FAMILY PACKAGE TABLE PACKAGE TYPES UNIVERSAL SHUTDOWN CHANNELS MSOP PDIP SOIC TSSOP

Transcription

1 Wide Bandwidth... MHz High Output Drive I OH ma at V DD.5 V I OL ma at.5 V High Slew Rate SR V/µs SR... 9 V/µs Wide Supply Range V to 6 V Supply Current....9 ma/channel Ultralow Power Shutdown Mode I DD µa/channel Low Input Noise Voltage nv Hz Input Offset Voltage...6 µv Ultra-Small Packages 8 or Pin MSOP (TLC8//2/3) description SLOS254E JUNE 999 REVISED APRIL 26 Operational Amplifier The first members of TI s new BiMOS general-purpose operational amplifier family are the TLC8x. The BiMOS family concept is simple: provide an upgrade path for BiFET users who are moving away from dual-supply to single-supply systems and demand higher ac and dc performance. With performance rated from 4.5 V to 6 V across commercial ( C to 7 C) and an extended industrial temperature range ( 4 C to 25 C), BiMOS suits a wide range of audio, automotive, industrial, and instrumentation applications. Familiar features like offset nulling pins, and new features like MSOP PowerPAD packages and shutdown modes, enable higher levels of performance in a variety of applications. Developed in TI s patented LBC3 BiCMOS process, the new BiMOS amplifiers combine a very high input impedance, low-noise CMOS front end with a high-drive bipolar output stage, thus providing the optimum performance features of both. AC performance improvements over the TL8x BiFET predecessors include a bandwidth of MHz (an increase of 3%) and voltage noise of 8.5 nv/ Hz (an improvement of 6%). DC improvements include an ensured V ICR that includes ground, a factor of 4 reduction in input offset voltage down to.5 mv (maximum) in the standard grade, and a power supply rejection improvement of greater than 4 db to 3 db. Added to this list of impressive features is the ability to drive ±5-mA loads comfortably from an ultrasmall-footprint MSOP PowerPAD package, which positions the TLC8x as the ideal high-performance general-purpose operational amplifier family. FAMILY PACKAGE TABLE DEVICE NO. OF PACKAGE TYPES UNIVERSAL SHUTDOWN CHANNELS MSOP PDIP SOIC TSSOP EVM BOARD TLC Yes TLC TLC Refer to the EVM Selection Guide TLC Yes (Lit# SLOU6) TLC TLC Yes + Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. Copyright 2 26 Texas Instruments Incorporated

2 SLOS254E JUNE 999 REVISED APRIL 26 TLC8 and TLC8 AVAILABLE OPTIONS PACKAGED DEVICES TA SMALL OUTLINE SMALL OUTLINE (D) (DGN) C to 7 C 4 C to 25 C TLC8CD TLC8CD TLC8ID TLC8ID TLC8AID TLC8AID TLC8CDGN TLC8CDGN TLC8IDGN TLC8IDGN SYMBOL xxtiacw xxtiacy xxtiacx xxtiacz PLASTIC DIP (P) TLC8CP TLC8CP TLC8IP TLC8IP TLC8AIP TLC8AIP This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLC8CDR). TA C to 7 C 4 C to 25 C TLC82 and TLC83 AVAILABLE OPTIONS PACKAGED DEVICES SMALL MSOP OUTLINE (D) (DGN) SYMBOL (DGQ) SYMBOL TLC82CD TLC83CD TLC82ID TLC83ID TLC82AID TLC83AID TLC82CDGN TLC82IDGN xxtiadz xxtiaea TLC83CDGQ TLC83IDGQ xxtiaeb xxtiaec PLASTIC DIP (N) TLC83CN TLC83IN TLC83AIN This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLC82CDR). xx represents the device date code. PLASTIC DIP (P) TLC82CP TLC82IP TLC82AIP TA C to 7 C 4 C to 25 C TLC84 and TLC85 AVAILABLE OPTIONS PACKAGED DEVICES SMALL OUTLINE (D) TLC84CD TLC85CD TLC84ID TLC85ID TLC84AID TLC85AID PLASTIC DIP (N) TLC84CN TLC85CN TLC84IN TLC85IN TLC84AIN TLC85AIN TSSOP (PWP) TLC84CPWP TLC85CPWP TLC84IPWP TLC85IPWP TLC84AIPWP TLC85AIPWP This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLC84CDR). For the most current package and ordering information, see the Package Option Addendum at the end of this data sheet, or see the TI web site at 2

3 SLOS254E JUNE 999 REVISED APRIL 26 TLC8x PACKAGE PINOUTS TLC8 D, DGN, OR P PACKAGE (TOP VIEW) TLC8 D, DGN, OR P PACKAGE (TOP VIEW) TLC82 D, DGN, OR P PACKAGE (TOP VIEW) NULL IN IN+ GND SHDN V DD OUT NULL NULL IN IN+ GND NC V DD OUT NULL OUT IN IN+ GND V DD 2OUT 2IN 2IN+ TLC83 DGQ PACKAGE (TOP VIEW) TLC83 D OR N PACKAGE (TOP VIEW) TLC84 D OR N PACKAGE (TOP VIEW) OUT IN IN+ GND SHDN V DD 2OUT 2IN 2IN+ 2SHDN OUT IN IN+ GND NC SHDN NC V DD 2OUT 2IN 2IN+ NC 2SHDN NC OUT IN IN+ V DD 2IN+ 2IN 2OUT OUT 4IN 4IN+ GND 3IN+ 3IN 3OUT TLC84 PWP PACKAGE (TOP VIEW) TLC85 D OR N PACKAGE (TOP VIEW) TLC85 PWP PACKAGE (TOP VIEW) OUT IN IN+ VDD 2IN+ 2IN 2OUT NC NC NC OUT 4IN 4IN+ GND 3IN+ 3IN 3OUT NC NC NC OUT IN IN+ V DD 2IN+ 2IN 2OUT /2SHDN OUT 4IN 4IN+ GND 3IN+ 3IN 3OUT 3/4SHDN OUT IN IN+ VDD 2IN+ 2IN 2OUT /2SHDN NC NC OUT 4IN 4IN+ GND 3IN+ 3IN 3OUT 3/4SHDN NC NC NC No internal connection TYPICAL PIN INDICATORS Pin Printed or Molded Dot Pin Stripe Pin Bevel Edges Pin Molded U Shape 3

