2K x 8 Reprogrammable PROM

Size: px

Start display at page:

Download "2K x 8 Reprogrammable PROM"

Annis Eaton
6 years ago
Views:

2K x 8 Reprogrammable PROM Features Windowed for reprogrammability CMOS for optimum speed/power High speed 20 ns (Commercial) 35 ns (Military) Low power 660 mw (Commercial and Military) Low standby

1 2K x 8 Reprogrammable PROM Features Windowed for reprogrammability CMOS for optimum speed/power High speed 20 ns (Commercial) 35 ns (Military) Low power 660 mw (Commercial and Military) Low standby power 220 mw (Commercial and Military) EPROM technology 100% programmable Slim 300-mil or standard 600-mil packaging available 5V ±10% V CC, commercial and military TTL-compatible I/O Direct replacement for bipolar PROMs Capable of withstanding >2001V static discharge Functional Description The CY7C291A is a high-performance 2K-word by 8-bit CMOS PROM. It is packaged in a 300-mil ceramic package which may be equipped with an erasure window; when exposed to UV light the PROM is erased and can then be reprogrammed. The memory cells utilize proven EPROM floating-gate technology and byte-wide intelligent programming algorithms. The CY7C291A is a plug-in replacement for bipolar devices and offers the advantage of lower power, reprogrammability, superior performance and programming yield. The EPROM cell requires only 12.5V for the supervoltage and low current requirements allow for gang programming. The EPROM cells allow for each memory location to be tested 100%, as each location is written into, erased, and repeatedly exercised prior to encapsulation. Each PROM is also tested for AC performance to guarantee that after customer programming the product will meet DC and AC specification limits. A read is accomplished by placing an active LOW signal on CS 1, and active HIGH signals on CS 2 and CS 3. The contents of the memory location addressed by the address line (A 0 A 10 ) will become available on the output lines (O 0 O 7 ). Logic Block Diagram Pin Configurations A 0 A 1 A 2 A 3 A 4 A 5 A 6 A 7 A 8 A 9 A 10 ROW ADDRESS ADDRESS DECODER COLUMN ADDRESS PROGRAM- MABLE ARRAY POWER DOWN 7C293A MULTI- PLEXER O 7 O 6 O 5 O 4 O 3 O 2 O 1 O 0 A 7 A 6 A 5 A 4 A 3 A 2 A 1 A 0 DIP Top View C291A O O O GND V CC A 8 A 9 A 10 CS 1 CS 2 CS 3 O 7 O 6 O 5 O 4 O 3 LCC/PLCC (Opaque Only) Top View A5 A6 A7 NC V CC A8 A A 5 25 A 4 10 A 3 6 7C291A 24 CS 1 A CS 2 A CS 3 A NC NC O 7 O O O 1 O 2 GND NC O 3 O 4 O 5 Window available CS 1 CS 2 CS 3 Cypress Semiconductor Corporation 198 Champion Court San Jose, CA Document #: Rev. *B Revised August 17, 2006

2 Selection Guide 7C291A-20 7C291A-25 7C291A-35 7C291AL-35 7C291A-50 Maximum Access Time ns Maximum Operating Current Standard Commercial ma Military 90 ma L Commercial 60 ma Unit Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature C to +150 C Ambient Temperature with Power Applied C to +125 C Supply Voltage to Ground Potential V to +7.0V DC Voltage Applied to Outputs in High Z State V to +7.0V DC Input Voltage V to +7.0V DC Program Voltage V UV Exposure Wsec/cm 2 Static Discharge Voltage... >2001V (per MIL-STD-883, Method 3015) Latch-Up Current... >200 ma Operating Range Ambient Range Temperature V CC Commercial 0 C to + 70 C 5V ±10% Military [1] 55 C to C 5V ±10% Note 1. T A is the instant on case temperature. Document #: Rev. *B Page 2 of 13

