Freestanding Christmas Village Diner

Transcription

1 Freestanding Christmas Village Diner #12686 / 1 Design / 12 Files Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen Front Wall FSA 3.03 X 7.37 in X mm 45,487 St Front Door FSA 3.65 X 3.03 in X mm 24,079 St Side Wall 1 FSA 3.61 X 3.03 in X mm 24,007 St Side Wall 2 FSA 3.61 X 3.03 in X mm 24,007 St Back Wall FSA 3.03 X 7.38 in X mm 46,387 St Inner Wall FSA 3.09 X 7.37 in X mm 26,268 St Roof FSL 4.87 X 8.00 in X mm 67,427 St Roof Arch Front FSA 2.06 X 6.62 in X mm 17,630 St Roof Arch Back FSL 1.34 X 6.64 in X mm 20,689 St Roof Top Snow FSA 3.14 X 7.84 in X mm 30,560 St Roof Top FSA 3.14 X 7.84 in X mm 39,572 St Foundation FSA 4.44 X 7.38 in X mm 20,706 St. It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

2 Listings below indicate color sample, stitching order and suggested thread color number. Most numbers indicate Isacord thread. Colors beginning with 7 refer to Yenmet Metallic and 9 refer to Isacord Multicolor Variegated Front Wall FSA n 1. Placement Stitch Front Door FSA Freestanding Christmas Village Diner Back Wall FSA Inner Wall FSA #12686 / 1 Design / 12 Files Roof Arch Back FSL n 1. Single Color Design Roof Top Snow FSA n 1. Roof Placement Stitch n 2. Roof Cut Line & Tackdown n 3. Snow Placement Stitch n 4. Snow Cut Line & Tackdown n 5. Lace Side Wall 1 FSA Side Wall 2 FSA Roof FSL n 1. Single Color Design Roof Arch Front FSA n 4. Lettering Roof Top FSA Foundation FSA FSA - Freestanding Applique FSL - Freestanding Lace It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

3 Freestanding Christmas Village Diner General Freestanding Lace Guidelines Supplies: General Embroidery Thread: 1. Hoop two layers of water-soluble stabilizer. Use the same embroidery thread in the bobbin as the needle. 2. Attach the hoop to the machine and select the design of your Needles: choice. Use an Organ 80/12 Titanium needle for extended needle life. 3. Stitch the design. Stabilizer: 4. Remove the hoop from the machine and the design from the Use water-soluble stabilizer or film water-soluble stabilizer. hoop. Trim excess stabilizer from the design. 5. Rinse away remaining stabilizer and allow it to dry. Handy Hints: For Stiffer Lace: Handy Hints: DO NOT rinse away all of the stabilizer for a stiffer lace. For 3D Lace Projects: Note that the thread may appear a shade darker if stabilizer is If item becomes too limp to work with, iron the lace pieces not removed completely. on the wrong side while applying spray starch. After ironing, If you happen to wash too much out, easily re-stiffen by spray again with starch and allow to dry completely. This will diluting some stabilizer scraps in water and dipping the item stiffen the lace pieces nicely and aid in construction. in the solution. A pair of tweezers, hemostats, stiletto or a tiny crochet hook For Very Soft Lace: can be extremely helpful when inserting the buttonettes Cut away excess stabilizer. Remove remaining stabilizer by into the eyelets. (Please see Diagram 1 for explanation of rinsing under warm running water until all traces of the buttonette and eyelet.) stabilizer are gone. NOTE: If lace should become too limp to Insert the tip of the alligator clamps, tweezers, hemostats or work with, dissolve stabilizer scraps in warm water and apply crochet hook into the eyelet, grasp the buttonette and pull to the lace. through the eyelet. Or a stiletto could be used to push the Drying Lace: buttonette through the eyelet. The lace looks best when left to dry completely. Lay lace Eyelet piece with right side down to dry. This will minimize the tendency for the lace to curl. Be sure to flatten the piece out entirely and allow ample time to dry. Diagram 1 Buttonette

