LED Fixture Controller ELED1 Programming Guide

Transcription

1 LED Fxture Controller ELED1 Programmng Gude ELED1-AUN ELED1-AUS Copyrght 2018 Echoflex Solutons, Inc. All rghts reserved. Product nformaton and specfcaton detals subject to change Echoflex Solutons Queens Way, Unt #1, Squamsh, BC, V8B 0K8, Canada n echoflexsolutons.com n 8DC-5745 Rev 1.2 n 12/18

2 Range Confrmaton s an Echoflex Solutons Inc. Patented technology SmpleTap s a trademark of Echoflex Solutons, Inc. n Canada and other countres. All other trademarks, both marked and not marked, are the property of ther respectve owners. Echoflex ntends ths document, whether prnted or electronc, to be read n ts entrety.

3 Table of Contents Introducton Document Conventons...1 Overvew Rado Communcatons...2 Auto-Detect Dmmng...2 Dmmng Output...3 Near-Cross Relay Technology...3 Swtch Operaton... 4 Tmed Swtches...4 Occupancy Based Lghtng Applcatons... 5 Grace Tmer...5 Photo Inhbt...5 Dual Technology Occupancy Sensors...6 Occupancy Sensors and Partal-ON...6 Occupancy Sensors and Partal-OFF...6 Occupancy Sensors wth Swtches...6 Daylght Harvestng Applcaton... 7 Daylghtng Relay Control...7 Daylghtng Control Overrde...8 Closed Loop Daylghtng Control...8 Open Loop Control...9 Controller Button Interface LEARN button...10 CLEAR button...10 Power LED and Learn LED...11 Dsablng the User Interface LEDs...11 Confgurng the Controller Smple Tap Instructons Enable/Dsable the Repeater Functon...14

4 Enable/Dsable the Status Telegram...14 Enable/Dsable the Automatc Partal-ON feature...14 Set the Occupancy Sensor Auto-OFF tmer...15 Enable/Dsable Daylghtng Relay Control...16 Set the Closed Loop Daylghtng Set Pont...16 Set the Open Loop Daylghtng Set Pont...17 Appendx A LED Blnk Codes and Operaton Safety Standards Load Ratngs...19 Status Feedback Telegram... 20

5 Introducton Ths gude covers the Fxture Controller, model numbers ELED1-AUN and ELED1-AUS. The ELED1 s equpped wth a 902 MHz rado. The controller uses wreless technology to montor any room s envronment and provdes dmmng and swtchng control of an LED fxture. The controller ncludes Smple Tap technology whch allows nstallers and faclty operators to manage confguraton settngs wthout any tools. The ELED1 s a fxture controller desgned to ft wth today s vast number of LED lumnares provdng full-off wth relay and 0-10V dmmng. The controller provdes dmmng and swtchng control wth receved nput from a lnked sensor or swtch. As a lghtng controller, t operates lghts based on: ambent lght levels montored by a wreless photo sensor occupancy state montored by a wreless occupancy sensor swtch acton from a wreless wall swtch gateway control mplementng scheduled and demand response events Document Conventons Ths document ncludes the followng conventons to draw attenton to mportant nformaton. Notes are helpful hnts or nformaton that supplement the man content. Echoflex's user documentaton s desgned for prnt or electronc use. Benefts to usng the electronc format nclude usng the table of contents to jump to a desred page by clckng on the headng or usng word search to fnd a specfc topc. Cross references hghlghted n ths document are lnks to the referenced secton of the gude. Confguraton parameters are emphaszed throughout the gudes content n talcs. Addtonally, button and swtch actons (ON/OFF)and relay events (lghts ON/OFF) are emphaszed throughout ths gude n ALL CAPS. Ths gude s avalable for free download from Echoflex Solutons webste: 1 Fxture Controller Programmng Gude

6 Overvew The ELED1 s a complete stand-alone lghtng controller requrng only remote lnked devces to provde nput on lght level, occupancy state and swtch operaton. The controller wll perform common lghtng control applcatons: Vacancy Sensor Mode - partal OFF or fully OFF Occupancy Sensor Mode - partal ON or fully ON and photo nhbt Wall Swtch - ON/OFF, manual adjustment of dm level and tmed swtch Daylght Harvestng - open loop or closed loop Demand Response - sets a temporary hard lmt to the maxmum dmmng output Schedulng va nterfaces or gateways Rado Communcatons The ELED1 s a wreless devce capable of transmttng and recevng telegrams. The controller supports: Telegram repeatng, sngle and dual hop Controller status broadcast Auto-Detect Dmmng The controller automatcally detects when the purple and gray dmmng wres are connected to a drver or ballast that sources dmmng current. When the dmmng nterface wres are unconnected, dmmng wll be dsabled and fade tmers set to 0 seconds so the relay s acton s mmedate upon a lnked swtch or sensor's ON/OFF event. Overvew 2