3 Electrical Characteristics Over the Operating Range [2, 3] 7C291A-20 7C291A-25 Parameter Description Test Conditions Min. Max. Min. Max. Unit V OH Output HIGH Voltage V CC = Min., I OH = 4.0 ma V V OL Output LOW Voltage V CC = Min., I OL = 16.0 ma V V IH Input HIGH Voltage Guaranteed Input Logical 2.0 V CC 2.0 V CC V HIGH Voltage for All Inputs V IL Input LOW Voltage Guaranteed Input Logical V LOW Voltage for All Inputs I IX Input Load Current GND < V IN < V CC µa V CD Input Diode Clamp Voltage Note 3 I OZ Output Leakage Current GND < V OUT < V CC, Output Disabled I OS I CC I SB µa Output Short Circuit V CC = Max., V OUT = GND ma Current [4] V CC Operating Supply Current Standby Supply Current (7C293A Only) V CC = Max., I OUT = 0 ma Com l ma V CC = Max., Com l ma CS 1 = V IH V PP Programming Supply Voltage V I PP Programming Supply Current ma V IHP V ILP Input HIGH Programming Voltage Input LOW Programming Voltage V V Notes 2. See the last page of this specification for Group A subgroup testing information. 3. See the Introduction to CMOS PROMs section of the Cypress Data Book for general information on testing. 4. For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed 30 seconds. Document #: Rev. *B Page 3 of 13

4 Electrical Characteristics Over the Operating Range [2, 3] (continued) 7C291AL-35 7C291A-35 7C291A-50 Parameter Description Test Conditions Min. Max. Min. Max. Unit V OH Output HIGH Voltage V CC = Min., I OH = 4.0 ma V V OL Output LOW Voltage V CC = Min., I OL = 16.0 ma V V IH Input HIGH Voltage Guaranteed Input Logical HIGH Voltage for All Inputs V IL Input LOW Voltage Guaranteed Input Logical LOW Voltage for All Inputs V V I IX Input Load Current GND < V IN < V CC µa V CD Input Diode Clamp Voltage Note 3 I OZ Output Leakage Current GND < V OUT < V CC, Output Disabled µa I OS Output Short Circuit Current [4] V CC = Max., V OUT = GND ma I CC V CC Operating Supply Current V CC = Max., V IN = 2.0V I OUT = 0 ma I SB Standby Supply Current (7C293A Only) Commercial ma Military 90 V CC = Max., Commercial ma CS 1 = V IH Military 40 V PP Programming Supply Voltage V I PP Programming Supply Current ma V IHP Input HIGH Programming Voltage V V ILP Input LOW Programming Voltage V Capacitance [3] Parameter Description Test Conditions Max. Unit C IN Input Capacitance T A = 25 C, f = 1 MHz, 10 pf C OUT Output Capacitance V CC = 5.0V 10 pf Document #: Rev. *B Page 4 of 13

5 AC Test Loads and Waveforms [3] 5V OUTPUT 30pF INCLUDING JIG AND SCOPE R1250 Ω R2 167Ω 5V OUTPUT 5pF INCLUDING JIG AND SCOPE R1250 Ω R2 167Ω 3.0V GND <5ns ALL INPUT PULSES 90% 10% 90% 10% <5ns (a) Normal Load (b) HighZ Load Equivalent to: THÉ VENIN EQUIVALENT 100Ω OUTPUT 2.0V V CC SUPPLY CURRENT t PD t PU 50% 50% A 0 A 10 ADDRESS CS 2 CS 3 CS 1 t AA t HZCS t ACS O 0 O 7 Switching Characteristics Over the Operating Range [2, 3] 7C291A-20 7C291A-25 7C291A-35 7C291AL-35 7C291A-50 Parameter Description Min. Max. Min. Max. Min. Max. Min. Max. Unit t AA Address to Output Valid ns t HZCS1 Chip Select Inactive to High Z ns t ACS1 Chip Select Active to Output Valid ns t HZCS2 Chip Select Inactive to High Z ns t ACS2 Chip Select Active to Output Valid ns t PU Chip Select Active to Power-Up ns t PD Chip Select Inactive to Power-Down ns Document #: Rev. *B Page 5 of 13

