Freestanding Pagoda #12564 / 10 Files

Transcription

1 #12564 / 10 Files Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen Pagoda Front Wall FSA 17,718 St. zr Pagoda Left Wall FSA 14,581 St. zr Pagoda Back Wall FSA 14,733 St. zr Pagoda Right Wall FSA 14,415 St. zr Pagoda Foundation FSA 3.71 X 3.71 in X mm 7,380 St. R Pagoda Roof & Wall 1 FSA 2.85 X 5.45 in X mm 21,225 St. zr L Pagoda Ceiling 1 FSL 2.95 X 2.95 in X mm 10,279 St. z Pagoda Roof & Wall 2 FSA 4.20 X 3.56 in X mm 19,447 St. zr Pagoda Ceiling 2 FSL 2.31 X 2.31 in X mm 5,924 St. z Pagoda Roof FSA 4.34 X 4.34 in X mm 33,149 St. zr Some solid It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

2 Listings below indicate color sample, stitching order and suggested thread color number. Most numbers indicate Isacord thread. Colors beginning with refer to YLI Fine Metallics, 7 refer to Yenmet Metallic, 8 refer to YLI Variations Variegated Thread and 9 refer to Isacord Multicolor Variegated Pagoda Front Wall FSA n 4. Door n 5. Swirls n 6. Light Red Door Trim n 7. Black Detail n 8. Cover Stitch & Lace n 9. Gold Detail Pagoda Left Wall FSA n 4. Swirls Pagoda Back Wall FSA n 4. Swirls #12564 / 10 Files Pagoda Right Wall FSA n 4. Swirls Pagoda Foundation FSA n 1. Placement Stitch n 2. Cut Line & Tackdown n 3. Cover Stitch Pagoda Roof & Wall 1 FSA n 1. Placement Stitch n 2. Cut Line & Tackdown n 3. Swirls n 4. Black Detail n 5. Cover Stitch & Lace n 6. Silver Detail Pagoda Ceiling 1 FSL n 1. Single Color Design Pagoda Roof & Wall 2 FSA n 3. Window n 4. Light Red Window Trim n 7. Silver Detail n 8. Gold Detail Pagoda Ceiling 2 FSL n 1. Single Color Design Pagoda Roof FSA n 1. Placement Stitch n 2. Cut Line & Tackdown n 3. Black Detail n 4. Cover Stitch & Lace n 5. Silver Detail Isacord / Yenment Metallic Thread Colors Used in Collection # White 0020 Black 1730 Persimmon 1800 Wildfire 7009 White Silver Metallic 7014 Gold Metallic FSA - Freestanding Appliqué FSL - Freestanding Lace It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

3 General Freestanding Appliqué Guidelines Supplies: Embroidery Thread: Use the same embroidery thread in the bobbin as the needle. Needles: Use an Organ 80/12 Titanium needle for extended needle life. Stabilizer: Use water-soluble stabilizer or film water-soluble stabilizer. General Appliqué 1. Hoop two layers of water-soluble stabilizer. 2. Attach the hoop to the machine and select the design of your choice. 3. Stitch the Placement Stitch. Photo 1 4. Place a piece of appliqué fabric over the Placement Stitch so that it is completely covered. 5. Stitch the Cut Line & Tackdown Stitch. 6. Carefully cut away the excess applique fabric. Photo 2 7. Stitch the remainder of the design and repeat for any remaining pieces. Photo 3 8. Remove the hoop from the machine and the design from the hoop. 9. Trim excess stabilizer from the design. 10. Rinse away remaining stabilizer and allow it to dry. Handy Hints For 3D Appliqué Projects: Adhere 2 layers of heavy weight stabilizer to the back of fabrics with temporary adhesive spray BEFORE hooping or placing down for tackdown and cut in place. This gives fabric a more rigid structure. A pair of tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (See Diagram 1 for explanation of buttonette and eyelet.) Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. Or a stiletto could be used to push the buttonette through the eyelet. Buttonette Diagram 1 Eyelet Appliqué 1 2 3