7 Dmmng Output The controller's dmmng output s a 0-10V output provdng lnear, proportonal dmmng control of a dmmng drver or ballast. The maxmum and mnmum levels of the output can be confgured usng Garbald software. Maxmum dmmng level - the hgh level trm of the dmmng output, set to 100% by default Mnmum dmmng level - the low level trm of the dmmng output, set to 0% by default The dmmng output can also be dsabled through Garbald software allowng for mmedate relay control of the lghts. Near-Cross Relay Technology The ELED1 montors the AC voltage waveform so t operates the relay, ether open or closed, when the waveform s close to zero. Ths prevents carbon buld-up on the relay contacts ensurng the controller wll contnue to provde trouble-free operaton for years. 3 Fxture Controller Programmng Gude

8 Swtch Operaton The parameters dscussed n ths secton are confgurable. Refer to Confgurng the Controller for more detals on accessng these parameters. The controller operates wth sngle and dual-paddle wall, wave and hand-held Echoflex swtches. A quck press ON acton actvates the relay closed (lghts on) and the dmmng output wll ramp to the last manually set dm level. A quck double-press ON wll fade up to maxmum dmmng level and accelerate the fade perod to ½ second. A quck press OFF acton wll fade the lghts down to the mnmum dmmng level and then open the relay (lghts off). A quck doublepress OFF wll accelerate the fade perod to ½ second. Echoflex swtches can also be used as dmmer swtches when the dmmng output of the controller s enabled. Press and hold the ON or OFF sde to modulate the dmmng output up to the maxmum dmmng level or down to the mnmum dmmng level. Tmed Swtches The controller can be confgured so any lnked sngle or dual paddle swtch becomes a tmed swtch. A swtch ON closes the relay (lghts on) and the tmed swtch tmer s set. One mnute before the tmer expres, there wll be a flck-warn (lghts quck OFF then ON) to warn occupants of the pendng OFF event. Once the tmer expres, the relay opens (lghts off). The tmer can be reset at any tme by pressng a lnked swtch ON. A swtch OFF event clears the tmer and turns the lghts OFF. The tme perod s confgurable usng Garbald software. Overvew - Swtches 4

9 Occupancy Based Lghtng Applcatons The parameters dscussed n ths secton are confgurable. Refer to Confgurng the Controller for more detals on accessng these parameters. The controller wll turn the lghts OFF or fade down to a preset level when there s no moton detected n the room ndcated by all lnked occupancy sensors. There s a confgurable tme perod that must expre frst before the controller completes the vacancy acton. The occupancy auto-off tmer s set to 15 mnutes by default but can be changed usng Smple Tap Instructons or Garbald software. Grace Tmer The controller ncludes a grace tmer that starts countng down once the vacancy acton has been actvated. The grace tmer s a short perod of tme allowng an occupant to return the lghts to the prevous occuped state; ether through moton detecton or audo nput n the case of dual-tech sensors. Photo Inhbt Ths feature requres a lnked photo sensor n addton to the occupancy sensor and partal-on enabled (see Occupancy Sensors and Partal-ON). When photo-nhbt s enabled, the partal-on feature wll be gnored when the natural lght level measured by the lght sensor s above the daylghtng relay control set pont. The photo nhbt feature wll not turn lghts OFF f the lght s already ON. Photo Inhbt Operaton: Lght level s < daylghtng relay set pont The lghts turn ON automatcally when you enter the room. Lght level s > daylghtng relay set pont The lghts do not turn ON automatcally when you enter the room. Lghts are ON and the lght level ncreases past the daylghtng relay set pont the lghts stay ON. Lghts are OFF and the lght level decreases past the daylghtng relay set pont the lghts wll turn ON and ramp to the dm level defned n the partal-on settng upon the next moton detected by the occupancy sensor. 5 Fxture Controller Programmng Gude

