swth n the battery ompartment of the remote 226

227 Confguraton ontrol. user-defned: the keys of the remote ontrol an be assgned to seleted funtons. Table 119: Remote ontrol onfguraton optons n dret master mode Parametersng the key assgnment Wth the user-defned onfguraton, the key assgnment of the remote ontrol an be parametersed by the user. If key assgnment s ustomsed, the group assgnment as defned by the rotary swth n the battery ompartment of the remote ontrol s gnored. The ommands only apply to the lumnare group set dretly on the rotary swth on the DALI MSensor 02. Dependng on the key, varous onfguraton optons are avalable: On Off On/Off Brghten Dm Sene 0 15 Intensty 1 100% Ambent lght ontrol Reserved: ths opton s reserved for future funtonal enhanements and urrently has no funton. To apply the hanged values to the remote ontrol, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 227

228 Confguraton Speal notes: DALI MSensor deves verson 2.0 and lower The behavour of the DALI MSensor 02 s to some extent sgnfantly dfferent from that of prevous versons (V1.5 or lower). Group assgnment of dfferent generatons of DALI MSensor deves DALI MSensor 02 deves and DALI MSensor deves verson 1.5 or lower annot be assgned to the same group, as these versons work from dfferent group onepts. Replang a faulty DALI MSensor (V1.5 or lower) A faulty DALI MSensor V1.5 or lower an only be replaed by a DALI MSensor 02 to a lmted extent. Further nformaton an be found n the produt manual for the DALI MSensor 02. Resettng the frmware verson of DALI MSensor 02 deves to verson 1.5 If a faulty DALI MSensor 1.5 annot be replaed, a DALI MSensor 02 an be reset to frmware verson 1.5 usng the masterconfigurator. More nformaton on the frmware update an be found here The frmware of all DALI MSensors onneted to the DALI ontrol lne wll be updated. If only one deve needs to be updated, ths deve must be updated on a separate DALI ontrol lne. The deve must be readdressed after the frmware has been updated. 228

229 Confguraton DALI MSensor (verson 1.5 and 1.7) DALI MSensors are represented by four dfferent symbols n the DALI deve tree. The DALI MSensor onssts nternally of three deve lasses, whh are lsted ndvdually n the DALI deve tree dagram: Lght sensor: A detaled desrpton of the lght sensor an be found n Seton DALI MSensor (V1.5 and 1.7) > Lght sensor 230. Moton sensor: A detaled desrpton of the moton sensor an be found n Seton DALI MSensor (V1.5 and 1.7) > Moton sensor 233. Remote ontrol: A detaled desrpton of the remote ontrol an be found n Seton DALI MSensor (V1.5 and 1.7) > Remote ontrol 237. Group onept Every DALI MSensor has two groups: Lumnare group: all deves n ths group are ontrolled by the DALI MSensor. Sensor group: a group va whh the DALI MSensor an be nfluened. The next hghest group s automatally assgned as the sensor group. The followng groups are also dsplayed f advaned settngs have been enabled: Lght sensor group: ed group (eg) ontanng the lght sensor. Moton sensor group: ed group (eg) ontanng the moton sensor. Remote ontrol group: ed group (eg) ontanng the remote ontrol. Effetve range The DALI MSensor ontrols ether all deves (broadast) or one DALI group: Assgnment va the rotary swth The effetve range of the DALI MSensor s set usng the rotary swth on the bak of the sensor. All ontrol gear elements n the set effetve range are ontrolled by the DALI MSensor. The next hghest group s automatally assgned as the sensor group. 229

230 Confguraton Assgnment va the masterconfigurator When the DALI MSensor s not assgned to a group n the DALI deve tree dagram, t ontrols the lumnare group set usng the rotary swth on the bak of the sensor. It must be assgned to a group to ontrol an ndvdual group. 1. In the DALI deve tree dagram, lk on the DALI MSensor. 2. Hold down the left mouse button. 3. Drag the DALI MSensor to the desred lumnare group. The DALI MSensor s removed from the ndvdual (non-grouped) seton of the DALI deve tree dagram and s added to the desred lumnare group. The next hghest group s automatally assgned as the sensor group. The poston of the rotary swth on the bak of the DALI MSensor s gnored. If the group assgnment n the masterconfigurator s undone, the rotary swth poston wll be atve agan. Lght sensor Status 230