4 SLOS254E JUNE 999 REVISED APRIL 26 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, V DD (see Note ) V Differential input voltage range, V ID ±V DD Continuous total power dissipation See Dissipation Rating Table Operating free-air temperature range, T A : C suffix C to 7 C I suffix C to 25 C Maximum junction temperature, T J C Storage temperature range, T stg C to 5 C Lead temperature,6 mm (/6 inch) from case for seconds C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE : All voltage values, except differential voltages, are with respect to GND. PACKAGE recommended operating conditions Supply voltage, VDD DISSIPATION RATING TABLE θjc ( C/W) θja ( C/W) TA 25 C POWER RATING D (8) mw D (4) mw D (6) mw DGN (8) W DGQ () W N (4, 6) mw P (8) mw PWP (2) W MIN MAX UNIT Single supply V Split supply ±2.25 ±8 Common-mode input voltage, VICR GND VDD 2 V Shutdown on/off voltage level Operating free-air temperature, TA Relative to the voltage on the GND terminal of the device. VIH 2 VIL.8 C-suffix 7 I-suffix 4 25 V C 4

5 SLOS254E JUNE 999 REVISED APRIL 26 electrical characteristics at specified free-air temperature, V DD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT TLC8//2/3, 25 C 39 9 TLC84/5 Full range 3 VIO Input offset voltage VDD = 5 V, µvv VIC = 2.5 V, TLC8//2/3A, 25 C 39 4 VO O = 2.5 V, TLC84/5A Full range 2 RS = 5 Ω Temperature coefficient of input αvio.2 µv/ C C offset voltage IIO IIB Input offset current Input bias current VICR Common-mode input voltage RS = 5 Ω VOH High-level output voltage VIC = 2.5 V VOL Low-level output voltage VIC = 2.5 V IOS Short-circuit output current 25 C.9 5 TLC8XC pa VDD = 5 V, Full range TLC8XI 7 VIC = 2.5 V, VO = 2.5 V, 25 C 3 5 RS = 5 Ω TLC8XC pa Full range TLC8XI 7 IOH = ma IOH = 2 ma IOH = 35 ma IOH = 5 ma IOL = ma IOL = 2 ma IOL = 35 ma IOL = 5 ma 25 C Full range to 3. to 3. to 3.5 to C Full range C Full range 3.5 V 25 C V Full range C C to 85 C 3 25 C.8.25 Full range C Full range C V Full range.7 25 C C to 85 C Sourcing 25 C Sinking 25 C VOH =.5 V from positive rail 25 C 57 IO Output current VOL =.5 V from negative rail 25 C 55 Full range is C to 7 C for C suffix and 4 C to 25 C for I suffix. If not specified, full range is 4 C to 25 C..7 ma ma 5

6 SLOS254E JUNE 999 REVISED APRIL 26 electrical characteristics at specified free-air temperature, V DD = 5 V (unless otherwise noted) (continued) AVD PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT Large-signal differential voltage amplification VO(PP) = 3 V, RL = kω 25 C 2 Full range ri(d) Differential input resistance 25 C GΩ CIC Common-mode input capacitance f = khz 25 C 22.9 pf zo Closed-loop output impedance f = khz, AV = 25 C.25 Ω CMRR Common-mode rejection ratio VIC = to 3 V, RS = 5 Ω ksvr 25 C 8 Full range 8 Supply voltage rejection ratio VDD = 4.5 V to 6 V, VIC = VDD /2, 25 C 8 ( VDD / VIO) No load Full range 8 IDD Supply current (per channel) VO = 2.5 V, No load 25 C Full range 3.5 Supply current in shutdown IDD(SHDN) mode (per channel) SHDN.8 V (TLC8, TLC83, TLC85) 25 C Full range Full range is C to 7 C for C suffix and 4 C to 25 C for I suffix. If not specified, full range is 4 C to 25 C. db db db ma µaa 6

7 SLOS254E JUNE 999 REVISED APRIL 26 operating characteristics at specified free-air temperature, V DD = 5 V (unless otherwise noted) SR+ SR Vn PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT Positive slew rate at unity gain Negative slew rate at unity gain Equivalent input noise voltage VO(PP) =.8 V, CL = 5 pf, 25 C 6 RL = kω Full range 9.5 VO(PP) =.8 V, CL = 5 pf, 25 C RL = kω Full range f = Hz 25 C 2 f = khz 25 C 8.5 V/µs V/µs nv/ Hz In Equivalent input noise current f = khz 25 C.6 fa / Hz AV =.2% VO(PP) = 3 V, THD + N Total harmonic distortion plus noise RL = kω and 25 Ω, AV = 25 C.2% f = khz AV =.85% t(on) Amplifier turnon time 25 C.5 µs t(off) Amplifier turnoff time RL = kω 25 C.3 µs ts φm Gain-bandwidth product f = khz, RL = kω 25 C MHz Settling time Phase margin Gain margin V(STEP)PP = V, AV =, CL = pf, RL = kω V(STEP)PP = V, AV =, CL = 47 pf, RL = kω RL = kω, RL = kω, RL = kω, RL = kω,.%.8.%.% 25 C.39.8.%.39 CL = 5 pf CL = pf CL = 5 pf CL = pf Full range is C to 7 C for C suffix and 4 C to 25 C for I suffix. If not specified, full range is 4 C to 25 C. Disable time and enable time are defined as the interval between application of the logic signal to SHDN and the point at which the supply current has reached half its final value. 25 C 25 C µss db 7

8 SLOS254E JUNE 999 REVISED APRIL 26 electrical characteristics at specified free-air temperature, V DD = 2 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT TLC84/2/3, 25 C 39 9 TLC84/5 Full range 3 VIO Input offset voltage VDD = 2 V µvv VIC = 6 V, TLC84/2/3A, 25 C 39 4 VO O = 6 V, TLC84/5A Full range 2 RS = 5 Ω Temperature coefficient of input αvio.2 µv/ C C offset voltage IIO IIB Input offset current Input bias current VICR Common-mode input voltage RS = 5 Ω VOH High-level output voltage VIC = 6 V VOL Low-level output voltage VIC = 6 V IOS Short-circuit output current 25 C.5 5 TLC8xC pa VDD = 2 V Full range TLC8xI 7 VIC = 6 V, VO = 6 V, 25 C 2 5 RS = 5 Ω TLC8xC pa Full range TLC8xI 7 IOH = ma IOH = 2 ma IOH = 35 ma IOH = 5 ma IOL = ma IOL = 2 ma IOL = 35 ma IOL = 5 ma 25 C Full range to. to. to.5 to.5 25 C..2 Full range 25 C.8 Full range.7 V 25 C.6.7 V Full range.3 25 C C to 85 C.2 25 C.7.25 Full range C Full range.5 25 C.4.52 V Full range.6 25 C C to 85 C Sourcing 25 C 5 Sinking 25 C 5 VOH =.5 V from positive rail 25 C 57 IO Output current VOL =.5 V from negative rail 25 C 55 Full range is C to 7 C for C suffix and 4 C to 25 C for I suffix. If not specified, full range is 4 C to 25 C..65 ma ma 8

