H3CR. Multifunctional Timer Twin Timer Star-delta Timer Power OFF-delay Timer H3CR-A H3CR-AS H3CR-AP H3CR-A8 H3CR-A8S H3CR-A8E H3CR-G H3CR-G8EL

Transcription

1 Solid-sae Timer H3CR Please read and undersand his caalog before purchasing he producs. Please consul your OMRON represenaive if you have any quesions or commens. Refer o Warrany and Applicaion Consideraions (CD), and Safey Precauions (pages 1-23, 1-44, Common o H3CR on CD). DIN 48 x 48-mm Mulifuncional Timer Series Conforms o EN and IEC kv/2 for Low Volage, and EMC Direcives. Approved by UL and CSA. Lloyds/NK approvals. Six-language insrucion manual provided. Timers Broad Line-up of H3CR Series H3CR H3CR-A H3CR-F H3CR-G H3CR-H Mulifuncional Timer Twin Timer Sar-dela Timer OFF-delay Timer H3CR-A H3CR-AS H3CR-AP H3CR-A8 H3CR-A8S H3CR-A8E 11-pin model 8-pin model 8-pin wih insananeous conac oupu model H3CR-F H3CR-FN H3CR-F-300 H3CR-FN-300 H3CR-F8 H3CR-F8N H3CR-F8-300 H3CR-F8N pin model 8-pin model H3CR-G8L H3CR-G8EL 8-pin model H3CR-HRL H3CR-H8L H3CR-H8RL 11-pin model 8-pin model Noe: H3CR-AS, H3CR-A8S: Transisor oupu models Conens Solid-sae Timer H3CR-A... 3 H3CR-F H3CR-G H3CR-H Common o all H3CR Operaion Accessories Safey Precauions Solid-sae Timer H3CR 1

2 2 Solid-sae Timer H3CR

3 Solid-sae Muli-funcional Timer H3CR-A DIN 48 x 48-mm Sae-of-he-ar Mulifuncional Timer A wider power supply range reduces he number of imer models kep in sock. A wide range of applicaions hrough six or four operaing modes. Reduced power consumpion. (Excep for H3CR-A8E) Enables easy sequence checks hrough insananeous oupus for a zero se value a any ime range. Lengh, when panel-mouned wih a Socke, of 80 mm or less. Time Seing Rings enable consisen seings and limi he seing range. Panel Covers enable various panel designs. PNP inpu models available. Rich variey of inpus: Sar, rese, and gae funcions (11-pin models and -AP models) Model Number Srucure Timers Model Number Legend Noe: This model number legend includes combinaions ha are no available. Before ordering, please check he Lis of Models on page 1-4 for @ Number of Pins None: 11-pin models 8: 8-pin models 2. Inpu Type for 11-pin Models None: No-volage inpu (NPN ype) P: Volage inpu (PNP ype) 3. Oupu None: Relay oupu (DPDT) S: Transisor oupu (NPN/PNP universal use) E: Relay oupu (SPDT) wih insananeous relay oupu (SPDT) 4. Suffix 300: Dual mode models (signal ON/OFF-delay and one-sho) 301: Double ime scale (range) models (0.1 s o 600 h) 5. Supply Volage AC/ DC: 100 o 240 VAC/100 o 125 VDC 24-48AC/12-48DC: 24 o 48 VAC/12 o 48 VDC 24-48AC/DC: 24 o 48 VAC/VDC (Only for H3CR-A8E) Solid-sae Muli-funcional Timer H3CR-A 3

4 Ordering Informaion Lis of Models Noe: 1. Specify boh he model number and supply volage when ordering. Example: H3CR-A AC/ DC 11-pin Models Conac 8-pin Models Supply volage 2. The operaing modes are as follows A: ON-delay D: Signal OFF-delay B: Flicker OFF sar E: Inerval B2: Flicker ON sar G: Signal ON/OFF-delay C: Signal ON/OFF-delay J: One-sho Transisor (Phoocoupler) Conac Transisor (Phoocoupler) Oupu Supply volage Inpu ype Time range Operaing mode (See noe 2) 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC No-volage inpu 0.05 s o 300 h Six muli-modes: A, B, B2, C, D, E Dual-modes: G, J Volage inpu Six muli-modes: A, B, B2, C, D, E Model (See noe 1.) H3CR-A H3CR-A-300 H3CR-AP No-volage inpu 0.1 s o 600 h H3CR-A s o 300 h H3CR-AS Oupu Supply volage Inpu ype Time range Operaing mode (See noe 2) Time-limi conac and insananeous conac 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC/VDC (50/60 Hz) No-inpu available 0.05 s o 300 h Four muli-modes: A, B2, E, J ( supply sar) Model (See noe 1.) H3CR-A8 0.1 s o 600 h H3CR-A s o 300 h H3CR-A8S H3CR-A8E 4 Solid-sae Muli-funcional Timer H3CR-A

5 Accessories (Order Separaely) Name/specificaions Models Flush Mouning Adaper Y92F-30 Y92F-73 Y92F-74 Mouning DIN-rail 50 cm (l) x 7.3 mm () PFP-50N 1 m (l) x 7.3 mm () PFP-100N 1 m (l) x 16 mm () PFP-100N2 End Plae PFP-M Spacer PFP-S Proecive Cover Y92A-48B DIN-rail Mouning/ 8-pin P2CF-08 Fron Connecing Socke 8-pin, finger safe ype P2CF-08-E 11-pin P2CF pin, finger safe ype P2CF-11-E Back Connecing Socke 8-pin P3G-08 8-pin, finger safe ype P3G-08 wih Y92A-48G (See noe 1) 11-pin P3GA pin, finger safe ype P3GA-11 wih Y92A-48G (See noe 1) Time Seing Ring Seing a specific ime Y92S-27 Limiing he seing range Y92S-28 Panel Cover (See noe 2) Ligh gray (5Y7/1) Y92P-48GL Black (N1.5) Y92P-48GB Medium gray (5Y5/1) Y92P-48GM Hold-down Clip (See noe 3) For PL08 and PL11 Sockes Y92H-7 For PF085A Socke Y92H-8 Timers Noe: 1. Y92A-48G is a finger safe erminal cover which is aached o he P3G-08 or P3GA-11 Socke. 2. The Time Seing Ring and Panel Cover are sold ogeher. 3. Hold-down Clips are sold in ses of wo. Specificaions General Iem H3CR-A/-AS H3CR-AP H3CR-A8/-A8S H3CR-A8E Operaing mode A: ON-delay B: Flicker OFF sar B2: Flicker ON sar C: Signal ON/OFF-delay D: Signal OFF-delay E: Inerval G: Signal ON/OFF-delay (Only for H3CR-A-300) J: One-sho (Only for H3CR-A-300) A: ON-delay (power supply sar) B2: Flicker ON sar (power supply sar) E: Inerval (power supply sar) J: One-sho (power supply sar) Pin ype 11-pin 8-pin Inpu ype No-volage inpu Volage inpu --- Time-limi oupu ype H3CR-A/-A8/-AP: Relay oupu (DPDT) Relay oupu (SPDT) H3CR-AS/-A8S: Transisor oupu (NPN/PNP universal)* Insananeous oupu --- Relay oupu (SPDT) ype Mouning mehod DIN-rail mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds Conforms o EN and IEC (VDE0110) 4kV/2. Oupu caegory according o EN for Timers wih Conac Oupus. Oupu caegory according o EN for Timers wih Transisor Oupus. *The inernal s are opically isolaed from he oupu. This enables universal applicaion as NPN or PNP ransisor. Solid-sae Muli-funcional Timer H3CR-A 5

