NEC's 3.0 GHz DIVIDE BY 64/128/256 PRESCALER VOUT PACKAGE OUTLINE

Transcription

1 FEATURES NE's 3. GHz IVIE BY 64/8/56 PRESALER HIGH FREUENY OPERATION TO 3 GHz SELETABLE IVIE RATIO: 64, 8, 56 LOW URRENT ONSUMPTION: 9 ma at 5 V SMALL PAKAGE: 8 pin SSOP AVAILABLE IN TAPE AN REEL ESRIPTION NE's UPB56GV and UPB57GV are Silicon MMI digital prescalers manufactured with the NESAT IV silicon bipolar process. They feature high frequency response to 3 GHz, selectable divide-by-64, 8, or 56 modes, and operate on a 5 volt supply while drawing only 9 ma. The devices are housed in a small 8 pin SSOP package that contributes to system miniaturization. These devices are designed for use in a PLL synthesizer for BS and ATV settop and WLAN applications. PART NUMBER PAKAGE OUTLINE TEST IRUIT ELETRIAL HARATERISTIS (TA = -4 to +85, V = 4.5 to 5.5 V, Zs = 5Ω) UPB56GV,UPB57GV S8 SYMBOLS PARAMETERS AN ONITIONS UNITS MIN TYP MAX I ircuit urrent ma fin(u) Upper Limit Operating Frequency, PIN = -5 to +6 dbm GHz 3. fin(l) Lower Limit Operating Frequency, PIN = - to +6 dbm GHz.5 fin(l) Lower Limit Operating Frequency, PIN = -5 to +6 dbm GHz. PIN Input Power, fin =. to 3. GHz dbm PIN Input Power, fin =.5 to. GHz dbm - +6 VOUT Output Voltage, L =.8 pf VP-P..6 VIN(H) ivision Ratio ontrol Input High V V VIN(L) ivision Ratio ontrol Input Low V OPEN or GN fin VOUT 3 4 IN V SW OUT = pf UPB57GV UPB56GV UPB57GV IN N V SW GN OPEN, pf alifornia Eastern Laboratories

2 UPB56GV, UPB57GV ABSOLUTE MAXIMUM RATINGS (TA = 5 ) SYMBOLS PARAMETERS UNITS RATINGS V Supply Voltage V -.5 to 6. VIN Input Voltage V -.5 to Vcc +.5 PIN Input Power dbm + P Power issipation mw 5 TOP Operating Temperature -45 to +85 TSTG Storage Temperature -55 to +5 Notes:. Operation in excess of any one of these parameters may result in permanent damage.. Mounted on a double-sided copper clad 5x5x.6 mm epoxy glass PWB (TA = +85 ). PIN ESRIPTIONS Pin No. Pin Applied Pin escription Name Voltage Voltage UPB56GV UPB57GV (V) (V) IN.9 Signal input pin. This pin should be coupled to the source with a capacitor (eg pf). 3 8 IN.9 Signal input bypass pin. This pin must be equipped with a bypass capacitor (eg pf) to ground. 4 5 GN Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance. 3 SW H/L ivided ratio input pin. The ratio can be controlled by the following input data to these pins. 6 6 SW REOMMENE OPERATING ONITIONS These pins should be equipped with a bypass capacitor (e.g. pf) to ground. 8 V 4.5 to 5.5 Power supply pin. This pin must be equipped with bypass capacitor (eg pf) to ground. 7 4 OUT.6 to 4.7 ivided frequency output pin. This pin is designed as an emitter follower output. This pin can be connected to MOS input due to. Vp-p MIN output. 5 7 N No connection. This pin must be opened. SW SYMBOL PARAMETER UNITS MIN TYP MAX V Supply Voltage V TOP Operating Temperature H SW H 64 8 L 8 56 L

3 UPB56GV, UPB57GV TYPIAL PERFORMANE URVES ( unless otherwise noted) Input Power, PIN (dbm) ircuit urrent, I (ma) URRENT vs. VOLTAGE and TEMPERATURE No Signals TA = -4 V = 4.5 to 5.5 V TA = TA = -4 Supply Voltage, V (V) INPUT POWER vs. INPUT FREUENY and TEMPERATURE TA = +85 TA = -4 PIN = - dbm 4 5 Guaranteed Operating Window TA = +85 TA = -4 V = 4.5 V V = 5.5 V 6 Input Power, PIN (dbm) INPUT POWER vs. PIN = - dbm. TA = +85 PIN = - dbm V = 4.5 to 5.5 V Guaranteed Operating Window V = 4.5 to 5.5 V V = 5.5 V V = 4.5 V V = 4.5 V V = 5.5 V.4.4

4 UPB56GV, UPB57GV TYPIAL PERFORMANE URVES ( unless otherwise noted) Input Power, PIN (dbm) INPUT POWER vs. V = 4.5 to 5.5 V PIN = - dbm TA = +85 PIN = - dbm Guaranteed Operating Window V = 4.5 to 5.5 V V = 5.5 V V = 4.5 V V = 5.5 V V = 4.5 V Input Power, PIN (dbm) Input Power, PIN (dbm) + + INPUT POWER vs. INPUT FREUENY and TEMPERATURE V = 4.5 to 5.5 V TA = -4 TA = +85 TA = -4 PIN = - dbm V = 4.5 to 5.5 V Guaranteed Operating Window TA = +85 TA = -4 V = 5.5 V V = 4.5 V INPUT POWER vs. Guaranteed Operating Window V = 4.5 to 5.5 V. -6