231 Confguraton The followng status nformaton s dsplayed for the lght sensor: Status Desrpton Illumnane Illumnane urrently measured at the lght sensor. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Update status automatally Indates whether the lght sensor status s updated automatally. Ambent lght ontrol Indates the status of ambent lght ontrol for the lght sensor. enabled: ambent lght ontrol s enabled. temporarly dsabled: ambent lght ontrol has been temporarly dsabled manually by the user. dsabled: ambent lght ontrol s dsabled. unknown: there s urrently no onneton to the lght sensor. Referene deve Indates the DALI ontrol gear used as a referene for alulatng the swth-on level durng ambent lght ontrol. If no referene deve has been assgned to the lght sensor, no deve wll be dsplayed. : Seton Referene deve referene deve s assgned. 232 explans how a Table 120: Lght sensor status nformaton Confguraton optons The followng onfguraton optons are dsplayed for the lght sensor: Confguraton opton Desrpton Ambent lght ontrol Ambent lght ontrol an be enabled or dsabled. Desred value Value used by the lght sensor to regulate the ontrol gear. On aount of the room ondtons and the nstallaton heght, the llumnane n the workspae may, however, be three to four tmes hgher. Value range: lx Control speed Speed at whh the ontrol gear reahes the desred value. Value range: nrements 0 7, wth 0 beng the slowest and 7 the fastest. 231

232 Confguraton Swth-on level Level when the lghtng s swthed on. Ambent lght ontrol starts from ths value. Mnmum level Maxmum level alulated: the swth-on level for ambent lght ontrol s speally alulated so that t s as lose to the desred value as possble. Enable dmmng off (brght out) Chekbox enabled: f the measured llumnane exeeds the defned threshold for a perod longer than the set delay tme, the lumnare group s swthed off by the lght sensor even f moton s deteted n the room. As soon as the measured llumnane falls below the desred value, the lumnare group s swthed on agan. Threshold Value above whh the lumnare group s swthed off by the lght sensor. Value range: % of the desred value Delay tme Tme durng whh the threshold must be exeeded n order for the lumnare group to be swthed off by the lght sensor. Value range: mn Table 121: Lght sensor onfguraton optons To apply the hanged values to the lght sensor, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. Referene deve The lght sensor requres a referene deve n order to exatly alulate the swth-on level for ambent lght ontrol. A referene deve s a DALI ontrol gear element loated n the same group as the DALI MSensor. The masterconfigurator automatally adds the frst DALI ontrol gear element loated n the same group as the DALI MSensor as a referene deve. If another DALI ontrol gear element s desred for use as a referene deve, remove the referene deve and add the desred DALI ontrol gear element agan. Removng a referene deve Requrement: Advaned settngs enabled. Clk Remove n the detal vew of the lght sensor. The referene deve s removed. 232

233 Confguraton Addng a referene deve Requrement: DALI MSensor has been assgned to a DALI group. 1. In the DALI deve tree dagram, lk on the deve to be assgned to a group. 2. Hold down the left mouse button. 3. Drag the deve to the desred group. (Drag & Drop) The deve s removed from the group n whh t was prevously loated and s added to the desred group. The address of the DALI ontrol gear element s automatally dsplayed as the referene deve n the DALI MSensor. If the DALI ontrol gear element used as a referene deve by the DALI MSensor (or the DALI MSensor tself) s deleted from the DALI group, the nformaton for the referene deve n the DALI MSensor s also deleted. For Referene deve the followng appears: none. Moton sensor Status The followng status nformaton s dsplayed for the moton sensor: 233

234 Confguraton Status Desrpton Moton sensor Indates the status of the moton sensor: Off Lghtng at presene value Lghtng at presene value, run-on tme n progress Lghtng fadng to absene value, fade tme n progress Lghtng at absene value Lghtng at absene value, swth-off delay n progress Dead tme (manual off) n progress Update status automatally Indates whether the moton sensor status s updated automatally. Table 122: Moton sensor status nformaton 234

235 Confguraton Confguraton optons The followng onfguraton optons are dsplayed for the moton sensor: Confguraton opton Desrpton Operatng mode Moton sensor operatng mode: enabled: the lghtng s automatally swthed on and off dependng on whether presene s deteted. (fatory settng) enabled (only OFF): the moton sensor swthes the lghtng off only. It must be swthed on manually. dsabled: the moton sensor s dsabled. The lghtng must be swthed on and off manually. : The never OFF funton s mplemented as follows: 1. Selet the enabled operatng mode. 2. Selet swth-off delay never OFF. Power on behavour Indates how the moton sensor wll reat after falure of the DALI power supply: no aton last state maxmum level off presene value: speally alulated value for ambent lght ontrol. Fade-n tme Tme requred to reah the presene value. Value range: fast s Presene value Value to whh the lumnare group swthes when presene s deteted n the room. The presene value ontrol depends on how the lght sensor s onfgured. ambent lght-ontrolled: If ambent lght ontrol s enabled for the lght sensor, the presene value s regulated based on ambent lght levels. fxed: If ambent lght ontrol s dsabled for the lght sensor, a value an be set as a perentage between 0 100%. Run-on tme A tme startng from the last deteted movement n the room; when the run-on tme expres, the fade tme begns. If further movement s deteted durng the run-on tme, t starts over agan. Value range: 30 s 60 mn nfnte: the run-on tme ontnues wthout end. Ths means that the lumnares reman at the defned presene value (ambent lght-ontrolled or fxed). The fade tme does not start. 235