6 Time Ranges Noe: When he ime seing knob is urned below 0 unil he poin where he ime seing knob sops, he oupu will operae insananeously a all ime range seings. Sandard (0.05-s o 300-h) Models Time uni s (sec) min (min) h (hrs) x10 h (10 h) Full scale seing o o o o 3 3 o o o o o 300 Double (0.1-s o 600-h) Models Time uni s (sec) min (min) h (hrs) x10 h (10 h) Full scale seing o o o o 6 6 o o o o o 600 Raings Raed supply volage (See noe 1) Operaing volage range rese Inpu consumpion 100 o 240 VAC (50/60 Hz)/100 o 125 VDC, 24 o 48 VAC (50/60 Hz)/12 o 48 VDC (24 o 48 VAC/VDC for H3CR- A8E) (See noe 2) 85% o 110% of raed supply volage (90% o 110% a 12 VDC) Minimum power-opening ime: 0.1 s No-volage Inpu ON impedance: 1 kω max. ON residual volage: 1 V max. OFF impedance: 100 kω min. Volage Inpu Max. permissible capaciance beween inpus lines (erminals 6 and 7): 1,200 pf Load connecable in parallel wih inpus (erminals 6 and 7). 100 o 240 VAC/100 o 125 VDC High (logic) level: 85 o 264 VAC/85 o VDC Low (logic) level: 0 o 10 VAC/0 o 10 VDC 24 o 48 VAC/12 o 48 VDC High (logic) level: 20.4 o 52.8 VAC/10.8 o 52.8 VDC Low (logic) level: 0 o 2.4 VAC/0 o 1.2 VDC H3CR-A/-A8 100 o 240 VAC/100 o 125 VDC (When a 240 VAC, 60 Hz) Relay ON: approx. 2.0 VA (1.6 W) Relay OFF: approx. 1.3 VA (1.1 W) 24 o 48 VAC/12 o 48 VDC (When a 24 VDC) Relay ON: approx. 0.8 W Relay OFF: approx. 0.2 W H3CR-AP (See noe 3) 100 o 240 VAC/100 o 125 VDC (When a 240 VAC, 60 Hz) Relay ON: approx. 2.5 VA (2.2 W) Relay OFF: approx. 1.8 VA (1.7 W) 24 o 48 VAC/12 o 48 VDC (When a 24 VDC) Relay ON: approx. 0.9 W Relay OFF: approx. 0.3 W H3CR-A8E 100 o 240 VAC/100 o 125 VDC (When a 240 VAC, 60 Hz) Relay ON/OFF: approx. 2 VA (0.9 W) 24 o 48 VAC/VDC (When a 24 VDC) Relay ON/OFF: approx. 0.9 W H3CR-AS/-A8S 24 o 48 VAC/12 o 48 VDC (When a 24 VDC) Oupu ON: 0.3 W Oupu OFF: 0.2 W Conrol oupus Time limi conacs: 5 A a 250 VAC/30 VDC, 0.15 A a 125 VDC, resisive load (cosφ = 1) Transisor oupu: Open collecor (NPN/PNP), 100 ma max. a 30 VDC max., residual volage: 2 V max. Insananeous conac: 5 A a 250 VAC/30 VDC, 0.15 A a 125 VDC, resisive load (cosφ = 1) Noe: 1. DC ripple rae: 20% max. if he power supply incorporaes a single-phase, full-wave recifier. 2. Each 24-o-48-VAC/12-o-48-VDC model causes an inrush curren of approximaely 0.85 A. Pay careful aenion when aemping o urn ON power o such a model wih non-conac oupu from a device such as a sensor. 3. The values are for when he erminals 2 and 7 and erminals 10 and 6 are shor-ed, and include he consumpion curren of he inpu. 6 Solid-sae Muli-funcional Timer H3CR-A

7 Characerisics Accuracy of operaing ±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s) ime Seing error ±5% FS ±50 ms (See noe 1) Rese ime Min. power-opening ime: 0.1 s max. Min. pulse widh: 0.05 s (H3CR-A/-AS) Rese volage 10% max. of raed supply volage Influence of volage ±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s) Influence of emperaure ±1% FS max. (±1%±10 ms max. in a range of 1.2 s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC (1,000 VAC for H3CR-A@S), 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed noncurren-carrying meal pars) 2,000 VAC (1,000 VAC for H3CR-A@S), 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) 2,000 VAC, 50/60 Hz for 1 min (beween inpu and conrol oupu erminals and operaion ) for H3CR-AP Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance 3 kv (beween power erminals) for 100 o 240 VAC/100 o 125 VDC, 1 kv for 24 o 48 VAC/12 o 48 VDC 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 240 VAC/100 o 125 VDC, 1.5 kv for 24 o 48 VAC/12 o 48 VDC and 24 o 48 VAC/VDC ±1.5 kv (beween power erminals) and ±600 V (beween no-volage inpu erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise) Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude each in 3 direcions for 2 hours each Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude each in 3 direcions for 10 minues each Desrucion: 1,000 m/s 2 3 imes each in 6 direcions Malfuncion: 100 m/s 2 3 imes each in 6 direcions Ambien emperaure Operaing: -10 C o 55 C (wih no icing) Sorage: -25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 20,000,000 operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) (See noe 2) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC : 6 kv conac discharge (level 3) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: IEC : 10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves:IEC : 10 V/m (900±5 MHz) (level 3) Immuniy Conduced Disurbance: IEC : 10 V (0.15 o 80 MHz) (level 3) Immuniy Burs: IEC : 2 kv power-line (level 3) 2 kv I/O signal-line (level 4) Immuniy Surge: IEC : 1 kv line o line (level 3) 2 kv line o ground (level 3) Case color Ligh gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 90 g Timers Noe: 1. The value is ±5% FS +100 ms o 0 ms max. when he C, D, or G mode signal of he H3CR-AP is OFF. 2. Refer o he Life-es Curve on page 1-8. Solid-sae Muli-funcional Timer H3CR-A 7

8 Life-es Curve 10,000 Swiching operaions (x 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma (100 ma for H3CR-A8E) a 5 VDC (failure level: P). Load curren (A) 8 Solid-sae Muli-funcional Timer H3CR-A

9 Connecions Block Diagrams H3CR-A/AS AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor Timers supply Oscillaion Couning Oupu Rese inpu, sar inpu, and gae inpu Inpu Indicaor -ON indicaor Oupu-ON indicaor H3CR-AP AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Oupu Sar Inpu Indicaor -ON indicaor Oupu-ON indicaor Solid-sae Muli-funcional Timer H3CR-A 9

10 H3CR-A8/A8S AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Oupu Indicaor -ON indicaor Oupu-ON indicaor H3CR-A8E AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Oupu Indicaor -ON indicaor Oupu-ON indicaor Insananeous oupu I/O Funcions Inpus (for -A/ Sar Sars ime-measuremen. -AS models) Rese Inerrups ime-measuremen and reses ime-measuremen value. No ime-measuremen is made and conrol oupu is OFF while he rese inpu is ON. Gae Prohibis ime-measuremen. Oupus Conrol oupu Oupus are urned ON according o designaed oupu mode when prese value is reached. Noe: H3CR-AP incorporaes sar inpu only. 10 Solid-sae Muli-funcional Timer H3CR-A

11 Terminal Arrangemen Noe: The delayed conac of convenional Timers was indicaed as The conac symbol of he H3CR-A is indicaed as 11-pin Models H3CR-A/-A-300/-A-301 (Conac Oupu) because is operaing mode is six muli-modes (four muli-modes for he H3CR-A8). 8-pin Models H3CR-A8/-A8-301 (Conac Oupu) Rese inpu Sar inpu Gae inpu Timers supply supply H3CR-A8S (Transisor Oupu) H3CR-AS (Transisor Oupu) Rese inpu Sar inpu Gae inpu supply Noe: Terminals 1, 3, 4, and 5 are empy. Terminals 2 and 7 are he same as for he H3CR-A8. supply H3CR-A8E (Conac Oupu) Noe: Terminals 1, 3, 4, and 8 are empy. Terminals 2, 5, 6, 7, and 10 are he same as for he H3CR-A. H3CR-AP (Conac Oupu) Sar inpu supply supply Noe: 1. Terminal 5 is empy. 2. Separae power supplies can be used for he Timer and inpus. Solid-sae Muli-funcional Timer H3CR-A 11

12 Inpu Connecions H3CR-A/-AS The inpus of he H3CR-A/-AS are no-volage (shor- or open) inpus. No-volage Inpus No-conac Inpu Conac Inpu No-conac Inpu (Connecion o NPN open collecor oupu sensor.) 12 o 24 VDC (sensor power supply) + DC power supply (Connecion o a volage oupu sensor.) 12 o 24 VDC (sensor power supply) + DC power supply Sensor Timer 5 Gae 6 Sar 7 Rese Timer 5 Gae 6 Sar 7 Rese Sensor Timer Gae Sar Rese 2 Inpu (0 V) 2 Inpu (0 V) 2 Inpu (0 V) Operaes wih ransisor ON Operaes wih relay ON Operaes wih ransisor ON No-volage Inpu Signal Levels No-conac inpu Conac inpu 1. Shor- level Transisor ON Residual volage: 1 V max. Impedance when ON: 1 kω max. 2. Open level Transisor OFF Impedance when OFF: 100 kω min. Use conacs which can adequaely swich 0.1 ma a 5 V 12 Solid-sae Muli-funcional Timer H3CR-A

13 H3CR-AP The sar inpu of he H3CR-AP is volage inpu. (Volage imposiion or open) Volage Inpus No-conac Inpu No-conac Inpu Conac Inpu (Connecion o PNP open (Connecion o NPN open collecor oupu sensor) collecor oupu sensor) 12 o 24 VDC (sensor power supply) Sensor + 10 supply (+) 6 Sar 7 2 DC power supply Timer Operaes wih PNP ransisor ON Inpu 0V supply ( ) Sensor 12 o 24 VDC (sensor power supply) + DC power supply 10 Operaes wih NPN ransisor ON Timer supply (+) Sar Inpu 0V supply ( ) AC power supply DC power supply Operaes wih relay ON 7 2 Timer 10 supply (+) 6 Sar Inpu 0V supply ( ) Timers Volage Inpu Signal Levels No-conac inpu Noe: The inpu is isolaed from he power supply. Thus, an NPN ransisor can be conneced. 1. Transisor ON Residual volage: 1 V max. The volage beween erminals 6 and 7 mus be 10.8 VDC min. Noe: Refer o he signal levels in he following able and be aware of he minimum applicable load of he relay. 2. Transisor OFF Leakage curren: 0.01 ma max. The volage beween erminals 6 and 7 mus be 1.2 VDC max. Conac inpu Use conacs ha can adequaely swich 0.1 ma a each operaing volage. The volage beween erminals 6 and 7 wih conacs ON or OFF mus saisfy he specified value. Conacs ON 100-o-240-VAC and 100-o-125-VDC models: 85 o 264 VAC or 85 o VDC 24-o-48-VAC and 12-o-48-VDC models: 20.4 o 52.8 VAC or 10.8 o 52.8 VDC Conacs OFF 100-o-240-VAC and 100-o-125-VDC models: 0 o 10 VAC or 0 o 10 VDC 24-o-48-VAC and 12-o-48-VDC models: 0 o 2.4 VAC or 0 o 1.2 VDC Solid-sae Muli-funcional Timer H3CR-A 13