4 Supplies: Embroidery Thread: Use the same embroidery thread in the bobbin as the needle. Needles: Use an Organ 80/12 Titanium needle for extended needle life. Stabilizer: Use water-soluble stabilizer or film water-soluble stabilizer. General Applique 1. Hoop two layers of OESD AquaMesh Stabilizer. 2. Attach the hoop to the machine and select the design of your choice. 3. Stitch the Placement Stitch. Photo 1 4. Place a piece of applique fabric over the Placement Stitch so that it is completely covered. 5. Stitch the Cut Line & Tackdown stitch. 6. Carefully cut away the excess applique fabric. Photo 2 7. Stitch the remainder of the design and repeat for any remaining pieces. Photo 3 8. Remove the hoop from the machine and the design from the hoop. 9. Trim excess stabilizer from the design. 10. Rinse away remaining stabilizer and allow it to dry face down to prevernt curling. Freestanding Christmas Village Diner General Freestanding Applique Guidelines Handy Hints Drying: Freestanding pieces look best when left to dry with right side down. This will minimize the tendency for a piece to curl. Be sure to flatten the piece out entirely and allow ample time to dry. For 3D Applique Projects: Adhere 1 layer of OESD StabilStick TearAway to the back of applique fabrics with temporary adhesive spray BEFORE hooping or placing down for tackdown and cut in place. This gives fabric a more rigid structure. A pair of alligator clamps, tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (See Diagram 1 for explanation of buttonette and eyelet.) Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. Or a stiletto could be used to push the buttonette through the eyelet. Eyelet Buttonette Diagram 1 Appliqué

5 Diner Summary Requires 1 Front Wall FSA Requires 1 Front Door FSA Requires 1 Side Wall 1 FSA Requires 1 Side Wall 2 FSA Requires 1 Back Wall FSA Requires 1 Inner Wall FSA Requires 1 Roof FSL Requires 1 Roof Arch Front FSA Requires 1 Roof Arch Back FSL Requires 1 Roof Top Snow FSA OR 1 Roof Top FSA Requires 1 Foundation FSA Freestanding Christmas Village Diner Diner Assembly Attach the six buttonettes of Front Wall to the six eyelets on Sides and PHOTO 1 Attach the six buttonettes on Door to the six eyelets on Front Wall PHOTOS 2 & 3 Photo 1 Photo 2 Photo 3 Attach just three buttonettes on Back Wall to Side Don t attach both sides just yet. Leave one side open to help assembly later. PHOTO 4 Attach the seven buttonettes on Foundation to the eyelets of the Front Wall, both Sides Walls, the Door and Back Wall PHOTO 5 Attach Both Roof Top Arch and to Roof Top Snow by lining up the six Photo 4 Photo 5

6 Freestanding Christmas Village Diner buttonettes on with the six eyelets on Roof Top Snow, and attaching the five buttonettes from to the five eyelets on the other side of Roof Top Snow. PHOTOS 6 & 7 Attach the two buttonettes on Inner Wall to the two corresponding eyelets on Roof FSL PHOTOS 8 & 9 Attach the nine buttonettes on the Arched Roof assembly to the corresponding eyelets on the Roof FSL Photo 6 Photo 7 Photo 8 Photo PHOTOS 10 & 11 Lower the Roof Top Assembly down into the structure photo 12 and attach the four buttonettes on the Inner Wall to the corresponding eyelets on both Side Walls. (It helps to start with the bottom buttonettes first) PHOTO 13 Photo 10 Photo 11 Photo 12 Photo 13 Then attach the twelve buttonettes from the structure Walls and Door to the elyelets on the FSL Roof. (It helps to start with the buttonettes on the front of the structure then attach the Side walls then finishing with the Back Wall.) PHOTOS 14 & 15 Complete the Diner by attaching the last three buttonettes on the Back Wall to the three eyelets on PHOTO 16 Photo 14 Photo 15 Photo 16