236 Confguraton Fade tme Tme durng whh the lghtng s smoothly adjusted to the absene value. Value range: fast s Swth-off delay Tme for whh the absene value s mantaned f no movement s deteted. Value range: 0 s 60 mn never OFF: the lghtng remans at the absene value untl further movement s deteted and the moton sensor swthes to the presene value. The lumnare group s never swthed off by the moton sensor. Absene value Level to whh the lumnare group swthes durng the swth-off delay. Fade-out tme Tme requred to dm off from the absene value. Value range: fast s Dead tme (manual off) Tme started by manually swthng off the lghtng va the momentary-aton swth or the remote ontrol and durng whh the moton sensor s dsabled. If movement s deteted n the room durng ths tme, the dead tme starts over agan. If at the end of the dead tme no more movement s deteted n the room, the moton sensor s enabled agan. Value range: 0 s 20 mn Table 123: Moton sensor onfguraton optons Overvew of onfguraton optons The followng fgure shows a summary of the ndvdual parameters. 1) Fade-n tme 2) Run-on tme 3) Fade tme 4) Swth-off delay 5) Fade-out tme A) Presene value B) Absene value 236

237 Confguraton To apply the hanged values to the moton sensor, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. Remote ontrol Confguraton optons The followng deve nformaton s dsplayed for the remote ontrol: Confguraton opton Desrpton Confguraton Confguraton of the remote ontrol: Inatve: the keys of the remote ontrol are natve. Fatory settngs: the remote ontrol keys are assgned wth default settngs. The lumnare group s set usng the rotary swth n the battery ompartment of the remote ontrol. user-defned: the keys of the remote ontrol an be assgned to seleted funtons. Table 124: Remote ontrol onfguraton optons 237

238 Confguraton Parametersng the key assgnment Wth the user-defned onfguraton, the key assgnment of the remote ontrol an be parametersed by the user. If key assgnment s ustomsed, the group assgnment as defned by the rotary swth n the battery ompartment of the remote ontrol s gnored. The ommands only apply to the lumnare group set dretly on the rotary swth on the DALI MSensor. Dependng on the key, varous onfguraton optons are avalable: On Off On/Off Brghten Dm Sene 0 15 Intensty 1 100% Ambent lght ontrol Reserved: ths opton s reserved for future funtonal enhanements and urrently has no funton. To apply the hanged values to the remote ontrol, lk on save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 238

239 Confguraton DALI MSensor (verson 1.3) For DALI MSensors wth frmware verson 1.3, there are a few small dfferenes ompared to DALI MSensors wth verson 1.4 or hgher. Ambent lght ontrol: enabled/dsabled Ths parameter s not supported by a DALI MSensor wth a frmware verson lower than 1.4. In the masterconfigurator software, the parameter appears greyed out. Ambent lght ontrol an be dsabled as follows: 1. Open the detal vew for the moton sensor. 2. Under "Presene value" selet the fxed rado button. 3. Enter the perentage for the presene value. 4. Clk on save. Ambent lght ontrol s dsabled. Status There are only two status messages: enabled: ambent lght ontrol s enabled. temporarly dsabled: ambent lght ontrol s dsabled usng the DALI RC remote ontrol or s dsabled temporarly by the user manually. Dead tme (manual off) The lowest value whh an be set for the dead tme s 30 seonds. 239

240 Confguraton 8.6 DALI TOUCHPANEL The DALI TOUCHPANEL s represented n the DALI deve tree dagram by the on and the name DALI Touh. When addressng, the DALI TOUCHPANEL s gven an ed address (ea) and an be onfgured n the detal vew usng ths address. Deve nformaton The followng deve nformaton s dsplayed n the header: Deve nformaton Desrpton Name Dsplays the name of the deve. Frmware verson Dsplays the frmware verson of the deve. Table 125: Deve nformaton Confguraton The followng onfguraton optons are avalable for the DALI TOUCHPANEL: User-defned: For a detaled desrpton of the user-defned onfguraton, see Seton User-defned onfguraton 241. Tunable Whte: For a detaled desrpton of the Tunable Whte onfguraton, see Seton Tunable Whte Fatory settngs: For a detaled desrpton of the Fatory settngs, see Seton Fatory settngs

