Solid-State Timer H3CR-A. Ordering Information. 1/16 DIN Analog-Set Timer with Many Time Ranges, Operating Modes and Wide Supply Voltage Range

Transcription

1 R Solid-Sae Timer 1/16 DIN Analog-Se Timer wih Many Time Ranges, Operaing Modes and Wide Supply Volage Range H Field-selecable ime ranges from 0.05 second o 300 hours or 0.1 second o 600 hours H Selec 2-, 4-, or 6-funcion models o handle mos applicaions H Wide range AC/DC volage models (AC /DC or AC24-48/DC12-24) H PNP inpu now available H Shor, 80 mm (3.15 inch) panel mouning deph wih socke allows space-efficien conrol panel design H Choice of ligh gray, medium gray, or black panel covers o mach panel aesheics H UL, CSA, CE approved RC Ordering Informaion J TIMERS Timing funcion ON-Delay, Repea cycle (B, B2), Signal ON/OFF delay, Signal OFF-delay, Inerval Signal ON/OFFdelay, One-sho Signal ON/OFFdelay, One-sho ON-Delay, Repea cycle ON, Inerval, One-sho ON-Delay, Repea cycle ON, Inerval, One-sho Time range 0.05 s o 300 hr 0.05 s o 300 hr 0.1 s o 600 hr 0.05 s o 300 hr 0.1 s o 600 hr Terminal form 11-pin round 11-pin round 11-pin round 8-pin round 8-pin round Par number/ conac oupu AC /DC AC /DC AC /DC AC /DC AC /DC Par number/ ransisor oupu Par number/ ime-limiing and insananeous conac oupu AC24-48/DC12-48 P AC /DC P AC24-48/DC12-48 S AC24-48/DC AC24-48/DC AC24-48/DC AC24-48/DC S AC24-48/DC E AC /DC E AC24-48/DC AC24-48/DC

2 J MODEL NUMBER LEGEND jjj-j Terminal Form (Number of Pins) None: 11-pin models 8: 8-pin models 2. Inpu Type for 11-pin Models None: No-volage inpu (NPN ype) P: Volage inpu (PNP ype) 3. Oupu None: Relay oupu (DPDT) S: Transisor oupu (NPN/PNP universal use) E: Relay oupu (SPDT) wih insananeous relay oupu (SPDT) 4. Suffix 300: Dual mode models (signal ON/OFF-delay and one-sho) 301: Double ime scale (range) models (0.1 s o 600 h) J ACCESSORIES Descripion Par number Sockes 11-pin Boom surface or rack mouning, op screw erminals P2CF-11 Boom surface or rack mouning, op screw erminals, finger safe erminal conforms o P2CF-11-E VDE0106/P100 Back mouning, for use wih Y92F-30 mouning adaper, boom screw erminals P3GA-11 8-pin Boom surface or rack mouning, op screw erminals P2CF-08 Boom surface or rack mouning, op screw erminals, finger safe erminal conforms o P2CF-08-E VDE0106/P100 Back mouning, for use wih Y92F-30 mouning adaper, boom screw erminals P3G-08 Terminal cover for P3G sockes, conforms o VDE0106/P100 Y92A-48G Panel mouning adaper Fis behind panel, ideal for side-by-side insallaion. Use P3G_-_ sockes Y92F-30 Panel-mouning adaper (88 mm x 58 mm x 66 mm) Y92F-73 Panel-mouning adaper (58 mm x 50 mm x 66 mm) Y92F-74 Proecive cover Hard plasic cover proecs agains dus, dir and waer; no for use wih panel covers Y92A-48B NEMA 4 cover Waerproof fron cover Y92A-48N Colored panel covers Ligh gray (Munsell No. 5Y7/1) o mach case Y92P-48GL Medium gray (Munsell No. 5Y5/1) Y92P-48GM Black (Munsell No. N1.5) Y92P-48GB Time seing rings Used o lock-in a single seing; one ring, can be used wih Y92P panel covers Y92S-27 Used o lock-in a seing range; wo rings, can be used wih Y92P panel covers Y92S-28 Mouning rack DIN rail, 50 cm (1.64 f) lengh; 7.3 mm hick PFP-50N DIN rail, 1 m (3.28 f) lengh; 7.3 mm hick PFP-100N DIN rail, 1 m (3.28 f) lengh; 16 mm hick PFP-100N2 End plae PFP-M Spacer PFP-S 2

3 J RANGE AND OPERATION MODE SELECTION Oupu indicaor (orange) (Li when oupu is ON) indicaor (green) (Flashes when Timer operaes; li when Timer sops operaing) Operaing mode display window Operaing mode selecor Selec a mode from: A, B, B2, C, D, and E (, -AP, and -AS) A, B2, E and J (8, -A8S, and -A8E) G and J (-300) Time range selecor (selec one from 1.2, 3, 12, and 30 a full scale; wih he j-301, selec from 2.4, 6, 24, or 60 a full scale.) Operaing Modes Time seing knob (se ime) Scale range display windows Time uni display window Time uni selecor (selec one from sec, min, hrs, and 10h) Model /-AS P 8/-A8S 8E Operaing mode A: ON-delay B: Repea-cycle OFF sar B2: Repea-cycle ON sar C: Signal ON/OFF-delay D: Signal OFF-delay E: Inerval G: Signal ON/OFF-delay (Only for -300) J: One-sho (Only for -300) Time Ranges Noe: A: ON-delay (power sar) B2: Repea-cycle ON sar (power sar) E: Inerval (power sar) J: One-sho (power sar) When he ime seing knob is urned below 0 unil he poin where he ime seing knob sops, he oupu will operae insananeously a all ime range seings. Sandard (0.05-s o 300-h) Models Time uni s(sec) min h(hrs) x10 h (10 h) Full scale o o o12 seing 3 0.3o3 3o o12 12 o o30 30 o 300 Double (0.1-s o 600-h) Models Time uni s(sec) min h(hrs) x10 h (10 h) Full scale o o o24 seing 6 0.6o6 6o o24 24 o o60 60 o 600 3