10 Dual Technology Occupancy Sensors Echoflex dual technology sensors have bult-n occupancy tmers that manage the transton from occuped to the vacant state. The controller should be confgured to allow the dual-tech sensor control of the vacancy acton by settng the controllers occupancy auto-off tmer to 0 seconds. To change ths tmer, refer to the Smple Tap Instructons. Occupancy Sensors and Partal-ON When only occupancy sensors are lnked to the controller, the sensor wll automate the lghts both ON and OFF. The dmmng output for the ON acton wll adjust to the partal-on dmmng level (default 100%). Ths value s confgurable to accommodate partal-on applcatons usng Garbald software. Occupancy Sensors and Partal-OFF If the applcaton requres the lghts to reman ON durng vacant perods but at a dmmed level (partal-off), the partal-off dmmng level confguraton property accessble usng Garbald software can enable ths feature. Occupancy Sensors wth Swtches When swtches and sensors are lnked, the controller wll assume manual-on, auto-off operaton referred to as Vacancy Sensor Mode. The controller can be confgured to turn the lghts ON mmedately wth moton (partal-on) usng Smple Tap Instructons or Garbald software. When the swtch s used by pressng on or off, ths acton wll reset the occupancy auto-off tmer and set the sensor state to occuped. Overvew - Occupancy Applcatons 6

11 Daylght Harvestng Applcaton The parameters dscussed n ths secton are confgurable. Refer to Confgurng the Controller for more detals on accessng these parameters. The controller wll modulate the lght ntensty from a dmmng fxture based on the ambent lght level n the room when the dmmng output n enabled. The controller can also be confgured to turn the lght off wth suffcent natural lght. A lnked photo sensor montors the ambent lght level and transmts ths value to the controller. The controller wll only allow 1 lnked photo sensor. The daylght control applcaton has several confguraton varables: Daylghtng open/closed loop set ponts - the daylght harvestng applcaton serves two separate functons, closed loop control or open loop control. Daylghtng relay set pont - the ambent lght level that wll automate the relay The daylght harvestng applcaton does not affect the operaton of the wall swtch or occupancy sensor when the lght s on. If the lght s ON, ether the swtch or occupancy sensor can overrde the lght OFF or dm down below the daylghtng control value. See the secton ttled Photo Inhbt for addtonal functonalty. Daylghtng Relay Control When daylghtng relay control s enabled, the daylghtng sequence wll open the relay when the lght value montored by the sensor s greater than the daylghtng relay control-off set pont for a perod exceedng the daylghtng relay-off pause. The relay wll not close when the ambent lght reduces. A lnked occupancy sensor or wall swtch must reactvate the lghts after the daylghtng relay control has shut the lghts off. If the controller has only a photo sensor lnked and daylghtng relay control enabled, the relay wll close once the ambent lght falls below the daylghtng relay control-on set pont for a perod exceedng the daylghtng relay-on pause. 7 Fxture Controller Programmng Gude

12 Daylghtng Control Overrde The open or closed loop daylghtng features can be temporarly overrdden by enablng the daylghtng overrde confguraton parameter. The overrde has a tmer that wll release the overrde once expred and daylghtng control wll resume. When the overrde s enabled, a swtch can operate the relay ON and manually set the dmmng level. Both the daylghtng overrde tmer and overrde enable parameters are accessble wth Garbald software. Closed Loop Daylghtng Control Closed loop daylghtng becomes actve when a photo sensor wth a maxmum detectable range of lght less than 2500 lux s lnked to the controller. Closed loop daylghtng applcatons are defned when the sensor ndrectly montors the controlled lght output from the fxtures plus some of the natural lghts contrbuton. When the lghts are on, closed loop daylghtng wll try to mantan a gven set pont level wthn the space. Ths level s specfed n the closed loop daylghtng set pont confguraton parameter. The controller only adjusts the dmmng output upon receved photo sensor telegrams and only when the relay s closed. If the relay s open, closed loop daylghtng s gnored. The closed loop daylghtng set pont s adjustable usng Smple Tap Instructons or Garbald software. Whle mantanng the set pont, the dmmng output level wll only change a small amount of the output's full range wth every receved photo sensor telegram. The closed loop maxmum output change s set to 10% by default. Ensure the wreless photo sensor beng used has an update rate that s approprate to ndoor closed loop lghtng applcatons. The perod between consecutve telegrams should not exceed 200 seconds. The output dmmng level wll not change when the photo sensor level s wthn (+ or -) the closed loop dead-band value of the closed loop daylghtng set pont. Both the amount change per telegram and dead-band are confgurable parameters accessble usng Garbald software. Overvew - Daylghtng 8