9 SLOS254E JUNE 999 REVISED APRIL 26 electrical characteristics at specified free-air temperature, V DD = 2 V (unless otherwise noted) (continued) AVD PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT Large-signal differential voltage amplification VO(PP) = 8 V, RL = kω 25 C 2 4 Full range 2 ri(d) Differential input resistance 25 C GΩ CIC Common-mode input capacitance f = khz 25 C 2.6 pf zo Closed-loop output impedance f = khz, AV = 25 C.25 Ω CMRR Common-mode rejection ratio VIC = to V, RS = 5 Ω ksvr 25 C 8 Full range 8 Supply voltage rejection ratio VDD = 4.5 V to 6 V, VIC = VDD /2, 25 C 8 ( VDD / VIO) No load Full range 8 IDD Supply current (per channel) VO = 7.5 V, No load 25 C Full range 3.5 Supply current in shutdown IDD(SHDN) mode (TLC8, TLC83, SHDN.8 V TLC85) (per channel) 25 C Full range Full range is C to 7 C for C suffix and 4 C to 25 C for I suffix. If not specified, full range is 4 C to 25 C. db db db ma µaa 9

10 SLOS254E JUNE 999 REVISED APRIL 26 operating characteristics at specified free-air temperature, V DD = 2 V (unless otherwise noted) SR+ SR Vn PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT Positive slew rate at unity gain Negative slew rate at unity gain Equivalent input noise voltage VO(PP) = 2 V, CL = 5 pf, 25 C 6 RL = kω Full range 9.5 VO(PP) = 2 V, CL = 5 pf, 25 C RL = kω Full range f = Hz 25 C 4 f = khz 25 C 8.5 V/µs V/µs nv/ Hz In Equivalent input noise current f = khz 25 C.6 fa / Hz AV =.2% VO(PP) = 8 V, THD + N Total harmonic distortion plus noise RL = kω and 25 Ω, AV = 25 C.5% f = khz AV =.22% t(on) Amplifier turnon time 25 C.47 µs t(off) Amplifier turnoff time RL = kω 25 C 2.5 µs ts φm Gain-bandwidth product f = khz, RL = kω 25 C MHz Settling time Phase margin Gain margin V(STEP)PP = V, AV =, CL = pf, RL = kω V(STEP)PP = V, AV =, CL = 47 pf, RL = kω RL = kω, RL = kω, RL = kω, RL = kω,.%.7.%.% 25 C.22.7.%.29 CL = 5 pf CL = pf CL = 5 pf CL = pf Full range is C to 7 C for C suffix and 4 C to 25 C for I suffix. If not specified, full range is 4 C to 25 C. Disable time and enable time are defined as the interval between application of the logic signal to SHDN and the point at which the supply current has reached half its final value. 25 C 25 C µss db

11 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Common-mode input voltage, 2 IIO Input offset current Free-air temperature 3, 4 IIB Input bias current Free-air temperature 3, 4 VOH High-level output voltage High-level output current 5, 7 VOL Low-level output voltage Low-level output current 6, 8 Zo Output impedance Frequency 9 IDD Supply current Supply voltage PSRR Power supply rejection ratio Frequency CMRR Common-mode rejection ratio Frequency 2 Vn Equivalent input noise voltage Frequency 3 VO(PP) Peak-to-peak output voltage Frequency 4, 5 Crosstalk Frequency 6 Differential voltage gain Frequency 7, 8 Phase Frequency 7, 8 φm Phase margin Load capacitance 9, 2 SR THD + N Gain margin Load capacitance 2, 22 Gain-bandwidth product Supply voltage 23 Slew rate Total harmonic distortion plus noise Supply voltage Free-air temperature 24 25, 26 Frequency 27, 28 Peak-to-peak output voltage 29, 3 Large-signal follower pulse response 3, 32 Small-signal follower pulse response 33 Large-signal inverting pulse response 34, 35 Small-signal inverting pulse response 36 Shutdown forward isolation Frequency 37, 38 Shutdown reverse isolation Frequency 39, 4 Shutdown supply current Supply voltage 4 Free-air temperature 42 Shutdown pulse 43, 44

12 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS V IO Input Offset Voltage µ V INPUT OFFSET VOLTAGE COMMON-MODE INPUT VOLTAGE VDD = 5 V 8 TA = 25 C VICR Common-Mode Input Voltage V Figure V IO Input Offset Voltage µ V INPUT OFFSET VOLTAGE COMMON-MODE INPUT VOLTAGE 5 3 VDD = 2 V TA = 25 C VICR Common-Mode Input Voltage V Figure 2 / I IO Input Bias and Input Offset Current pa I IB INPUT BIAS CURRENT AND INPUT OFFSET CURRENT FREE-AIR TEMPERATURE VDD = 5 V IIB TA Free Air Temperature C Figure 3 IIO / I IO Input Bias and Input Offset Current pa I IB INPUT BIAS CURRENT AND INPUT OFFSET CURRENT FREE-AIR TEMPERATURE VDD = 2 V TA Free-Air Temperature C Figure 4 IIO IIB V OH High-Level Output Voltage V HIGH-LEVEL OUTPUT VOLTAGE HIGH-LEVEL OUTPUT CURRENT VDD = 5 V TA = 4 C TA = 7 C TA = 25 C IOH - High-Level Output Current - ma Figure 5 V OL Low-Level Output Voltage V LOW-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT CURRENT VDD = 5 V TA = 7 C TA = 25 C TA = 4 C IOL - Low-Level Output Current - ma Figure 6 2. HIGH-LEVEL OUTPUT VOLTAGE HIGH-LEVEL OUTPUT CURRENT. LOW-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT CURRENT OUTPUT IMPEDANCE FREQUENCY V OH High-Level Output Voltage V TA = 25 C TA = 7 C VDD = 2 V TA = 4 C IOH - High-Level Output Current - ma Figure 7 V OL Low-Level Output Voltage V TA = 25 C TA = 7 C TA = 4 C. VDD = 2 V IOL - Low-Level Output Current - ma Figure 8 Z o Output Impedance Ω.. k VDD = 5 V and 2 V AV = AV = AV = k k f - Frequency - Hz Figure 9 M M 2