14 Operaion Timing Char Noe: 1. The minimum power-opening ime ( R ) is 0.1 s. 2. The minimum inpu pulse widh (for sar, rese) is 0.05 s. 3. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. 4. supply sar in mode J is also possible for H3CR-A8/-A8E/-A8S/-A8-301 models. H3CR-A/-AS/-AP* *H3CR-AP model incorporaes sar inpu only. Operaing mode Timing char A: ON-delay Basic operaion Sar B: Flicker OFF sar B2: Flicker ON sar C: Signal ON/ OFFdelay Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar Sar (See noe) Oupu Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion Sar (See noe) Oupu Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion Sar (See noe) Oupu Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion Rese Oupu relay (NC) Sar (See noe) Oupu Oupu relay (NO) (Oupu indicaor) indicaor Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. 14 Solid-sae Muli-funcional Timer H3CR-A

15 Operaing mode D: Signal OFFdelay Sar Timing char Basic operaion Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor Sar (See noe) Oupu Noe: Sar inpu is valid and re-riggerable while he Timer is in operaion. Timers E: Inerval Sar Rese Oupu relay (NC) Basic operaion Sar (See noe) Oupu G: Signal ON/ OFFdelay Oupu relay (NO) (Oupu indicaor) indicaor Sar Basic operaion Noe: Sar inpu is valid and re-riggerable while he Timer is in operaion. Rese Oupu relay (NC) Sar (See noe) J: One-sho oupu Oupu relay (NO) (Oupu indicaor) indicaor Sar Oupu Noe: Sar inpu is valid and re-riggerable while he Timer is in operaion. Basic operaion Rese Oupu relay (NC) Oupu relay (NO) (Oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Sar (See noe) Oupu 1±0.6 s (Fixed) Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. Gae Signal Inpu ON OFF 1 2 Sar Gae Rese ON OFF ON OFF ON OFF Oupu ON relay OFF Noe: 1. This iming char indicaes he gae inpu in operaing mode A (ON-delay operaion). 2. The se ime is he sum of 1 and H3CR-AP model incorporaes sar inpu only. Solid-sae Muli-funcional Timer H3CR-A 15

16 H3CR-A8/-A8S Operaing mode Timing char A: ON-delay Basic operaion Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Oupu B 2 : Flicker ON sar Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Basic operaion Oupu E: Inerval Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor Basic operaion Oupu J: One-sho oupu Oupu relay (NC) Oupu relay (NO) (oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Basic operaion Oupu 1±0.6 s (Fixed) Noe: 1. The minimum power-opening ime ( R ) is 0.1 s. 2. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. 16 Solid-sae Muli-funcional Timer H3CR-A

17 H3CR-A8E Operaing mode A: ON-delay Timing char Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) Basic operaion Oupu Timers B 2 : Flicker ON sar E: Inerval indicaor Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) indicaor Basic operaion Oupu Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) indicaor Basic operaion Oupu J: One-sho oupu Oupu relay (NC) Oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) (Fixed) (Fixed) Basic operaion Oupu 1±0.6 s (Fixed) indicaor Noe: 1. The minimum power-opening ime ( R ) is 0.1 s. 2. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. Solid-sae Muli-funcional Timer H3CR-A 17

18 Nomenclaure Oupu indicaor (orange) (Li when oupu) indicaor (green) (Flashes when Timer operaes; li when Timer sops operaing) Operaing mode display window Operaing mode selecor Selec a mode from: A, B, B2, C, D, and E (H3CR-A, -AP, and -AS) A, B2, E and J (H3CR-A8, -A8S, and -A8E) G and J (H3CR-A-300) Scale range display windows Time range selecor (selec one from 1.2, 3, 12, and 30 a full scale; wih he H3CR-A@-301, selec from 2.4, 6, 24, or 60 a full scale. ) Time seing knob (se ime) Time uni display window Time uni selecor (selec one from sec, min, hrs, and 10h) 18 Solid-sae Muli-funcional Timer H3CR-A

19 Dimensions Noe: All unis are in millimeers unless oherwise indicaed. H3CR-A H3CR-AP H3CR-AS dia x 44.8 Timers 11 pins H3CR-A8 H3CR-A8S H3CR-A8E dia x pins Dimensions wih Se Ring dia. Dimensions wih Fron Connecing Socke P2CF-08-@/P2CF-11-@ Time Seing Ring Panel cover Dimensions wih Back Connecing Socke P3G-08/P3GA H3CR-A H3CR-AS 100.8* H3CR-AP 98.5 P2CF-11 P2CF-11-E 2.3* H3CR-A8@ 89.9* 87.6 P2CF-08 P2CF-08-E 2.3* H3CR-A H3CR-AS H3CR-AP + Adaper H3CR-A8@ + Adaper Y92F-30 P3GA-11 Y92F-30 P3G-08 (When (When Y92A-48G Y92A-48G mouned) mouned) *These dimensions vary wih he kind of DIN-rail (reference value). Solid-sae Muli-funcional Timer H3CR-A 19

20 Applicaion Examples (H3CR-A) A Mode: ON-delay ON-delay operaion (A mode) is a basic mode. 1. -ON Sar/-OFF Rese The -ON sar/-off rese operaion is a sandard operaing mehod. 3. Conrol of Inegraed Time wih Gae Signal Wih a gae signal, he -ON sar operaion and Signal sar operaion can be conrolled (he operaion can be inerruped). (2 and 10) : se ime Sar (2 and 6) (2 and 10) Rese (2 and 7) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Gae (2 and 5) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) indicaor Flashing Li Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Exernally shor-ed Flashing Li Gae signal (The operaion is inerruped wih he gae signal if he Timer deecs an abnormal signal.) Exernally shor-ed supply 2. Signal Sar/Signal Rese The Signal sar/signal rese operaion is useful for remoe conrol of he Timer. B/B2 Mode: Flicker supply (2 and 10) Sar (2 and 6) Rese (2 and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Sar signal (remoe conrol possible) Rese signal (remoe conrol possible) Li The flicker operaion in he B and B2 modes can be effecively applied o lamp or buzzer (ON and OFF) alarms or he monioring of an inermien operaion wih a display. 1. -ON Sar/-OFF Rese (in B Mode) (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Exernally shor-ed supply ( coninuously supplied) supply 20 Solid-sae Muli-funcional Timer H3CR-A

21 2. Signal Sar/Signal Rese (in B Mode) If here is an abnormal signal, flashing sars. When he abnormal condiion is resored, a rese signal sops he display flashing. 2. Signal-ON-OFF Sar/Insananeous Operaion/Time-limi Rese (2 and 10) Sar (2 and 6) Rese (2 and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Sar signal Rese signal (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Flashing Li Flashing Li Sar signal (The operaion sars wih he signal ON or OFF) Timers supply ( coninuously supplied) C Mode: Signal ON/OFF-delay The Signal ON-/OFF-delay operaion (C mode) is useful for he conrol of disribuion of producs on a producion line ino boxes by he specified number or ime. 1. -ON Sar/Insananeous Operaion/ Time-limi Rese A se of hese funcions is useful for he operaion of a machine for a specified period when power is ON. ( coninuously supplied) D Mode: Signal OFF-delay Signal OFF-delay operaion (D mode) can be effecively used o keep a load operaing for a cerain period. For example, his funcion enables he cooling fan for a lamp or heaer o operae for a cerain period afer he lamp or heaer is swiched OFF. 1. -ON Sar/Insananeous Operaion/ Time-limi Rese (2 and 10) Sar (2 and 6) supply (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Exernally shor-ed Sar signal (NC o NO) supply supply Solid-sae Muli-funcional Timer H3CR-A 21

22 2. Signal Sar/Insananeous Operaion/ Time-limi Rese (2 and 10) 2. Signal Sar/Insananeous Operaion/ Time-limi Rese This funcion is useful for he repeiive conrol such as he filling of liquid for a specified period afer each Signal sar inpu. Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Sar signal (NO o NC o NO) Sar signal E Mode: Inerval supply ( coninuously supplied) supply ( coninuously supplied) 1. -ON Sar/Insananeous Operaion/ Time-limi Rese This funcion is useful for he operaion of a machine for a specified period afer power is ON. (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Exernally shor-ed supply 22 Solid-sae Muli-funcional Timer H3CR-A