13 Open Loop Control Open loop daylghtng becomes actve when a photo sensor wth a maxmum detectable range of lght greater than 2500 lux s lnked to the controller. Open loop daylghtng applcatons are defned when the sensor s montorng the natural lght contrbuton and s not affected by the controlled fxture's lght output. When the lght level montored by the photo sensor s below the open-loop maxmum output set pont, the dmmng output wll be at the maxmum output level. When the lght level s above the open-loop mnmum output set pont, the dmmng output wll be at the mnmum output level. In the dagram below, the bold blue lne ndcates the dmmng output. The output wll begn lowerng as the natural lght level ncreases (green dashed lne). When the montored lght level s between the set ponts t wll modulate the dmmng output proportonally. Photo Sensor Value Dmmng Output Value Max.Output Level Dmmng Output Range Mn.Output Level 0% Max. Mn. 100% SP% Photo Sensor SP% Range The rate the dmmng output wll change s defned by the confguraton parameter open loop dmmng rate whch defnes the tme for the dmmng to go from 0% to 100% or vce versa. The open loop maxmum output set pont and mnmum output set pont are adjustable usng Smple Tap Instructons or Garbald software. 9 Fxture Controller Programmng Gude

14 Controller Button Interface ELED1-AU LED Fxture Controller Clear Button Power LED Learn LED Learn Button LEARN button The LEARN button s used to lnk swtches or sensors to the controller. 1. Press the button marked LEARN for a half second. In lnk mode the green LEARN led wll stay ON and the red POWER led wll toggle every two seconds. 2. When lnkng a wall swtch, press the swtch paddle ON three tmes. If lnkng a sensor, press the sensor's TEACH or LINK button, refer to the sensor's documentaton. The red POWER led wll reman lt for four seconds whle t lnks the new devce. It wll resume togglng allowng you to lnk another devce up to a total of twenty devces. Lnkng a swtch or sensor that s already lnked to a controller, wll remove or unlnk t from the controller. 3. To ext lnk mode, press the LEARN button on the controller agan for a half second. Lnk mode wll tme out after no actvty n thrty seconds. CLEAR button Usng the CLEAR button can reload the controller to the factory precommssoned settngs wth lnked devces OR t can load the factory default parameters and remove all lnked devces. To return the controller to the factory pre-commssoned state, press the CLEAR button untl the red POWER and green LEARN LEDs start blnkng, approxmately 5 seconds. Release the button and the red POWER led wll begn blnkng ndcatng the factory commssoned pre-lnked devces. To completely CLEAR the controller back to factory default Controller Interface 10

15 settngs removng any lnked devces, press the CLEAR button untl the red POWER and green LEARN LEDs come on sold, about 15 seconds. The POWER led wll stay ON sold ndcatng the factory default state. Power LED and Learn LED The Power LED s red and when blnkng, provdes nformaton on the number and type of lnked devces to the controller. The Learn LED s green and ndcates when the controller s n Learn mode. Refer to LED Blnk Codes and Operaton n Appendx A. Dsablng the User Interface LEDs The LEDs can be dsabled by adjustng a confguraton parameter usng Garbald software. The varable s a tmer n seconds. If dsabled, the LEDs wll llumnate for the confgured tme when ether controller button s pressed, when n lnk mode or f the remote management Acton command s used to toggle the relay. 11 Fxture Controller Programmng Gude

16 Confgurng the Controller There are two methods of confgurng parameters n the controller. 1. Smple Tap Smple Tap s a quck method of changng a parameter's settng, one at a tme. 2. Garbald Commssonng Software (not covered n ths gude) Contact Echoflex Solutons for more nformaton on Garbald software. Confgurng the Controller 12

17 Smple Tap Instructons Smple Tap uses the swtches and sensors that are lnked to the controller to set the assocated confguraton parameters. You must be able to access the sensor's teach button and/or the swtches to perform Smple Tap. If the sensor s lnked to multple controllers and you do not want to make changes to all, turn the controllers relay off (lghts off) to gnore the Smple Tap changes. Smple Tap allows you to: Enable/Dsable the Repeater Functon Enable/Dsable the Status Telegram Enable/Dsable the Automatc Partal-ON feature Set the Occupancy Sensor Auto-OFF tmer Enable/Dsable Daylghtng Relay Control Set the Closed Loop Daylghtng Set Pont Set the Open Loop Daylghtng Set Pont 13 Fxture Controller Programmng Gude