241 Confguraton User-defned onfguraton The user-defned onfguraton an be enabled usng the masterconfigurator. The 6 keys on the DALI TOUCHPANEL an be onfgured ndvdually. Settng the user-defned onfguraton 1. Enable the user-defned rado button. A message appears, promptng for onfrmaton that the deve onfguraton should be modfed. Ths overwrtes the exstng settngs. 2. Confrm the aton by lkng on Yes. 3. Selet Key 1. Current onfguraton of Key 1 s loaded. The followng onfguratons are performed for the seleted key. 4. From the Target dropdown lst, selet the destnaton address to whh the ommand s to apply: All, group (0 15) or address (0 63). 5. Selet a response from the Set response to key press dropdown lst. For a prese desrpton of possble responses see Response to key press 243 table. 241

242 Confguraton 6. In order to store a DALI ommand for ommand X and ommand Y, enable the DALI ommand (ndret) rado button. -orin order to store an ntensty for ommand X and ommand Y, enable the Intensty (DAP) rado button. Command X and ommand Y represent varables that must be stored for the ommands. You an ether store DALI ommands or an ntensty. 7. Confgure ommand X and ommand Y. DALI ommand (ndret) Selet a DALI ommand n the dropdown lst. Intensty (DAP) Enter the value for the ntensty. For a prese desrpton of the DALI ommands, see Seton DALI ommands In order to nvoke ommand X wth a fade tme, n the ommand X group feld, enable the Fade Tme hekbox and selet a fade tme n the dropdown lst. 9. In order to nvoke ommand Y wth a fade tme, n the ommand Y group feld, enable the Fade Tme hekbox and selet a fade tme n the dropdown lst. 10.Clk on Save. The onfguraton s saved n the DALI TOUCHPANEL. 11.Repeat steps 3 to 10 for keys

243 Confguraton The saved onfguraton an now be tested dretly n the DALI nstallaton. Response to key press bref = toggle between ommand X and ommand Y, long = s gnored Desrpton When the key s pressed brefly, ommand X and ommand Y are output alternately. A long key press has no effet. Adjustable parameters: Command X Command Y bref = s gnored, long = brghten A bref key press has no effet. In the ase of a long key press the ommand that s output depends on the status of the lghtng: If the lghtng was prevously swthed off, the mnmum level s sent. If the lghtng was prevously swthed on, the lghtng s brghtened. bref = ommand X, long = brghten Command X and ommand Y do not have to be defned. Brefly pressng the key outputs the seleted ommand X. In the ase of a long key press the ommand that s output depends on the status of the lghtng: If the lghtng was prevously swthed off, the mnmum level s sent. If the lghtng was prevously swthed on, the lghtng s brghtened. Adjustable parameters: Command X bref = s gnored, long = dm A bref key press has no effet. In the ase of a long key press the lghtng s dmmed. bref = ommand Y, long = dm Command X and ommand Y do not have to be defned. Brefly pressng the key outputs the seleted ommand Y. In the ase of a long key press the lghtng s dmmed. Adjustable parameters: Command Y 243

244 Confguraton bref = s gnored, long = toggle between brghten and dm A bref key press has no effet. In the ase of a long key press the lghtng s brghtened and dmmed alternately. bref = toggle between ommand X and ommand Y, long = toggle between brghten and dm Command X and ommand Y do not have to be defned. When the key s pressed brefly, ommand X and ommand Y are output alternately. In the ase of a long key press the lghtng s brghtened and dmmed alternately. Adjustable parameters: Command X Command Y Table 126: Summary of response to key press n ase of DALI TOUCHPANEL 244

245 Confguraton Tunable Whte The Tunable Whte onfguraton an be enabled usng the masterconfigurator. "Tunable Whte" desrbes the opton to dynamally hange the lght of an LED lumnare n the whte lght range. The olour temperature of Tunable Whte lumnares an be hanged n the whte lght range from 2700 to 6500 kelvn. Default settngs for ntensty and olour temperature are assgned to the keys of the DALI TOUCHPANEL. The masterconfigurator software an be used to set the destnaton address and two fade tmes, one for swthng the lumnares on and one for swthng them off. As soon as a fade tme has been set for swthng the lumnares on or off, a fade tme of 1 s s automatally stored for dmmng. Settng the "Tunable Whte" onfguraton Requrement: Tunable Whte lumnares are n use. 1. Enable the Tunable Whte rado button. A message appears, promptng for onfrmaton that the deve onfguraton should be modfed. Ths overwrtes the exstng settngs. 2. Confrm the aton by lkng on Yes. 3. From the Target dropdown lst, selet the destnaton address that the DALI TOUCHPANEL s to ontrol: All, group (0 15) or address (0 63). 245