23 Safey Precauions (H3CR-A) Noe: The undermenioned is common for all H3CR-A models. Supplies Inpu/Oupu For he power supply of an inpu device of he use an isolaing ransformer wih he primary and secondary windings muually isolaed and he secondary winding no grounded. Correc G, S, R 5, 6, 7 2 H3CR-A Inpu erminal 10 2 supply Relaionship beween Inpu and Supply Circuis (excep for H3CR-A8E) The H3CR-A (excep for H3CR-A8E) uses ransformerless power supply. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shor-ing due o a sneak curren o he ransformerless power supply. If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no differ in phase, oherwise he erminals will be shor-ed o one anoher. Timers Incorrec Conac or ransisor for exernal inpu signal H3CR-A Shor- curren Inpu device Isolaion ransformer is required. Inpu erminal supply Incorrec G, S, R 5, 6, 7 2 H3CR-A Inpu erminal 10 2 supply Inpu erminal Correc Inpu erminal supply Inpu device Isolaion ransformer The H3CR-A@/-A@S/AP s power supply erminal 2 is a common erminal for inpu signals o he Timer. Do no disconnec he wires on erminal 2, oherwise he inernal ry of he Timer will be damaged. Inpu erminal 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A I is impossible o provide wo independen power swiches as shown below regardless of wheher or no he Timers are differen in phase. 2 Inpu erminal supply Make sure ha he volage is applied wihin he specified range, oherwise he inernal elemens of he Timer may be damaged. Inpu erminal Solid-sae Muli-funcional Timer H3CR-A 23

24 Relaionship beween Inpu and Supply Circuis An appropriae inpu is applied o he inpu signal erminals of he H3CR-A@/-A@S when one of he inpu erminals is shor-ed wih he common erminal (erminal 2) for he inpu signals. Never use erminal 10 as he common erminal for his purpose, oherwise he inernal of he Timer will be damaged. Incorrec 10 If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no be differen in phase or he erminals will be shor-ed o one anoher (refer o he figures below). Incorrec Conac or ransisor for exernal inpu signal H3CR-AP 2 supply AC or DC power supply 5, 6, 7 G, S, R Inpu erminal H3CR-A H3CR-AP Shor- curren Correc 2 AC or DC power supply 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A Correc Conac or ransisor for exernal inpu signal H3CR-AP supply Do no connec a relay or any oher load beween inpu erminals, oherwise he inernal of he Timer will be damaged due o he high-ension volage applied o he inpu erminals Shor- curren Ry 10 7 H3CR-AP AC or DC power supply Inpu conac 5, 6, 7 G, S, R Inpu erminal H3CR-A Relaionship beween Inpu and Supply Circuis (H3CR-AP) 2 Common o All H3CR-A Models 2 Wih he H3CR-AP, inpu wires mus be as shor as possible. If he floaing capaciy of wires exceeds 1,200 pf (approx. 10 m for cables wih 120 pf/m), he operaion will be affeced. Pay paricular aenion when using shielded cables. The H3CR-A@S ransisor oupu is isolaed from he inernal ry by a phoocoupler. Therefore, eiher NPN or PNP oupu is possible. H3CR-AP AC/DC power supply Inpu supply Since he inpu and he power supply are configured independenly, he inpu can be urned ON or OFF irrespecive of he ON/OFF sae of he power supply. I mus be noed ha a volage equivalen o he power supply volage is applied o he inpu. 24 Solid-sae Muli-funcional Timer H3CR-A

25 Solid-sae Twin Timer H3CR-F DIN 48 x 48-mm Twin Timers Wide power supply ranges of 100 o 240 VAC and 48 o 125 VDC respecively. ON- and OFF-imes can be se independenly and so combinaions of long ON- or OFF-ime and shor OFF- or ON-ime seings are possible. Foureen ime ranges from 0.05 s o 30 h or from 1.2 s o 300 h depending on he model o be used. Models wih a flicker ON sar or flicker OFF sar are available. Easy sequence checks hrough insananeous oupus for a zero se value a any ime range. Lengh, when panel-mouned wih a Socke, of 80 mm or less. 11-pin and 8-pin models are available. Model Number Srucure Timers Model Number Legend H3CR @ Classificaion F: Twin imers 2. Configuraion None: 11-pin socke 8: 8-pin socke 3. Twin Timer Mode None: Flicker OFF sar N: Flicker ON sar 4. Time Range None: 0.05 s o 30 h models 300: 1.2 s o 300 h models 5. Supply Volage AC: 100 o 240 VAC 24AC/DC: 24 VAC/VDC 12DC: 12 VDC DC: 48 o 125 VDC Ordering Informaion Lis of Models Operaing modes Flicker OFF sar Flicker ON sar Supply 0.05 s o 30 h models 1.2 s o 300 h models volage 11-pin models 8-pin models 11-pin models 8-pin models 100 o 240 VAC H3CR-F AC H3CR-F AC H3CR-F AC H3CR-F AC 24 VAC/DC H3CR-F 24AC/DC H3CR-F8 24AC/DC H3CR-F AC/DC H3CR-F AC/DC 12 VDC H3CR-F 12DC H3CR-F8 12DC H3CR-F DC H3CR-F DC 48 o 125 VDC H3CR-F DC H3CR-F DC H3CR-F DC H3CR-F DC 100 o 240 VAC H3CR-FN AC H3CR-F8N AC H3CR-FN AC H3CR-F8N AC 24 VAC/DC H3CR-FN 24AC/DC H3CR-F8N 24AC/DC H3CR-FN AC/DC H3CR-F8N AC/DC 12 VDC H3CR-FN 12DC H3CR-F8N 12DC H3CR-FN DC H3CR-F8N DC 48 o 125 VDC H3CR-FN DC H3CR-F8N DC H3CR-FN DC H3CR-F8N DC Solid-sae Twin Timer H3CR-F 25

26 Accessories (Order Separaely) Name/specificaions Noe: 1. Y92A-48G is a finger safe erminal cover which is aached o he P3G-08 or P3GA-11 Socke. 2. Hold-down Clips are sold in ses of wo. Models Flush Mouning Adaper Y92F-30 Y92F-73 Y92F-74 Mouning DIN-rail 50 cm (l) x 7.3 mm () PFP-50N 1 m (l) x 7.3 mm () PFP-100N 1 m (l) x 16 mm () PFP-100N2 End Plae PFP-M Spacer PFP-S Proecive Cover Y92A-48B DIN-rail Mouning/ 8-pin P2CF-08 Fron Connecing Socke 8-pin, finger safe ype P2CF-08-E 11-pin P2CF pin, finger safe ype P2CF-11-E Back Connecing Socke 8-pin P3G-08 8-pin, finger safe ype P3G-08 wih Y92A-48G (See noe 1) 11-pin P3GA pin, finger safe ype P3GA-11 wih Y92A-48G (See noe 1) Hold-down Clip (See noe 2) For PL08 and PL11 Sockes Y92H-7 For PF085A Socke Y92H-8 Specificaions General Iem H3CR-F H3CR-F8 H3CR-FN H3CR-F8N Operaing mode Flicker OFF sar Flicker ON sar Pin ype 11-pin 8-pin 11-pin 8-pin Operaing/Rese mehod Time-limi operaion/time-limi rese or self-rese Oupu ype Relay oupu (DPDT) Mouning mehod DIN-rail mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds Conforms o EN and IEC (VDE0110) 4kV/2. Oupu caegory according o EN Time Ranges 0.05 s o 30 h Models Time uni s (sec) x10 s (10 s) min (min) h (hrs) Seing o o o o 3 3 o o o o o o o o 30 Noe: Insananeous oupu is available a any ime range. To obain insananeous oupu, se o below s o 300 h Models Time uni x10 s (10 s) x10 min (10 min) h (hrs) x10 h (10 h) Seing o o o o o 30 3 o o 3 3 o o o o o o o o o 300 Noe: Insananeous oupu is available a any ime range. To obain insananeous oupu, se o below Solid-sae Twin Timer H3CR-F