13 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS I DD Supply Current ma SUPPLY CURRENT SUPPLY VOLTAGE TA = 4 C TA = 7 C TA = 25 C AV =.2 SHDN = VDD Per Channel VDD Supply Voltage - V Figure Power Supply Rejection Ratio db PSRR POWER SUPPLY REJECTION RATIO FREQUENCY VDD = 5 V k VDD = 2 V k f Frequency Hz Figure k M M CMRR Common-Mode Rejection Ratio db COMMON-MODE REJECTION RATIO FREQUENCY k VDD = 5 V and 2 V k k M M f - Frequency - Hz Figure 2 nv/ Hz V n Equivalent Input Noise Voltage EQUIVALENT INPUT NOISE VOLTAGE FREQUENCY VDD = 5 V VDD = 2 V k k f Frequency Hz Figure 3 k V O(PP) Peak-to-Peak Output Voltage V k PEAK-TO-PEAK OUTPUT VOLTAGE FREQUENCY VDD = 2 V VDD = 5 V THD+N < = 5% RL = 6 Ω k M M f - Frequency - Hz Figure 4 V O(PP) Peak-to-Peak Output Voltage V k PEAK-TO-PEAK OUTPUT VOLTAGE FREQUENCY VDD = 2 V VDD = 5 V THD+N < = 5% RL= kω k M M f - Frequency - Hz Figure 5 Crosstalk db VDD = 5 V and 2 V AV = RL = kω VI(PP) = 2 V For All Channels CROSSTALK FREQUENCY 4 6 k k f Frequency Hz Figure 6 k 3

14 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS DIFFERENTIAL VOLTAGE GAIN AND PHASE FREQUENCY 8 DIFFERENTIAL VOLTAGE GAIN AND PHASE FREQUENCY 8 Different Voltage Gain db A VD k k Gain VDD = ±2.5 V RL = kω CL = pf k M f Frequency Hz Figure 7 Phase M M Phase Different Voltage Gain db A VD k k Gain VDD = ±6 V RL = kω CL = pf TA = 25 C k M f Frequency Hz Figure 8 Phase M M Phase 4 35 PHASE MARGIN LOAD CAPACITANCE Rnull = Ω Rnull = Ω 45 4 PHASE MARGIN LOAD CAPACITANCE Rnull = Ω GAIN MARGIN LOAD CAPACITANCE Rnull = Ω φ m Phase Margin VDD = 5 V RL = kω Rnull = 5 Ω Rnull = 2 Ω φ m Phase Margin Rnull = Ω VDD = 2 V RL = kω Rnull = 5 Ω Rnull = 2 Ω G Gain Margin db VDD = 5 V RL = kω Rnull = 5 Ω Rnull = Ω Rnull = 2 Ω CL Load Capacitance pf Figure 9 CL Load Capacitance pf Figure 2 CL Load Capacitance pf Figure 2 φ m Phase Margin db GAIN MARGIN LOAD CAPACITANCE Rnull = 5 Ω VDD = 2 V RL = kω Rnull = Ω CL Load Capacitance pf Figure 22 Rnull = Ω Rnull = 2 Ω GBWP - Gain Bandwidth Product - MHz GAIN BANDWIDTH PRODUCT SUPPLY VOLTAGE CL = pf RL = 6 Ω RL = kω VDD - Supply Voltage - V Figure 23 SR Slew Rate V/ µ s SLEW RATE SUPPLY VOLTAGE RL = 6 Ω and kω CL = 5 pf AV = Slew Rate Slew Rate VDD - Supply Voltage - V Figure

15 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS SR Slew Rate V/ µ s SLEW RATE FREE-AIR TEMPERATURE Slew Rate Slew Rate + VDD = 5 V RL= 6 Ω and kω CL = 5 pf AV = SR Slew Rate V/ µ s SLEW RATE FREE-AIR TEMPERATURE Slew Rate + VDD = 2 V RL= 6 Ω and kω CL = 5 pf AV = Slew Rate Total Harmonic Distortion + Noise %. TOTAL HARMONIC DISTORTION PLUS NOISE FREQUENCY. AV = AV = AV = VDD = 5 V VO(PP) = 2 V RL = kω TA - Free-Air Temperature - C Figure TA - Free-Air Temperature - C Figure 26. k k f Frequency Hz Figure 27 k Total Harmonic Distortion + Noise %.. TOTAL HARMONIC DISTORTION PLUS NOISE FREQUENCY AV = AV = AV =. k k f Frequency Hz Figure 28 VDD = 2 V VO(PP) = 8 V RL = kω LARGE SIGNAL FOLLOWER PULSE RESPONSE k Total Harmonic Distortion + Noise % TOTAL HARMONIC DISTORTION PLUS NOISE PEAK-TO-PEAK OUTPUT VOLTAGE... VDD = 5 V AV = f = khz RL = 6 Ω RL = 25 Ω RL = kω VO(PP) Peak-to-Peak Output Voltage V Figure 29 LARGE SIGNAL FOLLOWER PULSE RESPONSE Total Harmonic Distortion + Noise % TOTAL HARMONIC DISTORTION PLUS NOISE PEAK-TO-PEAK OUTPUT VOLTAGE... VDD = 2 V AV = f = khz VO(PP) Peak-to-Peak Output Voltage V Figure 3 RL = 6 Ω RL = 25 Ω RL = kω SMALL SIGNAL FOLLOWER PULSE RESPONSE VI ( V/Div) VI (5 V/Div) VI(mV/Div) Output Voltage V V O VO (5 mv/div) VDD = 5 V RL = 6 Ω and kω CL = 8 pf Output Voltage V V O VO (2 V/Div) VDD = 2 V RL = 6 Ω and kω CL = 8 pf V O Output Voltage V VO(5mV/Div) VDD = 5 V and 2 V RL = 6 Ω and kω CL = 8 pf t Time µs Figure t Time µs Figure t Time µs Figure