246 Confguraton 4. In order to store a fade tme for swthng on, n the ommand X group feld, enable the Fade Tme hekbox and selet a fade tme n the dropdown lst. 5. In order to store a fade tme for swthng off, n the ommand Y group feld, enable the Fade Tme hekbox and selet a fade tme n the dropdown lst. 6. Clk on Save. The onfguraton s saved n the DALI TOUCHPANEL. The saved onfguraton an now be tested dretly n the DALI nstallaton. 246

247 Confguraton Fatory settngs The keys of the DALI TOUCHPANEL are assgned as follows by default. Key 1: Go to sene 1 Key 2: Up Key 3: Go to sene 2 Key 4: Down Key 5: Go to sene 3 Key 6: Off When the fatory settngs are stored n the DALI TOUCHPANEL, a dagram showng the key assgnments s dsplayed n the masterconfigurator. The fatory settngs annot be modfed. In order to set the DALI TOUCHPANEL up as user defned, enable the user-defned onfguraton. For a detaled desrpton of the user-defned onfguraton, see Seton Userdefned onfguraton 241. Restorng the fatory settngs 1. Clk on Fatory settngs. A message appears, promptng for onfrmaton that the deve should be reset to ts fatory settngs. 2. Confrm the aton by lkng on Yes. The deve s reset to ts fatory settngs. 247

248 Confguraton 8.7 DALI PS2 Standby The DALI PS2 Standby s a DALI power supply wth 240 ma nomnal urrent for DALI ontrol gear and DALI ontrol unts whh do not have ther own power supply. To redue the standby losses, the bult-n relay dsonnets the ontrol gear from the mans as soon as all the lumnares have been swthed off. Ths ensures that the power loss s redued to a mnmum. The DALI PS2 Standby s represented n the DALI deve tree dagram by the vew. on and s onfgured n the detal Confguraton opton Desrpton Standby/Atve Indates the status of the DALI PS2 Standby: Standby Atve swth to: Standby swth to: Atve Ths button allows the user to swth between the Atve and Standby modes. Update status automatally The status s updated automatally. Swth-off delay Tme that starts runnng as soon as t s deteted that all the DALI ontrol gear has been swthed off, after whh the unt swthes to standby mode. Value range: 1 mn 2 d Standby mode dsabled The DALI PS2 Standby behaves lke a onventonal DALI power supply nstead of swthng to standby mode. 248

249 Confguraton Lght level poll nterval Tme nterval n whh the ontrol gear s polled about the lght level. Value range: 1 mn 23 h Ballast power up delay Tme durng whh the frst 10 ommands that are sent whle the eletron ballasts are powerng up wll be buffered. At the end of the eletron ballast swth-on delay, the ommands are sent from the power supply to the eletron ballasts. Ths ensures that no ommands are lost whle the eletron ballasts are startng up. Command buffer Number of ommands that are buffered whle the eletron ballasts are startng up. Value range: 1 10 ommands Relay state nverted dsabled: f all the deves are swthed off, the relay output s open. (fatory settng) enabled: f all the deves are swthed off, the relay output s losed. DALI LED nverted enabled: LED llumnates only f there s ommunaton on the DALI ontrol lne. (fatory settng) dsabled: LED llumnates when the power supply s ready for operaton. If there s ommunaton on the DALI ontrol lne, the LED wll go out brefly. Standby LED nverted dsabled: LED llumnates when standby mode s enabled. (fatory settng) enabled: LED llumnates when standby mode s dsabled. Update/read urrent values If the hekbox s seleted, the urrent values of the voltage (V) and of the flowng supply urrent (ma) are dsplayed. Table 127: Confguraton optons for DALI PS2 Standby n the detal vew To apply the hanged values to the DALI PS 2 Standby, lk on Save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 249

250 Confguraton 8.8 DALI-Somfy anmeo Interfae The DALI Somfy anmeo nterfae s represented n the DALI deve tree dagram by the the detal vew. on and s onfgured n The DALI Somfy anmeo nterfae s an nterfae module wth four addresses. Wth eah of these addresses t s possble to ontrol one of the four motors of the anmeo IB+ motor ontroller. Eah address of the DALI Somfy anmeo nterfae appears ndvdually n the deve tree dagram. Confguraton opton Desrpton Atual poston of blnd Indates the atual poston (0 100%) and the atual angle (0 200%) of the blnd. Ergonoms Determnes the behavour of the blnd durng tltng, when one of the followng ommands s sent: Off, Down, Reall mn US: moves to the lower end poston EU: makes a small postve angle movement Up, On and step up, Reall max US: moves to the upper end poston EU: makes a small negatve angle movement Sene assgnment Confgure senes Value range: Poston: 0 100% Tlt: 0 200% MASK: the blnds n ths group retan ther urrent poston when the respetve sene s alled up. Table 128: Confguraton optons for the DALI Somfy anmeo nterfae n the detal vew Before senes an be set or realled for the blnds, the runnng and tltng tmes must be set n the Somfy anmeo motor ontroller. 250