27 Raings Raed supply volage (See noe) Operaing volage range rese Noe: A power supply wih a ripple of 20% max. (single-phase power supply wih full-wave recificaion) can be used wih each DC Model. Characerisics 100 o 240 VAC (50/60 Hz),12 VDC, 24 VAC/DC (50/60 Hz), 48 o 125 VDC 85% o 110% of raed supply volage; 90% o 110% wih 12-VDC models Minimum power-opening ime: 0.1 s consumpion 100 o 240 VAC: approx. 10 VA (2.1 W) a 240 VAC 24 VAC/VDC: approx. 2 VA (1.7 W) a 24 VAC approx. 1 W a 24 VDC 48 o 125 VDC: approx. 1.5 W a 125 VDC 12 VDC: approx. 1 W a 12 VDC Conrol oupus Conac oupu: 5 A a 250 VAC/30 VDC, resisive load (cosφ = 1) Accuracy of operaing ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 1.2 and 3 s) ime Seing error ±5% FS ±50 ms max. Rese ime 0.1 s max. Rese volage 10% max. of raed volage Influence of volage ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 1.2 and 3 s) Influence of emperaure ±1% FS max. (±1% FS ±10 ms max. in ranges of 1.2 and 3s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC, 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) 2,000 VAC, 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance 3 kv (beween power erminals) for 100 o 240 VAC, 48 o 125 VDC 1 kv for 12 VDC, 24 VAC/DC 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 240 VAC, 48 o 125 VDC 1.5 kv for 12 VDC, 24 VAC/DC ±1.5 kv (beween power erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise) ±400 V for 12 VDC Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude for 2 hrs each in hree direcions Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude for 10 min each in hree direcions Desrucion: 980 m/s 2 hree imes each in six direcions Malfuncion: 98 m/s 2 hree imes each in six direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 20 million operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) (See noe) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC : 6 kv conac discharge (level 3) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: IEC : 10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves: IEC : 10 V/m (900±5 MHz) (level 3) Immuniy Conduced Disurbance: IEC : 10 V (0.15 o 80 MHz) (level 3) Immuniy Burs: IEC : 2 kv power-line (level 3) 2 kv I/O signal-line (level 4) Immuniy Surge: IEC : 1 kv line o line (level 3) 2 kv line o ground (level 3) Case color Ligh Gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 100 g Timers Noe: Refer o he Life-es Curve on page Solid-sae Twin Timer H3CR-F 27

28 Life-es Curve 10,000 Swiching operaions (x 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC (failure level: P). Load curren (A) Connecions Block Diagrams ON indicaor OFF indicaor Zero seing deecion Indicaor ROM RAM Clock Oupu AC (DC) inpu supply One-chip microcompuer Time range/uni selecors I/O Funcions Inpus --- Oupus Conrol oupu Oupus are urned ON/OFF according o he ime se by he ON- and OFF-ime seing knob. Terminal Arrangemen H3CR-F8 H3CR-F8 NH3CR-F8-300 H3CR-F8N-300 H3CR-F H3CR-FN H3CR-F-300 H3CR-FN-300 (+)(~) supply supply Noe: Leave erminals 5, 6, and 7 open. Do no use hem as relay erminals. 28 Solid-sae Twin Timer H3CR-F

29 Operaion Timing Char ON : ON se ime OFF : OFF se ime Operaing mode Flicker OFF sar ON OFF Timing char OFF ON OFF ON OFF OFF 0.1 s min. Timers ON indicaor Li No li OFF indicaor Li No li Oupu NO ON OFF Flicker ON sar Oupu NC ON OFF ON OFF 0.1 s min. ON OFF ON OFF ON OFF ON indicaor OFF indicaor Li No li Li No li Oupu NO ON OFF Oupu NC ON OFF Noe: 1. The rese ime requires a minimum of 0.1 s. 2. When power is supplied in flicker ON sar mode, he OFF indicaor lighs momenarily. This, however, has no effec on he performance of he Timer. Nomenclaure OFF indicaor (green) Li when he oupu is OFF. ON indicaor (orange) Li when he oupu is ON. OFF-ime uni display window OFF-ime uni selecor (selec one from sec. 10 s, min., and hrs, or from 10 s, 10 min, hrs, and 10 h) Scale range display windows Time range selecor (selec one from 1.2, 3, 12, and 30 a full scale) For boh ON-ime and OFF-ime. ON-ime seing knob (wih orange poiner) For ON-ime seing OFF-ime seing knob (wih green poiner) For OFF-ime seing ON-ime uni display window ON-ime uni selecor (selec one from sec, 10 s, min, and hrs, or from 10 s, 10 min, hrs, and 10 h) Solid-sae Twin Timer H3CR-F 29

30 Dimensions Noe: All unis are in millimeers unless oherwise indicaed. H3CR-F H3CR-FN H3CR-F-300 H3CR-FN dia. 14 dia x 44.8 R pins H3CR-F8 H3CR-F8N H3CR-F8-300 H3CR-F8N dia x dia. Dimensions wih Fron Connecing Socke P2CF-08-@/P2CF-11-@ R1.3 Dimensions wih Back Connecing Socke P3G-08/P3GA-11 8 pins H3CR-F H3CR-FN 103.2* H3CR-F8 H3CR-F8N 92.3* H3CR-F H3CR-FN H3CR-F8 H3CR-F8N P2CF-11 P2CF-11-E 2.3* P2CF-08 P2CF-08-E *These dimensions vary wih he kind of DIN-rail (reference value). 2.3* Y92F-30 P3GA-11 (When Y92A-48G mouned) Y92F-30 P3G-08 (When Y92A-48G mouned) 30 Solid-sae Twin Timer H3CR-F

31 Solid-sae Sar-dela Timer H3CR-G DIN 48 x 48-mm Sar-dela Timer A wide sar-ime range (up o 120 seconds) and sar-dela ransfer ime range (up o 0.5 seconds). Timers Model Number Srucure Model Number Legend H3CR - G Classificaion G: Sar-dela imer 2. Configuraion 8: 8-pin socke 3. Oupus None: Sar-dela operaion conac E: Sar-dela operaion conac and insananeous conac 4. Dimensions L: Long-body model 5. Supply Volage AC: 100 o 120 VAC AC: 200 o 240 VAC Ordering Informaion Lis of Models Oupus Supply volage 8-pin models Time-limi conac 100 o 120 VAC H3CR-G8L AC 200 o 240 VAC H3CR-G8L AC Time-limi conac and insananeous conac 100 o 120 VAC H3CR-G8EL AC 200 o 240 VAC H3CR-G8EL AC Accessories (Order Separaely) Name/specificaions Flush Mouning Adaper Y92F-30 Y92F-70 Y92F-71 Mouning DIN-rail 50 cm (l) x 7.3 mm () PFP-50N 1 m (l) x 7.3 mm () PFP-100N 1 m (l) x 16 mm () PFP-100N2 End Plae PFP-M Spacer PFP-S Proecive Cover Y92A-48B Models Solid-sae Sar-dela Timer H3CR-G 31

32 Name/specificaions Models DIN-rail Mouning/ 8-pin P2CF-08 Fron Connecing Socke 8-pin, finger safe ype P2CF-08-E Back Connecing Socke 8-pin P3G-08 8-pin, finger safe ype P3G-08 wih Y92A-48G (See noe 1) Time Seing Ring Seing a specific ime Y92S-27 Limiing he seing range Y92S-28 Panel Cover (See noe 2) Ligh gray (5Y7/1) Y92P-48GL Black (N1.5) Y92P-48GB Medium gray (5Y5/1) Y92P-48GM Hold-down Clip (See noe 3) For PL08 and PL11 Sockes Y92H-1 For PF085A Socke Y92H-2 Noe: 1. Y92A-48G is a finger safe erminal cover which is aached o he P3G-08 Socke. 2. The Time Seing Ring and Panel Cover are sold ogeher. 3. Hold-down Clips are sold in ses of wo. Specificaions General Iem H3CR-G8L H3CR-G8EL Funcions Sar-dela imer Sar-dela imer wih insananeous oupu Pin ype 8-pin Operaing/Rese mehod Time-limi operaion/self-rese Oupu ype Time-limi: SPST-NO (sar operaion ) SPST-NO (dela operaion ) Time-limi: SPST-NO (sar operaion ) SPST-NO (dela operaion ) Insananeous: SPST-NO Mouning mehod DIN-rail mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds Conforms o EN and IEC (VDE0110) 4kV/2. Oupu caegory according o EN Time Ranges Time uni Sar operaion ime ranges Full scale seing o 6 s 12 1 o 12 s 60 5 o 60 s o 120 s Sar-dela ransfer ime Programmable a 0.05 s, 0.1 s, 0.25 s or 0.5 s 32 Solid-sae Sar-dela Timer H3CR-G

33 Raings Raed supply volage Operaing volage range rese 100 o 120 VAC (50/60 Hz), 200 o 240 VAC (50/60 Hz) 85% o 110% of raed supply volage Minimum power-opening ime: 0.5 s consumpion 100 o 120 VAC: approx. 6 VA (2.6 W) a 120 VAC 200 o 240 VAC: approx. 12 VA (3.0 W) a 240 VAC Conrol oupus Conac oupu: 5 A a 250 VAC/30 VDC, resisive load (cosφ = 1) Characerisics Accuracy of operaing ±0.2% FS max. ime Seing error ±5% FS ±50 ms max. Accuracy of Sar-dela ±25% FS + 5 ms max. ransfer ime Rese volage 10% max. of raed volage Influence of volage ±0.2% FS max. Influence of emperaure ±1% FS max. Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC, 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) 2,000 VAC, 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance 3 kv (beween power erminals) 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) ±1.5 kv (beween power erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise) Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude for 2 hrs each in hree direcions Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude for 10 min each in hree direcions Desrucion: 980 m/s 2 hree imes each in six direcions Malfuncion: 294 m/s 2 hree imes each in six direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 20 million operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) (See noe) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC : 6 kv conac discharge (level 3) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: IEC : 10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves: IEC : 10 V/m (900±5 MHz) (level 3) Immuniy Conduced Disurbance: IEC : 10 V (0.15 o 80 MHz) (level 3) Immuniy Burs: IEC : 2 kv power-line (level 3) 2 kv I/O signal-line (level 4) Immuniy Surge: IEC : 1 kv line o line (level 3) 2 kv line o ground (level 3) Case color Ligh Gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh H3CR-G8L: approx. 110 g; H3CR-G8EL: approx. 130 g Timers Noe: Refer o he Life-es Curve on page Solid-sae Sar-dela Timer H3CR-G 33