4 Specificaions J RATINGS/CHARACTERISTICS Iem /A8 P 8E S/A8S Raed volage (See Noe 1.) Operaing volage rese consumpion 100 o 240 VAC/100 o 125 VAC VAC/12-48VDC Inpus Sar, rese and gae Conrol oupus VAC (50/60 Hz)/ VDC; VAC (50/60 Hz)/12-48 VDC 85% o 110% of raed volage (90% o 110% a 12 VDC) Minimum power-opening ime: 0.1 s A 240 VAC, 60 Hz Relay ON: approx. 2.1 VA (1.6 W) Relay OFF: approx. 1.3 VA (1.1 W) A 24 VDC Relay ON: approx. 0.8 W Relay OFF: approx. 0.2 W No-volage Inpu, NPN ype ( only) ON impedance: 1 kω ON residual volage: 1V max. Off impedance: 100 kω min. A 240 VAC, 60 Hz Relay ON: approx. 2.5 VA (2.2 W) Relay OFF: approx. 1.8 VA (1.7 W) (See Noe 3.) A 24 VDC Relay ON: approx. 0.9 W Relay OFF: approx. 0.3 W Volage Inpu, PNP ype Max. capaciy allowed beween inpu lines (erminal 6 and 7 or 6 and 8) is 1200µF Load connecable in parallel wih inpus (erminals 6 and 7 or 6 and 8). 100 o 240 VAC/100 o 125 VDC High (logic) level: 85 o 264 VAC/ 85 o VDC Low (logic) level: 0o10VAC/ 0o10VDC 24 o 48 VAC/ 12 o 48 VDC High (logic) level: VAC/ VDC Low (logic) level: 0o2.4VAC/ 0o1.2VDC VAC (50/60 Hz)/ VDC; VAC (50/60 Hz)/12-48 VDC (See Noe 2.) A 240 VAC, 60 Hz Relay ON/OFF: approx. 2 VA (1 W) A 24 VDC Relay ON/OFF: approx. 0.9 W VAC (50/60 Hz)/ VDC N/A A 24 VDC Oupu ON: 0.3 W Oupu OFF: approx. 0.2 W No-volage Inpu, NPN ype (S only) ON impedance: 1 kω ON residual volage: 1 V max. OFF impedance: 100 kω min. Time limi Relay oupu (DPDT) Relay oupu (DPDT) Relay oupu (SPDT) Transisor oupu (See Noe 5.) Insananeous Relay oupu (SPDT) Max. load 5 A a 240 VAC/30 VDC, resisive load (cos φ = 1) max. load 5 A a 250 VAC resisive load (cos φ =1) Min. load 10 ma a 5 VDC Residual volage 2Vmax. Repea accuracy ±0.2% FS max. (±0.2%± 10 ms max. in a range of 1.2 s) Seing error ±5% FS ±50 ms (See Noe 4.) 100 ma max. a 30 VDC max. Noe: 1. DC ripple rae: 20% max. if he power incorporaes a single-phase, full-wave recifier. 2. The 24 o 48 VAC/12 o 48 VDC model causes an inrush curren of approximaely 0.85 A. Take precauion when applying power o hese models, especially if here is a non-conac oupu like a sensor. 3. The values are for when he erminals 2 and 7 and erminals 10 and 6 are shored, and include he consumpion curren of he inpu circui. 4. The value is ±5% FS +100 ms o 0 ms max. when he C, D, or G mode signal of he P is OFF. 5. The inernal circuis are opically isolaed from he oupu. This enables universal applicaion as NPN or PNP ransisor.