251 Confguraton To apply the new values to the DALI Somfy anmeo nterfae, lk on Save. The saved onfguraton an now be tested dretly n the DALI nstallaton. 251

252 Confguraton 8.9 Quk test The onfguraton of the ndvdual ontrol gear elements an be tested n the Quk test pop-up wndow. Intensty Senes DALI ommands xy-oordnates Colour temperature 255 Sendng urrent ntensty 1. Set the value usng the slder. The desred value s dsplayed as a DALI value n the tool tp wndow. 2. Clk Send. The value wll be sent to the ontrol gear and realled wth the set fade tme. The urrent ntensty s dsplayed to the left of the slder. The seleted value must be between the Mnmum level and the Maxmum level. 252

253 Confguraton Reallng sene X Clk Sene X (0 15). Sene X (0 15) s realled. The defned fade tme wll be used. Sendng a ommand The followng DALI ommands an be tested: DALI ommand Desrpton Mnmum level The mnmum level s realled mmedately wthout any fade tme. Maxmum level The maxmum level s realled mmedately wthout any fade tme. Dm The ntensty s redued by the steps defned n the fade rate. When the lghtng reahes the set mnmum level, t remans at ths level. : As long as the Dm button s pressed, the Dm ommand wll be sent repeatedly. Brghten The ntensty s nreased by the steps defned n the fade rate. When the lghtng reahes the set maxmum level, t remans at ths level. : As long as the Brghten button s pressed, the Brghten ommand wll be sent repeatedly. Step darker The ntensty s redued by one step. Step brghter The ntensty s nreased by one step. Step darker - Off If the lghtng s swthed on, the ntensty s redued by one step. If the lghtng reahes the mnmum level, t s swthed off. Mn. level + step brghter If the lghtng s swthed off, the mnmum level s realled. If the lghtng s swthed on, the ntensty s nreased by one step. Off The lghtng s swthed off mmedately wthout any fade tme. Table 129: DALI ommands The DALI ommands Step darker, Step brghter, Step darker - Off and Mn. level + step brghter are only vsble when the advaned settngs are enabled. Informaton on how to enable the advaned settngs an be found n Seton Atve wndow

254 Confguraton Sendng xy-oordnates 1. Set the value usng the slder. -orclk the button for a pre-defned olour temperature, e.g. Cheese. 2. Clk Send. The value wll be sent to the ontrol gear and realled wth the set fade tme. 254

255 Confguraton Sendng the ntensty or olour temperature 1. Set the value usng the slder. -orenter the value n the nput feld (only ntensty) -orclk the button for a pre-defned olour temperature (only olour temperature) 2. Clk Send. The value wll be sent to the ontrol gear and realled wth the set fade tme. 255

256 Tools 9 Tools The masterconfigurator software provdes the followng tools: Command admnstrator Control gear wzard Frmware update Command admnstrator The Command admnstrator enables the advaned DALI user to send DALI and DSI ommands dretly to all ontrol gear onneted to the ontrol lne, to an ndvdual group or an ndvdual address, and also to work wth ommand sequenes DALI ommands Ths funton of the ommand admnstrator allows the user to send DALI ommands to all ontrol gear onneted to the ontrol lne, to an ndvdual group or to an ndvdual address. Sendng a DALI ommand Requrement: Knowledge of the DALI ommand set. 1. Selet Tools > Command admnstrator. The Command admnstrator pop-up wndow appears. 2. Clk on the DALI ommands tab. 3. Selet rado button all, group or address. 4. Enter the number of the ommand. -orselet the desred ommand from the drop-down lst. 256