16 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS LARGE SIGNAL INVERTING PULSE RESPONSE LARGE SIGNAL INVERTING PULSE RESPONSE SMALL SIGNAL INVERTING PULSE RESPONSE Output Voltage V V O VI (2 V/div) VDD = 5 V RL = 6 Ω and kω CL = 8 pf Output Voltage V V O VI (5 V/div) VDD = 2 V RL = 6 Ω and kω CL = 8 pf Output Voltage V V O VI ( mv/div) VDD = 5 V and 2 V RL = 6 Ω and kω CL = 8 pf VO (5 mv/div) VO (5 mv/div) VO (2 V/Div) t Time µs Figure t Time µs Figure t Time µs Figure 36 Sutdown Forward Isolation - db SHUTDOWN FORWARD ISOLATION FREQUENCY RL = kω VDD = 5 V CL= pf VI(PP) =., 2.5, and 5 V RL = 6 Ω Sutdown Forward Isolation - db SHUTDOWN FORWARD ISOLATION FREQUENCY RL = kω VDD = 2 V CL= pf VI(PP) =., 8, 2 V RL = 6 Ω Sutdown Reverse Isolation - db SHUTDOWN REVERSE ISOLATION FREQUENCY RL = kω VDD = 5 V CL= pf VI(PP) =., 2.5, and 5 V RL = 6 Ω 2 k k k M M f - Frequency - Hz Figure 37 M 2 k k k M M f - Frequency - Hz Figure 38 M 2 k k k M M f - Frequency - Hz Figure 39 M Sutdown Reverse Isolation - db k SHUTDOWN REVERSE ISOLATION FREQUENCY RL = kω VDD = 2 V CL= pf VI(PP) =., 8, 2 V RL = 6 Ω k k M M f - Frequency - Hz Figure 4 M I DD(SHDN) Shutdown Supply Current - µ A SHUTDOWN SUPPLY CURRENT SUPPLY VOLTAGE Shutdown On RL = open VIN = VDD/ VDD - Supply Voltage - V Figure 4 I DD(SHDN) Shutdown Supply Current - µ A SHUTDOWN SUPPLY CURRENT FREE-AIR TEMPERATURE AV = VIN = VDD/2 VDD = 2 V VDD = 5 V TA - Free-Air Temperature - C Figure

17 SLOS254E JUNE 999 REVISED APRIL 26 TYPICAL CHARACTERISTICS I DD Supply Current ma SHUTDOWN PULSE Shutdown Pulse VDD = 5 V CL= 8 pf IDD RL = kω IDD RL = 6 Ω SD Off t - Time - µs Figure Shutdown Pulse - V I DD Supply Current ma SHUTDOWN PULSE Shutdown Pulse VDD = 2 V CL= 8 pf IDD RL = kω IDD RL = 6 Ω SD Off t - Time - µs Figure Shutdown Pulse - V PARAMETER MEASUREMENT INFORMATION _ + Rnull RL CL Figure 45 APPLICATION INFORMATION input offset voltage null circuit The TLC8 and TLC8 has an input offset nulling function. Refer to Figure 46 for the diagram. IN IN + + N kω N2 OUT R NOTE A: R = 5.6 kω for offset voltage adjustment of ± mv. R = 2 kω for offset voltage adjustment of ±3 mv. VDD Figure 46. Input Offset Voltage Null Circuit 7

18 SLOS254E JUNE 999 REVISED APRIL 26 driving a capacitive load APPLICATION INFORMATION When the amplifier is configured in this manner, capacitive loading directly on the output will decrease the device s phase margin leading to high frequency ringing or oscillations. Therefore, for capacitive loads of greater than pf, it is recommended that a resistor be placed in series (R NULL ) with the output of the amplifier, as shown in Figure 47. A minimum value of 2 Ω should work well for most applications. RF Input RG _ + RNULL Output CLOAD Figure 47. Driving a Capacitive Load offset voltage The output offset voltage, (V OO ) is the sum of the input offset voltage (V IO ) and both input bias currents (I IB ) times the corresponding gains. The following schematic and formula can be used to calculate the output offset voltage: RF RG IIB RS VI + + VO IIB+ V OO V IO R F R G I IB R S R F R G I IB R F Figure 48. Output Offset Voltage Model 8

19 high speed CMOS input amplifiers SLOS254E JUNE 999 REVISED APRIL 26 APPLICATION INFORMATION The TLC8x is a family of high-speed low-noise CMOS input operational amplifiers that has an input capacitance of the order of 2 pf. Any resistor used in the feedback path adds a pole in the transfer function equivalent to the input capacitance multiplied by the combination of source resistance and feedback resistance. For example, a gain of, a source resistance of kω, and a feedback resistance of kω add an additional pole at approximately 8 MHz. This is more apparent with CMOS amplifiers than bipolar amplifiers due to their greater input capacitance. This is of little consequence on slower CMOS amplifiers, as this pole normally occurs at frequencies above their unity-gain bandwidth. However, the TLC8x with its -MHz bandwidth means that this pole normally occurs at frequencies where there is on the order of 5dB gain left and the phase shift adds considerably. The effect of this pole is the strongest with large feedback resistances at small closed loop gains. As the feedback resistance is increased, the gain peaking increases at a lower frequency and the 8 phase shift crossover point also moves down in frequency, decreasing the phase margin. For the TLC8x, the maximum feedback resistor recommended is 5 kω; larger resistances can be used but a capacitor in parallel with the feedback resistor is recommended to counter the effects of the input capacitance pole. The TLC83 with a -V step response has an 8% overshoot with a natural frequency of 3.5 MHz when configured as a unity gain buffer and with a -kω feedback resistor. By adding a -pf capacitor in parallel with the feedback resistor, the overshoot is reduced to 4% and eliminates the natural frequency, resulting in a much faster settling time (see Figure 49). The -pf capacitor was chosen for convenience only. Load capacitance had little effect on these measurements due to the excellent output drive capability of the TLC8x. V O Output Voltage V VOUT VIN With CF = pf VDD = ±5 V AV = + RF = kω RL = 6 Ω CL = 22 pf t - Time - µs 2 V I Input Voltage V IN pf kω _ + 5 Ω 6 Ω 22 pf Figure 49. -V Step Response 9

20 SLOS254E JUNE 999 REVISED APRIL 26 general configurations APPLICATION INFORMATION When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier (see Figure 5). RG RF VI R V O V I C + f 3dB R F R G src VO 2 RC Figure 5. Single-Pole Low-Pass Filter If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this task. For best results, the amplifier should have a bandwidth that is 8 to times the filter frequency bandwidth. Failure to do this can result in phase shift of the amplifier. VI R R2 C2 C + _ R = R2 = R C = C2 = C Q = Peaking Factor (Butterworth Q =.77) f 3dB 2 RC RG RF RG = ( RF 2 Q ) Figure 5. 2-Pole Low-Pass Sallen-Key Filter 2