5 Iem /A8 P 8E S/A8S Rese ime Rese volage Reseing sysem Indicaors Maerial Mouning mehod Connecion Weigh Approved sandards Min. power-opening ime: 0.1 s max. Min. pulse widh: 0.05 s (/-AS) 10% max. of raed volage OFF, exernal, self reseing (11-pin models); OFF (8-pin models) ON indicaor (green LED), Oupu ON indicaor (orange LED) Plasic case (ligh gray Munsell 5Y7/1) and knob (clear) DIN rack mouning, surface mouning, and flush mouning 11-pin () 8-pin (8) Approx. 90 g (3.17 oz) 11-pin 8-pin 11-pin (S) 8-pin (8S) UL508, CSA C22.2 No.14, NK, Lloyds Conforms o EN (VDE0435/P2021), IEC (VDE0110) 4kV/2, EN (conac oupu), and EN (non-conac oupu). Ambien Operaing - 10 C o55 C (14 F o 131 F) wih no icing emperaure Sorage - 25 C o65 C (-13 F o 149 F) wih no icing Ambien humidiy Operaing 35% o 85% Variaion due o volage ±0.2% FS max. (±0.2% ±10 ms max. in a range of 1.2 s) change Variaion due o ±1% FS max. (±1% ±10 ms max. in a range of 1.2 s) emperaure change Insulaon resisance 100 MΩ min. (a 500 VDC) Vibraion resisance Desrucion: 10 o 55 Hz wih 0.75-mm double ampliude each in 3 direcions for 2 hours each Malfuncion: 10 o 55 Hz wih 0.5-mm double ampliude each in 3 direcions for 10 minues each Shock resisance Desrucion: 1,000 m/s 2 (approx. 100G) 3 imes each in 6 direcions Malfuncion: 100 m/s 2 (approx. 10G) 3 imes each in 6 direcions Saic immuniy Malfuncion: 8 kv Desrucion: 15 kv Dielecric srengh 2,000 VAC (1,000 VAC for js), 50/60 Hz for 1 min beween curren-carrying meal pars and exposed non-curren-carrying meal pars 2,000 VAC (1,000 VAC for js), 50/60 Hz for 1 min beween conrol oupu erminals and operaing circui 2,000 VAC, 50/60 Hz for 1 min beween conacs of differen polariies 1,000 VAC, 50/60 Hz for 1 min beween conacs no locaed nex o each oher 2,000 VAC, 50/60 Hz for 1 min beween inpu and conrol oupu erminals and operaion circui Impulse wihsand volage 3 kv (beween power erminals) for 100 o 240 VAC/100 o 125 VDC; 1 kv for 24 o 48 VAC/12 o 48 VDC 4.5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 240 VAC/100 o 125 VDC; 1.5 kv for 24 o 48 VAC/12 o 48 VDC and 24 o 48 VAC/VDC EMC (EMI) EN Emission enclosure: EN55011 Group 1 class A Emission AC mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: EN : 4 kv conac discharge (level 2) 8 kv air discharge (level 3) Immuniy RF-inerference from AM radio waves: ENV50140: 10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from pulse-modulaed radio waves: ENV50204: 10 V/m (900±5 MHz) (level 3) Immuniy conduced disurbance: ENV50141: 10 V (0.15 o 80 MHz) (level 3) Immuniy burs: EN : 2 kv power-line (level 3) 2 kv I/O signal-line (level 4) Immuniy surge: EN : 1 kv line o line 2 kv line o ground (level 3) Degree of proecion IP40 (fron face) Life Mechanical 20,000,000 operaions min. (under no load a 1,800 operaions/h) expecancy Elecrical 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) 5

6 Engineering Daa 10,000 Swiching operaions (x 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ =0.4) 250 VAC/30 VDC (cosφ =1) Noe: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1 A can be swiched if L/R is 7 ms. In eiher case, a service life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma (100 ma for 8E) a 5 VDC (failure level: P). Load curren (A) Timing Chars Noe: 1. The minimum power-opening ime ( R ) is 0.1 s and he minimum pulse widh is 0.05 s. 2. The leer in he iming chars sands for he se ime and -a means ha he period is less han he ime se. /-AS/-AP Operaing mode Timing char A: ON-delay Sar Basic operaion Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor Sar Oupu B: Repea-cycle OFF sar Sar -a Basic operaion Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor Sar Oupu 6

7 Operaing mode Timing char B2: Repea-cycle ON sar -a Basic operaion Sar Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor Sar Oupu C: Signal ON/OFFdelay Sar -a -a -a Basic operaion Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor Sar Oupu D: Signal OFF-delay -a -a -a Sar Basic operaion E: Inerval Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor -a -a Sar Oupu Basic operaion Sar G: Signal ON/OFFdelay Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor Sar -a -a Sar Oupu Basic operaion Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor Sar Oupu 7

8 /-AS/-AP (coninued) Operaing mode Timing char J: One-sho oupu -a -a Basic operaion Sar Rese Oupu relay Oupu relay (NO) (Oupu indicaor) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Sar Oupu 1±0.6 s (Fixed) 8/-A8S Operaing mode Timing char A: ON-delay R R - a Basic operaion B2: Repea-cycle ON sar Oupu relay Oupu relay (NO) (oupu indicaor) indicaor -a R -a Oupu Basic operaion E: Inerval J: One-sho oupu Oupu relay Oupu relay (NO) (oupu indicaor) indicaor Oupu relay Oupu relay (NO) (oupu indicaor) indicaor Oupu relay Oupu relay (NO) (oupu indicaor) indicaor R R -a R R - a Oupu Basic operaion Oupu Oupu Basic operaion 1±0.6 s (Fixed) 8

9 8E Operaing mode Timing char A: ON-delay R R - a Oupu relay B2: Repea-cycle ON sar Oupu relay (NO) (oupu indicaor) Insananeous oupu relay Insananeous oupu relay (NO) indicaor -a R -a Basic operaion Oupu Oupu relay Oupu relay (NO) (oupu indicaor) Insananeous oupu relay Insananeous oupu relay (NO) Basic operaion Oupu indicaor E: Inerval R R - a J: One-sho oupu Oupu relay Oupu relay (NO) (oupu indicaor) Insananeous oupu relay Insananeous oupu relay (NO) indicaor R -a R Basic operaion Oupu Oupu relay Oupu relay (NO) (oupu indicaor) Insananeous oupu relay Insananeous oupu relay (NO) indicaor Basic operaion Oupu 1±0.6 s (Fixed) 9

