32K x 8 Power Switched and Reprogrammable PROM

Size: px

Start display at page:

Download "32K x 8 Power Switched and Reprogrammable PROM"

Teresa Owen
5 years ago
Views:

1 1CY7C271A CY7C271A Features CMOS for optimum speed/power Windowed for reprogrammability High speed 25 ns (Commercial) Low power 275 mw (Commercial) Super low standby power Less than 85 mw when deselected EPROM technology 100%programmable Slim 300-mil package Direct replacement for bipolar PROMs Capable of withstanding >4001V static discharge Functional Description The CY7C271A is a high-performance 32,768-word by 8-bit CMOS PROM. When disabled (CE HIGH), the 7C271A Logic Block Diagram 32K x 8 Power Switched and Reprogrammable PROM automatically powers down into a low-power stand-by mode. The CY7C271A is packaged in the 300-mil slim package and is available in a cerdip package equipped with an erasure window to provide for reprogrammability. When exposed to UV light, the PROM is erased and can be reprogrammed. The memory cells utilize proven EPROM floating gate technology and byte-wide intelligent programming algorithms. The CY7C271A offers the advantages of lower power, superior performance, and programming yield. The EPROM cell requires only 12.5V for the super voltage, and low current requirements allow for gang programming. The EPROM cells allow each memory location to be tested 100% because each location is written into, erased, and repeatedly exercised prior to encapsulation. Each PROM is also tested for AC performance to guarantee that after customer programming, the product will meet DC and AC specification limits. Reading the 7C271A is accomplished by placing active LOW signals on CS 1 and CE, and an active HIGH on CS 2. The contents of the memory location addressed by the address lines (A 0 A 14 ) will become available on the output lines (O 0 O 7 ). Pin Configurations DIP/Flatpack A 14 A 13 A 12 A 11 A 10 A 9 A 8 A 7 A 6 A 5 A 4 X ADDRESS 256 x 1024 PROGRAMABLE ARRAY 8 x 1 OF 128 MULTIPLEXER O 7 O 6 O 5 O 4 O 3 A 9 A 8 A 7 A 6 A 5 A 4 A 3 A V CC A 10 A 11 A 12 A 13 A 14 CS 1 CS 2 A 1 A 0 O 0 O CE O 7 O 6 O 5 O 2 GND O 4 O 3 A 3 A 2 A 1 Y ADDRESS O 2 PLCC Top View A 0 CE CS 1 CS 2 POWER-DOWN O 1 O 0 A5 A6 A7 NC V CC A 8 PS A 5 25 E 4 A CLR A E S A CP A NC NC O 7 O O O 1 O 2 GND NC O 3 O 4 O 5 Cypress Semiconductor Corporation 3901 North First Street San Jose CA Document #: Rev. *B Revised December 28, 2002

2 Selection Guide 7C271A-25 7C271A-30 7C271A-35 7C271A-45 Unit Maximum Access Time ns Maximum Operating Current Com l ma Standby Current Com l ma Maximum Ratings [1] (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature C to +150 C Ambient Temperature with Power Applied C to +125 C Supply Voltage to Ground Potential V to +7.0V DC Voltage Applied to Outputs in High Z State V to +7.0V DC Input Voltage V to +7.0V DC Program Voltage V Static Discharge Voltage... >4001V (per MIL-STD-883, Method 3015) Latch-Up Current... >200 ma UV Exposure Wsec/cm 2 Operating Range Ambient Range Temperature V CC Commercial 0 C to +700 C 5V ±10% Electrical Characteristics Over the Operating Range [2, 3] 7C271A-25 7C271A-30 7C271A-35 7C271A-45 Parameter Description Test Conditions Min. Max. Min. Max. Min. Max. Unit V OH Output HIGH V CC = Min., I OH = 2.0 ma V Voltage V OL Output LOW Voltage V CC = Min., I OL = 8.0 ma V V IH Input HIGH Level Guaranteed Input Logical HIGH 2.0 V CC 2.0 V CC 2.0 V CC V Voltage for All Inputs V IL Input LOW Level Guaranteed Input Logical LOW V Voltage for All Inputs I IX Input Leakage GND < V IN < V CC µa Current I OZ Output Leakage Current GND < V OUT < V CC, Output Disable µa I OS I CC Output Short Circuit V CC = Max., V OUT = GND ma Current [4] Power Supply Current V CC =Max., I OUT = 0 ma, f = 10 MHz Com l ma I SB Stand-By Current V CC =Max., CE = V IH Com l ma Capacitance [3] Parameter Description Test Conditions Max. Unit C IN Input Capacitance T A = 25 C, f = 1 MHz, 10 pf C OUT Output Capacitance V CC = 5.0V 10 pf Notes: 1. The voltage on any input or I/O pin cannot exceed the power pin during power-up. 2. See the last page of this specification for Group A subgroup testing information. 3. See Introduction to CMOS PROMs in this Data Book for general information on testing. 4. For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed 30 seconds. Document #: Rev. *B Page 2 of 10