34 Life-es Curve 10,000 Swiching operaions (x 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC (failure level: P). Load curren (A) Connecions Block Diagrams H3CR-G8L Sar operaion ime range selecor Sar-dela ransfer ime selecor AC inpu supply Sar operaion ime oscillaion Sar operaion ime couning Sar-dela ransfer ime oscillaion Sar-dela ransfer ime couning Oupu Sar operaion Dela operaion Indicaor Sar operaion indicaor Dela operaion indicaor H3CR-G8EL Sar operaion ime range selecor Sar-dela ransfer ime selecor AC inpu supply Sar operaion ime oscillaion Sar operaion ime couning Sar-dela ransfer ime oscillaion Sar-dela ransfer ime couning Oupu Sar operaion Dela operaion Indicaor Sar operaion indicaor Dela operaion indicaor Insananeous oupu 34 Solid-sae Sar-dela Timer H3CR-G

35 I/O Funcions Inpus --- Oupus Conrol oupu If he ime reaches he value se wih he ime seing knob, he sar operaion oupu will be urned OFF and here will be dela operaion oupu afer he se sar-dela ransfer ime has elapsed. Terminal Arrangemen H3CR-G8L H3CR-G8EL Timers Dela operaion conac Sar operaion conac Insananeous conac Dela operaion conac Sar operaion conac Noe: Leave erminals 1, 3, and 4 open. Do no use hem as relay erminals. Noe: Leave erminal 4 open. Do no use hem as relay erminals. Operaion Timing Char 1: Sar operaion ime seing 2: Sar-dela ransfer ime Model H3CR-G8L/-G8EL Timing char 0.5 s min. (2 7) ON OFF Insananeous oupu (1 3) (-E models) ON OFF 1 Sar operaion oupu (8 5) ON OFF 2 Dela operaion oupu (8 6) ON OFF Sar operaion indicaor Li No li Dela operaion indicaor Li No li Nomenclaure Sar operaion indicaor (green) Dela operaion indicaor (orange) Scale range display windows Time uni display (sec is fixed) Time seing knob (for seing sar operaion ime) Sar operaion ime range selecor (selec one from 6, 12, 60, and 120 a full scale) Sar-dela ransfer ime selecor (selec one from 0.05 s, 0.1 s, 0.25 s, and 0.5 s) Sar-dela ransfer ime display window Solid-sae Sar-dela Timer H3CR-G 35

36 Dimensions Noe: All unis are in millimeers unless oherwise indicaed (78.0) dia x pins Dimensions wih Se Ring dia. Dimensions wih Fron Connecing Socke P2CF-08-@ Time seing ring Panel cover Dimensions wih Back Connecing Socke P3G H3CR-G8@L 101.3* 99 H3CR- G8@L P2CF-08 P2CF-08-E 2.3* Y92F-30 P3G-08 (When Y92A-48G mouned) *These dimensions vary wih he kind of DIN-rail (reference value). 36 Solid-sae Sar-dela Timer H3CR-G

37 Solid-sae OFF-delay Timer H3CR-H DIN 48 x 48-mm OFF-delay Timer Long power OFF-delay imes; S-series: up o 12 seconds, M-series: up o 12 minues. Models wih forced-rese inpu are available. 11-pin and 8-pin models are available. Timers Model Number Srucure Model Number Legend H3CR @ Classificaion H: OFF-delay imer 2. Configuraion None: 11-pin socke 8: 8-pin socke Lis of Models 3. Inpu None: Wihou rese inpu R: Wih rese inpu 4. Dimensions L: Long-body model 5. Supply Volage 6. Time Range AC: 100 o 120 VAC S: 0.05 o 12 s AC: 200 o 240 VAC M: 0.05 o 12 min 48DC: 48 VDC DC: 100 o 125 VDC Noe: This model number legend includes combinaions ha are no available. Before ordering, please check he Lis of Models below for availabiliy. Inpu Oupu Supply volage S-series M-series 11-pin models 8-pin models 11-pin models 8-pin models Wihou DPDT 100 o 120 VAC --- H3CR-H8L AC S --- H3CR-H8L AC M rese 200 o 240 VAC H3CR-H8L AC S H3CR-H8L AC M inpu 24 VAC/DC H3CR-H8L 24AC/DC S H3CR-H8L 24AC/DC M 48 VDC H3CR-H8L 48DC S H3CR-H8L 48DC M 100 o 125 VDC H3CR-H8L DC S H3CR-H8L DC M Wih 100 o 120 VAC H3CR-HRL AC S --- H3CR-HRL AC M --- rese inpu 200 o 240 VAC H3CR-HRL AC S H3CR-HRL AC M 24 VAC/DC H3CR-HRL 24AC/DC S H3CR-HRL 24AC/DC M 48 VDC H3CR-HRL 48DC S H3CR-HRL 48DC M 100 o 125 VDC H3CR-HRL DC S H3CR-HRL DC M SPDT 100 o 120 VAC --- H3CR-H8RL AC S --- H3CR-H8RL AC M 200 o 240 VAC H3CR-H8RL AC S H3CR-H8RL AC M 24 VAC/DC H3CR-H8RL 24AC/DC S H3CR-H8RL 24AC/DC M 48 VDC H3CR-H8RL 48DC S H3CR-H8RL 48DC M 100 o 125 VDC H3CR-H8RL DC S H3CR-H8RL DC M Solid-sae OFF-delay Timer H3CR-H 37

38 Accessories (Order Separaely) Name/specificaions Noe: 1. Y92A-48G is a finger safe erminal cover which is aached o he P3G-08 or P3GA-11 Socke. 2. Hold-down Clips are sold in ses of wo. Models Flush Mouning Adaper Y92F-30 Y92F-70 Y92F-71 Mouning DIN-rail 50 cm (l) x 7.3 mm () PFP-50N 1 m (l) x 7.3 mm () PFP-100N 1 m (l) x 16 mm () PFP-100N2 End Plae PFP-M Spacer PFP-S Proecive Cover Y92A-48B DIN-rail Mouning/ 8-pin P2CF-08 Fron Connecing Socke 8-pin, finger safe ype P2CF-08-E 11-pin P2CF pin, finger safe ype P2CF-11-E Back Connecing Socke 8-pin P3G-08 8-pin, finger safe ype P3G-08 wih Y92A-48G (See noe 1) 11-pin P3GA pin, finger safe ype P3GA-11 wih Y92A-48G (See noe 1) Hold-down Clip (See noe 2) For PL08 and PL11 Sockes Y92H-1 For PF085A Socke Y92H-2 Specificaions General Iem H3CR-H8L H3CR-H8RL H3CR-HRL Operaing/Rese mehod Insananeous operaion/time-limi Insananeous operaion/time-limi rese/forced rese rese Pin ype 8-pin 11-pin Inpu ype --- No-volage Oupu ype Relay oupu (DPDT) Relay oupu (SPDT) Relay oupu (DPDT) Mouning mehod DIN-rail mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds Conforms o EN and IEC (VDE0110) 4kV/2. Oupu caegory according o EN Time Ranges Time uni S-series M-series s (sec) min (min) Seing o o o o 12 Min. power ON ime 0.1 s min. 2 s min. Time-up operaion repea period 3 s min. Forced-rese repea period 3 s min. Noe: 1. If he above minimum power ON ime is no secured, he H3CR may no operae. Be sure o secure he above minimum power ON ime. 2. Do no use he Timer wih a repea period of less han 3 s. Doing so may resul in abnormal heaing or burning. Refer o Safey Precauions (H3CR-H) on page 1-44 for deails. 38 Solid-sae OFF-delay Timer H3CR-H