6 Erasure Characteristics Wavelengths of light less than 4000 Angstroms begin to erase these PROMs. For this reason, an opaque label should be placed over the window if the PROM is exposed to sunlight or fluorescent lighting for extended periods of time. The recommended dose of ultraviolet light for erasure is a wavelength of 2537 Angstroms for a minimum dose (UV intensity x exposure time) of 25 Wsec/cm2. For an ultraviolet lamp with a 12 mw/cm 2 power rating, the exposure time would be approximately 35 minutes. Table 1. Mode Selection These PROMs need to be within 1 inch of the lamp during erasure. Permanent damage may result if the PROM is exposed to high-intensity UV light for an extended period of time Wsec/cm 2 is the recommended maximum dosage. Programming Information Programming support is available from Cypress as well as from a number of third-party software vendors. For detailed programming information, including a listing of software packages, please see the PROM Programming Information located at the end of this section. Programming algorithms can be obtained from any Cypress representative. Pin Function [5] Read or Output Disable A 10 A 0 CS 3 CS 2 CS 1 O 7 O 0 Mode Other A 10 A 0 PGM VFY V PP D 7 D 0 Read A 10 A 0 V IH V IH V IL O 7 O 0 Output Disable [6] A 10 A 0 X X V IH High Z Output Disable A 10 A 0 X V IL X High Z Output Disable A 10 A 0 V IL X X High Z Program A 10 A 0 V ILP V IHP V PP D 7 D 0 Program Verify A 10 A 0 V IHP V ILP V PP O 7 O 0 Program Inhibit A 10 A 0 V IHP V IHP V PP High Z Intelligent Program A 10 A 0 V ILP V IHP V PP D 7 D 0 Blank Check Zeros A 10 A 0 V IHP V ILP V PP Zeros Figure 1. Programming Pinouts DIP Top View LCC/PLCC (Opaque Only) Top View A 7 A 6 A 5 A 4 A 3 A 2 A 1 A 0 D 0 D 1 D 2 GND C291A V CC A 8 A 9 A 10 V PP VFY PGM D 7 D 6 D 5 D 4 D 3 A5 A6 A7 NC V CC A8 A A A 3 6 7C291A 24 A A A NC D D 1 D 2 GND NC D 3 D 4 D 5 A 10 V PP VFY PGM NC D 7 D 6 Notes 5. X = don t care but not to exceed V CC +5%. 6. The power-down mode for the CY7C293A is activated by deselecting CS 1. Document #: Rev. *B Page 6 of 13

7 Typical DC and AC Characteristics NORMALIZED I CC NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE T A =25 C f= f MAX SUPPLY VOLTAGE (V) NORMALIZED I CC NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE AMBIENT TEMPERATURE ( C) NORMALIZED ACCESS TIME NORMALIZED ACCESS TIME vs. SUPPLY VOLTAGE T A =25 C SUPPLY VOLTAGE (V) NORMALIZED ACCESS TIME NORMALIZED ACCESS TIME vs. TEMPERATURE AMBIENT TEMPERATURE ( C) OUTPUT SOURCE CURRENT (ma) OUTPUT SOURCE CURRENT vs. VOLTAGE OUTPUT VOLTAGE (V) 4.0 DELTA t AA (ns) TYPICAL ACCESS TIME CHANGE vs. OUTPUT LOADING V CC =4.5V T A =25 C CAPACITANCE (pf) OUTPUT SINK CURRENT (ma) OUTPUT SINK CURRENT vs. OUTPUT VOLTAGE 75 V CC =5.0V 50 T A =25 C OUTPUT VOLTAGE (V) 4.0 NORMALIZED I CC I CC vs. CYCLEPERIOD V CC =5.5V T A =25 C CYCLE PERIOD (ns) Document #: Rev. *B Page 7 of 13