18 Enable/Dsable the Repeater Functon Enablng the repeater functon wll repeat receved telegrams when: the telegram has not been prevously repeated. n the case of dual hop repeatng, have been repeated once prevously Ths sequence requres access to the controller. The repeater functon can be enabled/dsabled by accessng the controller's buttons and supports sngle and dual hop repeatng. 1. Press the CLEAR button and hold 2. Quckly tap the LEARN button; once to dsable repeatng twce to enable sngle hop repeatng three tmes to enable dual hop repeatng 3. Release the CLEAR button. The green LEARN and red POWER LEDs wll blnk the correspondng value of the LEARN button presses. Enable/Dsable the Status Telegram The controller can broadcast a telegram per EEP: A Status Feedback Telegram. The telegram wll broadcast every 100 seconds. The status telegram can be enabled/dsabled by accessng the controller buttons. 1. Press the LEARN button and hold, quckly tap the CLEAR button once to dsable, twce to enable. 2. Release the LEARN button. The green LEARN and red POWER LEDs wll blnk the correspondng value of the CLEAR button presses. Enable/Dsable the Automatc Partal-ON feature 1. Wth the lght on, tap the occupancy sensor's teach button followed by three quck consecutve clcks of a lnked wall swtch ON. 2. To enable automatc partal-on, clck once more ON; to dsable clck OFF. The lght wll blnk once to confrm the change. Confgurng the Controller 14

19 Set the Occupancy Sensor Auto-OFF tmer 1. Wth the lght on, tap the occupancy sensor's TEACH button three tmes to edt the tmer perod. The relay wll blnk the lght to acknowledge. 2. Tap the TEACH button agan to match the desred tmer perod. There are sx possble settngs, see the table below. The relay wll further blnk the lght a set number tmes based on the settng chosen and return to normal operaton. Smple Tap Occupancy Tmer Values Taps Occ. Sensor Tmer Lght Blnks 3 taps* 0 sec. 1 blnk 4 taps 5 mn. 2 blnks 5 taps 10 mn. 3 blnks 6 taps 15 mn. 4 blnks 7 taps 20 mn. 5 blnks 8 taps 25 mn. 6 blnks * uses the sensor's tmer When settng the tmer to 15 mnutes, the lght wll blnk 5 tmes total - once on the thrd press then 4 more after the last button press 15 Fxture Controller Programmng Gude

20 Enable/Dsable Daylghtng Relay Control You can enable or dsable (default) daylghtng relay control. If the dmmng output s dsabled and a photo sensor s lnked to the controller, daylghtng relay control wll automatcally be enabled. When enabled, the daylghtng sequence wll open the relay when the lght value montored by the sensor s greater than the daylghtng relay control-off set pont for a perod exceedng the daylghtng relay off pause. If the controller has only a photo sensor lnked and daylghtng relay control enabled, the relay wll close once the ambent lght falls below the daylghtng relay control-on set pont for a perod exceedng the daylghtng relay on pause. A lght sensor and wall swtch must be lnked to the controller before proceedng. 1. Press the photo sensor's TEACH button once followed by clckng the swtch ON three tmes wthn 5 seconds. 2. Ether clck the swtch once more ON to enable Daylghtng Relay Control or clck the swtch once OFF to dsable Daylghtng Relay Control. The relay wll cycle once to confrm the change and return to normal operaton. Set the Closed Loop Daylghtng Set Pont A lght sensor wth montorng range less than 2500 lux must be lnked to the controller plus a swtch. Ths process s best performed when there s lttle or no natural lght; ether close the blnds or complete ths step at nght 1. Wth the lght on and usng a hand-held photometer to measure the lght on the task plane, adjust the lght level from the fxture usng the swtch untl t matches the target lght level. 2. Tap the lght sensor s TEACH button 3 tmes to set the daylght harvestng parameters to closed loop functon. The lght wll blnk once to acknowledge the change. 3. Move away from the sensor so your shadow does not affect the lght level the sensor records. The lght wll blnk once agan after a pause when recevng the next telegram from the sensor. The pause may take up to 150 seconds. After blnkng, the controller wll return to normal operaton 16