39 Raings Raed supply volage (See noe 1) 100 o 120 VAC (50/60 Hz), 200 o 240 VAC (50/60 Hz), 24 VAC/VDC (50/60 Hz), 48 VDC, 100 o 125 VDC Operaing volage range 85% o 110% of raed supply volage No-volage inpu (See noe 2) ON-impedance: 1 kω max. ON residual volage: 1 V max. OFF impedance: 500 kω min. consumpion 100 o 120 VAC: approx VA (0.22 W) a 120 VAC 200 o 240 VAC: approx VA (0.3 W) a 240 VAC 24 VAC/DC: approx VA (0.15 W) a 24 VAC approx. 0.1 W a 24 VDC 48 VDC: approx W a 48 VDC 100 o 125 VDC: approx. 0.5 W a 125 VDC Conrol oupus Conac oupu: 5 A a 250 VAC/30 VDC, resisive load (cosφ = 1) Noe: 1. A power supply wih a ripple of 20% max. (single-phase power supply wih full-wave recificaion) can be used wih each DC Model. 2. For conac inpu, use conacs which can adequaely swich 1 ma a 5 V. Characerisics Accuracy of operaing ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 0.6 and 1.2 s) ime Seing error ±5% FS ±50 ms max. Operaion sar volage 30% max. of raed volage Influence of volage ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 0.6 and 1.2 s) Influence of emperaure ±1% FS max. (±1% FS ±10 ms max. in ranges of 0.6 and 1.2 s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC, 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) 2,000 VAC, 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance Noe: Refer o he Life-es Curve on page kv (beween power erminals) for 100 o 120 VAC, 200 o 240 VAC, 100 o 125 VDC; 1 kv for 24 VAC/DC, 48 VDC 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 120 VAC, 200 o 240 VAC, 100 o 125 VDC; 1.5 kv for 24 VAC/DC, 48 VDC ±1.5 kv (beween power erminals) and ±600 V (beween inpu erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise); ±1 kv (beween power erminals) for 48 VDC Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude for 2 hrs each in hree direcions Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude for 10 min each in hree direcions Desrucion: 980 m/s 2 hree imes each in six direcions Malfuncion: 98 m/s 2 hree imes each in six direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 10 million operaions min. (under no load a 1,200 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,200 operaions/h) (See noe) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC : 6 kv conac discharge (level 3) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: IEC : 10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves: IEC : 10 V/m (900±5 MHz) (level 3) Immuniy Conduced Disurbance: IEC : 10 V (0.15 o 80 MHz) (level 3) Immuniy Burs: IEC : 2 kv power-line (level 3) 2 kv I/O signal-line (level 4) Immuniy Surge: IEC : 1 kv line o line (level 3) 2 kv line o ground (level 3) Case color Ligh Gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 120 g Timers Solid-sae OFF-delay Timer H3CR-H 39

40 Life-es Curve 10,000 Swiching operaions (x 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC for H3CR-H8L/-HRL and 100 ma a 5 VDC for H3CR-H8RL (failure level: P). Load curren (A) Connecions Block Diagrams Wihou Rese Inpu (H3CR-H8L) Time range/ uni selecor AC (DC) inpu supply Oscillaion Couning Oupu failure deecion Indicaor LCD Oupu indicaor Wih Rese Inpu (H3CR-H8RL/-HRL) Time range/ uni selecor AC (DC) inpu supply Oscillaion Couning Oupu failure deecion Indicaor LCD Oupu indicaor Rese inpu Inpu I/O Funcions Inpus Rese Turns off he conrol oupu and reses he elapsed ime. Oupus Conrol oupu Operaes insananeously when he power is urned on and ime-limi reses when he se ime is up afer he power is urned off. 40 Solid-sae OFF-delay Timer H3CR-H

41 Terminal Arrangemen Noe: DC models, including 24 VAC/DC models, have polariy. 8-pin Models Wihou Rese Inpu (H3CR-H8L) Wih Rese Inpu (H3CR-H8RL) Rese inpu Timers supply supply Noe: Leave erminal 3 open. Do no use hem as relay erminals. 11-pin Model Wih Rese Inpu (H3CR-HRL) Rese inpu supply Noe: Leave erminal 6 open. Do no use hem as relay erminals. Solid-sae OFF-delay Timer H3CR-H 41

42 Operaion Timing Char : Se ime R: Minimum power ON ime (S-series: 0.1 s min.; M-series: 2 s min.) If he power ON ime is less han his value, he Timer may no operae (i.e., oupu may no urn ON). Model H3CR-H8L (See noe) ON OFF R Timing char R Oupu (1 3) Oupu (1 4) Oupu (8 6) Oupu (8 5) H3CR-H8RL Oupu indicaor (See noe) Li No li ON OFF R R 0.05 s min s min. Rese inpu ON (Shor-ed) OFF (Open) Oupu (8 6) Oupu (8 5) H3CR-HRL Oupu indicaor (See noe) Rese inpu ON OFF Li No li R 0.05 s min. R 0.05 s min. Oupu (1 3) Oupu (1 4) Oupu (11 9) Oupu (11 8) Oupu indicaor Li No li Noe: If he power is urned ON unil he se ime is up, he imer will be reriggered. 42 Solid-sae OFF-delay Timer H3CR-H

43 Nomenclaure Oupu indicaor (red) Scale range display windows Time seing knob (for seing power OFF-delay ime) Timers Time range selecor (selec one from 0.6, 1.2, 6, and 12 a full scale) Time uni display S-series: sec M-series: min Dimensions Noe: All unis are in millimeers unless oherwise indicaed. H3CR-H8L H3CR-H8RL dia x pins H3CR-HRL dia x pins Dimensions wih Fron Connecing Socke P2CF-08-@/P2CF-11-@ Dimensions wih Back Connecing Socke P3G-08/P3GA H3CR-H8@L 101.3* 99 H3CR-HRL 112.2* H3CR- H8@L H3CR-HRL P2CF-08 P2CF-08-E 2.3* P2CF-11 P2CF-11-E 2.3* P3G-08 Y92F-30 (When Y92A-48G mouned) P3GA-11 Y92F-30 (When Y92A-48G mouned) *These dimensions vary wih he kind of DIN-rail (reference value). Solid-sae OFF-delay Timer H3CR-H 43

44 Safey Precauions (H3CR-H) Noe: The undermenioned is common for all H3CR-H models. Supplies The H3CR-H has a large inrush curren; provide sufficien power supply capaciy. If he power supply capaciy is oo small, here may be delays in urning ON he oupu. Wih he H3CR-H@RL, for he power supply of an inpu device, use an isolaing ransformer, of which he primary and secondary windings are muually isolaed and he secondary winding is no grounded. Correc 4*, 7 1*, 5 H3CR-H@RL Inpu erminal 10 7* 2 2* supply Wiring The H3CR-H has a high impedance. Therefore, he H3CR-H may no be rese if he H3CR-H is influenced by inducive volage. In order o eliminae any influence of inducive volage, he wires conneced o he H3CR-H mus be as shor as possible and should no be insalled alongside power lines. If he H3CR-H is influenced by inducive volage ha is 30% or more of he raed volage, connec a CR filer wih a capaciance of approximaely 0.1 μf and a resisance of approximaely 120 Ω or a bleeder resisor beween he power supply erminals. If here is any residual volage due o curren leakage, connec a bleeder resisor beween he power supply erminals. Operaion An inerval of 3 s minimum is required o urn on he H3CR-H afer he H3CR-H is urned off. If he H3CR-H is urned on and off repeaedly wih an inerval of shorer han 3 s, abnormal heaing or burning may occur in inernal elemens. * :H3CR-H8RL 3 s min. Inpu device Isolaion ransformer is required. Incorrec H3CR-H@RL 4*, 7 10, 7* 1*, 5 Inpu erminal 2, 2* supply * :H3CR-H8RL Oupu sae 1 Oupu sae 2 Afer he forced rese funcion of he H3CR-H is acivaed, an inerval of 3 s minimum is required o acivae he forced rese funcion again. If he forced rese funcion is acivaed repeaedly wih an inerval of shorer han 3 s, he inernal pars of he H3CR-H may deeriorae and he H3CR-H may malfuncion. Inpu device Isolaion ransformer Inpu/Oupu (H3CR-H@RL) An appropriae inpu is applied o he inpu signal erminal of he Timer when he inpu erminal for he inpu signal is shor-ed. Do no aemp o connec any inpu erminal o any erminal oher han he inpu erminal or o apply volage across oher han he specified inpu erminals or he inernal s of he Timer may be damaged. The H3CR-H@RL uses ransformerless power supply. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shor-ing due o a sneak curren o he ransformerless power supply. If inpu is made simulaneously from one inpu conac or a ransisor o he H3CR-H and a Timer whose common inpu erminals are used as power erminals, such as he H3CR-A, a shor- curren will be generaed. Eiher inpu hrough isolaed conacs, or isolae he power supply for one of he Timers. Rese inpu Oupu If i is required ha he oupu be urned on repeaedly wih an inerval of shorer han 3 s, consider use of he H3CR-A in mode D (signal OFF-delay). Ohers 3 s min. 3 s min. If he H3CR-H is dropped or experiences some oher kind of shock, because a laching relay is used for oupu, conacs may be reversed or go ino a neural sae. If he H3CR-H is dropped, reconfirm correc operaion. 4* H3CR-H@RL * 1* 5 2 2* Shor- curren G. 5 S. R H3CR-A 2 *: H3CR-H8RL ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers ino inches, muliply by To conver grams ino ounces, muliply by Ca. No. L084-E2-06 In he ineres of produc improvemen, specificaions are subjec o change wihou noice. 44 Solid-sae OFF-delay Timer H3CR-H