21 SLOS254E JUNE 999 REVISED APRIL 26 APPLICATION INFORMATION shutdown function Three members of the TLC8x family (TLC8/3/5) have a shutdown terminal (SHDN) for conserving battery life in portable applications. When the shutdown terminal is tied low, the supply current is reduced to 25 µa/channel, the amplifier is disabled, and the outputs are placed in a high-impedance mode. To enable the amplifier, the shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to the voltage on the GND terminal of the device. Therefore, when operating the device with split supply voltages (e.g. ±2.5 V), the shutdown terminal needs to be pulled to V DD (not system ground) to disable the operational amplifier. The amplifier s output with a shutdown pulse is shown in Figure 43 and Figure 44. The amplifier is powered with a single 5-V supply and is configured as noninverting with a gain of 5. The amplifier turnon and turnoff times are measured from the 5% point of the shutdown pulse to the 5% point of the output waveform. The times for the single, dual, and quad are listed in the data tables. Figure 37 through Figure 4 show the amplifier s forward and reverse isolation in shutdown. The operational amplifier is configured as a voltage follower (A V = ). The isolation performance is plotted across frequency using. V PP, 2.5 V PP, and 5 V PP input signals at ±2.5 V supplies and. V PP, 8 V PP, and 2 V PP input signals at ±6 V supplies. circuit layout considerations To achieve the levels of high performance of the TLC8x, follow proper printed-circuit board design techniques. A general set of guidelines is given in the following. Ground planes It is highly recommended that a ground plane be used on the board to provide all components with a low inductive ground connection. However, in the areas of the amplifier inputs and output, the ground plane can be removed to minimize the stray capacitance. Proper power supply decoupling Use a 6.8-µF tantalum capacitor in parallel with a.-µf ceramic capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers depending on the application, but a.-µf ceramic capacitor should always be used on the supply terminal of every amplifier. In addition, the.-µf capacitor should be placed as close as possible to the supply terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less effective. The designer should strive for distances of less than. inches between the device power terminals and the ceramic capacitors. Sockets Sockets can be used but are not recommended. The additional lead inductance in the socket pins will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board is the best implementation. Short trace runs/compact part placements Optimum high performance is achieved when stray series inductance has been minimized. To realize this, the circuit layout should be made as compact as possible, thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at the input of the amplifier. Surface-mount passive components Using surface-mount passive components is recommended for high performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be kept as short as possible. 2

22 SLOS254E JUNE 999 REVISED APRIL 26 general PowerPAD design considerations APPLICATION INFORMATION The TLC8x is available in a thermally-enhanced PowerPAD family of packages. These packages are constructed using a downset leadframe upon which the die is mounted [see Figure 52(a) and Figure 52(b)]. This arrangement results in the lead frame being exposed as a thermal pad on the underside of the package [see Figure 52(c)]. Because this thermal pad has direct thermal contact with the die, excellent thermal performance can be achieved by providing a good thermal path away from the thermal pad. DIE Side View (a) Thermal Pad DIE End View (b) Bottom View (c) NOTE B: The thermal pad is electrically isolated from all terminals in the package. Figure 52. Views of Thermally-Enhanced DGN Package The PowerPAD package allows for both assembly and thermal management in one manufacturing operation. During the surface-mount solder operation (when the leads are being soldered), the thermal pad must be soldered to a copper area underneath the package. Through the use of thermal paths within this copper area, heat can be conducted away from the package into either a ground plane or other heat dissipating device. Soldering the PowerPAD to the printed circuit board (PCB) is always required, even with applications that have low power dissipation. This soldering provides the necessary thermal and mechanical connection between the lead frame die pad and the PCB. Although there are many ways to properly heatsink the PowerPAD package, the following steps illustrate the recommended approach. 22

23 SLOS254E JUNE 999 REVISED APRIL 26 APPLICATION INFORMATION general PowerPAD design considerations (continued) The PowerPAD must be connected to the most negative supply voltage (GND pin potential) of the device.. Prepare the PCB with a top side etch pattern (see the landing patterns at the end of this data sheet). There should be etch for the leads as well as etch for the thermal pad. 2. Place five holes (dual) or nine holes (quad) in the area of the thermal pad. These holes should be 3 mils in diameter. Keep them small so that solder wicking through the holes is not a problem during reflow. 3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps dissipate the heat generated by the TLC8x IC. These additional vias may be larger than the 3-mil diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad area to be soldered so that wicking is not a problem. 4. Connect all holes to the internal plane that is at the same potential as the ground pin of the device. 5. When connecting these holes to this internal plane, do not use the typical web or spoke via connection methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat transfer during soldering operations. This makes the soldering of vias that have plane connections easier. In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore, the holes under the TLC8x PowerPAD package should make their connection to the internal ground plane with a complete connection around the entire circumference of the plated-through hole. 6. The top-side solder mask should leave the terminals of the package and the thermal pad area with its five holes (dual) or nine holes (quad) exposed. The bottom-side solder mask should cover the five or nine holes of the thermal pad area. This prevents solder from being pulled away from the thermal pad area during the reflow process. 7. Apply solder paste to the exposed thermal pad area and all of the IC terminals. 8. With these preparatory steps in place, the TLC8x IC is simply placed in position and run through the solder reflow operation as any standard surface-mount component. This results in a part that is properly installed. For a given θ JA, the maximum power dissipation is shown in Figure 53 and is calculated by the following formula: P D T MAX T A JA Where: P D = Maximum power dissipation of TLC8x IC (watts) T MAX = Absolute maximum junction temperature (5 C) T A = Free-ambient air temperature ( C) θ JA = θ JC + θ CA θ JC = Thermal coefficient from junction to case θ CA = Thermal coefficient from case to ambient air ( C/W) 23