21 Set the Open Loop Daylghtng Set Pont A lght sensor wth montorng range greater than 2500 lux must be lnked to the controller. Ths process adjusts the open loop maxmum output dmmng set pont and the open loop mnmum output dmmng set pont. Both set ponts are also confgurable usng Garbald software. The set ponts are n measured n percentage of the photo sensor's full scale range. 1. Wth the lght on, tap the lght sensor's TEACH button three tmes. The lght wll blnk once. 2. You can tap the TEACH button agan referrng to the tables below to set the open loop set ponts. Tappng the TEACH button ncrements the row selected n the table. 3. The lght wll blnkng accordng to the level set to confrm the change after fve seconds and return to normal operaton. Daylghtng Set Ponts - Open Loop Dmmng Sensor Range of > 2500 lux to < lux Taps Max. Output SP Mn. Output SP Lght Blnks 0 taps 20% 100% 1 blnks 1 taps 30% 100% 2 blnks 2 taps 40% 100% 3 blnks 3 taps 50% 100% 4 blnks 4 taps 60% 100% 5 blnks Daylghtng Set Ponts - Open Loop Dmmng Sensor Range of > 11000lux Taps Max. Output SP Mn. Output SP Lght Blnks 0 taps 5% 30% 1 blnks 1 taps 10% 35% 2 blnks 2 taps 15% 40% 3 blnks 3 taps 20% 50% 4 blnks 4 taps 25% 55% 5 blnks Ths concludes the confguraton drectons for the controller. 17 Fxture Controller Programmng Gude

22 Appendx A LED Blnk Codes and Operaton The tables below descrbe the LED actvty & assocated mode of the controller. If the controller was factory pre-commssoned, upon power up t wll mmedately begn blnkng the red POWER LED based on the type and count of lnked devces. The type s ndcated by long blnks followed by short blnks countng the number of devces lnked. Ths pattern wll repeat after a short pause. The table below descrbes the number of LED blnks for each devce type. Factory Default swtch(es) occupancy sensor(s) photo sensor(s) central command demand response POWER LED Blnk Codes ON Sold 1 long blnk followed by short blnks countng swtches 2 long blnks followed by short blnks countng sensors 3 long blnks followed by short blnks countng sensors 4 long blnks followed by short blnks countng devces 5 long blnks followed by short blnks countng devces Operatng Mode and LED Actvty Mode Green LEARN led Red POWER led Relay/Lght LINK mode ON Toggle Toggle Storng ID ON ON 4 sec. ON 4 seconds Clearng ID ON OFF 4 sec. OFF 4 seconds Factory Default OFF ON sold ON The LEDs can be dsabled by adjustng a confguraton parameter usng Garbald software. If dsabled, the LEDs wll llumnate for a bref perod of tme when ether controller button s pressed, when n lnk mode or f the remote management Acton command s used to toggle the relay. 18

23 Agency Lstngs and Regulatory Statements UL Lsted Component Certfed UL Standard Certfed CAN/CSA Std E60730 UL 2043 Plenum rated FCC Part : Contans FCC ID: SZV-STM300U IC RSS-210FCC Part : Contans FCC ID: SZV-STM300U The enclosed devce comples wth Part 15 of the FCC Rules. Operaton s subject to the followng two condtons: (I.) ths devce may not cause harmful nterference and (.) ths devce must accept any nterference receved, ncludng nterference that may cause undesred operaton. Safety Standards Load Ratngs Electronc Ballast or LED Drver 120 to 277VAC 19 Fxture Controller Programmng Gude

24 Status Feedback Telegram EEP:A Lghtng Controller DB_3 Illumnaton Sensor Range Mn..Max, lnear DB_2 llumnaton Closed Loop Set Pont, % of 255 DB_1: Dmmng Output Level, % of 255 DB_0.BIT_7: Repeater 0b0 dsabled, 0b1 enabled DB_0.BIT_6: not used DB_0.BIT_5: Daylght Harvestng 0b0 dsabled 0b1 enabled DB_0.BIT_4: Dmmng 0b0 swtchng 0b1 dmmng DB_0.BIT_3: Learn button 0b0 Teach-n 0b1 Data DB_0.BIT_2: not used DB_0.BIT_1: Occupancy 0b0 unoccuped 0b1 occuped DB_0.BIT_0: Power Relay 0b0 off 0b1 on Status Telegram 20

25 Echoflex Solutons Queens Way, Unt #1, Squamsh, BC, V8B 0K8, Canada n echoflexsolutons.com n 8DC-5745 Rev 1.2 n 12/18