5 UPB56GV, UPB57GV TYPIAL PERFORMANE URVES ( unless otherwise noted) Input Power, PIN (dbm) INPUT POWER vs. V = 4.5 to 5.5 V TA = -4 TA = +85 TA = -4 PIN = - dbm TA = -4 Guaranteed Operating Window TA = +85 V = 5.5 V V = 4.5 V PIN = - dbm TA = +85 PIN = - dbm V = 5.5 V V = 4.5 V V = 5.5 V V = 4.5 V

6 UPB56GV, UPB57GV TYPIAL SATTERING PARAMETERS (TA = 5 ) UPB56GV S Z REF. Units 3. munits/ Ω Ω MARKER 3. GHZ UPB56GV S vs. INPUT FREUENY 4 S Z REF. Units. munits/ 7. Ω Ω MARKER 45. MHZ START.5 GHz STOP 3. GHz S vs. OUTPUT FREUENY ivide by 64 mode, START.45 GHz STOP. GHz 3 :.5 GHz :. GHz 3 :. GHz 4 : 3. GHz : 45 MHz : MHz FREUENY S GHz MAG ANG FREUENY S MHz MAG ANG

7 UPB56GV, UPB57GV TYPIAL SATTERING PARAMETERS (TA = 5 ) UPB56GV S Z REF. Units. munits/ 9.34 Ω 3.9 Ω MARKER 45. MHZ UPB56GV S Z REF. Units. munits/ 99.5 Ω Ω S vs. OUTPUT FREUENY ivide by 8 mode, MARKER 45. GHZ START.45 GHz STOP. GHz S vs. OUTPUT FREUENY ivide by 56 mode, : 45 MHz : MHz : 45 MHz : MHz FREUENY S MHz MAG ANG FREUENY S MHz MAG ANG START.45 GHz STOP. GHz

8 UPB56GV, UPB57GV TYPIAL SATTERING PARAMETERS (TA = 5 ) UPB57GV S REF 4 Z. Units. munits/ 38. Ω.977 Ω MARKER 4 3. GHZ UPB57GV S Z REF. Units. munits/ 85.3 Ω Ω MARKER 45. GHZ S vs. INPUT FREUENY 4 START.5 GHz STOP 3. GHz S vs. OUTPUT FREUENY ivide by 64 mode, 3 :.5 GHz :. GHz 3 :. GHz 4 : 3. GHz : 45 MHz : MHz FREUENY S GHz MAG ANG FREUENY S MHz MAG ANG START.45 GHz STOP. GHz

9 UPB56GV, UPB57GV TYPIAL SATTERING PARAMETERS (TA = 5 ) UPB57GV S REF Z. Units. munits/ 85. Ω Ω MARKER 45. GHZ UPB57GV S Z REF. Units 4. munits/ Ω 7.8 Ω S vs. OUTPUT FREUENY ivide by 8 mode, MARKER 45. GHZ START.45 GHz STOP. GHz S vs. OUTPUT FREUENY ivide by 56 mode, : 45 MHz : MHz : 45 MHz : MHz FREUENY S MHz MAG ANG FREUENY S MHz MAG ANG START.45 GHz STOP. GHz

10 UPB56GV, UPB57GV SYSTEM APPLIATION EXAMPLE RF unit block of Analog BS tuners stif input from BS converter To 5 MHz To 8 MHz OS To 65 MHz BPF MIX BPF SAW AG amp. FM demo. LPF loop filter High ivision prescaler UPB56GV or UPB57GV RF unit block of Analog ATV converter OS To MHz upconverter LPF BPF loop filter downconverter High ivision prescaler UPB56GV or UPB57GV To 3 MHz MOS PLL synthesizer MOS PLL synthesizer

11 UPB56GV, UPB57GV INTERNAL BLOK IAGRAM OUTLINE IMENSIONS (Units in mm) IN IN LK LK LK 3 LK LK LK LK SW PIN ONNETIONS LK LK SW Pin No. UPB56GV UPB57GV SW IN IN Vcc 3 IN SW 4 GN OUT 5 OPEN GN 6 SW SW 7 OUT OPEN 8 Vcc IN AMP OUT.8 MAX PAKAGE OUTLINE S8.5±.. ± N MAX ORERING INFORMATION PART NUMBER UANTITY MARKING UPB56GV-E /Reel 56 UPB57GV-E-A /Reel 57 Note:. Embossed tape 8 mm wide. Pin is in the tape pull-out direction MAX etail of Lead End.5 ± ±. 3.±. Life Support Applications These NE products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of EL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify EL for all damages resulting from such improper use or sale..87±. 7//4 A Business Partner of NE ompound Semiconductor evices, Ltd.

12 Subject: ompliance with EU irectives 459 Patrick Henry rive Santa lara, A Telephone: (48) 99-5 Facsimile: (48) EL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) irective /95/E Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU irective 3//E Restriction on Penta and Octa BE. EL Pb-free products have the same base part number with a suffix added. The suffix A indicates that the device is Pb-free. The AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on EL s understanding of the EU irectives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) oncentration Limit per RoHS (values are not yet fixed) < PPM oncentration contained in EL devices -A -AZ Not etected (*) Mercury < PPM Not etected admium < PPM Not etected Hexavalent hromium < PPM Not etected PBB < PPM Not etected PBE < PPM Not etected If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and isclaimer: Information provided by EL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. EL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. EL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. EL and EL suppliers consider certain information to be proprietary, and thus AS numbers and other limited information may not be available for release. In no event shall EL s liability arising out of such information exceed the total purchase price of the EL part(s) at issue sold by EL to customer on an annual basis. See EL Terms and onditions for additional clarification of warranties and liability.