4 General Freestanding Lace Guidelines Supplies: General Embroidery Thread: 1. Hoop two layers of water-soluble stabilizer. Use the same embroidery thread in the bobbin as the needle. 2. Attach the hoop to the machine and select the design of your Needles: choice. Use an Organ 80/12 Titanium needle for extended needle life. 3. Stitch the design. Stabilizer: 4. Remove the hoop from the machine and the design from the Use water-soluble stabilizer or film water-soluble stabilizer. hoop. Trim excess stabilizer from the design. 5. Rinse away remaining stabilizer and allow it to dry. Handy Hints: For Stiffer Lace: DO NOT rinse away all of the stabilizer for a stiffer lace. Note that the thread may appear a shade darker if stabilizer is not removed completely. If you happen to wash too much out, easily re-stiffen by diluting some stabilizer scraps in water and dipping the item in the solution. For Very Soft Lace: Cut away excess stabilizer. Remove remaining stabilizer by rinsing under warm running water until all traces of the stabilizer are gone. Note: If lace should become too limp to work with, dissolve stabilizer scraps in warm water and apply to the lace. Drying Lace: The lace looks best when left to dry completely. Lay lace piece with right side down to dry. This will minimize the tendency for the lace to curl. Be sure to flatten the piece out entirely and allow ample time to dry. Diagram 1 Eyelet Handy Hints: For 3D Lace Projects: Adhere 2 layers of heavy weight stabilizer to back of fabrics with temporary adhesive spray before hooping or placing down for tackdown and cut in place. This gives fabric a more rigid structure. Rinsing out lace with very hot water can cause wrinkles in some fabrics after it has been embroidered. To prevent this, pre-shrink cotton fabric by washing it in warm water and drying it in a dryer. If item becomes too limp to work with, iron the appliqué pieces on the wrong side while applying spray starch. After ironing, spray again with starch and allow to dry completely. This will stiffen the lace pieces nicely and aid in construction. A pair of tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (Please see Diagram 1 for explanation of buttonette and eyelet.) Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. Or a stiletto could be used to push the buttonette through the eyelet. Buttonette

5 Summary Requires 1 Pagoda Front Wall FSA Requires 1 Pagoda Left Wall FSA Requires 1 Pagoda Back Wall FSA Requires 1 Pagoda Right Wall FSA Requires 1 Pagoda Foundation FSA Requires 4 Pagoda Roof & Wall 1 FSA Requires 1 Pagoda Ceiling 1 FSL Requires 4 Pagoda Roof & Wall 2 FSA Requires 1 Pagoda Ceiling 2 FSL Requires 1 Pagoda Roof FSA Supplies Isacord embroidery thread Fabric for appliqué Heavy weight cut away stabilizer or sticky back cut away stabilizer for appliqué Wash away stabilizer Embroidery machine Optional - Alligator clamps, tweezers, hemostats, stiletto or a tiny crochet hook Follow the General Freestanding Lace Guidelines and General Freestanding Appliqué Guidelines to stitch the required pieces as listed in the summary above for the pagoda. Build a Pagoda Attach the Pagoda Front Wall FSA ( ) to the Pagoda Left Wall FSA ( ) side by inserting the two buttonettes along the left side into the two eyelets on the right side. Continue attaching the Pagoda Back Wall FSA ( ) and the Pagoda Right Wall FSA ( ) pieces together in the same manner creating a flat piece. PHOTO 1 Attach the Pagoda Foundation FSA ( ) by inserting the buttonettes of the foundation into the eyelets along the bottom of the pagoda walls. PHOTO 2 Photo 1 Photo 2 Photo 3 Photo 4 Attach the remaining side of the pagoda walls to form a square. Set aside. Attach a Pagoda Roof & Wall 1 FSA ( ) to another Pagoda Roof & Wall 1 FSA ( ) by inserting the five buttonettes along the left side into the five eyelets on the right side. Continue attaching the pagoda roof & walls 1 together in the same manner creating an open piece. Attach the Pagoda Ceiling 1 FSL ( ) to the pagoda roof & wall 1 section by pulling the buttonettes from the ceiling piece into the corresponding eyelets on the middle section of the padoga roof & wall 1 section. PHOTO 3 Attach the remaining side of the pagoda roof & walls 1 to form a square. Set aside. PHOTO 4

6 Attach a Pagoda Roof & Wall 2 FSA ( ) to another Pagoda Roof & Wall 2 FSA ( ) by inserting the five buttonettes along the left side into the five eyelets on the right side. Continue attaching the pagoda roof & walls 2 together in the same manner creating an open piece. PHOTO 5 Attach the Pagoda Ceiling 2 FSL ( ) to the pagoda roof & wall 2 section by pulling the buttonettes from the ceiling piece into the corresponding eyelets on the middle section of the padoga roof & wall 2 section. Attach the remaining side of the pagoda roof & walls to form a square. Set aside. PHOTO 6 Attach a Pagoda Roof FSA ( ) triangle side to another side by inserting the four buttonettes along the left side into the four eyelets on the right side. Set aside. PHOTO 7 Attach the pagoda walls section to the pagoda roof & walls 1 section by pulling the buttonettes from the top of the walls into the corresponding eyelets on the roof & walls 1 section. PHOTO 8 Continue building the pagoda by attaching the previous pagoda section to the pagoda roof & wall 2 section by pulling the buttonettes from the pagoda roof & wall 1 section into the corresponding eyelets on the pagoda roof & wall 2 section. PHOTO 9 Attach the pagoda roof FSL piece to the top of the pagoda Photo 5 Photo 7 Photo 9 Photo 6 Photo 8 Photo 10 by pulling the buttonettes from the pagoda roof & wall 2 into the corresponding eyelets on the pagoda roof. PHOTO 10 Your Pagoda is complete.