10 J APPLICATION EXAMPLES A Mode: ON-delay ON-delay operaion (A mode) is a basic mode. 1. -ON Sar/-OFF Rese The power-on sar/-off rese operaion is a sandard operaing mehod. The sar erminals are conneced. Timing sars when power is applied. The oupu is energized when he accumulaed ime equals he se ime. The oupu relay or ransisor remains energized unil power is disconneced or a rese inpu is applied. The minimum reseing ime is 0.1 second. 3. Cumulaive Timing Using he Gae Inpu wih ON-Delay Wih a gae signal, he -ON sar operaion and Signal sar operaion can be conrolled (he operaion can be inerruped). When he gae signal is closed, iming is emporarily sopped. When he gae signal opens, iming resumes a he poin of inerrupion. The gae inpu erminal permis he imer o sum up imes 1 and 2 as shown in he iming char. (2 and 10) :seime (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu:no (9 and 11) NO (1 and 3) indicaor Exernally shor-circuied Flashing Li Sar (2 and 6) Gae (2 and 5) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Gae signal (The operaion is inerruped wih he gae signal if he Timer deecs an abnormal signal.) Li Exernally shor-circuied 2. Signal Sar/Signal Rese The signal sar/signal rese operaion is useful for remoe conrol of he Timer. is applied coninuously. Timing sars a he leading edge of he sar inpu. The oupu relay is energized when he accumulaed ime equals he se ime. Subsequen sar signals ha occur during or afer iming will no be acceped. The oupu relay or ransisor will remain energized unil a rese inpu is applied or power is inerruped. The minimum signal inpu is 0.05 second. (2 and 10) Sar (2 and 6) Rese (2 and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Sar signal (remoe conrol possible) Rese signal (remoe conrol possible) ( coninuously supplied) 10

11 B/B2 Mode: Repea Cycle The repea cycle operaion in he B and B2 modes can be effecively applied o lamp or buzzer (ON and OFF) alarms or he monioring of an inermien operaion wih a display. 1. -ON Sar/-OFF Rese The sar erminals are conneced. Timing sars when power is applied. The oupu relay or ransisor operaes according o mode B (OFF/ON/OFF paern) or mode B2 (ON/OFF/ON paern), whichever is se. The cycle repeas unil a rese inpu is applied or power is disconneced. C Mode: Signal ON/OFF-delay The Signal ON-/OFF-delay operaion (C mode) is useful for he conrol of disribuion of producs on a producion line ino boxes by he specified number or ime. 1. -ON Sar/Insananeous Operaion/Time-limi Rese The iming cycle sars when power is applied. When he imer reaches se poin, he oupu saus changes and holds ha saus unil power urns OFF o rese he imer. Minimum rese ime is 0.1 second. (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Sar signal (NC o NO) Exernally shor-circuied 2. Signal Sar/Signal Rese If here is an abnormal signal, flashing sars. When he abnormal condiion is resored, a rese signal sops he display flashing. is coninuously applied. The ON/OFF cycle is iniiaed a he leading edge of he sar inpu. In Mode B he oupu relay or ransisor will be OFF for he se ime and hen ON for he se ime, creaing an operaion paern of OFF/ON/OFF. In Mode B2 he oupu relay or ransisor will urn ON for he se ime and hen OFF for he se ime, creaing an operaion paern of ON/OFF/ON. This cycle will be repeaed unil a rese inpu is applied or power is disconneced. The minimum signal inpu ime is 0.05 second. (2 and 10) 2. Signal-ON-OFF Sar/Insananeous Operaion/Time-limi Rese is coninuously applied. The firs iming cycle begins when he inpu signal is applied, he second when i is removed. The oupu relay or ransisor is energized when he lapsed ime from he firs iming cycle equals he se poin. The oupu remains energized unil he lapsed ime of he second iming cycle equals he se poin. The minimum signal inpu ime is 0.05 second. (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Sar (2 and 6) Rese (2 and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Sar signal Rese signal Li Flashing Li indicaor Li Flashing Li Flashing Li Flashing Li Sar signal (The operaion sars wih he signal ON or OFF) ( coninuously supplied) ( coninuously supplied) 11

12 3. Signal Sar/Insananeous Operaion/Time-limi Rese is coninuously applied. The oupu relay is energized a he leading edge of he sar inpu. Timing sars a he railing edge of he sar inpu. The oupu relay is de-energized when he accumulaed ime equals he se ime. The minimum signal inpu ime is 0.05 second. E Mode: Inerval 1. Signal Sar/Insananeous Operaion/Time-limi Rese This funcion is useful for he repeiive conrol such as he filling of liquid for a specified period afer each Signal sar inpu. Timing begins on he leading edge of he sar signal. The conrol oupu is only energized during iming. The imer is rese when a rese signal is applied. (2 and 10) Sar (2 and 6) (2 and 10) Conrol oupu: NC (8 and 11) NC (1 and 4) Sar (2 and 6) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Sar signal (NO o NC o NO) Sar signal ( coninuously supplied) D Mode: Signal OFF-delay Signal OFF-delay operaion (D mode) can be effecively used o keep a load operaing for a cerain period. For example, his funcion enables he cooling fan for a lamp or heaer o operae for a cerain period afer he lamp or heaer is swiched OFF. -ON Sar/Insananeous Operaion/Time-limi Rese is coninuously applied. The oupu relay is energized a he leading edge of he sar inpu. Timing sars a he railing edge of he sar inpu. The oupu is de-energized when he accumulaed ime equals he se ime. The minimum rese ime is 0.1 second. ( coninuously supplied) 2. -ON Sar/Insananeous Operaion/Time-limi Rese Timing begins on he leading edge of he sar signal. The conrol oupu is only energized during iming. The imer is rese when a rese signal is inerruped. (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Sar signal (NC o NO) indicaor Li Flashing Li Sar signal (NC o NO) 12