257 Tools 5. Enter the value n demal (de) or hexademal (hex). -orset the value usng the slder. 6. In order to repeat the ommand one, selet the hekbox Repeat ommand one. 7. In order to repeat the ommand every 500 ms, selet the hekbox Repeat ommand every 500 ms. 8. Clk on Send ommand. The DALI ommand wll be sent n aordane wth the seleted optons. The response appears mmedately n the Response feld DSI ommands Ths funton of the Command admnstrator allows the user to send DSI ommands to all ontrol gear onneted to the ontrol lne. To do so, frst send a value and then the desred ommand. Sendng a value Requrement: Knowledge of the DSI ommand set. 1. Selet Tools > Command admnstrator. The Command admnstrator pop-up wndow appears. 2. Clk on the DSI ommands tab. 3. Enter the ntensty n demal (de) or hexademal (hex). -orset the ntensty usng the slder. 4. Clk on Send value. The value wll be sent to all ontrol gear onneted to the ontrol lne. 257

258 Tools Sendng a ommand Requrements: Knowledge of the DSI ommand set. Command admnstrator pop-up wndow and DSI ommands tab open. 1. Selet the desred ommand from the Command drop-down lst. 2. In order to repeat the ommand every 500 ms, selet the hekbox Repeat ommand every 500 ms. 3. Clk on Send ommand. The DSI ommand wll be sent to all ontrol gear onneted to the ontrol lne Command sequene Ths funton of the Command admnstrator allows the user to send a sequene of DALI or DSI ommands. Create ommand sequene Requrement: Knowledge of the DALI and DSI ommand sets. 1. Selet Tools > Command admnstrator. The Command admnstrator pop-up wndow appears. 2. Clk on the Command sequene tab. 258

259 Tools 3. Clk on Add ommand. The Add ommand pop-up wndow appears. 4. Defne the DALI or DSI ommand va the nput felds, lsts and rado buttons. 5. Optonally, a delay tme n mllseonds an be defned. 6. Clk on Add. The DALI or DSI ommand s added to the ommand sequene. Further funtons Desrpton (Fle) New Delete all ommands. (Fle) Open Open a prevously saved ommand sequene. (Fle) Save Save the urrent ommand sequene n a fle wth the extenson *.ot. (Command) Add Add a new ommand to the ommand sequene. (Command) Change Change the seleted ommand. (Command) UP Move seleted ommand up. (Command) DOWN Move seleted ommand down. (Command) Delete Delete the seleted ommand. (Test) Start Start the ommand sequene. All ommands are sent to the defned destnaton address (all, group, ndvdual address) n the spefed order. (Test) Stop Stop the ommand sequene. (Test) Infnte loop Repeat the ommand sequene endlessly. (Test) Sngle step One ommand at a tme s sent to the deves or groups n the spefed order. Table 130: Command admnstrator - further funtons 259

260 Tools 9.2 Control gear wzard The ontrol gear wzard an be used to enable and onfgure ontrol gear funtons and parameters. The onfguratons are sent to all ontrol gear onneted to the DALI ontrol lne. Funtons and parameters Desrpton Interfae mode Selet an nterfae operatng mode. orrdorfunction (DALI V1) Carry out orrdor ontrol wth a smple moton sensor (see Seton Deve operatng mode DALI V1 52 ). orrdorfunction (DALI V2) Carry out orrdor ontrol wth a smple moton sensor (see Seton Deve operatng mode DALI V2 56 ). Deve onfguraton Set the epoweron level and dmmng/swthng parameters n DC mode. DC level Set the ntensty to whh the ballast should dm/brghten n DC mode. Compatblty settngs Parameterse the ballast so that ts settngs math those of the preedng generaton of deves. Ths funton s desgned for replang ballasts n exstng systems. Reset default settngs Delete all prevous settngs and reset to the defaults. Table 131: Control gear w zard funtons 260

261 Tools Adjustng the settngs requres extensve knowledge of the ontrol gear. For further detals on the ndvdual funtons of the ontrol gear wzard, please refer to the relevant deve doumentaton. In mxed settngs that use both DALI V1 and V2 DALI, values are automatally heked for bakward ompatblty and adapted, f neessary. Ths apples to e.g. the Fade-n tme and Fade tme, whh are dfferent for orrdorfunction and orrdorfunction2 (see Seton orrdorfunction parameters 55 und orrdorfunction 2 parameters 57 ). 9.3 Loalsaton wzard for DALI XC The loalsaton wzard for DALI XC an be used for tatle loaton of the ndvdual nputs of the DALI XC wth a double-lk. The loalsaton wzard reates a lst of loated deves. Ths lst an be used to note the assoated address and nput (T1 T4) n the addressng plan for eah momentary-aton swth or standard swth onneted to a DALI XC. Loatng momentary-aton swthes or standard swthes usng the loalsaton wzard 1. Selet menu tem Tools > Loalsaton wzard for DALI XC... The Loalsaton wzard for DALI XC pop-up wndow appears. 2. Double-lk one of the momentary-aton swthes or standard swthes onneted to a DALI XC. Conseutve numbers and ed addresses for the assoated DALI XC and the nput (T1 T4) of the momentaryaton swth or standard swth pressed are added to the lst. 3. Repeat step 2 for eah of the momentary-aton swthes or standard swthes onneted to a DALI XC. 4. the ed addresses and nputs n the addressng plan. To be able to ontnue to use the nformaton n a text edtng program, selet the ontent of ths pop-up wndow usng the mouse and then press CTRL + C to opy. 5. To delete the lst, lk Delete lst. Lst s deleted. 6. To ext the loalsaton wzard, lk Ext. Loalsaton wzard s losed. Lst s deleted. 261