45 Common o all H3CR Noe: The undermenioned is common for all H3CR models. Basic Seing Seing of Selecors The selecors can be urned clockwise and counerclockwise o selec he desired ime uni, ime range, or operaing mode. Each selecor has a snap mechanism ha secures he selecor a a given posiion. Se he selecor a a posiion a which i is secured. Do no se i midway beween wo securing posiions or a malfuncion could resul from improper seing. H3CR-F Twin Timers A ime range (0 o 1.2, 0 o 3, 0 o 12, or 0 o 30) is seleced for ONand OFF-ime using he ime range selecor a he lower lef corner of he fron panel, and he seleced ime range appears wihin he plasic frame of he ime seing knob (= scale range display windows). Timers Selecion of Operaing Mode H3CR-A Mulifuncional Timer Turn he operaing mode selecor wih a screwdriver unil he desired operaing mode (H3CR-A/AP/AS: A, B, B2, C, D, or E, H3CR-A8/ A8S/A8E: A, B2, E or J, H3CR-A-300: G or J) appears in he display window locaed above he selecor. Time range selecor Operaing mode selecor Operaing mode display window Groove for screwdriver For ON-ime, he desired ime uni (sec, 10 s, min, and hrs, or 10 s, 10 min, hrs, and 10 h) is indicaed in he ON-ime uni display window a he lower righ corner of he fron panel and can be changed by urning he ON-ime uni selecor locaed below he ON-ime uni display window. (i.e., H3CR-A) Selecion of Time Uni and Time Range H3CR-A Mulifuncional Timer The desired ime uni (sec, min, hrs, or 10h) is displayed in he window below he ime seing knob by urning he ime uni selecor locaed a he lower righ corner of he fron panel. A ime range (1.2, 3, 12, or 30/2.4, 6, 24, or 60 for H3CR-A@-301) is seleced wih he ime range selecor a he lower lef corner of he fron panel, and he seleced ime range appears (in he window a he lower righ par) wihin he plasic frame of he ime seing knob. Time seing knob Time range selecor Time uni selecor Time uni display window Scale range display window ON-ime uni selecor For OFF-ime, he desired ime uni (sec, 10 s, min, and hrs, or 10 s, 10 min, hrs, and 10 h) is indicaed in he OFF-ime uni display window a he upper righ corner of he fron panel and can be changed by urning he OFF-ime uni selecor locaed below he OFF-ime uni display window. OFF-ime uni selecor Common o all H3CR 45

46 H3CR-G Sar-dela Timers A sar operaion ime range (0 o 6, 0 o 12, 0 o 60, or 0 o 120 seconds) is seleced wih he sar operaion ime range selecor a he lower lef corner of he fron panel. H3CR-H OFF-delay Timers A ime range (0 o 0.6, 0 o 1.2, 0 o 6, and 0 o 12) is seleced wih he ime range selecor a he lower lef corner of he fron panel. No ime uni selecor is available. When ordering he H3CR-H, specify S (for he second uni) or M (for he minue uni) for your H3CR-H. Sar operaion ime range selecor Time range selecor The ime required for swiching (0.05, 0.1, 0.25, or 0.5 second) from he sar operaion o he dela operaion of he H3CR-G can be seleced wih he sar-dela ransfer ime selecor a he lower righ corner of he fron panel. Seing of Time Use he ime seing knob o se he desired ime. Sar-dela ransfer ime selecor Using he Time Seing Ring for H3CR-A/-G Seing a Specific Time Moun he Panel Cover on he Timer, se he desired ime wih he ime seing knob, and place Time Seing Ring A ono he ime seing knob so ha he ime seing noch of Time Seing Ring A is in he cener of he rese lock posiion of he Panel Cover. Time seing noch Rese lock posiion Limiing he Seing Range Example: To se a range of 10 and 20 s. Moun he Panel Cover on he Timer, se he ime seing knob o 10 s (he lower limi of he seing range), and place Time Seing Ring C ono he ime seing knob so ha he sopper of Time Seing Ring C is on he righ edge of he rese lock posiion of he Panel cover. Nex, se he ime seing knob o 20 s (he upper limi of he seing range), place Time Seing Ring B ono he ime seing knob so ha he sopper of Time Seing Ring B is on he lef edge of he rese lock posiion of he Panel Cover. Sopper Rese lock posiion Time Seing Ring A Panel cover Time seing noch Seing posiion Time Seing Ring B Time Seing Ring C Panel cover Range Example: To se he ime o 10 s. 46 Common o all H3CR

47 Accessories (Order Separaely) (Common) Noe: The undermenioned is common for all H3CR models. Noe: All unis are in millimeers unless oherwise indicaed. Flush Mouning Adapor Y92F-30 Panel P3G Back Connecing Socke Timers Noe: The adapers for wo or more imers mouned in a verical line are differen in orienaion from hose mouned in a horizonal line. N can be obained as follows (n: he number of H3CR models arranged side by side) Wihou a Cover: N = (48n - 2.5) +1 /-0 Wih he Proecive Cover: N = (51n - 5.5) +1 /-0 Wih he Panel Cover: N = (50n - 4.5) +1 / R max. Panel Cuou (N) Y92F-70/-73 Panel P3G Back Connecing Socke Panel Cuou Adaper mouning hole Two, 4.5 dia. R0.5 max. 52 o ± o 66 76±0.2 45± (63.7) (See noe.) Y92F-71/-74 Noe: The value shown in parenheses is for he Y92F-70. Noe: The mouning panel hickness should be 1 o 3.2 mm. 56 Panel P3G Back Connecing Socke R0.5 max ± ± (63.7) (See noe.) Noe: The mouning panel hickness should be 1 o 3.2 mm. Noe: The value shown in parenheses is for he Y92F-71. Common o all H3CR 47

48 DIN-rail Mouning/Fron Connecing Socke P2CF-08 Eigh, M3.5 x 7.5 sems max max. P2CF-08-E (Finger Safe Terminal Type) Conforming o VDE0106/P100 Eigh, M3.5 x 7.5 sems Two, 4.5 dia. holes max Terminal Arrangemen/ Inernal Connecions (Top View) Surface Mouning Holes Two, 4.5 dia. or wo, M4 40± max. 1.3 Two, 4.5 dia. holes ± max max. DIN-rail Mouning/Fron Connecing Socke P2CF-11 Eleven, M3.5 x 7.5 sems max Terminal Arrangemen/ Inernal Connecions (Top View) Surface Mouning Holes 4 50 max max. Two, 4.5 dia. or wo, M4 40±0.2 P2CF-11-E (Finger Safe Terminal Type) Conforming o VDE0106/P100 Eleven, M3.5 x 7.5 sems max. Two, 4.5 dia. holes ± max max. 48 Common o all H3CR

49 Back Connecing Socke P3G dia. Terminal Arrangemen/ Inernal Connecions (Boom View) P3GA dia. Terminal Arrangemen/ Inernal Connecions (Boom View) Timers Finger Safe Terminal Cover Conforming o VDE0106/P100 Y92A-48G (Aachmen for P3G-08/P3GA-11 Socke) Twelve, 6.4 dia. holes x x Mouning DIN-rail PFP-100N, PFP-50N PFP-100N ,000 (500) 10 (See noe) 7.3± ±0.3 27±0.15 Noe: The value shown in parenheses are for he PFP-50N. End Plae PFP-M 15 (5) (See noe) ,000 Spacer PFP-S 5 35± M4 x 8 pan head screw Common o all H3CR 49

50 Proecive Cover Y92A-48B The proecive cover proecs he fron panel, paricularly he ime seing secion, agains dus, dir, and waer. I also prevens he se value from being alered due o accidenal conac wih he ime seing knob. Noe: 1. The Y92A-48B Proecive Cover is made of a hard plasic and herefore i mus be removed o change he imer se value. 2. The Proecive Cover canno be mouned if he Panel Cover (sold separaely) is used on he Timer. Y92A-48B Hold-down Clip Hold-down clips are sold in ses of wo. Y92H-7/-1 For PL08 and PL11 Sockes Y92H-8/-2 For PF085A Socke Time Seing Ring/Panel Cover for H3CR-A/-G There are hree ypes of Panel Covers (Y92P-48GL, Y92P-48GB, and Y92P-48GM), all of which are available in hree colors. Use he mos suiable ype of Panel Cover wih he design of he scaling plae according o he applicaion. When seing a given ime for he Timer, use of he Y92S-27 or Y92S-28 Time Seing Ring faciliaes he ime seing operaion and minimizes possible seing errors by operaors. The Y92F-73 or Y92-F-74 Flush Mouning Adaper or he Proecive Cover canno be used. The Time Seing Ring and Panel Cover should be used as a pair. Seing a specific ime Limiing he seing range Time Seing Ring A (Y92S-27) and Panel Cover (Y92P-48GL, -48GB, or -48GM) Time Seing Ring B or C (Y92S-28), and Panel Cover (Y92P-48GL, -48GB, or -48GM) Y92S-27 Time Seing Y92S-28 Time Seing Y92S-28 Time Seing C Y92P-48GL Ligh Gray Y92P-48GB Black Y92P-48GM Medium Gray 50 Common o all H3CR