13 Dimensions Uni: mm (inch) J TIMERS 11-Pin P S 8-Pin 8 8S 8E 48 (1.89) 15 (0.59) 66.6 (2.62) (1.89) 39 (1.54) dia x 44.8 (1.76 x 1.76) Dimensions wih Y92S Se Ring and Y92P Panel Cover 50 (1.97) 16.5 (0.65) 50 (1.97) 42 (1.65) dia. Time Seing Ring Panel cover J PANEL-MOUNTING ADAPTERS Dimensions wih Panel-Mouning Adaper Y92F-30 Panel Y92F-30 Adaper P3Gj Socke 58 (2.28) 52 (2.05) (1.89) Panel Cuou Noe: 1. The Adapers for wo or more imers mouned in a verical line are differen in orienaion from hose mouned in a horizonal line. N can be obained as follows (n: he number of H3CR models arranged side by side) Wihou a Cover: N = (48n - 2.5) +1 / - 0 Wih he Proecive Cover: N = (51n - 5.5) +1 / - 0 Wih he Panel Cover: N = (50n - 4.5) +1 / The mouning panel hickness should be 1 o 5 mm. 0.5 R max (N) 13

14 Dimensions wih Panel-Mouning Adaper Y92F-73 Panel Panel Cuou Adaper mouning hole Two, 4.5 dia. R0.5 max. 52 o (3.46) 45± o 66 76±0.2 45± (2.28) Dimensions wih Panel-Mouning Adaper Y92F-74 Noe: The mouning panel hickness should be 1 o 3.2 mm. 56 (2.20) Panel R0.5 max (2.28) 45± (2.68) ± Noe: The mouning panel hickness should be 1 o 3.2 mm. J TRACK MOUNTING Dimensions wih Fron-Connecing Socke P2CF-08/P2CF-11 P2CF-08-E/P2CF-11-E 100.8* (3.97) S 98.5 (3.88) 89.9* (3.54) 8j 87.6 (3.45) P2CF-11(E) 2.3* (0.09) P2CF-08(E) 2.3* (0.09) *These dimensions vary wih he kind of DIN rack (reference value). J PANEL MOUNTING Dimensions wih Back-Connecing Socke P3G-08/P3GA (0.59) 80 (3.15) 15 (0.59) 75 (2.95) S + Adaper Y92F-30 P3GA-11 8j + Adaper Y92F-30 P3G-08 14

15 J ACCESSORIES (ORDER SEPARATELY) Track Mouning/ Fron-Connecing Socke P2CF Eigh, (0.31) M3.5 x 7.5 sems 3 (0.12) 4.5 (0.18) Terminal Arrangemen/ Inernal Connecions (Top View) Surface Mouning Holes Two,4.5dia.orwo,M4 70 max. (2.76) 4 (0.16) 50 max. (1.97) Two, 4.5 dia. holes 20.3 max. (0.80) 35.4 (1.39) 40±0.2 P2CF-08-E Socke (Finger-Safe Terminal Type) Conforming o VDE0106/P100 Eigh M3.5 X 7.5 sems max. Two, 4.5 dia. holes ± max max. P2CF-11 Socke Eleven, M3.5 x 7.5 sems 7.8 (0.31) 3 (0.12) 4.5 (0.18) Two, 4.5 dia. mouning holes 4 (0.16) 70 max. (2.76) 50 max. (1.97) Two, 4.5 dia. holes 31.2 (1.23) max (1.39) 40±0.2 P2CF-11-E Socke (Finger-Safe Terminal Type) Conforming o VDE0106/P100 Eigh M3.5 X 7.5 sems max. Two, 4.5 dia. holes ± max (1.23) max. 15

16 Back-Connecing Socke P3G dia. (1.06) Terminal Arrangemen/ Inernal Connecions (Boom View) 45 (1.77) P3GA (1.77) 27 dia. (1.06) 4.9 (0.19) 17 (0.67) 45 (1.77) 25.6 (1.01) 45 (1.77) 4.5 (0.18) 16.3 (0.64) 6.2 (0.24) J PROTECTIVE COVERS Finger-Safe Terminal Cover for P3G(A) Conforming o VDE0106/P100 Y92A-48G Twelve, 6.4 dia. holes x x Y92A-48B The proecive cover proecs he fron panel, paricularly he ime seing secion, agains dus, dir, and waer. I also prevens he se value from being alered due o accidenal conac wih he ime seing knob. Noe: 1. The Y92A-48B Proecive Cover is made of a hard plasic and herefore i mus be removed o change he imer se value. 2. The Proecive Cover canno be mouned if he Panel Cover (sold separaely) is used on he Timer. 3. When using a fron cover for flush mouning, use he Y92F-30 Adaper. The Y92F-73 or Y92F-74 Flush Mouning Adaper canno be used. Y92A-48B 16