24 SLOS254E JUNE 999 REVISED APRIL 26 APPLICATION INFORMATION general PowerPAD design considerations (continued) Maximum Power Dissipation W MAXIMUM POWER DISSIPATION FREE-AIR TEMPERATURE DGN Package Low-K Test PCB θ JA = 52.3 C/W PDIP Package Low-K Test PCB θ JA = 4 C/W PWP Package Low-K Test PCB θ JA = 29.7 C/W SOT-23 Package Low-K Test PCB θ JA = 324 C/W T J = 5 C SOIC Package Low-K Test PCB θ JA = 76 C/W TA Free-Air Temperature C NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB. Figure 53. Maximum Power Dissipation Free-Air Temperature The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent power and output power. The designer should never forget about the quiescent heat generated within the device, especially multi-amplifier devices. Because these devices have linear output stages (Class A-B), most of the heat dissipation is at low output voltages with high output currents. The other key factor when dealing with power dissipation is how the devices are mounted on the PCB. The PowerPAD devices are extremely useful for heat dissipation. But, the device should always be soldered to a copper plane to fully use the heat dissipation properties of the PowerPAD. The SOIC package, on the other hand, is highly dependent on how it is mounted on the PCB. As more trace and copper area is placed around the device, θ JA decreases and the heat dissipation capability increases. The currents and voltages shown in these graphs are for the total package. For the dual or quad amplifier packages, the sum of the RMS output currents and voltages should be used to choose the proper package. 24

25 macromodel information SLOS254E JUNE 999 REVISED APRIL 26 APPLICATION INFORMATION Macromodel information provided was derived using Microsim Parts, the model generation software used with Microsim PSpice. The Boyle macromodel (see Note ) and subcircuit in Figure 54 are generated using the TLC8x typical electrical and operating characteristics at T A = 25 C. Using this information, output simulations of the following key parameters can be generated to a tolerance of 2% (in most cases): Maximum positive output voltage swing Unity-gain frequency Maximum negative output voltage swing Common-mode rejection ratio Slew rate Phase margin Quiescent power dissipation DC output resistance Input bias current AC output resistance Open-loop voltage amplification Short-circuit output current limit NOTE 2: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, Macromodeling of Integrated Circuit Operational Amplifiers, IEEE Journal of Solid-State Circuits, SC-9, 353 (974). PSpice and Parts are trademarks of MicroSim Corporation. 25

26 SLOS254E JUNE 999 REVISED APRIL 26 APPLICATION INFORMATION VDD RP 2 IN IN + DP 3 RSS ISS J J2 RD C 2 RD2 VC DC + R2 53 EGND 9 + VB 6 GCM 99 + FB C2 GA 9 RO2 HLIM 7 + VLIM 8 + DLP DLN VLP VLN + GND VAD + + VE * TLC8X_5V 5V operational amplifier macromodel subcircuit * created using Parts release 8. on 2/6/99 at 4:3 * Parts is a MicroSim product. * * connections: non-inverting input * inverting input * positive power supply * negative power supply * output *.subckt TLC8X_5V * c E 2 c E 2 css E 5 dc 5 53 dy de 54 5 dy dlp 9 9 dx dln 92 9 dx dp 4 3 dx egnd 99 poly(2) (3,) (4,).5.5 fb 7 99 poly(5) vb vc ve vlp vln 3.984E6 E3 E3 4E6 4E6 4 6 *DEVICE=TLC8X_5V, OPAMP, PJF, INT 54 DE OUT ga E 6 gcm E 6 ioff 6 dc.22e 6 iss 3 dc 3.4E 6 hlim 9 vlim K j 2 jx j2 2 jx2 r2 6 9.E3 rd E3 rd E3 ro 8 5 ro rp E3 rss E6 vb 9 dc vc 3 53 dc.5537 ve 54 4 dc vlim 7 8 dc vlp 9 dc 7.6 vln 92 dc 7.6.model dx D(Is=8.E 8).model dy D(Is=8.E 8 Rs=m Cjo=p).model jx PJF(Is=8.E 5 Beta=.24E 3 Vto= ).model jx2 PJF(Is=8.E 5 Beta=.24E 3 Vto= ).ends 5 RO Figure 54. Boyle Macromodel and Subcircuit 26

27 Power-On Reset Generator Automatic Reset Generation After Voltage Drop Low Standby Current...2 µa RESET Output Defined When V CC Exceeds V Precision Threshold Voltage 4.55 V ±2 mv High Output Sink Capability... 2 ma Comparator Hysteresis Prevents Erratic Resets description/ordering information The TL7757 is a supply-voltage supervisor designed for use in microcomputer and microprocessor systems. The supervisor monitors the supply voltage for undervoltage conditions. During power up, when the supply voltage, V CC, attains a value approaching V, the RESET output becomes active (low) to prevent undefined operation. If the supply voltage drops below threshold voltage level (V IT ), the RESET output goes to the active (low) level until the supply undervoltage fault condition is eliminated. TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 RESET V CC NC GND D PACKAGE (TOP VIEW) NC No internal connection LP PACKAGE (TOP VIEW) PK PACKAGE (TOP VIEW) NC NC NC NC GND V CC RESET RESET GND VCC TA ORDERING INFORMATION PACKAGE ORDERABLE PART NUMBER TL7757CD TL7757CDR GND is in electrical contact with the tab. TOP-SIDE MARKING SOIC (D) Tube of 75 Reel of C C to 7 C SOT (PK) Reel of TL7757CPK T7 TO226 / TO-92 (LP) Bulk of TL7757CLP Reel of 2 TL7757CLPR TL7757C SOIC (D) Tube of 75 TL7757ID Reel of 25 TL7757IDR 7757I 4 C to 85 C SOT (PK) Reel of TL7757IPK 7I TO226 / TO-92 (LP) Bulk of TL7757ILP Reel of 2 TL7757ILPR TL7757I Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 23, Texas Instruments Incorporated POST OFFICE BOX DALLAS, TEXAS 75265

28 TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 equivalent schematic VCC RESET R Q R2 R3 R4 Q2 R5 R6 R8 Q3 R9 R Q4 R Q5 Q6 R2 C Q7 Q8 Q9 Q Q Q2 R5 Q3 Q5 Q7 C2 R4 Q8 Q4 Q6 R6 Q9 Q2 Q2 R8 R7 R3 GND ACTUAL DEVICE COMPONENT COUNT Transistors 27 Resistors 2 Capacitors 2 absolute maximum ratings over operating junction temperature range (unless otherwise noted) Supply voltage range, V CC (see Note ) V to 2 V Off-state output voltage range (see Note ) V to 2 V Output current, I O ma Package thermal impedance, θ JA (see Notes 2 and 3): D package C/W LP package C/W PK package C/W Operating virtual junction temperature, T J C Lead temperature,6 mm (/6 inch) from case for seconds C Storage temperature range, T stg C to 5 C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES:. All voltage values are with respect to network terminal ground. 2. Maximum power dissipation is a function of TJ(max), θ JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) TA)/θ JA. Operating at the absolute maximum TJ of 5 C can affect reliability. 3. The package thermal impedance is calculated in accordance with JESD POST OFFICE BOX DALLAS, TEXAS 75265