3 AC Test Loads and Waveforms 5V OUTPUT 30 pf R1 500Ω 658Ω MIL INCLUDING JIG AND SCOPE (a) NormalLoad R2 333Ω 403Ω MIL 5V OUTPUT 5 pf R1 500Ω 658Ω MIL INCLUDING JIG AND SCOPE (b) High-Z Load R2 333Ω 403Ω MIL 3.0V GND 5ns 10% ALL INPUT PULSES 90% 90% 10% 5ns Equivalent to: OUTPUT THÉ VENIN EQUIVALENT 200Ω 250Ω MIL 2.00V Commercial 1.90V MIL Switching Characteristics Over the Operating Range [2, 3] 7C271A-25 7C271A-30 7C271A-35 7C271A-45 Parameter Description Min. Max. Min. Max. Min. Max. Min. Max. Unit t AA Address to Output Valid ns t ACS CS 1 /CS 2 Active to Output Valid ns t ACE CE Active to Output Valid ns t HZCS CS 1 /CS 2 Inactive to High Z ns t HZCE CE Inactive to High Z ns t PU CE Active to Power-Up ns t PD CE Inactive to Power-Down ns t OH Output Data Hold ns Document #: Rev. *B Page 3 of 10

4 Switching Waveform I CC t PU t PD CE CS 2 ACTIVE INACTIVE ACTIVE CS 1 A 0 - A 14 ADDRA ADDRB t AA t AA O 0 - O 7 t ACE t HZCS t ACS t OH t HZCE DATA A DATAB DATAB Erasure Characteristics Wavelengths of light less than 4000 Angstroms begin to erase the CY7C271A in the windowed package. For this reason, an opaque label should be placed over the window if the PROM is exposed to sunlight or fluorescent lighting for extended periods of time. The recommended dose of ultraviolet light for erasure is a wavelength of 2537 Angstroms for a minimum dose (UV intensity multiplied by exposure time) of 25 Wsec/cm 2. For an ultraviolet lamp with a 12 mw/cm 2 power rating, the exposure time would be approximately 35 minutes. The CY7C271A needs to be within 1 inch of the lamp during erasure. Permanent damage may result if the PROM is exposed to high-intensity UV light for an extended period of time Wsec/cm 2 is the recommended maximum dosage. Programming Modes Programming support is available from Cypress as well as from a number of third-party software vendors. For detailed programming information, including a listing of software packages, please see the PROM Programming Information located at the end of this section. Programming algorithms can be obtained from any Cypress representative. Table 1. Programming Electrical Characteristics Parameter Description Min. Max. Unit V PP Programming Power Supply V I PP Programming Supply Current 50 ma V IHP Programming Input Voltage HIGH 3.0 V CC V V ILP Programming Input Voltage LOW V V CCP Programming V CC V Document #: Rev. *B Page 4 of 10

5 Table 2. Mode Selection Pin Function [5] Mode CS 1 /V PP CS 2 /PGM CE/VFY A 0 A 9 Data Read V IL V IH V IL A 0 A 9 O 7 O 0 Output Disable V IH V IH V IL A 0 A 9 High Z Output Disable V IL V IL V IL A 0 A 9 High Z Stand-by X X V IH A 0 A 9 High Z Program V PP V ILP V IHP A 0 A 9 D 7 D 0 Program Verify V PP V IHP V ILP A 0 A 9 O 7 O 0 Program Inhibit V PP V IHP V IHP X X X Signature (MFG) V ILP V ILP V ILP V ILP V HV [6] Signature (DEV) V ILP V ILP V ILP V IHP V HV [6] 20H Note: 5. X can be V IL or V IH. 6. V HV =12±0.5V 34H Programming Pinouts DIP Top View PLCC Top View A 7 A 6 A 5 A 4 A 3 A 2 A 1 A 0 D 0 D 1 D 2 GND V CC A 8 PS E V PP VFY PGM D 7 D 6 D 5 D 4 D 3 A5 A6 A7 NC V CC A8 PS A A A A A NC D D 1 D 2 GND NC D 3 D 4 D 5 E V PP VFY PGM NC D 7 D 6 Document #: Rev. *B Page 5 of 10