17 Time Seing Ring/Panel Cover There are hree colors of Panel Covers (Y92P-48GL (ligh gray), Y92P-48GB (black), and Y92P-48GM (medium gray). Use he mos suiable ype of Panel Cover wih he design of he scaling plae according o he applicaion. When seing a given ime for he Timer, use of he Y92S-27 or Y92S-28 Time Seing Ring faciliaes he ime seing operaion and minimizes possible seing errors by operaors. The Y92F-73 or Y92F-74 Panel-Mouning Adaper or he Y92A-48B Proecive Cover canno be used. Y92S-27 Time Seing A Y92S-28 Time Seing B Y92S-28 Time Seing C Y92P-48GL Ligh Gray The Time Seing Ring and Panel Cover should be used as a pair. Seing a specific ime Limiing he seing range Y92P-48GB Black Time Seing Ring A (Y92S-27) and Panel Cover (Y92P-48GL, -48GB, or -48GM) Time Seing Ring B or C (Y92S-28), and Panel Cover (Y92P-48GL, -48GB, or -48GM) Y92P-48GM Medium Gray Hold-Down Clip Y92H-7 For PL08 and PL11 Sockes Y92H-8 For PF085A Socke J MOUNTING TRACK PFP-100N, PFP-50N PFP-100N2 4.5 (0.18) 7.3± ±0.3 27± (0.18) 35± (0.63) 29.2 (1.15) * L 1 (0.04) L 1 (0.04) 1.5 (0.06) L: Lengh 1 m PFP-100N 50 cm PFP-50N 1 m PFP-100N2 End Plae PFP-M 10 (0.39) 6.2 (0.24) 1.8 (0.07) Spacer PFP-S 5 (0.20) 16 (0.63) (1.97) (1.39) 44.3 (1.74) 34.8 (1.37) (0.05) (0.45) 10 M4 x 8 (0.39) 4.8 (0.19) pan head screw 16.5 (0.65) 17

18 Connecions J INPUT/OUTPUT FUNCTIONS Models, P and S Name Type Descripion Sar inpu* No-volage conac closure Iniiaes iming Rese inpu No-volage conac closure Inerrups ime measuremen and reses he operaion o sar. No ime measuremen is made and he conrol oupu is OFF while he rese inpu is ON. Gae inpu No-volage conac closure Inhibis ime measuremen. Timing resumes when he gae inpu is urned OFF. Conrol oupu Relay or ransisor Turns ON and OFF when he prese value is reached, according o he operaion mode seleced. Noe: *P models offer Sar inpu only and use a PNP volage inpu. Gae signal inpu ON OFF 1 2 Sar ON OFF Gae ON OFF Rese ON OFF Oupu relay ON OFF Noe: 1. This iming char indicaes he gae inpu in operaing mode A (ON-delay operaion). 2. The se ime is he sum of 1 and 2. J CONNECTION SUMMARY Par number Inpu erminal numbers erminal numbers Oupu erminal numbers Gae Sar Rese 0V AC (common), DC - AC (ho), DC+ Type COM NC NO Timed conac Timed conac P Timed conac Timed conac S Transisor (NPN/PNP) Timed conac Timed conac E Timed conac Insananeous conac 8S Transisor (NPN/PNP)

19 J TERMINAL ARRANGEMENT Noe: The delayed conac of convenional Timers was indicaed as The conac symbol of he is indicaed as 8). 11-pin Models (Conac Oupu) because is operaing mode is five muli-modes (four muli-modes for he 8-pin Models 8 (Conac Oupu) Rese inpu Sar inpu Gae inpu (-) (~) (+) (~) ( -)(~) (+)(~) S (Transisor Oupu) 8S (Transisor Oupu) Rese inpu Sar inpu Gae inpu (-) (~) (+) (~) ( -)(~) (+)(~) Noe: Terminals 1, 3, 4, and 8 are empy. Terminals 2, 5, 6, 7, and 10 are he same as for he. Noe: Terminals 1, 3, 4, and 5 are empy. Terminals 2 and 7 are he same as for he 8. P (Conac Oupu) 8E (Conac Oupu) Sar inpu (-) (~) (+) (~) ( -)(~) (+)(~) Noe: Terminal 5 is empy. 19

20 J INPUT CONNECTIONS /-AS The inpus of he /-AS are no-volage (shor-circui or open) inpus. No-volage Inpus No-conac Inpu Conac Inpu No-conac Inpu (Connecion o NPN open collecor oupu sensor.) 12 o 24 VDC (sensor power ) + DC power - (Connecion o a volage oupu sensor.) 12 o 24 VDC (sensor power ) + DC power - Sensor Timer 5 Gae 6 Sar 7 Rese Timer 5 Gae 6 Sar 7 Rese Sensor Timer 5 Gae 6 Sar 7 Rese 2 Inpu (0 V) 2 Inpu (0 V) 2 Inpu (0 V) Operaes wih ransisor ON Operaes wih relay ON Operaes wih ransisor ON P The sar inpu of he P is volage inpu. (Volage imposiion or open) Volage Inpus No-conac Inpu No-conac Inpu Conac Inpu (Connecion o PNP open (Connecion o NPN open collecor oupu sensor) collecor oupu sensor) 12 o 24 VDC 12 o 24 VDC (sensor power ) (sensor power ) Sensor + DC power - Timer 10 (+) 6 Sar 7 Inpu 0V 2 (-) Operaes wih PNP ransisor ON Sensor + DC power - Timer Operaes wih NPN ransisor ON 10 (+) 6 Sar 7 Inpu 0V 2 (-) AC power DC power Operaes wih relay ON Timer 10 (+) 6 Sar 7 Inpu 0V 2 (-) Noe: The inpu circui is isolaed from he power circui. Thus, an NPN ransisor can be conneced. Noe: Refer o he signal levels in he following able and be aware of he minimum applicable load of he relay. 20