262 Tools Confgurng loated momentary-aton swthes or standard swthes The loalsaton wzard for DALI XC always opens n a separate pop-up wndow. Ths wndow remans open untl you ext the loalsaton wzard. The wzard provdes the opton of onfgurng a loated momentary-aton swth or standard swth dretly. Requrements: Momentary-aton swth or standard swth has been loated n the loalsaton wzard for DALI XC. Loalsaton wzard for DALI XC s stopped but not losed. 1. To onfgure nput T3 of the DALI XC wth ed address 44, for example, lk the DALI XC wth ed address 44 n the DALI deve tree dagram. The bas onfguraton s opened n the detal vew. 2. Clk on the T3 tab. The T3 tab s opened n the detal vew. The loalsaton wzard remans open n a separate pop-up wndow. 3. Confgure nput T3. 4. Clk on Save. For a detaled desrpton of the onfguraton optons, see Seton DALI XC Frmware update The frmware of the followng deves an be updated usng the masterconfigurator software: DALI MSensor Frmware verson 1.5 or hgher annot be used for DALI MSensors wth versons 1.3 or 1.4, as these nvolve dfferent hardware. MSensor 5DPI 14 DALI Somfy anmeo nterfae DALI TOUCHPANEL Update frmware! Warnng The frmware of all DALI MSensors, MSensor 5DPI 14, DALI Somfy anmeo nterfaes or DALI TOUCHPANELS onneted to the DALI ontrol lne wll be updated. If the wrong frmware s loaded on a deve, ths may damage the deve. To avod loadng the wrong frmware on a deve make sure that the deves that need to be updated are onneted to a separate DALI ontrol lne and that no other deves are onneted to ths lne! 262

263 Tools The updated deves must be re-addressed. More nformaton on system extenson wth unaddressed deves an be found n Seton Addressng 21. The frmware update wll take around 20 mnutes. Durng the update, the power supply and onneton to the DALI ontrol lne must not be nterrupted. 1. In the menu bar, lk on Tools > Update frmware. The Update frmware pop-up wndow appears. 2. Clk on Open. 3. Selet desred *.hex fle. The namng of the *.hex fles follows a onsstent form, startng wth an aronym for the deve type, followed by the verson number. Examples: Fle name Deve type Verson no dalms150.hex DALI MSensor 150 MSensor_Mn_v100.hex MSensor 5DPI SomfyMoCo_V19.hex DALI Somfy anmeo nterfae 19 DALITouh2_V29.hex DALI TOUCHPANEL Choose deve for whh the frmware wll be updated: o MSensor rado button: Frmware wll be updated for all the DALI MSensors onneted to the DALI ontrol lne o MSensor 5DPI 14 rado button: Frmware wll be updated for all the MSensor 5DPI 14 onneted to the DALI ontrol lne o Somfy MoCo nterfae rado button: Frmware wll be updated for all the DALI Somfy anmeo nterfaes onneted to the DALI ontrol lne o DALI TOUCHPANEL rado button: Frmware wll be updated for all the DALI TOUCHPANEL onneted to the DALI ontrol lne 263

264 Tools 5. Clk on Start. A message appears whh states that the update wll take mnutes. 6. Confrm the message by lkng on Yes. The frmware of all DALI MSensors, MSensor 5DPI 14, DALI Somfy anmeo nterfaes or DALI TOUCHPANELS onneted to the DALI ontrol lne wll be updated. The Frmware update ompleted pop-up wndow appears. Ths ompletes the update. 264

265 Further omponents 10 Further omponents The programs DALI Montor and DALI BusServer are also nstalled wth the masterconfigurator software; these programs support the user when workng wth the masterconfigurator software. As DALI nterfae the DALI USB or the ready2man Programmer an be used. The DALI Montor an be aessed va the on n the Wndows task bar, the DALI BusServer va the on. For more nformaton about both programs, refer to the DALI Montor produt manual. The DALI Montor produt manual an be opened by lkng on the help on (queston mark symbol) n the menu bar of the DALI Montor (see sreenshot below). 265