6 Typical DC and AC Characteristics NORMALIZED I CC NORMALIZED SUPPLY CURRENT vs. CYCLE PERIOD V CC =5.5V T A =25 C CLOCK PERIOD (ns) 250 NORMALIZED I CC NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE f= 10MHz 1.2 T 1.1 A = 25 C SUPPLY VOLTAGE (V) NORMALIZED I CC NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE V CC = 5.5V f= 10 MHz AMBIENT TEMPERATURE ( C) NORMALIZED ACCESS TIME NORMALIZED ACCESS TIME vs. SUPPLY VOLTAGE NORMALIZED ACCESS TIME vs. AMBIENT TEMPERATURE T A = 25 C NORMALIZED ACCESS TIME V CC = 4.5V OUTPUT SINK CURRENT (ma) OUTPUT SINK CURRENT vs. OUTPUT VOLTAGE V CC = 5.0V T A = 25 C SUPPLYVOLTAGE (V) AMBIENT TEMPERATURE ( C) OUTPUT VOLTAGE (V) OUTPUT SOURCE CURRENT OUTPUT SOURCE CURRENT vs. OUTPUT VOLTAGE OUTPUT VOLTAGE (V) 5.0 C271A-9 Document #: Rev. *B Page 6 of 10

7 Ordering Information Speed (ns) Ordering Code Package Name Package Type Operating Range 25 CY7C271A-25JC J65 32-Lead Plastic Leaded Chip Carrier Commercial 30 CY7C271A-30PC P21 28-Lead (300-Mil) Molded DIP Commercial 35 CY7C271A-35PC P21 28-Lead (300-Mil) Molded DIP Commercial CY7C271A-35WC W22 28-Lead (300-Mil) Windowed CerDIP 45 CY7C271A-45WC W22 28-Lead (300-Mil) Windowed CerDIP Commercial MILITARY SPECIFICATIONS Group A Subgroup Testing DC Characteristics Parameter Subgroups V OH 1, 2, 3 V OL 1, 2, 3 V IH 1, 2, 3 V IL 1, 2, 3 I IX 1, 2, 3 I OZ 1, 2, 3 I CC 1, 2, 3 I SB 1, 2, 3 Switching Characteristics Parameter Subgroups t AA 7, 8, 9, 10, 11 t ACS 7, 8, 9, 10, 11 t ACE 7, 8, 9, 10, 11 Document #: Rev. *B Page 7 of 10

8 Package Diagrams 28-Lead (300-Mil) Molded DIP P *B 32-Lead Plastic Leaded Chip Carrier J *B Document #: Rev. *B Page 8 of 10

9 Package Diagrams (continued) 28-Lead (300-Mil) Windowed CerDIP W22 MIL-STD-1835 D-15 Config. A ** All product and company names mentioned in this document may be the trademarks of their respective holders. Document #: Rev. *B Page 9 of 10 Cypress Semiconductor Corporation, The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.

10 Document History Page Document Title: CY7C271A 32K x 8 Power Switched and Reprogrammable PROM Document Number: REV. ECN NO. Issue Date Orig. of Change Description of Change ** /26/02 DSG Change from Spec number: to *A /13/02 GBI Update Ordering Information *B /26/02 RBI Add power up requirements to maximum ratings information Document #: Rev. *B Page 10 of 10

32K x 8 Power Switched and Reprogrammable PROM

32K x 8 Power Switched and Reprogrammable PROM 1 CY7C271 32K x Power Switched and Reprogrammable PROM Features CMOS for optimum speed/power Windowed for reprogrammability High speed 30 ns (Commercial) 3 ns (Military) Low power 660 mw (commercial) 71