21 Insallaion J CHANGING THE SETTING Do no change he ime uni, ime range, or operaion mode while he Timer is in operaion, or he Timer may malfuncion. The ime uni and ime range can be se wih he respecive selecors urned clockwise or counerclockwise. The selecors are noched so ha hey will snap when hey are properly se. Do no se he selecors midway beween noches, or he Timer may break or malfuncion. J POWER SUPPLIES Pay he umos aenion no o make misakes in polariy when wiring he Timer. The H3CR Series uses a ransformerless power. Do no ouch he inpu erminals while he volage is applied, or an elecric shock may be received. A DC power can be conneced if is ripple facor is 20% or less and he mean volage is wihin he raed operaing volage range of he Timer. Be aware ha he operaing volage will rise by 5% if he raed volage is applied o he Timer coninuously while he ambien emperaure is close o he maximum permissible ambien emperaure. For he power of an inpu device of he /-AS, use an isolaing ransformer wih he primary and secondary windings muually isolaed and he secondary winding no grounded. Example: The power erminal 2 of /-AS is a common erminal for inpu signals o he Timer. Do no disconnec he wires on erminal 2, or he inernal circuiry of he /-AS will be damaged. Close 5, 6, 7 G, S, R Inpu erminal An AC power can be conneced o he power inpu erminals wihou regard o polariy. A DC power mus be conneced o he power inpu erminals as designaed according o he polariy of he erminals. Make sure ha he volage is applied wihin he specified range, or he inernal elemens of he Timer may be damaged. Connec he power volage hrough a relay or swich in such a way ha he volage reaches a fixed value a once, or he Timer may no be rese, or a imer error may resul. Inpu erminal Circui Recifier circui Isolaing ransformer is no required. 21

22 J INPUT/OUTPUT Relaionship beween Inpu and Supply Circuis (/-AS) The /-AS uses ransformerless power. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shor-circuiing due o a sneak curren o he ransformerless power. If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no differ in phase, or he erminals will be shor-circuied o one anoher. Incorrec Conac or ransisor for exernal inpu signal Inpu erminal An appropriae inpu is applied o he inpu signal erminals of he /-AS when one of he inpu erminals is shor-circuied wih he common erminal (erminal 2) for he inpu signals. Do no aemp o connec he inpu erminal o any erminal oher han he common erminal or o apply volage across erminals oher han he specified inpu and common erminals, or he inernal circuiry of he Timer will be damaged. AC or DC power Inpu conac (2.) 5, 6, 7 G, S, R Inpu erminal (See Noe 1.) Shor-circui curren Correc Inpu erminal Inpu erminal Noe: 1. erminal 2 is a common erminal for inpu signals o he Timer. Never use erminal 10 as he common erminal for his purpose, or he inernal circui of he Timer will be damaged. 2. Do no connec a relay or any oher load beween hese erminals, or he inernal circui of he Timer will be damaged due o he high-ension volage applied o he inpu erminals. Relaionship beween Inpu and Supply Circuis (P) P Inpu erminal AC/DC power Inpu circui circui I is impossible o provide wo independen power swiches as shown below regardless of wheher he Timers are differen in phase. Inpu erminal Since he inpu circui and he power circui are configured independenly, he inpu circui can be urned ON or OFF irrespecive of he ON/OFF sae of he power. I mus be noed ha a volage equivalen o he power volage is applied o he inpu circui. When connecing a relay as an exernal signal inpu device, pay aenion o he following poins o preven shor-circuiing due o a sneak curren o he ransformerless power. Inpu erminal 22

23 If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no be differen in phase or he erminals will be shor-circuied o one anoher (refer o he figures below). Incorrec Conac or ransisor for exernal inpu signal CommonoAllModels The inpu wires mus be as shor as possible. If he floaing capaciy of wires exceeds 1,200 pf (approx. 10 m for cables wih 120 pf/m), he operaion will be affeced. Pay paricular aenion when using shielded cables. The js ransisor oupu is isolaed from he inernal circuiry by a phoocoupler. Therefore, eiher NPN or PNP oupu is possible. P The power circui of he Series (excep for js) is a swiching circui. If he power line conneced o he power circui has a ransformer wih high inducance, a couner-elecromoive volage will be induced. To suppress he volage, apply a CR filer o he power line. Do no se he dial o minimum in repea cycle mode (B, B2) or he conacs may be damaged. P Correc Conac or ransisor for exernal inpu signal P P 23