29 TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 recommended operating conditions MIN MAX UNIT VCC Supply voltage 7 V VOH High-level output voltage 5 V IOL Low-level output current 2 ma TA Operating free-air temperature TL7757C 7 TL7757I 4 85 C electrical characteristics at specified free-air temperature VIT PARAMETER TEST CONDITIONS TA Negative-going input threshold voltage at VCC Vhys Hysteresis at VCC VOL Low-level output voltage IOL = 2 ma, VCC = 4.3 V IOH High-level output current Vres Power-up reset voltage ICC Supply current TL7757C MIN TYP MAX 25 C C to 7 C C C to 7 C C.4.8 C to 7 C.8 VCC = 7 V, VOH = 5 V, 25 C See Figure C to 7 C RL = 2.2 kω, 25 C.8 VCC slew rate 5 V/µs C to 7 C.2 VCC = 4.3 V 25 C 4 2 UNIT V mv V µa V C to 7 C 2 µa VCC = 5.5 V C to 7 C 4 This is the difference between positive-going input threshold voltage, VIT+, and negative-going input threshold voltage, VIT. This is the lowest voltage at which RESET becomes active. switching characteristics at specified free-air temperature PARAMETER TEST CONDITIONS TA TL7757C MIN TYP MAX tplh Propagation delay time, low-to-high-level VCC slew rate 5 V/µs, 25 C output See Figures 2 and 3 C to 7 C 5 tphl Propagation delay time, high-to-low-level 25 C 2 5 See Figures 2 and 3 output C to 7 C 5 V/µs, 25 C.4 tr Rise time VCC slew rate 5 See Figures 2 and 3 C to 7 C 25 C.5 tf Fall time See Figures 2 and 3 C to 7 C Minimum pulse duration at VCC for output 25 C 5 tw(min) response C to 7 C 5 UNIT µs µs µs µs µs POST OFFICE BOX DALLAS, TEXAS

30 TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 electrical characteristics at specified free-air temperature VIT PARAMETER TEST CONDITIONS TA Negative-going input threshold voltage at VCC Vhys Hysteresis at VCC VOL Low-level output voltage IOL = 2 ma, VCC = 4.3 V IOH High-level output current Vres Power-up reset voltage ICC Supply current TL7757I MIN TYP MAX 25 C C to 85 C C C to 85 C C C to 85 C.8 VCC = 7 V, VOH = 5 V, 25 C See Figure 4 C to 85 C RL = 2.2 kω, 25 C.8 VCC slew rate 5 V/µs 4 C to 85 C.2 VCC = 4.3 V 25 C 4 2 UNIT V mv V µa V 4 C to 85 C 2 µa VCC = 5.5 V 4 C to 85 C 4 This is the difference between positive-going input threshold voltage, VIT+, and negative-going input threshold voltage, VIT. This is the lowest voltage at which RESET becomes active. switching characteristics at specified free-air temperature TL7757I PARAMETER TEST CONDITIONS TA MIN TYP MAX V/µs, 25 C tplh Propagation delay time, low-to-high-level output VCC slew rate 5 See Figures 2 and 3 4 C to 85 C 5 25 C 2 5 tphl Propagation delay time, high-to-low-level output See Figures 2 and 3 4 C to 85 C 5 V/µs, 25 C.4 tr Rise time VCC slew rate 5 See Figures 2 and 3 4 C to 85 C 25 C.5 tf Fall time See Figures 2 and 3 4 C to 85 C Minimum pulse duration at VCC for output 25 C 5 tw(min) response 4 C to 85 C 5 UNIT µs µs µs µs µs 4 POST OFFICE BOX DALLAS, TEXAS 75265

31 PARAMETER MEASUREMENT INFORMATION TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 5 V + VCC TL7757 A 5.5 V RESET GND Figure. Test Circuit for Output Leakage Current VCC TL7757 RL = kω Pulse Generator. F RESET OUT GND CL = pf (see Note A) NOTE A: Includes jig and probe capacitance Figure 2. Test Circuit for RESET Output Switching Characteristics 4.8 V VCC (see Note A) VIT+ 4.3 V tplh VIT tphl RESET 9% 5% % 9% 5% % tr NOTE A: VCC slew rate 5 µs tf Figure 3. Switching Diagram POST OFFICE BOX DALLAS, TEXAS

32 TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VCC Supply voltage RESET output voltage 4 ICC Supply current Supply voltage 5 ICC Supply current Free-air temperature 6 VOL Low-level output voltage Low-level output current 7 VOL Low-level output voltage Free-air temperature 8 IOL Output current Supply voltage 9 VIT Input threshold voltage (negative-going VCC) Free-air temperature Vres Power-up reset voltage Free-air temperature Vres Power-up reset voltage and supply voltage Time 2 Propagation delay time 3 SUPPLY VOLTAGE RESET OUTPUT VOLTAGE SUPPLY CURRENT SUPPLY VOLTAGE 8 7 IO = 2 IO = RESET Output Voltage V Output Undefined IDD CC Supply Current ma VCC Supply Voltage V Figure 4 VCC Supply Voltage V Figure 5 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 6 POST OFFICE BOX DALLAS, TEXAS 75265

33 TYPICAL CHARACTERISTICS TL7757 SUPPLY-VOLTAGE SUPERVISOR AND PRECISION VOLTAGE DETECTOR SLVS4I SEPTEMBER 99 REVISED AUGUST 23 IDD CC Supply Current ma RL = SUPPLY CURRENT FREE-AIR TEMPERATURE VCC = 4.3 V VCC = 7 V VCC = 5.5 V TA Free-Air Temperature C Figure VOL V Low-Level Output Voltage mv LOW-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT CURRENT VCC = V VCC = 4.3 V IOL Low-Level Output Current ma Figure LOW-LEVEL OUTPUT VOLTAGE FREE-AIR TEMPERATURE VCC = 4.3 V IOL = 2 ma.2.8 OUTPUT CURRENT SUPPLY VOLTAGE VOL V Low-Level Output Voltage mv IOL = 8 ma IOL = ma IO Output Current ma TA Free-Air Temperature C Figure VCC Supply Voltage V Figure Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX DALLAS, TEXAS