8 Ordering Information Speed I CC Package (ns) (ma) Ordering Code Name Package Type Operating Range CY7C291A-20PC P13 24-Lead (300-Mil) Molded DIP Commercial CY7C291A-25JC J64 28-Lead Plastic Leaded Chip Carrier Commercial CY7C291A-25PC P13 24-Lead (300-Mil) Molded DIP CY7C291AL-35JC J64 28-Lead Plastic Leaded Chip Carrier Commercial CY7C291AL-35PC P13 24-Lead (300-Mil) Molded DIP CY7C291AL-35WC W14 24-Lead (300-Mil) Windowed CerDIP 90 CY7C291A-35JC J64 28-Lead Plastic Leaded Chip Carrier Commercial CY7C291A-35PC P13 24-Lead (300-Mil) Molded DIP CY7C291A-35WC W14 24-Lead (300-Mil) Windowed CerDIP 120 CY7C291A-35DMB D14 24-Lead (300-Mil) CerDIP Military CY7C291A-50PC P13 24-Lead (300-Mil) Molded DIP Commercial CY7C291A-50WMB W14 24-Lead (300-Mil) Windowed CerDIP Military MILITARY SPECIFICATIONS Group A Subgroup Testing DC Characteristics Parameter Subgroups V OH 1, 2, 3 V OL 1, 2, 3 V IH 1, 2, 3 V IL 1, 2, 3 I IX 1, 2, 3 I OZ 1, 2, 3 I CC 1, 2, 3 I SB 1, 2, 3 SMD Cross Reference SMD Number Suffix Cypress Number LX CY7C291-50WMB LX CY7C291-35WMB X CY7C291A-35LMB X CY7C291A-35LMB LX CY7C291A-25DMB X CY7C291A-25LMB Switching Characteristics Parameter Subgroups t AA 7, 8, 9, 10, 11 t ACS1 7, 8, 9, 10, 11 Document #: Rev. *B Page 8 of 13

9 Package Diagrams Figure Lead (300-Mil) CerDIP D14 MIL-STD-1835 D- 9 Config.A Figure Lead (300-Mil) PDIP P ** *B Document #: Rev. *B Page 9 of 13

10 Package Diagrams (continued) Figure Pin Windowed Leadless Chip Carrier Q64 MIL STD 1835 C ** Document #: Rev. *B Page 10 of 13

11 Package Diagrams (continued) Figure Lead (300 Mil) SOIC - S13 NOTE : PIN 1 ID 1. JEDEC STD REF MO BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH,BUT 12 1 DOES INCLUDE MOLD MISMATCH AND ARE MEASURED AT THE MOLD PARTING LINE. MOLD PROTRUSION/END FLASH SHALL NOT EXCEED in (0.254 mm) PER SIDE 0.291[7.391] 0.300[7.620] 0.394[10.007] 0.419[10.642] 3. DIMENSIONS IN INCHES 4. PACKAGE WEIGHT 0.65gms * MIN. MAX [0.660] 0.032[0.812] PART # S24.3 STANDARD PKG. SZ24.3 LEAD FREE PKG. SEATING PLANE 0.597[15.163] 0.615[15.621] 0.092[2.336] 0.105[2.667] 0.050[1.270] TYP [0.330] 0.019[0.482] 0.004[0.101] [0.299] * 0.004[0.101] 0.015[0.381] 0.050[1.270] [0.231] [0.317] *C * Document #: Rev. *B Page 11 of 13

12 Package Diagrams (continued) Figure Lead (300-Mil) Windowed CerDIP W14 MIL-STD-1835 D-9 Config. A ** All product and company names mentioned in this document may be the trademarks of their respective holders. Document #: Rev. *B Page 12 of 13 Cypress Semiconductor Corporation, The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

13 Document History Page Document Title: CY7C291A 2K x 8 Reprogrammable PROM Document Number: REV. ECN NO. Issue Date Orig. of Change Description of Change ** /18/02 DSG Changed from Spec number: to *A /11/02 GBI Updated ordering information *B See ECN PCI Updated ordering information Document #: Rev. *B Page 13 of 13

2K x 8 Reprogrammable PROM

2K x 8 Reprogrammable PROM 1CY 7C29 2A CY7C291A Features Windowed for reprogrammability CMOS for optimum speed/power High speed 20 ns (commercial) 25 ns (military) Low power 660 mw (commercial and military) Low standby power 220