24 Operaion J BASIC SETTING Seing of Selecor The selecors can be urned clockwise and counerclockwise o selec he desired ime uni, ime range, or operaing mode. Each selecor has a snap mechanism ha secures he selecor a a given posiion. Se he selecor a a posiion a which i is secured. Do no se i midway beween wo securing posiions or a malfuncion could resul from improper seing. Operaing mode selecor Operaing mode display window J TIME SETTING RINGS Time seing rings allow he operaor o lock in a seleced, prese ime. They mus be used wih Y92P Panel Covers. Each ring fis snugly around he ime seing knob. A noch on he ring engages he ab on he panel cover o preven seing knob ravel. Omron offers wo ypes of ime seing rings in medium gray. The Y92S-27 seing ring is used for a single se poin. The Y92S-28 pair of rings are used o lock in wo se poins for a iming range. Y92S-27 Seing a Single Prese In his example, he ime seing will be locked a 10 minues: Selec iming funcion and se uni of measure o min. Insall he panel cover. Turn he ime seing knob o 10. Align he noch on he ring wih he ab hen press he ring ono he ime seing knob. Groove for screwdriver Time seing noch Rese lock posiion Time seing noch Seing posiion Selecion of Operaing Mode Turn he operaing mode selecor wih a screwdriver unil he desired operaing mode (/AP/AS: A, B, B2, C, D, or E, 8/A8S/A8E: A, B2, E or J, -300: G or J) appears in he display window locaed above he selecor. Selecion of Time Uni and Time Range The desired ime uni (sec, min, hrs, or 10h) is displayed in he window below he ime seing knob by urning he ime uni selecor locaed a he lower righ corner of he fron panel. A ime range (1.2, 3, 12, or 30/2.4, 6, 24, or 60 for j-301) is seleced wih he ime range selecor a he lower lef corner of he fron panel, and he seleced ime range appears (in he window a he lower righ par) wihin he plasic frame of he ime seing knob. Time Seing Ring Y92S-27 Panel cover Y92S-28 Limiing he Seing Range Example: To se he ime o 10 s. In his example, he iming range of 10 o 20 minues will be locked in using he wo rings in Y92S-28: Se he iming funcion and se uni of measure o min. Turn he seing knob o 10. Align he hinner ring s ab wih he righ side of he panel cover ab. Press he ring ono he ime seing knob o se he lower limi. Turn he ime seing knob o 20. Align he hicker ring s ab wih he lef side of he panel cover ab. Press he ring ono he ime seing knob o se he upper limi. Range Time seing knob Sopper Rese lock posiion Time range selecor Scale range display window Time uni selecor Time uni display window Time Seing Y92S-28 Time Seing Y92S-28 Panel cover Seing of Time Use he ime seing knob o se he desired ime. 24

25 Mouning J PANEL MOUNTING Using Y92F-30 Adaper Inser he imer hrough he panel cuou. Push he Y92F-30 adaper from he rear of he imer as far forward oward he panel as possible. Wire he P3Gjj socke, hen push i ono he rear of he imer. Then ighen he wo reaining screws. To release he adaper, lif he ab a he rear of he adaper. Several imers may be panel mouned close ogeher using Y92F-30 adaper as shown here. When mouning wo or more imers in a verical line, arrange he adapers so ha heir molded abs are posiioned on he righ and lef sides. When mouning wo or more imers in a horizonal line, arrange he adapers so ha heir molded abs are posiioned on he op and boom sides. Panel cuou for side-by-side mouning of wo imers Molded ab Molded ab J TRACK MOUNTING Using P2CF-jj Socke Mouning Removal The P2CF-jj socke has wo hooks ha secure he imer o he socke. Be sure o allow a leas 20 mm (0.79 in) clearance above and below he socke o gain access and o release he hooks for servicing and mainenance. Inser imer ino he socke. Lach hooks. Then clip rear of he socke o he rack. Push he boom ono he rack unil he lach hooks securely. Hook 20 mm (0.79 in) P2CF-11 or P2CF-08 socke Pull he lach on he socke wih a fla-blade screwdriver and remove he imer and socke as one uni. 25

26 Precauions J OPERATING ENVIRONMENT Do no use he Timer in he following locaions. D Locaions wih radical emperaure changes. D Locaions wih high humidiy ha may resul in condensaion. D Locaions wih excessive vibraion or shock. D D Locaions wih corrosive gas or dus. Locaions where he Timer is exposed o sprayed waer, oil, or chemicals. Organic solvens (such as pain hinner) as well as srong acid or alkali soluions will damage he ouer casing of he Timer. If he Timer is used in an area wih excessive elecrical noise, be sure o separae he Timer, wires, and inpu device as far as possible from he noise sources. Shield he inpu signal wiring o preven elecrical inerference. J VOLTAGE WITHSTAND TEST If he Timer is mouned o a conrol board, remove he Timer from he conrol board or shor-circui he conrol board circuiry before carrying ou a volage wihsand es beween he elecric circuiry and non-charged meal par of he Timer. This proecs he inernal circuiry of he Timer from damage. J PRECAUTIONS FOR EN (VDE) CONFORMANCE The Series, insalled as a buil-in imer, conforms o EN (VDE0435/P2021) provided ha he following condiions are saisfied. Make sure ha no volage is applied o any erminals before removing he Timer from he Socke. The oupu secion of he is provided only wih basic isolaion. Provide supplemenary basic isolaion on he load side conneced o he oupu so ha reinforced isolaion required by he EN (VDE) sandards will be ensured. The iself is designed under he following condiions: D Overvolage caegory III D Polluion degree 2 D Isolaion Operaion pars: Reinforced isolaion Wih clearance of 5.5 mm and creepage disance of 5.5 mm a 230 VAC Oupu: Basic isolaion (See Noe.) Wih clearance of 3 mm and creepage disance of 3 mm a 230 VAC Noe: The 11-pin model ensures basic isolaion by iself and also ensures basic isolaion wih he 11-pin model mouned o he OMRON P2CF-11 or P3GA-11 Socke. Connec he wo oupu conacs differen in polariy o he loads so ha hey will be he same in poenial. NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers o inches divide by R OMRON ELECTRONICS LLC OneEasCommerceDrive Schaumburg, IL OMRON OMRON ON -LINE Global - hp:// USA - hp:// Canada - hp:// OMRON CANADA, INC. 885 Milner Avenue Scarborough, Onario M1B 5V C a. N o. G C T MC N 1 3/ 02 S pec if ic a ions s ubjec o c hange w i hou no ic e. P r in ed in U. S. A. 26